Search Documents

By Roméo Roussin

"The yearly production from the Asbestos Hill pit is 1,550,000 tons of asbestos ore, with a yield varying between 18 and 20 % . The orebody was exposed at the top of a hill, and initial production started without having to remove any overburden. The projected ratio of barren rock to ore, based on the present orebody, was 2 to 1. However, as it was necessary to push back the upper benches, this ratio has changed to 3 to 1. The final pit will be 2,300 feet long by 1,000 feet at the longest and widest points. The final depth will be 680 ft. A pit slope stability study was carried out and an average wall angle of 60-70 degrees must be maintained. Preshearing of final pit limits will produce good wall stability. Permanent access ramps will be 60 ft wide, with an 8 % maximum grade. Geological conditions and the low rock temperature are the major causes of the operation's drilling and blasting problems."

Jan 1, 1976

By W. Holdsworth

The flotation mill of Dentonia Mines, Limited, at Greenwood, B.C., went into operation on April 20th, 1934, and by October 11th a total of 15,000 tons of ore had been treated. It is intended in this paper to describe briefly the operation and to give some of the operating data which have been gathered. The metallic minerals in the Dentonia ore are pyrite, chalcopyrite, galena, and, occasionally, native gold, and the gangue includes chloritic material, vein quartz, and calcite. Pyrite makes up about 90 per cent of the metallic content of the ore, in which it is disseminated as irregular grains and well-formed cubes. An average analysis of the ore is: gold, 0.27 oz. per ton; silver, 1.73 oz. per ton; copper, 0.12 per cent; lead, 0.31 per cent; and zinc, trace. From the mine ore-bin, situated near the portal of the tunnel at the mine, the ore is hauled by motor truck to the mill, a distance of three-quarters of a mile, and there dumped into the receiving bin, which has a capacity of fifty tons. The hauling is done during one eight-hour shift, commencing at 7 a.m. The maximum size of the ore fed to the mill-bin is ten inches. Lumps larger than this are broken by sledge hammer to pass through grizzly bars, spaced ten inches apart, installed above the bin. The ore is drawn from the bin by a 30-inch, 6-ply conveyor belt, 18 feet 6 inches long. In the near future, when the cross-cut tunnel is completed, the ore will be trammed to the receiving bin. This will effect a considerable saving in cost. At the same time, the bin will be set back several feet, so that the length of the conveyor belt may be doubled. This will make efficient ore-sorting possible, and so ensure a minimum of waste rock in the mill feed.

Jan 1, 1935

By S. Bozorgi, K. Anders

"The automotive applications of heat treatable AlCu cast alloys are designed for performance at high temperature, which can be improved using specially alloying element as well as different heat treatment. In this research work an effect of alloying element such as Cu, Ni and heat treatment on microstructures and mechanical properties of AlCu alloy were investigated using optical microscope (LIMI), scanning electronic microscope (SEM) equipped with energy dispersive X-ray detection (EDS), Differential scanning calorimetry (DSC) and mechanical testing. It was found that during solidification most of the elements Cu, Mg and Ni segregated at the grain boundaries in the form of Al2CuMg or Al7Cu4Ni and a very small part of Cu and Ni element dissolved in the FCC-Al matrix. The latter is not completely reclaimable for strengthening mechanisms in FCC-Al matrix in its as-cast state. The results of mechanical test show that yield strength and ultimate tensile strength increases after heat treatment significantly compared with the as-cast state. Furthermore the mechanical properties at elevates temperature (240°C) is higher with higher Cu+Ni+Si containing alloys compared with the less Cu+Ni+Si containing alloy.INTRODUCTION Due to the high strength-to-weight ratio, high strength and ductility at room- and elevated temperature, AlCuSi cast alloys are widely applied in the automotive industries specially for producing cylinder head and engine block, where modified alloys with enhanced metallurgical properties are always needed to satisfy the ever increasing demands for the applications. The AlCu based cast alloys can be strengthened by age hardening. The precipitation processes from which this hardening is derived can be attributed to the presence of selected trace element additions or micro alloying, which can change the process or kinetics of precipitation in age hardenable AlCu cast alloys (Polmear, 1998; Morris, 1991). Furthermore their strength is mainly controlled by the aging process through the precipitation and growth of very fine precipitates of the ?'-phase (a semi-coherent, metastable form of the equilibrium Al2Cu phase) from the Al and Cu Guinier-Preston (GP) zones. Several studies have shown that solute clustering occurs prior to the precipitation of GP zones, and this modifies both the nature and kinetics of the precipitation process. The typical size of GP zones is in the order of tens of nanometers, and the chemical composition of these precipitates is not easily measured, even with a typically analytical electron microscope (Polmear, 1989)."

Jan 1, 2018

By C. D. M. Chisholm

IN discussing stope filling, or backfilling, at the Sullivan mine, at Kimberley, B.C., a brief description of the problem will first be presented. The Sullivan orebody is a replacement in quartzite, with the ore con-forming, for the most part, with the bedding. The dip of the vein, apart from local irregularities, averages about 15 degrees near the outcrop in the southwest section of the mine, and steepens to almost 40 degrees at the northeast end of the mine. The thickness varies from a few feet to over 200 feet at the widest sections. The mineable length along the strike has averaged about 4,000 feet between the 4,600 and 3,900 levels-the section under discussion in this paper. To date, 28,000,000 tons of ore have been mined by the room-and-pillar method. Prior to 1930, all ground opened up had been supported by ore pillars, left during mining operations. From that time, the recovery of the ore from these pillars has been given serious consideration. Backfilling, as being carried on today, is the result of this study and is being done for two reasons: (1) to allow extraction of the ore pillars, and (2) to minimize subsidence of the hanging-wall rock, except where forced caving is found desirable. PRELIMINARY DEVELOPMENTS LEADING TO BACKFILLING When the Sullivan orebody was first opened up, early in the century, there appeared to be low-grade sections of the vein sufficient in extent to serve as permanent support for the roof. However, as mining extended into sections of the vein that showed continuous ore over greater areas, wooden cribs, filled with waste and low-grade ore, were erected. In some stopes, these cribs were as large as 40 ft. by 100 ft. in plan and from 50 ft. to 60 ft. in height, but it was soon realized that this method of support was inadequate. As mining progressed, it was found necessary to leave ore pillars, which eventually became the sole system of support. At first, these pillars were left at irregular intervals, but later they were laid out at definite locations on the mine plans, and these locations were adhered to as closely as mining would permit.

Jan 1, 1941

By Nader Golchinfar

The V-shaped breakout zones around excavation boundary have been captured by a variety of numerical methods such as FEM and DEM methods and failure criteria such as linear Mohr-Coulomb and non-linear Hoek-Brown failure criteria. Diederichs (2007) used Hoek-Brown parameters in his spalling parameter approach; however, it is convenient to use the Mohr-Coulomb failure criterion in numerical modeling because the material parameters can easily be determined from triaxial tests. It is shown in this study that when peak and residual strength parameters as well as dilation angle are properly defined, the brittle Mohr-Coulomb failure criterion can be used to model depth of failure near underground excavations satisfactorily.

Jun 1, 2012

By H. R. Shakeri, R. Mayer, M. J. Worswick, A. Rahem

The current focus of research and development in transportation industry is to use lightweight materials such as aluminium alloys for more structural components. In this regard, maintaining safety of the passenger and vehicle is the most important; therefore crashworthiness of components made of lightweight materials must be evaluated prior to sizable application of these materials. The focus of the present study is to understand failure and damage mechanisms during the axial crushing of aluminium tubes made of A1Mg3.5Mn alloy of 2 and 3.5 mm thickness. Due mainly to complexity of the crushed tubes, a microstructural approach is considered. In this study optical, stereo as well as scanning electron microscopy techniques have been used to study damage and failure mechanisms in these types of tubes, which are essential energy absorbing components in passenger vehicles.

Jan 1, 2006

By N. Dahata

Earlier research has indicated that an addition of titanium master alloy to aluminum alloys, results in improved fillability, grain refinement and finer pores. B206 alloy differs from other alloys used in automotive industry, with lower titanium level. This paper examines the effect of alloy chemistry (copper and titanium levels) and grain refinement (A1-5`)oTi- 1%B grain refiner) on grain size, microstructure and microporosity in B206 aluminum alloy. In this study, characterization of grain size, microstructure and microporosity was carried out using light optical microscopy (LOM) and scanning electron microscopy (SEM). Results have shown that the addition of 0.05 wt % titanium resulted in grain refinement of B206 alloy. With an increase in titanium to 0.25 wt further grain refinement, much reduced pore size and uniform distribution of pores resulted. These results suggest that B206 with proper addition of titanium has a promise as an alloy for automotive casting.

Jan 1, 2007

By H. Chaouki

The aim of this work is to simulate the forming process of a green anode. For this purpose, a nonlinear compressible viscoelastic constitutive law is presented. The concept of natural reference configuration is considered. Within an isothermal thermodynamic framework, a Helmholtz free energy is proposed to take into account the nonlinear compressible deformation process occurring between natural reference configuration and current configuration. A dissipation potential is introduced in order to characterize the irreversible aspect of compaction process. Thus, the constitutive law is formulated through two equations: 1) an expression of Cauchy stress tensor and 2) a differential equation characterizing the evolution of the natural reference configuration. Material parameters are assumed to be a function of the bulk density. This allows capturing the micro-mechanical phenomena within the chosen macroscopic approach. An experimental study based on compaction tests is carried out in order to characterize the mechanical behaviour of the anode paste. A user's material VUMAT subroutine for finite element dynamic explicit analysis has been developed and implemented in the ABAQUS commercial software. To evaluate the model predictive capability, numerical simulations of the compaction forming process of anode paste were performed. Simulation results show that the constitutive law predicts the experimental trends and gives interesting physical responses. This constitutes a first step toward making a benchmark with experimental results on the forming process of anode paste.

Jan 1, 2011

By A. Galip Ulsoy, K. V. S. Sastry

"This review paper is intended to provide, the mineral process engineer with an introduction to the concepts, terminology. and practice of mineral process control. It also provides an extensive sampling of the vast body of literature relevant to this topic. The topics discussed include the principles of automatic control, instrumentation, mineral processing unit operations, process modeling and simulation, and process and plant control. IntroductionEconomically accessible higher-grade ores are being rapidly depleted, and at the same time the demand for mineral raw materials continues to increase. Mineral recovery from the remaining low-grade or finely dispersed ores requires grinding for liberation. High energy consumption during grinding and poor efficiency associated with the beneficiation of fine minerals are two important problems facing the mineral industry . These problems, coupled with advances over the last 10 to 15 years in the areas of process modeling, instrumentation, computer technology and control theory, have made automatic control of mineral processing systems an important research area(23,52,66,67,120,129,152)."

Jan 1, 1981

By R. A. L. Drew, G. Mendoza-Suarez, J. Filipi, R. Vintila, J. A. Kozinski

Economics and environmental considerations along with the increasing demand of hydrogen encourage development of novel technologies such as plasma processing of hydrocarbons and thermal cracking of natural gas. Plasma discharges, either in thermal or non-thermal regimes are expected to allow low temperature and fuel flexible on-site hydrogen generation. The main drawback of thermal plasma reformers is the high-energy consumption resulting from high-temperature operation. On the other hand, non-thermal plasma, generated by dielectric barrier discharge (DBD), is able to simulate the chemical reactions employing much lower energies than those required by thermal treatment processes. The non-thermal plasma process allows for instance, a direct conversion of methane into hydrogen and carbon black with no CO2 release. The focus of this research was on the GHG-free method of H2 generation in compact non-thermal plasma reactors using low, medium and high permittivity dielectric ceramics. A stable, non-thermal plasma was generated by placing a dielectric ceramic between two electrodes with a 25 thou gap and applying an alternating current of 1-5kHz and voltages of 4-8kV. In order to ensure energetic efficient plasmas, experiments were conducted to analyze the behaviour of different permittivity ceramics. It was found that the dielectric properties of a ceramic, when used in a DBD reactor, have a strong influence on the discharge characteristics, which in turn influence the power consumption. Higher dielectric constant resulted in higher conversion rates of methane (higher yield of hydrogen and carbon). At the same time, the mechanical properties of the dielectric material, which are closely associated with its processability, influenced its resistance to electron bombardment, as well as thermal and mechanical damage. Therefore a reliable ceramic should have good dielectric properties, in addition to good thermo-mechanical stability.

Jan 1, 2004

By J. George Gregr

"This paper gives a brief review of grinding mills installation procedures with special emphasis on future maintenance. The importance of cooperation between the customer, construction contractor and manufacturer's representative is discussed, as well as the imparlance of complying with standards, specifications and the keeping comprehensive installation records.Fundamentals of mill maintenance are explained with the aim being to maximize the equipment availability and to minimize unscheduled downtime. The paper also includes development of wear items design, based on operating conditions, drive components and bearings, and how to keep large gears healthy thus eliminating surprise failures.Experience with installation of a large gear on a 34-foot diameter mill in Lornex and successful application of a computer program for the gear alignment on the mill are given.IntroductionSuccessful operation of a concentrator begins with the engineering of the project and continues through selecting the right equipment, its installation , start-up period, and ends with final tuning of the process. machinery and the human factor into an efficient and viable industrial complex.The following is a brief review of grinding mill installation procedures with special emphasis on future maintenance. Fundamentals of mill maintenance are discussed with the aim being to maximize the equipment availability and to minimize unscheduled downtime, with some specific points on key grinding mill components such as bearings and drives.Finally, the experience is recounted with the installation of a large ring gear on a 34-foot diameter mill at Lornex, and the successful application of a computer program for the gear alignment on the mill."

Jan 1, 1985

By J. E. Udd, L. B. Geller

"Mine-shaft wire-rope discard regulations include, among other criteria, a limited amount of permissible loss-of-breaking-strength (LBS). Currently, this parameter is estimated on the basis of non-destrutive-testing (NDT) with electro-magnetic (EM) type instruments. This paper analyses the accuracy with which these estimates have, so far, been obtained in practice.It concludes that while certain types of testers have produced better results than others, the desired accuracy level has not been attained. Also discussed are the putative reasons for this situation, and appropriate actions that the mining industry might wish to take."

Jan 1, 1990

By L. Voisin, K. Yamaguchi, D. G. Mendoza, K. Ltagaki

The behavior of arsenic and antimony in the Cu-0 system was thermodynamically investigated to understand their elimination during a blister-making stage in copper smelting. Firstly, the phase relations in a miscibility gap composed of the liquid slag and copper phases in the Cu-0-As and Cu-0-Sb systems at 1523 K were established by a quenching technique. It was found that arsenic and antimony distributed preferentially into the slag phase in the miscibility gap. Secondly, the activities of arsenic and antimony in the miscibility gap of these systems were determined at 1523 K by using a double Knudsen cell - mass spectrometer method. It was clarified that the activity of arsenic in the copper and slag phases showed the negative deviation from ideality while that of antimony in the copper phase a slightly positive deviation. These data obtained in this study suggest a possibility to eliminate arsenic and antimony by means of over-blowing in a converter after discharging the slag.

Jan 1, 2007

By V. A. Leão, A. M. Silva, S. M. Bertolino, B. C. S. Ferreira, D. Guimarães

Although not considered a high risk pollutant as compared to toxic metals and acidity, environmental agencies worldwide are proposing regulations to control sulphate in effluents and drainages by setting a threshold value varying between 250 mg/L and 500 mg/L. The aim of this study was thus to compare four different techniques for removing sulphate ions from mining/metallurgy effluents. The first alternative studied was sulphate removal by precipitation as ettringite. Treating a synthetic solution containing 1650 mg/L sulphate at 22±1 ºC resulted in removals close to 85% during continuous precipitation. Sulphate sorption was also investigated using three different ion exchange resins as well as limestone. Fixed bed experiments produced sulphate loadings of up to 70 mg SO4 2-/L resin, at pH 2.0. In neutral wastewaters, limestone is also a potential adsorbent producing a maximum particle loading of 19 mg/g. Sulphate sorption on limestone seems to be an alternative to treating mine waters with sulphate concentrations below the 1200-2000 mg/L range, where lime precipitation is not effective. Subsequently, sulphate removal by sulphate reducing bacteria was also investigated and it was observed that reactor’s hydrodynamic conditions and the choice of substrate are important factors for the process. The different technical aspects of each technology are addressed.

Jan 1, 2014

By E. J. Schwarz, A. A. Winir

"Absolute magnetite contents were determined for asbestos specimens in various stages of milling by using a Faraday-type thermomagnetic balance. Comparison of these results with magnetic ratings (MR) supplied by the mining companies cooperating in this study reveals strong scatter. The main cause of this scatter is thought to be that the MR values were obtained in magnetic fields well below the saturating field of magnetite (5,000 oe). However, only the saturation moment is an intrinsic property and consequently must be used for the purpose of obtaining reliable estimates of the magnetite content. Curie points indicate that virtually pure magnetite and possibly Ni3Fe is present in all samples, and another phase, probably (Cr, Al) magnetite, is present in a few samples. The susceptibility in fields stronger than 5,000 oe is positive and falls in the normal paramagnetic range, whereas sy nthetic chrysotile exhibits weak diamagnetism. This suggests that, as a general rule, the least adulterated natural chrysotile concurs with the samples showing the smallest positive susceptibility above 5,000 oe. The magnetite appears to increase in quantity with a decrease in fibre length and to be somewhat more uniform in distribution for samples showing substantial fiberization (opening of the fibres)."

Jan 1, 1971

By E. L. Chanturiya

The research and characterisation for compositional, physicochemical, structural, electrical and flotation properties of various pyrite samples for a copper-zinc sulfide ore was carried out. Various methods were used during the research, such as optical microscopy, X-ray diffraction, electron probe micro-analysis (EPMA), phase emission analysis, routine chemical analysis, auger electron spectroscopy (AES), scanning electron microscopy (SEM), back-scattered electron images (BSE), potentiometry, and instrumental neutron-activation analysis, flotation. Analysis of obtained results established the interrelation between impurity structures and concentration of electric charge carriers in minerals, Butyl xanthate sorption and flotation yield of pyrite. The research concluded that pyrite samples differ by morphology, micro defects of structure, concentration of donor and acceptor impurities (Co, As, Sb, etc.) and conductivity parameters (thermo-electrical force, specific resistance and concentration of charge carriers The peculiarity of pentagon-dodecahedral pyrite is the high concentration of electric charge carriers (electrons) and the more negative surface potential (by 25–75 mV) in comparison to cubic pyrite. The surface of cubic varieties is more active, therefore it is oxidized in alkaline lime medium much faster, than the surface of pentagon-dodecahedral varieties. This phenomenon is caused by high reaction ability, irregular jointing and defects of cubic pyrite. This promotes the increase of calcium ion sorption on its surface and the decrease of Butyl xanthate sorption. According to this, an increase in alkalinity (lime medium) from a pH of 10.0–11.5 leads to an increase of gold content reporting to the tail of bulk flotation. Gold content is increased from 0.58 g/t (?? 9.5) to 1.9 g/t (?? 11.6), which represents an increase in gold recovery of 24.68 to 79%, respectively.

Jan 1, 2016

By DALE MacGREGOR, VERA TUREK

lndusmin Limited acquired the St. Donat quartzite deposit in 1967 to produce high-quality silica for use in the sandblasting and silicon carbide industries. The quartzite, of Grenville age, is highly friable and porous. This is due to numerous small, kaolinite-coated cavities in the quartzite; the cavities were formed through leaching, probably by rising hot solutions.

Jan 1, 1984

By Chris McBean

Due diligence mistakes ? lost opportunity ? High profile write-downs and cost overruns ? Result ? tight market for financing ? Implications for due diligence ? need to get it right ? maybe only one chance ? Where should focus be?

May 1, 2013

By K. Soldenhoff, D. Wilkins, E. Ho

In the processing of rare earth ores, a pure, mixed rare earth chloride solution is usually produced and used as the feed to solvent extraction circuits to separate the individual rare earths. Cerium(III) may be separated from the other rare earths by oxidising it to cerium(IV), which precipitates as cerium(IV) hydroxide in chloride liquors. This oxidation step may be inserted either before rare earth separation by solvent extraction or between solvent extraction circuits. Although oxidation of cerium by sodium hypochlorite has been known for many years, detailed conditions for oxidation are not readily available. The effect of hypochlorite addition, temperature, pH and cerium concentration on oxidation of cerium(III) from synthetic solutions was investigated

Jan 1, 2014

By Robert A. MacGregor

"Following several months of test work, water leaching in mined-out areas at Stanrock commenced on a production basis in February, 1963. A combination of fast high-pres-sure washing and rewashing of stopes on a predetermined cycle, and the intermittent sprinkling of low-grade heaps, using both fresh water and recirculated acid water, has proved most successful. There was also a correlation of daily sampling data points to a relationship between the leach water grade and the grade of the material being washed, the leaching time and the location along the dip. An increasing tolerance for uranium by the acid-producing bacteria is also indicated. A steady production rate of 10,000 to 12,000 lbs. of u.08 per month is being maintained, with an over-all mine water grade of 0.25 lb. per ton and a pH of 2.3."

Jan 1, 1966