Search Documents

By Gonzalo Díaz, Diego Mesa, Willy Kracht

"It is well known that frothers affect the amount of water that is transferred to the froth, which has an effect on both the froth stability and the water recovery. On the other hand, since non-selective recovery by entrainment is directly related to water recovery, it can be said that frothers have an indirect effect on flotation selectivity. Recent research on this subject has shown that the non-selective recovery by entrainment, which is characterized by the entrainment factor, is frother dependent. In other words, the entrainment factor is not unique, but depends on frother type.Having different entrainment factors implies that for the same water recovery, the amount of undesired particles reporting to the concentrate may vary if one changes the frother type, which suggests, as a possible explanation, that it is not only the amount of water in the froth what is affected by frother type, but also the froth structure.The purpose of the current work is to study the effect of frother type on foam structure (two phase froth). A quasi-2D cell operated with a slot sparger was used to study the foam structure in the presence of three different frothers: Methyl Isobutyl Carbinol (MIBC), OrePrep®549, and Octanol at the same gas flow rate and reagent dosage. The foam structure was studied using image analysis, and an algorithm based on textural analysis was developed to classify the foams. The results show that it is possible to classify foams according to the frother used, which proves that frothers have an effect on the foam structure.INTRODUCTIONFrothers are usually dosed paying attention to froth stability, condition that is commonly estimated by sight, according to the operator's criteria and experience. This happens because there is not an established procedure or technique for frother characterization, generating qualitative descriptions such as “powerful” or “selective” frothers, which lack of scientific thoroughness and remain under subjective factors. Nevertheless, several works have been done in this line of research. Moyo et al. (2007) classified frothers based on their water-carrying capacity, proving that this characteristic is related with gas holdup and frother type. Previously, Trahar (1981) had related water recovery and gangue particles recovery, defining the entrainment value (ENT). Nowadays it is known that entrainment affects both hydrophilic and hydrophobic because it is not a selective process. In the last decade some studies (for example the one of Konopacka and Drzymala (2010)) delved into different entrainment behaviours dependent mainly on the flotation type (batch or continuous, agitated or columnar, etc.), but there were no studies on the effect of frother type regarding entrainment, since Rahal et al. (2001) argued that the ENT factor was independent of the frother type and concentration, and froth height."

Jan 1, 2016

By A. A. Rafiei, J. A. Finch

A previous study comparing n-pentanol and the polyglycol Fl50 showed that the two reagents could give the same gas holdup but with different size bubbles. The finding implies that bubble rise velocity depends on the surfactant (frother) type. A study using bubble swarms supported the frother type effect but bubble interactions were a possible confounding factor. This study resolves the question by measuring the rise velocity of single bubbles of 0.8-2.5mm diameter over a distance :::: 300cm in n-pentanol and F 150. It is shown that at typical frother concentrations used in flotation that the rise velocity in n-pentanol remains comparable to that in water alone while in Fl50 the velocity is significantly reduced. The results confirm the suspected impact of frother type. It is illustrated that in n-pentanol the rise velocity does not reached terminal; while in Fl50 it does and this is the source of the velocity difference. Advances

Jan 1, 2009

By S. Malopheyev, I. Vysotskiy, R. Kaibyshev, S. Mironov

"In this work, the effect of pre-strain rolling on the annealing behavior of friction-stir welded 6061-T6 aluminum alloy was studied. To this end, the as-welded material was rolled to 10 or 20 pct. of thickness reduction prior to the standard post-weld T6 heat treatment. Three rolling directions were the 3-mm thick sheet were considered: along the welding direction, perpendicular to the welding direction, and at the angle of 45° to the welding direction. At relatively low pre-strains (10 pct.), the annealing behavior was found to be very sensitive to the rolling path, and rolling along the welding direction was most effective in suppressing abnormal grain growth. On the other hand, increasing the pre-strains to 20 pct. of thickness reduction inhibited abnormal grain growth irrespective of the rolling path.INTRODUCTION Heat-treatable wrought Al-Mg-Si alloys are widely used due to attractive combination of strength, ductility, excellent corrosion resistance and low cost (Polmear, 2006). To provide the optimal balance of mechanical properties, these materials are typically commercially available in appropriately work- and precipitation-hardened conditions (Polmear, 2006). During conventional fusion welding, however, the prior strengthening effect is totally lost due to elimination of the work hardened structure and dissolution of the strengthening precipitations. An innovative friction-stir welding (FSW) technology may partially overcome this problem. Due to the solid-state character of this process, which involves very large strains, the welded material is characterized by fine-grained microstructure with moderate-to-high dislocation density, and thus the prior work hardening effect may be preserved or even enhanced (Threadgill et al., 2009; Mishra & Ma, 2005). However, heat input associated with FSW inevitably leads to dissolution and/or coarsening of strengthening precipitates, thus giving rise to the undesirable material softening. In an attempt to restore the strength of the friction-stir welded material, the standard T6 post-weld heat treatment has been applied, but this approach was found to lead to abnormal grain growth (Malopheyev et al., 2016; Mironov, 2013, Mironov et al., 2015)."

Jan 1, 2018

By Matt Manson

Diamonds in Canada: Recent Advances in Exploration Methodology and Advanced Stage Assessment 1. Exploration Methodologies ? Prospectivity Mapping ? Surficial Geochemistry ? Geophysics 2. Advanced Stage Assessment ? Petrology and Diamond Paragenesis ? Micro/Macro ratios and Macro grades ? Value Sampling and Modeling

Apr 1, 2005

By S Sokhanvaran

Electrodeposition of silicon from a cryolite based electrolyte at a relatively low temperature (1000°C) is a promising approach to generate high purity silicon. In order to obtain fundamental data pertaining to electrowinning of silicon from Cryolite?SiO2 melts, density and electrical conductivity measurements were made. A range of temperatures and SiO2 contents was studied for each property. It was found that while density has an inverse relationship with temperature, the dependence for electrical conductivity is direct. Increasing silica content up to the saturation limit (~ 5 wt%) increases the density whereas further increase in SiO2, lowers the melt density. On the other hand, the conductivity is lower for the melts with greater SiO2 content, at any temperature.

Jan 1, 2011

By W. Beres, M. Bielawski

Recent research on the development of erosion resistant coatings has been directed to the finite element modelling of the behavior of coating and substrate, and their interface under the impact of eroding particles. The approach presented in this paper is based on advanced computer simulation techniques using ABAQUS/Explicit to investigate stress and strain at the surface and at the coating/substrate interface of multilayer coatings under single particle impact. It was found previously that solid particle erosion mechanisms are predominantly governed by the kinetic energy of the impacting particles. However, recent modelling efforts revealed that effects of various material models could be also significant. Therefore, different material models representing relevant coating and substrate properties were investigated and the effects of these models on the coating/substrate response were studied. Particularly, differences between elastic, elastic-plastic and brittle cracking model responses were assessed.

Jan 1, 2006

By Keith Jones, Largo Albert

"Decelerometer testing of a rigid guide system in a mine shaft pro vides usefuI information to operating and maintenance people. High acceleration/deceleration rates can lead to high maintenance costs to bath conveyances and shaft and can also present an operating risk . Possible disastrous results in the shaft have been avoided by restricting the maximum conveyance speed until the shaft and/ or conveyance problems have been solved.The test instrument is a valuable aid especially during commissioning or updating of a hoisting installation. High acceleration/deceleration rates also lead to reduced hoist rope life. During the past fourteen years, a total of 15,000,000 feet of testing was performed in 74 assorted shaft compartments.Based on this experience, it is possible to establish acceptable conveyance maximum speeds provided that all other conditions in the shaft compartment are normal. The body of the paper will present examples of several tests made under actual operating conditions.IntroductionMore and more mine operators are recognizing the real value in the use of the decelerometer for determining the state of shaft guide alignment in their shaft compartments , not only during the initial mine start-up periods, but also on a regular basis while the mine is in production.Decelerometer testing, is a technique in which an accelerometer , commonly known as a decelerometer, is used for measuring conveyance acceleration/deceleration in a lateral plane. lts purpose is to determine the severity of shock loads produced by misaligned shaft guides. Testing is performed by mounting the instrument on the conveyance and operating the conveyance (empty and loaded) at various speeds up to and including full speed . However, full speed may not be attained due to conditions indicated by the tests. These conditions may present an operating risk to the plant."

Jan 1, 1984

By D. B. Stewart

This paper reports on an investigation undertaken to determine the exhaust gas temperatures of operating underground mining equipment. The effectiveness of platinum catalytic purifiers is discussed. From exhaust temperatures, it is concluded that LHD engines are highly loaded, haulage truck engines are moderately loaded and utility vehicle engines are lightly loaded.

Jan 1, 1979

By X. Cao, J. J. Jonas, Wanjara. P., J. Gholipour, E. Dalgaard

The linear friction welding (LFW) behaviour of near-ß titanium alloy Ti-5Al-5V-5Mo-3Cr (Ti- 5553) was investigated. Microhardness measurements were performed in order to evaluate the mechanical properties of the welded material. The linear friction welded (LFWed) Ti-5553 was examined with optical microscopy and scanning electron microscopy (SEM) to evaluate the microstructure’s response to the thermomechanical conditions. Characterization of the welds included analysis of the microstructural features of the weld region and thermomechanically affected zone (TMAZ) in relation to the parent material.

Jan 1, 2010

By H. Craig Boyle, Craig H. B. Leitch

"The Trout Lake stockwork molybdenum deposit is located in the Selkirk Mountains of British Columbia, 50 km southeast of Revelstoke. The property is being explored by a joint venture between Newmont Exploration of Canada and Esso Minerals Canada.The deposit is associated with a small granodiorite stock of Upper Cretaceous age (76 Ma) which has variably altered the surrounding schists, argillites and marbles of the lower Paleozoic Lardeau Group to hornjelsic biotite schists and skarn. The intrusive is composed of a small stock and an intersecting network of northeast- and northwest-trending dykes at surface that coalesce downward into a larger stock. There are two main phases of intrusion, with an earlier quartz porphyritic granodiorite cut by an intra-mineral ""quartz diorite"" porphyry. A strong sub-vertical north-trending fault controls the distribution of the mineralized stock work and displays post-mineral movement.Molybdenite, accompanied by pyrite and pyrrhotite, is mainly present along the margins of veins in a well-developed quartz stock work, but occasionally is strongly disseminated in microfractured intrusives. The stock work is strongest in and around the contacts of the intrusive and its apophyses, and occurs over a vertical range of more than 1,000 m. As defined by the 0.10% MoS] contour, the main mineralized zone is up to 300 m long by 200m wide. Preliminary drill-indicated reserves, currently being revised, are approximately 50 million tonnes of 0.23% MoS2, within which are several zones of higher-grade material. Hydrothermal alteration, as defined by quantitative X-ray diffraction studies on composite core sections, is composed of a central quartz/K-feldspar/albite/minor biotite zone coincident with molybdenum mineralization, which is overlapped by a slightly later, antipathetic quartz/ sericite/pyrite zone. Ankeritic carbonate is also a common alteration mineral, but only traces of fluorite, and no topaz or sulfosalts, have been observed. Analysis for trace elements such as Sn, W, Bi, Sb, As, Hg, U, Ag, Au, Mn, Cu, Pb, Zn and F has been limited except for Sn and W, which appear to be zoned inside and outside the Mo zone respectively; the other elements do not show detectable patterns thus far."

Jan 1, 1983

By Zhan Zhang, Hiromi Nagaumi, Zhen Li

"Recently, the remarkable strengthening effect of ??-Al(Mn, Fe) Si dispersoids at both ambient temperature and elevated temperature were found by several researches. A large amount of dispersoids can be formed by applying special heat treatments and within a suitable range of chemical composition of AA3xxx alloys. In the present work, the influences of Cr addition on the mechanical properties and microstructures of the Al-Mn-Mg-Si alloys were investigated. The mechanical properties at ambient and elevated temperatures were evaluated by micro-hardness and yield strength. Moreover, the microstructures in as-cast and heat-treated conditions were quantitatively analyzed by optical and electron microscopes. Results revealed that Cr also had effect on the number density and volume fraction of dispersoids. Micro-hardness and yield strength at ambient temperature increased with the increasing content of Cr, and the Cr addition increased the yield strength at elevated temperature as well. Moreover, the creep resistance at 300°C improved dramatically with the increasing content of Cr.INTRODUCTION Traditionally, AA3xxx aluminum alloys were widely used in packaging, automobile and architecture industries, because of its good formability, excellent corrosion resistance and weldability. And AA3xxx alloys were considered as non-heat-treatable alloys. However, the strengthening effect of dispersoids in AA3xxx alloys was discovered recently (Li & Arnberg, 2003;Li, Muggerud, Olsen, & Furu, 2012; Li, Zhang, & Chen, 2016; Liu & Chen, 2015).Alarge amount of dispersoids could precipitate by a proper heat treatment.In order to further improve AA3xxxalloys, the composition of the alloys should be optimized. A few previous studies were reported to investigate the influence of compositions on AA3xxx alloys. Adding Mn element could enhance the precipitation of ??-Al(Mn, Fe)Si dispersoids and improve the yield strength(Muggerud, Mørtsell, Li, & Holmestad, 2013), as long as the concentration of Mn was under the solid solution limit. Fe decreased the solubility of Mn and accelerated the precipitation rate of ??-Al(Mn, Fe)Sidispersoids(Li & Arnberg, 2003), the yield strength and creep resistance at elevated temperature could increase with an optimized content of Fe(Liu & Chen, 2016). Mg element would affect the nucleation process of ??-Al(Mn, Fe)Sidispersoids by forming metastable Mg2Si(Hirasawa, 1975; Li, Zhang, & Chen, 2017a; Lodgaard & Ryum, 2000), metastable Mg2Si precipitated during heating process and promoted the precipitation of ??-Al(Mn, Fe)Sidispersoids, moreover, Mg provided solid solution strength for AA3004 alloys(Li et al., 2016). Si increased the volume fractionof ??-Al(Mn, Fe)Sidispersoids(Muggerud et al., 2013)and decreased the size of ??-Al(Mn, Fe)Sidispersoids(Li, Zhang, & Chen, 2017b). With the addition of Mo, the size of dispersoids became finer with a higher volume fraction, the volume percentage of dispersoid free zones was reduced. Elevated temperature yield strength and creep resistance improved due to Mo addition (Liu, Ma, & Chen, 2017).However, the effect of Crelements on microstructure and mechanical properties of AA3xxx alloys were rarely reported."

Jan 1, 2018

By Mohammad Reza Khalesi, Ruhollah Rezazadeh, Mohsen Izadi Yazdan Abadi, Mahmoud Abdollahy

"The rotary vacuum drum filter (RVDF) is widely used for dewatering in mining industrial. In general, different parameters have influence in the solid-liquid separation such as: solid percent, level of vacuum, particle size distribution, filter cloth and chemical additives. These parameters can influence on some variables such as cake moisture, throughput and filter cloth life time. The aim of this study is to propose some chemical additives to improve the rate of filtration and decrease cake moisture of Gol-E Gohar iron ore concentrate by using laboratory scale bottom feed vacuum filter and suggest a filter cloth with long life time (more than 400 hours). Effect of particle size distribution on filtration investigated in large scale by measuring the thickness of cake and cake moisture.Increasing molecular weight of anionic flocculant lead to increases throughput but cake moisture increases too; While the filter aid increases throughput and decreases cake moisture simultaneously; the combination of them show different behavior. TSS and filter cloth life time have directly relation with material and type of filter cloth weave. Depending to type of feed, two polyester and polypropylene filter cloth are suggested. More over twill and satin weave have the best results. To prove the laboratory results some industrial tests performed in Gol-E Gohar hematite iron ore concentrate plant.INTRODUCTION“The process of grinding and classification involves the use of large quantities of water. The separation of solids from liquids is usually achieved by gravity sedimentation in thickeners. For fine particles this is a slow process. In general, 75–80% of the water can be separated and removed by thickeners. For further water removal, filters are used where in excess of 90% of the water can be removed” (Gupta, 2006).“Many types of filters are available, which are broadly classified here as vacuum, pressure, precoat and depth filters. Each classification contains a number of sub-processes. A category of filter that uses vacuum induced driving forces and semipermeable media to facilitate the separation of solids from suspension. While pressure differences across the filter are limited to less than 85 KPa (usually 75 KPa), most units are capable of processing a wide range of feed materials in a continuous manner” (Rushton, 2008)."

Jan 1, 2016

By Akihiko Nishiyama

Unmanned construction technology used for remote control operation of construction machines has some problems to solve compared with manned operation of construction machines, such as fatigue due to long-term operation or decreases in operational efficiency. To solve these problems, we recorded the viewpoints of operators in both manned and remote control operation and analyzed the differences. This paper reports on our discussion of improving the operability of remote control operation based on the analysis results.

Aug 1, 2013

By E. De Souza

Energy associated with ventilating an underground operation comprises a significant portion of a mine operation's base energy demand and is consequently responsible for a large percentage of the total operating costs. Ventilation systems may account from 25?40% of the total energy costs and 40?50% of the energy consumption of a mine operation. Fans are the most important mechanical devices used to ventilate underground mines and the total fan power installed in a single mine operation can easily exceed 10,000 kW. Investigations of a number of mine main fan installations have determined their assemblage to be, in general, very energy inefficient. The author has found that 40?80% of the energy consumed by a main fan is used to overcome the resistance of fan assemblage components. This paper presents how engineering design principles can be applied to improve the performance and efficiency of fan installations, resulting in substantial reductions in power consumption, operating cost and greenhouse gas emissions. A detailed case study is presented to demonstrate that, by designing fan assemblages using proper engineering concepts of fluid physics and industrial ventilation design, main fan systems will operate at efficiencies well above 80?90% (compared to common operating efficiencies of between 20 and 65%), resulting in a drastic reduction in a mine's overall costs and base electrical and energy loads.

Aug 1, 2013

By J. Shahabpour

"Abstract - Breccias with angular and rounded clasts of a late-mineralization, ""barren"" hornblende porphyry dike set within a comminuted matrix consisting of rock fragments and quartz, cemented by quartz and K-feldspar of hydrothermal origin is observed in diamond drill cores from the Sar Cheshmeh porphyry copper deposit. Studies of age relationship between vein types, phyllic-altered clasts and the breccia groundmass suggest that the brecciation is a late event. The breccia clasts record evidence of hydrothermal reaction between the clasts and fluids responsible for the brecciation.Formation of bornite, in the breccia clasts of the originally barren hornblende porphyry dike, and in the breccia matrix, along with the scarcity of bornite in the Sar Cheshmeh deposit itself suggest involvement of fluids which are later and of different composition from the fluids responsible for the known mineralization at Sar Cheshmeh. These later fluids may be related to a later plutonic event and suggest the possibility of a later, and concealed deposit."

Jan 1, 1994

By H. A. Kramer

The Flin Flon mine is at present hoisting 5,000 tons of ore daily. In 1943, a peak production of 6,188 tons daily was maintained. Before discussing secondary blasting, it is felt that a short review of stoping procedure will be of value. A list of papers dealing with various phases of the mining operation is appended. Stoping Practice Stopes vary in width from 30 to 150 feet, in length from 200 to 450 feet, and in height from 200 to 500 feet. A typical stope would be 300 feet long, 300 feet high, and 90 feet wide. The dip of the orebodies varies from 60° to vertical, with an average of 82°. The ore is heavy, having a specific gravity of 4. Both sub-level benching and radial drilling are practised. Blast-hole diamond drills are responsible for 85 per cent of the total production. Two sizes of hole are drilled at present, 11 7 6 -inch and 1%-inch. For bench drilling, the burden on the 1 7/16-inch hole is six feet, with holes on 8-foot staggered centres; in radial drilling, the burden is six feet, with nine feet between the toes. The burden on the l 5/8-inch hole is eight feet with holes on 11-foot centres, or 13 feet on the toe of fanned holes. Holes are blasted with two No. 8 instantaneous electric caps per hole, using 403 Polar Forcite. A powder charge of 0.15 pounds per ton is used, with a tonnage factor of 5 and 6.4 per foot drilled for the two sizes. Two rows of holes are blasted together. Fragmentation is satisfactory with the above drilling pattern and powder charge. However, some overbreak and fall-off locally results in oversize material. It is estimated that, after primary breaking, 75 per cent of the ore will pass through the grizzly openings and 15 per cent will pass the draw points, leaving 10 per cent that must be broken further to pass the draw points.

Jan 1, 1946

By Roméo Roussin

"The yearly production from the Asbestos Hill pit is 1,550,000 tons of asbestos ore, with a yield varying between 18 and 20 % . The orebody was exposed at the top of a hill, and initial production started without having to remove any overburden. The projected ratio of barren rock to ore, based on the present orebody, was 2 to 1. However, as it was necessary to push back the upper benches, this ratio has changed to 3 to 1. The final pit will be 2,300 feet long by 1,000 feet at the longest and widest points. The final depth will be 680 ft. A pit slope stability study was carried out and an average wall angle of 60-70 degrees must be maintained. Preshearing of final pit limits will produce good wall stability. Permanent access ramps will be 60 ft wide, with an 8 % maximum grade. Geological conditions and the low rock temperature are the major causes of the operation's drilling and blasting problems."

Jan 1, 1976

By W. Holdsworth

The flotation mill of Dentonia Mines, Limited, at Greenwood, B.C., went into operation on April 20th, 1934, and by October 11th a total of 15,000 tons of ore had been treated. It is intended in this paper to describe briefly the operation and to give some of the operating data which have been gathered. The metallic minerals in the Dentonia ore are pyrite, chalcopyrite, galena, and, occasionally, native gold, and the gangue includes chloritic material, vein quartz, and calcite. Pyrite makes up about 90 per cent of the metallic content of the ore, in which it is disseminated as irregular grains and well-formed cubes. An average analysis of the ore is: gold, 0.27 oz. per ton; silver, 1.73 oz. per ton; copper, 0.12 per cent; lead, 0.31 per cent; and zinc, trace. From the mine ore-bin, situated near the portal of the tunnel at the mine, the ore is hauled by motor truck to the mill, a distance of three-quarters of a mile, and there dumped into the receiving bin, which has a capacity of fifty tons. The hauling is done during one eight-hour shift, commencing at 7 a.m. The maximum size of the ore fed to the mill-bin is ten inches. Lumps larger than this are broken by sledge hammer to pass through grizzly bars, spaced ten inches apart, installed above the bin. The ore is drawn from the bin by a 30-inch, 6-ply conveyor belt, 18 feet 6 inches long. In the near future, when the cross-cut tunnel is completed, the ore will be trammed to the receiving bin. This will effect a considerable saving in cost. At the same time, the bin will be set back several feet, so that the length of the conveyor belt may be doubled. This will make efficient ore-sorting possible, and so ensure a minimum of waste rock in the mill feed.

Jan 1, 1935

By S. Bozorgi, K. Anders

"The automotive applications of heat treatable AlCu cast alloys are designed for performance at high temperature, which can be improved using specially alloying element as well as different heat treatment. In this research work an effect of alloying element such as Cu, Ni and heat treatment on microstructures and mechanical properties of AlCu alloy were investigated using optical microscope (LIMI), scanning electronic microscope (SEM) equipped with energy dispersive X-ray detection (EDS), Differential scanning calorimetry (DSC) and mechanical testing. It was found that during solidification most of the elements Cu, Mg and Ni segregated at the grain boundaries in the form of Al2CuMg or Al7Cu4Ni and a very small part of Cu and Ni element dissolved in the FCC-Al matrix. The latter is not completely reclaimable for strengthening mechanisms in FCC-Al matrix in its as-cast state. The results of mechanical test show that yield strength and ultimate tensile strength increases after heat treatment significantly compared with the as-cast state. Furthermore the mechanical properties at elevates temperature (240°C) is higher with higher Cu+Ni+Si containing alloys compared with the less Cu+Ni+Si containing alloy.INTRODUCTION Due to the high strength-to-weight ratio, high strength and ductility at room- and elevated temperature, AlCuSi cast alloys are widely applied in the automotive industries specially for producing cylinder head and engine block, where modified alloys with enhanced metallurgical properties are always needed to satisfy the ever increasing demands for the applications. The AlCu based cast alloys can be strengthened by age hardening. The precipitation processes from which this hardening is derived can be attributed to the presence of selected trace element additions or micro alloying, which can change the process or kinetics of precipitation in age hardenable AlCu cast alloys (Polmear, 1998; Morris, 1991). Furthermore their strength is mainly controlled by the aging process through the precipitation and growth of very fine precipitates of the ?'-phase (a semi-coherent, metastable form of the equilibrium Al2Cu phase) from the Al and Cu Guinier-Preston (GP) zones. Several studies have shown that solute clustering occurs prior to the precipitation of GP zones, and this modifies both the nature and kinetics of the precipitation process. The typical size of GP zones is in the order of tens of nanometers, and the chemical composition of these precipitates is not easily measured, even with a typically analytical electron microscope (Polmear, 1989)."

Jan 1, 2018

By C. D. M. Chisholm

IN discussing stope filling, or backfilling, at the Sullivan mine, at Kimberley, B.C., a brief description of the problem will first be presented. The Sullivan orebody is a replacement in quartzite, with the ore con-forming, for the most part, with the bedding. The dip of the vein, apart from local irregularities, averages about 15 degrees near the outcrop in the southwest section of the mine, and steepens to almost 40 degrees at the northeast end of the mine. The thickness varies from a few feet to over 200 feet at the widest sections. The mineable length along the strike has averaged about 4,000 feet between the 4,600 and 3,900 levels-the section under discussion in this paper. To date, 28,000,000 tons of ore have been mined by the room-and-pillar method. Prior to 1930, all ground opened up had been supported by ore pillars, left during mining operations. From that time, the recovery of the ore from these pillars has been given serious consideration. Backfilling, as being carried on today, is the result of this study and is being done for two reasons: (1) to allow extraction of the ore pillars, and (2) to minimize subsidence of the hanging-wall rock, except where forced caving is found desirable. PRELIMINARY DEVELOPMENTS LEADING TO BACKFILLING When the Sullivan orebody was first opened up, early in the century, there appeared to be low-grade sections of the vein sufficient in extent to serve as permanent support for the roof. However, as mining extended into sections of the vein that showed continuous ore over greater areas, wooden cribs, filled with waste and low-grade ore, were erected. In some stopes, these cribs were as large as 40 ft. by 100 ft. in plan and from 50 ft. to 60 ft. in height, but it was soon realized that this method of support was inadequate. As mining progressed, it was found necessary to leave ore pillars, which eventually became the sole system of support. At first, these pillars were left at irregular intervals, but later they were laid out at definite locations on the mine plans, and these locations were adhered to as closely as mining would permit.

Jan 1, 1941