Search Documents

By G. Lafont

Aug 1, 2013

By Finch. J. A., C. Perez, J. M. Ortiz, G. Cortes, A. B. Yañiez, F. Coddou, P. Morales, H. Elgueta

A campaign to perform characterization tests in a TankCell®-300 flotation cell installed at Chuquicamata Codelco's concentrator was conducted. The campaign included integrated gas dispersion measurements (gas velocity radial mapping and single point gas holdup and bubble size) and determination of frother concentration. Cell streams were sampled to assess metallurgical performance at the same time. The experimental program was designed to establish the bubble surface area flux operating range and its effect on performance, and the effect of using longer residence times and of a device designed to enhance mixing in the collection zone (FlowBooster(TM)). The gas dispersion results and their relationship to metallurgical performance are discussed.

Jan 1, 2009

By K. T. Aye

An investigation into the leaching of chalcocite and covellite in cyanide solutions at concentrations typically encountered daring gold cyanidation has been conducted. The results indicate that, for both minerals, the extent of leaching is greater under anoxic conditions, but is still incomplete even in the presence of free cyanide ions, with undissolved copper solids remaining in equilibrium with solution species. The speciation of the sulfur and cyanide reaction products in solution are interpreted in terms of the fast formation of a copper(I)- cyanide complexes in solution and a sulfur-rich copper(I) polysulfide solid phase, which then reacts more slowly to produce thiocyanate ions.

Jan 1, 2011

By L. Dufourm

This paper presents a review of plant layout considerations incorporated into recent designs of SAG/Ball mill circuits for two medium sized concentrators. The plant layouts presented and the design concepts discussed, relate to smaller SAG circuits, but can equally apply to larger milling circuits. Included are design concepts and ideas introduced by the various project teams, and the focus is on the primary factors of any layout design which are safety, constructability, operability, and capital cost.

Jan 1, 2012

By J. L. Jambor, M. J. Baker, M. J. Logsdon

"Abstract - Prior to the development of the Diavik Diamonds Project, baseline studies were conducted to determine the geochemical characteristics of four kimberlite orebodies as an aid in the design of both the water-management system and the facilities for containment of processed kimberlite and ore stockpiles. Materials tested included field samples of volcaniclastic and pyroclastic kimberlite, processed kimberlite (i.e., kimberlite ore which had been screened and washed as part of the processing procedure), and sedimentary mudstone (a minor xenolithic unit which was assimilated during kimberlite emplacement). Approximately 200 samples of kimberlite materials were collected as part of the geochemistry program. Test-work included whole-rock chemical analyses, acidbase accounting, kinetic leach tests using columns, and mineralogical analyses. Diavik kimberlite has major oxide and trace-element concentrations consistent with global averages for kimberlite. The mean total-sulfur content of the kimberlite material is 0.22 wt% S, but with a significant range. The kimberlite has an excess of carbonate minerals over sulfide minerals (average CO2 = 4 wt%, present mainly as calcite), and has a mean neutralization potential of 311 kg CaCO3 equivalent/tonne. A reactive form of framboidal pyrite associated specifically with the mudstone xenoliths is the primary source of sulfide-sulfur. Long-term kinetic tests confirmed the preliminary interpretations that were made from the static-test results. Kimberlite and processed kimberlite are net acid-consuming materials that produce alkaline drainages and have low but detectable leaching rates for SO4 and specific trace metals such as Al, Co, Cu, Ni, and Zn. If segregated from the kimberlite, mudstone xenoliths are acid-generating (pH = 3) and produce an effluent with elevated concentrations of SO4, Fe, Al, Cu, Ni, and Zn. The study demonstrates that xenolithic units in Diavik kimberlites have an important effect on the environmental geochemistry of the ore rock. The mineralogy and aqueous geochemistry of the kimberlite materials are such that they may not be suitable for general earthworks or as an alkaline agent and should report to an engineered facility to protect site water quality."

Jan 1, 2001

By Mohamed Sassi, I. Kolo, R. L. Sousa, R. K. Abu Al-Rub, Manhal Sirat

"Fractures induced by folds are pivotal in hydrocarbon exploration, ground water transport and harnessing of geothermal energy. This is because of the need to predict and understand fracture propagation in reservoirs which have folded rock formations. Despite its prominence, there is a lack of reliable numerical models for simulating fractures resulting from rock folding. This is partially due to the difficulty involved in fracture modelling. As a contribution to fold-fracture modelling, this work applies a coupled plasticity-damage model to rock fracturing and anticlinal folds. Parametric studies on a single folded layer give insight into the fold formation and behaviour. The anisotropic continuum damage model which considers both tension and compression is formulated using the power damage evolution law. For ease in formulation, strain equivalence hypothesis is adopted whereby the strain is the same for both damaged and undamaged configurations. Lubliner plasticity yield criterion is adopted for plastic deformation. The model is coded in Abaqus user subroutine UMAT and is applicable to quasi-brittle materials.INTRODUCTIONThe understanding of fractures in the earth’s crust helps in the prediction, evaluation and characterization of fractured reservoirs, whether they are petroleum, geothermal or underground water reservoirs. This is partly because reservoir permeability and stability are dependent on fracture properties (Nelson, 2001). To achieve this, various approaches have been developed to analyze reservoir rock fractures. These could be grouped into (a) discrete approaches – where the rock mass is represented by a finite number of well-defined components and (b) continuum approaches – where the mathematical assumption of an infinitesimal element is made (Jing, 2003). Ivanova (Ivanova, 1998) comprehensively studied fracture systems in nature and highlighted folds as one of the major geologic settings that produce fractures. Naturally occurring folds in reservoirs sometimes compound fracture analysis. It might not be clear whether the fractures formed before, during or after rock folding. Fractures formed during the folding process are expected to show stress orientations related to folding and are thus of primary concern in rock folding simulation. It could be argued that there are no numerical models that as"

Jan 1, 2015

By L. Xia, B. Hart, J. Nigim, Z. Chen

"Grinding ore is an important step in the flotation process. Not only does grinding reduce particle size and liberate minerals, it also creates conditions for reactions to occur on particle surfaces that can aide or inhibit flotation. There have been numerous studies examining various grinding regiments and the effect on flotation pulp chemistry, including autogenous grinding and using media of variable composition. There have been however, few studies looking at the effect of variability in grinding media size on pulp chemistry and subsequent flotation. This study attempts to link changes in pulp chemistry in response to variations in grinding media size to flotation recovery. It uses probes mounted in the grinding chamber (pH, Eh, DO, and conductivity) to monitor pulp chemistry changes during grinding of a Cu-Zn ore. Surface chemistry analysis by ToF-SIMS was performed on sphalerite from the mill discharge. Activator and depressant species were monitored on the mineral surfaces and their presence was evaluated in the context of variability in pulp chemistry linked to differences in grinding media and its ball size.INTRODUCTIONIt has been widely recognised that not only does grinding reduce particle size and liberate minerals but the grinding environment has a large effect on the flotation of sulphide minerals. This effect is attributed to Eh change, iron hydroxide coating on surfaces, oxygen reduction, precipitation from solution and galvanic coupling (Grano, 2009). As early as 1960, it was reported that after grinding the ores in an iron mill the natural floatability of sphalerite was reduced significantly (Rey and Formanek, 1960). Kocabag and Smith (1985) studied on the industrial circuits showing that the depression of sulphides flotation in a steel mill is possibly due to the coating of iron oxidation products. Peng, Grano, Fornasiero, and Ralston (2003a, 2003b) found that iron contamination from grinding media plays a dominant role in depressing galena and chalcopyrite flotation. Huang, Grano, and Skinner (2006) reported the same observation in the flotation of arsenopyrite."

Jan 1, 2016

By S. J. Buckler

Many metallurgical processes use submerged gas injection to increase the contact area between gas and liquid phases in order to promote faster overall reaction rates. The work presented in this paper is part of an experimental investigation to measure the gas-liquid interfacial area available in bubble plumes within molten metal baths. Measurements of the nitrogen absorption rate during submerged injection into molten iron baths have been used to estimate the interfacial areas of the bubble plumes. A theoretical model was used to predict the superficial nitrogen transfer rate under mixed liquid phase mass transfer -interfacial reaction control. The interfacial area was calculated by dividing the overall nitrogen absorption rate by the superficial rate. Reasonable agreement was obtained between the interfacial areas measured in our laboratory with data from a comparable system reported in the literature. The experimental results were compared with the predictions of three theoretical models and one empirical correlation. The models of Turkdogan (3) and Zhao and Themelis (5) gave the best agreement with our data.

Jan 1, 2004

By F. McIntosh Galbraith

EMPLOYING geophysics to find ore was for a long time considered by the Canadian mining fraternity to be a performance of dubious value: in a category somewhere between the practice of sorcery, and using a divining rod to locate underground water. With increasing knowledge, however, and with constantly improving instruments, a solid speaking acquaintance with this adolescent science is becoming an integral part of the mining geologist's stock in trade. And quite properly so: for, in the established mining districts, the ore deposits which could be easily found, by ordinary prospecting methods, have already been located. There remain; however, in almost all of the principal mining camps, areas which are covered to varying depths by glacial debris; and it is here that the obvious opportunities exist for the successful application of geophysical methods. Geophysical results must always be considered in the closest possible relation to the local geology; and, in reality, the 'doodle-bugs' are simply additional tools for the geologist (in the same category with a plane table or a microscope). The Sudbury Basin is a shining example of precisely this state of affairs. Detailed geological mapping has not significantly altered the position of the outer norite contact as placed on Dr. Coleman's original map of the district. What detailed examination has done, of course, has been to reveal the accuracy with which the contact can be placed in different parts of the district, and to show up, in consequence, areas in which further work might reasonably be expected to disclose hitherto unknown or unsuspected ore. Viewed in this light, the proportion of the norite contact which is covered by substantial quantities of overburden is astonishingly large.

Jan 1, 1939

By P. Homola, M. Karlík, M. Slámová

"Aluminum sheets (AA1199, AA8006, and AA5754) were processed by accumulative roll-bonding (ARB) in the temperature range from 20 to 350°C. The microstructure of the sheets was characterized by means of scanning and transmission electron microscopy and electron backscattered diffraction. Mechanical properties were monitored by hardness measurements and tensile tests. Increasing strain (number of ARB cycles) led to incremental development of lamellar microstructure with a decrease of the spacing between high-angle grain boundaries in the normal direction of sheets. ARB process produced an important increase of strength while maintaining thickness and relatively high ductility, without accenting of the anisotropy of mechanical properties of sheets. The level of hardening decreased with the processing temperature and at 300 and 350°C ARB caused even the softening of the material due to the recovery of the deformed microstructure or partial recrystallization during heating to ARB processing temperature.INTRODUCTION Accumulative Roll Bonding (ARB) is a technique of grain refinement by severe plastic deformation (SPD) proposed by Saito et al. (1999). One ARB cycle consists in sheet cutting, surface treatment, stacking of two pieces, heating (optional), and rolling with 50% reduction in thickness. Since the sheet thickness remains unchanged by this cycle, ARB processing can be repeated as many times as desired. The goal of ARB is to impose an extremely high plastic strain on the material, resulting in structural refinement and strength increase without changing specimen dimensions. After several cycles, ultra-fine grained (UFG) materials with high strength and relatively high ductility are produced. An advantage of this method is that it does not require any special equipment as other SPD methods such as equal channel angular pressing (ECAP) (Valiev & Langdon, 2006), high pressure torsion (HPT) (Valiev et al., 2000), or cyclic extrusion and compression (CEC) (Richert et al., 1999), but only a conventional rolling mill and so it is seen as an economically viable and industrially scalable processing route. ARB processing has been successfully applied to various kinds of metallic materials at room or elevated temperatures (Tsuji, 2005). Besides processing single metals and alloys, ARB has also been used for creating ultra-fine grained and nanograined metallic composites (Wu et al., 2010; Qu et al., 2014)."

Jan 1, 2018

By J. Ellis Thomson

For many years the value of qualitative microscopic investigation has been recognized in both of the fields of pure and applied science. In particular, its aid has been invoked in the determination of rock specimens in thin section, and some at least of the interrelations of minerals present in any one section have been observed and, to a limited extent, applied for the solution of different problems. During the past decade this form of research has also been diverted to the determination of ore minerals in polished section, with some observation of their structural relations. Microscopic research of a quantitative character, on the other hand, while started nearly one hundred years ago, has found but a limited application in petrography and has scarcely been used at all in the more modern science of mineragraphy. This is very largely due to the methods employed, since most of them consumed too much time and were, in addition, too laborious to encourage many workers in their use. The details of procedure for these earlier methods will be found in another paper by the writer, and will be omitted from this discussion as being of small interest to practical mining men.

Jan 1, 1930

By J. Kouam

Al-Si-Cu and Al-Si-Mg alloys are widely used in several applications. Although they can be produced near-net-shapes, products made of these alloys very often require some machining. The purpose of this study is to evaluate the machinability of A319 and A356 under TO and T6 conditions. The machinability was assessed using during dry drilling machining process and the machinability indexes used are the chip form, the chip breakability and the cutting forces. It is found that 319 and 356 exhibit different machinability behaviors, especially in the T6-condition in terms of forces requirements, chip breakability and chip segmentation. It is also found that both the microstructure of the workpiece materials and the machining conditions significantly affect the chip formation mechanism, and therefore, the machining parameters could be selected to promote a chip form that is easily manageable in production.

Jan 1, 2011

By C. Lara-Valenzuela, R. Perez-Garibay, F. López-Saucedo, A. Uribe-Salas, L. Magallanes-Hernandez

A relationship between gas dispersion parameters, namely gas rate (Jg), gas holdup (Eg), average bubble size (db) and bubble surface area flux (Sb), with the metallurgical performance (e.g., grade and recovery) has been established.. Results of eleven columns operating at five concentrators of Grupo Pefioles (Mexico), ranging between 1.52 to 3.35 min diameter and performing in the cleaning stages of lead and zinc circuits, are presented and discussed. The results showed that the effect of gas dispersion parameters was consistent and that both, Sb and Eg, correlate well with recovery particularly when the influence of feed pulp density is also considered.

Jan 1, 2009

By A. Bouajila

To stay competitive in an open market, mineral industries have to optimise their processes, lower their production costs and improve the commercial value of their products. Up to a recent past, they were impaired in this attempt by a lack of adequate devices allowing reliable on-line and real-time process monitoring (detection or measurement). Process monitoring for process control and the product characterisation for quality control are quite different tasks. Planners and researchers should be fully aware of this when evaluating or developing monitoring equipment for on-line process control. This paper will comment on some aspects of sensor specifications, during the design and the evaluation steps, related to sampling, measurement (accuracy, sensitivity, delay and correlation to the process) and suitability to the exploitation environment. Examples of R&D projects promoted by COREM for various industrial applications will be presented.

May 1, 2001

By M. Fairman

The effect of welding speed on the microstructure of friction stir processed (FSPed) AZ31B-H24 magnesium alloy was studied using light microscopy, image analysis, and microhardness tests. The grain size of the magnesium alloy was observed to increase after FSP from about 3.5 µm in the base alloy to about 8 µm in the stir zone. The aspect ratio decreased from 1.60 to 1.55 towards the center of the stir zone. The changes in the grain size and shape caused the microhardness of the samples to drop significantly across the FSPed region from 75 HV in the base alloy to below 55 HV in the stir zone. Decreasing the welding speed increased the grain size due to a greater input of heat energy. The faster heating rate due to the lower welding speed caused a deeper penetration of the annealing effects of FSP. It was also observed that the annealing effects caused by FSP were less pronounced with increasing distance from the interface between the sample and pin tool shoulder. The Hall-Petch type relationship of the micro-indentation hardness as a function of the grain size was observed to hold true after FSP.

Jan 1, 2007

By H. Fujiwara, T. Ito, T. Mizuguchi, K. Kawasaki

"In this study, we characterize the high-temperature deformation of typical “Class I” solid solution Al-Mg alloys as a superplastic elongation attributable to the solute drag creep of dislocations. The second-phase particles formed by adding Fe or Si as impurity atoms to the Al-Mg alloys impeded the gliding motion of dislocations, thereby decreasing their hot ductility and resulting in cavity formation. High-temperature tensile tests were performed with initial strain rates in the range of 1×10–3 to 1×10–1 s–1 at air temperatures 673–723 K. The dominant high-temperature deformation mechanism in these alloys was the solute drag creep controlled by the interdiffusion of Mg in Al. In this study, the calculation of critical length, defined by the diffusion-based relaxation of the stress concentration region around second-phase particles, is reported using the Needleman–Rice parameter. An analysis of the impact of cavity formation based on a comparison of the Needleman–Rice parameter and second-phase particle size is also reported.INTRODUCTION Aluminum alloys with high specific strengths are utilized as structural materials for transportation machines to minimize their weight, which consequently maximizes fuel efficiency, environment preservation, and so on (Miller et al., 2000; Heinz et al., 2000; Starke & Staley, 1996; Polmear, 1996; Immarigeon et al., 1995; Burger, Gupta, Jeffrey, & Lloyd, 1995; Ye, 2003). Microstructure refinement by severe plastic deformation (SPD) has been performed on a laboratory scale to achieve a higher strength of crystalline materials (Valiev et al., 2006; Song, Ponge, Raabe, Speer, & Matlock, 2006; Beyerlein & Toth, 2009; Sabirov, Murashkin, & Valiev, 2013; Sauvage, Wilde, Divinski, Horita, & Valiev, 2012). At room temperature, grain refinement strengthens the material, as given by the Hall-Petch relationship (Hall, 1951; Petch, 1953); at higher temperatures, superplasticity can be expected (Sherby & Wadsworth, 1989; Edington, Melton, & Cutler, 1979; Furukawa, Horita, Nemoto, & Langdon, 2001; Langdon, 2006). However, the synthesis of large-size materials by SPD processes is not yet feasible."

Jan 1, 2018

By Rod Maclean, George Stewart

"This paper covers the planning, development, and mining of an underground pillar complex using a bulk mining method. To achieve the long-term goal of continually improving our operating processes, all cut-and-fill and undercut-and-fill workplaces at Thompson Mine have been evaluated for their conversion potential to the bulk method referred to as VerticalBlock Mining (V.B.M.).Since December 1979, conversion has occurred to the extent where 80% of the ore hoisted is mined using Vertical Block Mining (V.B.M.).Productivity and profitability have been substantially improved by converting to this bulk method, especially in pillar areas.IntroductionThompson Mine is a 6000 ton per day underground nickel mine located 3 miles outside the City of Thompson, 400 air miles north of Winnipeg . The mine has two shafts, T-l and T-3 (Fig. 1). The T-l shaft is 4427 feet deep with the deepest mining taking place on 4000 level. The T-3 shaft, which is the area of this presentation, extends to a depth of 2607 ft with the deepest operating level at 2400 ft. The two shafts, some 10 000 ft apart, are connected underground on numerous levels. The ore mined at T-3 is trammed on 2400 level to the T-I main ore pass and hoisted through the T-l shaft. Eight hundred and fifty thousand cubic feet of fresh air per minute ventilates the mine.The 1400 level 310 pillar complex is located in the T-3 mine area. There are six rib pillars, two crown pillars and one main pillar (boundary pillar between cut-and-fill stopes) within the complex (Fig. 2). The majority of the ore in this area has been mined using mechanized cut-and-fill techniques .Undercut-and-fill mining was the method originally planned to recover these pillars. It is slow, labour-intensive, and requires extensive use of timber during the mining cycle. The extraction drifts in the area are heavily timbered due to their proximity to the ore and the age of the facilities. Increasing drift maintenance costs and the successful mining of two main pillars with V.8.M. techniques provided the stimulus to review the mining plans for this area."

Jan 1, 1988

By Frank Ebbutt

In this paper it is proposed to point out certain structural factors that; have an important bearing on gold deposition. The subject will be treated; more or less generally. Although the writer has had access to a great many; of Canada's gold mines he does not wish to take the liberty of discussing; details of any particular mine or mines; the aim will be to discuss controls; that are evident in many places.

Jan 1, 1954

By H. C. Cooke

"The Part of the Eastern Townships dealt with in this paper is shown in the accompanying figure. Each rectangle represents one of the topographic maps published by the Department of National Defence on a scale of one mile to one inch. Each sheet covers an area approximately 24 miles long and 17 miles wide, or slightly more than 400 square miles. The north-western part of the area figured, comprising the Upton, Aston, Becancour, and the two unnamed sheets, (Three Rivers and Yamaska), together with most of the Lyster, Drummondville, and St. Hyacinthe sheets, is largely covered by clays and sands deposited in interglacial and post-glacial time in the Champlain estuary, so that outcrops are widely scattered and in-formation is correspondingly sketchy. In the remainder of the area figured, comprising more than 4,000 square miles, outcrops are reasonably numerous and have been mapped on a scale of one mile to one inch, and the structure is moderately well understood.The Eastern Townships was an area of intense orogenic disturbance, apparently beginning late in the Cambrian or early in the Ordovician, and continuing till well on in the Devonian period. During this long period, which may have lasted for a hundred million years or more, the area was subjected from time to time to intense thrusts from the east and southeast. Each of these caused folding of the rocks, accompanied by faulting, raised parts of the area above sea-level, and presumably created ranges of mountains. Long periods of erosion cut away the mountains and reduced the area nearly to sea-level after which subsidence carried it below sea-level, and permitted further sediments to accumulate before the next thrust initiated the next cycle.The first of these movements, as stated, appears to have been in late Cambrian or early Ordovician time. The group of rocks known as Caldwell was folded and, south and east of the town of Asbestos, was thrown into great drag-folds before deposition of the next overlying series, termed the Beauceville, began. Unfortunately, the date of this orogeny is very imperfectly known, because both series of rocks have been so crushed and sheared that almost all fossil remains have been destroyed. Graptolites, found in one place in slates generally considered Beauceville, give that series a tentative Middle Ordovician age. In the Caldwell rocks, which underlie the Beauceville with great unconformity, no fossils whatever have yet been found. Thus, if the Beauceville rocks are correctly dated as mid-Ordovician, the best that can be said of the movement folding the Caldwell is that it took place at some time before Middle Ordovician."

Jan 1, 1949

By Jeremy P. Richards

Key inputs are volatiles and heat: Slab dehydration: Breakdown of amphibole and serpentine in hydrated oceanic crust releases fluids into mantle wedge, causing metasomatism.

May 1, 2008