Search Documents

By Y. G. Yaroshenko, V. Y. Baldin, Y. M. Gordon

The manufacture of sulphuric acid from the off-gas of pyrometallurgical processes in the production of heavy metals is one of the common methods of effective recycling of sulfuric anhydrite. The new Impact-Inertial Devices with the rectangular contact channels (IIRCh) and the internal circulation of liquid allow the injection of an absorber into the phase's interactive cell by utilizing the gas stream energy and by this way increasing the sulphuric acid yield and reducing the power consumption. These devices have the following advantages: simplicity of design, smaller size, low capital expenses, absence of irrigating system, high operational reliability, simultaneous cleaning of solid, gaseous and liquid impurities and also cooling of gases etc. The IIRCh efficiency is almost 18 % higher and they require 1.3-2 times lower energy when compared with Venturi Absorbers. Also the elevation of spraying nozzles or injectors is 1.5 times lower in the IIRCh case.

Jan 1, 2004

By H. C. M. Gordon

IT is essential to the success of any mining op::ration that the roadways through which the material wrought and ocher materials and supplies are to be transported should be kept in such condition that this transportation cart be effected rapidly and without difficulty. The longer the roadway and the greater the tonnage to be taken over it, the more necessary it becomes chat the construction and maintenance of the road be such chat traffic delays can be reduced co a minimum. le is proposed co deal with the development and construction of roadways serving longwall operations and, since a recreating system of longwall is worked, as a rule, only where roadways driven in the solid coal can be readily maintained, the discussion will be confined co advancing longwall roads which are driven through areas from which the coal seam has been totally extracted. In order to construct a roadway through extracted ground in such a manner that it will remain in a state of reasonably good repair without undue maintenance, it is necessary chat everything possible be done to bring the overlying strata co a state of equilibrium as quickly as this can be effected, and the operations should be so planned that future workings will not disturb the equilibrium so set up more than can be avoided. Obviously, the readiest way to obtain a stable roadway is to develop it by tunnelling through a settled waste. However, this cannot always be done, as some of the roadways must be developed and constructed as the walls progress, but level or lateral cut-offs can be constructed in this manner. Main-slope roads can be developed in a similar manner after the coal has been extracted and a waste formed for at !east five hundred feet on either side of the line of the permanent roadway from temporary subsidiary roads developed for this purpose along one or other of the flanks of the waste to be formed. This interval must be obtained in order chat the lacer extraction of the seam will not set up movements in the waste immediately overlying or adjacent to the constructed roadway, thus upsetting the equilibrium of the strata and distorting the road.

Jan 1, 1940

By Luino Jr. Dell'osso, Richard L. Every

The enormity of the methane-in-coal problem is discussed, with a brief summary of the state-of-the-art. Laboratory techniques and data on the desorption of methane from Pittsburgh seam coal are presented and discussed and include the effect of time, temperature and vacuum. Under laboratory conditions, it was possible to displace 90 per cent of the residual methane by flooding the coal samples with carbon dioxide. Carbon dioxide was found to be three times more effective than air and almost five times more effective than helium.

Jan 1, 1972

By Tim Watson

Andacollo Hypogene Project ?Overview Project description: Sulphide copper concentrator Throughput:55,000 tpd Location: Approximately 50 km from La Serena Elevation: Approximately 1,000 m ASL Start feasibility study: July 2005 Start of construction: May 2007 Construction completion: December 2009 Final cost(1,2,3):435 Million US $ (1) Excludes third party costs, 220 kV power line (2) Cost is based on a Chilean Peso to US Dollar foreign exchange rate of 535 to 1 (3) Does not include US$40.3 million for the Elqui River Pipeline Project or US$8.0 million for the stock pile cover

May 1, 2010

By A. Koning, P. Lauzon

Pressure hydrometallurgy operations require vessels to be lined with an impermeable membrane for corrosion protection and one or more courses of refractory or ceramic brick. Examples of unit operations that utilize composite lining systems include pressure oxidation autoclaves, sulphide precipitation autoclaves, chloride leach reactors, flash vessels, cyclone separators, and direct contact condensers (heater vessels and quench vessels). The refractory lining must satisfy multiple requirements: it must thermally insulate the membrane from process fluid, be structurally stable, provide erosion resistance, be chemically compatible with process fluid, and provide an economic service life. New hydrometallurgical processes are pushing the pressure, and temperature, with each new generation of plants. A fundamental understanding of all factors affecting the mechanical stability of the lining system is essential as lining designs move further away from the industry's experience base. The impact of irreversible chemical swell, operating factors, design factors, and installation factors are presented based on modifications to the traditional one-dimensional mechanical stress model. A new stability criterion - that the brick lining remain in contact with the steel shell membrane - is presented. This new stability criterion imposes new restrictions on the lining design.The effect of geometry and adding additional degrees of freedom to the analysis is explored using two-dimensional and three-dimensional Finite Element Analysis (FEA). The effect of these additional degrees of freedom on the results of the one-dimensional model are discussed.

Jan 1, 2004

By S. Perez

Core drilling is a fundamental process in the mineral exploration industry. As deep exploration in hard rocks is accelerated due to the depletion of near ground mineral resources, deep-drilling operations need to reduce their reliance in operators experience and begin to implement new technologies in order to increase efficiency and cost-effectiveness of the overall process. Currently, lack of real-time information on the bit/rock interaction is a major problem. Therefore the mechanism behind the acoustic emission, which is a proven technique for remote monitoring, generation in mechanical rock cutting must be understood in order to provide real time information about the rock. This paper aims to identify the influence of mineral composition of granitic rocks on the acoustic emission (AE) during rock abrasivity test with a single contact tool and to evaluate the feasibility of AE as a means to infer Cerchar Abrasivity Index (CAI). Single contact tool will provide precise and accurate description of the source of AE. To provide constant grooving speed Cerchar apparatus was modified to monitor AE during rock/tool interaction. Tests on the modified Cerchar apparatus are carried out under the static load of 70N and cutting speed of 1 mm/s. A Scanning Electron Microscope (SEM) is utilized to visualize the groove in the rock and to identify the mineral composition through Back-Scattered Electrons (BSE) reflected from the rock sample. Based on the microscope images, it was found that biotite shows a larger groove area and plate-like fractures accompanied with burst-type AE signal, whereas plagioclase and quartz, which are characterized by similar hardness and BSE brightness, possess shattered-like fractures and more continuous-type AE signals. In addition, a-value of the Gutenberg-Richter scale has been found to well correlate with Cerchar Abrasivity Index (CAI).

Jan 1, 2015

By Seher Ata

"Virtual reality, a three-dimensional computer generated environment, has become recognized delivery system for many forms of education. This article describes the application of virtual reality to mineral processing education. An interactive mineral processing visualisation module has been developed at University of New South Wales (UNSW), Australia. The module provides students with an overview of a base metal concentrator, details about each stage of the process, as well as revealing how the mined ore progresses from stage to stage. The module also involves developing a number of instructional based plant layouts and flowsheets in the virtual environment that are intended to assist the user in understanding the essential components of the base metal concentrator.INTRODUCTIONVirtual Reality (VR) is the creation of an artificial environment that is experienced through sights and sounds provided by a computer (Squelch, 2001). The simulated environment is achieved through a host of technologies such as three-dimensional graphics, audio feedback and special peripheral devices to produce interactive environments.VR has been used in diverse fields including medicine (Riener & Harders, 2012), entertainment (Hsu, 2011), military (Manojlovich, Prasithsangaree, Hughes, Chen, & Lewis, 2003), manufacturing (Zimmermann, 2008; Jiang, 2011), and chemical processing (Schofield, Lester, & Wilson 2005; Squires, Andersen, Reklaitis, Jayakumar, & Carmichael, 2014). VR is also becoming recognized delivery system for many forms of education, including engineering education (Bell & Fogler, 1996; Bell & Scott, 1998; Shin, 2002). For example, virtual laboratories have been designed and developed to teach students fundemental features of the heterogeneous catalytic mechanisms and absorption columns (Bell & Fogler, 1995), the multi-phase and multi-component blast furnace iron making process (Babich & Senk, 2009) and to guide students to identify various safety measures while working in real laboratory (Bell & Fogler, 1996)."

Jan 1, 2016

Roasting of molybdenite concentrate is an important stage in the production of commercial molybdenum trioxide. The oxidation kinetic and mechanism of molybdenum sulfide concentrates from two plants were investigated at temperatures from 444 °C to 640°C. The rate of reaction was determined for thin layer samples in a muffle furnace at controlled temperatures, oxygen excess and removal of sulfur dioxide. For both concentrates the rate of reaction is fairly slow at temperatures below 500°C and remains fairly constant from 540 to 600 °C. It was observed that the concentrate from the first plant presents a tendency for sintering or glazing at temperatures above 620°C, whereas the same phenomena was observed at 20 or 30 °C higher temperature for the second concentrate. A kinetic model of two reactions, involving the formation of Mo02 as intermediate oxide for the production of Mo03 is proposed and activation energies of 23.0 and 20.8 kJ/mol for the first and second reaction were calculated for temperatures between 520 °C to 600 °C. These low values of activation energies indicate that the overall rate of oxidation is controlled by mass transfer, particularly in a porous layer of oxides. Therefore, the renewal of the surface by mixing and motion of the concentrate layer is of great importance. Sublimation of Mo03 becomes significant for temperatures above 650 °C.

Jan 1, 2007

By Richard S. Allen

"The casual visitor is not apt to think of the Adirondacks as a one-time hive of mining and manufacturing activity. However, where there are mountains there are usually minerals and northern New York State is no exception.The Adirondacks are a rocky shield, a great stone cap pulled down over what is now northern New York. The bedrock consists of layered metamorphic rocks which were once sandstones or limestones on the bottom of a shallow sea that covered the region 1000 million years ago. The highlands are composed for the most part of the igneous rock anorthosite. Ancient earth upheavals at temperatures of at least 750°C mixed molten masses of anorthosite and the minerals it contained with the older metamorphic rock, resulting in deposits of iron-titanium oxide s, red garnet and other valuable minerals. Of these, the most readily recognizable was iron.The first hint of the existence of iron ore in the Adirondack Lake Champlain region of upper New York State seems to have come from a Swedish naturalist, Peter Kalm (1716-1769), who travelled through French Canada and visited the military outpost of Fort St. Frederic in 1749. In July of that year, Kalm wrote:""Among the kinds of sand which are found on the shores of Lake Champlain; one is black and the other garnet-colored... and they sparkle when the sun shines. All the grains of this sand without exception are attracted to the magnet, the uppermost or black sand being about a quarter inch deep...""Concerned primarily with the fur trade, the officers and men who occupied this remote bastion of La Belle France were apparently unaware of the industrial and commercial possibilities beneath their feet. No deposit of iron was then known to exist any closer than the Three River s area in Lower Canada."

Jan 1, 1983

By William G. Pariseau

"This contribution describes linkage of stress concentration at the face of tabular excavations, for example, longwall coal mine panels, at a meter scale to surface subsidence at a kilometer scale. Joints are considered according to orientation and spacing at an intermediate scale. A new dual-node, dual-mesh technique based on first principles uses a multi-scale technique that allows for computing whole mine surface subsidence while also allowing for computational details of stress, strain and displacement about main entries and pillars, panel entries, and bleeder entries. The technique is implemented in a conventional continuous Galerkin finite element program that has been in use for many years.The advantage of the dual-node, dual-mesh technique is the capability to do a whole mine analysis that takes into account interaction between all sections of a mine where stress transfer over long distances is often the rule rather than the exception while at the same time allowing for details of stress concentration at working faces where caving is initiated and subsidence begins. The technique, outlined recently during ARMA 2014 (Pariseau, 2014), is applied to an underground coal mine in central Utah where mines are developed from outcrops in steep canyon walls. Meshes contain over 10 million, three-dimensional nodes; runtimes are typically overnight, as a practical matter. Results compare favorably with mine subsidence measurements made over a period of several years and show the capability of this new technique to provide useful design guidance for tabular deposits such as underground coal mines. The role of variability or uncertainty in strata properties is illustrated in element safety factor distributions about development, bleeder and main entries and pillars. Such details are new in this contribution. Energy tracking for mine-induced seismicity is also new. Results show a high correlation between number of events and failed elements and suggest a simple index to mine induced seismicity."

Jan 1, 2015

By Karl J. C. Harries

"1.1. WHAT ARE AGREEMENTS AND HOW ARE THEY FORMED?In order to have an agreement, at common law, there must be an offer, acceptance of that offer, and consideration passing between the parties. In addition, the material terms (i.e. the basics or substance) of the agreement must be discernible, preferably by means of documentation. Although these concepts may appear simple and straightforward, the law relating to them is voluminous and complex. Some brief comments are worthwhile.• Offer/acceptance: Both offer and acceptance should be in writing, but they need not be. The actions, conversations, and/or correspondence of the parties may constitute either or both of them. Notwithstanding, the local law or practice of a jurisdiction will impose some specific requirements for certain types of agreements. If these requirements are not met, the agreement may be unenforceable. For example, Ontario’s Mining Act requires transfers of unpatented mining claims to be evidenced in writing and recorded.1• Consideration: Consideration is usually thought of as being money, but it can be virtually anything, even “the premises” (i.e. the mutual covenants or promises contained in the agreement itself). In addition, if one party, relying upon the offer of another, does something to his detriment, then the doing of the act can be considered to be an acceptance of the offer and, under the legal concept of “detrimental reliance”, can also be consideration. Whether or not detrimental reliance exists will depend upon the circumstances of each case.2• Material terms: The requirement that the material terms of an agreement must be discernible does not mean that all of the terms of an agreement must be documented or even have been considered, just the basic or material ones. In addition, it will be up to a judge to decide what is material – not necessarily the parties. In order to establish the material terms, a Court may look at all relevant documentation and may hear oral evidence. It will resist “writing the agreement”"

Jan 1, 2003

By F. Rashchi, N. Naseri Joda

Recycling of electronic wastes is an important subject both from an environmental point of view and also the recovery of valuable materials. In this research, PC board scraps were leached to recover Cu, Ag, Au and Pd. Due to the high cost of the shredding process and to avoid secondary pollution from odors and dusts, board scraps were cut into 5X5 cm2 pieces. To determine the most effective leachant, aqua regia, nitric acid, hydrochloric acid, ammonium persulfate and potassium persulfate were tested. The effect of the leaching parameters, the leachant concentration, temperature, leaching time and liquid to solid ratio were studied and optimized using response surface methodology.

Jan 1, 2011

By Harry J. Cain

Introduction The property of Pioneer Gold Mines of B. C., Limited, is located in the Lillooet mining district of British Columbia, on Cadwallader creek, 54 miles distant by motor road from Shalalth, a station on the Pacific Great Eastern railway. Milling by the present Company was commenced in 1924, a small amalgamation plant, consisting of a crusher, Bryan mill, and plates being operated until 1928. Tailing from this plant was impounded and later treated in the 100-ton continuous counter-current decantation cyanide plant which was erected during 1927-28 and placed in operation during May of 1928. A second cyanide plant, employing continuous counter-current decantation, having a nominal capacity of 200 tons, has been erected during the past few months and was put into operation during September of the present year. The ultimate capacity of the combined units of the present mill has not been determined, but it is expected to be much in excess of the rated capacity. The Ore The ore, as received at the mill, consists chiefly of quartz carrying free gold, with small amounts of pyrite, arsenopyrite, and pyrrhotite in evidence, though probably amounting to less than one per cent of the total. Some gold is very closely associated with the sulphides. The country rock is a basic igneous rock, probably an augite diorite. Near the vein it is highly altered to sericite, which slimes readily on grinding, and does not settle very well. The quartz is of two types, clear and ribbon. In the latter, the ribbons, which are not much thicker than paper, consist of shattered sulphides. In crushing this ribbon quartz, breakage is often along the streaks, exposing these shattered faces to advantage in subsequent treatment. While gold is the metal for which the ore is mined, some silver is also present and is paid for by the mint. It is, however, unimportant from a commercial viewpoint. From the standpoint of crushing and grinding, the ore might be termed 'medium 'hard'.

Jan 1, 1932

By E. A. Roux

As the first mine-to-metal zinc operation utilising atmospheric leaching, solvent extraction and electrowinning, Skorpion Zinc faces unique challenges and opportunities. One of these challenges is found in the solvent extraction circuit, in which di-ethylhexyl phosphoric acid (D2EHPA) is used as the organic extractant. Although D2EHPA is an excellent extractant for zinc, it suffers from the co-extraction of ferric iron, which is produced during leaching and by the corrosion of the grinding media. This situation is partially mitigated by iron precipitation in the neutralisation step prior to solvent extraction. Unfortunately, some ferric iron still reports to the solvent extraction process. This leads to a slow build up of iron in the organic phase. Chemical stripping is used to maintain the Fe concentration at an acceptable level. In this paper, the efficiency of the iron removal process is discussed.

Jan 1, 2006

By F. Parada, R. Parra

"The neutralization process of SO2 from coal burning plants is a well-defined technology using limestone to form CaSO4 according to the following reaction: CaCO3 + SO2(g) + 1/2O2(g) = CaSO4 This paper presents the results of a study carried out to validate the option of capturing SO2 using gases from a non-ferrous smelter; SO2 content was up to 12% using a three-stage fluidized bed reactor. The difference in SO2 content affects equilibrium conditions and kinetics, rendering a direct extrapolation of the high efficiency achieved for low SO2 content impossible. The R&D program consisted of a laboratory study using a semi-pilot operation of a one-stage fluidized bed reactor and the construction and operation of a three-step reactor prototype. Results show that the reaction proceeds according to the unreacted core model that imposes a compromise between CaCO3 conversion and SO2 capture. For high SO2 capture, the calcine from the reactor contained CaSO4 and CaO. A complete capture of SO2 from gases with 8 vol.% can be achieved with a mean reaction time of two hours at 800°C."

Jan 1, 2007

By G. M. Behrend

"AbstractMeasurement and control systems in minerals processing plants are usually well thought out and designed. The criteria and design parameters have been interpreted correctly.However, these systems often fail to perform satisfactorily or break down altogether as a result of in-plant conditions which are unpredictable and over which the instrument systems designer has no direct control. The foresight necessary to anticipate the problems and allow for them in the systems design can only be generated by experience.This paper lists the most common of these problems and offers practical methods for their solution. It then follows with an analysis of instrument installation practices and comments on special points that need watching.Finally, instrument maintenance is discussed with a view to achieving good maintenance at the best possible economy.Good MeasurementGeneralTHE MINES and mineral processing plants of the nineteen seventies, after decades of sensible caution, have now committed themselves to extensive automatic control. X-ray analyzers are freely specified. Sample acquisition systems are efficient and automated, computers are reliable and relatively cheap, and computer control systems in conjunction with the new analyzers are operating in a good many plants and are proving to be profitable.The sight of shift foremen and floor operators assembled in front of a TV-tube and taking a computer data display as gospel truth is quite common now, and yet was quite unthinkable only ten years ago."

Jan 1, 1977

By N. J. Contini, R. W. Knopp

"In March 1988, old Denver flotation cells were removed from Dickenson's Arthur w. White Mill, and a new flotation circuit, consisting of four Prochem rougher cells and a Hydrochem agitated cleaner column, was commissioned. The refractory portion of the gold in the ore is associated with arsenopyrite, therefore the flotation circuit is set up to produce a saleable sulphide concentrate. Tailings from the leach circuit are conditioned prior to being pumped as feed to the flotation circuit. The prototype Hydrochem agitated column has been in operation as a single cleaner stage for rougher concentrate. The effect of flotation circuit changes on gold recovery data, as well as cleaner concentrate production, and development work to achieve the target results, have been investigated. Flowsheet modifications and the resulting circuit performance data, along with test results to date, will be presented.INTRODUCTIONThe mill is capable of treating 1000 stpd of ore averaging approximately 0.30 oz/ton Au. The ore is crushed and ground to 75% - 200 mesh. Gravity concentration, cyanidation, and Merrill - Crowe precipitation yields 84% gold recovery. Detailed descriptions of the comminution, gravity separation, and leaching circuits, as well as background information have been presented elsewhere (Suttill, Van Weert et al). The target cleaner concentrate grade is 1.0 oz/ton Au for custom smelting and refining. Historical gold recovery values of the old circuit was approximately 20% of the gold present in the float feed at the target grade. The recovery value objective set for the new circuit during the planning stages was 50% of the gold present in the flotation feed at 1.0 oz/ton Au in cleaner concentrate."

Jan 1, 1989

By V. I. Ryaboy, S. A. Kondratyev

"The paper describes influence of desorbed species (DS) of a number of xanthates and higher dialkyldithiophosphates on the collective ability of these reagents. Adsorbed on mineral DS of the reagents in the form of products of non-stoichiometric interaction between xanthates and heavy metal salts can pass to the gas–liquid interface and remove liquid from the layer between mineral particle and water surface. A high-speed video recording displays the process of spreading of DS of xanthates and dialkyldithiophosphates over water at the moment of local rupture of the water layer. Expansion of “dry” spot on the mineral surface after DS of xanthate capture and displace liquid from the layer has been proved with video images. The comparative analysis of collecting ability and dynamic surface activity of dialkyldithiophosphates shows that these characteristics are in good correlation. The forces exerted by spreading film of the reagent’s DS on liquid in the water layer are evaluated, and the water flow rate from the layer is determined. The line of the reduction in thickness of the water layer behind the front of spreading film of DS of dialkyldithiophosphates and xanthates coincides with the line of the increase in their dynamic surface activity. Their force on the liquid volume in the water layer characterizes collecting ability of the DS film of xanthates and dialkyldithiophosphates. It has been supposed that the collecting ability of DS of a reagent is a part of its overall flotation activity, conditioned by surface tension of solution and, thus, defined by the structure of hydrocarbon fragment of the reagent.INTRODUCTIONIt is believed that collecting ability and selectivity of collecting reagents is mainly governed by adsorption of a reagent at the solid–liquid interface. A few studies have shown that activity of collecting reagents at the gas–liquid interface may have deep influence on their collecting capacity and selectivity. Experimental researches have revealed correlation between surface pressure in a carboxylic acid film on liquid’s free surface and floatability of useful components (Kulkarni & Somasundaran, 1975; 1980; Quast, 2006). According to Quast (2006), it is not always that surface pressure of a reagent film influences collecting ability of carboxylic acid. For instance, pH range of adsorption of tetradecanoic acid on hematite does not coincide with pH range of high surface pressure. So, surface properties of this acid contribute little to flotation efficiency.The correlation between reagent film surface pressure and mineral floatability has been reveled for quartz and cationic reagents, too (Bleier, Goddard, & Kulkarni, 1977). Finch & Smith (1973) showed that combination of adsorption of ion–molecular amine complexes on mineral surface and high surface tension of “fresh bubbles” was favorable for flotation performance. The use of bubbles with reduced surface tension resulted in a decrease in quartz floatability."

Jan 1, 2016

By D. H. Flather, J. W. Hendry, K. Drover

Black Hawk Mining Inc. has completed a comprehensive program on the prediction and management of acid rock drainage (ARD) at their Keystone Gold Mine (Keystone) near Lynn Lake, Manitoba. The program, initiated in 1994, followed a phased approach utilizing initial acid-base accounting (ABA) results and subsequent laboratory kinetic testwork to define site-specific sulphide oxidation and neutralization consumption rates in waste rock. Net acid generating waste rock at Keystone was defined through the kinetic testwork as waste rock yielding a net potential ratio (NPR) of less than two. A preliminary waste rock management program based on blending of potentially acid generating and acid neutralizing waste rock was advanced. Subsequent refinement of the management program followed the analysis of over 1580 ABA samples collected from individual blast holes during the initial bench development phase of the Keystone pit. Uncertainties in actually achieving adequate blending within the dumps at a mining- scale resulted in the development of a revised waste rock management program based on segregation. Recognizing that any successful management plan requires that the ARD characteristics of the waste rock be identified prior to in-pit blasting, the extensive ABA database was utilized to develop a rapid characterization scheme. By implementing a characterization scheme based on total sulphur concentrations and fizz rating, waste rock could be quickly segregated without delaying the natural flow of ore from the pit. Interestingly, it also became apparent that gold values were strongly correlated with total sulphur, such that traditional fire assays were supplanted with a simple and more cost-effective total sulphur determination. The program highlights the importance and benefits of collecting and exploiting data beyond that necessary to acquire appropriate development permits.

Jan 1, 2000

By D. Furrer, M. Dallaire

The arrival of Image analysis in the last 20 years has changed the world of quantitative metallography. Many standard measurement techniques which were previously manual can now be done with fully automated systems. This reduces subjectivity and operator fatigue and therefore enhances the quality of the statistical results. In many laboratories, Titanium Alloy microstructures continue to be evaluated by traditional methods, where quality of results is subject to operator fatigue and level of experience. Advances in Camera technology have tremendously improved image acquisition. One can often see clearly at 500x what can not be observed at 1000x, allowing for a larger area to be analyzed, without the inconveniences associated with very high magnification objectives. Powerful and versatile Image analysis software combined with a high precision motorized stage gives access to a multitude of applications, which were extremely challenging or impossible until now. Image Analysis tools such as Multilayer Grab, which reconstructs an uneven image into one plane of focus (ex. Observation at high magnification of texture resulting from etching) and Mosaic which builds an image from a number of fields of view (ex. Reconstruction of very large grains at low magnifications) expand even further the power and flexibility of IA systems. This presentation will describe how automated methods are applied to the point count method and grain size measurement. We will show how cameras and software work together to permit quantitative measurements of primary alpha and prior beta microstructures, as well as lamellar alpha plate thickness in titanium alloys.Automated and semi automated quantitative measurements of various Titanium microstrures have been assessed, using the Clemex Vision PE. Examples of the methods and steps used are presented.

Jan 1, 2006