Search Documents

By Jeffrey C. Evans, Daniel G. Ruffing, Hejintao Huang

Soil-bentonite slurry trench cutoff walls are the most common type of vertical cutoff wall used in the US for seepage control and for passive control of contaminant migration at environmental sites. Design considerations are often limited to constructability considerations and a target hydraulic conductivity. With design-build contracts common, the backfill design is often left to the contractor. As a barrier soil, the hydraulic conductivity of bentonite slurry wall backfill is typically required to be equal to or below 1x10-7cm/s. The importance of stress state upon the hydraulic conductivity as well as the expected stresses are both established in the literature. Grain size distribution of the base soil and bentonite content both affect compressibility and hydraulic conductivity. This paper describes the results of studies undertaken to evaluate the interrelationships between compressibility, hydraulic conductivity, grain size distribution, and bentonite content. Three base soils were used representing a range of soils found on typical construction projects. Using these base soils, mixtures containing a range of dry bentonite contents from 0% to 5% were prepared to a slump consistent with field practice. The compressibility and hydraulic conductivity were measured in consolidometers adapted for falling head permeability tests at the end of each load increment. These experiments yielded the relationship between effective stress and hydraulic conductivity as well as consolidation characteristics including time rate of consolidation and coefficients of compressibility. The experimental results are then used to indirectly evaluate stress development and to assess the time needed for consolidation. The findings show a substantial decrease in hydraulic conductivity as effective stress increases, regardless of base soil type and dry bentonite content, a relative insensitivity of stress development to backfill compressibility, and a wide range of values for coefficient of consolidation depending upon backfill mixture and stress level.

Jan 1, 2016

By Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan, Joseph Toth

The difficulty in material characterization and the erratic response of cemented soil layers, such as caliche in the Las Vegas valley, creates challenges for practicing engineers to reliably predict the response of deep foundations. The focus of this paper is the numerical prediction of axial response in drilled shaft foundations, which are commonly used in infrastructure projects (i.e., bridges and tall buildings) in Las Vegas, NV. The prevalence of hard caliche layers with variation in the degree of cementation add to the complication in numerical modeling. In this study, the applicability of two existing t-z models, developed for Florida limestone and soft rock, was evaluated based on numerical simulations of three bi-directional load tests conducted at caliche-dominant sites. The corresponding top-down load tests were also simulated for further assessment. A MATLAB-based finite-difference program, NVShaft, has been used to implement the mentioned t-z models in axial load analysis. Complexity originating from drilled shaft construction and the interaction with caliche during one axial load test resulted in a stiffer predicted response compared to measure data. For the other two load tests, both t-z models produced comparable load-displacement responses. It was observed that the t-z model for Florida limestone predicted relatively stiffer responses and higher drilled shaft capacity.

Sep 8, 2021

By Leena Korkiala-Tanttu, Noora Lindroos, Juha Forsman

"Construction works at the Helsinki city sea shoreline requires dredging and handling of contaminated sediments. Most of these soft dredged sediments are regarded as too poor quality material for earth construction purposes. Mass stabilization technology has been applied to improve the technical and environmental properties of the dredged sediment in order to utilize the material in construction. The treatment site presented in this article is placed in the West Harbor where the dredged sediments are disposed in basins, mixed with binders by mass stabilization and transported to utilization sites. The volume of these basins is about 90 000 m3. So far these basins have been used three times during the years 2011-2014. The most applied binder has been cement. Its high price and carbon footprint have encouraged use alternative binders. Other used binder materials include fly ash and end product of desulphurization from coal combustion, and fly ash from combustion of Estonian oil shale. The technical and environmental properties of stabilized sediments have been studies in the laboratory and in situ thoroughly. Some properties of the stabilized sediments which have been studied are: compression strength, modulus, hydraulic conductivity, leaching of contaminants, etc. The leaching test results show that heavy metal leaching is very low with all binder materials tested.1. INTRODUCTIONContaminated marine sedimentsMarine sediments in the coastal areas are often contaminated as a consequence of industrial and port activities, as well as the influence of cities located there. Construction activities and reclamation of shore line require dredging and handling of contaminated sediments since the level of contamination inhibit dumping of dredged sediments into the sea. Based on their technical properties, most of these dredged soft and watery sediments (clay, gyttja, etc.) are regarded as too poor quality material for earth construction purposes. Economic, sustainable and environmentally safe management of contaminated, dredged sediments is a key issue in many construction sites.In the City of Helsinki, mass stabilization technology has been applied to improve the technical properties of the dredged sediments in order to utilize the material in construction. Owing to stabilization / deep mixing / solidification, also the contamination is encapsulated in a monolithic solid of a high structural integrity. Thus, contaminants migration is restricted by the decreased surface area exposed to leaching.The treatment site presented in this article is placed in the West Harbor (a place of Helsinki called Jätkäsaari) where dredged sediments are disposed into stabilization basins, mixed with binders by mass stabilization and then transported to final utilization sites. The location and principle of these basins is presented in Figures 1-4. The overall volume of these four stabilization basins is about 90 000 m3."

Jan 1, 2015

By Ramin Motamed, Farshid Ghazavi, Joseph A. W. Toth

"Post-disaster reconnaissance of areas affected by earthquakes has documented extensive damage to buildings with shallow foundations located in liquefaction-prone areas. Currently, estimation of liquefaction settlement is based on empirical correlations that evaluate settlement in the free-field environment and are based on one-dimensional consolidation. However, observations have shown that liquefaction settlement under buildings can be considerably greater. This research is based on a series of 1- g shake table experiments using a transparent soil box to reproduce liquefaction-induced building settlement. Building settlements were evaluated using a scaled model of a building foundation representing a 1-2 story building. Comprehensive parametric study was carried out to establish the effects of several parameters on free-field and building settlements such as building width and thickness of liquefiable soil layer. The experiments utilized accelerometers and pore-water pressure sensors to monitor ground accelerations and buildup of pore-water pressures in both the free-field and model building footprint. Results of these experiments are compared to available centrifuge tests and field observations and conclusions are drawn with respect to the potential scaling effects. Lastly, this paper discusses the feasibility of installing helical piles as a mitigation strategy to reduce the building settlements by presenting some of the exploratory experimental data obtained from this series of 1-g shake table tests.INTRODUCTIONThe 2010-2011 Canterbury earthquake sequence and the 2011 Great Tohoku earthquake are some of the most recent examples where large numbers of low-story structures sustained damage resulting from liquefaction-induced settlements. This damage has commonly been observed in residential and commercial areas developed over loose, unconsolidated and saturated coarse grained soils resulting from both natural and man-made deposits. Damages incurred from the 2010-2011 Canterbury earthquake sequence occurred in the largely unconsolidated fluvial environment bordering the Avon River in Christchurch (Henderson 2013). Similar damage was also incurred during the 2011 Great Tohoku earthquake where liquefaction of soils occurred in both young alluvial deposits and fill materials (Ashford et al. 2011). Figure 1 presents typical modes of failure to structures resulting from the effects of liquefaction. Current practices in evaluation of liquefaction settlement rely on empirical correlations (Tokimatsu et al. 1987; Ishihara et al. 1992) developed for liquefiable soils in the freefield environment (Dashti et al. 2010a). However, recent observations of the performance of foundations suggest that settlement of rigid shallow foundations in liquefiable soils are commonly greater than those predicted in the free-field. Therefore, new correlations should be developed to better predict the degree of settlement of shallow foundations in liquefiable soils. Current research is beginning to focus on the mechanisms of settlement during liquefaction in regards to confining stress, pore-water pressure and shear stress induced from foundations (Dashti et al. 2010b)."

Jan 1, 2016

By Anahita Modiriasari, Benjamin S. Rivers

Measurement while drilling (MWD) is a subsurface exploration technique associated with real-time and continuous monitoring and recording of drilling data during the drilling process. This technique can be used for underground investigations to differentiate ground strata, detect the presence of fractures and voids, and evaluate geological features and mechanical properties of geomaterial. When MWD is used for geotechnical investigations, it can improve site characterization, identify variable conditions, improve design and construction, lead to shorter project delivery times, reduce the cost and risks associated with limited subsurface data and geotechnical uncertainties, and maximum return-on-investment. Given these benefits, MWD is gaining attention among transportation agencies and the geotechnical industry. Federal Highway Administration’s (FHWA’s) innovation deployment program “Every Day Counts (EDC-5)” includes the implementation of Advanced Geotechnical Methods in Exploration (A-GaME), which aims to implement effective, underutilized subsurface exploration methods, including MWD, in U.S. practice. This paper provides an overview of the MWD technology for geotechnical site investigations and presents a case history where MWD was employed to design deep foundation for the construction of a building in Massachusetts. The advantages of this technology for risk reduction and project cost and time saving are also discussed.

Oct 1, 2022

By Donald A. Bruce

"The Deep Mixing Methods (DMM), in their current forms, have been employed in the United States since 1986, although an earlier version had seen service from 1954. The earlier developments were strongly influenced by practices in the Nordic countries and Japan, while by the late 1980’s several DMM systems had been developed in the U.S. itself. Since then, DMM has continued its evolution, principally via the challenges of a series of large, landmark projects, but also via distinct, significant technological advances. This paper highlights the key points in the history of DMM in the U.S., and provides an overview of the different methods currently in use.IN THE BEGINNINGIt is a common misconception that the history of applications of the Deep Mixing Methods (DMM) in the United States dates from 1986 when SMW Seiko Inc. — a subsidiary of Japan’s Seiko Kogyo Company — was established in the Bay Area. However, the author believes that Intrusion Prepakt Co.’s patented MIP (Mixed in Place) system had been used, albeit sporadically (about 30 projects are recorded), since 1954 (FHWA 2000, 2001). Ironically, by 1961 this single auger method had been extensively used under license in Japan for excavation support and groundwater control — by the Seiko Kogyo Company. By 1972, the original MIP technique had been succeeded by more advanced Japanese methods, involving multiple augers. Intrusion Prepakt have long since become defunct.The first systematic studies of contemporary Deep Mixing Methods in Japan began in 1967 when the Port and Harbor Research Institute of the Ministry of Transportation began laboratory testing using granular and powdered lime for treating soft marine soils. Fundamental studies continued through the early 1970’s, by which time the development of industrial scale equipment was well advanced, having its first application on a marine trial near Haneda Airport. Coincidentally, laboratory and field research also began in 1967 in Sweden (“Swedish Lime Column Method”) for treating soft clays using unslaked lime. Reportedly the progenitor was a Norwegian, Kjeld Paus, who had made observations on fluid lime columns in the U.S. It would seem that developments in Japan and the Nordic countries proceeded independently until 1975 when the technology leaders from each group (Broms and Boman; and Okumura and Terashi, respectively) presented their — very similar — findings at a conference in Bangalore, India. Limited technical exchanges ensued thereafter.Whereas the Nordic developments continued to focus on the use of dry reagents (cement and lime) and relatively light equipment compatible with operating on and in very soft clays and organics, the Japanese progressed into the use of fluid reagents (cement-based grouts) and heavier equipment for both marine and land-based projects. Thus, by 1986, there were a large number of proprietary (wet and dry) DMM systems in Japan, and a rapidly growing market already by then accounting for over 12,000,000 m3 of ground treatment."

Jan 1, 2015

By Rick Piovesan, Pramod Rao, Nihal Bohra, Mark Wahler

"This paper discusses the approach followed for the geotechnical design of 355 mm and 457 mm diameter driven open-ended steel pipe piles used for a gas plant at a green field site in Pilbara region in Australia. The principal bearing layer at the site comprises of calcareous Red Bed soils and weak rock, which is the typical geology along a significant length of the northern Western Australian coastline with carbonate content up to 70%. The uncertainty associated with the mechanical behavior of the calcareous soils and cemented soils (weak rocks) presented design challenges in the selection of appropriate pile design method and design parameters for pile capacity estimation during Front End Engineering Design (FEED). The American Petroleum Institute (API)-based design methodology was adopted. The representative design parameters for the Red Bed weak rock were established by treating the weak rock as clay with undrained shear strength as one-half of the characteristic unconfined compressive strength (UCS) value. Both statically load tested and CAPWAP (Case Pile Analysis Wave Program) estimated ultimate axial pile capacities on 25 early pre-production indicator piles demonstrated that the API design methodology for siliceous soils provides reasonable prediction of axial pile capacity in the red bed soils/weak rock and no reduction to API computed axial capacity due to carbonate content is warranted. The results also demonstrated that penalizing axial pile capacity solely based on carbonate content is not appropriate.IntroductionA gas processing facility was proposed to commercialize the gas reserves located 130 km offshore from the north-west coast of Western Australia (WA). The project site is a green field site located in the Pilbara region along the northwest coast of WA. Specific information regarding the site has been withheld due to confidentiality reasons. The site layout is shown in Figure 1.The site comprises low-lying tidal flats, clay pans and sand dunes covered with low scrub. The onshore site levels vary from elevation 1 m to 10 m AHD (Australian Height Datum), with the largest proportion of the area (excluding sand dunes) between elevations of 1 m and 3 m.The onshore facilities are to comprise a liquefied natural gas (LNG) plant site, a construction camp, the land-based portion of the materials offloading facility (MOF), roadways, and borrow pit areas.The existing ground levels within the process train area, where pile load testing was performed, vary from over 7 m AHD where the summits and peaks of the central dune exist to typically 1 m to 2 m AHD towards the east and west edges of the dune. The proposed finished grade for the process train is set at 7 m AHD."

Jan 1, 2015

By Camilo A. Alvarez, Stephen K. Harris, Brian R. Zuckerman, Philip J. Meymand, Danielle M. Steinmetz

"The sleek new air traffic control tower at the San Francisco International Airport stands at 221 feet tall and is set to replace the existing air traffic control tower by 2016. This aluminum-clad, torch-like structure and three-story Integrated Facilities Building at the base are situated between Terminal 1 and Terminal 2 adjacent to the tarmac. Berkel & Company Contractors, Inc. and Simpson Gumpertz & Heger Inc. worked in conjunction with structural engineers from Walter P. Moore Engineers and Consultants, geotechnical engineers from URS Corporation, architects from Fentress Architects, and general contractors from Hensel Phelps Construction Company on the performance-based design of a foundation to support this critical facility, which is located in a high seismic zone and situated on the very soft soil of the San Francisco Bay margin. With the loading demands and performance criteria established and Young Bay Mud thicknesses ranging from 44 to 47 feet thick across the site, the design team employed a total of 214 24-inch diameter Auger Pressure Grouted piles, which were drilled into the underlying Franciscan Formation as deep as 148 feet below existing grade. Pile reinforcement included full-length confined cages.The piles were designed to resist Maximum Considered Earthquake axial demands as high as 1,400 kips in compression and 700 kips in tension. The performance-based pile design included verification of shear capacity under double-plastic-hinge flexural mechanisms, verification of pile ductility via non-linear moment-curvature analyses, and consideration of curvatures due to kinematic as well as inertial loading.The team implemented an extensive pile load test program including a full-scale static compressive load test on a sacrificial test pile and five non-destructive high-strain dynamic load tests, four of which were performed on indicator piles that were later used as part of the foundation system. These piles were monitored with extensive embedded instrumentation throughout their length, including strain gauges and accelerometers."

Jan 1, 2017

By David Wilshaw

Continuous Surface Wave (CSW) testing has been the “next big thing” in ground characterization for the last 25 years. The technique uses surface geophones to measure the speed at which Rayleigh waves (generated by a vibratory source) travel through the ground over a range of frequencies. The velocity at which surface waves travel through the ground is directly related to ground stiffness; the velocity of shorter wavelengths is influenced by the stiffness of shallower soil layers, while the velocity of longer wavelengths is influenced by the stiffness of deeper layers. Measuring the surface wave velocity over a range of frequencies, therefore, allows a stiffness / depth profile to be produced. Using the small-strain stiffness data measured by the CSW technique greatly improves the accuracy of simple limit state analyses; the data are also of sufficient quality for use in Finite Element modelling. Nonetheless, the technique has suffered from a perception of high cost, low productivity, and poor repeatability. An improved Advanced Continuous Surface Wave (ACSW) testing system has been developed by Ground Stiffness Surveys in the United Kingdom, has been deployed there commercially for several years, and is now available in the United States. ACSW uses an automated electronic control system that generates vibrations (from a purpose designed and manufactured portable seismic “shaker”) at different frequencies, measured across a 3m (10-foot) array of geophones, linked to a robust data acquisition and analysis software package. The range of applications in geologic and geotechnical site characterization includes rapid preliminary non-intrusive site assessments (utilizing published soil correlations); stiffness profiling to detect discrete layers (such as a variation in rockhead); average stiffness profiling for earthwork or ground improvement control testing, Working Platform stability assessments, foundation settlement analysis, rock quality and rippability assessments, and void detection.

Oct 1, 2022

By Shawna Munn, Nadir Ansari, Allison Bennett

"This paper outlines how specification driven design has made Toronto Area transit infrastructure projects more expensive than similar private projects, and provides a case study of the results of an excavation at Launch Shaft 1 (LS1) for the Eglinton Crosstown Light Rail Transit project in Toronto, Ontario. The paper will describe the impact specification driven design parameters can have on design economy, constructability, and schedule and will suggest an alternative approach utilizing the Observational Method. As a result of the initial specification based design, Isherwood was retained by both the General Contractor and the Specialty Excavation Shoring Contractor to provide value engineering leveraging the Observational Method to improve constructability and construction schedule. By using well known, accepted design methods coupled with local experience in lieu of the specified design pressures and parameters, the redesigned bracing scheme reduced construction cost and schedule. This excavation case history can be a lesson learned for future transit projects.The City of Toronto has been developing its transportation network since the mid 1800’s. “Canada’s First Subway” along Yonge Street opened in March 1954 (TTC 1954), with a few additions to the subway network through to the 1980’s. The following two decades marked a long period of slow development due to recessions, budget cuts, and politics along with several cancelled projects. To fill the gap left by years of underfunding, several new transit projects are now under construction in the city as a part of Metrolinx’s $50B, 25 year, “The Big Move” initiative (Metrolinx 2013). The work on these types of infrastructure projects is highlighting a different and developing challenge within the tendering and design specification structure we will call Prescriptive Specification Design (PSD).PSD is a method used within contract specifications to control design risk on a project by applying conservative design methods, factors of safety, or other parameters to make a “fool proof” design. It is akin to requesting a colouring by numbers approach from a painter. There are inherent risks of using this method of tendering a project including increased project costs, longer construction schedules, and decrease of overall project economy. In PSD, the Owner “owns” all of the design risk on a project, including any additional costs due to changed site conditions. However, the Contractor commonly “owns” the risk of any deviations from the design specification they pursue, therefore making any improvements to the design, cost, or schedule less desirable from the Contractor’s point of view. The impact of this type of strict specified approach to design has been seen in transit infrastructure projects in the Toronto area. Figure 1 outlines the range of specified AEPD design pressures as a function of excavation height (H) specified for use in Toronto underground transit projects since the 1970’s to present day. A clear trend can be seen with respect to increased design pressures specified. The ranges shown for each project are intended to account for the potential differences in soil conditions for the highly overconsolidated glaciated soils in the Toronto area. The graph also highlights the typical range, in blue, for the industry practice in Toronto for comparison."

Jan 1, 2017

By Sarah Ramp, Daniel V. Cacciola, Justin Labrozzi, Shafiq I. Siddiqui, Faisal Ahmed

"Construction of embankments up to 34 ft in height for twelve ramps and roadways needed for the New Jersey Turnpike Interchange 14A project required ground improvement. The subsurface conditions, consisting of up to 30-ft thick layer of highly-compressible peat and organic soils, would induce up to 8 ft of primary and 4 in. of secondary consolidation settlements to the embankments over a long period of time. Innovative ground improvement solutions were needed to meet unique challenges posed by the poor subsurface conditions, space and existing utility constraints, aggressive construction schedule, and massive size of the project. A variety of ground improvement techniques were utilized in six different zones of the embankments to limit settlements and ensure stability of the embankments. These techniques included preloading with surcharge and prefabricated vertical drains (PVD), load balancing using light weight fill, and concrete column rigid inclusions (RI). Additionally, augercast piles with load transfer platform were used under an existing bridge with low vertical clearance. An innovative approach consisting of preloading with surcharge and PVDs followed by installation of RI was needed in one of the six embankment zones with the worst, i.e., very soft, soil conditions. The design of the RI was performed by a specialty ground improvement contractor (SGIC) using Plaxis 2D and 3D softwares. The performance of the ground improvement systems was verified and monitored by load tests and instrumentations. This paper presents details of the ground improvement design, construction, monitoring results, and lessons learned, with a focus on the RI.INTRODUCTIONNew Jersey Turnpike Interchange 14A is located within the cities of Bayonne and Jersey City, in Hudson County, New Jersey. The New Jersey Turnpike Authority (NJTA) identified Interchange 14A as an area of mass congestion in need of redevelopment to improve the increasing demand of traffic and roadway safety. The New Jersey Turnpike Interchange 14A project included the construction of twelve (12) new roadways, in addition to the construction of four new bridges. The limits of construction are shown in Fig. 1.The fill height required to construct the roadway embankments varied from 2 to 34 ft. The proposed embankment side slopes varied from 6H: 1V to 2H: 1V. Additionally, mechanically-stabilized-earth (MSE) walls were utilized to retain the embankment fill along some segments of the roadways. As shown in Table 1, the proposed roadways were divided into six zones, based on location, subsurface condition, and embankment height."

Jan 1, 2017

By Frederic A. Verheyde

The CPT pile design method of the ‘Laboratoire des Ponts et Chaussées’ (LPC) uses the cone resistance (qc) for the design of axially loaded piles. It was originally proposed in 1982 and was revised in 1993 and 2012. It has been widely used in France for several decades and is included in the current French pile design code. The objective of this paper is to summarise the two first versions (1982 and 1993) of the method and to detail the most recent one as described in the current French pile design code (AFNOR 2012).

Nov 1, 2022

By Gerald Verbeek, Erick Baziw

"Downhole Seismic Testing (DST) is an important geotechnical testing technique for site characterization as it provides low strain (<10-5) in-situ interval compression (Vp) and shear (Vs) wave velocity estimates. These velocities are determined by obtaining relative arrival times of source waves as they travel through the stratigraphy and are recorded by one or more vertically offset seismic sensors. A challenging aspect of this process is to characterize the seismic data sets to determine the analysis method that will result in the most accurate interval velocity values. This paper introduces an assessment technique which utilizes linearity estimates (i.e., hodograms fitting straight lines) from the polarization analysis in conjunction with crosscorrelation coefficient calculations of the full waveforms as well as the deviation of the source wave frequency spectrum from a desirable bell-shaped curve. The paper will provide an overview of the technique and include some examples of actual data sets where the technique was applied to analyze those data sets.1. INTRODUCTIONIn general terms, Downhole Seismic Testing (DST) such as Seismic Cone Penetration Testing (SCPT) is a geotechnical technique for measuring in-situ shear and compression wave velocities (VS and VP respectively). The main goal in DST is to obtain arrival times as the source wave travels through the soil profile of interest, and from these arrival times the velocities are then calculated. Figure 1 shows a schematic of the typical DST configuration: a seismic source is used to generate a seismic wave train at the ground surface. One or more downhole seismic receivers are used to record the seismic wave train at predefined depth increments. The downhole receiver(s) may be positioned at selected test depths in a borehole or advanced as part of an instrumentation package as in the case of SCPT. When triggered by the seismic source a data recording system records the response of the downhole receiver(s)."

Jan 1, 2017

By Andrew McNamara, Stuart Norman, Matthew Dearing, Michael Pelken, Asha Panchal

The deep foundations industry has largely remained unchanged since in the advent of CFA piling in the 1960s. Piles have consequently been designed and constructed following the traditional codes and standards without much regard for optimising in-life efficiency or end-of-life reuse. After existing developments have been demolished there is little motivation to reuse existing piled foundations as their load bearing capacity and structural integrity cannot be verified. Therefore piling contractors are increasingly spending more resources on coring through existing piles, only to be replaced with larger diameter or deeper piles. The hollow element of the HIPER® Pile provides access to the entire length of the pile to permit inspections and a shaft in which the pile can be extended if needed. This paper presents and compares the embodied carbon savings, both during construction and through foundation reuse, from a HIPER® Pile scheme compared with the traditional solid pile scheme. A discussion on the benefits of this technology and its implications on warranties and approvals is also presented to motivate the foundations industry to embrace whole lifecycle assessments and support the journey to net-zero carbon.

May 1, 2022

By Leykam Chris J., Jacobs Scott. A.

"Construction of the New NY Bridge over the Hudson River 25 miles north of New York City is one of the largest civil infrastructure projects presently underway in the United States (formerly Tappan Zee Hudson River Crossing). The $3.14 billion Design-Build contract is also the largest ever awarded by the state of New York using an Alternative Project Delivery method, and the first major public project to use Design-Build. The new 3.1 mile long bridge will replace the existing Governor Malcolm Wilson Tappan Zee Bridge with a modern twin crossing featuring: Iconic side by side cable stay main spans; significant deck widths accommodating eight lanes of regular traffic, wide shoulders, and a shared use pedestrian and bike path; foundation with excess capacity to fully support a future rail bridge; more than 1,000 large diameter pipe piles driven in deep glacial deposits; drilled shafts installed through steep blast-rock slopes on the east shore landings. Geotechnical challenges included varied bedrock and glacial till surfaces with steep slopes and depths in excess of 750 ft.The purpose of this paper is to highlight major features of the New NY Bridge project with specific focus on the design and construction of the foundations supporting the approach and main span structures from abutment to abutment, provide background on alternative project delivery in NY, as well as provide an overview of the design-build process as it was applied to foundation delivery.The 3.1 mile Governor Malcolm Wilson Tappan Zee Bridge was constructed across the Hudson River connecting Nyack and Tarrytown (Rockland and Westchester Counties). Construction started in March 1952 and was completed in 1955 for a cost of $81 million. The seven lane crossing first opened to traffic on December 15, 1955 and coincided with the opening of a 28 mile segment of highway I-87 / I-287 between Suffern NY and Yonkers NY. The bridge is part of the extensive 574 mile New York State Thruway road system owned and operated by the New York State Thruway Authority (NYSTA)."

Jan 1, 2016

By Parameswaran V. S, Anshuman Singh

This is a case study on ground improvement using Stone columns at Kokrajhar in Assam which comes under seismic Zone V as per IS: 1893. The strata at site comprised of mostly fine sands with low SPTN values, fine content less than 10% and ground water table (GWT) at shallow depth. As ground water table subjected to seasonal variation, water table is considered at ground level for designing purpose. The geotechnical profile of the boreholes was analysed on the guidelines of IS 1893 (Part 1) -2016 and it was observed that the liquefaction potential of the soil layers is prominent and ground improvement is inevitable up to a depth of 9.5 m below existing ground level. In order to mitigate the liquefaction of soil layer, Stone columns were proposed. The in-situ soil is densified using wet top feed vibroreplacement method with an area replacement ratio of 16%, so that the relative density of the soil can be enhanced to prevent liquefaction risk. Correlation between relative density, fines content and increment of SPT N –value given by Tokimatsu and Yoshimi (1983) was used for designing purpose. Field tests such as SPTs were carried out at site to validate the extent of SPT (N) improvement. Detail comparison of pre and post density, SPT N values and CRR values were discussed in this paper.

Nov 1, 2022

By Ira Brotman

The Virginia Port Authority and the U.S. Army Corps of Engineers are partnering to construct the Craney Island Eastward Expansion (CIEE) to meet the dual purpose of extending the life of Craney Island as a dredged material management area and providing land for a state-of-the-art marine terminal. The over 500-acre (200-hectare) expansion provides additional upland dredged material capacity for the Hampton Roads Harbor by constructing perimeter dikes, that once filled, will provide land for the development of a container terminal. In the winter of 2010/2011 the first stage of sand fill was placed, followed by the installation of approximately 12 million linear feet (MLF) (3.6 million linear meters, MLM) of marine PVDs. With over 36 MLF (10.9 MLM) of PVD required to complete dike construction the project will be one of the largest PVD installation project in the U.S. his paper details the challenges associated with the construction of the cross dikes, in particular the design, testing, installation and monitoring of prefabricated vertical drains (PVDs) installed overwater to depths of over 130 feet (40 meters) for foundation improvement in the insitu very soft Norfolk Clay. With expected settlements of 20?30 ft (7-10 m) and 30 percent average strains, the discharge capacity of the PVDs was of particular concern. Laboratory data is presented showing the magnitudes and variability of discharge capacity under different confining pressures in both a straight and buckled condition. The method of installation and monitoring of the marine PVDs in open water included developing a specialized barge and sophisticated positioning and data collection system to verify installation location, depth of penetration and track quantities. An observational method, including material testing, detailed surveys, periodic in-situ testing, and instrumentation, was utilized by the project team to assess the project?s progress and allow for validation of consolidation and strength gain rates and magnitudes.

By Mohamed Mekkawy, William W. Wheaton, Ira Brotman

"The Virginia Port Authority and the U.S. Army Corps of Engineers are partnering to construct the Craney Island Eastward Expansion (CIEE) to meet the dual purpose of extending the life of Craney Island as a dredged material management area and providing land for a state-of-the-art marine terminal. The over 500-acre (200-hectare) expansion provides additional upland dredged material capacity for the Hampton Roads Harbor by constructing perimeter dikes, that once filled, will provide land for the development of a container terminal. In the winter of 2010/2011 the first stage of sand fill was placed, followed by the installation of approximately 12 million linear feet (MLF) (3.6 million linear meters, MLM) of marine PVDs. With over 36 MLF (10.9 MLM) of PVD required to complete dike construction the project will be one of the largest PVD installation project in the U.S.This paper details the challenges associated with the construction of the cross dikes, in particular the design, testing, installation and monitoring of prefabricated vertical drains (PVDs) installed overwater to depths of over 130 feet (40 meters) for foundation improvement in the insitu very soft Norfolk Clay. With expected settlements of 20–30 ft (7-10 m) and 30 percent average strains, the discharge capacity of the PVDs was of particular concern. Laboratory data is presented showing the magnitudes and variability of discharge capacity under different confining pressures in both a straight and buckled condition.The method of installation and monitoring of the marine PVDs in open water included developing a specialized barge and sophisticated positioning and data collection system to verify installation location, depth of penetration and track quantities. An observational method, including material testing, detailed surveys, periodic in-situ testing, and instrumentation, was utilized by the project team to assess the project’s progress and allow for validation of consolidation and strength gain rates and magnitudes."

Jan 1, 2017

By Babak Mamaqani, Pirooz Barar

Regional Connector Transit Corridor (RCC) is part of the Los Angeles metro expansion project under construction which adds three new stations into the system. PB&A was responsible for the design of the support of excavation (SOE) systems for two stations, 2nd/Broadway and 2nd/Hope, in RCC. In this paper, challenges and lesson learned from SOE design of 2nd/Broadway station with a main focus on underpinning design are discussed. 2nd/Broadway station required to cut and cover excavation of 500 ft long by almost 100 ft deep, underneath 2nd Street. SOE systems consisting of drilled soldier beams with tiebacks and/or struts. The main challenge in 2nd/Broadway station was to underpin the LA Times building which was partially protruded into the station. A chellenging underpinning system consisted of concrete panels and ground anchors was designed to support the building surcharge and prevent settlement. The underpinning system was designed based on METRO design criteria and the deflection was evaluated by Finite Element Analysis (FEA) program, PLAXIS 2D. A maximum deflection of 0.4 inches was calculated to occur at the top of the underpinning system. Data from settlement and tilt sensors showed minimal movements which aligned with PLAXIS outputs. PROJECT DESCRIPTION The Regional Connector Transit Corridor (RCC) is Los Angeles Metro’s ambitious Light Rail Project. It runs under the City’s main thoroughfares, Flower and 2nd Streets, and when complete will alleviate traffic and parking congestion in downtown Los Angeles. The Regional Connector will connect thousands of residents living in the bedroom communities of the Inland Empire and Long Beach to their jobs Downtown. The rail line will serve 1.9 miles, using the $1.756 Billion budget to construct the underground rail line, including 3 new stations, at 2nd & Hope Street, 2nd & Broadway, and 1st St. & Central Ave (Fig. 1).

Jan 1, 2019

By Seth K. Martin, Tony Nichlany, Alan R. Poeppel, Konstantinos Syngros

"This paper presents a case study on bored pile construction in challenging karst conditions below a supertall building in Kuala Lumpur. Innovative design and construction techniques helped keep the project moving through very difficult and unpredictable geological and drilling conditions. The development encompasses about 12,400 square meters and includes a 77-story tower, a 59-story tower, a five-story podium, and four contiguous basement levels. The site is underlain by a residual soil derived from a siltstone/claystone (the Kenny Hill formation), then limestone bedrock. Subsurface conditions are relatively uniform within the Kenny Hill and highly variable at the limestone surface. Extreme cases included 40-meter-tall underground caverns, 40-meter-tall pinnacles, and a 50-meter-tall underground rock ledge. Local piling practice in Kuala Lumpur involves deriving pile capacity entirely in the Kenny Hill formation to avoid the unpredictable limestone surface. However, the massive tower foundation loads and relatively shallow bedrock required the piles to be socketed in the limestone. The 77-story tower will be supported by 2.0- and 2.2-meter-diameter bored piles 50 to 100+ meters long, socketed in limestone, with working loads between 40 and 70 Meganewtons. Two Osterberg-cell load tests were used to develop a site-specific rock socket skin friction correlation with RQD. Exploratory rock probes were drilled at each pile location to design the rock socket length based on the rock quality and sloping rock conditions. The rock mass was pressure-grouted during each rock probe to improve the rock quality and fill voids in the rock.INTRODUCTIONThe Kuala Lumpur City Centre, home of the Petronas Towers and the world’s deepest foundations, will be the future home of a new supertall tower. The 77-story tower will be supported by a piled-raft foundation that relies on piles terminating in the highly erratic, karstic Kuala Lumpur limestone formation. The high building loads coupled with relatively shallow limestone across the majority of the tower footprint forced the piles to extend into the limestone."

Jan 1, 2016