Search Documents

By T. Guan, G. Fu, X. Zhou, L. Deng

"Currently, tailings water is required to be recycled in minerals processing plants. When the flotation tailings water of complex copper-sulfur-tungsten polymetallic ore is reused to the flotation of copper-sulfur ore, a portion of tungsten would be lost in copper concentrate or sulfur concentrate due to the addition of the collectors used for oxidized ore which are also effective for the sulfide minerals in the process of tungsten flotation. At the same time, the technical index of copper concentrate and sulfur concentrate would be seriously affected by tailings water. Our experimental researches of many years show that the copper concentrate with a grade of 18.36% Cu at a recovery of 76.67% is obtained for the raw ore containing 0.60% Cu, 18.99% S, 0.16% WO3 in small locked cycle test using recycled water, through simple pretreatment of the tailings water from tungsten flotation and adding special regulator CW and new tungsten collector TM. The result is close to the performance without using tailings water. And, in the continuous pilot experiment which was continuously conducted for 4 days with the same technology, the following results was obtained: the copper concentrate with a grade of 21.74% Cu, the recovery was 71.55%; the sulfur concentrate with a grade of 45.16% S, the recovery was 80.10%; the tungsten concentrate with a grade of 42.63% WO3, the recovery was 54.62% relative to raw ore (the recovery relative to scheelite was 76.47%). The throughput of the continuous pilot experiment is 1.0~1.2 t/d, and the raw ore contains 0.56% Cu, 18.80% S, 0.14% WO3 on average.INTRODUCTIONMining industry is one of the most important developing fields, it supplies raw materials for industrial production as well as discharges much waste water. Tailings water is the main source of beneficiation waste water, it would result in severe environmental pollution if discharged directly. Generally, the tailings water would bring undesirable effect on flotation index after simple pretreatment by lime (Kalin, Fyson, & Wheeler, 2006). On the other hand, the treatment of tailings water through ion-exchange (Cui & Liu, 2015) before recycling is of high cost. Generally, in the flotation of Cu-S-W polymetallic ore, when the tailings water from tungsten flotation is treated simply by lime and recycled to the flotation of sulfide minerals, the flotation index of sulfide minerals decreases, and a portion of oxide mineral would be lost in the sulfide concentrate. As a result, the recycle rate of this kind of tailings water is relatively low, some of the tailings water is discharged after simple treatment and then environmental pollution is caused subsequently. One of the effective ways to improve beneficiation performance and increase the recycle rate of tailings water is to conduct research on developing recycle technology for flotation tailings water of complex copper-sulfur-tungsten polymetallic ore."

Jan 1, 2016

By I. Colquhoun

Current practice tends towards "integrity as an afterthought". That is, integrity is treated as an isolated aspect of operations and maintenance. In fact, this works quite well. But it would work so much better and with less uncertainty if integrity management measures were introduced at the design phase and addressed the entire life-cycle of the pipeline asset. The talk will address the measures and metrics that can be implemented on a new pipeline during design to optimize integrity and deliver a comprehensive operating manual and integrity management program for the pipeline system. This deliverable should describe the risks to be assessed and monitored, and the actions to be taken to control these risk adequately. Properly executed, integrity by design will provide a good working estimate of the life-cycle integrity management costs and maximize system reliability.

Jan 1, 2005

By M. Drozd, A. Ibrado, P. Butcher

While effective in treating refractory sulfide ores, pressure oxidation leaves carbonaceous matter unscathed and able to adsorb gold from cyanide solutions. Barrick Goldstrike's strategy to mitigate this problem is to minimize contact between dissolved gold and native carbon in advance of the carbon-in-leach (CIL) process. Measures currently in use include limiting carbonaceous matter in the plant feed by meticulous blending of ore, controlling the degree of oxidation in the autoclaves and blinding native carbon surfaces with lauryl sulfate. The presence of residual cyanide and thiocyanate in the process water remains to be a cause of premature gold dissolution and loss of gold by adsorption on carbonaceous matter. This cyanide is introduced by water that is recycled from the tailing pond. Of several treatment options considered, oxidation by peroxymonosulfuric acid, also known as Caro's acid, is deemed to be the most effective. Laboratory and pilot plant tests show that Caro's acid can oxidize free cyanide, weak¬acid-dissociable (WAD) cyanide and thiocyanate, resulting in significant improvements in gold recovery downstream. The process requires Caro's acid at 125 % of the stoichiometric requirement and pH in the range of 9.5 to 10 to accomplish the desired destruction in about twenty minutes. A cyanide destruction plant is currently being designed and construction should be completed by the end of 2005.

Jan 1, 2005

By H. P. Whaley

This paper introduces Wabush Mines, including its ownership, physical assets, capacity, goals and achievements. It is to be followed by four papers which will present the detailed story. Wabush Mines, the largest supplier of iron ore to the Canadian steel industry, was brought into production in 1965. The ore is mined and concentrated in Wabush, Labrador, Newfoundland and pelletized at Pte. Noire, Quebec. Annual capacity is over 6,000,000 tons of high-grade iron ore pellets.

Jan 1, 1969

By R H. Hallam

The Mattagami mining district encompasses a favour-?able belt of folded Keewatin-type rocks, with intercalated sediments and intrusives of late Keewatin age. This environment has been subjected to periods of basic and acidic intrusion. The orebodies lie within the fold structure and are associated with faulting and shearing of considerable magnitude. The No. 1 orebody contains 60 to 70 per cent massive sulphides. The minerals, in their order of abundance, are generally: pyrite, sphalerite, pyrrhotite, magnetite and chalcopyrite. It is evident that the broad geological structure of the district is amenable to ore deposition. There are two ? prominent linear expressions which comprise this broad structure. Both strike directions lie at the edge of, or are related to, a complex gabbro-anorthosite-peridotite zone. The fact that eleven of the ore zones discovered to date coincide with the broad structure indicates its over-all importance. It is estimated that the production from Mattagami Lake Mines will be in the range of 600 to 700 tons of zinc concentrate and 70 tons of copper concentrate per day.

Jan 1, 1964

By M. Kowalczyk

The successful application of color sorting machines has established sensor-based sorting in the mineral industry in recent years and is considered today as a significant innovation in processing technology. However, we are only at the beginning of the (market) introduction. New sensor systems have been developed, which exploit material properties such as electrical conductivity, magnetization, molecular structure, thermal conductivity etc. This opens up new exciting pre-concentration and upgrading possibilities for many applications such as nickel, gold, copper and other ores as well as for industrial minerals, diamonds and other gemstones.

Jan 1, 2009

By J. H. Schloen

"One of the most important phases in Canada's relatively rapid development of its metal mining and refining industries was launched in 1928 when the directors of Noranda Mines Limited decided to establish an electrolytic copper refinery ""somewhere in Eastern Canada”. Noranda's president, J.Y. Murdoch, had already evolved the company's ""mine to market"" policy and was determined to prove the economic feasibility of refining Noranda copper in Canada. The time appeared to be ripe as buoyant business conditions continued into 1929. In addition, proven ore reserves at the Horne Mine in northwest Quebec had virtually tripled and the price of copper had reached a healthy 15 cents per pound. Letters Patent incorporating the company bearing the date February 6, 1929 had been granted by the Secretary of State in accordance with an application that specified a capital structure of $2 million divided into 20 000 shares with a value of $100 each. Noranda assumed 70% of the original investment in the proposed refinery, while the Nicholas Copper Company of New York (which later became Phelps Dodge Corporation) and British Metal Corporation Ltd. of London, England, each were responsible for 15%. Nicholas Copper Company agreed to supply the design and to supervise the construction of the refinery and British Metal Corporation would act as sales agent and market the refinery's products."

Jan 1, 1999

By G. C. Bateman

Canada is a very large country with a small population which is growing very slowly. We have great natural resources, but with our limited population we are continually looking afield for new capital to develop these resources. Our mining areas are among the most important fields offering opportunities for new capital and because of the wide-spread appeal which mining makes this industry commands a great deal of attention. While we are glad to see new capital from any source, we welcome it particularly from Great Britain, for, although we offer equal opportunities to the nationals of any country we would be glad to see the development of our natural resources financed as far as possible within the Empire. However, when we invite ne capital we must accept certain responsibilities, and while we have opportunities to offer, we should ask ourselves how these opportunities are taken advantage of and what sort of treatment the foreign investor receives.

Jan 1, 1925

By F. J. Munn

"Since 1976, Cardinal River Coal s Ltd. has completed mining in eight pits. In each of these pits, at least one wall has failed, none by design, although not totally unexpected, yet there was no loss of production nor risk to personnel or equipment. Cardinal River Coals Ltd. has been successful in implementing a program to cope with failures and now feels justified in adopting more optimistic design parameters.The wall control program at Cardinal River Coals Ltd. is based on the premise that the walls are going to fail, monitoring is to confirm when. The program consists of monitoring slope movements and piezometric levels as well as structural mapping and visual inspections. In case of excessive movement, the frequency and intensity of the monitoring is increased. If a failure is impending, suitable remedial action is undertaken such as cutting down the crest, building up the toe, depressurization of the wall, artificial support, or a combination of the above. If remedial action is not possible, monitoring permits operations to continue up to near the time of failure.At the design stage, the emphasis is on identifying the potential failure mechanisms and the con sequences of failure. Once the potential failure mechanisms are identified, a monitoring system can usually be employed to give sufficient response time, and providing the consequence of failure is not severe and/ or remedial action can be taken to arrest the movements, then it is practical to mine pit slope s which have a higher probability of failure."

Jan 1, 1985

By Fathi Habashi

Extraction by organic solvents is a chemical process in which metal species in the aqueous phase react with an organic reagent to form an organometallic com- plex, thus, the metal species leave the aqueous phase and enter the organic phase from which it can be stripped back in the aqueous phase to obtain a pure and a concentrated solution. The metal in the organic phase is not bound to carbon atoms as in organometallic compounds but to oxygen, nitrogen, sulphur, or hydrogen by a co-ordination (dative) bond (Habashi, 1999).Solvent extraction was used for the first time in hydrometallurgy in connec- tion with the special and urgent materials requirements of nuclear energy during World War II. A plant was constructed in the United States for the preparation of high-purity uranyl nitrate solution. In this plant, the yellow cake (a high-grade sodium or ammonium uranate) was dis- solved in HNO,, and uranium was selec- tively extracted by ether then stripped by water to give a concentrated solution of pure uranyl nitrate. This was gradually followed by developing methods for other high-priced metals such as plutonium, thorium, niobium, tantalum, zirconium, hafnium, boron, beryllium, and molybde num. The second step took place in the 1960s when solvent extraction was applied for the first time to extract a rela- tively cheap metal-copper. At present, solvent extraction technology is wide- spread, well accepted, and highly efficient. Solvent extraction had its origin in the discovery, by Christian Friedrich Bucholz (1770-1818) in 1805, that uranyl

Sep 1, 1999

By I. Stanoev, V. S. Stoilov, I. Gradinarov, E. D. Visariev, I. A. Bonchev, Aurubis Bulgaria

"Aurubis is the leading integrated copper group and the world’s largest copper recycler. In Copper smelter Aurubis Bulgaria (Pirdop), the residual copper in the slags from Flash furnace and Converters is recovered by flotation. The slag processing comprises: pit cooling, crushing, two stages grinding (autogenous and ball) and flotation. The copper concentrate is thickened and then is filtrated by vacuum disk filter. The thickener overflow is sent to settler for additional clarification. A resent throughput increase resulted in higher solid content in the thickener overflow due to insufficient thickener area. Different scenarios to overcome the issue were evaluated (new thickener, reagents and reconstruction). An increase of the thickening area by installation of lamella modules was chosen as the most promising option. Three lamella modules (1 m3 each) were installed in conventional thickener for the test. Number of sampling campaigns was done to evaluate the effect on solid content in overflow. Parameters of the dewatering cycle were collected during sampling campaign. The products grain size distribution was defined - thickener feed, thickener overflow with and without lamella. The thickener overflow with lamella modules has 2.12 g/L less solid content. The decrease was 71.8%. According to the tests results, the whole conventional thickener was reconstructed with lamella modules. The thickener area was increased by more than 400 m2.INTRODUCTIONIn Copper smelter Aurubis Bulgaria, the copper in slag from the Flash furnace and the Converters is recovered by flotation. The scheme of slag processing is crushing, two stage grinding (autogenous and ball) and flotation. Till 2010 the grinding cycle in the plant was in two stages: the first stage was AG Mill 70×23 working with a classifier and the second stage was ball mill 3.6/5.5 working with a hydrocyclone. In 2010 a new AG Mill 65×78 with hydrocyclone was put in operation in order to increase throughput of the plant. The second stage of the grinding cycle was not changed."

Jan 1, 2016

By Thomas C. Poulter

Abstract The Poulter seismic method of geophysical exploration is an attempt to obtain an increased efficiency in the conversion of the energy of an m~pl06ion into useful energy which has directive properties and which contains a minimum of random frequency and random phase relations. Very little effort has been made in the past to simplify OT even control the uniformity of the seismic energy being introduced into the ground. The Poulter seismic method is also an attempt to improve the signal-to-noise ratio not merely by trying to complete the impartial filtering done by the earth on ,the continuous spectrum of primarily high-frequency energy radiated from a shot point but by applying a frequency control at the point of origin of the seismic wave. The energy from a shot-hole charge is peaked in a frequency which is much higher than will be transmitted through the ground, and its absorption introduces background interference. Only 10 to 20 per cent of the seismic energy of a shot-hole charge .is directed downward in a 90-degree vertical cone, whereas, from a pattern of charges detonated above the surface of the ground, 85 per cent of the seismic energy is included in a 90-degree cone and in some cases it is even confined to as small as a 30-degree cone. This greatly reduces the horizontally distributed energy, thereby producing a marked improvement in the signal-to-noise ratio. The frequency of the signal energy may be peaked in a rather narrow range by the proper application of two or more impulses upon the surface of the ground controlled as to direction, magnitude, and timing. These impulses may be controlled by the reflection shock wave technique, the pressure pulse technique, and the sequence firing technique, using the primary controls as outlined. The information obtained from the study of directivity of seismic energy in a high velocity, uniform material such as the ice on Taku glacier, in the Juneau ice field in Alaska, has been of great assistance in the application of the method to oilfield and mining problems.

Jan 1, 1950

By N. D. Wineinger, J. Jodouin

"An Independent Electricity System Operator Industrial Accelerator Program (IESO IAP) case study was completed for a mine in Ontario, Canada by SRK Consulting, Inc. The purpose of the study was to analyze the ventilation system to determine whether and which system improvements could reduce the overall electrical power demand of the mine. Financial incentives are offered by the IESO IAP grant program to help cover the capital costs of these improvements. This study included the completion of a full mine ventilation survey as well as measurement of a full suite of electrical parameters of the surface and underground ventilation fans. After these measurements, a base ventilation model was created and established as the system baseline. Changes to the ventilation system were modeled, and their effects on the power demand were projected. The results of the study showed that several improvements were possible which may significantly improve the efficiency of the ventilation system and reduce mine electricity demand.INTRODUCTIONIn 2017, a ventilation study was conducted in accordance with the Independent Electricity System Operator Industrial Accelerator Program (IESO IAP) at a mine in Ontario, Canada. The IESO IAP is designed to assist eligible transmission-connected Canadian companies operating in Ontario to fast track capital investment in major energy conservation projects. The program will provide financial incentives to encourage investment in innovative process changes and equipment retrofits to reduce electricity consumption on the provincial system and to help companies become more competitive by positively impacting their bottom line. There are now four initiatives under the Industrial Accelerator Program:1. Retrofit2. Process & Systems, including Small Capital Projects3. High Performance New Construction4. Energy Managers – a new initiative under the Industrial Accelerator ProgramWithin the program, companies may propose energy saving changes to their current systems where applicable and appropriate. Companies may then be awarded funding to implement the proposed changes. The program allows partial financial compensation to implement certain energy saving changes that would otherwise not be considered due to high capital costs. For larger projects, such as underground mine ventilation systems, a detailed engineering study must be submitted. This study must detail each energy saving change or measure, its savings, and calculate the financial incentives using the IESO IAP Payment Structure. The payment structure for a project is an amount equal to the lowest of the following (Independent Electricity System Operator, 2015):"

Jan 1, 2019

By Ming’an Wei, Qifu Duan, Jianmin Wu, Lusheng Zhou, HMR Group Limited / HMR Technology Canada Ltd., Wenjian Wu

"The development and industrial applications of magnetic liners have been around for decades. A Swedish company Skega first introduced rubber magnetic liners, and then followed by the Chinese invention of metal magnetic liners. Traditionally, both liners were used in secondary ball mills and regrind ball mills for industrial applications, especially for ores containing magnetic materials. Mostly steel balls or equivalent forged steel balls, usually below 60 mm in diameter, were used as grinding media. With the development of mineral resources over the years, SAG mills and larger ball mills have become the dominating components for comminution circuit design. Due to the development of larger diameter ball mills and thus larger ball charge diameter (up to 80mm) especially in non-ferrous metal mining operations, the application of magnetic liners have been very limited. Based on “Magnetism theory” and the development of new materials, the HMR Group Limited has been conducting researches on examining the structures of magnetic liners, associated materials and magnetic circuits which led to the invention of the Nano Alloy Steel Magnetic Liner (NSML). Recently, NSML had a successful application in a 5.5 m diameter × 6.5 m ball mill at the Erdenet Copper Mine in Mongolia. The NSML successfully handled a ball size up of to 80 mm, while achieving a service life of nearly 24 months, which is almost 3 times wear life of the original manganese steel liners.INTRODUCTIONDuring the development and utilization of mineral resources, mineral processing is an indispensably operation. The effective separation of various useful minerals depends on sufficient monomer dissociation of minerals in the ores. The crushing and grinding operation is prior operation of mineral processing. Ball mills are used in different concentrators. As the main consumption parts of mill, liners have been studied constantly. As a new kind of liners, magnetic liners besides can meet the requirement of production, and also have characteristics with maintenance-free, saving energy and increasing efficiency. So the magnetic liners are worth to be spread and applied world widely."

Jan 1, 2016

By Nehad Elsafty

It is always necessary to expand existing buildings, so that they could meet the growing societal needs. Compared with demolishing them and then constructing new ones, the expansion of existing buildings could not only reduce project cost, but also save the use of energy and raw materials in projects. Therefore, it is widely adopted in most under-developed countries. However, the expansion of existing buildings is not an easy task. It has been involved with a lot of issues in defining the scope of work, planning landscape, managing construction activities, etc. This paper investigates the potential challenges in expanding existing buildings. The project of expanding the Al-Agoza Hospital, one of the biggest and oldest hospitals in Cairo, Egypt, is selected as a case study. In the case study, the project documents have been carefully reviewed. The project engineers and the health-care professionals working in the hospital have been interviewed. This way, the point of views from the owner, the architect/engineer, and the contractor have been taken into account. Several lessons are learned through the discussion with these people. The results from this paper are expected to provide pieces of useful advice and suggestion for the expansion of existing buildings in the future.

Aug 1, 2013

By J. Lipp

The lion share of lithium produced globally originates from South American salars. The standard operation for lithium production utilizes an array of evaporation ponds. This process consume vast areas and is either very slow when relying on solar evaporation - roughly 18 months of residence time; or with very high energy consumption since over 90% of initial water volume needs to be evaporated. A new technology, based on solvent extraction was developed. Results indicate a distribution coefficient up to 30, and selectivity greater than 1,000 towards Na extraction. The loaded solvent is stripped using a strong mineral acid, and the product solution is the lithium derivative of that stripping acid. Utilization of this new LiSXTM technology results in reducing the area needed for a commercial plant as well as reduces the residence time. In addition applying different stripping acids can diversify the product line of such facility.

Jan 1, 2014

By L. P. Connolly, M. J. Fraser

"Hydraulic transport of solids has long been an important technique in mining and beneficiation. More recently, slurry pipelines have proved to be economic for longdistance overland transport of many commoditieis, including iron ore concentrates and coal. Now, the Marconaflo system brings the many advantages of hydraulic transport to bulk storage, loading, transportation and unloading of ships and other carrying equipment, thus providing important new means for delivering mineral commodities to market. In this paper, the authors describe the Marconaflo system and the potential economies which can be realized when applying it for loading, transporting, storing, reclaiming and blending a variety of mineral commodities, using several commercial installations as examples."

Jan 1, 1972

By John F. Gartner

"Traditionally, the geologists of Canada have been occupied with the tasks of finding new mineral bodies, locating gas and oil fields or hunting for economic deposits of industrial minerals. A very minor percentage of graduate geologists have applied their skills to solution of the ""urban blight"" or employing their understanding of ""Nature"" for the optimum use of land by mankind. However, things are changing quickly. The role of the geologist in the planning process is being established. It is an exciting time! Geologists are now being consulted on a wide range of urban planning problems. These vary, tor example, from assessment of the geological environment for the new communities of Erin Mills and Meadowvale, which will have total populations in excess of 100,000 people (truly a satellite city), to a complete geological/ geohydrological assessment of the new sanitary landfill for the city of Guelph.Use of geologic techniques and methods for urban studies must be enhanced with certain skills not taught, in the past, to the geologist. These include airphoto interpretation, soil mechanics, geohydrology, municipal engineering and highway engineering to mention a few. The geologist has the unique training to assess the natural environment and to discover, warn and explain the implications of man's attempt to command his environment."

Jan 1, 1972

By T. Möller

Grinding mills are the heart of the mineral processing plant, and are production-critical machines which are required to achieve high availability. Liner wear life and a liner design that promotes ease of installation are important variables to achieve a high level of mill availability. Increased mill size results in more mill internal surface to protect, and more liner components to install and remove. This drives designers toward an increase in liner size to minimize the number of components to be installed by the liner handler. The liner attachment method can also have a large impact on mill availability as well as safety during installation. This paper outlines the experience from the development, installation and follow-up of liners installed in two 38' x 45' AG Mills at Boliden Aitik in Sweden. A new Poly-Met shell liner concept has been developed to minimize the number of liner components. The new Poly-Met shell liner components are made much larger than conventional Poly-Met or steel liners. This reduces the number of components to be installed/removed by the liner handler and helps to minimize installation time and consequently down- time. A new attachment system has also been developed to eliminate the need for the installation crew to be in the ?drop-zone? of the shell liners while installing the liner bolts. One interesting aspect of this project was the requirement to predict liner life for these new large format AG mills. The existing 22' diameter mills at Aitik provided a base-line reference for this purpose, and DEM studies were used in the project development stage to predict the wear life of shell liners for the new 38' diameter AG mills. The results from this study are included.

Jan 1, 2012

By R. H. Waddington

Historical The limitations of reverberatory furnace operation have prompted many investigators to consider electric furnaces for melting electrolytically refined cathode copper. In the majority of cases where experimental work was performed, the furnace used was of the granular resistor, induction, or indirect-arc rocking type, and attempts to adapt the three-phase direct-arc furnace to copper melting appear to have been relatively few. In 1935, the International Nickel Company of Canada, Limited, carried to an advanced stage its experimental investigation of continuous melting of copper in the three-phase direct-arc furnace, and demonstrated that this process was technologically and economically practicable. Trial operations were conducted at the Huntington, W.Va. works of the Company, and were followed by the installation at Copper Cliff, Ontario, in 1936, of a full-scale unit for commercial operation. Two years later, a second unit was installed -which raised the electric melting capacity to a point permitting complete replacement of the coal-fired reverberatory furnace operation in the production of refined copper castings.

Jan 1, 1946