Search Documents

By B. T. Lu, J. L. Luo, H. X. Guo

This paper investigated the synergistic effect in the slurry-erosion process of carbon steel. In line with the mechanisms of material loss, the synergism due to interaction of erosion and corrosion was divided into the corrosion enhanced by erosion and erosion enhanced by corrosion. The erosion-corrosion tests were conducted with A1045 steel in slurries containing silica sand. Experimental results showed that the rotating of the sample in corrosive media raised both OCP and corrosion rate, but the impingement of solid particles did not affect the corrosion current significantly. In the quiescent solutions, the Faraday's law gave a good prediction for the weight loss caused by corrosion but for rotating samples, the weight loss experimentally measured was virtually greater than that predicted by the Faraday's law, indicating that the corrosion-enhanced erosion could occur in corrosive fluids in absence of solid particles. A half-logarithm relationship was observed between the weight loss due to corrosion-enhanced erosion and the anodic current density.

Jan 1, 2004

By G. R. Guillet

Important resources of kaolin, refractory clay and lignite, not found elsewhere in Ontario, occur with quartz sand of glassgrade quality in unconsolidated Mesozoic sediments of the Moose River Basin in northeastern Ontario. These materials comprise the Mattagami Formation of Lower Cretaceous age, which overlie in some places a thin Jurassic unit and a thick Paleozoic section, and underlie as much as JOO m or more of glacial and marine sediments and a uniform capping of muskeg. The Mallagami Formation is known from deep boreholes to exceed 100 m in thickness and to consist of two phases: an earlier Type A unit of dark-coloured carbonaceous clays and lignite, and a later light-coloured (Type B) unit of kaolin-bearing quartz sands and bright-coloured refractory clays. Remoteness, poor access, and difficult physical environment have inhibited the exploration and development of these resources.

Jan 1, 1984

By Brian Penney

"The Iron Ore Company of Canada (IOCC} has mined and processed an iron deposit in Western Labrador along the Labrador-Quebec border since the early 1960' s. Current capacity is approximately 19 million tonnes of concentrate, 70% of which is converted to pellets at these facilities.The ore deposits are located in hills rising 150 to 300 meters above the adjacent lakes, and most of them are covered by very little overburden. The iron minerals are mainly specular hematite and magnetite hosted in a quartz formation. Crude ore averages 40% Fe that is concentrated to 65.5% Fe. IOCC is an extensive operation extending from Labrador City NF to Sept-Iles Quebec. It consists of open pit mining, concentrating, pelletizing, railway, and dock loading facilities.The Concentrator liberates iron from the silica by crushing and grinding the ore to -14 mesh (-1190 microns}. Ground ore is concentrated in spirals and filtered for transportation. Spiral tailings are treated in a Magnetic Recovery Plant (Mag Plant} that recovers lost magnetite. Mag Plant tailings are treated in a Hematite Spiral Plant (Hem Plant} that scavenges fine iron remaining in this stream.This report deals with ongoing iron recovery initiatives within the ConcentratorIron Losses in the ConcentratorIron recovery at IOCC is approximately 70.5%. This compares with recoveries that range from 65% to 86% for other iron mines in our area. Other world large iron ore producers dig and ship concentrate quality ore directly out of the ground and have an effective recovery of 100%. With increasing costs for labour, equipment, and supplies an increase in iron recovery is required to keep the operation viable.More than 90% of our iron concentrate is produced by gravity separation using spirals. The physical characteristics of the iron minerals that most effect recovery are mineral grain size and degree of liberation. We divide ground ore into three size categories -coarse, intermediate, and fines. A brief description of each size fraction follows:"

Jan 1, 1996

By Rene A. Morin, John K. Kebe

"As explosives become more widely used in urban and other congested areas, governmental regulations pertaining to their use are becoming more pervasive and stringent. This is forcing the blasting industry to review its entire spectrum of operations. Greater attention is now being paid not only to the design and layout of blasts, but also to the monitoring and recording of their after-effects for both legal and business reasons.Current PracticesThe major users of explosives in urban areas are quarry operators and construction companies. A characteristic of both of these industries, at least in recent years, is a relatively low margin of profit. This, coupled with the fact that their use of explosives is relatively intermittent, prevents them from having the kind of professional consulting services that blasting operations really warrant in today's regulatory environment. When such services are obtained, they tend to be directed more at the design and execution of the blast than at the recordkeeping function. The records that are kept tend to be more in the form of a summary of the consultant's design data as opposed to the kind of after-effect detail that is necessary.The more experienced consultants and operators now realize that at least as much attention must be paid to the record-keeping as to the design work. Regulatory bodies at all levels of government are insisting on the availability of such records.Unfortunately, the instrumentation in use today for taking such measurements does not lend itself to the practice of intermittent consulting. Current monitoring and recording instruments are based on so-called analog technology of the type that has traditionally been applied to the monitoring of earthquakes. They require set-up and calibration procedures which must be repeated each time the instrument is moved, or the blasting parameters are changed, as well as complex total analysis of the recorded data. This can lend to confusion and a dilution of responsibility for anything other than the design work and possibly some summary reporting."

Jan 1, 1985

By J. R. Perumareddi, V. S. Sastri, M. Elboujdaini

It is well known that high strength steels used in aerospace industry, are generally susceptible to hydrogen embrittlement during surface treatment such as electroplating with zinc on cadmium. Hydrogen embrittlement reduces ductility and results in brittle fracture rather than failure by plastic deformation. Hydrogen embrittlement of high strength steels is mitigated by surface treatment such as plating with other metals. Data on the hydrogen contents of steels before and after surface treatment by hot extraction-thermal conductivity, secondary ion mass spectrometry (SIMS) and UV-visible spectroscopy along with the mechanism are presented.

Jan 1, 2006

_What is standard technology infrastructure _ Business Context _ The mine operator?s technology challenges and needs _ The benefits of technology standards _ Overview of the SMART initiative _ Technology standards description _ Current status _ Next steps What is Standard Technology Infrastructure Technology Infrastructure is: ? Networking communications ? Computing operating systems ? Hardware platforms ? Data storage and access ? Operator interface _ These components are based on recognized open standards organization, and _ Commonly and widely utilized by industry, and _ Commercially available off-the-shelf systems (COTS), both hardware and software _ Standard capability to provide immediate and open access to raw or derived data at source, APIs, configuration parameters & sub-routines from all system components; ALL CURRENTLY AVAILABLE

May 1, 2008

By D. S. Robertson, G. E. Nutter, T. P. Podolsky

"IntroductionBasal Proterozoic quartz-pebble conglomerates are found both west of Elliot Lake, in Duncan, Jarvis and Aweres Townships, north of Sault Ste. Marie and to the east and northeast of Sudbury, Ontario. Locally, while well packed and pyrite-rich, they carry little to no uranium. Locally, they carry gold. These features generally are ascribed to variations in the source areas of the rocks.In two other areas of Canada, similar basal Proterozoic units contain quartz-pebble conglomerate beds with uranium.Sakami LakeLocation and HistoryThe Sakarni Lake uranium deposit is found in a narrow, northeast-trending, Archean greenstone belt located 95 miles southeast of Fort George, on James Bay, and 240 miles north of Matagami, Quebec (Fig. 1).The deposit was detected by Inco in 1971, during an airborne EM survey which carried a newly developed Inco spectrometer system flown at 450 feet. Ground investigation, in 1972, resulted in the discovery and sampling of quartz-pebble conglomerate which yielded assays as high as 0.19% U3O8.Extensive field exploration was conducted between 1972 and 1975. Sixty-five diamond drill holes, to a total of 13,969 metres, served to define the extent and economic potential of the conglomerates which extend over a total strike length of about eight kilometres."

Jan 1, 1986

By Brian Lewis

"IntroductionThe ion exchange process is classed as a purification and concentration stage. In the uranium industry it is used to separate, and recover uranium, from a solution produced in the leach and subsequent solid washing circuit, that contains uranium as well as some impurities. The final product from this circuit is a solution, containing uranium at a 15 to 25 fold increase in concentration, with a chemical composition suitable for the ""Precipitation"" circuit.The process is a reversible chemical ""ION"" exchange, between a solution, and solid phase, with the ""resin"" being the solid phase. Various chemical changes in the solution phase will permit the resin to remove uranium from a solution or have the uranium removed from the resin back into a solution phase. The former loads uranium onto the resin, and is called the ""adsorption cycle"", and the removal or stripping is known as the ""elution cycle"".Ion Exchange resin is a semi-rigid polystyrene spherical bead, approximately 10 to 30 mesh. It is used by placing the resin in a vessel, so that a porous bed of resin is formed, through which the solution may flow.There are many different types of vessels, and systems used to hold the resin, but it is not the intention of this chapter to describe them all, but to describe two methods used in Elliot Lake. These are the ""fixed bed"", and ""moving bed"" systems, the condition of the bed during normal operation signifies the name of the system.Chemical and Physical Characteristicslon Exchange ResinThe resin used is a strange base Anionic resin, semi-rigid, and spherical in shape. The size of the wet resin is approximately 9007o between 20 and 40 mesh. Physically the beads of resin are broken early, but some have lasted over 15 years and are still in use."

Jan 1, 1989

By A. G. Pentland

PROSPECTING is popularly supposed to be surrounded with an air of romance and adventure. The word 'prospecting' brings to mind high mountains, northern lakes, and aeroplanes. A note of urgency has been added to this by the war, particularly in the case of strategic, minerals. Prospecting for strategic minerals in a modern mine in full production, although it may Jack the romance of travel in little-known places, has the advantage of having all the necessary machinery at hand and ready to go into action at a moment's notice. HISTORY Tin was discovered in the Sullivan ore in 1925, when a white streak was noticed on a pilot table which was being used to check the amount of galena in the tailing. The mineral which made up this streak was identified as cassiterite. The amount of tin in the ore is so small that, while of scientific interest, it was considered to be of very little economic importance. Nevertheless, several attempts were made to learn something of the occurrence during times when other work was nor pressing. These studies were dropped when anything came up that seemed more important.

Jan 1, 1943

By Jianzhong Liu

Based on the characteristics of overburden rock strata movement, surface ground subsidence and casing deformation and failure, a tension-shear combination failure model of surface borehole was set up. The main controlling factors of the mining-induced deformation and failure of surface borehole were researched with this failure model and the limit analysis method. The mining methods and geology conditions mechanics action mechanism to surface borehole and its time ?space evaluation rule was found. The surface borehole deformation and fracture rule were advanced. It provides theoretical support to optimizing layout, structure type, security measure and local casing protection of surface borehole.

Aug 1, 2013

By H. Clare Horwood

"Two structures, a fracture zone and a shear zone, contained the two orebodies that yielded all the ore mined at the Gold Eagle mine. The orebodies are known as the Gold Eagle vein and the No. 1 shear zone. Both structures occur close to contacts between Timiskaming sediments, Algoman diorite, and later Algoman granite-granodiorite. The structures were produced by compressive forces from a south direction acting in the southern part of the McKenzie-Gold Eagle stock and in a cylindrically shaped inclusion of Timiskaming sediments.The mine, which exhausted its ore reserves and ceased operations in September of 1941, is on the east side of Mackenzie island, in the centre of Dome township in the Red Lake area.The Gold Eagle vein was located during the summer of 1933 by a surface exploration programme carried out under the direction of Alex Gillies. Sub-· sequent diamond drilling and underground exploration led to the installation of a mill, which came into production in October of 1937. The No. 1 shear zone was discovered and explored later from a drive on the 500-foot level. The mine produced a total of 40,204 oz. gold and 19,157 oz. silver from 223,628 tons of ore hoisted (180,095 tons milled) during its 4 years of mill operation.GENERAL GEOLOGYThe ore-bearing structures trend S.61°E. across Timiskaming greywacke, Algoman diorite, and later Algoman granite-granodiorite. The greywacke is a large, cylindrically shaped mass that is separated from the mai~ mass by the later intrusives. It is a massive, light-coloured, quartzose variety that has been recrystallized by the enclosing granite. The diorite and the granite-granodiorite are early and late components of the McKenzie-Gold Eagle stock. The diorite, which is a porphyritic rock containing large crystals of andesine-labradorite surrounded by hornblende, was injected early in the Algoman period. It was intruded and in large measure surrounded by the later granite-granodiorite. This rock varies from a granodiorite near the mine to a granite in the centre of the stock. All three intrusions are massive and homogeneous."

Jan 1, 1954

By J. E. Nesset

The past 50 years have been a golden era, not just for the CMP but also for the development and success of Canadian technologies in the field of mineral processing. The CMP has played a critical role of technology transfer agent, and the success of these technologies is also linked to the success of the CMP itself. The presentation will cover, in brief, the growth of the CMP from its origins as the Canadian Gold Metallurgists in 1964, with some 39 attendees, to the present day when the annual meeting sees 500 and more from a dozen countries. Also covered will be selected technology success stories from the 50th anniversary volume to be given to all delegates ‘Canadian Contributions to Mineral Processing Technology 1968-2018’. The volume itself highlights some 40 technologies that have been divided into five categories; process water treatment and minesite environment, technology innovations, innovations in operations, technology providers and university contributions. Some international perspectives will also be shared.

Jan 1, 2018

By Y. C. Kim

This paper discusses Air Liquide's patented SPALTM (Surface Protection Air Liquide) technology and process for the inerting of coreless induction furnaces using cryogenic liquid gas. Air Liquide Canada Inc., in collaboration with Riverside Brass and Aluminum Foundry Limited (Riverside Brass), conducted plant trials to demonstrate the applicability of the SPALTM technology for copper-based alloys. Results showed that with SPALTM, Riverside Brass benefited from a significant increase in metal yield as the level of dross formation was drastically reduced. Together with the many other benefits of this technology, SPALTM demonstrated to be a non-negligible cost-effective solution to reduce metal production costs. In an effort to optimize the argon flow, different flow rates were used and the oxygen level above the metal bath was measured to pinpoint optimal flow. The results of metal yield, charge mix, dross formation, and melt temperature are compared with and without argon. The metal yield improvements are dramatic and calculated net savings are presented hereunder.

Jan 1, 2007

By W. Beres, Li. J.

The finite element method (FEM) has been applied to investigate the stress fields and deformation of a TiN/Ti-6A1-4V coating/substrate system subjected to nanoindentation. MSC Patran and MSC Marc were used to prepare the three-dimensional finite element models and to perform the simulations of the Vickers nanoindentation experiments. Pure silicon and TiN/Ti-6A1-4V coating/substrate system were analyzed. The properties of the materials were assumed to be homogeneous and isotropic with a linear hardening behavior. The reverse method was used to extract material properties, such as the yield stress and strain hardening coefficient, from the numerical results by comparing the simulated indentation load vs. penetration depth (P-h) curves with those obtained experimentally. Both non-linear elastic and non-linear elastic-plastic analyses were carried out for the coating/substrate system. The results are given for four different coating thicknesses.

Jan 1, 2004

By J. Moyes

The Intec Copper Process is an internationally patented hydrometallurgical process for the extraction of pure copper and precious metals from sulfide concentrates. Developed and proven in Sydney, Australia at a cost of US$15m over the last ten years, the Intec Copper Process is now ready for commercial application. The Intec Copper Process has several notable advantages over both smelting and other hydrometallurgical processes. Starting from a base of substantially lower capital and operating costs than any other conventional or developing process, the Intec Copper Process is economically viable at capacity levels as low as 15,000tpa-Cu, and capable of accepting low grade and metallurgically complex concentrates. Precious metals are recovered within the Intec Copper Process circuit, without the need to re-treatment of the environmentally stable solid residues. The Intec Copper Process offers the lowest energy consumption of the available technologies, with no liquid emissions or production of noxious gases. Unlike smelting, sulfur is recovered in the solid residues in elemental form.

May 1, 2002

By K. Madi, E. Yeugo Fogaing, S. Forest, M. Boussuge, L. Massard, M. Huger, Gaultm C.

This study has been carried out owing to the French research program PROMETHEREF, which aims to improve the knowledge of thermal and mechanical properties of industrial refractories at high temperature. In this frame, this paper relates a collaborative study between Saint-Gobain CREE, R&D Centre for Saint-Gobain Ceramics & Plastics in Europe (Cavaillon), the Materials Center P.M. Fourt of Ecole des Mines de Paris (Evry) and the Research Group on Heterogeneous Materials (GEMH) of ENSCI (Limoges). Data collected at high temperatures by using different means (bending tests, ultrasonic measurements,...) allows the identification of the high temperature behavior of two fused cast materials, produced by Saint-Gobain group for the glass manufacturing industry. The results emphasize the importance of the transformation of zirconia and of the viscosity of the glassy intergranular phase on the mechanical behavior. Damage under the form of microcracking caused by thermal expansion mismatch between the phases is also observed during cooling down at low temperature, when the material is elastic.

Jan 1, 2004

By S. A. Beeson, C. Poole

"This paper reports on the development of selective flocculation processes for the direct recovery of KCl values from low-grade Canadian sylvinite and carnallite potash ores.Two reagent suites, consisting of either a non-selective cationic or selective non-ionic flocculant, together with the same selective anionic dispersant, were evaluated. Initial data from component mineral behaviour investigations, reagent adsorption studies and selective flocculation tests on a synthetic potash ore were used in the successful development of processes capable of recovering KCl values without the necessity for desliming to remove water-insolubles.Enhanced multi-stage treatment (involving redispersion and reflocculation) and subsequent floc recovery techniques (including sedimentation, hydrocyclones and froth flotation) were examined, and in all cases the influence of process parameters such as reagent dosages, conditioning times, solids concentration, particle size and other physical design criteria were investigated.The data reported clearly demonstrate the scale-up potential of these processes and possible applications in potash operations."

Jan 1, 2000

By Marcel Vallée

Abstract -Traditionally, samples collected for mineral deposit evaluation have been viewed without explicit reference to reliability, with the illusion that a true value is attainable from a few samples and verifications. For exploration, mineral deposit estimation and production quality control the following definition is proposed: "a sample is a small quantity of material relative to the geological mass it represents, collected according to a systematic procedure, of measurable reliability, from which the grade/quality of the mass which it represents may be estimated, based upon appropriate protocols. This paper will concentrate on the actual rock sampling process. Too often, sample size has been, and is still viewed as a matter of convenience, leaving out representivity considerations, despite the importance of samples on project estimation. Linear samples (chips, channels, drill), panel samples, broken rock or mining samples and very large samples are considered. Collection procedures and quality control protocols to improve the representivity of non-mechanical samples are proposed.

Jan 1, 1998

By F. Shi

The JKRBT (JK Rotary Breakage Tester) is a newly developed impact breakage testing device for rapid ore breakage characterisation, and has recently been commercialised after a three year comprehensive validation study, involving five major mining companies and six industrialised JKRBT units deployed worldwide. Comparisons of breakage mechanisms and characterisation data between the JKRBT and the Drop Weight Tester (DWT) indicate that, despite the differences in the breakage modes, the JKRBT can provide statistically similar A*b parameters, by using a data reduction procedure which takes into account the difference in the number of contact points, strain rate and potential for secondary breakage. Feedback from the validation sponsors has indicated higher productivity and better repeatability of the JKRBT compared with the DWT. This better precision, combined with the JKRBT’s wider particle size capability and wider specific energy range, provide a more powerful tool, ideally suited to rapid mapping of ore hardness in geometallurgical and comminution applications.

Jan 1, 2012

By Sadan Kelebek, Gerhard W. Heinrich, Peter F. Wells, Peter J. Whittaker

"Based on plant mineralogical data & circuit modelling, a pilot plant campaign was conducted at Strathcona Mill to identify options for improving the performance and operating flexibility of the copper-nickel separation circuits. Emphasis was given to options for combined treatment of the two feed streams (primary nickel ore rougher concentrate and copper ore circuit concentrate) to obtain more flexibility in the use of existing column flotation capacities. The pilot test results demonstrated that circuits which incorporated preconcentration prior to column flotation gave the best metallurgical results. Maximum column carrying rates were also related to the preconcentration. Predictions that increased circulating loads from the column scavengers would improve copper-nickel separation performance were confirmed.IntroductionThe copper-nickel separation circuits at Falconbridge's Strathcona Mill produce a high grade (>30% Cu) copper concentrate most of which is treated at the Falconbridge Kidd Creek smelter near Timmins. The remaining nickel concentrate which still contains approximately 20% of the feed copper is combined with other lower grade nickel/copper concentrates and shipped to the Falconbridge nickel smelter. The separation is required because of the limited capacity for copper processing in and downstream from the nickel smelter. Since no nickel is recovered at present in the Kidd smelter, the challenge is to minimize the nickel content of the copper concentrate.At present there are two independent separation circuits treating the rougher concentrates from the copper and nickel circuits as shown in Figure I. The minerals treated are mainly chalcopyrite and pentlandite but there is up to 25% of the copper present as cubanite in the copper ore. The circuits were kept separate because the flotation rates and froth characteristics were very different, probably because of the presence of cubanite and the large difference in the concentrate grades feeding the circuits."

Jan 1, 1995