Search Documents

By H. Oterdoom, S. Pilger, T. P. Bui, J. Rotarius

"Most FeNi furnaces used to rely on post-combustion and off-gas cooling inside the furnace to eliminate the produced CO gas, and control the off gas temperature. As furnace load, capacity, and thus gas volumes increased over the years, this led to increased instabilities that can cause problems in controlling the operation. Some of the large capacity furnaces nowadays work with partial or full combustion outside the furnace, more similar to the steel industry. Forced combustion with or without enriched air and other additions can support in controlling post-combustion, stabilizing and even reducing off gas amounts, and affecting composition. This paper presents some of the possibilities and advantages of having a specially designed post-combustion system for the FeNi laterite industry, but that could also be applied to other processes as well.Large Scale Furnaces In the FeNi industry, the Rotary Kiln Electric Furnace (RKEF) process is still going strong in spite of continuous hope that hydrometallurgical processes will one day make the RKEF plant obsolete. Within the pyrometallurgical plants there is a continuous trend for larger scale furnaces. The development for a number of furnaces that were started before 1985 and increased capacity by “natural growth” is given in Figure 1. Natural growth refers to the development of the plants that after having mastered a certain level of operation, were ready for a higher load that could be installed either with a new furnace on the same site, or during a revamp. The advantages of natural growth are numerous, for example: •,Deep knowledge of the ore and its’ behavior, no need for testing, and little risk of surprises. •,Mining, laboratory, equipment, etc. is all proven technology for the conditions on site. •,Starting a furnace with increased capacity is a re-start, not a green-field commissioning. •,Typically, when increasing the production capacity of an existing plant, not the entire plant is commissioned for the first time, but only a part. In the FeNi laterite industry for example, the kilns may already have had the capacity to provide enough material."

Jan 1, 2017

By T E. Tibbetts

This paper deals with coal sampling in general and with mechanical coal sampling in particular. The necessity of obtaining representative samples is emphasized. Other sections of the paper are devoted to the design and selection of automatic samplers, with a consideration of the three main types, and the testing, operation and maintenance of these samplers. The cost of the installation of an automated sampling system must be related to the value of the material to be sampled, to the volume of coal involved, and to the savings in labour and economy which can be achieved. Introduction T HE Committee?:; on Coal Sampling of the Coal Study Subsection, Thermal Power Section (Eastern Zone), Canadian Electrical Association, was established in November, 1963, to "study the various problem areas of coal sampling." The first undertaking of the Committee was to at-tempt to survey the problem areas of coal sampling through an evaluation of coal sampling difficulties as experienced at both the plant design and operational levels within the electric utilities represented on the Committee. The results of this enquiry indicated that satisfactory answers to almost any conceivable

Jan 1, 1965

By S. A. Scott

In 1913, potash mineralization was recognized at a depth of over 7,000 feet in an oil-well hole (Norcanol's Radville No. 1 well) drilled near the town of Raddlle, Saskatchewan. Although, at this depth, potash is not considered mineable by conventional underground mining methods, this discovery shed the first light on the potash deposits of Saskatchewan in much the same manner as oil-well drilling was responsible for the first discovery of potash in the Carlsbad Basin of New Mexico in 19:25. The discovery near Radville alerted the oil-well geologists and, as a result potash mineralization was recognized in the Verbata No. 2 well, near Unity, Saskatchewan, in 1946. The mineralization, which was at a depth ?of 3,466 feet, graded more than 20 per cent K20 over a thickness of eleven feet. This discovery, as its depth, thickness and grade were all amenable to mining,

Jan 1, 1963

By K. Morin, C. -Y. Hon, G. Lachapelle

"Air-sampling results suggest drill operators working inside environmental drilling cabs at an open-pit gold mine in Nunavut, Canada, are at risk of exposure to asbestos and silica (quartz). The authors installed RESPA® CF Vortex HyperFLOW® units, which showed promising results under laboratory conditions. The goal was to evaluate the effectiveness of these units under actual working conditions. Personal and area air sampling was conducted in drilling cabs with and without the unit and a Wilcoxon rank-sum test was performed to compare the results. Particulate concentrations were significantly lower in drill cabs with a unit installed than in those without.RÉSUMÉ Selon les résultats d’une campagne d’échantillonnage de l’air, les foreurs travaillant dans des cabines de forage environnemental dans une mine d’or à ciel ouvert du Nunavut, au Canada, risquent d’être exposés à l’amiante et la silice (sous forme de quartz). Les auteurs ont installé des unités RESPA® CF Vortex HyperFLOW®, lesquelles of frent des résultats prometteurs en laboratoire. L’objectif est d’évaluer l’efficacité de ces unités dans des conditions de travail réelles. Des échantillons de l’air inhalé par le personnel et dans les aires de travail ont été évalués dans des cabines de foreuses équipées ou non de cette unité ; un test de Wilcoxon (également appelé test de la somme des rangs de Wilcoxon) a été mené afin de comparer les résultats. Les concentrations particulaires étaient considérablement plus faibles dans les cabines de foreuses équipées d’une unité que dans celles en étant dépourvues.INTRODUCTIONGenerally, mining operations are associated with a variety of occupational hazards. In an open-pit gold mine in Nunavut, Canada, drill operators are routinely exposed to asbestos (primarily amosite) and silica (quartz)—two naturally occurring substances in the ore that is to be drilled (Table 1). Inhalation is the primary route of exposure for these two hazards, which are associated with respiratory health effects such as asbestosis and silicosis, respectively. In addition, asbestos and silica are classified as human carcinogens by the International Agency for Research in Cancer (2001, 2011). Given the toxicity of these two agents, it is imperative that precautions be taken to minimize the risk of exposure of the mine’s workforce. To address this matter, the mine has an exposure-control plan, which includes the provision of personal protective equipment, personal hygiene facilities, training, and a medical surveillance program. Furthermore, the mine performs occupational exposure assessments or air sampling on a regular basis because the morphology of the ore changes rapidly with respect to asbestos and silica content."

Jan 1, 2017

By P. L. Li, B. X. Song, C. H. Wang, T. Wang, Z. Hu

"The treatment of an oxidized copper-gold ore by stage cyanide addition was investigated. For cyanidation, free cyanide ion concentration can be an indicator of whether there is copper dissolved in cyanide solution, and maintaining the free cyanide ion concentration lower than 1.0 g/L could be an effective way to prevent copper dissolution and reduce cyanide consumption. For that purpose, stage cyanide addition was introduced to control free cyanide ion concentration within the range from 0.8 to 1.0 g/L. Cyanidation tests results indicate that gold extraction was still acceptable at reduced cyanide consumption with a lower copper extraction. Based on the experimental study, industry application works at Beiya concentrator of Yunnan province, China were successfully conducted. When the raw ore contains 2.95 ppm Au and 0.75% Cu, by stage cyanide addition method, the gold extraction was still 93% at reduced cyanide consumption of 2135 g/t, which was only half of one addition method, and the copper extraction dropped to only 5%, which indicated that dissolution was prevented for almost 75% of the malachites.INTRODUCTIONCyanide with its competency to form a strong complex with gold, is the most preferable lixiviant for gold leaching. However, cyanidation is not inherently a selective process since many other minerals present in the ore are also readily soluble, especially the copper minerals. Muir (2011) reported that every 1% reactive copper present in the ore consumes about 30 kg/t NaCN, which can have detrimental effects on the process efficiency and economics due to high cyanide consumption, reduced gold leach rates and poor gold recovery."

Jan 1, 2016

By C. Mawdsley

The Tata Steel mill at Skinningrove in the North East of England produces top hat sections for mineshaft guides in sizes 102 and 150 mm. The top hat section is the technically preferred shaft guide choice for modern deep mine shafts. This paper explores the relative service performance of top hat and square hollow section guides in service. Comparative corrosion performance is reviewed and the paper describes work commissioned by Tata Steel (as Corus) undertaken by Aker Kvaerner Engineering to evaluate relative winding speeds, relative loads and fatigue life in service. The experience of supply to UK Potash mining is discussed and the future view of high capacity hoisting and larger section size market need and availability is assessed.

Aug 1, 2013

The major factors limiting the establishing of vegetation on the shale and sandstone wastes at Minto are high exchange acidity and low pH (shale pH 4-5, sandstone pH < 4). In the first revegetation program (1967-74), 3.8 million trees were planted without grading on 4,000 acres (red, jack and scots pine and black locust). White dutch and sweet clover, birds-foot trefoil and red top were established in selected areas, and ponds were stocked with brook trout. In the second phase of reclamation, beginning in 1979, a comprehensive plan will be initiated which will allow for forest production, wildlife development and recreational activities.

Jan 1, 1977

By Graham Walker

A new Code of Practice for the brake performance of off -highway vehicles was established in Alberta in 1976. Vehicles loaded to gross vehicle weight must be capable of stopping with mechanical brakes five times in quick succession on a grade of 10 per cent from a speed of 28 miles per hour. Comparative trials of various brake systems have been carried out and some combinations capable of meeting the Code are identified. Some problem areas in truck braking are reviewed and potential developments indicated.

Jan 1, 1977

By B. R. Boardman

Project Environmental Approval is a multi-faceted issue. From a mining perspective, it is a costly item because of avoidable time delay. The government perspective is that the approvals are a necessary part of meeting departmental requirements to ensure that the wellbeing of other uses of the environment is maintained. This paper outlines some of the problems inherent in the environmental approvals process and makes recommendations to both the proponent and government about improving the efficiency of the process.

Jan 1, 1978

By Victor R. Eyzaguirre

Cerro Verde is one of several large porphyry-type copper deposits in Southern Peru. The copper occurs as primary sulphides, with a significant oxide capping. The exploitation of the deposit has been correspondingly divided into two stages, the first consisting of copper production from oxides, and the second from sulphides. Minero Peru successfully started the Stage I plant in June of 1977 with the first production of electrowon copper cathodes. This paper is essentially devoted to a description of the Stage I process, which can be summarized as follows: Ore is trucked to the primary crusher, where it is crushed to 225 mm and conveyed to a coarse ore stockpile. Ore withdrawn from the stockpile is secondary crushed to 65 mm, conveyed to a truck loadout bin, loaded into trucks and driven to the leaching pads. Ore is placed on the pads in lifts and sprayed with sulphuric acid solution to dissolve the copper. Copper-bearing solution forms a pond behind a dam at the lower end of each pad and is pumped from there to the solvent extraction plant. Copper is extracted from the leach solution into an organic phase and is then stripped from the organic phase to form a purified concentrated copper solution suitable for feed to electrowinning. In electrowinning, the copper is finally recovered as cathodes suitable for sale as refined copper.

Jan 1, 1978

By Adrian Dance

The Antamina orebody is a geologically complex, polymetallic skarn located in the Peruvian Andes. A range of copper and copper-zinc ores are campaigned separately through the concentrator producing copper and zinc concentrates as well as lead and molybdenum by-products. Ore type classification at Antamina is based on chemical assays; geological or lithological variations are not considered. Consequently, each ore type demonstrates a wide range of concentrator performance. Antamina is currently implementing a system to track ore movements from the shovel face to the concentrator. Relatively sophisticated models of the ROM and coarse ore stockpiles ahead of the mill will be used to account for the variable delay between mining and milling. One of the numerous benefits of ore tracking is the ability to directly associate the measured concentrator performance with a physical location in the orebody. Using existing mine planning software, three-dimensional models can be created of such performance measures as metal recovery, concentrate quality, operating cost and reagent consumption. Such a database of information allows the true value of different ore sources to be determined. The value of an ore source is conventionally measured as metal content (individual or combined ?equivalent?) with a cut-off grade applied to indicate some base level operating cost. However, the true value of an ore source should include dynamic factors like haulage cost, reagent use, smelter penalties and even prevailing metal prices. If an ore source is considered from all perspectives rather than simply its potential to deliver value, the concept of ?ore? becomes more flexible. Any ore source that reveals itself to be unprofitable can be eliminated from the mine plan or possibly blended with others to improve its value. The ability to predict mill performance ? and thereby profitability ? is a powerful tool. In an operation such as Antamina, where managing ore sources, campaigns and the delivery of a variety of concentrates in a narrow timeline to customers is a daily challenge, prediction is the key to success and improved efficiency.

May 1, 2003

By R. E. Legg

This paper gives a brief outline of the mining and milling methods which will be used on the Stirling zinc-lead-copper ores by Stirling Mines, Limited, who have for the past two years been developing the Stirling mine in Richmond county, Nova Scotia, and who will bring the mine into production in November, 1929. No attempt has been made to give the paper a detailed technical character, for the main reason chat, since base-metal mining is something new in Nova Scotia, it is felt that a general description would be preferable before this Society, whose membership is mainly made up of chose engaged in the coal mining and associated industries. Furthermore, as both mining and milling operations will be governed to a certain degree by the experience gained after production commences, there are many points which cannot be definitely stated now. GEOLOGY Before discussing the mining methods, it is desirable to present a general picture of the geology and occurrence of the ore-bodies. The surface rocks in the vicinity of the mine consist of rhyolites of .pre-Cambrian age. These volcanic flows outcrop in very few places, usually along&apos; the beds of creeks or on the shores of the numerous small lakes. Consequently, a detailed geological map is not available. The exploration work carried out to date has revealed a sheared zone extending through the volcanic flows for a distance of over 1,000 feet. Along this zone, there has been a replacement of the rhyolites by a carbonate rock for widths varying from 50 to 230 feet, and it is in this carbonate formation chat the mineralization at a later date took place.

Jan 1, 1929

By D. T. White

Pressure acid leaching of nickel laterite ores typically involves the production of an intermediate product that is releached and refined to pure nickel and cobalt products. BHP Billiton is developing the Ravensthorpe Nickel Project to produce up to 50,000 t/y of nickel via a mixed hydroxide intermediate, which will be refined at its Queensland Nickel (QNI) Yabulu Refinery near Townsville, Queensland. The hydroxide precipitation flowsheet has been adapted to process high magnesium ores through an atmospheric leach stage, eliminate iron(III) as jarosite and oxidise iron(II) during neutralisation. The neutralisation conditions are controlled to precipitate aluminium, chromium and silicon, and to ensure good solid-liquid separation. Soluble impurities such as magnesium are purged with the tailings stream and will be managed over the long term by crystallisation in evaporation ponds.

Jan 1, 2006

By P. P. Rosario

A research project was conducted at the University of British Columbia (UBC) resulting in the development and evaluation of a novel comminution circuit incorporating autogenous grinding and parallel trains of cone crushers and high-pressure grinding rolls (HPGR). A primary driver for the circuit was to treat ore from deposits with clay and variable hardness. This paper summarizes the unique pilot-plant test program that was developed as a basis for experimental simulation and lists the main findings of the research, including the circuit?s potential operational cost savings compared to a conventional SAG circuit.

Jan 1, 2012

By S. P. Chong, N. C. Shih, G. A. Turner

Fine powders, with the bulk of the particle diameters Jess than 10 microns, were aerated so that each particle was, on the average, separated from its neighbours by 1.3 to 2 mean diameters. In this state, measurements were made of the viscosity and settling rate of the powder, and the interfacial tension between it and a moist pellet. From the viscosity measurements, qualitative analogies are drawn between the behaviour of the aerated powder and that of a dense gas near its critical point.

Jan 1, 1970

By D. J. McCulla

Mineral development and utilization affect the health of the economy and the pattern of long-term development throughout Canada. There are many diverse opinions on the contribution of minerals to the economy, but there is a dearth of adequate quantitative information. This paper discusses some recent research and provides some new information.

Jan 1, 1977

By Veerendra Singh, Y. Rama Murthy, Sunil Kumar Tripathy, Nikkam Suresh

"High intensity dry magnetic separation is commonly employed to separate different para-magnetic minerals including mineral sand. Separation in these separators is majorly influenced by the combined effect of gravity, centrifugal and magnetic forces on a particle. These separators are included in the process flow-sheets either for pre-concentration purposes or for the beneficiation of paramagnetic minerals. Separation in these separators is majorly influenced by the difference in the magnetic susceptibility of the associated minerals, particle size and shape along with the process variables of the machine. Particle size is one of the major parameter that plays an important role and decides its probability of selectivity under the magnetic field. However, effect of particle size on the performance of these separators are not well understood which is evident from the literature.In the present investigation, an effort is made to bring out the effect of particle size on particle separation in an induced roll magnetic separator while treating ilmenite fines. Effects of operating parameters, such as; magnetic field intensity, roll speed, feed rate and splitter position have been studied and their influence on particle size has been analysed in terms of yield (wt.%) to magnetic product, particle size distribution characteristics in terms of D50 and D80 size, skewness, kurtosis. Also, the particle size distribution of each test was fitted in Rosin-Rammler equation. The test results were analysed statistically to understand and quantify the influence of each variable on particle separation. It is found that, rotor speed of the separator had maximum influence on yield to the magnetic product whereas splitter position had major influence on D50 and D80 (µm) size of the product."

Jan 1, 2016

By C. S. R. Rondestvedt

In February 2010, Teck?s newest Concentrator at Mina Carmen de Andacollo (CDA), Andacollo, Chile was commissioned. The Concentrator is a single line configuration, comprising of one 36 ft diameter x 20 ft long SAG mill driven by an 18,000 hp gearless drive. The SAG mill feeds two ball mills each 25 ft in diameter x 40.5 ft long, each driven by a total of 19,000 hp through dual pinion drives. A series of four phases will be reviewed from operational readiness, mechanical completion, commissioning, and ramp-up. Also, now after 6 months of operation, this paper will review the significant steps taken during ramp-up enabling the announcement of commercial production, in October 2010.

Jan 1, 2012

By G. R. Waters

"The technology behind industrial applications such as Hydrometallurgy continues to evolve, as do the corresponding regulations and specifications that ensure the safety of workers and the environment. Valves make up key aspects of this technology, and often represent the single point of failure for entire operations. More often than not, the valves being used in Hydrometallurgy applications are known as Severe Service Valves (SSVs) due to their ability to withstand the extreme conditions. Most experts agree that SSVs are identified by applications, and that these applications are challenging to the valve’s ability to provide a minimum acceptable level of performance over a minimum acceptable duration. The Manufacturers Standardization Society (MSS) of the Valve and Fittings Industry has designated Ross Waters, President of CGIS, as Lead to the Task Force put in place to determine the minimum requirements a valve needs to be able to perform to when faced with extreme conditions, whether from pressure, temperature, toxicity, solids, or usage. This paper serves to determine what the minimum requirements are for SSVs in Hydrometallurgy applications. It will draw on five decades of industry experience from one of Canada’s leading valve experts.INTRODUCTION Severe Service Valves Severe Service Valves (SSVs) mean different things to different people. Until today, defining SSVs had little if any global agreement or recognition. That is about to change as the Manufacturers Standardization Society (MSS) has accepted an application to produce a Standard Practice so defining them. This paper provides information about the selection of SSVs in all industries but focusses on metallurgical processes and applications and offers examples to illustrate the successful and unsuccessful use of these valves. All of this with the purpose of raising the awareness of the industry on all sides, from the suppliers and manufacturers, specifiers and to the users and owners of them. It also supplies tools to understand where and why to separate SSVs from general purpose or commodity valves (GPVs). SSVs are often identified by applications, and these applications are challenging to the valve’s ability to survive. Within these applications the elements that make the service severe are being analyzed, quantified and qualified. From this, we expect to offer objective and repeatable definitions and guidance to improve the experience of SSVs, reduce unnecessary costs, provide longer service life and process runs, improve safety and reduce environmental issues."

Jan 1, 2017

By Stephen Mullowney

Outline ? Setting the stage ? Deal activity ? Q1 2013 update ? Key deal sectors ? Deals by geography ? Outlook for 2013 Key Observations 2012 ? Major retreat in M&A activity ? Glencore-Xstrata deal dwarfs all other deals ? Gold & copper dominate deal activity

May 1, 2013