Search Documents

By Chri Langille, Dougal McCreath, Samantha Espley

"In 1993, trials of two innovative applications of liner support involving the replacement of bolts in the ground support system were undertaken at Inco mines. The first trial involved an evaluation of the effect of dynamic loading on mesh-reinforced boltless shotcrete in a sub-level cave mining area on 2400 level at Stobie Mine. The second trial involved an evaluation of the MIROC Mineguard spray-on liner as a replacement for bolts and screen support, or as a replacement for screen support alone, in a topsoil heading of a bulk, VRM (vertical retreat mining) stope on 3240 level at Lower Coleman Mine.In the Stobie Mine trial, an uppers retreat heading was supported using a two-pass system. First, shotcrete was applied 2 inches thick, followed by pinning of mesh screen to the back and walls. A second pass of another 2 inches of shotcrete was then performed. For recovery of the ore zone, a vertical slot was created using a Borepak blind boring machine. The uppers rings were blasted, one or two rings at a time, starting at the slot and retreating out of the heading. During blasting of the production rings, blast monitoring was used to record the ppvs (peak particle velocities). For a series of 5-ring blasts, the maximum ppvs were measured to be 0.4 m/s (16 in./s) with a maximum charge weight per delay of357 kg (800 Ib). Six 5-point convergence measurement stations were set up and after each blast the total rockmass convergence was measured using a tape extensometer. Although a maximum displacement of 100 mm (4 in.) was measured, the shotcrete still managed to provide some support junction. A support damage assessment was also done to try and relate blast vibration to effectiveness of the mesh reinforced shotcrete liner. This trial demonstrated the effect that blasting has, on a support system, and it also demonstrated the necessity of having the mesh reinforcement properly placed within the shotcrete."

Jan 1, 1995

By P. E. Weidmark

"PART I - Published PapersBallivy, G., and Dupuis, M., ""Laboratory testing for the design of grouted rock anchors""; Proc 6th Pan Am Conf Soil Mech Found Eng; Lima; 1:277-291; 1979.Ballivy, G., Ladanyi, B., and Gill, D., ""The effects of moisture content on the strength of fissured rocks""; Proc 1// 1ntnl Congr 1.A.E.G.; Madrid; //:2:7-16; 1978.Baumgartner, P., and Stimpson, B., ""Development of a tiltable base friction frame for kinematic studies of caving at various depths""; Int J Rock Mech Min Sci Geomech Abstr; 16:4:265-267; 1979.Bawden, W.F., and Roegiers, J.-c., ""Discussion and interpretation of the mathematics governing radial flow in a single horizontal rock fracture""; ISBN 07727-7002-6; Dept Civil Engng publication 79-11; Univ Toronto: 134p;1979.Chatterji, P.K., Smith, L.B., and Insley, A.E., ""Construction of Saline Creek Tunnel in Athabasca oil sand""; Can Geotech J; 16:1:90-107: 1979.Coates, D.F., and Gyenge, M., ""A case history of pit slope design""; Proc 4th ISRM Congr; Montreux, Switzerland; Sept 1979; 1:Theme IV:591-596; 1979.Crawford, A.M., and Curran, J.H., ""A dynamic direct shear machine for determining the time-dependent behaviour of rock joints"": Dept Civil Engng publication 79-08; Univ Toronto; 1979.Crawford, A.M., and Curran, J.H., ""A displacement discontinuity approach to modelling the creep behavior of rock and its discontinuities""; Dept Civil Engng publication 79-09; Univ Toronto; 1979.Crawford, A.M., and Curran, J.H., ""A higher-order displacement discontinuity element""; Dept Civil Engng publication 79-10; Univ Toronto; 1979.Cruden, D.M., ""A computer-based system for rock mass description""; Proc 1// Intnl Congr I.A.E.G.; Madrid; //:2:155-159; 1978.Cruikshank, D.J., and Curran, J.H., ""A.B.LE. approach to modelling of fluid flow in fractured rock masses""; Proc 7th Cdn Congr Appl Mech; May 1979; Sherbrooke, Que; 887-888; 1979."

Jan 1, 1980

By A. Haque

"This paper describes an improved formulation of an analytical shear strength model developed by Haque & Kodikara (2012) by incorporating the failure of regular concrete/rock joints subjected to CNS condition. Sokolovskii’s analytical solutions developed for failure stress of slopes have been found to be effective in this regard. The analytical models have been validated for predicting the shear behaviour of concrete/rock joints subjected to various CNS loading conditions. The model has been found to accurately predict the dilation, normal stress and shear stress behaviour for a regular triangular saw-tooth joint up to the peak shear stress. Moreover, the peak shear stresses of concrete-rock joints with asperity angles ranging from 5 to 27.5o compared reasonably well with the available laboratory test results.INTRODUCTIONA new shear strength model for elastic regular triangular concrete/rock joints loaded under Constant Normal Stiffness (CNS) boundary condition has been developed by Haque & Kodikara (2012). The salient feature of this model is its capability of accurately estimating the normal and shear stresses of joints with shear displacements under CNS condition by incorporating the elastic deformation of asperities. However, the shear strength model of Haque & Kodikara (2012) for the elastic asperities cannot be directly employed to predict the peak shear stress of a joint experiencing plasticity under applied loads. Therefore, the model inevitability requires articulation of an appropriate shear failure criterion simulating the boundary conditions of the loaded asperity to predict the peak shear stress and corresponding normal stress and dilation behaviour of concrete/rock joints. Sokolovskii (1960) developed a set of analytical solutions for failure stress of slopes comprising c-??soils, which can be exploited effectively to simulate the failure condition as encountered for loaded regular triangular concrete/rock joints (Seidel & Haberfield, 2002)."

Jan 1, 2015

By I. A. Cameron, F. Ham, R. Sriram

"Planned increases in electric furnace productivity and higher matte temperatures needed for the Sudbury Smelter's S02 Abatement Plan, require an improved matte tap hole. Since startup in 1978, the matte tap holes have been incrementally improved by the addition of copper cooling blocks around the refractory tap blocks. These improvements provided a tap block life of about 100 taps per campaign.In July 1993, a prototype matte taphole was installed in Number 2 Electric Furnace to develop the technology to increase tap hole service life. The design was based on a heat transfer model of the tapping process to determine candidate refractory materials and cooler arrangements. The prototype tap hole features increased copper cooling, high conductivity refractories and extensive instrumentation. Eight trial campaigns are reviewed outlining the performance of silicon carbide and graphite refractories and typical heat loads during tapping.IntroductionFalconbridge Limited operates two 36 MYA, 6 electrode submerged arc electric furnaces in Falconbridge, Ontario. The furnaces, commissioned in 1978, smelt a partially roasted nickel-copper calcine, to produce matte for converting and slag for discard. Additional details of the smelter are available in the literature(1-4).Each furnace was equipped with two matte tap holes located in the furnace end wall. Early in the campaign, matte tap holes were identified as a weak area in the furnace which could be improved. From 1981 to 1987, incremental improvements were made to the design by the addition of water cooled copper blocks. In 1993, a prototype matte tap hole was designed and installed in Number 2 electric furnace to develop the technology to increase tap hole service life. Improved service life is required to meet planned increases in electric fWl1ace productivity and the higher matte temperature needed for the smelter's S02 Abatement Plan.This paper reviews matte tap hole development since 1978; outlines the prototype matte tap hole design, refractory selection and installation; and details the performance of the prototype tap hole during the first eight campaigns."

Jan 1, 1995

Spatial information Critical to a project since it underpins: ?Discovery of mineral resources ?Orebodydefinition and technical assessment ?Mine design and planning ?Profitability and project value Data ?Single most import asset. ?Good interpretation of quality data underpins project growth and success. TEAMWORK

May 1, 2002

By George J. Cymerman

Since 1978, Syncrude Canada Ltd. has been expanding steadily its oil sand mining and processing capacity while reducing unit energy requirements. At the current rate of ~180 M tonne/year oil sand, the originally adopted Karl Clark?s 80°C version of the Hot Water process would require some 53 PJ (53 x 1015 Joule) heat. If this amount of heat were to be derived from burning natural gas it would cost $369 M/y (at $7/GJ). Fortunately, effective recovery of waste heat from the upgrading operations at the Mildred Lake site obviated the need for water heating with natural gas. The oil sand hydrotransport technology, first utilized commercially in the mid-nineties at Syncrude?s North Mine, reduced slurry temperature from ~80°C to ~50°C, cutting the unit heat requirement from 293 MJ/tonne to 183 MJ/t. However, in the new 100 Mt/year Aurora Mine even a 50°C process temperature would still require 18 PJ of heat energy per year. Only limited quantity of 65°C water could be imported from Mildred Lake site and some waste heat would be available from Gas Turbine Generators. A new, Low Energy Extraction (LEE) process was developed to minimize heat requirements by further reducing process temperatures to 25°C in the slurry pipeline and 35°C in the Primary Separation Vessels (PSV). Unfortunately, when applied to certain ore facies in Aurora, the LEE process yielded disappointing bitumen recoveries, necessitating an increase in slurry temperatures from 25°C to 35°C in the pipeline and from 35°C to 42°C in Primary Separation. In 2004, an Optimized Low Energy process (OLE) was developed and piloted at Syncrude Research using a 2000 kg/hour pilot plant. In the OLE process, most available heat is applied up-front to produce 45°C pipeline slurry at a density of 1.58 kg/l. Once the pipeline conditioning process is completed, the slurry is flooded with cold (10°C) water, resulting in PSV temperature of 34°C. The overall heat and water requirements are the same, or slightly lower, compared to those of the LEE process ? but without the penalty in bitumen recovery. Processing 100 Mt oil sand at 34°C (96 MJ/t), rather than at 50°C (183 MJ/t), will save $61 M/y (@ $7/GJ) and reduce green house gas emissions by ~47 %. The OLE process is currently being implemented at the Syncrude Aurora Mine.

May 1, 2006

By H. J. Meyer

"A hydrostatic elevation difference meter has been developed for use in measuring elevations along gravity traverses. Elevations of stations 100 feet apart can be obtained at a rate of 1/2 mile per hour and to an accuracy better than 1/3 foot. This can be done along traverses which have not been cut and chained. The instrument is durable, lightweight and constructed of materials which will withstand any temperature encountered in field work.It is believed that this device will more than double the rate at which gravity surveys over mining prospects can be carried out."

Jan 1, 1972

By M. Specht, D. Pörzgen, W. Lorenz, A. /. Buhr, R. P. Racher

The introduction of the near net-shape casting process at CORUS Staal IJmuiden in January 2000 required changes of secondary metallurgy processes including a development towards more aggressive slag compositions in the steel ladle. Therefore the steel ladle lining has been changed from fired andalusite bricks to magnesia-carbon bricks and, most recently, to fired spinel bricks to withstand the severe slag conditions. In comparison to the andalusite bricks the new steel ladle linings have a higher thermal conductivity. This requires the capability to keep the lining warm by ladle preheaters to sustain the overall thermal stability of the steel ladle in case of interruptions during hot cycling of the ladles.

Jan 1, 2004

By K. Nagy

To support the implementation of its integrated SHEQ Policy, Cameco has undertaken an environmental leadership initiative with the goal of moving beyond regulatory compliance and significantly reducing environmental impacts in five key areas: air emissions, treated water quality and quantity, energy use and greenhouse gas emissions, and waste generation. To ensure environmental leadership becomes routine business practice, it was necessary to integrate the initiative into Cameco?s programs and management systems at the corporate and operational levels. Operations based environmental leadership strategies and action plans have since been developed, as well as a corporate reporting system to monitor Cameco?s environmental performance.

Aug 1, 2010

By D. W. Davis, P. Landais, L. J. Robb

Nodules of carbonaceous matter have been observed in several Archaean peraluminous granites adjoining the gold- and uranium-bearing Witwatersrand Basin. These nodules, which resemble solid bitumen, usually replace uraninite or uranothorite and are paragenetically late. They show many similarities to kerogen seams and nodules associated with the conglomerate horizons in the Witwatersrand Basin, including composition, maturation, intimate association with uraninite, and a late paragenesis. U-Pb isotope ratios for granite-hosted and Witwatersrand kerogens define a single, albeit somewhat diffuse, Ph-loss discordia suggesting an upper intercept age of circa 2300 Ma. Carbon isotope analysis indicates lighter Ol3C values for the granite-hosted nodules than for the sediment-hosted kerogen seams. Raman spectroscopy indicates that granite-hosted kerogen is more highly ordered than Witwatersrand seam kerogen. A model is presented which links the granitoidand sediment-hosted organic matter to an event of oil generation in the Witwatersrand Basin circa 2300 Ma ago. Light hydrocarbons migrated through the sediments and into underlying/adjacent granitic rocks, undergoing polymerization and accumulation in response to radiation accompanying the presence of high-uranium phases.

Jan 1, 1994

By K. van Netten, T. P. Ernst

"Froth flotation has been used successfully for about a century in the beneficiation of both coal and mineral particles. With the on-going trend towards lower feed grades, however, there is a need to transform this technology in ways that can deliver ultrafast separations, with strong selectivity, and recovery, covering a broader size range. It should be recognised that the hydrophobic effect, with its highly selective and long-range interactions, will most likely underpin any new technology. We identified the separation of the concentrate from the tailings as the rate determining step of conventional flotation technology. This limitation was then addressed by developing a novel flotation technology, insuring the formation of a concentrate that could be separated more rapidly from the tailings. We introduced a novel binder medium, a highly concentrated water in oil emulsion, to act as the focal point for hydrophobic adhesion, effectively replacing the air bubbles used in conventional flotation. The hydrophobic particles adhere to and become embedded within the binder, forming saturated agglomerates that float upwards. Moreover, by forming these large and resilient agglomerates, the product can be quickly dewatered over a screen and separated almost immediately from the tailings. Remarkably, this new binder permits residence times in the order of a few seconds under batch conditions. This paper examines the performance of the technology as a function of the oil wt% added to the slurry. The paper also examines the performance of the technology as a function of the particle size, showing a decline as the particle size exceeds 0.50 mm.INTRODUCTIONFroth flotation involves the collision and adhesion of hydrophobic particles to rising air bubbles, the carrying of those particles from the bubbly-pulp zone into a froth zone, and subsequent drainage and migration of the pulp to achieve the final concentrate (Wills, 2006). Within a Jameson Cell the feed slurry and air bubbles are brought into intense contact within the active area of the downcomer, achieving rapid kinetics of hydrophobic particle adhesion to the air bubbles (Harbort et al., 1994). However, once the bubble laden product and tailings emerge from the downcomer there is the need for separation of the concentrate from the tailings, an inherently slower process. In other devices such as mechanical cells the initial kinetics of particle adhesion are far slower, relying on the turbulent eddies throughout the cell, while in a column the kinetics rely upon an even slower process of bubble interception with suspended and settling particles (Gorain, 2007). However, in all cases the driving force for segregating the bubbles from the tailings, and the drainage of the froth are inherently the same. We do note, however, recent advances by Galvin and co-workers in achieving so-called Fast Flotation, utilizing a system of inclined channels to dramatically increase the segregation rate of bubbles from the tailings, permitting much higher gas and feed fluxes to be applied, achieving up to a ten-fold throughput advantage (Dickinson et al., 2014). Any further improvement within the existing flotation paradigm would require the introduction of centrifugal forces, but this would also require the formation of much finer bubbles than is typically used given the tendency of relatively large bubbles to reach a limiting slip velocity due to deformations and increased drag. Across all flotation devices we argue the rate determining step remains the segregation of the bubbles from the tailings."

Jan 1, 2016

By Douglas W. Reeve, Hoc Nghia Tran, David Barham

"In kraft pulp mills, the spent pulping liquor is concentrated and used as fuel in the recovery boiler. Extensive deposits are formed in the upper section of the boiler due to the very high ash content of the fuel and the volatite nature of the ash. Deposits are composed of Na2S04, Na2C03 NaCI, some potassium salts and reduced sulphur compounds. Chloride and potassium salts are enriched in the deposits compared to the smelt due to their greater volatility.Severe corrosion of the superheater tubes in a recovery boiler has been traced to three factors: a non-uniform temperature profile in the flue gas, relatively high operating steam temperatures and high chIoride and potassium concentrations in the fireside deposits.The role of chIoride and potassium in superheater corrosion has been explained by increased Iiquid phase in deposits. Together with corrosion studies, this information has shown that kraft recovery boiler superheater corrosion due to the chloride and potassium enriched deposits can be avoided by proper boiler operation and by judicious superheater and furnace design.IntroductionThis investigation of recovery boiler superheater corrosion was initiated by the discovery of severe corrosion of the final stage superheater in a Canadian closed cycle kraft pulp mill(1,2). Metal wastage leading to tube failure was believed to be due to three major causes : the relatively high operating steam temperatures, the uneven distribution of flue gas temperature across the boiler which created a "" hot spot"" and the high chloride and potassium concentrations in the superheater fire side deposit. The mill responded to the problem by i) lowering the superheater steam temperature from 475°C to 380°C, ii) minimizing the chloride content in the spent pulping liquor, by controlling the NaCI input with recovered bleach plant effluent, and iii) changing metallurgy of a portion of the bottom section of the final stage superheater platens from ferritic steel T-22 (2.25% Cr, 1% Mo) to austenitic steel Incoloy 800H (21% Cr, 32% Ni, 46% Fe, 1.5% Mn, 1% Si, 0.6% Al) (Fig. 1). Details of the superheater corrosion experienced in the closed cycle mil! have been reported in previous papers(l ·2,) ."

Jan 1, 1984

By C. E. Cartwright

That the construction of the Pacific Great Eastern railway has not been accompanied by an immediate and great development of traffic is not due to lack of natural resources in the district traversed, but to conditions that have delayed their development. Prior to the commencement of construction of the railway there was no inducement to prospect for any other mineral than gold, on account of lack of transportation. The war began soon after the commencement of construction; diverting practically all capital that might have been available for opening up the country; and since the war, capital has continued shy of new investments. If the war had not occurred it is probable that prospecting and development would have been carried out concurrently with the railway construction. Moreover, much of the district is covered deeply with drift, marine and alluvial deposits, rendering prospecting for lode mines a more expensive and slower proceeding than can generally be undertaken by the ordinary prospector, without capital. On the other hand, the presence of large porphyry dykes, granitic intrusions, and the finding of rich float in places are indications that rich miIY.ral deposits probably exist in several localities in the Lillooet district, in the Cariboo proper, and also nearer the coast. Two or three mines producing the tonnage of the? Britannia would materially alter the earnings of the railway and pay interest on the bonds. There are, however, other possibilities, in addition to large metaliferous mines, in the non-metallic minerals of the district.

Jan 1, 1925

By M. Mahfoud

The effect of grain refinement on the tensile and fatigue crack propagation behavior of sand cast magnesium alloy AM60B has been investigated in the present study, C2Cl6 in the amount of 0,3% was used to grain refine the melt, The fracture toughness tests were conducted in laboratory air at room temperature (25°C) using a sine-wave cyclic frequency of 20Hz and a load ratio of R = 0,1, The response in the Paris's regime and the critical stress range were determined, Preliminary findings have shown that C2Cl6 has a significant effect on both the tensile properties and fatigue crack propagation of the alloy tested, Grain refinement increased both the yield and ultimate tensile strength by more than 46%, and decreased the crack growth rate from 2,7 to 1,4 MPa Vm , However, the grain size seems to have a smaller effect on threshold stress intensity factor range. The fracture surfaces of specimens were examined optically and under the scanning electron microscope (SEM) to determine the relationship between grain size and fatigue properties.

Jan 1, 2005

By Wataru Inagaki, Kozo Kawano, Tetsuya Ando

Cu–Ni–P alloys are the typical precipitation-hardening material. Thus, Cu–Ni–P alloys is expected to apply alternative materials for heat-exchanger tubes. Therefore, it was investigated that the effect of the heat-treatment simulated brazing on mechanical properties of Cu–Ni–P alloy in this study. The hardness of specimen as heat-treatment simulated brazing after solution heat treated (sht) was shown approximately 105 HV. The peak hardness and tensile strength of the specimen as performed aged at 498 K for 43.2 ks following the heat-treatment simulated brazing achieved at approximately 140 HV and 260 MPa, respectively. From these results, it is expected the application to higher-strength tube for heat-exchanger after brazing in a furnace. INTRODUCTION Copper prices have increased dramatically with high in recent years. At the same time, manufacturing industries are required to reduce the environment load by reducing the wall thickness of the copper tubes used in heat exchangers. High-strength copper alloys are developed for reducing the wall thickness, while achieving high strength, of the copper tubes. Moreover, excellent workability and corrosive durability are also required by these copper tubes. Furthermore, the brazing, which are carried out at about 1050 K during the assembly process of heat exchangers, leads to grain growth and re-solving of additive elements. Nomura et al. achieved a tensile strength and Vickers hardness of approximately 260 MPa and 110 HV, respectively, after aging at 723 K for approximately 36 ks. Tamagawa et al. studied that the strength of Cu–Ni–P alloy rapidly increased at about 125 HV during the cooling process after the heat brazing due to the Ni2P precipitates sized 5–10 nm. Furthermore, Inagaki et al. achieved a Vickers hardness of approximately 130 HV by aging at 498 K for 10.8 ks. In the present study, we focused on the lowest aging temperature of 498 K in the previous study, and investigating the effect of heat-treatment simulated brazing on the mechanical properties of the Cu–0.93 mass%Ni–0.24 mass%P alloy.

Jan 1, 2019

By J. H. Rickard, D. H. Watkinson

"Abstract - Detailed petrographic and quantitative (electron microprobe, SEM-EDS) mineralchemical analyses of sulfide ore from the 100 orebody at the Copper Cliff North mine, Copper Cliff, Ontario, reveal numerous stages of ore development. Sharp contacts between weakly mineralized quartz diorite and blebby to massive sulfides indicate multiple intrusive events within the Copper Cliff offset dike. A spatial association of sulfides and hydrous minerals, such as amphibole, biotite, chlorite and epidote, suggests that most primary ore has been affected by later hydrothermal fluids. Sulfides are often enclosed or bordered by these secondary silicate phases. The ore consists primarily of pyrrhotite, pentlandite, chalcopyrite, with trace michenerite, cobaltite/gersdorffite, irarsite, hessite, tsumoite, and bismuth tellurides.Geological and petrological comparison of the 100 orebody and the adjacent 900 and 890 orebodies has revealed distinct similarities in ore distribution. Data show that the 100 orebody is depleted in platinum-group elements (PGE) relative to the 900 orebody. Platinum-group elements from the 100 orebody may have been hydrothermally remobilized and partly emplaced in the 900 orebody, in adjacent veins, or in magmatic breccia. Analysis of Cu, Ni, and PGE assay data of ore samples has characterized their distribution among the eight different ore textures in the orebody. There is a strong association between Pt and interstitial sulfide, and to a lesser extent massive sulfide, but little correlation between chalcopyrite-rich ore and PGE in the 100 orebody, unlike many other deposits in the Sudbury region."

Jan 1, 2001

By Y. H. Hatzor, D. Bakun Mazor

"A new model for thermally-induced block displacement in discontinuous rock slopes is being explored inside a Controlled Climate Laboratory (CCL). The model is based on a hypothesized wedging mechanism that takes place inside the filled tension crack of a discrete block that rests on an inclined plane. Irreversible block sliding is assumed to develop in response to climatic thermal fluctuations and consequent contraction and expansion of the sliding block material. While an analytical expression for this model is already available, we are exploring the possibility of obtaining such a permanent, thermallyinduced, rock block displacement, under fully controlled conditions in the laboratory, to enable effective analysis of the sensitivity of the mechanism to geometry, mechanical properties, and temperature fluctuations.A large scale (approximately 0.5 m3 in volume) model consisting of four blocks has been installed in the CCL. The CCL permits accurate control of atmospheric temperature (?0.5 °C) from 6 °C to 45 °C. Harmonic temperature function is planned in advance and is controlled by a computer program throughout the experiment process. The minimum length of the temperature cyclic period for thermally-induced block displacement is calculated here based on the existing analytical model.Due to the fact that this experiment is still in progress, preliminary results will be available in the next few months. The obtained results may explain sudden triggering of rock slope failures that are not correlated with common failure triggers such as seismic activities, pore pressure build-up, or freezing and thawing of water inside rock joints."

Jan 1, 2015

By Elizabeth Edwards, Radhakrishnan Mahadevan, Vladimiros G. Papangelakis, Srinath Garg, Kurtis Judd

Mineralogical characterization of the tailings showed the deportment of Ni to be similar in the Vale and Glencore tailings, with 60% of the total Ni locked in pyrrhotite, and the balance 40% associated with pentlandite. The overall Ni dissolution was correlated with the individual dissolution extents of pyrrhotite and pentlandite as functions of four leaching regimes: ‘anoxic acid’ (with and without pH control), ‘oxic acid’ (oxygen sparging), ‘oxic acid’ (air sparging), and ‘oxic ferric’ (air sparging). The results showed that the maximum Ni dissolution was obtained during the pH controlled oxic acid leach with oxygen sparging at pH 1.5, while the anoxic acid leach at pH 1.5 resulted in minimum Ni dissolution (10–15%) from pyrrhotite. An overall Ni mass balance showed that pyrrhotite and pentlandite dissolve simultaneously in the presence of Fe(III) and oxygen, in contrast to the preferential dissolution of pyrrhotite in the absence of Fe(III). Sulphur mass balances revealed that the yield of elemental sulphur is maximized (65%) during the oxic Fe(III) leach at pH 0.6. Furthermore, the kinetics of Ni leaching and elemental sulphur formation from pyrrhotite tailings leached with ferric sulphate between 55–80°C was investigated at constant oxidation-reduction potential. Elemental sulphur yield increased with increasing temperature, but no observable trend could be linked to ferric or ferrous ion concentration.

Jan 1, 2017

By Yongfeng Jia, Shaofeng Wang, Danni Zhang

Arsenic in mineral processing solutions and effluents is commonly removed and immobilized via iron(III)-arsenatecoprecipitation. The effect of re-crystallization of 2-line ferrihydrite on the long-term stability of iron(III)-arsenate coprecipitate is still not fully understood. This work investigated the redistribution of arsenic and iron during 2-line ferrihydrite transformation at different pHs and temperatures over time. X-ray diffraction (XRD), transmission electron microscopy (TEM) and chemical extraction were employed to characterize the crystallinity of the iron oxyhydroxides. Results showed that the amount of arsenic released into solution during aging increased significantly with increasing media pH.

Jan 1, 2014

By Z. D. Hora

Air hough diatomite is known in many parrs of British Columbia, deposirs of mineable size have only been found in the area between Kam/oops and Quesnel in the sourh-cenrral parr of rhe province. Ar Quesnel, commercial producrion has continued since 1950 from diatomite lenses up ro 35m rhick. OCCURRENCES of diatomite are reported from many parts of British Columbia, but deposits of mineable size are known only from the area between Kamloops and Quesnel. Only Quesnel deposits have yet reached the production stage. Commercial production dates back to 1950, and up until 1979 approximately 22,700 tonnes of diatomite had been produced. Most extracted diatomite was processed until 1980 by Crownite Industrial Minerals Limited in Quesnel to produce an oil absorbent and animal bedding. Smaller shipments are used to make insulating bricks on the lower mainland. Deposits near Quesnel extend 40 km along the western bank of the Fraser River from Quesnel to Alexandria; most production has come from Lots o. 6132 and 906. Di atomite is present as discontinuous lenses up to 35 m thick. Diatomite beds Industrial Minerals in Canada are of Upper Miocene age and are overlain by plateau basalts. Diatomite consists almost exclusively of Melosira granulara diatoms that are usually very small and mixed with variable amounts of clay, ilt and volcanic ash. In recent years, extensive beds of diatomite were identified near the confluence of the Chilcotin and Fraser rivers. Diatomite in this locale is a part o f the Upper Miocene to Pliocene Chilcotin Group of sedimentary rocks that are overlain by olivine basalt and related luffs. A deposit near Red Lake is situated 50 km northwest of Kamloops. Diatomite beds occur in the Tranquille Series of Eocene age and are similar in composition to those in the Quesnel area. The Red Lake deposit is abo ut 4 m thick but its areal extent is only a few tens of hectares.

Jan 1, 1984