Search Documents

By A. R. Dover

The Richmond San Rafael Bridge (Figure 1) is a 4.3 mile long major toll bridge span across northern San Francisco Bay. Tutor-Saliba/Koch/Tidewater (TSKT) conducted a comprehensive seismic retrofit, which was at the time Caltrans? largest-ever construction contract at $484 million. The robust foundation retrofit design of 11 bridge piers included the installation of 26 new, large diameter (126 to 162 inch OD, wall thickness 1.5 to 2.25 inches) CIDH and CISS piles, with steel pipe piles installed to tip elevations of Elev. ?140 to -220 ft, in water depths up to 70 feet. The open-ended steel pipe piles had initial sections ranging from 71 to 172 feet long, with full lengths that extended to the bay bottom and then through 100 to 130 feet of marine sediments to top of bedrock. The marine soils of most interest consisted mainly of soft to firm Young Bay Mud (YBM), a silty, moderately-sensitive clay common to SF Bay. A key constructability issue was the prediction of pipe piles ?running? under self weight (198 to 625 kips in air) and pile driving hammer weight (IHC S-500 with total assembly weight of 322 kips). The term "pile running" is used to describe the penetration of the pile into the soil due to the self-weight of the pile only. This issue was critical because 1) there was limited head room under the bridge deck, and 2) if piles run too deep, the pile splicing on several piles would be problematic (the lowest desirable pile top elevation after running was +10 ft). While running measurements are sometimes made during marine/nearshore construction, there is little published data on predicted vs. actual running. This paper discusses the running prediction under self weight for 26 piles, and the methodology used in developing the predictions, which ranged from 15 to 94 ft of penetration below mudline. Pile running was recorded and compared with predicted values. The prediction methodology was quite good, and no significant constructability problems were encountered. The authors ?tweaked? the model to provide a slightly improved prediction method. The paper presents the model, predictions, observations, and discusses important lessons learned.

Jan 1, 2006

By David A. Staab

Numerical modeling was used to investigate the feasibility of using two geophysical imaging techniques, cross-borehole ground penetrating radar (XBGPR) tomography and electrical resistivity (ER) tomography, for detecting and characterizing defects in deep-mixed soil columns. XBGPR modeling was accomplished with a three-dimensional numerical forward modeling code and a two-dimensional inversion routine. Spatial variations in apparent dielectric constant (Ka) and attenuation (a) were mapped. Electrical resistivity modeling was accomplished with a three-dimensional numerical forward modeling code and a three-dimensional inversion routine. Spatial changes in electrical resistivity were then mapped. Three different types of defects were simulated, in addition to a defect-free column. The computer simulations suggest that XBGPR tomography and ER tomography might be useful, non-destructive methods for detecting and estimating the extent of defects in deep-mixed soil columns. The results show that small, isolated defects might be difficult to detect, but defects approximately equal to or larger than the sampling interval (for XBGPR) or vertical electrode spacing (for ERT) should be detectable.

Jan 1, 2004

By Wolfgang G. Brunner

The center of Berlin is currently a huge jobsite, where international architects, designers, consultants, construction and ground engineers as well as investors take on the challenge of the biggest and probably most complicated projects in terms of soil conditions in Europe. The Berlin sand is generally suitable for foundation measures, but can be very tricky in deep excavation pits below the high ground water level. The reason for this is its uniform grading, medium dense stratification and lack of cohesion. The requirements for these deep pits are: - measurements in the range of up to 120 000 m2 per pit - depths up to 19 m below ground water level - lack of dense horizontal geological layers - no permission for lowering ground water levels - toughest ever European competition in construction. Sheet pile walls, sheet piles set into cut - off walls, secant pile walls, diaphragm walls, all with tie backs under high water pressure, are used as retaining sytems. The pits are closed at the bottom against water either by under water concrete, deep lying grouted cut - offs or high lying jet - grouted cut - off slabs. The huge dimensions of these excavation pits are a new challenge for ground engineers, and new technology had to solve the upcoming problems and resulted in new experience.

Jan 1, 1999

By Lin Daoyi

In this paper, we have adopted the high pressure jet-grouting curtains to seal the sea-water, and to consolidate the wall of the well for deep foundation diteh, make a pladge of building and construction of deep foundation was primarily on progress without water. This paper, we have been given a test for pumping water under mainly the circumtances of sealing condition and to report in advance the capacity of seawater seeping into the gam curtains in the process of building and construction of deep foundation.

Jan 1, 1991

By Darrell L. Beddard

The Loma Prieta earthquake occurred on October 17, 1989 at 5:04 PM, Pacific Daylight Time. It measured 7.1 in magnitude and was felt from Los Angeles north to the Oregon state line and east to western Nevada. The epicenter of the earthquake was located along the San Andreas Fault, in the Southern Santa Cruz Mountains just north of the City of Watsonville, California. It was the largest earthquake to occur in the San Francisco Bay area since the 1906 earthquake. A total of 87 aftershocks of Magnitude 3.0 or larger were recorded within 21 days after the seismic event. As a result of this earthquake thirteen State-owned and five locally-owned bridges were closed to traffic. Three of the most publicized State-owned structures closed to traffic were Struve Slough Bridge, San Francisco-Oakland Bay Bridge and Cypress Street Viaduct. Struve Slough Bridge was twin slab bridges that collapsed and were rebuilt and open to traffic three months after the earthquake. San Francisco-Oakland Bay Bridge experienced collapse of upper and lower spans at Pier 9 and was reopened to traffic one month after the earthquake. The Cypress Street Viaduct experienced collapse of 48 bents that resulted in the upper roadway falling onto the lower roadway.

Jan 1, 1995

By Edwin W. Meyer

The augered cast-in-place piling technique was used to install deep foundations 20 feet into weathered sandstone. The project involved the upgrading of the Air Quality Control System (AQCS) for a 560 megawatt coal fired power plant located in Stillwater, Minnesota. The site subsurface consisted of 20 feet of overburden overlying weak sandstone. The overburden consisted of sands and gravels with cobbles and boulders, and variable thicknesses of peat. Ground-water at the site was approximately 8 feet deep. Two foot diameter piers were selected to facilitate installation through the cobbles and boulders in the over-burden and to penetrate the sandstone 22 feet. During installation of the first pier, the weak sandstone broke down to sand-sized material that could not be cleaned from the pier hole without the use of slurry to hold the material in suspension. However, the use of slurry would significantly impact both schedule and cost. Since the sandstone could be easily drilled with the pier equipment, it was believed that 2 foot diameter deep foundations could be installed as designed using augered cast-in-place piling techniques. A brief test drilling pro-gram was conducted to evaluate the viability of 2 foot diameter continuous flight augers penetrating 22 feet into the weak sandstone. The test drilling indicated that augered cast-in-place installation techniques should be successful. Following a short delay to mobilize the additional required equipment, construction commenced. Installation of the 2 foot diameter augered cast-in-place piling to a depth of 22 feet into the weak sandstone was successfully performed.

Jan 1, 2006

By Wolfgang G. Brunner

A 3800 m long temporary water-retaining dike has been constructed under extreme conditions in the harsh northern climate to enable two of the kimberiite pipes at the Diavik Diamond Project reserve to be mined using open pits. The Diavik Diamond Project is located on East Island at Lac de Gras in Canada's Northwest Territories, approximately 200 kilometres south of the Arctic Circle. The dike which has been constructed in up to 25 m deep water from crushed granite quarried from the site projects into Lac de Gras encircles the first two of the kimberiite pipes to be mined. An 800 mm wide diaphragm cut­off wall constructed of bentonite, cement and crushed rock, totalling 33,000 m2, and a two-phase jet grouted curtain wail at its base, totalling 8,400 m2, have been installed through the dike and underlying till foundation into bedrock. The cut-off is designed to minimise water seepage from Lac de Gras through the dike. In order to ensure that the dike had adequate internal stability and diaphragm wall construction could proceed safely, the crushed rock fill material dumped into the lake was first compacted by TR 75 deep vibrators. In 2000, Bauer Maschinen GmbH of Schrobenhausen, Germany were awarded the contract for the supply of all specialist foundation equipment required on site and for providing technical support to the Canadian main contractor Lac-de-Gras-Construction throughout the construction of the cut-off walls during 2001 and 2002. Installation of the cut-off walls was completed in July 2002, three weeks ahead of schedule, and dewatering of the inner dike areas commenced just 5 days later and has continued throughout August and September. After completion of extensive testing of the diamond recovery plant, the mine is scheduled to go into full open pit production in February 2003.

Jan 1, 2003

By Robert W. Schaut

The use of micropiles is increasing for new construction and to retrofit distressed foundations in expansive soils. Typical micropiles in expansive soils have a lower section where the micropile grout is embedded in direct contact with the soil, and an upper section that is cased with rigid PVC pipe or other material to reduce the friction between the micropile and the surrounding expansive soil. In the upper cased section, the micropile grout is in direct contact with the inside of the casing. During construction, grout can flow upward into the annular space between the soil and the outside of the casing as the grout is tremied into the micropile. Thus, various interfaces may exist in a typical micropile, including soil-to-grout, grout-to-PVC, and soil-to-PVC. As the surrounding soil heaves, shear stresses are mobilized along the interfaces. The frictional characteristics of the interfaces are design variables that must be evaluated. For this study, an experimental program was conducted to evaluate the shear strength of the three interfaces listed above. Conventional direct shear testing was performed at a commercial testing laboratory. In addition, specialized testing was performed at Colorado State University (CSU). For the CSU testing, an interface testing protocol was designed using a modified triaxial cell to allow evaluation of the interface characteristics between rigid PVC and cylindrical specimens of grout or clay soil. It is shown that the shear strength of the soil-to-PVC and grout-to-PVC interfaces are similar, both of which are significantly lower than the shear strength of the soil-to-grout interface. This indicates that the use of a PVC casing in the upper portion of a micropile has a positive effect in reducing friction and the shear stresses resulting from expansive soil.

Jan 1, 2011

By Jared M. Green

This paper presents the wall stabilization design and implementation for a 541 linear ft masonry and concrete gravity-type retaining wall flanking the west perimeter of a 7.37 acre parcel in Bronx, New York. This paper will discuss the results of static and dynamic stability analyses performed for the pre- and post excavation phases for the proposed 300 ft wide open-cut of up to 14 ft of contaminated soil below the toe of the retaining wall. The wall stabilization consisted of over 74 inclined drilled and grouted anchor dowels, and 55 tiebacks drilled and grouted to the underlying mica schist bedrock. Three over-lapping rows of jet grout columns were chosen as the foundation solution for the existing retaining wall. This paper focuses on the design, construction and performance of the jet grout curtain wall. The jet grout wall served three purposes: 1) underpinning and excavation support for the removal of contaminated site soils, 2) permanent hydraulic barrier, and 3) resistance against a deep seated failure within the thick clay layer present at the site. The originally designed jet grout wall had unexpected negative effects to the existing retaining wall. The jet grouting program was modified while the Observational Method (Peck 1969) was employed to keep wall movements to a minimum. This paper discusses the diagnostic methods used to determine the cause of retaining wall movement; the implementation of a remedial ground improvement program; the modification to the jet grout installation procedure; and the ultimate performance of the jet grout wall.

Jan 1, 2011

By David Siu

Many problems were encountered with the mechanical wedge-type splices used for the 15-inch square precast prestressed concrete piles installed at an industrial plant site. Many of the wedges were breaking during installation of the splices and after pile driving resumed following splicing. Dynamic monitoring of the piles and uplift loading tests confirmed that the problems were associated with cracked or damaged wedges. More ductile, annealed wedges were subsequently used, and, while not completely satisfactory, they were found to perform better than the original more brittle wedges. Introduction Long precast prestressed concrete piles were installed to support heavy, settlement-sensitive structures at an industrial plant in Port Alberni, British Columbia, Canada. The piles were driven through soft compressible silts and clays to toe bearing in a dense sand and gravel deposit or on bedrock. Each pile consisted of two or three segments joined with mechanical wedge-type splices trademarked DYN-A-SPLICE. Shortly after construction began, problems arose during pile installation, and these problems were, later, identified to be related to the wedges, or clamps, used to connect the splice plates.

Jan 1, 1991

By Alec C. Bloem

A 55' deep excavation encompassing almost a city block in London, Ontario required a lateral earth retention system to provide both temporary excavation support and a permanent groundwater cut-off wall for a proposed office complex. The system selected was an interlocking Drilled Shaft wall with 3-4 levels of tiebacks. The specifications required the system to be designed for movements or settlements around the excavation of ¼" max. Design to be by the Contractor with design parameters and a comprehensive soils report provided. An extensive system of instrumentation in the form of inclinometers and survey targets were used to monitor vertical and horizontal movements of the shoring system and adjacent properties. Introduction The project, One London Place, is a two phase office tower development in downtown London, Ontario. Phase one consists of a 24 storey office tower on the northwest part of the site, with five levels of below ground parking over the entire site "Figure 1". A second office tower will be constructed at a future date.

Jan 1, 1991

By Giovanni A. Bonita

The United States Capitol Visitor Center (USCVC) is one of the largest underground structures ever constructed in the Washington, DC, metropolitan area. The 600,000 ft2 (55,750 m2) structure is entirely underground and immediately adjacent to the shallow foundations of the existing U.S. Capitol building. Interior building columns for the USCVC were supported on 186 drilled shafts that varied in diameter from 4 to 9 ft (1.2 to 2.9 m) and in length from 15 to 45 ft (4.6 to 13.7 m). The vast majority of the building utilities were located beneath the basement floor slab. It was decided at the onset of the project to proceed with construction prior to completion of the design drawings, and coordination between the underslab utilities and the drilled shafts had not yet been finalized at the onset of drilled shaft installation. Given depth and location restrictions of the outlets, relocation of the bulk of the utilities was not possible. Almost half of the drilled shafts were affected, leaving redesign as the most feasible remedial solution. The redesign involved adjustments to the shaft length, diameter, and bell. It took place on a case-by-case basis, sometimes only minutes before installation began. Coordination between the field and design team was excellent, and delay associated with the redesign efforts was minimal. In addition, the detailed, high-quality field records kept by both the contractor and field engineers allowed for accurate and fair estimations of the added drilled footage and concrete volumes placed. The additional service fee, which was minimal, was settled quick and fair.

Jan 1, 2006

By Francis D. Leathers

Four friction pile load test programs, including 23 tension tests and 9 compression tests, have been performed as part of the Central Artery/Tunnel Project in Boston, Massachusetts. The tests, performed on both precast, prestressed concrete (PPC) piles and steel piles, yielded the following adhesion values: [Soil Type Clay Clay Glacial Till Interbedded Sand and Clay Interbedded Sand and Clay Pile Type PPC Steel Steel Steel PPC Adhesion (psf) 610 to 1,200 230 to 900 220 to 550 680 1,280 ] The adhesion appears to be affected by differences in pile material type, with PPC piles having higher adhesion than steel piles. However, part of the apparent difference for the clay may be due to differences in time between driving and testing. The significant range of test data means that the need for site specific testing to determine or verify design values of adhesion should be considered during design. Creep rates at loads near failure ranged from about 0.02 to 0.18 inches per log cycle of time, with most values in the range of about 0.04 to 0.08 inches per log cycle of time.

Jan 1, 1994

By Charles F. Seemann

It is with considerable trepidation that I set out to defend "litigation" to Design Professionals (DPs), as a better method of resolving disputes than arbitration, in the light of my personal feeling that an increasing amount of America's productive process is being squandered in litigation. Newer methods of dispute resolution, particularly arbitration, are fashionable, and opponents of these schemes risk being viewed as cynical or self-serving. My quandary is heightened since for some smaller disputes, arbitration seems clearly the better choice. I must concede, for example, that when the cost of dispute resolution--i.e., the cost of the process (such as arbitrators fees, attorneys fees, etc.), plus the cost impact of the non-productivity of involved employees--approximates the amount of the dispute, controlling that cost may be as important as a correct resolution. This principle is particularly true for small disputes arising during the progress of a project; it is probably more cost-effective for all parties to resolve their disputes quickly than permitting the dispute to drag out.

Jan 1, 1988

By Mohammad Nasim

Vertical expansion of existing structures frequently requires foundation retrofitting to enhance the capacity of existing foundations for supporting additional loads. Owing to their small diameter, a variety of suitable drilling methods available for installation, and smaller installation equipment capable of operating under limited headroom conditions, micropiles are often preferred for foundation retrofitting. This paper presents a case history demonstrating application of micropiles to underpin the existing foundation of the Washington D.C. Children?s National Medical Center (CNMC) for its future expansion. Located at 111 Michigan Avenue in northwest Washington, DC, portions of the hospital currently extend five stories above grade and three levels below-grade as parking garages. The hospital intends to expand the surgical wing up to the current build out (five stories) above the remaining portion of the existing parking garage. The original foundations consist of 80-ton Raymond Step-Tapered piles. New loading on the foundations required each Raymond pile to be capable of supporting 150 tons. Results from quick load tests on existing piles indicated that two entire column lines (Column Line A and B) would experience loads beyond their capacity, requiring enhancement of the existing foundation at these locations. The design and construction of the foundation upgrading work was particularly challenging due to various project constraints related to a high groundwater table, micropile installation under limited head room, and ensuring that the parking garage remained fully operational for the entire duration of construction. The paper presents the challenges faced during testing of existing foundations amid a high groundwater table, design developments of underpinning options to support the additional column loads, difficulties and challenges encountered during installation of the micropiles and construction of the micropile pilecaps, and value engineering options developed during various phases of the project. Understanding that micropiles are often a preferred option for foundation retrofitting, the case history is expected to provide a baseline design approach and innovative solutions to typical challenges faced during construction, thereby reducing potential cost overruns during design development and construction of similar future projects.

Jan 1, 2008

By Carole L. B. Mitchell

The South 180th Street Grade Separation underpass in Tukwila and Renton, Washington, USA, permits vehicular traffic to pass beneath Burlington Northern Santa Fe and Union Pacific railroad tracks. The railroad tracks were temporarily relocated onto a shoofly crossing while the permanent bridges were constructed. The maximum underpass depth is approximately 25 feet (7.6 meters [m]). The majority of the sidewalls are supported using alternating reinforced and unreinforced secant pile walls. Temporary and permanent struts brace the top of the excavation. Because the groundwater is about 15 feet (4.6 m) above the base of the excavation and the subsurface materials are loose to medium dense fill, alluvium, and soft flood plain organics, the base of the excavation was strengthened and sealed using wet cement deep soil mixing (CDSM) methods. During construction, CDSM-treated ground temporarily acted as part of the railroad shoofly shoring while the remainder of the underpass was excavated on either side of active railroad tracks. The combination of secant pile sidewalls and CDSM bottom seal allowed for easy excavation, even during wet conditions. Using a 35-foot-thick (maximum) (10.7-m) CDSM layer both to act as a bottom seal and to resist uplift pressures is a unique, dual-purpose application of CDSM technology in the United States.

Jan 1, 2004

By d&apos, E. Appolonia

A construction project is successful when all parties contributing to it are winners. It is not a success when there are winners and losers. Con­tractors, engineers, suppliers and equipment developers, and especially owners, each can contribute and benefit from a revaluation of attitudes and contacts from planning to final payment. The Deep Foundations Institute was initiated with this as its major purpose. The help of educators is essential to promote this with the next generation. The Association of Soils and Foundations Engineers has developed guides for "Mediation Arbi­tration of Construction Contracts."

Jan 1, 1985

By Mandy Korff

Walls consisting of CFA-piles are often used for vertical cut offs for building pits. Several methods of installation and geometry may be used and sizes, depths and strengths of walls necessary vary widely. Based on experience with secant CFA-pile walls in The Netherlands, requirements for this type of wall can be set with a risk management view to it. This paper describes those requirements, based on specific local conditions.

Jan 1, 2006

By Larry Rayburn

In the spring of 1999, construction commenced on the new Steelers Football Stadium in downtown Pittsburgh, Pennsylvania. Richard Goettle, Inc. (RGI) was the successful bidder to install the specified augercast piles for the foundation package. Description - Pittsburgh Steelers Stadium The new stadium will house the Pittsburgh Steelers Professional Football Team. It is widely believed that if a team is provided with a modern playing facility, that a winning season will ensue (Not always the case). The new stadium location is on the north side of Pittsburgh on the Ohio River, and just downstream of the confluence of the Monongahela and Allegheny Rivers. The site is west of existing Three Rivers Stadium. The Three Rivers Stadium was built during the late sixties and housed both the Pirates Baseball and Steelers Football Teams. The Public Auditorium Authority elected to replace this outdated stadium with two new stadiums, one for each professional team. The landmark stadium was imploded in February of 2001.

Jan 1, 2001

By Stanley A. Schwartz

In the Piedmont, heavily loaded structures are generally supported by either drilled piers or one of several pile types. The choice of drilled piers or piles is typically one of comparative costs. The cost of a drilled pier foundation is usually the more difficult to predict because of the greater impact that variable conditions and construction monitoring have on cost. Poor specifications, related to the drilling equipment, procedures and bearing level, can also result in large cost extras. In the southern Piedmont, straight shafts are typically extended down to hard rock to achieve primary support in end-bearing: when bells are required, they are often constructed manually. In some eastern and northern Piedmont locations the thickness of the decompossed rock zone is significant and considerable skin friction can be mobilized. Typically piers are constructed in holes temporarily cased with steel liners. The bottom is cleaned of loose material and water, and then evaluated by a geotechnical engineer to confirm the design bearing pressure (and friction, where appropriate) or recommend alternative construction measures.

Jan 1, 1988