Search Documents

By Boyd Davis, Brook Zaback

"Among the first published papers from Prof. Torstein Utigard was work on imaging the aluminum electrolysis process and in-situ measurements of aluminum in cryolite melts. He and Prof. Jim Toguri used an x-ray radiographic technique to measure interfacial tension of aluminum drops. Publications using this equipment for aluminum electrolysis spanned from 1985 to 2006. As well, other methods were used to better understand electrolysis in molten salts, including hot-stage microscopy, direct observations from above the bath and water modeling techniques. For chloride systems (for magnesium and lithium), it is possible to see side-on the electrolysis using a quartz cell. In honour of Prof. Utigard’s contribution to this field, this paper presents a summary of work on visualization of molten salt electrolysis, including work done at the authors’ labs and others around the world. The paper will summarize key findings and their possible impact on molten salt electrolysis."

Jan 1, 2015

By Parviz N. Farsangi, Ferri P. Hassani, Allen G. Hayward

"Kidd Creek Mines places approximately 10 000 tonnes of consolidated rockfill (CRF) daily. Consolidated rockfill comprises sized aggregate mixed with different ratios and amounts of binders. Consolidated rockfill is employed to simplify subsequent pillar recovery and provide improved passive/active ground support.The consolidated rockfill is designed to sustain not only the gravitational loading of the overlaying fill material, but also to some extent the dynamic loading applied during blasting of the adjacent stopes and/or pillars. This paper describes the steps taken to optimize the pre-sent fill system at Kidd Creek Mines.The emphasis is on four areas which have high saving potential: lower cost alternative binders, structural design, quality control measures, in-situ testing techniques for back analysis. A consolidated rockfill design optimization chart was developed from these investigations."

Jan 1, 1996

By E P. Graham

Orebodies occur in an infinite variety of grades, shapes and sizes, and take many millions of years to grow. When extraction starts there is only one possible end -the mine sooner or later will run out of ore and shut down. If the mineral industry is to supply the ever increasing demands of modern civilizations, more and more metals must be found and mined. This will require a never-ending search for ore, and the development of every economic body, large or small. To justify the mining of a small orebody, it first of all must pay its way. If the size of the burden imposed by the capital cost estimates is not carefully worked out, an otherwise promising situation could be killed. The very nature of mining, as a transient industry, re-leases a steady stream of good used equipment, and the trained personnel to install and operate it. All manner of plans and layouts, which can be utilized at a new property, are available. Working these and other economies into the estimates will sometimes make enough difference to give a prospect the green light.

Jan 1, 1964

By M. Reda

Inorganic oxidizing agents of the type MeOx-z such as Chromate, Vanadate, Tungstate, and Molybdate... etc. are widely used as corrosion inhibitor. In non acidic solution these oxidizing agent are reduced on the surface of the meta, according to OX + m e + p H20 Red + n OH" In which y = (n-m)/m. The purpose of this publication is to show that for many metals the value of y for any oxidizing agent determines the possibility of that oxidizing agent being an inhibitor or activator for the corrosion process. The inhibition efficiency for other ions such as Pertecnetate and Tellurate which have not been extensively studied can be predicted. A mathematical, equation was derived to express the relationship among the concentration of oxidizing agent, degree of retardation of the corrosion process I cord cor ° (ratio of corrosion current in the solution containing inhibitor to the base solution) , ionic strength of the solution and the coefficient y. The validity of y and the mathematical, equation were verified by many experimental, works on various metals such as zinc, aluminum and steel. Al, the above research works are based on the published research works of Prof. Mikhailoviskii (from 1979 til, 1998) from the Russian Academy of Science.

Jan 1, 2010

By J. Ita, F. Malekzadeh

"Multi-scale simulation in coupled fluid flow- geomechanical systems is a computationally efficient method for numerically solving large poroelastic systems. When using multi-scale methods, care must be taken in ensuring consistency when information is exchanged between systems that have a different discretization. Here a method is presented which provides consistency between the pore pressure being calculated on a fine scale fluid flow domain and upscaled to the coarser scale geomechanical domain and the pore volume change being calculated on the coarse geomechanical domain and down-scaled to the fine fluid flow domain. Central to this process is the characterization of the mechanical properties of the poroelastic system at both scales.Another advantage of the method presented here is that it is applicable to hydraulically disconnected but laterally drained (i.e. multi-porosity) layered systems as well as hydraulically connected, layered systems. Thus it can be used in geological situations where thin shale streaks or hardpans impede flow between laterally extensive, hydraulically conductive units. This is significant as the pressure evolution of such a hydraulically disconnected, laterally drained system can be very different than a hydraulically connected one as shown here. INTRODUCTIONA multi-scale treatment of fluid flow and deformation is a key enabler when simulation of poroelastic phenomena is limited by computational resources. As the spatial domain of the geomechanics model is usually larger than the fluid flow model, it is desireable to use a coarser discretization in the geomechanical model compared to the fluid-flow model. This type of multi-scale simulation requires a consistent up-scaling of pore pressure from the fine scale fluid flow model to the coarse scale geomechanical model and down-scaling of pore volume change from the geomechanical model to the fluid flow model (see Figure 1)."

Jan 1, 2015

By Barry J. Turley

With over 700 large electric-drive haulage trucks operating in Canadian mining today and over 3700 in mines worldwide, most aspects of electric drive are well known. Recently, however, extensive application of these trucks to down-hill hauling in mountain mining makes it vitally important that many of us better understand the operation and proper application of the dynamic retarding feature of these vehicles. This paper is an attempt to clear up misunderstandings on this subject, to suggest precautions that mining operators should take in comparing competitive retarding systems and to challenge equipment manufacturers to evolve improvements to the important aspect of system performance.

Jan 1, 1978

By R. P. D. Graham

It is almost exactly two hundred years since the foundations of the mining and metallurgical industries in Canada were laid. There '."'as nothing spectacular about this early start. It had to do with the most basic phases of these industries-the mining of coal and iron ore, and the manufacture of cast and wrought iron. At several points along the coast of Cape Breton island, coal seams may be seen outcropping quite conspicuously, and it is probable that they had been observed, and possibly worked in a small way, in very early times. However that may be, these coal seams have the distinction of being the first in North America of which there is any printed record, reference to them appearing in a volume by Nicolas Denys which was published in Paris in 1672. Regular coal mining in the district did not commence until about fifty years later, however. The metallurgists started their operations along the north shore of the St. Lawrence river. Here, at many points between Montreal and Quebec, are to be found deposits of bog iron ore, and in 1 730 a furnace for smelting such ore was established on the St. Maurice river. The St. Maurice forges continued in operation until 1880, and throughout that long period they were famed for the fine quality of castings produced, and also for a-superior wrought iron.

Jan 1, 1924

"Far from being eclipsed by petroleum and natural gas, Canadian coal continues to command wide (and apparently growing) interest.Major R & D investigations are currently heavily oriented toward coal beneficiation (e.g., cleaning and utilization of fines) and toward a broad range of studies on metallurgical coals and cokes. However, active work is also being carried out in the areas of coal geology, mining, transportation and combustion; and, in some laboratories, increasing stress has been laid on developing a number of new, essentially non-fuel uses for coal and coal products.This review summarizes the work of Canadian coal research agencies during 1966 and indicates some of the more important advances made by them."

Jan 1, 1967

By B. S. Kim, Y. D. Kim, T. S. Kim, T. B. Kim, H. J. Chae

"The Nd-Fe-B scrap was placed in Fe crucible with pure Mg in an Ar atmosphere, and the scraps were melted using an induction heating method. The effects of experimental parameters such as melting temperature (range of 993K to 1073K) and holding time (15min-600min) on the ability of extraction were investigated. The microstructure and diffusion layers were analyzed by Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS), and the constituent phases were characterized using XRay Diffraction (XRD). Diffusion of Nd through the Nd-Fe-B scrap into liquid Mg was described, and the diffusion coefficient of Nd in liquid Mg was estimated.INTRODUCTIONNd-Fe-B magnets are usually produced either from comminuted melt-spun ribbons as bonded magnets or hot pressed bulk magnets, or by sintering in conjunction with prior green compaction in an applied magnetic field (Sagawa et al., 1984). These magnets have been widely used for various electromechanical and electronic devices such as voice coil motors (VCMs) and magnetic resonance imaging (MRI) (Samardzija et al., 2012; Matsuura et al., 2006). The production of the Nd-Fe-B magnets is increasing by about 20% per year because of their excellent magnetic properties. However, the expansion of Nd-Fe-B magnet market induced a concern for the scarcity of Nd at the aspect of natural resource. Therefore, the development of an effective recycling process for Nd-Fe-B magnet scraps is an extremely important issue from the viewpoint of resource and energy conservation. Several recycling processes for the Nd-Fe-B magnets have been proposed (Uda et al., 2002; Lyman et al., 1993]. It has been reported that the best separation of rare-earths from the Nd-Fe-B magnets is obtained by sulfuric acid dissolution followed by precipitation of recyclable rare-earth salts. However, this process can make a large amount of waste water including dangerous solutions. Recently, (Xu et al., 2000) have reported a technique to extract Nd from 18Nd-72.4Fe-0.9B-1.82Pr-5.3Dy (wt.%) magnet scrap by using liquid metal extraction (LME) processing. However, these techniques seemed to be difficult for application, because the scraps consist of an infinitesimal amount of other minor elements (Pr, Dy, Cu, Al and Tb), and these minor elements can make a new intermetallic compounds with Mg. Also, some oxides or the plated Ni metal can be preventable to reaction between solid-liquid (S/L) interfaces. For these reasons, the substantive reaction mechanism between Mg and Nd-Fe-B scrap is not clear. In this study, the simple composition of 33Nd-66Fe-1B (wt.%) magnet scraps were prepared using an induction melting process. The effects of the experimental parameter on the diffusion properties between Mg and scraps were investigated to determine whether these methods could be used in industrial application in a liquid metal extraction (LME) process."

Jan 1, 2012

By N. M. Steven, J. M. Moore, J. L. Kuyper

Abstract - Mineral exploration and research has led to the identification of four types of tungsten mineralization in the NE-trending, largely ensialic, inland branch of the late Proterozoic/early Paleozoic Pan-African Damara Orogen. The mineralization (mainly scheelite) occurs in a terrane (the Central Zone) that is characterized by multiple deformation, greenschist/amphibolite-facies metamorphism and numerous peraluminous S-type granitic and pegmatitic intrusions. The four major types of scheelite mineralization are (in ascending stratigraphie order of host rock): (1) thin (5 cm to 2 meter) quartz+ plagioclase+ diopside ± scapolite cale-silicate granofels with finely disseminated scheelite (scheelite-bearing granofels; SBG) developed as discontinuous intercalations within the cale-silicate rocks of the Khan, Spes Bona, Oberwasser and Kuiseb Formations (Nosib and Swakop Groups); garnet+ pyroxene ± vesuvianite + scheelite ± fluorite replacement skarns hosted by Okawayo, Karibib and lower Kuiseb Formation marbles in the aureoles of late tectonic, unmineralized leucogranites; metaturbidite-hosted scheelite- (and possibly wolfrarnite-) bearing tourmalinites, both stratiform and crosscutting, in the Kuiseb Formation located in the 'cleavage fronts' of late tectonic granitoids; scheelite-bearing vesuvianite +quartz+ garnet skarnoid rocks (several hundred meters in length) in the calcareous metaturbidites of the upper Kuiseb Formation. These scheelite occurrences were discovered by the follow-up of a large number of tungsten anomalies located during a regional stream sediment sampling program. Detailed mapping, ultra-violet surveys and rock sampling proved to be the most effective surface exploration techniques for locating mineralization; soil sampling and geophysics were of almost no use. The largest, continuous scheelite-bearing skarn of economic interest, Otjua, has a drill-indicated reserve of 250 000 tonnes at 0.53 wt% W03 and 8 wt% CaF2.

Jan 1, 1994

By Rene Cane, V. I. Lakshmanan, John Starkey, Richard May

"The Agrium Kapuskasing Phosphate Operation mines and processes up to 6,000 t/d of phosphate ore. Run-of-mine crushing to minus 6 inches is done in a toothed roll-crusher, while grinding is done in a SAG/ball mill circuit with no coarse recycle classification of the SAG mill discharge. The primary grinding mill is an 18 ft. diameter x 9 ft. EGL, 1500 HP variable speed SAG mill and the secondary mill is a 13 ft. diameter x 21 ft. long, 2000 HP fixed speed, ball mill. When hard ore was treated, the SAG mill restricted the tonnage that could be ground. When soft ore was treated, the ball mill and spiral classifier overloaded and restricted throughput.Recommendations from a plant benchmark and an ore hardness testing program, on how to better utilize installed energy in the Agrium SAG mill when treating soft ore, and how to obtain best results when treating hard ore, were checked in a pilot plant investigation in the 3 ft. diameter Starkey-PRO Pilot SAG Mill. Correlation between the ore hardness testing and the results from the 3’ Pilot SAG mill was very good. In addition, the work indicated the results that could be expected for the different ore types when using either smaller SAG discharge grates and/or a vibrating screen with 10 mesh square opening cloth.INTRODUCTIONAgrium Kapuskasing Phosphate Operation consists of a 6800 t/d open pit mine and a concentrator, near the Town of Kapuskasing in Northern Ontario. The two major ore types are sandy ore and cemented ore. Sandy ore is fine, soft and easy to grind in the SAG mill while cemented ore is harder, more blocky and difficult to grind in the SAG mill. The ratio of sandy to cemented ore in the deposit is thought to be in the order of 80:20 but can range as high as 5050, so it was important for the grinding circuit to have the ability to treat sandy ore alone."

Jan 1, 2002

By J. D. Aitken

"DEFINITION OF THE REGIONTHE REGION considered in this paper is bounded on the south by the 60th parallel, on the north by the Beau-fort Sea and Amundsen Gulf, on the east by Archean rocks or by highly deformed Proterozoic rocks of the Canadian Shield (certain weakly deformed Proterozoic strata being regarded as belonging to the Great Plains), and on the west mainly by the Mackenzie and Richardson Mountains.Only the unmetamorphosed strata of the region are considered; that is, the geology of the crystalline basement is ignored.SIGNIFICANCE OF THE REGIONThe region is significant from three points of view -namely, the economic, the scientific and the social. It constitutes 46 per cent of the area of the Western Canada Sedimentary Basin."

Jan 1, 1970

By M. E. D. Raymont

"During the history of the sulphur industry there have been three distinct phases of production. Factors controlling supplies during these periods have shifted from demand for sulphur to demand for energy and a cleaner environment. The pattern of brimstone production is t raced through these phases and includes estimates of future supply; these indicate an involuntary excess production of some 20 million plus tons per year by 1980 unless some large-scale new uses are found. Traditional uses for sulphur, including fertilizer, chemicals, fibers, etc., are generally expanding slowly; how• ever, supply in ""by-product"" form alone will soon outstrip demand. The predicted oversupply situation can be corrected by the development of novel potential markets. Promising areas include construction materials, insulation and plastics, among others."

Jan 1, 1972

By John J. Jonas, Hong Qin

Cylindrical samples of pure titanium were subjected to uniaxial compression at room temperature, leading to the formation of three generations of twins. Many primary contraction twins were observed as the initial texture was favourable for their formation. Numerous secondary extension twins formed within the primary contraction twins and some tertiary contraction twins within the secondary extension twins. The orientations of these three generations of twins were determined by electron backscatter diffraction techniques and their associated Schmid factors (SFs) were calculated. The formation of the twin variants selected in each generation and the absence of certain potential variants are accounted for by rotating the twinning displacement gradient tensor expressed in the twin system reference frame into the crystallographic reference frame of the relevant neighbouring grain. The presence of the observed primary, secondary and tertiary twins is explained in terms of the ease of imposing the required accommodation strains on the neighbouring grains. By contrast, certain first, second and third generation potential high SF twins were absent because their formation would have required accommodation by the most difficult deformation mode: pyramidal glide.

Jan 1, 2015

By F. Baczek, S. S. Rocks, D. Chaiko, T. Walters

The atmospheric leaching of chalcopyrite concentrates using acidic ferric sulfate lixiviants is well known to suffer from slow leach kinetics and poor copper recoveries. A number of approaches have been proposed for improving both leach kinetics and recoveries in this system. Many of these, while effective, suffer from high CAPEX and/or OPEX. As many mine sites begin transitioning from heap leaching of copper oxides to processing of primary copper sulfides, cost-efficient leach processes that are compatible with existing SX/EW processes will be needed to maintain existing cathode production. To this end, FLSmidth is exploring process options and reactor technology for the hydrometallurgical processing of primary sulfides. One approach that appears to be highly effective at increasing copper recoveries takes advantage of the enhanced reactivity of transitory, surface-defect structures generated during particle fracture. Significant process efficiencies are gained by matching the rate of grinding to the rate of electrochemical leaching in Mechano-Chemical leach processes. The patent-pending FLSmidth® ROL process uses a Stirred Media Reactor (SMRt reactor) to achieve copper recoveries of 97+% in 6 hours or less. This approach overcomes many of the surface passivation problems that have hindered other atmospheric leach processes. New insights to leach mechanisms are presented.

Jan 1, 2015

By A. H. Burns

"Regenerative and recuperative burner systems require advanced combustion techniques to minimize NOx emissions. Various methods of pollutant minimization and furnace design considerations are described. Cited examples are a large high temperature furnace and a small Zinc vaporizing furnace. The concept of total carbon footprint is introduced. The application of Biomass combustion as an effective method of cost and green-house gas (GHG) reduction is discussed. Practical considerations of scale, location and process limitations are discussed. Two examples of biomass fired equipment are cited. Ideal sites have large biomass resources available locally. Processed biomass fuels will be an important substitute for fossil fuel. INTRODUCTIONIn 1992, I presented a paper entitled Combustion Strategies In The Modern Industrial Environment (1992). At that time an abundant supply of cheap fossil fuel made many of the measures I talked about difficult to justify for anything but new equipment.Since 1992 we, as a society, have demonstrated an ability to accelerate the pace of industrial and societal change. The term industrial revolution applied to this age of incessant change is completely meaningless, implying a discrete moment in historical time. What our society has built is a system capable of unfettered, continuous and accelerating technological change. With this change comes an increasing demand for energy and materials.This year is the anniversary of the Titanic disaster, a moment in time when technological certainty met the caprice of nature and gave us a brutal reminder of what can happen to us if we underestimate that power (Mowbray, 1912). In the intervening interval we have regained the technological arrogance that was lost in 1912 bringing us back to the problems of climate change and the need for sustainable industrial activities.We use advanced mathematics to describe many complex systems, sometimes with disastrous results. For example there has been a recent attempt to model the global economy as a completely deterministic system. This premise is flawed at its foundation as human nature and emotion are indeterminate constants in the equations, yielding probabilistic solutions at best. As engineers we are all familiar with stiff problems. The solution to such a problem is meaningless and we have all had the misfortune to live through and rue the effects of that miscalculation over the last few years."

Jan 1, 2012

By A. P. Yovanovic, P. Bonadia, M. N. Moraes, C. F. Matos

"The magnesite flotation operation of Magnesita Refractories, in Brumado – Brazil, has four parallel ball mills working in closed circuit with hydrocyclones to grind the ore for the reverse flotation of silicates in mechanical cells. The modification proposed here opens the circuit for three of the ball mills so that their products are collected together to feed a high frequency screen. The oversize of the screen feeds the fourth ball mill in closed circuit for secondary comminution. The product reports to dewatering and flotation. The undersize undergoes desliming and subsequent flotation operation. According to pilot tests performed, the modification on the magnesite flotation operation will promote a 20% increase in the productivity, 8.5% increase in mass recovery and a 26% reduction in water consumption. The gains are due to the fact that the silicates in the feed are concentrated in the smaller particles (<100µm) with over grinding in the existing closed comminution circuit, making it impossible to take advantage of this natural selectivity. The combination of open circuit, more selective milling, and the high frequency screen, ensures high efficiency particle size classification. This renders the process more effective, both to the screen undersize with its high contents of silicates and fines, and to the screen oversize, which is almost without fines and has a higher magnesite grade. This situation allows for the setting of specific parameters for the flotation of both the primary milling undersize and the secondary milling product.INTRODUCTIONMagnesita Refractories, with its operations site in Brumado, is the largest producer of high purity dead burned magnesia (DBM) in Latin America. The magnesite ore is extracted from an open pit mine, named Pomba, after which it is crushed and handpicked. Due to the presence of disseminated silicate the ore has to be ground and concentrated by means of reverse flotation, before feeding the high temperature kilns for sintering and conversion to DBM.The magnesite flotation unit has an impact crusher to reduce the size of the feeding ore, which is transported to the mills by conveyor belts. The milling operation is composed of four ball mills in closed circuit with hydrocyclones. The closed circuit generates a high circulating load with excess fines, which is detrimental to the selectivity of the desliming and flotation operations, reducing both mass andmetallurgical recovery.In the current scenario, the capacity of the flotation plant is insufficient to meet the demand of the DBM kilns, forcing the operation to work with high purity ores in order to attain the highest possible mass recovery in the concentration process. This is not an ideal situation as it requires the mining site to work with higher stripping ratios.The objective of this work was to improve the magnesite flotation unity to increase its productivity. After a detailed analysis, the milling was identified as the limiting process, which made the authors to focus on this operation."

Jan 1, 2016

By B. R. MacKay

Introduction Of all Canada&apos;s mineral resources, its coal deposits have probably received the most continued attention by the Geological Survey since its inception ninety years ago. A casual review of the many geological maps of coal areas by the Geological Survey will show how geological and topographical detail on the maps has gradually increased to meet the ever urgent demands of the mining industry. In the early stages of exploration, the mapping done, especially in the coalfields of the Rocky mountains, was largely of a reconnaissance nature. On these maps the topographical relief, where shown, is indicated by form lines or by hachures, the boundaries of the coal-bearing formations are only approximately defined, and the geological structure of the coal seams is illustrated by one or more generalized cross-sections. Once mining development on a coal area began, there arose a demand for more detailed maps. To meet this need, topographical and geological maps on a scale of one inch to a mile were made, in which the ?topographical relief is shown by contour lines having generally an interval of 100 or 200feet. On the geological maps, the boundaries of the formations are accurately delineated, and the geological structure of the area is illustrated by one or more structure sections drawn across the area, which show the position and attitude of fault lines, the crests and troughs of folds, and the attitude of the various formations (See maps of Costigan Coal Field, 1905, and Cascade Coal Basin, 1907, by D. B. Dowling).

Jan 1, 1932

By Colin E. Dunn

The high mobility of gold within the plant kingdom results in detectable accumulations of gold in many plants. Concentrations vary within individuals, among species, and with seasons. From an evaluation of the chemistry of easily acce sible organs of common pecies in the northern forests, it is concluded that alder twigs (or leaves) and conifer bark scales are the vegetation components of greatest use in the earch for concealed gold mineralization. Maximum anomaly enhancement is obtained from twigs collected in the spring. Examples are given of urvey conducted in the La Ronge Domain using 1) jack pine bark (A nglo-Rouyn and Upise Lake areas) ; 2) alder twig (McLennan Lake) ; 3) black spruce bark (Rod Zone near Mallard Lake, and at Waddy Lake) ; and 4) multi-media (Tower Lake). At the latter two sites gold-bearing till is blanketed with late glacial material. Gold enrichment in the plants suggest that the roots are ab orbing gold from the underlying till. Complex processe control the uptake and retention of gold in plants. An understanding of these processes pem1its biogeochemistry to assist in locating near- urface mineralization .

Jan 1, 1986

By H. D. B. Wilson

"IntroductionRECENT ADVANCES in geo-chemistry and in •our knowledge •of crystal structure provide a key which enables us to create a systematic picture of the genesis of many ore deposits. This genetic scheme may be used with confidence in assessing certain types of orebodies and may be of some aid in actual exploration, since it affords a rational explanation of the dependence of the composition •of the ore minerals on that of the rock type in which they occur with which they -are •associated. For purposes of the present paper, .the elements chosen are •chromium, vanadium, iron, and titanium. The oxides of all these metals occur in deposits of similar or related type, and it is proposed to show that, for each, the composition of the •ore mineral is related to •the composition of the enclosing :rock, and that one of the principal factors controlling the composition of the ore is the ionic size of its constituent elements.Geochemical PrinciplesThe crystals of the rock-forming silicates and of the magmatic oxide minerals are essentially ionic types. This means that they are composed •of oppositely charged ions such as Mg²+ and 0²-, which are held together by electrostatic attraction. The ions of each element are spherical, with characteristic size known as the ionic radius. Crystals are built up by the packing of these spheres in the most stable arrangement compatible with the size and the size and valence of the ions• involved.Many of the principles governing the formation of ionic crystals are •simple ,and logical."

Jan 1, 1953