Search Documents

By Peter Bourke, Marc van Olst, Seppo Ronkainen, Natalie Brown

"Since the early days of flotation, process technicians have known that the speed at which the froth is recovered over the lip of the cell has a very direct and consistent influence on the grade and recovery of the circuit. No plant would deny that, even to this day, one of the most important aspects of a process technician’s job is ensuring that the froth is moving at a desired and controlled speed over the lip. Unfortunately, process technicians cannot watch the froth throughout the entire shift, as there are always a lot of other tasks to do.A considerable amount of work has thus been done to develop a “system” that automatically measures the speed of the froth. This measurement would then be used in simple controllers to emulate the steps taken by the process technician in correcting deviations of the froth speed from its desired level. Many of the earlier attempts to measure speed were ineffective, as they were unable to cope with turbulence on the froth surface. The FrothMasterTM instrument makes use of machine vision technologies to measure the speed of the froth over the lip of a cell at a very high sampling rate. This instrument produces an extremely reliable and accurate measurement of the froth speed (as well as other parameters such as bubble size and froth stability). As we will show, the effectiveness of the speed measurement in controlling the performance of the plant is a testimony to its reliability.Three FrothMasterTM units have recently been installed on the Cadia Hills Gold Mine in New South Wales (Australia). The objectives of this installation were:To control the mass-recovery of two Tank Cells in series on the same level where differences in the hydrostatic head between the two cells result in the cells pulling inconsistently with respect to each other.Control of the concentrate grade (%Copper) from the first rougher.Reduction in the frother consumption in the rougher circuit by monitoring the froth speed.A simple controller was designed to react to disturbances in the same way that human operators react. This was done after consultation with the metallurgists and the process technicians at Cadia. The controller had two functions:Stabilisation: The stabilising controller made use of three manipulated variables (level, frother addition rate and aeration rate) to control the froth speed to a setpoint.Optimisation: The optimising controller adjusted the froth speed setpoint based on deviations of the grade (measured in real-time with an OSA) from a setpoint. The plant metallurgist adjusted the grade setpoint based on information about the ore."

Jan 1, 2001

By P. Hickey

"The object of this paper is to describe how the Iron Ore Company of Canada develops its management personnel. It will elaborate on the practical application of Supervisory Training and Management Development.Why are Supervisory Training and Management Development important? The answer has been the subject of many textbooks. Dr. Ken Blanchard, author and consultant, addressed this issue concisely when he said that effective managers and organizations must do two things, ""get results and develop people"". lPeople development at IOC is best illustrated through its supervisory training and management development programs. For the past twenty-five years IOC has been recognized as an industry leader in the training field. Periodic studies have played their role in establishing and maintaining this distinction. For example, in 1974, the company decided to review and up-date all its training programs. At this time, it established its own Task Force on Training and this resulted in the development of many of our present programs. Today, Supervisory Training (i.e. for first and second level management) at the Carol Project in the Labrador City area consists of various programs including: New Foreman Induction, Foreman Entrance School, Basic Management Skills, Management II, and Effective Presentations."

Jan 1, 1983

By Patrick J. Williams, Peter J. Pollard

"Abstract - Enigmatic hydrothermal vein/breccia/replacement Cu-Au deposits with magnetite and/or hematite are well-represented in Australian 1850 Ma to 1500 Ma terrains and associated with different-aged synorogenic intrusions in the Tennant Creek Block (ca. 1850 Ma); the Gawler-Curnamona region (1640 Ma to 1590 Ma); and the Cloncurry district (Mount Isa Eastern Fold Belt, 1540 Ma to 1500 Ma with a possible earlier event at ca. 1600 Ma). No deposits are known to be coeval with various 1780 Ma to 1610 Ma anorogenic intrusions. Deposits are hosted by many different rock-types with varying metamorphic grade including granites and various supracrustal rocks. Depth of mineralization varied from many kilometers in semiductile crust (e.g., Cloncurry deposits) to very shallow (e.g., Olympic Dam). Ore deposition near Cloncurry occurred in brittle-ductile shear zones from geochemically variable and complex, CO2-rich, 300°C to 500°C, high salinity fluids with magmatic stable isotopic signatures. Recently published studies of a giant granitoid-hosted magnetite vein complex at the Lightning Creek prospect (>1000 Mt magnetite) suggest it is a product of internal differentiation and endogenous Fe and Cu-rich hydrous-carbonic fluid phase generation within a quartz monzodiorite-monzogranite intrusion. Coupled with other field relationships, this points to a possible genetic relationship with intermediate (55 to 65 wt% SiO2) members of an alkaline and partly shoshonitic granitoid supersuite which appears to have both mantle and crustal source components from ?Nd evidence. In constrast, main-phase mineralization at Olympic Dam in the Gawler Craton is distinguished by hematite-phyllosilicate alteration and chalcopyrite-bornite-chalcocite zoning, reflecting fluid mixing in a high level (<250°C) system with a probable large component of meteoric water. Early high-temperature parageneses and fluid inclusions imply that the extensive hematitic breccias overprinted an older magnetite system which may have had similarities with those at Lightning Creek and Ernest Henry in the Cloncurry district.Deposits of this family are inherently difficult to find and evaluate as even within a single district, there is no reliable relationship between the location of ore and any specific combination of geophysical characteristics. Diverse alteration assemblages, geochemistry and physical characteristics suggest the deposits reflect the interaction of multi-sourced fluids with different host rocks in a wide range of geological environments. Recent discoveries and research in the Cloncurry district have extended the range of deposit models available and aid the development of a rudimentary classification in which economic and exploration characteristics can be linked to variations in the mechanisms and environments of ore formation."

Jan 1, 2001

By C. Pelley, S. Kelebek, G. Kunzel, S. Gregersen, M. Pollanen

A series of small-scale tests was conducted to evaluate the effect of micro-fracture development, imposed by blasting, on the material properties of the rock as well as its resistance to crushing and grinding. The uniaxial compressive strength, tensile strength, Poisson’s ratio, Pwave, S-wave velocity, point load test index, crushing, and grinding work indices were evaluated for samples without any blasting load and for samples which had received a variety of blast loads ranging from a single impact with a lowstrength detonating cord to a combination of impacts at different times and significant impacts with powder factors close to those used in practical blasts. It was shown that the rock mechanics parameters change even at low impacts, suggesting easier crushing of the rock. Damage values appear to be affected by timing as stress wave superposition affects the damage process. Fragmentation is achieved at higher impact levels while work index modification of the fragments is also observed when high powder factors are used, suggesting improvements in grinding.

Jan 1, 2006

By Ken Norris

"Campbell Mine which has been in continuous operation since 1949 has undergone numerous operational changes in the past 3 years. This paper describes the process changes which have occurred at the Campbell Mill since 1991. The paper discusses the engineering, construction and startup of the effluent treatment circuit, the new oxide filtering and merrill-crowe precipitation circuit, and the changes to the pressure oxidation circuit. Particular attention is paid to startup problems and solutions to these problems. A review of the benefits and results of these process changes is also discussed. Future changes are also briefly reviewed with anticipated goals and expectations.IntroductionCampbell Mine is a gold mine 100% owned and operated by Placer Dome Canada. It is located in Balmertown, Ontario which is located 300 kilometres northeast of Winnipeg, Manitoba. The Campbell Mine has been in continuous operation since 1949, producing nearly 8,000,000 ounces. In 1993 Campbell Mine is budgeted to produce 289, 750 ounces of gold at a cash cost of $157 US/ounce. Daily mill tonnage is budgeted for 1,430 tons/day but has milled as high as 1,600 tons/day on a consistent basis. Recovery in 1993 is 93.4% and is budgeted to average 94.5% in 1994.In the 1992 edition of the proceedings of the Canadian Mineral Processors conference I described the changes that were made at Campbell starting in 1989. This paper continues where the 1992 paper ended and discusses the changes to the Campbell mill since that lime. The changes to Campbell since January 1992 have been numerous with capital expenditure in the mill exceeding $14.1 million. This paper describes three primary projects since that lime: the effluent treatment project ($5.5 million), the oxide leach/filtering and merrill-crowe project ($4.6 million) and the pretreatment project ($2.81 million). The focus of this paper is to highlight the justification of each project, the design and engineering, and some of the initial operational problems and solutions applied to those problems."

Jan 1, 1994

?? Intro ?? Mass blast principle ?? LaRonde evolution toward mass blast ?? Overview ?? Mining method ?? Longitudinal ?? LaRonde evolution (2002 to today) ?? Drill and blast design ?? Consumptions and statistics ?? Mucking strategies ?? Case study ?? Examples ?? Conclusion ?? As underground mines extends to greater depths, few questions must be asked: ?? How to: keep operations safe eep operation effective reduce the cost maintain and control the dilution ?? Geomechanic method and practices; significant advances have been observed in the field of: ?? ground support ?? mining sequencing ?? Drilling and blasting; research and development has been less extensive, probably due to the following characteristics: ?? Drill and blast are mainly production-oriented ?? Drilling and blasting are more oriented toward productivity ?? Technology relies heavily on suppliers ?? Highly stressed ground conditions ?? generally help the explosives to break the rock for fragmentation ?? intensify over-breaks or blast-induced

Feb 1, 2008

By H. Wyslouzil

"The Kelsey Centrifugal Jig is a gravity separation device which utilizes the principles of the conventional mineral jigs but with the additional feature of being able to vary the apparent gravitational field. This is accomplished by utilizing the specific induced movements of the conventional jig within a centrifuge.Pilot plant trials have been underway since July 1988 to evaluate the potential applicability of this technology to various process streams at Rio Kemptville Tin.The grade/recovery relationships for samples treated in the jig were consistently better than results obtained from tables. Recoveries of more than 90% were attained at concentrating factors ranging up to 20. When compared with electrostatic separators, the jig achieved equivalent metallurgical results in a two stage process, without the expensive requirement of filtration and drying. Recoveries exceeding 96% were achieved with final concentrate grades averaging higher than 60% tin.INTRODUCTIONMineral jigs have been used for hundreds of years. Many different types have been developed, and each one has numerous variations. In recent years, the idea of applying centrifugal forces to conventional jigs has been put to practical tests and today a number of units are in commercial production. In principle, by enhancing the apparent gravitational field, it should be possible to recover finer particles by overcoming viscosity and surface effects which tend to limit existing gravity devices. In addition, it may be possible to use gravity to separate minerals with much smaller specific gravity differences."

Jan 1, 1990

By C. A. Rowland Jr

"I. INTRODUCTIONFred C. Bond's ""Third Theory of Comminution"" (1) was published in 1952. The mathematical statement of the Third Theory is the well-known Bond Formula:where W - Kw H per short tonWl - Work IndexP - Product size in microns which 80% passesF .. Product size in microns which 80% passesWork Index, as defined by Fred Bond, "" ... is the comminution parameter which expresses the resistance of the material to crushing and grinding. Numerically, the Work Index is the KwHrs per short ton required to reduce the material from theoretically infinite feed size to 80% passing 100 microns."" (2)Work indices for grinding can be obtained tram Bond grindability tests and can be calculated from plant grinding mill operating data when power consumed per ton of ore ground, the feed size analysis and the product size analysis are known.Work indices obtained tram Bond grindability tests, having been obtained from standard and controlled laboratory procedures, are reproducible and for the sample tested are accurate. The degree of accuracy relative to plant mill operation depends upon how representative the sample is of the total mill feed.The results of the Bond closed circuit rod and ball mill grindability tests (3) are given in grams of product sized material produced per revolution of the test mill. In developing a method to evaluate plant operating data and results from his grindability test, Fred Bond developed the ""Third Theory of Comminution."" In the process formulae were developed for converting grams per revolutionobtained from grindability tests to work index.The standard feed sizes for the Bond grindability tests are:Rod Mill Test ore crushed to minus 1ll inchBall Mill Test ore crushed to minus 6 mesh (Tyler)The formulae for converting grams per revolution to work index incorporate the 80% passing sizes for the feed to and the product produced in the specific test. Therefore, accurate work indices can be obtained from Bond grindability tests when the feed size is finer than standard. To obtain accurate test results, the ratio of reduction should be greater than 6 to 1."

Jan 1, 1972

By C. O?Connor

With ever-increasing global demand for mineral resources, numerous mines are moving towards developing and mining deeper, more complex and lower grade ore bodies. In many cases, mass mining methods (e.g. block caving) are being considered to deal with deeper, lower grade deposits. The body of practical knowledge, however, related to the impacts mass mining methods have on the surface environment in terms of rock mass response, subsidence, etc., is limited, imposing both economic risks to the mine and safety risks to mine personnel. This paper presents the framework for and preliminary results from a large collaborative research initiative between Diavik Diamond Mines, Rio Tinto, the University of British Columbia (UBC) and Simon Fraser University (SFU). The project involves the integration of available subsidence, rock mass, mine operation and monitoring data, together with the advanced application of combined finite/discrete-element modelling codes capable of simulating fracture behaviour, cave propagation and surface subsidence above block cave mines. The main objective of this work is to develop advanced numerical modelling methods to characterize complex rock mass behaviour above block cave mines. The research will also include the study of rock deformation mechanisms associated with the transition from surface to underground mining and the potential interaction between simultaneous open-pit and underground mining operations.

May 1, 2007

By Jim Lauder, Russ Calow, Ken Maley, Michael Ounpuu, Stuart T. Caverly

"Stuart T. Caverly, Section Head XRF Laboratory, Jim Lauder, Systems Engineer, Russ Stuart T. Caverly, Section Head XRF Laboratory, Jim Lauder, Systems Engineer, Russ Concession Street, Lakefield, Ontario KOL 2HOAbstractOn-stream X-ray analyzers have become an integral part of modem milling operations. The calibration of these instruments is not difficult but must be performed carefully and with consideration for the principles of X-ray spectrometry. A discussion of successful calibration procedures as well as examples of several common mistakes is presented.IntroductionOn-stream X-ray analyzers (OSA) have become an integral part of modem mineral dressing plants. Advances in instrumentation and computer software make the analysis of process streams fast, accurate and precise. Proper instrument calibration that respects the fundamentals of X-ray spectrometry is essential if the data generated are to be reliable. Often the importance of this task is underestimated and delegated to a person with inadequate XRF training. Successful OSA calibration is the result of careful, systematic procedures.On-stream analysis is perhaps the most important tool that has been provided for the concentrator metallurgist. Combined with powerful, low cost PC's and distributed control systems, real-time elemental analysis affords today's metallurgist many opportunities to troubleshoot and optimize his process.Before OSA, operators had to be very experienced if they were to achieve good results. Even with hourly grab samples, most changes in control approach would still be based on visual cues from the circuit and gut instinct. Real-time analyses have changed that completely.The last two decades have seen a persistent drive to reduce production costs. Operations utilizing OSA have been the most successful in this endeavor. Direct benefits from the application of OSA are fairly obvious. Operators are able to make incremental changes in operational parameters (e.g. reagent addition, pH, cell level), and immediately monitor the effects. Variations in the characteristics of the mill feed can be identified and addressed immediately. More progressive operations have linked analyses to control loops to adjust process setpoints ( e.g. reagent additions), and to change them automatically according to formulas based on previous experience."

Jan 1, 1996

By K. G. Thorne, M. J. McLeod, D. Hoy

"Throughout the Paleozoic, a variety of gold depositional environments were created in the New Brunswick segment of the northern Appalachians because of the complexity of arc and continental plate collisions and subsequent erosion of the orogen. In southwestern New Brunswick, recent exploration and research has focused on deposits and occurrences that can be broadly classified as intrusion-related, generated by late- to post-orogenic felsic to intermediate plutonic rocks emplaced during the Early to Middle Devonian. This work has led to the establishment of models for gold mineralization and guidelines for exploration in this area, which might also be applicable elsewhere in the southern part of the province and, perhaps, throughout the northern Appalachians. The deposits in the vicinity of Clarence Stream in southwestern New Brunswick exemplify this deposit type, and highlight the emergence of a possible major gold district in the region. Durant le Paléozoïque, une grande variété d’environnements aurifères ont été créés dans le segment néo-brunswickois des Appalaches du nord en raison de la complexité des collisions entre arcs et plaques continentales ainsi que durant l’érosion subséquente de l’orogène. Dans le sud-ouest du Nouveau Brunswick, les travaux d’exploration et de recherche récents se sont tournés vers les gisements et les indices appartenant à la classe des gîtes associés aux intrusions, générés par des roches plutoniques felsiques à intermédiaires tardi- à post-orogéniques mises en place au Dévonien précoce à moyen. Ces travaux ont permis d’établir des modèles de mise en place pour la minéralisation aurifère ainsi que des guides d’exploration pour ce secteur, lesquels pourraient aussi être appliqués ailleurs dans le sud de la province et, possiblement, dans l’ensemble des Appalaches du nord. Les gîtes aux environs de Clarence Stream dans le sud-ouest du Nouveau Brunswick sont un exemple de ce type de gisement, mettant en valeur ce qui pourrait devenir un district aurifère majeur dans la région."

Jan 1, 2008

By E. W. J. Thornton

During the past six or seven years extensive research has been performed on ore samples procured at the Bruns1,vick Tin Mines which is located in the south-west corner of New Brunswi.ck. This property was originally staked by Mount Pleasant Mines and they did considerable metallurgical and geological work on a small copper, zinc and tin deposit. In 1969, the property was obtained by the Sullivan Mining Group and after much geological and diamond drilling work, an entirely separate ore body \Vas located two miles south of the previous workings. The major economic metals in this ore zone are tungsten, bismuth and molybdenite, but many other metals exist as well. As the ore contains a host of different mineral species, it can be seen that considerable time WRS required to develop a practical flow sheet.

Jan 1, 1977

By B. Konda, R. Lauer, D. Camilucci, D. Gladwin

"Income based taxes are significant cost elements to be considered in evaluating investment in new mine development. This paper presents the results of comparative analysis of effective income-based tax rates for mining in the Northwest Territories (NWT), selected Canadian provinces and international jurisdictions. The study was done as background to a review of royalty regulations for the NWT. ObjectiveThis paper presents results of comparative analysis of effective mining royalty1 rates, and combined effective mining royalty and income tax rates on selected mine models for the Northwest Territories (NWT), with those for several other jurisdictions in Canada and abroad which compete with the NWT for mining investment.BackgroundThe February 27, 1995 federal budget directed the Department of Indian Affairs and Northern Development (DIAND) to proceed with a comprehensive review and amendments to northern natural resource management legislation in order “to increase revenues and ensure a fair return to the Crown.” DIAND is responsible for the administration of the Territorial Lands Act, and its regulations.The Territorial Lands Act gives the Governor-in-Council the authority to “… make regulations for the leasing of mining rights in, under or on territorial lands and the payment of royalties therefor,…”. In the NWT, the Canada Mining Regulations (CMR) provide for the disposition of mineral rights for most minerals, other than coal, petroleum and related hydrocarbons, in return for the payment of a royalty to the Crown.As part of this review of the NWT mining royalty regime, several computer mine models were developed and tax regimes in a number of jurisdictions were analyzed. Effective mining royalty rates, and the combined effective mining royalty and income tax rates were compared across the jurisdictions. The results presented in this paper are a part of the background work done in preparing a discussion paper on proposed changes to the NWT mining royalty that is expected to be released for public consultation in the very near future."

Jan 1, 1997

By D. G. Hulbert, J. H. Schubert, R. G. D. Henning

"Froth depth, along with reagent addition and aeration rate, is one of the crucial factors that can be used to control a flotation circuit. Sub-optimal setpoints and disruptions in levels have a severe adverse influence on grades and recoveries. A novel control strategy has been developed which provides exceptionally tight regulation of pulp levels. The controller observes and acts on all the flotation levels simultaneously. This provides a clear improvement over the standard approach, which is to use a set of Pl controllers. The system has been run on several industrial plants and has resulted in reduced fluctuations in level; fast responses to setpoint changes, and fast settling times after start-ups or disturbances. Testwork has shown that the improvements in level stabilisation translate into improvements in recovery and grades.IntroductionProcess control and optimization have an important influence on the economic efficiency of flotation plants. Inefficient operation can allow the wrong balance between grades and recoveries, and can also lead to adverse shifts in the grade-recovery relationship. Of all metallurgical operations, flotation loses the largest proportion of valuable material. Better operation can reduce these losses.An essential requirement of a good controller is that it should be able to stabilize and regulate the plant. Stable operation allows the performance of the plant to be observed without being obscured by the effects of disturbances and fluctuations. The optimum conditions can then be detected more easily. Good regulation can maintain operation at the optimum with proper neutralization of disturbances. Only when good stabilization and regulation are achieved can an optimizing strategy be properly applied.Froth depth, aeration rate and reagent addition are the three means by which a flotation plant is generally controlled. These control actions are effective on different time scales. Reagent addition is slower in its effect as some conditioning time is required. Since reagents are only added at the head of the circuit and at a few selected points within the banks, time is required for the effect of reagent changes to move through the circuit. Because of this slower time constant, reagent addition is more suited to process optimization and to dealing with slower changes in the process. An example of these slower changes is variation in the feed."

Jan 1, 1995

By Ken Dyck Sr.

"Construction of the Cigar Lake uranium mine in northern Saskatchewan is well under way. Production is anticipated to begin in the first half of 2007. When in full production, the mine is projected to produce a net 18,000,000 pounds of U3O8 per annum from a high grade ore averaging approximately 20% U3O8.Water management was a major issue that required substantial effort in the Cigar Lake design. Not only is effluent quality controlled, a tight water balance to minimize effluent volume is also designed into processes in order to minimize environmental impact. This paper focuses on the water treatment process and water handling equipment, as well as the operating philosophies that will reduce fresh water consumption to a minimum. An overview of the mining and ore handling systems, as well as aspects of controlling water production from the ore formation and the mine development areas will also be discussed.INTRODUCTIONThe Cigar Lake ore body has proven and probable reserves that total 232 million pounds U3O8. Cigar Lake is the world’s largest undeveloped high-grade deposit. It is the second largest highgrade deposit surpassed only by the McArthur River deposit another Cameco - operated mine in the Saskatchewan Athabasca Basin. Cigar Lake is owned 50% by Cameco Corporation, 37% by AREVA (COGEMA Resources Inc.), 8% by Idemitsu Uranium Exploration Canada Ltd. and 5% by TEPCO Resources Inc. When production starts in 2007, ground ore slurry from Cigar Lake will be shipped to the McClean Lake mill (owned by AREVA) some 80 km away. All of the Cigar Lake uranium will be leached from the ore at McClean Lake. During initial production ramp up, all uranium will be processed at McClean Lake to yellow cake (uranium oxide). After the average production has exceeded a 10 million pound per year rate, Cigar Lake uranium will begin to flow from the McClean Lake Mill to the Rabbit Lake Mill. At this point, subject to regulatory approval, 57% of the Cigar Lake uranium, in a uranium rich solution, will be transported to Rabbit Lake mill (owned by Cameco) for purification to yellow cake. A complete summary of the flow of uranium from the Cigar Lake ore body through to product at both McClean Lake and Rabbit Lake can be found in a recent paper titled “The Cigar Lake Project – Mining, Ore Handling and Milling” in the March 2004 issue of the CIM Bulletin. The paper was written by C.R. Edwards."

Jan 1, 2006

By William Pitman

Ground instability and subsequent rock falls are a major concern in underground mines. As a result, several mining companies are conducting risk assessments of the ground support installed in their mines. Risk assessment is now commonly used to provide mine operators with a systematic process to assess the strategic risks that could lead to injury to personnel or loss of production, and evaluate possible risk control measures. Risk assessments can be carried out to identify major hazards, assess the likelihood of occurrence and consequences of each hazard and estimate the level of risk. This process allows assessment of possible remediation actions to minimize the risk and likelihood of occurrence or mitigation of the consequences to a level that is reasonable and practical. This paper presents two practical mine applications of qualitative risk assessment of ground support to highlight the benefits of this process. Yearly or bi-yearly risk assessment of mine excavations can assist mine operators in prioritizing resources and areas that require support remediation. In addition, it provides a mechanism for proactive response to reduce potential risks associated with personnel safety, equipment safety and environmental impact. It also provides a baseline against which changes in ground condition can be compared and quantified.

May 1, 2004

By Lachezar Tsotsorkov

Corporate social responsibility Is a principal trend of the corporate strategy for sustainable development of Assarel-Medet JSC ? the largest Bulgarian company for open pit mining and ore processing the production activities of which date back to 1964. Sustainable development Social responsibility is considered as one of the three pillars for sustainable development, together with the economic and environmental responsibility.

Aug 1, 2013

By Alan Galley

CMIC Mandate CIM Annual Meeting, Toronto, May 6, 2013 To increase mining research, innovation and commercialization efforts in order to strengthen Canada?s pre-eminent role as a global leader in mineral exploration, mining and knowledge-based services and technologies. To increase the supply of highly qualified graduates from mining and earth sciences faculties to meet the significant demand today and into the future of industry, governments and academia. The CMIC initiative is intended to develop long term research strategies that extend five or greater years. Such a research plan will underpin fundamental research and innovation and the training of HQP

May 1, 2013

By R. W. Pugh, D. G. Bellow

"This paper will describe how cultivator shanks are made in one company and how the manufacturing was studied with a view to increasing product consistency and reducing manufacturing cost. The product: which is used extensively in the agriculture industry, was analyzed to determine which geometric parameters optimized its design and whether there was justification for the great variety of styles and shapes that are available in the market. Finally, an extensive series of field trials were undertaken which showed that it is advantageous to the manufacturer to be better aware of the loads and forces that his product is subjected to by another industry.IntroductionStelco maintains a Research Group for its Western Region operations headquartered in Edmonton, Alberta. Because of the small staff, a location that is isolated with respect to its Burlington, Ontario centre and a diverse set of processes and products, a university relationship has developed which may be different from that which would be developed at a larger integrated Steel Works. This paper outlines the type of cooperative studies carried out by Stelco Inc. in Edmonton and the University of Alberta. .To meet the research needs covering a wide variety of steelmaking processes and steel products produced in Edmonton would require more staff and equipment than the sales volume in the West justifies. The gap is filled by cooperation with university personnel. This cooperation has provided these benefits to Stelco Inc.:• access to specialized test equipment and a trained staff to operate it; and• assistance from experts in the areas of product testing and problem solving.Moreover, the close proximity of the university to the plant allows frequent meetings and ensures that practical solutions are developed and implemented. A good example of the ongoing university I industry relationship developed is the joint work on improving cultivator shanks."

Jan 1, 1982

By P. P. Rosario, D. M. Maijer

The primary crusher is a key component in the comminution process applied in open pit mines. A collaborative research project between the University of British Columbia and Highland Valley Copper (HVC) was conducted aiming at understanding gyratory crusher liner wear in the overall context of the crushing process. This paper presents an analysis methodology applied to data collected using a laser-based tool for assessing wear in gyratory crushers. Data from the wear measurements was correlated with crusher production information such as current draw and throughput. As a result of the knowledge developed during this work, an innovative way to evaluate crusher liner profiles was created and new mantle profiles were designed. This led to a reformulation of HVC’s standard liner management policy with a resulting estimated annual savings of 13% in total crusher liner cost and a 15% reduction in liner replacement downtime.

Jan 1, 2006