Search Documents

By C. Cortés

Flotation is a highly interactive process where a change or disturbance in any part of the circuit results in different final grades and recoveries. This high variability of the circuit metallurgical performance complicates the diagnosis of the scavenger stage at the end of the line, as copper losses in the final tailings are erratic and not totally a consequence of problems in the scavenger section. The assessment of the scavenger performance requires a more elaborated procedure than that used for others stages of the circuit. This communication describes the application of an approach that combines results of laboratory flotation tests with those of surveys performed at the plant. The approach is based on running surveys in one of the circuit lines to collect samples for determining grade vs. recovery curves for total mass and size-by-size fractions. Full mineralogical and liberation analyses are also considered on some samples of the feed and tailings streams selected to have a range of feed grades. A separate sample of the feed is used to run laboratory flotation tests to determine optimum flotation time. Two additional pieces of information are the effect of operating variables on recovery, determined through a test program based on design of experiment techniques, and operational data on every cell in the line gathered by visual observation. The application of this approach to one of the scavenger lines at Los Colorados concentrator (Minera Escondida, BHP Billiton) is demonstrated.

Jan 1, 2007

By Youngsoo Song, Hyunjung Kim, Junhyun Choi, Siyoung Q. Choi, Gahee Kim

In this study, for the first time, to confirm the effect of bacterial growth phase on the malachite flotation were investigated in a well-controlled Hallimond tube system. The test results showed that the bacteria in the stationary phase exhibit two-fold greater floatability than those in mid-exponential phase. To understand the observed flotation behavior, complementary cell characterization tests and cell attachment tests were conducted. Interestingly, the bacteria at both phases exhibited similar surface properties as well as almost identical amount of cells attached onto the malachite, suggesting that the growth phasedependent flotation behavior cannot be attributed to the variation of cell surface properties and the extent of cell adsorption. On the other hand, cell detachment tests revealed that the amount of cells detached from the malachite surface is greater for the mid-exponential phase than the stationary phase due to the higher fluid drag applied to the cells at the mid-exponential phase, which was explained by the differences in the size and shape of attached bacteria onto the malachite surface. These morphological characteristics were found to cause the bacteria of mid-exponential phase to be separated highly sensitive and easy from malachite surface due to the fluid flow. Second, scale-up selective bioflotation tests were carried out in a 1 L Denver cell in malachite–silica binary mixture systems. Through the tests, we optimized the cell concentration and the malachite fraction in the feed. Overall, high malachite selectively was observed under optimized conditions (both recovery and grade showed more than 90%). The trend was in agreement with classical DLVO interaction energy profiles, which show the relative magnitudes of the adhesive forces between the mineral and the attached cell under equal hydrodynamic conditions.

Jan 1, 2016

By E. Ghali, B. Arsenault

Aluminum alloys play an important role in the manufacturing of air and ground vehicles. However, with such alloys, corrosion damage is often found on structural components subjected to fatigue loading. The alloying provides large benefit in terms of the high specific tensile strength (ultimate strength/density ratio) to the aluminum alloy but causes the aluminum alloy to be more sensitive to localized corrosion due to complex microscopic heterogeneities such as secondary phases. This paper investigates thermal spray coating namely arc spraying to evaluate the protection against environmentally assisted cracking (EAC) and localized corrosion on Aircraft structural 7075 T651 aluminum alloys. In particular, EAC and pitting corrosion at the interface coating-substrate are a challenge for thermal spray protective coatings on aluminum alloys under cyclic load and immersion. To address these issues, different surface preparation techniques prior to arc spraying were considered such as chemical de-oxidation, laser ablation, shot peening and grit blasting. Results indicate that surface preparation and improved coating process parameters play an important role to provide a coating conferring a protection against both localized corrosion and EAC.

Jan 1, 2006

By M. R. Julien

"The geomechanical behavior of rocksalt shows very distinctive features. The response of this most ductile of all low porosity rocks is dominated by inelastic processes that are strongly time- and historydependent. These characteristics must be taken into account when analyzing underground openings. Different constitutive models have been proposed and used for this purpose, and this paper presents the general formulation and applications of one of these. The SUVIC model relies on a unified approach with internal state variables producing mixed hardening to represent the inelastic behavior, which lead to specific solutions for plasticity and creep. The model equations have been implemented into a finite element code to perform numerical analyses. Simulations results are presented to show that this model captures essential aspects of rocksalt behavior under simple and complex laboratory testing conditions. Simulations are also conducted to analyze the response of underground openings. INTRODUCTIONPredicting the response of man-made excavations in rocksalt can be quite a challenge as it requires a reliable constitutive model to represent the material behavior. This softest of all low porosity rocks shows a highly non-linear inelastic behavior, very sensitive to history and rate effects (e.g. Senseny et al., 1993; Cristescu & Hunsche, 1997; Julien, 1999; Wittdke, 2014). The many deformation (micro) mechanisms acting locally in rocksalt make the construction of appropriate constitutive equations quite complex. Nonetheless, there have been significant progresses made over the last two decades or so; many of these developments have been included in a series of specialized Conferences Proceedings (Ghoreychi et al., 1996; Aubertin & Hardy, 1998; Cristescu et al., 2002; Wallner et al., 2007; Bérest et al., 2012)."

Jan 1, 2015

By P. E. Cavanagh

Abstract Many investigators have been interested in developing some non-destructive method for detecting or determining the changes in physical properties in steel occurring during endurance tests or normal service life of a part which fails in fatigue. This paper presents a broad discussion of some of this work and the possibilities of developing useful test procedures based on some of the information obtained in the past. Changes in magnetic properties, electrical resistance, damping capacity, X-ray diffraction patterns, and remaining fatigue life at load different from service load have all been investigated as possible means for following the sequence of events during fatigue failure. In some special instances, tests such as these may be used to predict fatigue failure. As an in stance of practical application of the continuous determination of changes in magnetic properties during fatigue, a brief account is given of work done in non-destructive inspection of mine hoist-rope. As a result of extensive experiments and field crisis, it has been found possible to detect the beginnings of failure in a wire rope in service. The test method used will detect plastic deformation in a wire rope, no matter what its cause. There is no possibility of determining the remaining useful life of a rope by calibrating changes in magnetic properties in terms of remaining fatigue life. A change in magnetic properties at a point in a rope may indicate a decrease or increase in fatigue life, depending on the overload history of the rope. A continuing change in magnetic properties ac a point, however, does reliably indicate a developing weak point which will eventually lead to failure. The important point about any change in magnetic properties is not the magnitude of the change, but whether or not it continues.

Jan 1, 1947

By I. Pérez-Rey, J. Arzúa, L. R. Alejano

"The decrease in strength with increasing rock specimen size is usually associated to the increase in the number of defects inside the specimens at small scale (centimeters) but also to the role of the rock mass structure at the rock mass scale (meters to decimeters).This matter of concern was particularly focused when determining the size of pillars in underground mines. Some formulae regarding strength of pillars have been proposed but they usually consider only the size and shape of the pillars and the strength of the intact rock. The structure tends to be overlooked or hidden behind the scale, but it is probably very relevant. For standard tunnel design, the approach by Hoek and Brown (1997), taking the structure into account in terms of the GSI, is commonly used. However, this approach does not specifically consider the size of the tunnel. Thus, a size larger than the so-called representative elementary volume is implicitly contemplated.The authors have recently performed a lab study on the effect of the structure in the strength, deformability and post-failure characteristics of granite at lab scale (NX size) extended here. This experimental program included intact and artificially jointed rock specimens. Obtained results permit to observe the changes in strength, deformability and post-failure behavior of this “small scale rock masses”, associating the role of the structure to the observed complete stress-strain response of the specimen, which can improve our understanding of the actual complete mechanical response of rock masses."

Jan 1, 2015

By S. M. J. Mirazimi, F. Rashchi

Recovery of vanadium from LD (Linz-Donawits) converter slag was evaluated by means of microbial leaching. Vanadium leaching was performed in two stages. In the first stage, the bacteria were grown in a culture medium and in the second stage; vanadium containing slag was added to the metabolites produced by bacteria. Bioleaching was performed using heterotrophic bacteria Pseudomonas Putída. Control tests without bacteria inoculation were also performed and the results were compared with bioleaching outcomes. Optimal conditions for the bioleaching of vanadium containing slag were determined.

Jan 1, 2011

By H. Dundar

The first application of High Pressure Grinding Rolls was in 1985 at a cement plant, for the purpose of capacity improvement. Then various circuit configurations were derived to achieve a reduction in overall specific energy consumption, by transferring more of the grinding required to the HPGR. In most circuit configurations, the recycle of fines is required for effective breakage between the rollers. By increasing the fines amount in the feed material to a specific level within the recycling load, a uniform material bed is created and a higher pressure gradient along the roller width is obtained, resulting in compact flakes, including more fines. The fines recycle results in enhancement of the interparticle breakage. This paper will discuss the effect of the feed size distribution on HPGR performance.

Jan 1, 2012

By Nigel Saunders, Zhanli Guo

"Quench sensitivity of heat-treatable aluminium alloys is closely related to the precipitation process taking place during quenching. Faster cooling results in less precipitation of coarse phases during cooling, leaving more solutes in the solution before ageing. An alloy in such state would be of greater hardening potential as larger amounts of hardening phases may precipitate out during ageing. Hence, to understand the quench sensitivity of an alloy, it is essential to understand its precipitation process. Precipitation is a diffusion-controlled process and the diffusion is made complicated by the so-called quenched-in vacancies. These vacancies form during solution treatment, become “excess” when temperature goes down, and annihilate during the following cooling and ageing treatments, making diffusion now a function of both temperature and time. This paper first investigates the formation and annihilation of quenched-in vacancies and their effect on diffusion. The diffusion affected by quenched-in vacancies is considered in the kinetic models to realise the calculation of TTT/CCT diagrams for aluminium alloys. The calculated CCT diagrams have been used to explain the observed quench sensitivity and age hardening behaviour of various commercial alloys. The transformation from GP zones to other hardening phases during ageing is also discussed.INTRODUCTION The heat treatment of aluminium alloys mainly consists of three stages: a solution treatment at an elevated temperature, quenching from this solution treatment temperature to room temperature, followed by an ageing treatment to allow the precipitation of strengthening phases(Davis, 1993).The following statements generally describes how quench sensitivity is observed in heat-treatable Al-alloys: faster cooling results in,(i) less precipitation of coarse phases formed at high temperature during cooling, (ii) more solutes kept in solution before ageing, and (iii) larger amounts of hardening phases being formed, i.e. a greater hardening potential. Thus, the quench sensitivity of an alloy is closely related to its precipitation kinetics."

Jan 1, 2018

By X. Cao, M. Xiao, M. Jahazi

Magnesium alloys have low hardness, wear, erosion and corrosion resistance. The repair of service-damaged aerospace components made of magnesium alloys is an attractive solution in terms of time and cost saving. The feasibility of applying laser beam technology to repair ZE41A-T5 magnesium alloy sand castings in the machined surface conditions was studied using a continuous wave 4 kW Nd:YAG laser system. The influence of process parameters such as laser power, cladding speed, wire feed rate and defocusing distance on the shape, size and area of single cladding beads is discussed using a process optimization software. Sound single clad beads with good geometric characteristics were obtained using strictly controlled laser process parameters. The overall results indicate that laser surface cladding using filler wire has the potential for repairing aerospace components made of cast magnesium alloys.

Jan 1, 2006

By L. Sun

A numerical model has been developed to study the air flow in the flow plate and gas diffusion layer assembly on the cathode side of a PEM fuel cell. The flow plate in this type of fuel cell often has serpentine channels and the porous layer is adjacent to the flow plate to diffuse the air to the catalyst layer. Flow cross-over of air through the porous diffusion layer from one part of the channel to another can occur. This flow cross¬over is a result of the pressure differences between different parts of the channel, and it causes the flow rate through the channel to vary with the distance along the channel. A numerical study of pressure distribution and flow cross-over through the gas diffusion layer (GDL) in PEMFC flow field using a serpentine channel system has therefore been undertaken to compare the cases of a single channel and two parallel channels, with the channels having a trapezoidal cross-sectional shape. The purpose of the present work was to study the effect of the flow plate geometry on the basic fluid flow through the plate. The flow here has been assumed to be three-dimensional, steady, incompressible, isothermal and single-phase. The flow through the porous diffusion layer has been described using the Darcy model. The dimensionless governing equations have been solved by using the commercial CFD solver, FIDAP. From the results obtained, it can be found that the single channel systems have greater maximum flow rate difference than the parallel channel systems under the conditions considered in the present study. Also, the size ratio R of trapezoidal cross-sectional shape has a significant effect on the flow cross-over and pressure variation in the flow field.

Jan 1, 2005

By J. Bardinas

"The use of autogenous mills has become widespread, owing to their capacity and favorable capital and operating costs. Optimal operation of these systems is critical, given their high energy consumption and effect on downstream processing. A considerable effort has been spent over the years in the development of advanced control systems to achieve a better performance in this regard. However, despite significant advances, the problem still remains challenging, owing to the nonlinear behaviour of the system with respect to the mill variables, and, the unmeasured ore variability come from the mine.The mill load, in particular, can be seen as a state variable of the mill, which could be important for; modelling and control, and, important insights into the mill behaviour. In this investigation, time series cluster analysis was performed using online mill load measurements in order to identify the different control states of the mill. More specifically, this time series was divided into short non-overlapping segments. A distance matrix was set up for each segment and the information was captured by means of textural features, similar to that used in multivariate image analysis. These wavelet and grey level cooccurrence matrix features could subsequently be used to rapidly identify the normal operating conditions from the feed disturbances in the mill.In principle, the methods and models presented here, once suitably validated and calibrated, could be used in online process monitoring of autogenous mills. They also could serve as a foundation for developing more advanced process control models."

Jan 1, 2016

By G. G. Campbell

"HistoricalBARYTES was mined in Nova Scotia as early as 1874 from a deposit at Five Islands, on the north shore of Minas Basin. The first record of the presence of the mineral at the Walton site appears in a report by Selwyn in l893, who states: ""Barytes in considerable quantity occurs in veins in lime-stones at Walton and Pembroke"". The exact site of the present workings was marked •on a map published by Fletcher in 1905.The economic •possibilities of this deposit, however, were not recognized until 1940, at which time we were at war with Germany, who up to that time had supplied 50 per cent of the world's requirements.At that time the Nova Scotia Department of Mines, recognizing the need for certain strategic minerals, induced Canadian Industrial Minerals, Limited, to send prospectors into 'the area to look for manganese. No manganese deposits were found, but a deposit of barytes was directed to their attention, and exploration and development work on the occurrence was proceeded with.IntroductionThe south shore of Minas Basin between the Avon river at Windsor and the Stewiacke river at Maitland has long been known as a potential source of mineral wealth. It had attracted the attention of mineralogists and in the past had produced considerable tonnages of manganese ore and gypsum. Depletion of ore in surface and near surface deposits resulted in a dwindling production, until today only deposits of gypsum are worked."

Jan 1, 1952

By N. Giguère

Until recently, the heat treatment of pressure die cast parts has always been considered unpractical because the solution heat treatment resulted in unacceptable blistered parts. This was due to the presence of massive porosity associated with the die casting process where the inflow of metal inside the mold cavity is extremely turbulent. With the steady improvement of foundry practices and the generalization of vacuum die casting, porosity defects have been reduced to the point that a partial solutionizing heat treatment can be applied without any damage to the casting. However the solutionizing temperature must be lower than that applied to macroporosity free castings and for much shorter time. The object of the present study was to determine the optimum solutionizing temperature that can be applied to aluminum 383 die cast brackets along with the optimal temperature and time of aging resulting in the highest improvement in mechanical properties (both strength and ductility). This was done by testing strength and deformation on the casting itself using a specially designed jig; the crushing force to deformation curve was analyzed so as to quantify the improvement in both strength and ductility gained with the partial precipitation hardening heat treatment.

Jan 1, 2011

By C. Juers

Laboratory chromate coating was applied on AM50 and AZ91D alloys and compared to phosphate-permanganate one. Evaluation of the corrosion behaviour was performed using electrochemical DC and AC methods in ASTM water D1384-87. This electrolyte was chosen because it was moderately aggressive and found to give generally good correlations with long period exposure results in atmospheric conditions. Electrochemical impedance spectroscopy was used to determine more accurately the corrosion rates from the analyses of the high frequency capacitive loop. Anodic polarization was applied in order to evaluate the pitting resistance of the different coatings. These results were correlated with weight loss data evaluated from experiments performed by immersion tests in ASTM water D1384-87 and climatic cyclic chamber tests.

Jan 1, 2006

By Mohammadreza Jalali

Alberta contains over 400 billion barrels of viscous crude oil in fractured carbonates but there is no viable extraction technology as yet. Petroleum geomechanics has become a vital part of the assessment of such hydrocarbon reserves, especially for naturally fractured cases, which are particularly challenging in terms of accurate recovery prediction because of joint fabric complexity and lithological heterogeneity. As a result of interconnected fractures, transport properties of fractures (mostly permeability issues rather than thermal effects) are affected by production and injection activities that change the pore pressures, temperatures, saturations, and effective stresses. Enhanced oil recovery methods involving massive amounts of fluid injection (hot or cold) at high pressure (pinj) may be used to mobilize and produce the oil; therefore, deeper understanding of the fractured systems is desirable. Pressure and temperature variations in a fractured reservoir change the in situ stresses in the reservoir and surrounding rocks; this affects fracture apertures, radically changing the bulk flow properties because flux rate is highly sensitive to aperture. Hence, coupled pressure, temperature and effective stress changes must be considered for fractured reservoirs under a thermo-hydro-mechanical (THM) coupling approach.A hybrid FDM/DDM coupled method is presented to couple pore pressure and stress around a fracture in an impermeable matrix block. Deformation and stresses are calculated in each time step and then fracture permeability, which is the most sensitive petrophysical parameter in fractured reservoirs, is updated based on the fracture aperture variation. This model is then verified with UDEC (Universal Distinct Element Code) which uses a discrete approach to cope with fractured rock mass behavior.

Jun 1, 2012

By David McMullen

Radiation plays a critical role in the thermal behaviour of hydrometallurgical process equipment. This effect is particularly important when designing refractory lined equipment used in pressure leach/oxidation processes. In order to simplify this non-linear mode of heat transfer, the effects of radiation had previously been incorporated in an equivalent convective film coefficient in finite element methods (FEM). This prior method omits the effects of radiosity, a critical aspect of radiation heat transfer, which affects the design of refractory lining systems in autoclave vessels. Given that 60% of the heat loss in actual plant practice of an autoclave is due to radiation, reliability in the FEM is therefore impacted. This study validates the use of radiosity in FEM through thermal loading using a combination of simple geometries to be applied to complex environments such as vessel nozzle clusters. The added benefits of using a radiosity load includes an increase in confidence in thermal distribution results, greater accuracy in determining appropriate refractory lining systems, weld overlay sizing, and increased accuracy in structural analysis.

Jan 1, 2014

A study was made to determine the effect of increasing concentrations of dissolved oxygen on the floatability of galena pyrite and chalcopyrite. Adsorption, flotation and contact-angle tests were done in deoxygenated, in air-saturated and in oxygen-saturated solutions. The results showed that the adsorption of collector increased as the concentration of oxygen increased. Adsorption followed the exponential law r = kC'/"• Discontinuities in the curves were observed after the adsorption of several monolayers of collector. Although adsorption increased with increasing oxygen concentration, the floatability of the pyrite minerals did not increase, because oxidation had adverse effects on the floatability of these minerals. The floatability of galena was maximum in oxygen-saturated solutions, pyrite was depressed and chalcopyrite was also slightly depressed. Contact-angle tests proved that a bubble could not be attached to large flat surfaces in deoxygenated solutions, because sufficient surface free energy was not available for adhesion after the deformation of the bubble. In the presene of air, all the minerals yielded the same maximum angle of 72 degrees, characteristic of isopropyl xanthate.

Jan 1, 1970

By Grazyna Zakrzewska-Trznadel

The paper outlines the main objectives of the project that concern the evaluation of the possibility of uranium production from indigenous resources since Poland enters the nuclear program. The best available technologies are considered for uranium extraction and obtaining the yellow cake - U3O8. Liquid-liquid extraction with novel extracting agents, as well as membrane processes for separation of by-products will be tested in course of the project. The technological part will be completed with techno-economical analysis. Acknowledgement The studies were supported by the POIG project, No 01.01.02-14-094-09-00 ?Analysis of the possibility of uranium supply from domestic resources?.

Aug 1, 2010

By John Monhemius

Looking back over the past half century, it can be seen that the growth in the importance of hydrometallurgy for the production of non-ferrous and precious metals almost exactly parallels the rise of the environmental movement and its principal NGOs, such as Greenpeace and Friends of the Earth. The paper will review important landmarks in the development of the science and technology of hydrometallurgy and show how many of these have been influenced by pressures on the industry brought about by environmentalists. Successful innovations as well as commercial failures will be considered and reasons for the success or failure will be analysed and lessons drawn to guide future developments.

Jan 1, 2014