Search Documents

By P. Patnaik, F. Cuneo, D. M. Wang

Microwave (MW) energy has been used widely for several decades for communications, food processing, wood drying, vulcanization of rubber and medical therapy. Recently, this technology was found to be capable of successfully sintering ceramic and metallic powder materials, with the advantages of reducing soaking times and sintering temperatures. Unlike conventional heating, MW radiation works through the absorption of the microwave energy by a material placed in an electromagnetic field within the microwave cavity. A far more efficient heating process is produced due to the unique ability of microwaves in selectively heating a pecific part of the material with desirable dielectrical properties. This exploratory research was initiated with the objective of locally sintering the thermal barrier coating of gas turbine components using MW radiation. This novel technique may allow repairing of the component without subjecting the entire piece to unnecessary elevated temperatures and reduction of process time and cost. Y ttria stabilized zirconia was used in this study and sintering was conducted using a multimodal 1.2 kW microwave facility. Three configurations of heating setup were experimented and the preliminary results will be discussed in this paper.

Jan 1, 2006

By M. Y. Williams

Introduction During the economic investigation of Pacific Great Eastern Railway subsidy lands, the P.G.E. Survey of Resources made a geological and mineral survey of a large part of the valley of the Peace river as included in the Province of British Columbia. The immediate valley of the Peace river was surveyed from the mountains to the Alberta boundary; the valley of the Pine river was surveyed throughout; and the Dominion block, 70 miles square and lying astride the Peace river, westward from the Alberta boundary, was very carefully surveyed. The writer was in general charge of the field work, and spent half the field season of 1929 and the field season of 1930 in the region . J. B. Bocock, however, did the major part of the work, spending two seasons, 1929 and 1930, in the area. General Conclusions The rock formations within the area discussed are all sedimentary and range in age from pre-Cambrian to recent. As might be expected, the minerals are in the main non-metallic, coal being by far the most important. Favourable conditions exist for natural gas occurrence, and suitable structures for petroleum concentration occur, although the high carbon ratio of the coals sheds considerable doubt upon the actual occurrence of oil in the area. Materials of minor interest are ochre, calcareous tufa, marl, limonite, gravel, and building stone.

Jan 1, 1934

By T. Patching

"MINING operations at the Star Key Mine provided an example of a small-scale prairie-type coal mine that employed several interesting procedures and achieved good productivity with low capital expenditures. The mine was located about 11 miles north of the city of Edmonton, on the north side of the Sturgeon River valley. It opened in 1945 and operated until 1979. Output in the winters reached about 500 tons a day in the late 1940s, but in the spring and summer periods activity was usually limited to only servicing and development work. In the later years of the mine's life sales fell to less than 100 tons per day. Most of its output was bought for domestic use in furnaces and stoves so production of large sizes was desired. A modest market for stoker coal did exist for a time. Screenings (-5 / 8 in.) were sold to the city's power plant until it converted to natural gas and were also used for thawing frozen ground for work on pipelines. These markets were comparatively small and the small sizes did not command as high a price as did the larger sizes. However the extension of natural gas services to rural markets cut into the domestic heating market and finally led to closure of the mine. The coal was strong when freshly mined, but because of its high inherent moisture content, about 25%, it did not store well on surface but tended to disintegrate. It was of subbituminous Crank with a heating value of about 8000 Btu per pound and burned with a clean flame. The seam mined was in the Edmonton Formation, of Upper Cretaceous age, at a depth of 60 to 80 ft below the surface. The seam in the mine area was about 11 feet in thickness but thinned gradually to the north and south and split to the west (1). It was approximately horizontal but gentle rolls in the floor of several feet in height necessitated brushing in places to produce suitable haulage grades. The floor material was of bone and clay, overlying a thin layer of coal. Above the seam there were only a few feet of mudstones and weak sandy shales while the remainder of the overburden was clay and unconsolidated glacial till and surface soil. Because of the soft floor and weak roof material the miners usually left about a foot of coal in the floor to provide a firm working surface and about a foot of coal above the rooms and two feet of coal above the entries to provide a competent roof."

Jan 1, 1985

By Luis Bergh, Juan Olivares, Juan Durán, Juan Yianatos

"In the last decades heuristic approaches based on logic rules have been one favored tool to control flotation units and plants on top of distributed control systems. Fundamental knowledge on flotation processes, expressed in reliable models, and programs to assure the quality of the information, contained in available measurements, are still insufficient to develop robust predictive control strategies. In this paper the idea of using simplified models, when a known disturbance is coming into the process, is explored. As a first approach, the set points of the froth depth and air flow rate controllers are estimated based on this model. Since these target predictions are only approximate, a conventional feedback expert system, based on logic rules, continues the task of calculating the set points of the distributed controllers, in order to decrease the gap between actual and desirable metallurgical targets. This combined actions permitted a fast response of the process to change the operation of the circuit when a measured disturbance is detected. This control system was implemented and experimentally evaluated in a pilot rougher flotation circuit, with three pneumatic cells, with froth depth and air flow rate controllers in each cell. Since the circuit is operated for the air-water system, a phenomenological model, with parameters estimated from industrial data, is fed on-line with real operating variables and virtual values, characterizing the feed (grades, solids%, particle size distribution), in order to predict the metallurgical targets (recovery and concentrate grade). Several cases are discussed showing the benefits of this control system and the possible improvements to work on. INTRODUCTIONToday, large size mechanical flotation cells of 100 to 300 m3 are used in rougher operation in different flotation industrial plants, in Chile and worldwide. However, in spite of the advances in fundamental research and the notable growing in equipment size, with more complete instrumentation systems, there are still a lack of reliable data for industrial flotation modeling and simulation to advance in better control systems design."

Jan 1, 2016

By A. D. McKay

Uranium exploration expenditure in Australia reached a record level of A$220.5 million in 2008, which has subsequently declined to A$185.2 million for the year ended 30 June 2009. Recent discoveries include: Ranger 3 Deeps east of Ranger open pit (Northern Territory), Pepegoona and Yadglin sandstone hosted deposits (South Australia), and Thunderball project (Northern Territory). Australia?s Reasonably Assured Resources recoverable at costs of <US$80/kg U at June 2009 are estimated to be 1,210,000 t U, 4% higher than the estimate for December 2008. The main additions were in the south eastern portion of the Olympic Dam orebody. The Olympic Dam Expansion is based on a large open pit and will increase output to an annual capacity of 19,000 t U3O8; 750,000 t copper; 800,000 ounces gold. The Four Mile in situ recovery project was approved in July 2009. An ion exchange facility is to be constructed at Four Mile and uranium-bearing resins will be transported to the Beverley plant to recover the uranium. Recent developments at Ranger mine, and Honeymoon, Oban and Yeelirrie projects are discussed.

Aug 1, 2010

By Fred G. Hewett

Cassiar Mine in northern British Columbia began development in 1952. The deposir is found on rhe west limb of rhe McDame Synclinorium in a Mississippian serpentinite body. The serpenltntte, one of the McDame l ntrusives, imrudes Sylvester Group . rocks, which comprise a Lare Devonian to Early M1ss1ss1pptan eugeosync/inal sequence of argillites, quarrzires and volcanics. The foorwall conracr berween Sylvester Group rocks and rhe serpenrinire is a marked zone of broken and incomperent argillite and graphitic schist. The less marked hang- 111gwall contacr 1s a band of indurated argillite. The JurassicCretaceous emplacemenr of the Cassiar Graniric Barholilh is responsible for mosr of the numerous )aims, faulrs and shear zones found in the serpentinite body. Faulting occurred borh before and after asbestos formation. Asbestos is mined from an open pit ar rhe rate of 4,535 ronnes daily. It passes from the pir along a rramline to the mill, where it is concen/rared into nine direcr milling grades. Packaged fibres travel ro over 40 counrries around rhe world for use in the texrile, cemenr and other industries.

Jan 1, 1984

By M. Lundström

The Outotec HydroCopper® process is a novel technology, developed and registered by Outotec Technology Oy, for leaching copper from chalcopyrite using cupric chloride solution. The leaching process is operated at atmospheric pressure in a stirred tank reactor, at temperatures near the boiling point of water and pH values between 1.5 and 2.5. During the leaching of chalcopyrite in cupric chloride solution, a reaction product layer forms on the mineral surface. In the present work, the formation and the composition of the reaction product layer was studied in an environment similar to that of the HydroCopper® process. The effect of the process parameters on the reaction product layer was investigated. Electrochemical measurements, including A.C. impedance spectroscopy and microscopic observations were carried out and an equivalent circuit was used to determine the surface parameters, such as the reaction product layer capacitance and the charge transfer resistance. The results suggest that, at low pH, a passivating sulfur-rich layer forms, whereas at high pH, a more porous iron-rich layer was detected. The values measured can give useful information for optimising the leaching parameters of the HydroCopper® process. Cu2007

Jan 1, 2007

By B. Zhu, W. E. Lee, N. Li

Al powder is used extensively as an antioxidant in carbon-containing bricks, but it cannot be used directly in water-based carbon-containing castables due to its hydration tendency. To overcome this problem, in this work, SiO2-PVA (polyvinyl alcohol) inorganic-organic hybrid coatings have been prepared via sol-gel processing, and used to coat Al powder. The hydration behaviour of uncoated and coated Al powders has been investigated in water at 60 or 100°C for 36h by examining phase and microstructural changes. While significant hydration is detected in uncoated Al powder, no obvious hydration is detected in coated Al powder, indicating that its hydration resistance has been greatly improved. Oxidation resistance of graphite coexisting with uncoated or coated Al powder was also investigated in air at 1250°C for 1.5h. The oxidation ratio of graphite coexisting with coated Al powder was similar to that of graphite coexisting with uncoated Al powder, indicating that both powders showed similar antioxidising behaviour. This, along with the much improved hydration resistance, makes the coated Al powder a potential antioxidant in carbon-containing castables systems.

Jan 1, 2004

By Y. M. Shneerson, E. E. Zhmarin, E. M. Vigdorchik

One of the Gipronickel Institute activities is research and development of customized leaching technologies. The work is performed in several steps. Leaching kinetics are studied on a lab-scale according to a special procedure. Experimental data are processed using mathematical models of batch and continuous processes. Reliability of kinetic data and preliminary calculations is verified experimentally in laboratory reactors of various capacities. If necessary, certain parameters of the mathematical model are adjusted after pilot plant tests in continuous mode ( 4-reactor train, each with 25 L capacity). The specified kinetic characteristics along with the mathematical model are used for further development of industrial leaching technology.

Jan 1, 2005

By F. H. Samuel, J. E. Gruzleski, S. Valtierra, H. W. Doty, F. J. Tavitas-Medrano

319-type cast Al-Si-Cu-Mg alloys are commercially important due to their popular use in automotive applications. Artificial aging heat treatments are commonly performed in these alloys to achieve precipitation hardening and, therefore, improve their mechanical properties. The present work was carried out to investigate the effect of conventional (at a constant temperature, as specified by the standard T6 heat treatment regime), and non-conventional multi-temperature and interrupted aging cycles on the hardness, tensile and impact properties of two 319-type alloys (with and without Sr+ Mg additions). The results show that certain multi-temperature aging cycles have a more favourable effect in improving some mechanical properties than conventional cycles.

Jan 1, 2006

By D. O. Tansey

This paper will describe the mechanisms involved in delay blasting and how they are applied with the use of D.S.B. It will examine the control of potential damage resulting from detonations, and show how good fragmentation and efficient recovery of this material blasted can be achieved.

Jan 1, 1979

By Z. Trojanová

The deformation behaviour of ternary magnesium alloys AJ (Mg-Al-Sr) and AX (Mg-Al-Ca) were investigated in tension as well as compression tests. The samples were deformed at temperatures between 20 and 300 °C and at an initial strain rate of the order 10-4 s 1. The flow stress decreases with increasing temperature. The macroscopic work hardening rate decreases with increasing flow stress and temperature. The stress and temperature dependence of the work hardening rate is a result of the hardening and softening processes. Stress relaxation experiments were performed in order to reveal features of the thermally activated dislocation motion. Internal and effective stress components of the applied stress were estimated. A decrease in the internal stress was observed at elevated temperatures, which indicates recovery process (-es). A more detailed analysis of the estimated values of the activation volume and activation energy helped to interpret the thermally activated processes during plastic deformation. It is concluded that the deformation behaviour of the alloys depends on the activity of non-basal slip that is strongly influenced by temperature.

Jan 1, 2007

By E. C. Keeley

THE property of Buffalo Ankerite Gold Mines, Limited, is in Delora township, Porcupine area, Ontario. The southwestern part of the property is ground formerly owned by Marbuan Gold Mines, Limited, which was acquired by Buffalo Ankerite in January, 1936. Until 1938, the Ankerite (or North) mine and the Marbuan (or South) mine continued as separate operations, each developed through a surface shaft and winze to the 1050 level and each having its own mill. This meant high hoisting costs, which, in 1936 and 1937, amounted to 36 cents per ton. In 1938, the underground workings of the two mines were connected on the 1050 level, and ore from both mines was hoisted at the main, or No. 2, shaft of the North mine, location of which is shown in Figure l. This shaft was discontinued at a depth of 1150 feet because, owing to the soft nature of the talc (serpentine) rock in which it was sunk, it had to be concreted throughout, and also because of its great distance--1,100 feet and 1,400 feet, respectively-from the North and South orebodies.

Jan 1, 1945

By Suzie Poulin, N. Geoffroy, G. P. Demopoulos

Most metallurgical industries generate toxic waste that must be treated prior to being released to the environment. However, in a lot of cases, the waste materials are poorly characterized or the analytical results are not well interpreted. These shortcomings often result in the development of inefficient industrial procedures, thus causing economic waste and difficulty meeting environmental regulations. Fortunately, a wide range of analytical techniques are available to guide researchers and engineers into making sound process development decisions. In this work, an industrial selenium and mercury removal process is used as an example to illustrate the application of X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) coupled with Energy-dispersive X-ray spectroscopy (EDX) and powder X-ray diffraction (PXRD) on solid waste. Furthermore, samples of analytical results are presented and interpreted and the modifications to the industrial process that resulted are explained. Finally, a brief description of the advantages and limitations of the aforementioned analytical techniques is given with an emphasis on industrial solid waste material.

Jan 1, 2011

By W. G. Hatch

Introduction Classified equipment originally installed in 1923 in the Britannia mill consisted of eighteen Model C Dorr Simplex classifiers, each in closed circuit with a pebble-mill. These machines were only three feet wide and of light construction, so that their raking capacities were necessarily limited, the maximum being about 20 tons per hour for each classifier. On conversion from pebble-mills to ball-mills, in 1924, attempts to increase circulating loads with higher rake speeds resulted only in overflowing a coarser product to the flotation cells. The elevator type of classifier was developed locally in 1935 and during that year two units, each having a sand carrying capacity of from 30 to 40 tons per hour, were installed. With such loads, a material increase in the grinding capacities of the ball-mills was noticed, and, after further development work on the elevator classifier, fifteen of the small Dorr classifiers were replaced by units of this type, capable of handling approximately 75 tons of sand per hour, with later alterations increasing this capacity to well over 100 tons per hour. In the meantime, the three remaining ball-mills had been placed in circuit with Dorr FX classifiers, one of which was six feet wide and the others five feet wide. Impartial and exhaustive tests conducted on the Dorr FX versus the elevator classifier showed the average results on these machines at Britannia to be substantially the same. A large amount of testing was carried on to determine the effect of circulating load on the output of the grinding units. This work indicated a rapid increase in the grinding rate as the ball-mill feed increased up to about 60 tons per hour, after which a relatively slow increase took place up to 100 tons per hour. No benefits were derived from higher circulating loads. A 300 to 500 per cent circulating load, depending on the nature of the ore treated, is considered to be within the economical range for the grinding of Britannia ores.

Jan 1, 1946

By Alvaro Diaz

Introduction, who is Teck Red Dog and Quebrada Blanca Mines Uniqueness of environment Arctic versus High Altitude Conditions Logistical challenges People and Stakeholders Conclusions

May 1, 2013

By Knud Sinding

Mining firms are widely criticised for their adverse impacts on the environment. At the same time many firms in the industry devote extensive resources, both financial and managerial, to the reduction or elimination such impacts. Very considerable improvements have been made, although these are sometimes overshadowed by a few high-profile accidents, such as the occasional collapse of a cyanide-containing tailings dam. In parallel, much effort is also directed at projecting a positive environmental image, as witnessed by extensive environmental reporting, both on paper and increasingly through web-platforms. Mining projects today almost invariably involve some form of environmental protection. In industrial countries regulations in this area are extremely stringent, as is enforcement. In less well developed countries, regulation and enforcement may be weaker, but firms are in many cases and for a number of reasons committing themselves to high levels of environmental protection, even if they might get away without doing so. Research in the area of environmental performance of mining firms has so far paid much attention to concepts such as sustainability indicators and the sustainability of individual firms. Given the still raging debates about the appropriate way to determine the degree to which any given firm is sustainable (Welford 1995) as well as the usefulness of what will in the final analysis be a value judgement, anyone on the sidelines of the debate will come back to the fundamental issue, how is knowledge that a particular firm has been judged ?sustainable? going to be made use of. This issue remains unresolved, which may explain the lack of progress in formulating a useful definition of a sustainable firm The question addressed in this paper is not so much about what firms are doing on the ground or in any particular case of environmental protection, but more in the subsequent use of these efforts - and by extension - on the overall direction of corporate environmental strategy. The fundamental problem facing all mining firms is that they cannot easily benefit from unilaterally reducing their environmental impact. The firm can of course avoid liability and keep a variety of stakeholders happy and hence experience lower costs of obtaining the [input] resources they need (in a broad sense, not just minerals), but this represents only part of the opportunities available form pursuing an environmental strategy (Reinhardt 2000). The other part, which may have an enormous potential, involves the concepts of competitor management and product differentiation. The logic of keeping stakeholders happy has been most forcefully argued by Pfeffer and Salanchick (1978) who link the behaviour of firms in all domains to their ability to obtain the resources they need, at a cost that is lower than it would otherwise be (Pfeffer & Salanccik 1978). Several varieties of strategy can be included under this heading, including cost reduction and risk management. The alternative logic is to convince customers that they want to pay more for minerals supplied by mining firm X or directly attributable to mine Y, or by making all mineral users pay more. These two strategies, which may be referred to as product differentiation and competitor management, respectively (Reinhardt 2000) are related to the demand side of mineral supply, whereas cost reduction and risk management are related to the supply side. Mining firms have not pursued the demand side very much, if at all. This is probably due to the extreme difficulty of moving mineral products, bulky and unglamorous as they are, away from their

May 1, 2003

By W. L. Ennis

Introduction This paper outlines the causes of underground fires at Noranda Mines and the precautionary measures taken to guard against such fi res. Shafts There are six shafts (Figures and lA) on the property, of which N os. 1 and 2 are abandoned. Nos. 3, 4, and 5 are the present working openings from surface and No 6 is an internal shaft. No. 3 is used primarily as a service shaft, while Nos.?1 and 5 are the main hoisting shafts. Orebodies The orebodies are of two distinct types. There are the massive sulphide bodies, and the areas of mineralized rhyolite containing gold values and a silica content high enough for fluxing purposes. The massive sulphide bodies contain chalcopyl&apos;ite, pyrite, pyrrhotite, and minor amounts of sphalerite and magnetite. The concentration of particular sulphides varies even within the same body. It is the areas high in pyrite, and to a lesser degree those, high in pyrrhotite, that are of particular interest.

Jan 1, 1950

By D. Lascelles, J. A. Finch, E. El-Ammouri

Flotation separation is expected to be related to the degree of dispersion of the pulp. For instance, highly aggregated systems may show reduced selectivity, reduced entrainment and increased flotation rate. In an attempt to test the impact of aggregation on flotation, we have taken advantage of the effect of Mg ions. Using combinations of Mg2+ and pH gave a wide variation in aggregation of several Cu-Zn ores (measured by settling rate) and corresponding flotation response was determined by batch tests. The trials were conducted on-site at Louvicourt and Agnico-Eagle. In a majority of cases a similar trend in aggregation and flotation selectivity (grade at given recovery) was observed. At Louvicourt, improved selectivity with increasing aggregation at pH 10.5 was found. At Agnico-Eagle, an analogous association between aggregation and selectivity was observed at pH 11.5. It is suggested that aggregation influences particle entrainment, the increased effective particle size reducing gangue recovery and hence improving selectivity.

Jan 1, 2004

By P. M. Shibley

"IntroductionMine drainage, surface. drainage and process liquors are the principal mine and mill effluents. The quantity and quality of these flows varies according to mineralogy, type and scale of mining, the process, tailing disposal, local ground conditions and climate.Typical contaminants remaining after solids sedimentation are colloidal or semi-colloidal particles, acids, alkalis, metals in solution, cyanides and thiosalts. Environmental regulations and guidelines have been issued in detail by the appropriate government agencies and will not be reviewed here. Revisions and additions are being made as our comprehension and abilities increase. Some contaminants of consequence have not been specifically regulated as practical treatment technology has not been identified. Thiosalts fall into that category as do the derivatives of the first stage of cyanide oxidation - cyanates.Most mining activities have present or foreseeable water treatment requirements. Because process economics can be adversely skewed by the environmental factor, the acknowledged objective of every operation must be to identify and anticipate those requirements.The evaluation and selection of water treatment techniques for mine-mill applications is complicated by the fact that most mine-mill effluents are high volume, dilute and chemically complex systems. Treatment processes applicable to most contaminants are: chemical or biological oxidation; neutralization and/or precipitation; liquid/solids separation. Other processes such as ion exchange, electro-deposition, foam fractionation, freeze crystallization and reverse osmosis offer the possibility of selective removal or concentration of contaminents. The latter tediniques, representing a slightly higher level of technology, are less suited to the large, low value flows usually encountered in the mine environment."

Jan 1, 1989