Search Documents

By M. B. Dusseault, A. Pirayehgar

"There is concern that hydraulic fracturing (HF) near an existing critically stressed fault could trigger slip and generate a seismic event of significance. To this end, a mathematical discontinuum model representing a naturally fractured rock (NFR) mass containing a fault is created, and fault slip response to fluid injection is studied. UDECTM is used as a Discrete Element Method (DEM) approach to define the seismic moment, and also to assess the influence of injection and slip on further shear slip propagation. In most of the simulations, slip and dilation take place along a number of oriented fracture surfaces, so it is reasonable to assume that in a real case, microseimic emissions would accompany each slip “event”. The moment magnitude scale (Mw) is used to measure the size of the microseismic event in terms of the energy released. Seismic moment is a measure of the total energy (work) released during a seismic event and is used to measure its size. From another aspect, the injection energy is calculated as the total energy required for achieving the hydraulic fracturing; this is viewed as energy to open fractures against the ambient stress field and much of it is potential stored energy that can be released and create discontinuities (work of fracture), deformations (W=F·d), heat and radiated seismic energy. A small amount of the total released energy is transformed to radiated seismic energy and another small amount results in tensile fractures. Fracture energy is used to calculate the work required to create fracture surfaces. Comparing the energy release by fracturing or seismic events indicates their contribution to the total amount of released energy or total work. The amount of energy associated with the stick-slip event is small compared with the overall work done to generate the distortions (i.e. increases in aperture by forcing them open) in the rock mass, and much of the energy in slip is lost as heat from the plastic deformation, rather than as radiated seismic energy.Microseismic monitoring shows the spatial distribution and magnitude of seismicity associated with slip of bedding planes and natural and incipient fractures. Work calculations have been undertaken to look at the various sources of energy storage (elastic strain energy) or dissipation (slip), and likely the energy losses from viscous dissipation could be addressed as well, helping to clarify HF processes in NFRs."

Jan 1, 2015

By I-H. Jung, J. Kim, B. Konar

"The usage of FeNdB permanent magnet, containing Rare earth elements (REEs), is steeply increasing with its demand for wind-turbine and electrical vehicle. The improvement and recycling of the permanent magnet require good understanding of chemistry of all constituent elements. In order to understand the chemical interactions between REEs and Fe, all Fe-RE binary systems have been critically assessed and optimized based on reliable literature data. The Modified Quasichemical Model and Compound energy formalism is employed to model the liquid phase and the solid solutions present in the binary systems respectively. The enthalpy of the liquid and the intermetallic phases showed a systematic trend along the lanthanide series. This helped to mitigate the discrepancies in literature data and also to predict the binary interactions between some less well investigated Fe-RE binary systems. INTRODUCTIONRare Earth elements (REEs) are a group of seventeen elements (including Scandium, Yttrium and the lanthanide series) that exhibit same characteristic chemical and physical properties. These properties make them valuable to the electronic, appliance, green technology, weapon and medical device manufacturing industries. Compounds of REE with other metals (like Co, Fe, Ni etc.) have unique properties of luminescence, thermal and electrical conductivity, magnetism and ability to act as catalysts and polishing compounds (Gschneidner ,2011).They are not only indispensable for some electronic gadgets of today, like computers, music systems, mobile devices, televisions and MRI machines, but also holds a key to more greener technology of the future. They contribute to the development of more efficient and environment friendly version of everyday products such as cars and light bulbs. REE compounds revolutionized the magnet industry by making them smaller and more powerful with increased longevity, and high temperature workability, which are used in motors and generators that power electronics, telecommunications, electric automobiles and turbines(Humphries, 2011)."

Jan 1, 2012

By R. Yost

"This paper describes a case study that illustrates how detailed geological engineering results were communicated to address a range of stability challenges in a producing mining environment. Instead of using standard geological engineering terminology, findings and recommendations were communicated as mine design options and mining responses to accommodate possible slope instabilities and associated risk. The resulting medium- to long-range mine plan integrated the potential slope instabilities and associated mining responses to provide a higher probability of planned resource extraction. It also reduced the potential for long-lasting production and processing delays.RÉSUMÉ Cet article décrit une étude de cas illustrant l’intérêt de la communication de résultats détaillés de géologie appliquée pour résoudre un éventail de difficultés relatives à la stabilité dans un environnement minier en production. Plutôt que d’utiliser une terminologie classique de géologie appliquée, les résultats et les recommandations ont été communiqués sous forme d’options pour la conception d’une mine et de réponses dans le contexte minier permettant de surmonter les éventuelles instabilités des pentes et les risques associés. Le plan de mine sur le moyen à long terme qui a résulté intégrait les instabilités potentielles des pentes ainsi que les réponses connexes dans le contexte minier afin de renforcer la probabilité de l’extraction des ressources prévue. Il réduisait également la possibilité de retards durables dans la production et le traitement.INTRODUCTIONSlope failures in an active mining operation are unscheduled but expected events, in the sense that the geotechnical design often assumes the potential for slope failure but cannot predict exactly when a failure will occur. Unfortunately, the geotechnical engineering cycle—characterization, slope design, displacement monitoring, instability management, and failure remediation—that is necessary to manage slope-failure risk is not always well known or understood outside the geotechnical engineering profession. The first introduction many personnel have to geotechnical engineering is when a slope failure starts to develop and appears to threaten the safety and livelihood of their workplace.At that point, the task of communicating the risk management of slope failure falls to the geotechnical engineer, who must summarize analytical methodology, design concepts, monitoring trends, and analysis results, frequently to an audience with limited exposure to the geotechnical field. All too often, the response has been to present a risk-management plan in the vernacular of geological engineering— using terms such as factor of safety (FOS), pore-pressure reduction, and slope unloading—instead of expressing the problem and solution in more readily understood mine production terms."

Jan 1, 2017

By P. G. Smith, A. Axiuk

The objective of this paper is to present, from a practical perspective, a review of the most relevant maintenance procedures that are accepted or prescribed to be the most effective in optimising service life potential and to ensure continued safe use of steel wire ropes for shaft mining applications. The paper will address the most common operational issues encountered in the care and operation of shaft ropes for both conventional drum hoists and multi-rope friction winders. For each distinct maintenance procedure presented, a limited amount of theory is discussed to identify the underlying mechanisms at play that must be addressed and to emphasize the logical basis for the recommended course of action. It is recognised that each installation is unique and that the recommended maintenance procedures may not always be practical or cost effective from an operations standpoint under select circumstances, however the intent remains to promote industry best practices for the knowledge and benefit of the mine hoisting community, from experienced maintenance personnel to new entrants to the industry alike.

Jan 1, 2023

By K. Iturralde

The topic of this article is the automation and robotization in refurbishment processes of industrial buildings. The need to mold these production spaces is quite universal. Particularly in the regions with a high industrial development and with a lack of buildable land, there is a need to convert this kind of spaces into an improved production system. The latest developments can be a useful tool for achieving a more efficient way of reforming this type of construction. On the one hand we have the digital or computerized 3D Laser Scanning (Computer Aided Measurement) that allows an accurate 3D modeling of the entire building. On the other hand, the project management using BIM (Building Information Modeling) could provide an easy design of each of the elements of the refurbishment. Finally, through the production of construction elements using robotics as jig or for CNC (Computer Numerical Control) we achieve a neat production of each element. How can be all those technologies applied in the refurbishment or expansion of industrial buildings? The research takes a first approach and analyzes industrial buildings that can be called generic or not specialized. To narrow the field of refurbishment, three major factors are defined. The first is to minimize the bill of the energy consumption of the buildings. This could be done either insulating the envelope, reducing the waste-volume to be conditioned climatically or creating facilities for energy production. The second is that the refurbishment or expansion of industrial buildings should try not to interfere on the production process that takes place in the building. In other words, the assembly of the elements in the construction site should be quick and easy, causing the least of disturbance at the workplace. Finally, the research makes an approach towards a robot integrated industrial or productive building .

Aug 1, 2013

By K. C. Marsden, B. Pesic

"Interest in the efficient production and recycling of rare earth elements has increased in recent years along with the prices of these elements. The molten LiCl-KCl eutectic is one ionic solvent which can be utilized for these purposes. The LiCl-KCl eutectic has also been selected as the electrolyte for focused research for advanced pyrochemical recycling processes for used nuclear fuel in several nations. Rare earth elements are fission products with notable neutron absorption characteristics, and thorough understanding of the properties and behavior of these elements is critical to their successful partition from the electrochemically-similar actinide elements. The number of research papers investigating individual rare earth elements has greatly expanded in the approximately 35 years since the last review. These research papers are presented in a variety of languages and technical formats, making data difficult to compare, and are sometimes contradictory. A review and summary of diffusion properties of rare earths in LiCl-KCl eutectic was performed, and the data translated to a common format for evaluation. INTRODUCTIONThe rare earth elements have experienced growing importance in recent decades due to their application in high technology, including optical lenses, lasers, high-temperature superconductors, improved alloys, high energy-density batteries, and powerful magnets for compact electronic devices. Their historic production methods and uses are detailed in several texts (Hampel 1971; Bautista &Jackson 1992; Gupta & Krishnamurthy 2005). A s the p rice o f these e lements has r isen in r ecent years, so has interest in their efficient production and possible recycling options. Rare earth oxides are concentrated through hydrometallurgical techniques, but the high thermochemical stability of their oxides precludes production of rare earth metals in aqueous systems. However, the wide electrochemical window and better control of pO2- in fused salt systems allows the production of these reactive metals from their halides or oxides. The high ionic conductivity and diffusivity of the molten ionic electrolyte allow high currents with limited resistive losses (Fray 1980). Electrolytic methods in fused salts are commonly adopted for the production of bulk rare earths in a variety of molten salt systems. Fluorides are sometimes proposed for oxide electrowinning processes due to ability to dissolve the rare earth oxide, reduced hygroscopic behavior, and the wider electrochemical separation between O2 and halide gas evolution (Mohan Das, Damodaran et al. 1988; Gibilaro, Pivato et al. 2011). However, in most electrolytic production processes, such as that for mischmetal, the rare earth oxides are converted to chloride prior to electrolysis in a chloride bath (Gschneidner Jr. & Eyring 1978; Sharma 1987). Of the chlorides, the LiCl-KCl eutectic is one specific medium in which metal production and production-related investigations have been conducted (Gschneidner J r. & Eyring 1978; Driscoll & Fray 1993). L iCl-KCl eutectic has the advantages o f h igh conductivity, but relatively low viscosity and operating temperature. The low operating temperature allows simpler design, with reduced energy consumption, salt volatility and cell corrosion."

Jan 1, 2012

Diverse and considerable energies are associated with mobile equipment operated and maintained on mine sites. Loss of control of these energies is a common cause of injury on mine sites and this is well recognised by the mining industry. In 2006, 4 multi-national mining companies formed the Earth Moving Equipment Safety Round Table (EMERST), with the aim of engaging collectively with the manufacturers of equipment to accelerate improvements in mining equipment design. Originally focused on surface mining equipment, and particularly haul trucks, the focus of EMESRT widened to include underground and exploration equipment. Since 2006, EMESRT has maintained a program of regular visits and other engagements with a steadily increasing number of manufacturers. The membership of EMESRT has also increased, with 15 companies being members in 2012. An initial step undertaken by the EMESRT members was the development of ?Design Philosophies? which drew of the collective experience of mining companies to identify potential unwanted events which cause equipment related injuries and illness. A technique for analysing risks associated with operation and maintenance tasks, the Operability and Maintainability Analysis Technique (OMAT), was subsequently developed and trialled. In 2011, the EMERST members resolved to propose a common form of safe design information to be requested by all members companies during procurement, and the resulting EMERST Design Evaluation for Equipment Procurement (EDEEP) process was launched at MINExpo in Las Vegas in September 2012. The outcomes of OMAT risk assessment and control activities are integrated during this process into a common ?Safe Design Information? template for communication to prospective purchasers. The aims of requesting manufacturers to follow this process are to provide equipment purchasers with a common way of assessing how well the issues in the EMESRT Design Philosophies are addressed in the equipment design; and to provide manufacturers with additional information for use during equipment design. The process involves identifying priority tasks based on frequency and the severity of the consequences of potential unwanted events identified in the EMESRT Design Philosophies; undertaking a task-based risk assessment of priority tasks in conjunction with site-based personnel; evaluating the effectiveness of control measures; and providing information about safe design features in a standardised format.

Aug 1, 2013

Some examples of the results of research projects, conducted in the KOMAG Institute of Mining Technology are presented. Special attention is paid to mining machines and equipment, and improving work safety and comfort of miners in underground workings. From numerous scientific and technical achievements of the KOMAG Institute within the last 2 years, a few design solutions have been selected for a presentation. Some results of European projects on innovative solutions are described as well, highlighting KOMAG?s role in the national and international research area.

Aug 1, 2013

By K. Kawagishi, J. Ang, A. Sato, H. Harada

"We have recently proposed a new ""EQ Coating"" bond coat system to solve the problem of secondary reaction zone (SRZ) formation caused by bond coats applied on the hot section components of modem jet engines. A viable EQ coating alloy was previously found for a representative znd generation superalloy, TMS-82+. It would be ideal if the same could be done for a representative 5th generation superalloy, TMS-173. In this paper, we will show that the coating with the best oxidation resistance in the EQ system of TMS-173, although possessing considerably better resistance than TMS-173, did not have sufficient oxidation resistance. In order to improve the oxidation resistance of the EQ coating for TMS-173, we have ventured into ""Pseudo-EQ coatings"". A diffusion couple between the Pseudo-EQ coating and TMS-173, after 300hrs at 1100°C, had a 0-15µm IDZ, but no SRZ. A diffusion couple between a conventional coating and TMS-173 formed a 80-150 µm SRZ. After a 1 hr oxidation test at 1100°C, the PseudoEQ coating formed a thinner oxide layer than the EQ coating, but still contained NiO and spinel. Aerospace"

Jan 1, 2006

By Martin G. Wafforn, George J. Greer

"In early 2014, Pan American Silver Corp. commenced a project to construct a second shaft at its La Colorada underground mine located in Zacatecas State in Mexico. This was the first new shaft development project undertaken by Pan American Silver in the history of the company. The existing mine workings permitted the use of a raise bore for the excavation of the shaft opening, utilizing directional drilling in poor ground conditions to advance the pilot hole. This was an interesting project with many challenges and successes, and numerous lessons learned. The project was successfully completed in 2016, with the shaft operating at full mine production capacity within weeks. INTRODUCTION The La Colorada Mine has a long history dating from at least the 1920’s. The mine is located in the northern portion of Zacatecas State in Mexico in the Chalchihuites area, an approximate two hour drive south from the city of Durango. Pan American Silver acquired the La Colorada mining concessions in 1998, with mine production at that time consisting of only a few hundred tonnes per day. Over the course of the following 15 years, with the addition of an oxide processing plant and some expansions to the sulphide processing plant and site infrastructure, production was eventually increased to a maximum of 1,250 tonnes per day, all of it generated from conventional cut-and-fill stopes in the underground mine. An existing shaft was used to hoist the ore to surface, and over the years Pan American Silver had deepened the shaft and had changed out some of the hoisting plant. However, there were historic workings in close proximity to the shaft that made it unsuitable for personnel transport, and shaft maintenance was becoming difficult. The shaft was increasingly considered as a risk to the long term production continuity, and also to further deepening of the mine. In addition, expanding the capacity of this old shaft was not possible. Drilling of the La Colorada mineralization at depth commenced in 2010, with very good exploration success. As a result, by the end of 2013, the mine reserves had grown to a total of 6.5 million tonnes of high grade ore (388 g/t Ag, 0.36 g/t Au, 2.4 % Zn, and 1.3% Pb). Furthermore there were more (and higher grade) sulphide reserves than oxide reserves at depth. Following the completion of an internal study in 2013 with assistance from one of the international shaft contractors, a decision was made to increase the production from the mine with the construction of a new shaft and a new sulphide processing plant, a project with a calculated payback of 2.2 years."

Jan 1, 2019

By Martin Landwehr

"Dust samplers are based on different principles. The konimeter is based on the number of particles counted; mining applications are based on routine sampling; and the photometrical evaluation of samples is used after the pre-separation of particles above 5 micron by the mining konimeter. In special cases, the Draeger sampler is used for quantitative analysis. General trends are toward larger samples, concentration on a weight basis, fractionation into size groups by different techniques and an analysis of composition. Standards or TLVs already exist in all industries. Surface industries base their criteria on concentrations and quartz contents in particles below 5 micron. The mining industry uses the tyndalloscope routinely to determine concentrations; concurrent] y, the rock content, as deter-mined by ashing samples, is obtained by konimeter.Threshold limits are related to the rock content in respirable fractions and tyndallometrically determined concentrations. The TL Vs are based empirically on Landwehr's ""dust values,"" as agreed upon with the Mines Inspectorates. Recently, and in accurate sampling, dust samplers have been used that count the dust in two fractions -above and below 5 microns. Mineral composition is determined either for all minerais or just for quartz. In assessing the dust hazard by Landwehr's ""dust values,"" all minerais are taken into consideration; in coal dust sampling, however, only the quartz content is taken into account. Efforts are now being made to co-ordinate the different assessment methods, arriving at uniform MAC values in agreement with those of other countries."

Jan 1, 1969

By H. E. Pawson

Giant Yellowknife is located 600 air miles north of Edmonton on the north shore of Great Slave Lake in the Northwest Territories. In its 24 years of operation some 7,730,000 tons of ore have been treated to yield $175,000,000 worth of gold.The gold ore occurs at irregular intervals throughout a fold-like sericite schist zone cutting Precambrian rocks. The ore is characterized by 40 to 80% quartz - carbonate and about 10% pyrite and arsenopyrite. Considerable amounts of stibnite and antimony sulpho-salts are also present. Gold is finely divided in the native state existing in complex association with the sulphides. In most instances stibnite is barren but minor values are evident on occasion. Visible native Fold, quite prevalent in the early operating years, is, practically non-existent today. It was readily apparent from mineral dressing investigations conducted in .1944 that Giant ore would be difficult to treat. By 1948 a flow sheet had been established and operations began. In the ensuing years, changing ore characteristics necessitated modifications to some process steps and complete abandonment of others. By 1962 the major metallurgical problems were solved and all that remained was the refining of operating performance to its highest level.With one or two exceptions today's operation follows the practice established by 1962 (Fig. 1 - Flowsheet).

Jan 1, 1973

By David S. Robertson

"IntroductionCanada has been one of the world's leading producers of uranium since atomic energy first became of practical importance in 1942. Indeed, prior to this time, between 1933 and 1940, Canada produced significant amounts of pitchblende, as a source of radium, from the Eldorado Mine at Great Bear Lake*.Uranium was first reported in Canada, however, in the middle of the 19th Century in the vicinity of Theano Point on Lake Superior north of Sault Ste. Marie. In the early 1900s, uranium-bearing minerals were reported in Quebec north of the St. Lawrence River and in pegmatites in Quebec and eastern Ontario. In 1930, G.A. LaBine and E.C. St. Paul visited an occurrence of cobalt reported by the Geological Survey of Canada in 1900, and brought the Eldorado Mine into production in 1933, as noted above, producing, in the main, silver and pitchblende.In 1942, developments in atomic energy were such that the Government of Canada, at the behest of Great Britain and the United States, requested that Eldorado, which had been closed in 1940, be re-opened to produce uranium for the Manhattan Project. In September, 1943, all discoveries of radioactive minerals were reserved to the Crown and their staking by private interests was banned. In January, 1944, the government nationalized Eldorado and formed a Crown corporation, the present Eldorado Nuclear Limited, to take over the assets. That year marked the formal beginning of uranium exploration in Canada.The Period 1944 to 1948In 1944, the Crown Corporation and the Geological Survey of Canada began exploring for uranium deposits, largely in the areas of Great Bear Lake and Lake Athabasca. In that year, A. W. Joliffe of the Survey visited properties on the north shore of Lake Athabasca near Beaverlodge Lake and recommended that Eldorado acquire claims in the area. In 1946, P. St. Louis and E. Laurum, prospectors working for Eldorado, found the pitchblende veinlets that led to the Ace Mine. Shaft sinking began in 1951, and production, through a carbonate leach plant, began in 1953.Continuing drilling on the Eldorado claims led to the Verna ore bodies, some 6,000 feet northeast of Ace, on which shaft sinking started in 1954."

Jan 1, 1986

By S. Demetrio

China has a traditional segment of Copper Smelters with its own Chinese technology, typically small in size from 20.000 to 50.000 tCu/a, and they are responsible for the processing and production of more than 600,000 tonnes of blister copper per year. For occidental experts, like one of the authors, it is not so easy to believe that they are profitable, because the size and the use of old Blast Furnaces, but they are with simple and effective production lines. The authors are convinced that China has a good alternative to improve theses old copper production lines with small innovative changes in its process arrangement, jumping to higher level technology, more efficient in production, productivity and cost, assuring copper as a raw material for the country and its high speed development. The key to improve that the traditional Chinese Copper Smelter is white metal as an extra raw material as a first step doubling the copper production from raw materials and the complete replacement of concentrates by white metal (WM) in a second step increasing it four times or more as the final goal. It is not so difficult nor expensive to make it happen, but there are a couple of questions for implementing this innovation in the copper smelter industry: 1 - Will the old fashioned mentality be open to this new direction for China being the biggest copper consumer on one side, and the biggest copper Primary Producers on the other hand? and 2 - Will they be open to follow this "win-win" strategic way for both ends of the copper market? We don't know if anybody will take up the challenge to improve it but our responsibility as a consulting expert and a university professor is to put the alternative on table for others to decide whether to implement it.

Jan 1, 2007

By Bryan Wilson

Background ?Nickel Rim South Mine started production ramp-up in Q2, 2009. ?The main dewatering pumps were put into use in August 2009. ?3 Feluwa?multisafe?positive displacement pumps ?1700m single lift pumping ?Reliability has been an issue due to the amount of slimes and fibers (from shotcrete) at the pumps. ?Critiqued internal dewatering system to solve some issues we were having with our sumps Findings 1.Much of the final dewatering system was not in place. a)Temporary pain. Difficult to say something is not working when the system was not yet in place as per design. b)Not enough capacity to handle slimes within the system. 2.Need to address issues with the final design: a)Ongoing costs: The end design has operating costs of $2.5 million b)Scoops in Sumps: The end design relies on scoops to be used for cleaning the sumps c)Slimes Recovery: The system mixes 3 different products in the sumps along with the fibers d)Pump repair costs: The existing Tsurumi pumps are too light duty for our slimes

Nov 1, 2011

By Z. I. Zaki

Synthesis of TiC /A1203 Composite from TiO2, Al and graphite using combustion technique has been investigated at different initial temperatures; room, 400 and 600 °C. The effect of initial temperature on the composition of the product, wave velocity and combustion temperature of the reaction was studied. The measured combustion temperature and wave velocity were increased with increasing the initial temperature of the combustion reaction. The maximum wave velocity obtained was 5.9mms-1 when conducting the combustion reaction at initial temperature of 600 °C. Oxidation resistance of the obtained composite was also studied at the temperature range 300-800 °C. No oxidation is detected before 400 °C while it takes place effectively at 700 °C forming different titanium oxides. Wave velocity measurements method was used to calculate the activation energy of the reaction between the starting materials. It was found to be 316.34 kJ mol 1 at the temperature range that was studied.

Jan 1, 2007

By H. F. Naldrett

"AbstractAt the end of May, 1950, Imperial Oil, Limited, had completed a total of 192 D-3 wells in the Leduc-Woodbend field, 62 of which lost circulation in the D-3 zone for periods ranging from two hours to fifty days. The majority of the remaining wells •lost some mud without actual loss of returns. In addition, independent operators completed 69 D-3 wells, of which 9 lost circulation. Included among the latter is the now well known Atlantic No. 3 well, which blew wild out of control for seven months. The well was finally brought under control through two directionally drilled wells, but not before the derrick fell and the well caught fire. Practically all known filler materials have been used in attempt3 to prevent or regain loss of circulation, but none has been successful, except in minor cases. Ordinary sawdust has come to be the most commonly used filler material and is added to the mud before the D-3 zone is contacted. In cases of serious loss of circulation, the on1y successful method of getting returns has been the use of a series of small cement plugs.IntroductionThe Leduc field is twenty miles southwest of Edmonton, Alberta. Geologically, it is on the east limb of the Alberta syncline, in the homoclinal belt. The main productive zones are in the Upper Devonian formation and are known locally as the D-2 zone and D-3 zone, respectively (see Figure 1).The D-3 zone is a dolomitized reef with fair average porosity and permeability, and shows considerable evidence of vertical fracturing. Porosity is mainly due to moderately uniform development of vugs which are interconnected by small crevices. However, the formation is known to be, locally, extremely vuggy and in places cavernous. These latter conditions create very serious drilling problems due to the hazard of loss of circulation, particularly in the gas cap, which has a maximum thickness of 200 feet. The D-3 zone is contacted at an average depth of 5,300 feet."

Jan 1, 1950

By L. A. Nazarova, M. Vandamme, L. A. Nazarov, R. I. Rodin

"The paper describes a new method of interpreting the “canister test” data for the quantitative estimation of gas-kinetic parameters of coal bed based on the developed model of gas emission from coal sample placed in a sealed container. The model accounts for grain-size composition of the sample, initial gas content S, as well as coefficients of diffusion D and mass transfer ?. The inverse coefficient problem is formulated to find S, D and ??from the data of pressure measurements in the sealed container. It is shown that the inverse problem is uniquely solvable if the pressure is dropped during the experiment. The method has been tested using the data from an underground coal mine in the Kuznetsk Basin.Based on the poroelastic model of a coal bed and Khristianovich’s concept about origination and evolution of the filtration zone F in the neighborhood of a degassing borehole the authors considered the corresponding direct problem on rock mass geomechanical state. It was offered interpretation method for data on pressure measurements in a plugged degassing borehole allows evaluation of the diffusion coefficient, the horizontal component of natural stress field and parameters of F. The related inverse problem of the mixed type is formulated, and the cost function is constructed. The analysis using synthetic input data has shown that the cost function has a number of local minimums arranged on the same straight line, one of the minimums being the inverse problem solution. INTRODUCTIONPre-mine degassing is an integral part of coal mining. It allows mitigation of induced accidents in mines (coal and gas outbursts, rock bursts) (Guide, 1990; Malyshev & Airuni, 1999; Seidle, 2011) and also furnishes an alternative and ecology-friendly energy source—methane (Rice, 1997; Nambo, 2001). Choosing an optimized pattern of degassing boreholes, as well as estimating degassing time and amount of gas recovered requires data on gas-kinetics indices of coal beds out of which the key parameter is a gas content S. According to the latest guidelines for coal mines in Russia (Ruban et al, 2012), mining is allowed if S in a coal bed section is under 7 kg/m3."

Jan 1, 2015

By Y. Tang

"Rare earth elements (REEs) have many key applications in traditional and advanced technologies. A shortage of several critical REEs is expected due to the discrepancy between the availability of REEs from REE deposits and the REE demand from the market. REE recovery and separation from secondary resources such as uranium wastes and recycled materials might help balance the shortfall in a cost-effective way. This paper presents data concerning the recovery of heavy REEs (HREEs) from uranium raffinate. It also discusses the design, commissioning, and operation of a solvent extraction pilot plant for the separation of REEs.RÉSUMÉ Les éléments des terres rares (ÉTR) trouvent de nombreuses applications importantes dans les technologies classiques et de pointe. On prévoit une pénurie de plusieurs ÉTR critiques en raison des divergences constatées entre la disponibilité des ÉTR provenant de gisement d’éléments des terres rares, et la demande d’ÉTR sur le marché. La récupération et la séparation des ÉTR à partir de ressources secondaires telles que les déchets générés par le traitement du minerai d’uranium et les matériaux recyclés pourraient contribuer à équilibrer cette pénurie de manière rentable. Cet article présente des données relatives à la récupération des ÉTR lourds (HREE, de l’anglais heavy REEs) à partir de raffinat d’uranium. Il aborde également la question de la conception, de la mise en service et de l’exploitation d’une usine pilote d’extraction par solvants pour la séparation des ÉTR INTRODUCTIONSignificant amounts of strategic specialty heavy rare earth elements (HREEs) are present in waste streams in Saskatchewan uranium operations. Selective precipitation including neutralization, oxalate, and double-salt precipitation, as well as sulfide precipitation, ion exchange (IX), and solvent extraction (SX) are commonly used technologies for the recovery and purification of rare earth element (REE) solutions. REE oxalate precipitation can effectively remove Fe, Al, Ca, Si, and other impurities by taking advantage of the solubility difference between REE oxalates and impurities in the acidic solution (Xu, 2005)."

Jan 1, 2018

By V. I. Lakshmanan

Recycling helps to save energy and is good for the environment. It is also important for preserving the limited natural resources. In addition, recycling creates economic benefits and frees up space at the landfill sites. Process Research Ortech Inc. (PRO) has conducted extensive testwork in the area of waste processing and recycling. A process was developed for the recovery of Zinc from galvanized steel by alkaline leaching followed by solvent extraction and electrowinning. Extensive testwork has been conducted at PRO to obtain a useful by-product from rice husk. Rice husk was combusted in a gas/solid reactor to obtain an environmentally acceptable amorphous silica ash suitable for use in high strength concrete. In another development, vanadium was recovered from fly ash by separating carbon first, followed by alkaline pressure leaching, solvent extraction and precipitation. PRO has also developed an environment friendly process for treatment of industrial wastewater for its reuse to obtain zero or minimal effluent discharge. In this paper, four case studies related to recycling of zinc scrap, controlled combustion of rice husk, processing of fly ash, and reuse of waste water will be discussed.

Jan 1, 2011