Search Documents

In-Situ Leaching (ISL) process plants are low cost producers for uranium deposits where the geology is suitable. In the 1970s, a three-year pilot ISL program occurred on gold ore from the Ajax Mine, Cripple Creek District, Colorado, using a chloride and iodide solution [1]. The test was halted due to poor results. With gold and silver the international ISL progress has been slow; however the potential for low capital expenditure (CAPEX) and operating expenditure (OPEX) with large low grade deposits is real. Unless the metallurgy has been demonstrated there are significant risks which could be fatal flaws to an ISL gold or silver project. The metallurgy of gold ISL projects is far from simple and it is early days with project development.

Jan 1, 2011

By E. Ghali, C. Su, G. Houlachi

"The influence of lead ions on zinc electrowinning process was investigated by means of electrochemical noise measurements (ENMs) and cyclic voltammetry in conjunction with scanning electron microscopy and X-ray diffraction. All electrochemical experiments were performed in sulphuric acid electrolyte containing different lead ion concentrations as impurity. Lead was added in six trace levels between 0.05–0.8 mg/L in the bath. The lead content of the zinc deposits was dependent on the introduced lead concentrations. The overpotential associated with zinc electrodeposition shifted to higher values with the increase of lead concentration in the solution. An appropriate correlation was found between the different concentrations of lead in the electrolyte and the morphology of zinc deposit by ENM. The results showed that the increase of lead ion concentrations is generally accompanied with the decrease of skew and increase of kurtosis values that could be related to the morphology of zinc deposit. Effectively, the morphology changes from well-defined hexagonal platelets to large hexagonal, layered platelets and finally to non-symmetric refined crystalline structure, respectively.INTRODUCTION In commercial zinc electrowinning, zinc oxide is leached from the roasted calcine with an aqueous acid sulfate electrolyte. Then the zinc-rich solution is purified and transferred into an electrolytic cell. During electrolysis, zinc is deposited on aluminum cathode where lead-silver or pure lead is served as anode. Electrodeposition of zinc could be influenced by several parameters such as bath acidity, temperature, current density, the nature and concentration of impurities as well as additives in electrolyte. Metallic impurities play a complex role during zinc electrowinning and they can adversely"

Jan 1, 2016

By Jerry Ran

When multiple levels are mined in open stope mining with delayed backfill, mining underneath fill is inevitable to achieve higher rate of recovery if no sill pillars are left for the purpose of fill separation or partial ground support. This is particularly true when the orebody has low reserves per unit vertical distance. Instability of the exposed fill back causes stope dilution, production delay and possible equipment damage and consequently increases the mining cost. Previous studies have concentrated on fill mat stability in cut-and-fill and stability of fill walls in open stope mining. Workers are exposed to the fill back in cut-and-fill and therefore smaller open spans are normally adopted and the fill mat is reinforced. In open stope mining openings with large spans are designed, workers are not exposed to the fill back and its stability has to be maintained by fill of sufficient strength. However, the required fill strength is normally determined by considering different modes of fill wall failure. The fill back stability is usually not analyzed in the fill design process. The lack of analysis on fill back stability for open stope mining is mainly due to difficulties in relating the fill properties to the fill and stope geometry. In this paper a simplified wedge model is adopted to analyze stability of the exposed fill back in open stope mining with consolidated backfill. The proposed method calculates the factor of safety of the fill back against shear failure under known fill and stope geometry and fill strength parameters in order to assess the fill back stability. It can also be used to determine the required fill strength with known fill and stope geometry. The proposed approach is indirectly validated by mining experience and observations at two operating mines. In addition there are many factors affecting the fill quality and stope configurations in an operating mine. These factors have to be considered in the analysis of fill back stability. This situation is highlighted by presenting an actual mining case where the fill back failed due to factors commonly encountered in mining operations.

May 1, 2003

By Franc R. Joubin, Donald H. James

"The Algoma (or Blind River) uranium district is centred in an area of some 600 square miles on the north shore of Lake Huron, about half way between Sudbury and Sault Ste. Marie, Ontario (Figure 1). Its favourable location, adjoining the main provincial highway and Canadian Pacific Railway line which follow the lake shore, has contributed greatly to its rapid development.By Canadian standards, the district has long attracted geological attention, beginning with the discovery of the Bruce mine in 1846. It has been repeatedly prospected at intervals since then, chiefly for copper and nickel but also for lead, zinc, cobalt, silver, iron, and gold. Numerous discoveries have prompted the suggestion by Yates (13) and others that one metal-logenic province embraces the entire mineralized area from Michigan through Sudbury and Cobalt.Geological mapping was initiated by Murray in 1847, and the area attracted much interest as the type locality of the Huronian, the correlation and stratigraphic position of which are still not entirely agreed on. Subsequent contributors to the geological literature of the area have been very numerous, and the bibliography at the end of this paper includes only some of the more modern reports.The history of uranium in this part of Ontario also dates from 1847, when J. L. LeConte identified as uranium-bearing a pitchblende-like mineral which he named ""coracite"". The specimens came from Theano Point, north of Sault Ste. Marie. In 1948 a search for the source of these specimens led to the discovery of the Camray uranium field. Occurrences in this field consist of numerous small and locally rich pitchblende-bearing fractures, within or along the contacts of diabase dykes cutting Archaean granite and gneiss.None of the showings explored proved large enough to justify production, but they stimulated prospecting of adjoining areas and thus led to the Algoma discoveries.The first find of radioactive conglomerate in place was made in 1949 in Long township, and it was partially staked as the Fisher-Audette-Breton property. Rusty, overgrown rock-cuts indicated that the pyrite-bearing conglomerate had been investigated years before, probably during searches for base metals and gold. Examinations were made at this time by a number of geologists, including the senior author. In spite of high radioactivity, sampling returned only negligible uranium. The claims were allowed to lapse and the showings reverted to obscurity."

Jan 1, 1949

By B. D. Thompson

Many mines adopt necessarily conservative backfilling strategies due to a lack of understanding of their backfill behaviour. In the past five years, extensive instrumentation campaigns have focused on measuring in-situ cemented paste backfill behaviour. These tests have resulted in optimised backfilling efficiency through elimination or reduction of cure periods where; i) controls on backfill behaviour are understood, and ii) barricade pressures are demonstrated to be within a safe range using routine monitoring as a required QA/QC procedure. Recently, this work has been extended to consider hydraulic backfill operations. Two stopes have been instrumented at Vale?s Coleman and Garson Ramp mines. The instrumentation and deployment methods are discussed, and representative total earth pressure, pore pressure, and temperature data are presented. In one case, pressures in the stope are relatively low as drainage causes strength gain in the fill and so pressures are arched. In a second example, again, drainage causes strength gain in the fill, but increasing temperatures correlate with pressure increases even during downtimes in filling. These pressure increases are thought to be caused by thermal expansion of the backfill in confined locations. Generally, the instrumentation approach has proven successful in measuring hydraulic backfill behaviour and offers good potential for incorporation into a procedure to safely maximise backfilling efficiency through routine barricade pressure monitoring, when combined with safeguards to ensure adequate fill drainage.

Aug 1, 2013

By Mohamed Hamoud

Relative permeability curves represent an important element of special core analyses, but challenges remain in obtaining valid results and the extrapolation and use of existing permeability results is problematic. This situation is compounded in cases where core properties are altered from changes in effective stress. During the production of oil and gas reservoirs, the effective stress changes as a result of changes in pore pressure or temperature. Therefore, changes in rock properties such as porosity and permeability will occur and will consequently influence reservoir performance calculations. An experimental program was carried out to understand the behavior of dense, reconstituted sand samples at low effective stress states. Drained triaxial compression tests were set up to study the effect of stress alteration on relative permeability data through porous media. Initially, a saturation stage was performed followed by isotropic loading to bring the core sample to reservoir fluid and stress conditions. Then, while axial (deviatoric stress) loading was applied to the sample, a series of absolute and relative permeability tests was performed under steady state flow at different levels of strain during pre and post peak shearing stress. The stress-strain behavior results from the study revealed that the absolute permeability decreased during isotropic loading (compaction) and increased during shearing (dilation). However, the shape of relative permeability curve changed from contraction to dilation and showed higher initial kro and the lower initial kro respectively. The goal of this project was to understand the behavior of both absolute and relative permeability at different stresses. It is expected that geomechanical processes will be adopted for special core analyses to support the current integration of geomechanics into reservoir engineering. This will be required if, during SAGD, conventional and/or unconventional reservoir simulation, reservoir engineers implement a proper set of relative permeability data at each in situ state of stress, instead of constant curves throughout the field?s life.

Jun 1, 2012

By C. Gu

Flow field design is critical for PEM fuel cells. The flow field design can affect reactant distribution to the catalyst surface, water management, thermal management and current collection. Therefore, it has tremendous impacts on the fuel cell performance and durability as well as reliability and operational flexibility. In this paper, an optical method is used to study the reactant distribution in the flow field channels of two commonly used flow field designs, straight channel design and serpentine channel design. Images of the flow patterns are shown followed by discussions of the flow patterns.

Jan 1, 2005

By B. Tougas

Recycling of titanium represents an important economic activity due to high cost of the material and the amount of returns of machined parts which represent the bulk of finished titanium products (typical "buy to fly" of 10 in the aeronautic industry). In the present work, the metallurgical quality of 76 mm in diameter and 20 cm ingots poured in coated graphite mold will be assessed against the nature and condition of application of 4 coatings namely aluminum oxide, yttrium oxide, zirconium oxide and zirconium oxide with 4% aluminum oxide. The metallurgical quality has been evaluated in terms of alpha case thickness, microstructure and composition. Microhardness from surface will be assessed against casting conditions. Least square regression analysis have been use to optimize casting conditions.

Jan 1, 2011

By Renato Macciotta

The argillaceous formation known as the Opalinus Clay is host to the Mont Terri Underground Research Laboratory. The URL was developed to investigate the hydrogeological, geochemical and geotechnical properties of the formation. Underground excavations at the site are characterized by non-elastic and time-dependent deformations. Excavations trending perpendicular to the strike of the bedding presented relatively minor deformations, however, tunnels parallel to the strike of the bedding showed much larger non-elastic deformations. This paper presents an analysis of the measured response of a tunnel trending parallel to the strike of the bedding in Opalinus Clay. The measured convergence is compared to tunnel experience in weak rocks to assess the tunnel stability.

Jun 1, 2012

By Kevin Azocar, Jim Hazzard

"Slope stability analysis is performed most commonly using limit equilibrium calculations or numerical models assuming a two-dimensional slice through an infinitely long slope surface. In areas such as open pit mining, where most slope surfaces are not planar, the importance of curvature becomes important due to the economic gains associated with creating a steeper slope. With advances in computing capabilities within the last decade, three-dimensional slope analysis can be performed within reasonable time frames. Some work has been done on the potential importance of curvature on slope stability, mainly assuming homogenous materials with a circular shear-failure mechanism. However, many open pit mines are excavated in jointed rock mass where a completely different set of failure mechanisms can be seen. Depending on the geometry and radius of the pit, the curved geometry may influence the factor of safety and failure behaviour compared to a two-dimensional slice.A series of numerical analyses were performed to investigate the effect of curvature on jointed rock slope stability compared to an equivalent two-dimensional slope analysis. By using discrete element method models, the influence of joint planes and interaction between distinct blocks can be seen. With a three-dimensional model, the effect of curvature can be combined with multiple joint sets at any orientation, which cannot be seen in a single slice. Numerous three-dimensional models are created, along with an equivalent unit-thick slice. The effect of curvature on a variety of different types of failure mechanisms is observed, and graphical relationships are created to quantify the difference between the three-dimensional factor of safety and the two-dimensional factor of safety based on the degree of curvature."

Jan 1, 2015

By K. B. Han, S. Winkler, M. J. Benoit, M. J. Worswick

"Automotive heat exchangers are fabricated by forming multi-layered aluminum (Al) alloy brazing sheets into the desired geometry and subsequently passing the assembly through a furnace for brazing. As manufacturers seek to use thinner gauge and higher strength sheet to reduce vehicle weight, forming of the Al alloy sheets has become a challenge. Warm forming has previously proven to allay these forming concerns, but no consideration was given to the effect of increasing the forming temperature on brazing. Recently, it was shown that annealed sheet was more susceptible to the detrimental phenomenon of liquid film migration (LFM) during brazing if formed above 150°C, while work hardened sheets showed no increased susceptibility to LFM with increasing forming temperature, up to 250°C. In the current study, the brazing performance of simulated battery cooling plates was investigated. The plates were fabricated both from fully annealed and work hardened sheets. Brazing was assessed by microstructural evolution during a brazing cycle. The post-brazed microstructure varied with strain and forming temperature in plates made from annealed sheets, while no variation in microstructure with location or forming temperature was observed in plates formed from work hardened sheets.INTRODUCTION Since the 1970’s, one common method of fabricating automotive heat exchangers has been by forming multi-layered aluminum (Al) alloy sheets, and subsequently brazing the formed components together in a controlled atmosphere furnace. The Al alloy sheets used are comprised of at least two Al alloys roll bonded together, but can consist of additional layers, depending on the application; at minimum, the sheets are comprised of a core and clad layer. The core layer, often an AA3xxx alloy, remains solid throughout processing and provides strength to the assembly. The clad layer is always one of the AA4xxx series alloys which, due to their high silicon (Si) content, have a melting temperature range well below that of the core alloy. When the sheet is passed through the brazing furnace, the clad alloy melts to provide the brazed joint filler metal throughout the assembly, while the core alloy remains solid. In order to achieve cost and weight savings, heat exchanger fabricators have used Al alloy sheets with reduced thickness. However, deformation and brazing of these increasingly thin components remains a concern (Zhao & Woods, 2013). Furthermore, springback has been observed after forming sheets of higher initial strength (i.e. work hardened conditions), leading to flatness issues of formed components. Consequently, the ability to form high quality brazed joints is difficult in components formed from higher strength brazing sheets."

Jan 1, 2018

By D. Letzig

Wrought magnesium alloys are of special interest as lightweight structural components as a result of their more homogeneous microstructures and improved mechanical properties compared to cast components. Extrusion as a shaping technology offers the possibility to produce a wide variety of magnesium alloy profiles. In this contribution we describe the role of extrusion parameters such as extrusion speed, ratio and temperature as well as the type of extrusion process on the microstructural development of AZ-series magnesium alloys and the resulting mechanical properties. The effect of microstructure on the tensile/compression deformation behavior of the alloys has also been investigated. Aspects of process optimization designed to overcome technical and economic limitations and thus establish magnesium alloy profiles for industrial applications will also be discussed.

Jan 1, 2006

By Paolo Farina

Slope monitoring radar has emerged in the last ten years as a leading edge tool for monitoring movements in natural and engineered slopes, thanks to its ability to rapidly measure slope movements with millimetric accuracy over wide areas in any weather conditions, obviating the need to install artificial reflectors. In recent years, slope monitoring radar has experienced significant improvements in its performances, mainly thanks to the use of different radar technology, such as Synthetic Aperture Radar (SAR), able to overcome some of the limitations of the first generation of radar and to provide higher spatial resolution, longer working distances and faster acquisition time. One of the leading applications of this technology is today represented by slope monitoring within the surface mining industry. Prominent international mining groups currently employ slope monitoring radar, based either on Real Aperture Radar (RAR) and SAR technology, for active and background monitoring of open-pit walls. The main technical features of typical slope monitoring radar based on SAR technology along with their possible applications are presented in this paper along with recent case studies of successful slope monitoring in open pit mines.

Jun 1, 2012

By S. Nakamura, K. Fujiwara, S. Hirosawa, S. Tsukamoto, Y. Koshino, Y. Aruga

"In this study, hardness test, differential scanning calorimetry(DSC)and transmission electron micros copy were carried out to investigate the age-hardening behavior of Al-Mg-Si alloy with a Mg+Si concentration of 1.5mass%, and a Mg/Si ratio of 1.0. Pre-aging treatment was conducted for the solution-treated and then water-quenched specimen at 100, 80, 60, 40, 20 (natural aging), 0 and -20°C for 20min or 5h, followed by artificial aging at 170°C for 20min. It was found that when pre-aging time is prolonged from 20min to 5h, the bake-hardening response is deteriorated irrespective of the pre-aging temperature. In particular, the specimens subjected to pre-aging at 20-40°C for 5 h hardly increased the hardness with the subsequent artificial aging. From the results of DSC measurement, it was suggested that as pre-aging temperature is lowered, the amount of solute clusters formed during pre-aging, i.e. Mg-Si clusters and Si-rich clusters, is decreased, but the ratio of Si-rich clusters is increased, resulting in the deteriorated bake-hardening response.INTRODUCTIONIn recent years, Al-Mg-Si alloys have been widely used forautomotive body panels due to their excellent characteristics such as high strength-to-weight ratio and good formability. Their strength is increased not only by artificial aging during paint-bake treatment; i.e. “bake-hardening”, but also when kept at room temperature(RT);i.e. “natural aging”, in association with the suppressed bake-hardening response. Such a “negative effect of two-step aging” has been a serious problem because Al-Mg-Si alloy coils are unavoidably maintained at RT in the manufacturing process of body panels; e.g. shipping and storage. However, it was reported that pre-aging above 70°C before the two-step aging can restore the bake-hardening response, and such an improvement is related to the formation of solute clusters(Sato, 2006; Abidet al., 2010; Takaki et al., 2014; Zandbergen et al., 2015). From the comprehensive analysis by three-dimensional atom probe (Aruga et al., 2014 and 2015), it is believed that Mg-Si clusters formed during pre-aging transform into the strengtheningß"" phase, whereas Si-rich clusters formed during pre-aging act as a detrimental precursor of ß""phase. In this study, it was aimed to investigate the effect of pre-aging conditions, especially pre-aging temperature and time, on the formation of solute clusters during pre-aging, in order to elucidate the mechanism of the age-hardening behavior of an Al-Mg-Si alloy."

Jan 1, 2018

By R. A. Sudisman, T. Yamabe, M. Osada

"Geological material can be subjected to some different loading conditions, mainly due to three inter-related physical processes which are mechanical, thermal, and hydrological. Freezing and thawing process of rock that occurs in sub-zero temperature condition may contain some or all those three physical processes depended on its initial condition. Those inter-related physical processes may lead the ground into failures. Therefore, understanding the physical properties such as deformation process of geological material under freezing and thawing condition is required for the artificial ground freezing projects and engineering construction activity in the natural cold region.In order to study the strain characteristic of rocks during freezing and thawing process, a series of freezing and thawing experiments of core samples of three different rock types and mortar has been conducted under varying temperature from -20 °C to +20 °C. Four core sample types are Sandstone, Granite, Tuff, and Mortar with 50 mm diameter and 50 mm height, which were naturally dried before the freezing-thawing experiment. Freezing-thawing experiment was conducted by submerging the vinyl covered core samples into a temperature-controlled liquid coolant box. Firstly, temperature of liquid (brine solution) was set at -20 °C so that the temperature of subjected sample was decreasing to as low as -20 °C. And then the temperature of brine was returning to initial room temperature after the coolant system was stopped. Strain gauge and thermo couple were attached on the core’s perimeter to measure strains and temperature changes.Sandstone and Mortar samples show relatively similar results than other two samples. Both presents linearly shrink with the temperature decrease and expand almost to its initial condition with the temperature increase. Granite shows less-linear strain-temperature relationship during thawing process, while the Tuff sample shows abrupt strain increase during thawing process on the temperature higher than +10 °C. Thermal expansion value of each rock types were obtained by fitting the major strain-temperature relationship on -19 °C to +10 °C temperature range. Overall, anisotropic deformation was observed on the entire samples and possible mechanisms for each hysteresis characteristic are discussed, which need to be confirmed by further experiments."

Jan 1, 2015

By Baisheng Nie

The process of gas diffusion through coal particles and the mathematical physical model under the third kind boundary condition was determined to obtain the rules of gas diffusion through coal particles of different sizes. The analytical solution of the equation was obtained by the Method of Mathematical Physics. The parameters of analytical solutions and the implications of parameters were analyzed. The Biot criterion (Bi) and the Fourier criterion (F0) of mass transfer can represent and reflect the features of gas diffusion field of coal particles. Moreover, the measurement method of gas diffusion coefficient and surface mass transfer coefficient is introduced and an example of measurement is given. The achievement can provide the support to prevent disasters related to methane in coal mines.

Aug 1, 2013

By W. A. MacWilliams, R. G. Reynolds

"This paper describes, for the first time, a patented method of extracting sodium sulphate from a natural deposit in Western Canada. The method resembles, but is not, strictly speaking, solution mining. The fact that a plant based on this method has been in successful operation since late 1969 will be of added interest. The deposit in question is located near Metiskow, Alberta, and conventional surface recovery methods could not be applied because of heavy concentrations of mud. Considerable pilot work went into the separation and recovery process on which the plant operation is based. The history of the industry is covered briefly as background to this development. Today it is clear that the method has broader application within the industry and, in concept, may generate interest in many other applications."

Jan 1, 1973

By I. Yarita

Magnesium alloys have the lowest density among the metals in practical use, and have properties such high specific strength, electromagnetic interference shielding and good vibration damping. Thus, there are many applications of these materials in automotive and electric parts. However, there is a little use of the products of metal forming of these materials because of poor plastic deformability in the normal temperature range and their high cost of production. To expand the range of application of products manufactured by metal forming, rolling technology for producing thin sheets having good mechanical and surface qualities is required. In this study, hot-rolled Mg-alloy sheets are experimentally rolled with or without lubrication in the temperature range from 293 K to 523 K. Rolling force, plastic deformability and surface quality are investigated, and the grain structures and their uniformity are observed. The effect of friction between the roll and the deforming material on the uniformity of the grain structure is discussed. Moreover, rolled materials are annealed and their mechanical properties are investigated by the tensile test and compared with those of as-rolled materials. The effects of the rolling conditions on the mechanical properties are discussed.

Jan 1, 2006

By P. R. Stephenson

Mining projects depend on the amount and quality of the mineral reserves, which in turn depend on the amount and quality of the mineral resources. Only Measured and Indicated Resources may be converted to mineral reserves and Inferred Resources may not, with certain exceptions, be used in economic studies. Responsibility for the estimation of mineral resources rests with the Qualified Person (QP) and there is a wealth of literature, text books and case studies to guide the QP. Responsibility for the classification of the mineral resources also rests with the QP. While there is some industry guidance and common practice on approaches to resource classification on which the QP can draw, the process is (or should be) heavily dependent on the exercise of judgement by the QP. However, this inevitably leads to situations where, for example, one QP?s Inferred Resource is another QP?s Indicated Resource. If the QP?s judgement is poorly reasoned or illogical (as is sometimes the case), it can have a major impact on the project, often with substantial cost or value implications. Project managers and company executives should not unquestioningly accept QP?s classification decisions and should apply the same intensity of due diligence that they apply to other critical elements of the project.

May 1, 2011

By Muhammad Zaka Emad

Cemented rockfill (CRF) plays a vital role in pillar-less mining. Many factors are associated with optimum design of a CRF material. Factors like strength, placement method, mixing, curing time, water content, binder contents, binder composition and additives require to be studied for appropriate rockfill design. The most important factor is strength of a CRF. The design engineer considers fill strength requirements (FSR) for the estimation of CRF strength requirements. Inappropriate CRF strength can cause excessive ore dilution. The recent studies on CRF practices at some of the Canadian mines revealed the most common flaws. Comparison of different types of fill determined that most of the failures occur in cemented rockfill, and the compressive strength can be improved by small addition of sand and mine tailings. This work discusses the studies on determination of unconfined compressive strength, Young?s modulus, density and water contents of CRF being placed in the excavated stopes. It was found that the CRF properties were largely influenced by the variation in gradation and curing time. The 7% binder content improved compressive strength of rockfill significantly but it has an influence on the economics, whereas 4% and 5% binder contents are better choices. The maximum Young?s modulus values were obtained at 28 days curing time for most of the samples.

May 1, 2011