Search Documents

By E. Lee

With the growing environmental concern, as well as the increasing concern for sustainability of natural resources, the need of improving the performance and efficiency of today?s crushers is be-coming increasingly important. However, the development of existing crushers requires an extended basic knowledge about the crushing process itself. The aim of the present study is therefore to find the theoretically optimal way of crushing compressively under given circumstances. In the present paper, optimizations have been performed with the purposes of maximizing product yield and minimizing energy consumption. Performed on an ideal crushing stage free from physical limitations, the optimization results have been obtained in terms of number of compressions and their corresponding compression ratios. Complementing earlier results on interparticle breakage (Hulthén et al., 2006), presented here are thus the results from corresponding optimizations with single particle breakage and interparticle breakage. It is concluded that modern crushers are not working optimally in any of the studied aspects for gneiss. In fact, optimizations indicate that a lowering of the compression ratio, as well as a shortening of the crushing sequence, are theoretically favourable. The outcome of this study is therefore highly promising as to giving new ideas and suggestions of improvements in existing crushers, and can even result in redesign of compression crushers.

Jan 1, 2014

By F. Q. Cheng

As the important potash, the product yield of KCl in winter is low and the resources waste is serious according to the deficiency of collectors, which can be used in this condition currently. This paper studied on the change of contact angle, turbidity, and flotation recovery of KCl particles when different chain lengths, ratios of amines were used as collectors in KCl flotation process to get a new mixed collector. The contact angle values of KCl crystal in its brine solution added different amine collectors were first measured by captive bubble method. The turbidity of brine solutions were then measured by the laboratory turbidimeter at room temperature when different amine collectors were contained. In the end micro-flotation experiment using mixed amine with fixed ratios and ODA as collectors respectively at 5 °C, 23 °C were performed. The results show when the ratio of the mixed amine is DDA- 20%, ODA-60%, C20-20%, the contact angle at KCl surface is the maximum and the hydrophobic state is best. Meanwhile the result of turbidity measurement indicates that the dispersion of mixed amine colloids is better than the ODA collector due to the addition of DDA, which plays the role of frother. The flotation results also prove that the mixed amine is not only fit for the KCl flotation at room temperature but also fit for its flotation at low temperature. This study provides strong technical support to extend the production time of potash business in Chaerhan areas in China.

Sep 1, 2012

By R. Mukherjee

Consistency of Run-Off-Mine (ROM) quality plays an important role in mineral processing which is not very often talked about. The major impediment is limitation of sampling ROM ore, which makes processing plants to run without any realtime feedback on ore quality that comes in. The process of direct determination of Run-Off-Mine (ROM) ore quality is expensive and time consuming as drawing and preparing representative samples from blasted muckpiles are constrained by large sample size and inherent heterogeneity in terms of size and chemistry. In absence of techniques for direct measurement of quality, monitoring and control of ROM, feed to the processing plant at Joda East Mine, like all other iron ore beneficiation plants worldwide, is largely based on blasthole sampling and subsequent chemical analyses of blastcone chips. While such indirect methods proves to be more accurate for representing whole of a mining block or blasted muckpile (~30-50KT/blast), it is indeed a challenge to ascertain and predict day to day input quality for a part there off. This eventually leads to a gap between predicted and actual ROM quality, resulting in difficulties in process control, in turn, and leading to wide swings in product quality. Hence, it is imperative to bridge the gap between predicted and actual ROM quality by arriving at means, which ensure consistent plant feed grade to deliver consistent output. The paper discusses an efficient and affordable alternative for effective prediction of ROM alumina which has been developed by integrating blasthole quality database in GPS based Truck Dispatch System (GPS-TDS) at Joda East Mine. Initially, GPS-TDS has been installed for optimizing production parameters only, but this development has helped in further utilization of GPS-TDS for real time quality monitoring by improving ROM grade prediction and scheduling from several ore blocks in active mining areas. Keywords:run-off-mine (ROM), blast hole, feed grade, GPS-TDS

Sep 1, 2012

By A. D. Bas

Copper minerals present difficulties during the cyanide leaching of gold ores leading to excessively high consumption of cyanide (and oxygen) coupled with low extraction of gold. Copper cyanide species, if present at high levels, adversely affects the downstream processes such as the activated carbon adsorption and the effluent treatment. In this study, the extraction of gold from a copper-bearing gold ore by ammoniacal cyanide leaching was studied. Furthermore, ammonia leaching as a pretreatment process ahead of cyanide leaching was also examined. Only ~12% of gold was extracted by direct cyanide leaching of the ore. The addition of lead nitrate did not affect the leaching of gold. When ammoniacal cyanide leaching system was used, the extraction of gold was significantly improved to >90%. Similarly, the pretreatment of the ore by ammonia leaching was shown to lead to high gold extractions (98%), in subsequent cyanide leaching with significant reductions in the consumption of cyanide. This appeared to be linked with the ready dissolution/removal of copper during ammonia leaching.

Sep 1, 2012

By S. K. Chaudhuri

With a growing emphasis on maximizing the value by rapidly deploying it across their assets, mining firms are eager to identify any issues that may hinder such efforts and to refine their approaches to overcome them. As such a CDE vision can be considered realized when the following components are addressed and functioning as intended - People: the right resources working together and efficiently to achieve shared goals, Process: well-defined workflows mapped out for key value processes, Technology: availability of the correct tools and applications to increase efficiency in work execution and Locations: regional locations/ sites that need to be linked for collaboration and information exchange. For the above vision, an approach that considers the degree of interaction between the roles in metallurgy operations, mineral resource planning, mine engineering, plant operations, logistics and infrastructure, and which accounts for the current technology states across these groups to determine sub-processes where the impact of a CDE will be the most is critical. In effect, CDE is more about transforming an organization?s operational philosophy than a technology driven project. This paper examines the definition and components of a CDE in a mining context. Real-time operations co-ordination, maintenance interventions, production analysis and optimization processes are examined along with current state technologies and manual processes as candidates which are likely to result in most benefits from collaborative work processes. Finally, the paper examines technologies that can be used to further enable a collaborative working environment.

Sep 1, 2012

By M. Etelapaa

A new approach to controlling the process of selective flotation of sulphide minerals from pyrite in a lime environment is covered in the presentation. Advantages of process control based on the electrochemical potential of slurry controlled by ?? ? electrode are proved and compared to conventional methods of ?? ? metering and conductometry. Keywords: flotation, electrochemical potential, automation dosing system, neural network

Sep 1, 2012

The ball level and pulp load play a key role in the operation of industrial scale ball mills. These two operating variables have a significant influence on the performance of the ball mill and any attempts to optimize these devices require manipulating either one or both of these variables. There are several models that can be employed to perform simulations to optimize the performance of industrial ball mills. However, most of these models require ball load and pulp load measurements as inputs to calibrate the model. The changes suggested by the simulator also provide operating regimes that involve moving either the ball level or pulp load and sometimes both of these variables. A ball mill model coded in JKSimMet was used in conjunction with the Sensomag to optimize the secondary ball mill at Waterval concentrator in South Africa. The results show that the perfect mixing ball mill model can be used in conjunction with the Sensomag to optimize the performance of the secondary ball mill.

Sep 1, 2012

By Claudio L. Schneider, Peter R. King, Reiner Neumann

"Predicting the liberation spectra that are produced from breakage of two-phase ores under the random fracture assumption can be accomplished by measuring the conditional, on length, linear grade distribution directly from images obtained from a representative sample of the unbroken texture. The technique tremendously simplifies the prediction problem by avoiding the multiple convolutions that arise from the traditional method based on a description of texture from a measurement of the chord length distributions associated with each phase in the unbroken texture. For a 3-phase system, the phase transition probabilities associated with the textural information make the traditional calculation an almost insurmountable mathematical problem. The direct measurement procedure on the other hand can be expanded to three phases comparatively easily.A coal sample is used here to demonstrate the procedure. It is concluded that the conditional, on length, linear grade distribution can be predicted in the same fashion for multi-phase systems. Accurate stereological conversion is the practical hurdle to be overcome for multi-phase systems, but it is already a reality for 3- phase systems."

Jan 1, 2003

By M. M. Yahyaei

The Sarcheshmeh new concentration plant uses a 32 ft×16 ft constant speed (10.5 RPM) SAG mill with two 5500 hp motors which could rotate in two directions. The mill liners are chrome-molybdenum steel casting type with a Brinnell hardness between 325 and 375 with the lifter face angle of 14° and lifter height of 152 mm. The shell liner consists of 120 (two 60 rows) pieces with a High-High configuration in a rail design. A specially designed liner wear profile measuring device enabled fast and accurate measurements inside the mill during the mill shut-down periods. The measurements indicated that the liner wear profile along the liner length is non-uniform and the highest wear occurs between 1.25m and 2.75m of the mill length. The average weight of liners at the time of removal was 47% of the original weight indicating a significant metal loss. The modification of liner shape was undertaken with the aim of having a uniform profile at the liner removal time. The proposed liner unlike the pervious type did not have a uniform shape with a lifter height of 187mm at the section where the wear rate was high. It was believed that this new profile could arrive at a uniform profile at the liner change out time. A study was also directed to the possible change of charge motion due to the liner profile modification. The dynamic behaviour of charge was investigated through the analysis of forces acting on a single ball using mill characteristics such as mill diameter, rotational speed, lifter height and release angle. The simulation of charge motion with this method and Milltraj TM software indicated that the impact position of charge will change only one degree due to the maximum increase of 35 mm in the lifter height. This assured that the installation of the modified liner would not have any adverse effect on the mill because of ball impacting the mill shell. It was predicated that the amount of scrap metal will reduce to 30% from the current value of 47% beside 1500 h increase in the liner life time.

Jan 1, 2014

By John A. Herbst

The Mineral Processing Industry needs accurate Production Simulators for the design of future plants and expansions. To achieve this, these simulators should not only provide an accurate portrayal of the dynamics of individual pieces of equipment they should include the impact of discrete stochastic events such as scheduled and unscheduled maintenance so the relationships between availability, equipment sizes, and plant capacity are understood. To provide such a tool accurate dynamic Population Balance Models need to be combined with solid discrete event modeling. The current paper provides a description of how these two disparate modeling techniques were combined and the associated benefits from this combination. Keywords: dynamic plant simulation, population balance models, discrete event models, prefeasibility and feasibility studies, plant design and expansion

Sep 1, 2012

By Q. Shi

An investigation into the hydrophobic aggregation of ultrafine smithsonite in surfactant solution has been undertaken through a combination of hydrophobic flocculation experiments, zeta potential measurements, surface tension measurements, and contact angle measurements. The experimental results have revealed that the behaviors of hydrophobic aggregation were closely correlated with the particle hydrophobicity, but they were not lowered byte change of the particle surface charges due to surfactants adsorption. On the other hand, the liquid (solution) surface tension (?LV) plays an important role in hydrophobic aggregation, and the hydrophobic aggregation could not occur below the critical liquid (solution) surface tension (?c). Meanwhile, this flocculation has been observed to require sufficient stirring strength and magnitudes of kinetic energy input to achieve the maximum aggregation degree. From the microflotation results, it has been found that the flotation kinetics response of smithsonite fines is markedly improved due to sufficient stirring strength, and the stirring strength influenced the floc flotation in a manner quite similar to their influence on the hydrophobic aggregation, suggesting that the formation of hydrophobic flocs is a promising means to recover smithsonite in the fine size range.

Sep 1, 2012

By T. J. Chen

Vanadium-beard bone coal is one of important vanadium resources in China.To extract vanadium tailings from Stone coal is produced after extracted vanadium from stone coal through the roasting, leaching and other processes. About 120-150 tons of tailings will be produced in extracting 1 ton of vanadium pentoxide. A lot of tailings that are willfully piled up have caused serious environmental pollution and wasting of resources; it is therefore necessary to realize its resource utilization. This study increases the activity of vanadium tailings by means of alkali fusion, and then uses different alkali activators to react with vanadium tailings so that geopolymer with high value added is produced. Sample of geopolymer is acquired from a mixture containing vanadium tailings, alkali activators, water and a little sodium aluminate through compression-molding process under 20MPa pressure. After cured in room temperature for three days, the maximum compressive strength of the sample can reach 36.2MPa. XRD analysis indicates quartz, the major crystal phase in vanadium tailings is decomposed,and the activity of vanadium tailings is heightened. FTIR and SEM analyses show: structural change having an important impact on the mechanical strength of geopolymer occurred during the process of vanadium tailings generating geopolymer.

Sep 1, 2012

By Mario Gerards, Marco Steinberg, Jan Huben

"Wet high intensity magnetic separation or WHIMS is a widely used technical process for the recovery of magnetic susceptible iron ore particles, mostly for fine and ultrafine grain sizes. The JONES® WHIMS - Wet High Intensity Magnetic Separator, has been used for many years and in countries all around the world. This paper outlines the physical principles utilized for the separation inside the unit, as well as some of the recent changes and developments on the design. It will also give an outlook on the theoretical potential of different alternative yoke materials. The aim of this paper is to analyse the suitability of different yoke materials to improve the equipment. This will be done comparing the magnetic and mechanical parameters and analysing availability and price to find the best compromise regarding cost and benefit. As far as the different kinds of materials are concerned, a special material has been identified as suitable during the comparison exercise. After running the economical calculations, especially with respect to the reduction of the total power consumption of the equipment, a tremendous reduction of the total power consumption has been determined. In addition, to the theoretical exercises and due to the promising results of the same, the Pilot Unit P 40 of the JONES® WHIMS has been manufactured with the special material in order to get practical results as well. Finally, this paper outlines the theoretical and practical results focused on the power consumption. The results are showing that the total power consumption can be reduced tremendously. Hence, the way for a new generation of JONES® WHIMS - environmentally friendly - has been paved."

Jan 1, 2014

By B. Rai

Processing of dolomitic phosphate ores remains one of the most challenging problems in phosphate ore beneficiation. The beneficiation plant at Jhamarkotra in Rajasthan, India for example is currently using a conventional double stage flotation process which involves first a fatty acids flotation to produce a combined dolomite-apatite concentrate (bulk concentrate) from associated silicate gangue. Dolomite is then separated from this bulk concentrate by flotation with fatty acids collectors and depressing apatite with phosphoric acid and sulphuric acid. This process requires addition of large dosages of reagents (H3PO4 and H2SO4) to depress apatite and to maintain highly acidic pH during flotation. Furthermore several cleaning and scavenging stages are needed to obtain the product of desired quality. We have developed and employed a molecular modelling based methodology of designing selective reagents for apatite-dolomite separation. We have been able to take into ac-count the differences in the distribution of calcium cations on these two surfaces in our design and hence develop novel phosphonic acid based depressants for apatite-dolomite separation with con-ventional fatty acids as flotation collectors. We have demonstrated the utility and power of molecular modelling based reagents design approach through this work on beneficiation of Jhamarkotra dolomitic phosphate ore using our novel phosphonic acids based depressants at pH?s close to natural pH. It was possible to reduce the MgO content of the ore from as high as 13.3 % to 1.5% in a single stage flotation. Our flotation separation results on Jhamarkotra ore with these new phosphonic acids based tailor-made depressants for apatite-dolomite flotation separation are discussed in this paper along with results of corresponding molecular modelling computations on the same system.

Jan 1, 2014

By Avinash Tripathi

It is now well known that the size distribution of the particulate solid has a significant effect on the breakage behavior of particles in the wet as well as dry modes of ball milling operation. In the context of the size discretized batch grinding kinetic model, grinding behavior of particles is characterized by the breakage rate parameters, k, and breakage distribution parameters, B. Understanding the nature of variation of these two sets of parameters with particle size distribution is important for simulation and control of operation of production mills. However, so far it has not been possible to track the variation of both the set of parameters with grinding time simultaneously. In this paper an attempt has been made in this direction by using a modified functional form approach with time dependent constants. Keywords: dry and wet ball milling, breakage rate and distribution parameters, effect of particle size distribution

Sep 1, 2012

By Janne Kytökari

Controlling a wide range of minerals processes with single control system is an ordinary way to operate in mines all over the world these days. However the potential of these systems is not yet fully recognized nor utilized. The key issue is to manage the information in a way that enables automating the day-to-day tasks, quality control and safety functions. At the same time it provides means for optimization and constant improvement of processes creating a working environment where the system helps employees to do their key tasks instead of searching, modifying, and transmitting the huge number of information arising every day. The distribution of control system nodes enables the other processes to run heedless of a problem occurring in one of the sub-processes. Also the control room can be in remote location such as in large city removing the need to travel substantially long distances to plant sites every day. When all essential information is brought to the same place there is less risk for a mishap to happen due to information breaks that are often the cause of them. One of the biggest single reasons that result in production losses are break downs of machinery usually caused by normal wear, misuse, incorrect utilization rate etc. For this reason it is important to measure the condition of machines using vibration measurement and diagnostics. By moving from failure or time-based maintenance towards predictive or performance maintenance generates eventually a steady and predictable process but also results in significant long term savings. The mineral process at Talvivaara mine is based on bioheapleaching, whereby metals are leached from ore as a result of bacterial action. Bioleaching is a fairly new technology used in metals recovery. Therefore it is important for the mine to collect and analyze data from different stages of the minerals process. Talvivaara mine?s Metso DNA system has integrated machine condition monitoring and information management. These are not only necessary but also crucial in environmental conditions where the outside temperature can drop below -35°C, where ice and snow dominate the landscape and impact the equipment for four months a year and where distances between equipment can be up to 7.5 kilometers. Keywords: DCS, analyzer, machine condition monitoring, automation, remote communications, optimization, mining, metso DNA, Talvivaara

Sep 1, 2012

By Lang Shiping

The criteria for designing a crushing chamber are presented and a program for designing the shape of the chamber is proposed. During the chamber shape design, major design parameters are analyzed first, optimized parameters are determined next and the basic shape of chamber is figured out finally. In the basic chamber design program, the influence of abrasion of basic chamber shape and material characteristic are not accounted for usually. Here, based on the minimum abrasion of chamber shape and uniform particle size theory, the equation for chamber surface curve and the transcending function were formulated and a low-abrasion chamber was designed. Since the chamber shape designed based on experience and experiments is not necessarily the best, optimal design of the crushing chamber shape was carried out. Cubic spline function was used to represent the chamber shape curve and a mathematical model was formulated. The optimal shape solution was obtained using a complex method. Finally, the optimal chamber shape was determined by matching the moving cone stroke S, moving cone speed N and the moving cone bottom angle Thus, superior technical performance of the cone chamber was achieved.

Sep 1, 2012

By X. Tong

Flotation researches of indium-beard marmatite from the Dulong multi-metallic ore in the Yunnan Province of China has been studied in order to improve the grades and recoveries of zinc and indium of the zinc concentrate in the Dulong concentration plant. The experimental results have shown that copper sulfate mixed with a chemical reagent X-1 as the activator in the marmatite flotation produced a much better beneficiation than copper sulfate alone, increasing the zinc and indium recoveries of 10% and 6%, respectively, while the concentrate grades were unchanged. Also, the new activator acted well around pH 10, allowing large savings on lime consumption in the marmatite flotation. In addition, it has been found that a sufficient activated time of activator with ore slur-ry in the flotation is needed to achieve good beneficiation of the marmatite ore.

Jan 1, 2014

By L. Filippov

"Nickel is an important metal with the total global consumption of about 2 million tons per year. It is sourced from both sulfide and laterite ore, but currently laterites are becoming more attractive for nickel production due to the depletion of high grade nickel sulfide ores. Laterites are generally processed by hydro or pyro-metallurgy and therefore, pre-concentration of nickel before such processes is very important. In this paper the effect different physical methods (including flotation) on the pre-concentration of nickel in laterite ores will be discussed. The ore used in this study was a laterite from South East Asia. Nickel was upgraded using different methods such as magnetic separation, flotation and sizing. The effect of ore mineralogy on choosing the best strategy to upgrade nickel will be discussed. The findings of this project will help to unlock a substantial volume of nickel with significant value from laterite ores.INTRODUCTION Nickel is an important metal with the total global consumption of about million tons per year which has grown rapidly during last decades (Mackey, 2011). Nickel is sourced from two different types of ores, sulfide and laterite. The majority (about 70%) of the world’s nickel resources occur as laterite ores which are often complex, and low grade, and therefore expensive to treat using conventional methods (Xu et al., 2013). Today, nickel laterites are more attractive for production of nickel as the amount of high grade nickel sulfide ores has diminished (Janwong, 2012). Therefore more economic processes to recover nickel from these resources should be developed.It should be noted that nickel laterite mineralogy is complex, and nickel often presents as ultrafine inclusions in a number of mineral phases. Because of the low nickel concentration and variable distribution in these phases, effective upgrading by physical separation processes would be challenging. Researchers have tried to improve nickel laterite flotation recovery by using a number of feed preparation techniques. A summary of the nickel grades obtained using flotation and magnetic separation as reported in the literature is presented in Table 1. It can be seen that only minor nickel upgrades have been reported. Quast et al. (2015) have concluded that the complex mineralogy of nickel laterite ores makes it difficult to achieve any significant nickel upgrading by physical techniques, including flotation. They achieved 40% increase in the nickel content (from 1.0% to 1.4%) at a nickel recovery of 43% (Quast et al., 2015). Various attempts in USA, New Caledonia, India and Australia, to upgrade nickel in laterite using magnetic separation have not been successful (Quast et al., 2015). A recent comprehensive review on topics influencing nickel laterite flotation has shown that further investigations in the flotation of laterite ores are undoubtedly warranted (Farrokhpay & Filippov, 2016)."

Jan 1, 2018

By M. Zolghadri

MIBC and sodium metasilicate are used as a frother and a dispersant in coal flotation respectively. In order to study interaction between them, flotation experiments were performed on fine coal (<150 microns). It was found that if the frother (MIBC) dosage is in excess of a certain limit, it has an activation effect on the gangue minerals associated with coal. In addition, it was found that however sodium metasilicate can disperse clay slimes eliminating slime coating, but in the case of excess dosage, could intensify activation effect of MIBC, which is undesirable in coal flotation. Keywords: coal flotation, sodium silicate, frother, dispersion, activation

Sep 1, 2012