Search Documents

By Mohammad Mainul Hoque, Linhan Ge, Ai Wang, Geoffrey Evans, Subhasish Mitra

"Dispersed phase interactions involving bubbles and particles in the turbulent environment play a significant role in the flotation process. The conventional collision models only account for the deterministic rather than the stochastic behavior of turbulenct flow. What the bubble-particle collisions would be like remains an open problem due to the complex nature of turbulent flow. To address this research question, the present study aims to quantify the bubble-particle collision efficiency incorporating turbulence using the computational method. Multiple solid particles were released to interact with a single stationary rigid bubble (non-deformable interface). Effect of particles Stokes number, turbulent intensity (TI) and integral length scale on the bubble-particle collision efficiency (Pc) was examined. Large Eddy Simulation method (LES) was used to compute the continuous phase. Fluctuating velocity required at the inlet boundary condition was derived from Gaussian energy spectrum to generate the upstream turbulence. Discrete Phase Model (DPM) is used to simulate particle trajectory. The characteristics of turbulent flow were analyzed through Energy spectrum and energy dissipation rate. The critical initial releasing radius of the annulus, where Pc equals zero, reaches up to 1.5(Rb+Rp) under high turbulent intensity (TI) 20.48% compared to 0.23(Rb+Rp) calculated from the traditional Pc model. Pc decreases as the distance of initial releasing annulus between bubble centre increases. Pc increases as particle Stokes number increase up to 0.66. The collision efficiency for particles of St less than 0.38 is higher under TI 11.78% compared to TI 4%.INTRODUCTION To increase mineral recovery, interactions between bubbles and particles are essential. All flotation devices achieve it through introducing some level of turbulence into the system by increasing specific energy dissipation rate. Figure 1 shows three different flotation equipment, traditional floatation cell, Concorde cell and cyclonic-static micro-bubble flotation column (FCSMC), with different turbulence generation mechanisms – impeller, down-flow liquid jet and pump recirculation, respectively."

Jan 1, 2018

By A. T. Sutaone

"In the Dongri Buzurg Manganese Mine of M/s Manganese Ore (India) Ltd., high grade lumpy manganese ore required for iron and steel industries is produced through multi-stage crushing and screening. This has resulted in accumulation of 50,000 tonnes of low grade fines over the years. This production of such fines is still going on. The fines create environmental problems, like air and water pollution and siltation in adjoining fields. Besides containing lot of manganese values, they occupy large space which is very scare in mining area.The Indian Bureau of Mines under one of its statutory functions has suggested the company to explore the possibility of recovery of additional values under conservation and environmental aspects. Hence the company has sponsored a bulk sample for beneficiation studies in the Modern Mineral Processing Laboratory and Pilot Plant of Indian Bureau of Mines at Nagpur, India. The main manganese minerals present in these mine rejects have been identified as pyrolusite and psilomelane. The purpose of this study was to explore the possibility of evolving a suitable beneficiation flowsheet to obtain manganese concentrates assaying over 72% MnO2 to be used as raw material for the manufacture of dry cell batteries.The sample/material was subjected to characterisation studies in terms of chemical analysis, granulometry and mineralogical compositions. Based on these characterisation studies, the beneficiation process developed comprised of desliming, jigging and low intensity magnetic separation mainly to reject quartz, silicates and jacobsite. The manganese concentrate thus produced assayed 70.2% MnO2 with MnO2 recovery of 78% and weight per cent yield of 63.5. This natural concentrate could be mixed with the electrolytic manganese dioxide produced by the company and this blend can thus be used as a raw material for the manufacture of dry cell batteries by the end users. The paper deals with the details of test work carried out in evolving the process flowsheet."

Jan 1, 2003

In this paper High Pressure Grinding Rolls(HPGR) was utilized to pretreat CVRD southern specular hematite for enhancing the pelletization of the refractory hematite. The process parameters of HPGR, balling and firing were optimized, and the mechanism of HPGR was demonstrated by determining the surface activity by means of Blaine specific surface area tester, laser size analysis, scanning electron microscopy (SEM),X-ray diffraction (XRD), micro calorimeter and pelletability index. It is shown that the pelletization of the refractory hematite was greatly improved. The drop strength of green balls increases from 3.4 times to 13.6 times from 0.5m height while the bentonite dosage decreases from 2.2% to 1.3%.The compressive strength of roasted pellets also reaches 2500N/pellet. The mechanism of the pretreatment of CVRD southern specular hematite concentrates by HPGR is revealed that the surface activity is improved by an increases in specific surface area and the amount of micron size fractions, and higher lattice deformation and defects due to the fractures occurring inside particles during static pressure comminution, resulting in more wetting enthalpy, higher pelletability index and good property of roasting.

Jan 1, 2014

By G. V. Kalabin

"The paper supports applicability of satellite imagery at regional and local level for rapid quantitative assessment of natural environment in zones of activity of mining complex enterprises. Exacerbation of environmental problems during mineral mining and processing associated with their scale and geography of field distribution through the vast territory of our country requires constant monitoring of natural environment status, which necessitates engagement of space surveillance nowadays. It is proposed to use the monitoring of land cover and land use at regional and local level for the environmental assessment of a particular production or complex productions. You must establish the dependence of NDVI change trend with the magnitude of anthropogenic impact on the source or multiple sources of environmental pollution a particular area.. We present the results of studies of vegetation remote sensing methods in a number of territories placing mining enterprises. INTRODUCTION Ensuring a healthy environment is necessary both in untouched areas and disturbed. The condition of the developed territories should be monitored with particular attention, since the restoration of the disturbed territories requires great efforts and financial costs. More narrowly, the health of the environment (Zakharov V.M. and etc.,2001) means its quality ensuring the health of man and other species of living organisms, which includes two aspects (Zakharov V.M. and etc, 2000): - ensuring an environment conducive to human health as a biological species: - maintaining the health of the natural environment, i.e. its constituent species of living organisms and plants. The consequence is the disturbance of natural ecosystems, which determines the quality of the environment, favorable for human habitation and the state of health of the population in total determine the status of the territories where enterprises for the development of georesources are located and allow them to be ranked according to the degree of environmental danger. Without knowledge of the trajectory of ecosystem successions, it is impossible to offer adequate requirements for the technologies used to ensure the implementation of the preserved natural potential after the removal or reduction of man-made stress."

Jan 1, 2018

By S. Gerl

Since Schönert, 1980 a multiplicity of scientists have dedicated themselves intensively to the scientific investigation of wet grinding in agitated media mills. The achieved research results led to a clearly improved understanding of the comminution mechanism in wet operated agitated media mills and in consequence also to clearly more efficient machines. In contrast to this the standard of knowledge on dry grinding in agitated media mills is still very small. The practical experience from numerous plants shows however that the transferability of knowledge from wet grinding to the dry grinding regarding transport phenomena and comminution behaviour, influence of the operating parameters and also wear is very limited. In the industrial application above all the continuous mode of operation is preferred. The main problem which has to be solved in agitated media mills is minor the comminution itself, than rather the question of the trouble free material supply and material extraction as well as the cooling of the mill. The agitated media mill MaxxMill® offers an innovative concept to overcome the feeding and extraction problem with its rotating grinding chamber, the eccentrically mounted agitators as well as the eccentric flow deflector with integrated material supply. Because of the pneumatic extraction of the ground materi-al cooling of the milling chamber is not necessary. On a MaxxMill ® laboratory mill with a 5 litre grinding chamber volume extensive parameter studies were carried out to study the influence of operating parameters on the continuous dry grinding of quartz sand. The test were performed in a continuous single pass operation without classification of the final product. Apart from the influence of the throughput rate on fineness above all the influence of the agitator and grinding chamber speed as well as the grinding media size was examined.

Jan 1, 2014

By Tim Suljada, Mary Stewart, Jim G. Petrie, Damien Giurco

"The minerals industry is being challenged to reduce the amount of virgin ore that is mined, and to replace this material through the recycling of used commodity items and scrap, or by the reprocessing of waste materials. It is argued here that the existing technology base of minerals processing and refining offers real potential for handling these secondary resources. The challenge is to develop tools by which the most preferable recycling routes (both economically and environmentally) can be identified from a list of feasible alternatives, taking into account any operational constraints of these technologies.This paper describes an heuristic approach to developing the family of all technically feasible flowsheets to address this challenge, from which a preferred option may be selected according to a set of decision criteria (economic and environmental). Our approach uses conventional flowsheeting techniques of selecting flow variables and splitter functions, supported by design performance information for each unit operation. This set of design decision variables is augmented by knowledge of the suitability of a particular waste or scrap stream for a given unit operation within a flowsheet. We achieve this by comparing the composition of the scrap stream with the range of mineral streams for which the unit operation was designed initially. This is inspired by the “overlap” approach proposed by Legarth, where an “overlap” of 1 would suggest that there is high degree of compatibility between a given secondary resource stream and a primary mineral stream as inputs to a specific technology. The “overlap” concept has been extended to include information about the physical characteristics of secondary resource streams, as well as information relating to synergistic / antagonistic influences of minor elements present in the waste stream. A flowsheet which delivers a product of acceptable quality from a given secondary resource material is built up from a progression of unit technologies. The exercise is repeated to generate the family of all feasible flowsheets from combinations of acceptable unit technologies."

Jan 1, 2003

By Robinson Irarrazabal, Edison Collinao, Rodrigo de Carvalho, Patricio Davila, Marcelo Tavares

"In recent years, DEM (discrete element method) softwares, along with 3D laser measuring equipment, have become powerful tools to describe mill charge behavior, as well as forces acting on the liners of SAG mills. With the aim of contributing to streamline this application of the advanced technologies ME Elecmetal and Universidade Federal do Rio de Janeiro, UFRJ, proposed a new approach to improve the design of mill liners using elements from mechanistic modeling of grinding. The paper presents a methodology for continuous improvement of liner design, which uses information from the DEM collision energy spectra in the mill discriminated for the different components (ore and steel balls), as well as information on the breakage properties of the ore being ground. From these it proposes the concept of "effective collisions", which corresponds to the collisions that are of sufficient magnitude to cause breakage, thus allowing to discriminate from impacts that do not cause breakage either in a first impact or after repeated loading. It also tracks the collision of steel balls against the shell in order to assess their potential damage to the liners. An industrial case study is presented of a 38’ diameter SAG mill, which was experiencing challenges associated to liner breakage and low efficiency with the old liner design. Through a modification of the liner design, simulations demonstrated the potential benefit associated to reduction in ultraprojection and improvement in mill capacity. Implementation of the new design in the SAG mill was carried out, resulting in increase in daily throughput from 6 to 12%. Further, the time spent in liner change was reduced by 47% given the reduction in the numbers of parts. This operation also benefited from having no stops due to unplanned shutdowns to replace broken tiles. These demonstrate the benefit of coupling advanced computational tools to sound engineering principles in continuous improvement of liners."

Jan 1, 2014

By Pawel Strzalkowski, Marta Baszczynska, Urszula Kazmierczak

The paper presents issues related to interference of mining activities with the environment. Exploitation of mineral resources causes primarily a modification of the landscape. All of the negative impacts on environment are short-lived and last as much as it takes to exploit the raw material. After the mine closure reclamation is necessary during which all aspects that reduce harmful effects of the mining activities on the environment must be taken into account. Current ways of reclamation allow recreating natural environment, which is different from the original and enriched in diverse new values. This requires propositions of new forms of converted land development through a detailed analysis of technical, natural, planning, economic and social sphere requirements. Before making final decisions regarding selection of direction of reclamation, a thorough analysis of the key factors has to be carried out. All steps related to the implementation of the reclamation project are shown in the paper using Limestone Mine "Górazdze" located in the south-western part of Poland as an example. This paper also presents an analysis of current ways of post-mining reclamation towards agricultural and forestry landscape, along with our own suggestion for their extension in order to preserve biodiversity. For choosing optimal solutions the most relevant criteria were considered: existing natural values and possibility of their protection. Taking into account the economic and social aspects, supported by natural potentials, implementation of tourism and recreation in this area were proposed. It was shown that this proposition would not interfere with the current trends of the natural landscaping. Finally, after completion of reclamation and land development in the considered mine area, creation of a geo-park was proposed along with appearance of geotourism in the area. To illustrate the proposed forms of post-mining land development in the form of maps, an ArcGIS(ESRI) software was used.

Jan 1, 2014

By I. Blayda

The purpose of this work is to study and make comparative analysis of germanium extraction and related valuable components of the sublimates from the burning of domestic power coals (product 1) and germanium sulfide materials, which are a waste of lead-zinc production (product 2), by traditional chemical methods (distillation of germanium in the form of tetrachloride from raw and preliminary burning source) and by microbial bioleaching of sulfur-oxidizing bacteria. The dependence of the germanium extraction by chemical methods from phase composition of the initial raw materials was installed. The germanium tetrachloride extraction from products 1 and 2 were 78.50 and 19.52%, respectively. Such difference in indexes on extraction, is caused by germanium confinement as concomitant trace component to the basic phases to carriers. The share of acid-non-soluble compounds (tetragonal modification GeO2 and silikogermanaties) in the product 1 account for 21.5 % of germanium. Ratio between acid-soluble and acid-not -soluble germanium forms are 19.52 and 80.48 %, respectively, in the product 2. Our experiments have shown, that implementation of restorative firing (with addition of 30-40 % carbon at 1150 0?) of sulfide product 2 considerably impacted on the extraction of germanium tetrachloride (91.76 %) in comparison with its low enough extraction at straight distillation of hydrochloric acid (19.52 %). The results are confirmed by a set of physical methods. The results of processing the same so-called hard phase?s material (product 2) with the help of microorganisms are presented. It Has been established, that selected strains of bacteria are capable of extracting from initial raw materials not only macro components (iron, zinc, lead, manganese, aluminum, nickel), but also micro impurity of rare metals (gallium, germanium, zirconium). It is important that these metals were not extracted by traditional chemical methods (with application of aggressive conditions and heats) independently of the phase composition of the source. Almost complete extractions of germanium in solution using sulfur-oxidizing bacteria take place in the first day of the process independently of the phase composition of the source and the type strain. The results have practical significance and can be the basis for developing a unified biotechnological method of technogenic waste processing with a purpose of their sterilization and detoxification with simultaneous obtaining concentrates of valuable metals. Keywords: germanium, extraction, sublimates, bioleaching, sulfur-oxidizing bacteria.

Sep 1, 2012

By Buks Kruger

"After the milling and flotation of the platinum bearing ore, the flotation concentrate is electrically smelted in 6-in-line electric arc furnaces and the resulting furnace matte treated in Peirce Smith converters to remove the iron sulphide. The iron free (less than 1% Fe) converter matte is then granulated and sent to the Base Metals- and Precious Metals Refineries for further processing.During the smelting and converting processes two distinct gas streams are produced.The Peirce Smith converter off gas contains 4% - 9% SO2 which is treated in a conventional Sulphuric Acid Plant to produce sulphuric acid (H2SO4).The electric furnace off gas contains 0.9% SO2 and was (until September 2002) vented through a 91 meter high stack to atmosphere.Off gasses which contain less than 3% SO2 is difficult to handle and quite a few processes had been developed over the years to cope with this gas. A broad spectrum of process suppliers and technology approaches is available and the different technologies can be divided into a few main approaches i.e.Scrubbing of the off gas with an alkaline solution to produce an environmentally friendly and stable waste product which can be discharged onto a tailings dam or permanent landfill site.Physical absorption of the SO2 into a chemical solution to produce high quality chemically pure process chemicals.Catalytic reaction of SO2 with O2 to produce SO3 which is absorbed in water to produce sulphuric acid of less than 90% strength.In October 2002 Impala Platinum commissioned a Sulfacid Plant at its Smelter in Rustenburg which recovers the SO2 from the electric furnace off gasses into a weak sulphuric acid solution.The Sulfacid Plant technology is widely used in the paint pigment industry. This is, however, the first application of the technology on electric furnace off gas.The furnace off gasses contains flue dust which is removed in electrostatic precipitators. The gas exiting the precipitators normally still contains between 40 mg/Nm3 and 60 mg/Nm3 dust and passes through a quench-scrubber before entering the reactors. The quench-scrubber cools the electric furnace offgas down from ± 200 °C to 60 °C and act as a final dust removal stage."

Jan 1, 2003

By Arkady Senchenko, Sergey Rybkin, Svetlana Lagutina, Alexander Aksenov

"The application of autoclave leaching technology for sulfide concentrates containing base and precious metals is spreading nowadays. In the process of concentrate leaching silver accumulates in the forms of jarosite compounds, transforms into passive chemical state and is mostly found in solid phase. Effective technology development for silver recovery from solid phase of concentrate autoclave leaching raises the necessity for comprehensive research of silver forms of occurrence and their properties in this product. The possible form of silver presence in solid phase of concentrate from autoclave leaching is argentojarosite. This article is about the study of physical and chemical properties and structure of synthetic argentojarosite - AgFe3(SO4)2(OH)6. A method of argentojarosite synthesis has been developed under conditions simulating the process of autoclave leaching of sulfide concentrate, and includes silver dissolution in the form of Ag2SO4, Fe3+ sulfate hydrolysis, AgFe3(SO4)2(OH)6 build-up. X-ray data of synthesized argentojarosite completely correspond to those of natural mineral. The structural formula of this complex compound has been studied and confirmed. The chemical properties of synthetic argentojarosite, its solubility in acids and alkalis have been investigated. Phase changes when heating argentojarosite with the build-up of iron oxide and silver sulfate stop at the temperature equal to 650 ºC. Based on the results received the technological solutions for solid phase of autoclave leaching of concentrate have been developed with silver recovery of 95-98%."

Jan 1, 2014

By Naoki Hiroyoshi, Hajime Miki, Tsuyoshi Hirajima, Masami Tsunekawa

Acidic solutions for chalcopyrite leaching contain cupric, ferrous and ferric ions, and the oxidizing power of the solutions is indicated by a redox potential, determined by the concentration ratio of ferric to ferrous ions. This paper reviews our previous studies on the redox potential dependence of chalcopyrite leaching in sulfuric acid solutions. Leaching and anodic-polarization experiments showed that coexistence of cupric and ferrous ions activate anodic dissolution of chalcopyrite, causing faster copper extraction at the potentials below a certain value (critical potential). The analysis of the AC impedance spectra for chalcopyrite electrode indicated that a high-resistance passive layer grows on the chalcopyrite surface without cupric and/or ferrous ions, and that coexistence of these ions causes a formation of another product layer and inhibits the passive layer growth at low potentials. These results are explained by a reaction model assuming the formation of intermediate Cu2S due to chalcopyrite reduction and the subsequent oxidation of the Cu2S. The critical potential corresponds to the redox potential of the Cu2S formation and the predicted values matched with the experimental results. Catalytic effect of silver ions on chalcopyrite leaching was also discussed based on experimental results and the above model.

Jan 1, 2003

By Carlos Collado, Oscar Jimenez, Francisco Diaz, Rodrigo Bernal, Carmen Salinas

Water is a strategic resource for the mining industry. The rising cost has forced the industry to become more efficient in their use, reduce and recycle waste as much as possible. The importance of having a reliable water balance is increasingly urgent, because the resource is scarce and vital to the sustainability of human life, animal and ecosystem. Conventional flowmeters can suffer disruptions or failures by corrosion, fouling, presence of elements in the water as acids, salts and suspended solids. Use of radiotracers is advantageous to determine fluid velocities that are transported through pipes, as they are detectable by means of the radiation emitted, the same way for surface flows, such as natural watercourses and drainage from tailings dams, fluorescent tracers are those with the best advantages. For velocity measurements in pipelines a Iodine-131 tracer solution, around 5 mCi was injected into the suction of the pumps. The technique used is the transit time between detectors at known distances and determining the time of passage of the radiotracer. For measurements of surface fluxes using the fluorescent tracer Rhodamine WT by tracer dilution technique, injecting the tracer at a constant rate and measuring it known concentration diluted downstream. This work has been performed in Minera Los Pelambres, located in the IV Region of Chile, measuring the flow rate pumped from 12 pools with 1-7 pumps operating, obtaining speeds of 0.56 to 2.62 m/s. In pumping wells three facilities have been measured at speeds of 0.111-0.223 m/s, plus six surface flows with flow rates of 8.45 to 357.2 L/s.

Jan 1, 2014

By Markus A. Reuter, Jacques J. Eksteen

"The modelling of bath type furnaces tends to be either fundamental in nature or total empirical ""black box models"". While models of the first kind are robust, they tend to lack accuracy, in cases where they are to be used for process control, and may take an overly long in development time. On the other hand, black box models tend to lack robustness of prediction for all circumstances and tend to be limited to interpolate based on historical data. While this may very often provide short-term accuracy, the models may have problems with stability in the long term. Moreover, the model structure may not reflect any of the fundamental properties of the system and remains opaque to fundamental analysis. The aim of the model development is in obtaining a model that have robustness, high accuracy, a short development time and which is adaptive to a changing environment. The models are specifically developed for on-line decision support or control of furnaces. The modelling approach is evaluated for a chromite bath smelting furnace. The role of systems analysis, mass balance smoothing, thermodynamic analysis are integrated into one generic algorithm for bath type furnaces. Not only are fundamental process relationships such the mass and energy balances satisfied through a scientific method of data reconciliation; the proposed modelling approach allows adaptive prediction, the first step towards predictive control or metallurgical decision support.It is shown that neither an ARMAX model only, nor a purely equilibrium model only, could predict the dynamics of the process very well. However, a combination of the two approaches more than doubled the accuracy as measured by the R2. It was noted for carbon dissolved in the alloy, that the improvement in R2 in using a hybrid modelling approach was more than the sum of the R2 of the individual traditional approaches. Similar improvements in modelling performance were noted for all other species.It shows further that process dynamics may totally overshadow the effect of thermochemical equilibrium (even when the thermochemical equilibrium prediction includes the recycled alloy and slag heels as additional feeds). The exclusion of process dynamics therefore leads to erroneous results."

Jan 1, 2003

By Hiroshi Sasaki, Herman D. Mendoza

"The surface-chemical property of nickel slag fiber was modified in aqueous media in order to act as an active and efficient collector of colloidal amorphous silica from geothermal effluent. Colloidal amorphous silica (0.05 µm) from geothermal wastewater causes operational and ecological problems. It clogs geothermal pipes and waterways, and when disposed to the environment poses hazardous effects on both the flora and fauna ecology. Because colloidal amorphous silica is extremely fine and remains in suspension in aqueous media, conventional solid/liquid processes to remove colloidal silica from its bulk liquid are rendered ineffective.A rapid separation technique is then developed to remove effectively amorphous colloidal silica from its bulk liquid by attaching the extremely fine particles of silica onto a nickel slag fiber coated with magnesium hydroxide, Mg(OH)2. The nickel slag fiber has the following characteristics: a high surface area and predominantly possesses negative charge in aqueous media with an iso-electric point at pH ~2.5. When soaked and saturated with Mg(OH)2 solution, the surface of the nickel slag fiber becomes coated with fine and compacted Mg(OH)2 precipitates. This modifies the surface- chemical property of nickel slag fiber transforming the negatively charged surface into a positively charged surface in aqueous media with an iso-electric point of around pH 11.8, which corresponds to the iso-electric point of Mg(OH)2. When geothermal effluent containing negatively charged colloidal amorphous silica particles (i.e.p. of silica is pH 2) is passed through a column-bed packed with surface-chemically modified nickel slag fibers under natural pH conditions, the colloidal amorphous silica particles are recovered by attachment onto the surface of the surface- modified nickel slag fiber. The recovery of colloidal amorphous silica by attachment is 97-99%, resulting in the production of a relatively clean and silica free output. Aluminum hydroxide, Al(OH)3, was also used to modify the surface –chemical property of the nickel slag fiber. In the same way, it also exhibited a positive response with the collection of colloidal amorphous silica from its bulk liquid, but yielding a lower recovery of 90%. This may be attributed to the lower surface potential and iso-electric point of pH 9.3 for Al(OH)3. The separation process was evaluated and analysed using existing potential energy theories. Figure 1 shows a micrograph of the surface of an unmodified and the Al(OH)3 –modified surface of nickel slag fiber."

Jan 1, 2003

By Sanggono Adisasmito

"The quality of the higher education in Indonesia is being improved by implementing a program financed by the World Bank under a project named QUE (Quality for Undergraduate Education). The investments are provided to selected study programs through a competitive selection process. The grant finances staff development, the purchase of equipments, textbooks, consumables, technical assistance, and incentives for outstanding faculties such as teaching grants, project grants, lecture note awards, and educational policy studies. These additional investments are provided to produce chemical engineering graduates that will compete beyond the national market.Chemical Engineering Department of Institut Teknologi Bandung in Indonesia has been selected to receive the QUE grant beginning the year 2000 and ending the year 2004. The department is actively involved in the mineral processing issues, particularly in the aspects of energy supply and the environmental protection. The activities are distributed in different laboratories and areas of expertise, such as: thermodynamics and utility systems, process equipment, chemical reaction and catalysis, microbiology and bioprocess engineering, process control, ceramics, as well as polymer and membrane technology. The main objectives of the QUE project are to improve the undergraduate program in the following aspects: Relevance, Academic atmosphere, Institutional management and commitment, Sustainability, as well as Efficiency and productivity, or abbreviated as RAISE. At the end of every fiscal year, the progress of the program is evaluated to measure the effectiveness of the project.The achievement of the QUE project objectives were assessed using performance indicators developed during the program design. There are six indicators to measure the performance of the individual program of study, such as: (1) Admission Test score, (2) average students' Grade Point Average (GPA), (3) average graduates' length of study, (4) graduates' waiting time before getting first job, (5) Test of English as Foreign Language (TOEFL) score, (6) Graduate Record Examination (GRE) score. Essentially, the RAISE evaluation criteria will be used to perform three main functions, such as (1) to measure the achievement through the six quantitative performance indicators, (2) to support the progress of evaluation and reporting throughout the implementation of the program, (3) to provide a universal framework for qualitative evaluation."

Jan 1, 2003

By V. Panayotov

Flotation practice usually uses the Sheridan-Grizvold selection method, where zinc minerals are activated by addition of copper sulphate and depressed by addition of sodium cyanide, ferrous sulphate, zinc sulphate or various mixtures of these reagents. The method is suitable for the flotation of sulphide ores, which, do not bear precious metals, such as silver and gold. When classical technology with cyanide is applied to depress zinc minerals, the precious metals, which are contained mainly into lead minerals, are dissolved into the solution, which represents a technological loss. In order to avoid this process, we have made use from the knowledge on the semiconducting properties of lead and zinc sulphide minerals. We have changed the surface charge of minerals by means of an electrochemical impact realized by direct current application and specially designed set of insoluble or semi-soluble electrodes. Thus, flotation separation of lead and zinc sulphide minerals was achieved, at increased recovery of lead, zinc and silver. The technology proposed was implemented in a Bulgarian flotation factory; it worked over 5 years providing significant, positive economic, technological and environmental impact. Silver recovery was increased by 0.8-1.0 %, and lead and zinc recovery was increased by 0.8-1.0 %. The technology is easily controllable and adaptable to raw materials and parameters of the technological process. It can be paid back for 6-8 months after the implementation. Keywords: lead-zinc flotation separation, electrochemical impact

Sep 1, 2012

By Yuki Tsunazawa, Shuji Owada, Kazuki Tahara, Shinobu Ogino, Chiharu Tokoro

"Printed circuit boards (PCBs) are an important constituent of waste electric and electronic equipment (WEEE), and contain many electronic components with valuable, hazardous or both materials. Recycling of PCBs is an important subject not only from the treatment of waste but also from the recovery of valuable materials. Demand for rare earth metals is expected to accelerate because of their growing use in next generation high technologies. Since some of these metals are concentrated in a specific electronic component, for example, Ta in capacitors, a special and selective grinding such as parts detachment from the board is effective for the recycling of a part of rare metals. However, direct computer simulation method to investigate a comminution/detachment process of PCBs has not yet been established. In this study, our objective was revealing the mechanism of breakage phenomena in comminution / detachment process of PCBs using computer simulation. A special and selective grinding using an agitation mill promoted the removal of components from a PCB by detachment and was an effective method for the recovery of rare metals. Simulant PCBs on which some capacitors were solder-mounted were used for the comminution test using drum type mill with agitator. To describe this mechanism of the parts detachment process, a computer simulation using discrete element method (DEM) was conducted. Although only an indirect simulation using the spherical particle model was possible for part detachment and board breakage, the particle-based rigid body model could directly represent the behaviour of PCBs. Simulation results successfully corresponded to comminution experimental results."

Jan 1, 2014

By Zhongxue Li, Cuiping Li, Xiaoyun Hu, Yiqing Zhao, Huaying Wang

"Under the auspices of World Federation of Engineering Organizations’ Committee on Engineering and the Environment (WFEO-CEE) and Society for Mining, Metallurgy and Exploration (SME) Task Force on Sustainability and Mining (TFSM), and aimed at helping raise global understanding on and promote capacity building of risk management, this paper presents a framework and prototype of toolbox or knowledge warehouse for facilitating the application of risk analysis, mitigation and management techniques (RAMT) in the mining and minerals sector. The conception, design and implementation of the intended system of knowledge warehouse of risk analysis, mitigation and management techniques (KWoRAMT) are outlined. The system architecture of KWoRAMT is based on a browser/server (B/S) structured platform with web oriented interfaces and composed of data base, knowledge warehouse, searching mechanisms, and risk assessment methodologies. The knowledge sources for KWoRAMT will come from the TFSM expertise and Internet, including laws and regulations, codes of practice, standards, guidelines and best practices. The functions and outcomes of KWoRAMT consist of guided navigations with web links, categorized risk tools, annotated best practices with cases, and integrated risk approaches and solutions based on typical risk methods. Risk categories include those impacting on mine safety, mine occupational health, and mine community environment throughout the whole of mine life cycle from exploration, construction, and exploitation and processing to post-mining closure. Mining associated hazards will be identified and linked by vulnerability onto risk receptors through pathways. Risk management techniques for assessing impacts and consequences of mining induced hazards will be categorized with their pros and cons or strengths and weaknesses. Best practices and significant cases including experiences and lessons with problems, solutions, and recommendations on how solutions would be derived will be illustrated. Integrated risk approaches based upon typical methods will be developed for alternatives and actions."

Jan 1, 2014

By Paul W. Cleary

"Particle scale simulation of industrial particle flows using DEM (Discrete Element Method) offers the opportunity for better understanding the flow dynamics leading to improvements in equipment design and operation that can potentially lead to large increases in efficiency, throughput or product quality. DEM has been used for modelling many industrial applications, particularly milling. This includes ball and rock motions and power consumption in ball mills, AG and SAG mills, vibrational segregation, flows in rotating drums, operation of dragline excavators and hopper flows. In mineral processing, DEM has been concentrated on mills because of their critical importance. However DEM also offers the opportunity to improve many other parts of mineral processing operations. These areas often do not receive the attention that the key comminution equipment commands, but can become critical when they fail or under-perform. Importantly their assessment/improvement using DEM is often much more feasible because of smaller problem sizes and the absence of poorly understood physics such as breakage. In this paper we describe DEM simulations of four important pieces of non-comminution equipment that are commonly found in or near mineral processing plants (these are shown in Figure 1):"

Jan 1, 2003