Search Documents

By M. E. Holter

"Limestone-bearing strata are exposed in seven areas of Alberta, each situated adjacent to rail and road facilities. Six of these centers are located along the eastern edge of the Foothills and Front Ranges of the Rocky Mountains in western Alberta. The other is in northeastern Alberta, along the eastern margin of the Alberta Basin. High-grade limestones are present in Middle Cambrian, Upper Devonian and Mississippian strata. Middle Cambrian (Eldon Formation) limestones have been exploited only in the Exshaw area west of Calgary, where they formerly were used for lime production. Limestone beds of the Upper Devonian Palliser Formation are exploited at Exshaw and at Cadomin in west-central Alberta for the manufacture of cement. Reserves of high-grade limestone also are available in the Palliser Formation near Crowsnest Lake in southwestern Alberta and near BrUle, west of Edmonton. Upper Devonian limestones of the Waterways Formation are widespread in the Fort McMurray area of northeastern Alberta, but available data indicate they are of inferior quality to the limestone deposits of the Rocky Mountains regions. The Mississippian Livingstone Formation contains large reserves of high-grade limestone at several localities in the Rocky Mountains and Foothills. Commercial development of the unit is now underway at Crowsnest Lake and at Exshaw for lime production, and future exploitation of these beds is feasible at Blairmore and Nordegg."

Jan 1, 1973

By C. I. Walker

Field tests at a number of large mineral processing operations have been undertaken to better understand the wear life impact of different aspects of pump design, materials of construction and maintenance procedures. Data are presented for wear rates, and typical result variability is explored. To improve the availability of pumping equipment in a milling circuit it is not only important to improve the wear life, but also reduce the variability in the wear life of components so that the incidence of premature failure is lessened. Localised gouging wear due to flow separation and turbulent eddy formation is often the point at which part-holing occurs. A number of improvements to the design of pump impeller and throatbush (suction side liners) to reduce the localised gouging wear are outlined. Also, results are presented on the use of composite materials (mix of metal, rubber and ceramic) for throatbush materials to protect specific areas against wear.

Jan 1, 2012

By John R. Hayes, Kebbi A. Hughes, John Rowson, Peter E. R. Blanchard, Jeremiah C. Beam, Andrew P. Grosvenor, Arthur Situm

Uranium ore bodies contain elements within mineral phases that need to be disposed of responsibly. Solid waste can be placed in a tailings management facility (TMF) to contain the waste elements and limit interactions with the environment. It is important to understand how the chemistry of the tailings evolves throughout the lifetime of the operations that feed the TMF and after the site has been decommissioned. The objective of our collaboration with Orano Canada was to study how the tailings from the TMF located at McClean Lake, Saskatchewan change over time. This manuscript discusses our use of X-ray absorption spectroscopy (XAS) and X-ray microprobe to study the fate of Mo and Ca in the tailings. Mo is considered an element of concern (EOC) and it is necessary to determine if a stable solid Mo-bearing species forms. Thermodynamic modeling suggested that aqueous Mo would precipitate over time as powellite (CaMoO4). Comparing Mo K-edge XAS spectra from the solid tailings to the aqueous Mo concentration in the pore water showed that powellite did form and that this did result in a decrease in the aqueous Mo concentration over time. Further, it has been proposed that Ca2+(aq) can react with bicarbonate ions in the pore water and precipitate as calcium carbonate (e.g., CaCO3). This reaction would limit the aqueous bicarbonate present in the tailings that could react with uranyl ions to form soluble uranyl-carbonate complexes. We have identified several trace Ca-bearing species, including carbonates, in the tailings using XAS and X-ray microprobe.

Jan 1, 2020

By G. W. Clark

"The mining of the ore bodies at Rabbit Lake has in the past been by the open pit method. This method is presently being used to develop the B-zone and will continue into the future with the development of two smaller ore bodies, the A-zone and D-zone. The Eagle Point orebody will be developed by an underground method which will provide production and employment into the next century.The ore bodies at B-zone, A-zone and D-zone are unique in that they are located under Wollaston Lake. To permit mining by the open pit method a steel-celled dyke has been constructed around the north end of the B-zone. This same dyking method will be used for the A -zone and D-zone. INTRODUCTIONMine development at Rabbit Lake commenced in 1970when a detailed engineering feasibility study established the viability of the Rabbit Lake deposit. In 1972 construction of the mill and camp site began. Construction materials were seasonally hauled to the site over a winter road until November 1973when the government of Saskatchewan completed an all-weather road to within six miles of the operation.In October 1974, stripping of the Rabbit Lake open pit began with the removal of overburden and lake bottom sediments from the previously drained Rabbit Lake. The first ore was processed by the mill in June 1975and by October the mill was producing three million pounds per year. The design capacity of five million pounds annually was first achieved in 1977 and maintained until 1981, when lower ore grades resulted in lower production rates .It was clear when mining at Rabbit Lake began that, without additional reserves, the Rabbit Lake operation had a life of less than 10 years. Exploration, therefore, continued in the immediate area in an attempt to discover additional uranium mineralization."

Jan 1, 1989

By E. E. Mueser

As Mr. Lundberg has already ably covered the theory of various methods of electrical prospecting, I shall confine my remarks to a consideration of the features which must obtain in an electrical prospecting method in order that it may be useful from a practical standpoint. These remarks I shall make with particular reference to the Elbof method. The successful application of all these methods rests, in the first place, upon the possibility of correlating theory, or empirically established facts, with the field data. Their practical usefulness, however, requires that the technique of making the field observations, and the procedure itself, be such that the method may be applied to large areas, under normal average conditions. The method, therefore, should not involve excessive preliminary labour costs to prepare the ground for actual prospecting work, nor should the prospecting work itself be so slow that its cost, when applied to extensive areas, becomes prohibitive. Moreover, it should be possible to apply the method even under difficult terrain conditions, such as rough topography and dense vegetation. It may be said of most of the methods referred to in the preceding paper, that, while they are interesting and theoretically sound, they fail to meet such practical requirements as I have outlined.

Jan 1, 1926

By A. H. Lang

"The name Barkc:rville district is applied loosely to the gold-bearing area around the historic town of Barkerville; the first mining camp in western Canada. The region is partly in the Cariboo mining division and partly in the Quesnel mining division. It contains two producing lode gold mines; the Cariboo Gold Quartz and the Island Mountain; and numerous other deposits. The regional structural pattern is outlined in this paper; the structural details of the producing mines are described in the papers that follow.The discovery of rich placer deposits in this district in 1860 was followed by the Cariboo gold rush. Placer mining in the area flourished until 1875 and then declined as the shallow diggings were exhausted, but important operations are still active. The total placer production amounts to about $50,000,000. An extraordinary number of quartz veins outcrop in the district, but many have only a small gold content. The miners soon recognized that the placer gold must have been derived from the erosion of these veins, and some directed their attention to the possibility of quartz mining. The erection of a 4stamp mill in 1876 was the first attempt at ore reduction in British Columbia, exclusive of arrastras. Efforts to mine the Cariboo lodes on a large scale were not successful, however, until 1933, when, due to the pertinacity of F. M. Wells and to the increased price of gold, the Cariboo Gold Quartz mine commenced production, followed by the Island Mountain mine in 1934. This success led to development work at many properties in the district, but the only ones that have reached production to date are the Columbia Tungstens, where scheelite has been mined intermittently since 1937, and the Cariboo Hudson, from which gold was produced in 1938 and 1939."

Jan 1, 1954

By O. Hall

STOPING at Noranda" is a sequel to "Mining at Noranda". "Mining at Noranda", presented in 1937 (1), sketches Noranda's history, metallurgical problems, exploration, mining methods, mining details, pillar extraction, and costs. "Stoping at Noranda" deals in greater detail with our stoping, the use of sub-level drifts instead of benches, and the drilling out of the stopes with jointed rock drill steel and diamond drills. Sun-LEVEL DRIFT STOPING: Sub-level drift stoping is almost universal throughout the mine and is the standard sroping method in both sulphide ore and rhyolite flux ore. The features that have led to the adoption of this standard are: (1) Continuous symmetrical drilling in sub-level drifts with no delay for blasting. (2) Large-tonnage blasts Saturday night after the drillers have left. (3) Comparative freedom from gas and smoke during the working days. ( 4) The daily safety achieved by having all stope drilling done in drifts. (5) The safety and security achieved by drilling out stopes, floors, and pillars before there is any weighting or cracking.

Jan 1, 1939

By A. K. Alzo?ubi

Block toppling in natural rock slopes has been under investigation since the 1970?s. De Freitas and Watters (1973) introduced the term ?toppling? to describe the movements of rock slopes by rotation in steeply dipping beds. The Lornex pit case history from British Columbia (Canada) was chosen to study the effect of mining on the stability of toppling rock slopes. A discrete element approach that allows fracturing of intact material was applied successfully to model the composite rock slide-rock topple movement. Three main movement modes were observed in the field and the numerical model; the sliding of the top of the slope exposed normal scarps, the toppling at the middle part of the slope exposed obsequent scarps facing opposite to the slope face, and dilation of the rock caused by fracturing at the toe formed loose material. The development of the rupture surface at the toe of the slope was traced and did not evolve into a continuous rupture surface throughout the slope both in the field and the numerical simulation. Good agreement was achieved between the deformations recorded in the field and the numerical simulation.

Jun 1, 2012

By V. ?. Chanturiya, I. Zh. Bunin, M. V. Ryazantseva

"Surface changes in naturally occurring metal sulfides (pyrite, arsenopyrite, sphalerite, chalcopyrite, galena, and molybdenite) due to treatments from high-power electromagnetic pulses (HPEMP) at varying times were studied using X-ray photoelectron spectroscopy. Analysis of the obtained results revealed common patterns and differences in surface transformations. The transformations were found to include two main stages. The first stage was observed at low treatment intensities (up to n ~103 pulses). At this stage, formation and accumulation in the surface layer of the nonstoichiometric sulfide phase, oxides and hydroxides, as well as elemental (polysulfide) sulfur and/or metastable sulfur species (thiosulfate, sulfite) was observed. The second stage (N = 3·103 pulses) is characterized by thermal removal of sulfur species and renewal of the mineral surface (sulfidization).It was found that the chemical changes of the sulfur on the surface layer of pyrite, arsenopyrite, chalcopyrite included accumulation/formation of S0 (Sn 2-) at the first stage of the transformation, followed by its removal. An increase in the surface concentration of elemental sulfur for pyrite and chalcopyrite was 10–12% while arsenopyrite was approximately 5%. A more complicated chemical change was observed for sphalerite and galena, that included formation/accumulation of metastable sulfur species (thiosulfate, sulfate) at the initial stage (up to 103 pulses) and during longer treatment times, the sulphur is reduced back to its initial state (sulfide or disulfide). The increased concentration of S0 sulfur, compared to the original sample, was only 3% in galena and sphalerite.The application of HPEMP treatment to improve flotation selectivity is supported by singlemineral flotation tests. Changes in flotability as a result of HPEMP treatment are principally explained by surface phase changes that resulted in higher adsorption activity."

Jan 1, 2016

By E. Brzychczy

Artificial intelligence techniques are ever more frequently implemented in the modern world. One of their numerous uses is supporting enterprise management. Intelligent techniques and intelligent information technology (IT) systems can be implemented in mining-related issues as well. The author of this article concentrates on supporting the process of planning mining operations by intelligent systems and techniques. The author also underlines the importance of knowledge accumulation in a mining enterprise (especially tacit knowledge) as well as its efficient storing and using. Additionally, the author provides a short description of characteristics of intelligent IT systems and indicates their capabilities in planning mining operations. She presents two solutions, namely: an advisory system which supports the process of planning preliminary works and exploitation works in hard coal mines, and a method of modeling and optimizing mining operations. Finally, the author indicates a few possible future development trends of intelligent systems - the intelligent systems of decision support.

Aug 1, 2013

By D. C. Carter, J. P. Anderle

"Exploration drilling of evaporite sequences in eastern Canada has undergone significant changes in equipment, techniques and philosophy since the early 1970s. The result has been the recovery of full-size cores from properly conditioned and stabilized holes, high quality open hole geophysical logs, and high quality metallurgical samples. The majority of modifications have resulted from the necessity to preserve the integrity of the evaporite deposit, and thus ensure the potential development, combined with the need for cost-effective high quality information. This is particularly evident in the priority placed on the development of non-erosive drilling fluids, casing and cementing procedures. The results are applicable to diamond drilling exploration of evaporite deposits anywhere in the world.IntroductionThe majority of current technical and scientific literature and expertise available on such subjects as drilling fluids or cementing procedures is applicable to large diameter, deep (several thousand metres) oil-field type drilling . The differences between oil-field drilling and wire-line core diamond-drilling are dramatic: large diameter, deep holes drilled with a low rpm tricone bit using large volumes of fluid pumped through a large annulus versus small diameter, shallow (less than 600 m) holes drilled with a high rpm diamond-set core bit using small volumes of fluid pumped through a small annulus. Exploration drilling of evaporite sequences in eastern Canada in the early I970s was conducted using oil-field equipment and techniques to complete holes of moderate (1000 m to 1500 m) depth . The prohibitive cost of these operations has necessitated that subsequent exploration drilling employs modified diamond-drilling equipment and techniques developed as part of a transition away from oilfield methodology. The result has been full size core, recovery approaching 1000/0 and the ability to run open hole geophysical logs; a combination of factors enhancing the collection of high quality information (Carter, I989a)."

Jan 1, 1990

By A. R. Naji Meidani, A. Cameron, A. Richardson, M. Isac, R. I. L. Guthrie

The supersonic core of shrouded jets remain coherent over longer distances vs conventional supersonic jets. This phenomenon should allow for greater penetration of oxygen into slag/steel reactor systems. As such, they hold the promise for faster slag/metal mixing in BOF type metallurgical reactor systems, possibly creating greater surface area/volume ratios of reacting phases, and thereby faster kinetics, as compared to conventional supersonic jet systems. In order to assess the potential of shrouded supersonic jets versus their conventional counterparts, an experimental investigation of impinging shrouded supersonic jets into a water model of a simplified BOF system was carried out in the MMPC's water modelling laboratory. The experimental results for three different designs of a shrouded supersonic jet nozzle have been compared in terms of greater penetration depths and reduced mixing times. Based on a novel dimensional analysis, the depth of penetration of a gas jet into a liquid bath is shown to depend on the nozzle-bath distance, the liquid's Froude, Reynolds and Weber numbers, reflecting the ratios of gravity, viscous and surface tension forces to the jet's inertial, or momentum, forces. Good agreement between the mathematical model and experiment was obtained in terms of predicted and observed depths of penetration. Further efforts have been made to study jet penetration into liquid metals. The effects of mean liquid density of slag/metal mixtures and a wide range of gas flow rates on the penetration depth were investigated theoretically. The results show that the penetration depth can be increased with increasing gas flow rate and decreased bath density.

Jan 1, 2004

By M. Rudolph, T. Leißner, TU Bergakademie Freiberg, C. Mämpel, R. Möckel, M. Embrechts, T. Leistner

Tin-mining activities have taken place in the region of the German Erzgebirge (Ore Mountains) for over hundreds of years up until 1991. For long times, gravity separation processes used to be the dominating beneficiation approach in those mining districts to recover cassiterite, the main tin-bearing mineral. For fine (< 100 µm) and very fine (< 20 µm) particles these approaches might not represent effective techniques, significant valuable materials could not be recovered and reported to tailings, where it was subsequently disposed. Thus, there are substantial amounts of cassiterite still present in these tailings disposals, most of it as very fine particles with already high degrees of liberation. That fact brings these tailings disposals into focus for potential reprocessing using beneficiation approaches, which are more sensitive to fine and very fine particles. In this paper we present results concerning the laboratory-scale treatment of material from exemplary heaps of the former Altenberg and Ehrenfriedersdorf mining sites using various flotation methods (including conventional froth flotation and oil-assisted flotation). Different size ranges of the material were previously prepared in order to investigate their response to the different techniques. For the study, special emphasis is put on agglomeration flotation, an oil-assisted flotation method. Therefore, an aliphatic oil phase of alkane basis is used to either selectively aggregate or collect the cassiterite particles. Recovery and flotation performance results are presented with respect to different process parameters: various collectors (including sulphosuccinamates and phosphonic acids) and depressants (including sodium fluorosilicate and oxalic acid) regime, oil dosage, agitation time and pulp density during oil/pulp agitation. Furthermore, the oil/particle aggregation behavior is analyzed via particle image analysis and, additionally, collector adsorption characteristics are investigated by contact angle measurements and zeta potential analysis. The data obtained is correlated with the testwork results achieved in order to interpret the flotation response of very fine cassiterite particles.

Jan 1, 2016

By Etienne Roy Grégoire

Since the early 1990s, the Canadian mining industry has been increasingly defined by the signing of Impact and Benefit Agreements (IBAs) between mining companies and Aboriginal peoples. While these agreements are intended to complement the legal system, they also serve to establish the legitimacy of mining projects and to encourage the harmonious integration of these projects into their social and environmental contexts. Beyond their practical implications, what are the effects of such agreements on the ability of Aboriginal communities to access the institutional space where the authorization of mining projects and the conditions of their implementation are decided? Can we view IBAs as a preliminary step towards the operationalization of the principle of Free, Prior and Informed Consent? This paper aims to explore the potential of IBAs as a sustainable solution to the legitimacy issues that result from the implementation of the formal regulatory framework governing mining activities in this jurisdiction. We highlight what constraints and opportunities the James Bay and Northern Quebec Agreement (JBNQA) engenders for local communities and draw attention to the ways in which the negotiation of the Raglan IBA and the environmental evaluation processes act upon each other. We find that certain structural problems - and problems of legitimacy ? related to mining in Northern Quebec cannot be solved by the sole signature of an IBA, which suggests the need for caution when considering such agreements as a panacea. The Raglan case demonstrates that IBAs, like other modes of regulation relying on the direct interface between companies and communities, would benefit from a stricter framework and more explicit ties with official regulation channels.

Aug 1, 2013

By M. Mbonimpa

Field experimental cells were constructed in 2007 to assess the performance of different cover scenarios for the reclamation of the Parc 1 tailings disposal facility at the Westwood-Doyon Mine site (Abitibi, Quebec). Three configurations of cover with capillary barrier effects (CCBEs) with different thicknesses and material types for the moisture retention layer (MRL) were studied. MRL with 80 cm till, 40 cm till, and 40 cm clayey silt were used for cell nos. 2, 3, and 5, respectively. The capillary barrier layer (CBL) and drainage and protection layer (DPL) of the CCBE consisted of 30 cm gravel. A reference cell without cover was also constructed to compare the geochemical performance of the CCBEs. Due to an unexpected flooding in the leachate exit area of the cells in spring 2008, the cell instrumentation for hydrogeotechnical monitoring was postponed to spring 2009. Changes with time in volumetric water content, suction, soil oxygen concentration, and temperature were measured at different depths. This paper presents and discusses preliminary results obtained from spring 2009 to autumn 2010. In all cases, the degree of saturation Sr is lower in the CBL than in the MRL, indicating the presence of capillary barrier effects at the interface of these layers. Cell nos. 2 and 5 showed hydrogeotechnical behavior typical of an effective CCBE, with Sr maintained above 85% in the MRL and lower than 30?50% in the DPL and CBL. Based on the obtained results, and as expected, MRL thickness and the type of construction material used appear to affect the hydrogeotechnical behavior of the CCBE. Oxygen concentration profiles through the CCBEs were used to estimate the oxygen flux, and results indicate that cell nos. 2 and 3 performed better than cell no. 3. CCBE performance is currently being investigated using the geochemical monitoring data.

Aug 1, 2013

By F. J. Guevara

A two-dimensional mathematical model for fluid flow and heat transfer in a sixin- line electric smelting furnace was developed to study the effects of temperature on slag viscosity in both the liquid and mushy zones. The model focused on the fluid dynamics of the molten slag and the effects on the formation of a slag freeze layer on the hot face of the furnace wall. Previous experimental and mathematical work, carried out under Ra number of 109 and using a fluid with Pr number of 65, showed that it is possible to mathematically describe the freeze layer formation over a vertical wall using a fixed-grid model. The chemical composition of the slag was taken into account through its effect on the viscous activation energy as well the solidus and liquidus temperatures. The results show that the flow pattern is strongly modified in areas of high viscosity, in front of the cooling system and at the slag-matte and slag-calcine interfaces. The results are discussed in terms of heat flux over the refractories and their effects on cooling system design.

Jan 1, 2007

By V. Labiouse, M. Souley, N. Lafrance, C. Auvray

"Chalk rocks have been used for centuries as a strong building material and for the production of lime. The shallow underground room-and-pillar quarries where the chalk was extracted are now abandoned and endure the effects of time and weathering, increasing their risk of collapse. The risk of instability, involving natural or anthropic underground structures, is an issue for more than 10 000 towns in France.In order to investigate the causes of underground quarry collapse and to aid prevention strategies, we carried out a study of the physico-mechanical behaviour and ageing of chalk in abandoned pillars in two underground quarries, in situ-instrumented by INERIS, in the Parisian Basin, France. Core samples were drilled horizontally from pillars in the Saint-Martin-Le-Noeud dolomitic chalk quarry (Oise, France) and the Estreux glauconitic chalk quarry (Nord, France).Uniaxial tests were performed on dry and saturated cylindrical plug samples extracted perpendicular to the cores at regular distances along their lengths. Physical and mechanical properties were obtained. The dolomitic chalk (Saint-Martin-Le-Noeud) exhibits variation in mechanical and physical properties with horizontal pillar depth. Both density and compressive strength seem to increase outwards from the pillar-core to the pillar-wall. This is the opposite of that would be expected from a purely mechanical point of view. SEM analysis revealed progressive degradation and homogeneity of the grains from the edge to the inside of the pillar. At the pillar wall, the crystal faces are well-defined, almost euhedral, and the grains are of variable size. In contrast, at the inside of the pillar, crystals are finer-grained and are anhedral with highly degraded edges. In the physico-mechanical tests and SEM analyses performed on the Estreux samples, no significant variation was observed between the pillar-walls and pillar-core. However, dissolution marks were observed along the entire length of the half-pillar core."

Jan 1, 2015

By W. A. Bain

"AbstractProduction from the Excelsior Reservoir has amounted to approximately one million barrels. This production has caused a 'Pressure •drop of 10 p.s.i. from the original pressure of 1,245 p.s.i.g. Volumetric balance calculations indicate that the pool as being produced by a water drive whose strength is •probably unsurpassed in Western Canada. It has also been shown by 'unsteady state' calculations that the reservoir will still be above the saturation pressure of 915 p.s.i.g. at the time of depletion. The average permeability of the producing formation is approximately 1,000 millidarcys and, consequently, well draw-downs are very low. The field is essentially a bottom-water drive and calculations have shown that gravity drainage will greatly assist the recovery of oil. Water flooding data on several cores •have placed the flushing efficiency at •approximately 50 per cent, which indicates a recoverable oil-in-place of 17.7 million stock tank barrels. Calculations and field data indicate that the MER for the early life of this field is probably as high as 8,000 to 10,000 stock tank barrels per day.IntroductionTHE EXCELSIOR NISKU oil reservoir is located about twenty miles northeast of Edmonton. The field was discovered in November, 1949, by Imperial Excelsior N.o.1 well, in Lsd. 13, Sec. 3, Twp. 56, R. 22, W. 4, at a depth of 3,850 feet.Since discovery, development has continued on a 40~acre spacing pattern. At the end of 1951, drilling over approximately 80 per cent of the estimated productive area of 1,680 acres had established 32 we1ls capable •of production. The field •has been fairly well delineated by dry holes on all but the eastern flank ."

Jan 1, 1952

By N. J. Shackleton, N. A. Chapman, V. Malysiak, C. T. O’Connor

In this study, the effect of using conventional crushing and high-pressure grinding rolls (HPGR) in combination with dry or wet milling was investigated using a base-metal sulphide (BMS) sphalerite and a platinum group mineral (PGM) ore to determine how these processes affect the flotation performance. In sphalerite, irrespective of the crushing procedure (HPGR or conventional), dry milling resulted in the highest grades and recoveries of zinc, whereas in PGMs, similar treatment produced the poorest results. The results were investigated further by the effect of factors such as percentage liberation and particle size on the flotation results.

Jan 1, 2012

By S. Amira

The corrosion behavior of high pressure die-cast and thixocast AXJ530 magnesium alloys has been investigated in 0.05M NaC1 solution at pH 6.0 using potentiodynamic polarization tests, electrochemical noise (EN) technique, electro-chemical impedance spectroscopy (EIS) and scanning reference electrode technique (SRET). The behavior of die-cast and thixocast specimens were compared using each of these techniques and the results discussed. Further tests have been carried out with die-cast AZ91D alloy to better compare and interpret the results. Experiments indicate that the thixocast specimens of AXJ530 alloy have a better corrosion resistance than those of die cast alloy in neutral solution.

Jan 1, 2006