Search Documents

By Stoyan Gaydardzhiev, Michel Shengo, Pierre Kalenga

Lab-scale flotation of copper and cobalt oxidized ore from the Luiswishi deposit in the Katanga province (DRC) has been done focusing on the influence of the degree of process water recycling on metals recovery. Results have shown that at 20 % recycling rate, the recovery of copper and cobalt in the cleaner stage have been respectively reduced to 23 % and 45 % in comparison to 53 % Cu and 63 % Co if process water has not been recycled. At 10 % recycling rate however, the system could still tolerate the effect from recycling, since Cu and Co recovery has remained respectively at acceptable levels of 52 % and 60 %. In order to explain the reasons for the observed worsening of flotation results if process water was recycled at rate higher than 20 %, electrochemical investigation of the pulp has been performed. It has been established that the chemical compounds formed in the pulp when process water was recycled, do influence the sulphidization of malachite and heterogenite and impact further collector adsorption. To confirm these assumptions, the effect from thiosulphate ions presence during the sulphidization of high purity malachite has been studied. It has been found, that thiosulphate ions depending on their concentration in water induce variations in pulp properties such as DO content, pH, Es and contribute to formation of undesirable chemical compounds on mineral surface as identified by DRIFT spectroscopy.

Jan 1, 2014

By J. K. Afidenyo

Microbial pretreatment of a double refractory gold ore was investigated using a white rot fungus, Coriolus versicolor (ATTC 20869) to improve gold extraction. A series of preliminary tests were conducted to determine the amenability of the ore to fungus degradation. Pulp density, temperature, pH and retention times were the process variables considered. Both a single. Stage and two-step processes were studied to establish process conditions. During the single stage process, the ore was contacted with the fungus culture (biotic) for 3weeks at 30°C and pH 10.0. For the two-step process, the first step involves ore contact with the culture medium (abiotic) at 45°C and pH 10.0 followed by fungal contact (biotic) at 30°C. Results indicated that carbonaceous matter is not degraded but passivated by the fungus; as preg-robbing activities dropped significantly from 18.1% to below 1.0%. The single stage process resulted in higher gold recovery than the two-step process Gold ex-traction by cyanidation of the pretreated ore was 78.9% for the single stage compared with 15.0% for the untreated ore. In the two-step process, only 73.3% gold extraction was achieved. Application of the two step process conditions to a high grade flotation concentrate, resulted in 93.3% gold ex-traction as against untreated concentrate of 30.5%. The results show that the microbial pretreatment process degraded sulfide sulfur, passivated carbonaceous matter and enhanced gold extraction from double refractory gold ore and concentrate.

Jan 1, 2014

By Kumar Ranjan, Kumari A. V. Asha, G. E. Sreedhar, Banerjee R. Raja, M. Narasimha, R. Shivakumar

In this paper, numerical simulation of magnetite, medium segregation and coal partitioning have been made in a 350 mm diameter cyclone. An attempt is made to assess the nature of impairment in efficiency in relation to the increasing amount of near gravity materials in coal. The CFD model approaches the Algebraic Mixture (ASM) model with the granular option and Reynolds stress model (RSM) to resolve the air core and turbulent mixing of the medium and coal particles. The partition characteristics of the DMC were modelled using both Lagrangian & Eulerian particle tracking for particles ranging in size from 0.5 to 8 mm and in density from 1200 to 2000 kg.m-3. Lagrangian frame work based Discrete Phase model used to simulate the coal particle trajectories inside the DMC and attempted to understand the residence time of different size and density coal particles. It was observed that coal particles having density near to separation-density (having fifty percent of probability to under flow and overflow) are exhibiting increased residence time than any density particles. As expected the smaller size coal particles shows higher residence time than the coarse coal particles. CFD simulations on effect of NGM mass fraction are simulated and analyzed using ASM model including for coal and magnetite. Coal particles with high NGM content show significant effect in misplacement of coal particles towards wrong products at all relative densities. The residence time of the particles increases because of its increased interaction with near dense particles. The effect of NGM fraction on overall cyclone performance as well as detailed flow assessment in terms of residence time distribution, NGM particle concentration profiles with respect to LZVV is presented.

Jan 1, 2018

By C. Han

The analytical results of Dagushan grinding workshop primary grinding operation product show that the size fraction of -0.079mm is 32.88%, the size fraction of -0.01mm is 9.97%, the rate of -0.01mm size fraction and -0.079mm size fraction is 30.32%. It means that there is too much -0.01mm size fraction in primary grinding operation product and fall out that there will not be a better result in following operations. Several tests have been carried out to control the size distributing of the primary grinding operation product according to confirm the appropriate conditions of grinding operation. Integrate with theoretic count, grinding property tests show that the appropriate rev ratio of ball mill should be between 85% and 90% so as to get better size distributing. Based on the results of grinding property tests, the shocking property tests simulated the momentum of different diameter steel balls in the ball mill have been carried out. It showed that if want to get better size distributing the appropriate diameter of steel ball should be 110mm. The tests result shows that regulate diameter of steel ball and rev ratio of ball mill could control the size distributing. Contrast to the technical parameters of ball mill in grinding operation now, there are some significant advices are given for practice and industrial tests.

Jan 1, 2014

By Y. Foucaud, I. Filippova, L. Filippov

Flotation is the most common beneficiation route for tungsten ores, but the predominance of minerals with similar surface properties poses a real challenge. This study investigates the use of Falcon centrifugal separators for gangue minerals removal and desliming prior to flotation. A typical tungsten-bearing skarn ore (Tabuaço, Portugal) is used, containing scheelite (CaWO4) associated with dense calcium-bearing silicates (vesuvianite), fluorite, apatite and light silicates (feldspars) as gangue minerals. Two types of Falcon bowls (Falcon UF and Falcon SB) were used, prior to flotation tests with fatty acids as collectors and a combination of sodium carbonate and sodium silicate as gangue minerals depressants. This flowsheet was compared with a reverse configuration, using flotation prior to Falcon concentrator, and with a classical flowsheet, using hydrocyclone and flotation. Gravity pre-concentration and desliming with the Falcon concentrator were optimized through the design of experiments (DoE) methodology. The influences of pulp density, rotational speed, feed flowrate and fluidisation pressure (for the Falcon SB) were studied for both bowls. Results showed that the Falcon can be used as a desliming and pre-concentrating apparatus. Separation performances depend mainly on rotary speed and pulp density for the Falcon UF, whereas rotary speed and fluidisation pressure are the main parameters for the Falcon SB. With only one stage of Falcon SB, an enrichment ratio of 7.9 is obtained with a 65% WO3 recovery while 89% of apatite and fluorite are rejected, which constitutes a very good selectivity. In comparison, Falcon UF shows lower enrichment ratios, around 2.7. In terms of desliming, Falcon UF is as efficient as the hydrocyclone, while the Falcon SB is significantly more efficient. Hence, the use of Falcon SB prior to flotation improves the overall performance of the tungsten flotation route by desliming the flotation feed while pre-concentrating the scheelite. It impacts very advantageously the flotation, as most of the calcium-bearing minerals are eliminated. A Falcon SB stage prior to flotation yields a final concentrate grade of 29.7% WO3 with a recovery of only 36.8 % that should be optimized as the reagents dosages were not adapted to the pre-concentrated feed.

Jan 1, 2018

By K. D’Elia, L. D. Ogrel, O. A. Malyshev, T. I. Yushina, I. M. Petrov

"The purpose of this research is to develop enhancements in the mineral processing by flotation methods of nonferrous ores. Currently, 180-190 million tons of ore are processed by flotation in Russia. The annual processing volume of copper-nickel and copper-zinc ores exceeds 20 million tons. In the total volume of processed ores by flotation, non-ferrous ores account for roughly 35% and ores of precious metals for another 15%. The total demand of flotation reagents in Russia in 2016 was estimated at 170,000 tons. Sulfur-based collectors used in the flotation of non-ferrous sulfide ores (typically, xanthates) do not always offer sufficiently high recovery of valuable components.It has been found that reagents like DMIPEC and DK-80 improve the recovery of metals into concentrates. To identify the reasons of that higher recovery, quantum chemical calculations of the mechanism and interaction forces of DMIPEC with non-ferrous sulfides were undertaken by determining the stabilization energy of the resulting chemical complexes. It has been shown that, in the interaction of DMIPEC and DK-80 with the surfaces of sulfide minerals, ethylene and acetylene bonds act as the reaction centers, and the formation of molecular p-complexes is the result of metal-cation interactions with the surface and the flotation reagents.In the flotation of non-ferrous ores, DMIPEC and DK-80 act as selective supplementary collectors with foaming properties, and at a flow rate of 3-35 g/ton, they reduce the flotation time, and increase copper recovery by up to 3.5%, zinc recovery by up to 12%, gold recovery by up to 8-10%, allowing to increase the recovery of valuable components by 1.5-12.0%, basically this kind of reagents nearly double the flotation rate, improve the grade of the concentrate, improve the stability of the flotation process parameters, and reduce the environmental impact of flotation plants."

Jan 1, 2018

By Peter Ay, Bodo Müller, Jens Markowski, Manfred Kanthak, Florian Logsch

"Presently the global commodity situation for non ferrous-, precious- and rare metals is characterized by a strong increase in consumption and a simultaneous shortage of materials derived from primary sources. So the use of secondary raw materials gains is important due to economic and ecological reasons. Non Ferrous-, precious- and rare earth metals were detected in household waste (Municipal solid waste, MSW) for years. In MSW-treatments plants NF-metals are actually mostly separated from dried fractions. The separation of these metals is carried out with the aim of removing particles which disrupt further processing. A selective enrichment of individual non-ferrous metals has not been carried out previously. The separated fractions contain mixtures of Al, Cu, Zn, Pb, Sn, alloys, precious metals (e. g. Au, Ag, Pt) and rare metals (Ga, In, Nd etc.) along with considerable amounts of contaminations. The R&D project "NE-Rec" selectively processes the coarsely separated non-ferrous-metal-conglomerates increasing the concentration of targeted metals. Metals and metal mixtures are concentrated by sorting steps and the impurities are discharged from the process. Still contaminated precious metals are then subjected to a wet-chemical treatment. So metals can be specifically brought into solution or can be precipitated to separate unwanted components (inerts, polymers, foreign metals). Further the relevant metals will be concentrated by thermal-metallurgical processes. The technology, developed in the R&D project, enables identification, separation and processing of non-ferrous metals, precious metals and REM in household waste and transfers them into further processable individual fractions."

Jan 1, 2014

By Lina Chica, Arturo Barrientos, O. Bustamante

Hydrocyclone is a device commonly used in mineral processing industry. Underflow control plays a fundamental role in hydrocyclone operation. This affirmation supports the fact that hydrocyclone underflow has effect in some aspects of separation performance like capacity, split ratio, cut size and bypass. Hydrocyclone operation state is associated to underflow characteristics: air core formation and discharge shape. Many studies attempt to understand size separation phenomenon and the discharge influence but none of them has taken an energy point of view. This work presents the results of a mechanical energy dissipation for hydrocyclone operation from a mechanical energy balance. The experimental results related to Newtonian suspensions show that underflow energy dissipation does not control the operation because this magnitude is small compared to interior energy dissipation. However, discharge energy dissipation provides enough information to describe underflow conditions and its influence in separation conditions. In the modelling non dimensional parameters have been considered for hydrodynamic description and for geometrical and operation hydrocyclone characteristics. Energy dissipation from the continua media approximation results into a relevant concept to understand the hydrocyclone performance and improve industrial installations.

Jan 1, 2014

By V. Panayotov, M. Panayotova

"Wastewater from ores processing is often polluted by molybdate and sulfate (SO42-) ions. Sorption is one of suitable methods for removing those pollutants when presenting in low concentrations. This work reports results on adsorption of sulfate and molybdate ions on metal modified (with barium - Ba and lead - Pb) and organic reagent modified (with Hexadecyl-trimethyl-ammonium bromide - HDTMA) clinoptilolite. Zeolite’s modification with Pb, Ba and HDTMA increases its uptake capacity with respect to Mo(VI) at pH 3, with the uptake capacity decreasing in the order CL-Pb > CL-HDTMA > CL-Ba. Lead-modified clinoptilolite shows high uptake with respect to Mo(VI) in acidic, neutral and slightly alkaline conditions. The presence of SO42- in concentrations twice higher than the amount of Mo(VI) do not interfere with the Mo(VI) removal by CL-Pb. Zeolite’s modification with Ba and Pb renders it able to immobilize SO42- from water in the pH range 3-9. Kinetics of the uptake process is best described by the pseudo-first order kinetic equation. Increasing the initial concentrations of Mo(VI) and SO42- increases the removed amount of pollutants. INTRODUCTION Wastewater from copper-molybdenum ores processing is often polluted by molybdate and sulfate ions. Molybdenum (Mo) migrates easily in water and consequently the Mo polluted areas could extend for hundreds and thousands of meters (Ryzhenko, 2010). Molybdate anion is the only Mo(VI) species in natural water, i.e. at pH > 6.0. Its median freshwater hazardous concentration affecting 5% of the species (HC 5.50%) is 38.2 mg Mo/L (De-Schamphelaere et al., 2010). The marine water chronic toxicity (HC 5.50%) is assessed at 5.74 mg Mo/L (Heijerick et al., 2012). The predicted no-effect concentrations (PNEC) are 12.7 mg Mo/L and 1.92 mg Mo/L correspondingly for freshwater and marine water (Heijerick et al., 2012a). When sulfates present in drinking water in excess of 250 mg/L they cause a cathartic action (especially in children) in the presence of sodium and magnesium, and when the concentration exceeds 600 mg/L, diarrhea. When sulfate-rich effluents are discharged into the environment, they may increase the acidity of water bodies and soils (Guimarães and Leão, 2014). Because of the adverse effects to human health and the environment, limits are set for SO42- concentrations in waters and wastewaters in the range of 250 / 500 mg/L."

Jan 1, 2018

In looking to the future of mineral processing the focus is typically on improved processing units. Basically it is a search for an elusive wonder machine that could revolutionise the economy of mining: the sorter that strips 50% of the ore with only a few % loss of value; the comminution device that uses 5% of the energy while producing fully liberated particles; or the recovery device capable of producing a 99% recovery at 99% grade. These aspirations are propounded against a reality backdrop of sorters rusting in back yards, mill throughputs below design and varying by 30%, cyclones flaring and cut-sizes fluctuating, mediocre recoveries and soaring processing costs. This disconnect between aspiration and reality appears, to these authors at least, to be a mighty chasm. Moreover, it remains one over which we are expected to magically leap rather than methodically bridge. Indeed one may be forgiven for thinking that should such a wonder machine come along, taking advantage of it would be highly improbable. Questions would inevitably emerge on how to feed the correct material, how to cope with the wide variability of feeds, how to control such advanced equipment and how to handle the new product from such a machine. It is likely these questions might lie unanswered, or more regrettably, unasked. It is generally accepted that as an industry we are exceedingly unlikely to teleport from the current status quo to an entirely new reality in a single flash. It is our thesis that the probability of these magical machines materialising is remote, and even if they miraculously appeared, we simply wouldn?t know what to do with them. Rather, it is our contention, that a step change will only arise through a staircase rather than from a single giant leap. We should focus on building those steps and linking them together into a firm structure ? a workable mineral processing circuit. This paper addresses the alternative of a coherent set of modest but significant improvements, integrated to produce the step change we desire: essentially, a reduction of processing energy to below 40%, which we believe is achievable without recourse to any mystical machines. A key underlying capability to designing these dramatically improved processes, is the weaving of independent process models into a coherent circuit simulation, in order to design the new generation of mineral processing circuits. Keywords: step change, circuit design, circuit simulation, energy reduction

Sep 1, 2012

In this paper, the recovery of copper minerals and molybdenite in the rougher/scavenger banks of two separate mineral processing plants is compared with recovery in laboratory (batch) cells. A number of metallurgical surveys were conducted in two plants treating porphyry copper and molyb-denum ore. Batch flotation tests were performed on plant conditioned flotation feed slurry, in parallel with the plant metallurgical surveys. The effect of flotation feed density on recovery of copper minerals and molybdenite in the plant and batch laboratory cells was investigated. Changes in flotation pulp density had little effect on copper mineral recovery, in both plant and laboratory cells. The ultimate recovery for molybdenite, on the contrary, increased considerably when the pulp density was reduced, both at plant and laboratory scale. Recovery of copper minerals in the plant and laboratory cells was comparable, while molybdenite recovery in laboratory flotation cells was 3%~13% higher than in plant. It is hypothesised that the flotation rate of molybdenite is sensitive to cell hydrodynamic conditions (i.e. local turbulent energy dissipation) more than the flotation rate of copper. The flotation behaviour of molybdenite particles is likely to be predominantly controlled by bubble-particle collision frequency, which is enhanced in high local turbulent energy dissipation environment. For chalcopyrite, the flotation recovery is mostly determined by attachment and stability efficiencies. An increase in local turbulent energy dissipation, while increasing collision efficiency, may negatively impact on attachment and stability efficiencies. The outcomes may have a considerable impact on increasing molybdenite recovery from porphyry ores.

Jan 1, 2014

By Victor Avdokhin, Ivan Kovlekov

"Studies of the process of concentration of gold-containing sands and technogenic resources show that the main reason of gold losses is misbalance between size of gold particles and degree of roughness of mineral bed. This results in free circulation of small gold particles in pores with following washing off the particles from the bed by turbulent flows.We elaborated design of magnetic sluice, intended for improving efficiency of recovering fine gold by optimizing magnetic field of a magnetic system on the base of forming catching coat from magnetic mineralsThe magnetic sluice includes trough-shaped body from magnetic-conducting material. On the bottom of the trough, magnets are placed, and opposite poles of the magnets are oriented outwards. Thickness of the bottom is determined to be sufficient for locking magnetic lines of force of the magnets on each other. The magnets of rectangular plate shape are placed on the rough bottom, covering the whole surface or with spare areas; the magnets are placed across the trough with alteration of rows with the same pole orientation.Catching coat is formed of natural magnetic and weak-magnetic placer minerals in field of magnetic system of the sluice. Magnetic minerals, placing along magnetic lines of force, form rough coat of fluffy structure. Size of the magnetic particles is chosen taking into account expected size of gold particles, which are to be fixed on the rough coat or between the magnetic particles. Changing coarseness of particles of mineral bed allows to regulate selectivity of recovering heavy minerals.Forming artificial fleece from magnetic minerals of initial sand, increasing capacity of the bed and relative hydraulic proportionality of mineral particles of the bed provide for the most effective recovery of fine gold."

Jan 1, 2003

By Francisco Cubillos, Jorge Menacho, Cesar Gomez, Juan Rodríguez

Mineral flotation is the most used process to selectively separate particles of one or more minerals of interest. The process uses natural or induced hydrophobicity to collect particles on the surface of rising bubbles through collisions and formation of bubble-particle aggregates. Flotation machines must keep particles in suspension and well distributed, while at the same time, disperse a mass of air into a population of small bubbles. The efficiency of the separation depends primarily on the characteristics of the bubble population generated in the machine and its distribution and flow throughout its volume. The formation and separation of bubble-particle aggregates create two zones, with strong interactions between them, and with markedly different hydrodynamics conditions. A model describing two-phase hydrodynamics of the continuous and dispersed phases (frother solutions and bubbles, respectively), moving along the whole unit, is proposed. Bubble populations are characterized at the formation stage including the effect of the presence of frothers. Flow through the aggregates formation zone, where bubbles move freely and are closely spherical, is modeled using drift-flux analysis. In the aggregates separation zone, bubbles initially pack maintaining a water layer thick enough to prevent capillary forces to affect their shape. As water drainage proceeds, bubbles deform, capillary channels form, and a network of channels with a diameter size distribution develops; channels become narrower (permeability is reduced) as the distance from the interface increases. Froth hydrodynamics is characterized using models originally developed to describe unsaturated flow through porous solid particle beds. Effects of hydrostatic pressure are considered.

Jan 1, 2014

By E. V. Zelinskaya

"Mineral and industrial raw material mining and preparation make a negative impact on the environment. The main types of impact are the land resources gathering, soil and water balance disturbance, surface-water, underground space and atmospheric air pollution, as well as the vast amount of solid and liquid waste production. Considerable attention in recent decades has been given to waste recycling. The task is to maximize the use of both newly formed and accumulated solid and liquid wastes. The mining and mining and smelting enterprises industrial waters are a very promising source of secondary hydromineralic raw materials. They have high concentrations of not only calcium, sodium, but also, for example, lithium, rubidium, heavy non-ferrous metals. In general, unfortunately, we have to state that today there is no wide practice of extracting valuable components from waste enrichment, as well as processing of man-made waters to extract metals from them. The quantity of extracted components from underground, and furthermore passing waters, is insignificant. At the same time there is a tendency to increased demand for rare metals: Sr, B, Br, I. This is explained by their wide use in many industries. For example, the consumption of lithium products is steadily increasing. The obtained results showed that in the liquid phase in connection with high salt content and a significant difference in the macro- and microcomponents contents, conditions are initially created for the microcomponents selective isolation possibility. The identified conditions realization is most possible in such technological processes as cryotechnology, sorption and ion flotation. There is an urgent need to expand research in this direction and to recognize as a publicly important task the mining and industrial waste processing full-scale introduction into the practice of operating mining and processing enterprises and iron and steel companies.INTRODUCTION Mineral and industrial raw material mining and preparation make a negative impact on the environment. The main types of impact are the land resources gathering, soil and water balance disturbance, surface-water, underground space and atmospheric air pollution, as well as the vast amount of solid and liquid waste production."

Jan 1, 2018

By H. X. Yan, J. X. Zhang, F. S. Niu

"The analysis on influencing factors of hydraulic conditions in fine hematite flocculation, such as stirring speed, stirring time and axial distance of particle size and fractal dimension of floc was investigated. Furthermore, response surface methodology(RSM) has been applied according to the Box-Benhnken center-united experimental design principle to optimize parameters of hydraulic conditions as a response index to indicate the fractal dimension of floc. The results show that when the agitation speed is 900r/min, the axial distance is 2.0cm, and the stirring time is 3.0min, the particle size reaches the maximum value of 35.44µm and the fractal dimension is 1.6594. The interaction between the axial distance and the stirring speed is highly significant, but the interaction with the stirring time is not obvious. The experimental data and model predications match well, which indicates that the established model has high accuracy and practicability. INTRODUCTION With the exhaustion of iron ore resources that are easy to be mined and the vigorous demand for iron and steel, the exploitation and utilization of fine-grained embedded iron ore resources have drawn attention from the industry and the government [1~2]. Flocculation flotation is one of the effective methods for separation and recovery of fine granular minerals. In 1975, the method was first applied and succeeded in Tilden Concentrator, USA. Flocculation and desliming became the key technology of the Tilden to raise its annual treatment capacity from 4 million tons to 8 million tons at that time [3 ~ 4]. In 2008, the selective flocculation and desliming-reverse flotation technology was successfully used to treat 2.8 million tons of Qidong iron ore. Under the conditions of 28.36% raw iron grade and 98% grinding fineness -0.038 mm, the ideal index of 62.5% iron concentrate grade and 68% recovery was obtained [5]. Dr Kitchenner of the Royal College of Mining and the Ore Processing Research Group of Wallenstein Laboratory first proposed the use of flocculation to separate minerals. After that, many scholars conducted a great deal of theoretical and practical researches, but mostly they focused on chemical theories, mathematical models and selectivity differences in the flocculation process, while the research on the influence of the pulp flow state on the separation effect in the flocculation process started later [6~9]. The results show that the motion of the agitated flow field has a significant influence on the formation of flocs. The fluid morphology will change with the change of hydraulic conditions. The change of fluid morphology will not only affect the movement behavior of particles, but also change the action of chemical agents on the surface of mineral particles[10~12]."

Jan 1, 2018

By Chiharu Tokoro

Acid Mine Drainage (AMD), high acid water containing heavy metals discharged from mines, has been recognized as major cause of mine pollution. In Japan, the government spends billions of yen every year to prevent pollution caused by AMD in about 80 abandoned mines. It is widely recognized that the treatment could continue for long decades or an even century. However, costs and environmental loads are uncertain during the treatment because a predictive model for the quality of AMD, the dosage of neutralizer, and the amount of sludge that is applicable for abandoned mines with limited data has not yet been established. In this study, a two-steps predictive model for solution composition and neutralization chemical requirements of AMD in future was constructed based on the geochemical modeling. Requisite input data of the model was the past historical water quality data from AMD monitoring, such as metal concentration and pH in the solution, instead of the sample rocks as other conventional prediction methods. In the first step, solution composition of AMD in the future was extrapolated from the available historical data using geochemical simulation considering the first order kinetics for the mineral dissolution. In the second step, neutralizer dosage and sludge generation in the future was predicted based on the geochemical simulation supposing the chemical equilibrium and oxidation state for all of elements in the solution. Based on case studies of two abandoned mines in Japan, solution composition, neutralizer dosage and sludge generation were estimated. The results of this study demonstrate the effectiveness of our model for the prediction of AMD quality and chemical requirements of neutralization treatment after mine closing. The model is useful for the estimation of the neutralizer dosage and the sludge volume in abandoned mines with limited data. Keywords: acid mine drainage, predictive model, geochemical modeling, first order kinetics, water monitoring

Sep 1, 2012

By J. Finch, F. Rosenblum, McGill University

The self-heating of sulphides can be a major hazard in mining operations and concentrate handling, particularly during transportation and associated storage. Self-heating results from the oxidation of sulphide minerals and can vary from being insignificant to potentially hazardous to life and infrastructure. It is essential that there be a reliable test methodology that can categorize a given sulphide material as to its self-heating potential. By their nature, sulphide ores and concentrates are complex and variable mineral combinations making it difficult to predict their self-heating behavior a-priori based on mineralogy or with a simple "snapshot" test. Furthermore, self-heating behavior will depend on the state of oxidation of the sulphides as well as time, temperature and humidity. A review of available testing apparatuses and protocols that can be used to assess self-heating potential is presented. Each of these methodologies was examined in relation to its ability to predict the latent self-heating hazard of a sulphide material. Several of the methods were compared to illustrate their strengths and weakness. The results indicated that a number of the test protocols may produce false negative indications of self-heating potential, constituting an obvious concern to the industry.

Jan 1, 2014

By Kari Moen, John Rasmus Leinum, Jarle Hjelen, Terje Malvik

"Automatic identification and characterisation of mineral raw materials and beneficiated products are of major importance in mineral processing. However, minerals show great variety in their composition and physical and chemical properties. Industrial minerals may contain the same elements in about the same amount. In these cases backscatter electron imaging or chemical analysis are not sufficient to identify the minerals. Another problem arises when micro textures are not detectable in traditional imaging or the grain size is smaller than the X-ray spatial resolution.As a supplementary technique in these cases, application of crystallographic information by electron backscatter diffraction (EBSD) in the scanning electron microscope (SEM) may be a suitable method. By means of EBSD, diagnostic mineral information can be achieved if indexible patterns are provided.Until now EBSD has not been used frequently on geological samples for mineral and micro structure discrimination.The technique has been demonstrated on three Norwegian mineral raw materials and one Italian marble and shows that it has some advantages compared to traditional techniques."

Jan 1, 2003

By V. F. Petrov, O. D. Khmelnitskaya, V. M. Lodeischikov

"The processing of copper gold ores is one of the major issues of gold-mining industry in the beginning of 21st century. In this case, application of ammoniacal cyanidation process for this type of mineral raw materials deserves special attention. Irgiredmet Institute has carried out a wide range of studies on ammoniacal cyanidation process and evaluated the possible commercial use of this process for Russian operating plants. Copper gold-bearing ore from a current Russian deposit was studied. The content of gold and copper in the ore is 9.4 g/t and 0.4%, respectively. Based on the results of preliminary test work, a flow sheet was developed. It included gravity concentration followed by cyanidation of the gravity tailings using CIP. The flow sheet provides sufficient total gold recovery (91.5%). However, this technology has disadvantages, such as high specific consumption of reagents: 4.5 kg/t NaCN and 13.5 kg/t Ca(OCl)2 the ore and the increased gold grade in the liquid phase of the tails slurry (0.2 g/t). In order to improve cyanidation process parameters, test work on gravity tails processing using ammoniacal cyanidation was carried out. After the test work was completed, ammoniacal cyanidation flow sheet for copper gold-bearing ores was developed. Leaching conditions were optimized using recycled process solutions. Recommendations on gold recovery from the solutions and tails detoxification are given. The proposed flow sheet provides 91.5% gold recovery. In this case, compared to the conventional option, the consumption of cyanide decreases by 3-4 times.INTRODUCTION The technology of precious metals recovery from gold-bearing ores is based on cyanidation. This accounts for up to 90% gold recovery and the significant portion of silver (Lodeischikov, 1999). However, there exists the category of so called refractory ores. They are not amenable to direct cyanidation (without using additional expensive processes), or they are characterized by low indices of metals recovery and high consumption of reagents. The latter also include copper gold ores. Their deposits can be found extensively both worldwide and in Russian Federation. A feature of these ores is that they contain not only gold but also copper. It is considered not only as a valuable component but also as a harmful mineral impurity that hinders gold cyanidation, gold precipitation from the solutions by cementation onto zinc dust and adsorption onto activated carbon (CIL, CIP-processes), detoxification of cyanide bearing effluents."

Jan 1, 2018

By Bruno Miotto, Rômulo Faria, Juliano Tessinari

Water has become a scarce resource in quality. Companies in the ornamental stones sector use water intensively in their processes. Given the current situation, it is imperative to rationalize this feature that at first is related to the reduction of consumption, through no waste. Considering the importance of environmental preservation of this resource and also to comply with the legislation that governs the procedure for processing of ornamental stones, new alternatives should be available for the maintenance of current activities and promoting the development / growth of the sector on the principles of environmental sustainability and economic in future scenarios. The ornamental stones processing industries, especially for micro and small enterprises, require the implementation of a management program that optimizes the use of this feature, since the techniques individually processed operate with three basic processes dependent on water use: split blocks, polishing and finishing slabs. This technology requires a large volume of water resources and control measures involving operating recirculation water can minimize power consumption, making the company more profitable and sustainable. This is a survey of literature, associated with technical reports provided by partner companies and government agencies. This study aimed to the organization and provision of theoretical knowledge about the subject matter coupled with management practices, which may be reproduced or re-purposed in ornamental stones processing companies. It should be noted that the industry in question is lacking in technical expertise for the implementation of sustainable attitudes relevant to water reuse.

Jan 1, 2014