Search Documents

By Prosser A. P

A computer simulation is being developed for in-situ leaching of unbroken, Zn-Pb-Ag sulphide ore. Ferric chloride is the selected reagent. Experimental work showed that a diffusion control model of the kinetic aspects was better than a surface chemical reaction control model. Entrapped reactive grains were accessible to reagent in the samples tested. Precipitated sulphur did not seriously hinder the reaction.

Jan 1, 1987

By E Villaescusa, C Drover, I Onederra

Development face destress blasting is a construction technique in deep mining, which aims to prevent, reduce the frequency, or manipulate the timing of violent, stress-driven rock mass instability at the face. This paper presents a destress blasting design concept that was optimised for the specific rock mass conditions of a deep mine using the Hybrid Stress Blasting Model (HSBM) software. The design was then implemented in an area of the mine where stress-driven instability of the face regularly occurred during development. An adjacent tunnel was constructed in parallel without destressing, within the same rock mass conditions, as a control. The rock mass response to each excavation was quantitatively compared using high-resolution local seismic monitoring. Visual observations of the fractures created by destress blasting were also made. The analysis indicated that destressing reduced both seismicity and the rock mass stiffness ahead of the face. This was inferred from the spatial broadening of the development seismogenic zone and the typically significant reduction in the spatial density of seismic events. Seismic source mechanism analysis also indicated that destress blasting generated a much wider variety of failure modes than conventional blasting. Most seismic source mechanisms following destressing were associated with natural joint structures. A relatively small portion were consistent with newly created blast-induced fractures. The greater diversity of rock mass failure modes associated with destressing implied a lower potential for stain-energy accumulation within the rock mass at the face, and thus a lower risk of hazardous instability. Observations of visible rock fracturing indicated that the major principal stress influenced the damage intensity on natural geological structures within the destressed zone, and that numerical predictions of radial fracturing limits made by HSBM analysis were realistic representations of the real blasting performance.

Nov 29, 2022

By W D. Ortlepp

Seismicity associated with deep block cave mining operations in hard rock can give rise to dynamic loading of the mining openings. A description is given of the source and damage mechanisms associated with such seismic events, and the possible demands placed on the rock support by the resulting dynamic loading. In addition, production level drifts are often subjected to large static deformations during mining. Appropriate support, able to sustain large static deformations, and capable of absorbing the energy released during dynamic loading, is described. The performance of these support types has been determined by means of large-scale dynamic loading tests, and large deformation static laboratory tests. Finally, a support system which is considered to be appropriate for extraction drifts in block cave layouts subjected to dynamic loading is described.

Jan 1, 2000

By T J. Sheer

Water vapour refrigeration (systems using water as the refrigerant) could potentially be used to provide chilled water at underground locations in mines, as an alternative to conventional refrigerators using refrigerants such as R-134a. The use of water as both the primary and secondary refrigerants is attractive in concept since direct-contact heat exchangers could be used, yielding higher coefficients of performance. The disadvantage of water is the very high specific volume of the vapour at low pressures, which leads to great challenges in compressor design, as has been reported previously in the context of slurry-ice plants for mine applications (Ophir and Koren, 1999). Steam ejectors have long been known as alternative compression devices for refrigerators, but no work has been done previously on the possibility of using ejectors powered by high-pressure water, which is readily available in mines from long pipe columns in vertical shafts. This paper presents the results of a laboratory investigation into the use of high-pressure water as the motive fluid in an ejector refrigerator. No previously reported liquid ejector system has achieved subcooling of the process fluid, ie a reduction in fluid temperature within the evaporator to a level below that of the motive fluid. In contrast, the present work demonstrated that subcooling could occur at motive water pressures above 5 MPa. Mine cooling applications were considered and it was concluded that while this concept would not be feasible as a mine-wide cooling source, there could be specialised applications where it would be beneficial. One application would be to cool backfill and thereby reduce the heat load at the working face. In this case the best performance would be achieved by using the ejector in combination with an energy recovery system such as a Pelton turbine or a three-chamber pipe feeder.

Jan 1, 2005

By B Bendtsen, L McQueen

The use of shotcrete as an efficient means of both temporary and permanent ground support has continued to grow over the last 30 years, with its use underground now commonplace around the world. However, the development of analytical design methods has lagged advances in material and application technologies. Historically, part of the reason for this was a lack of understanding of how shotcrete linings actually worked. Considerable progress has been made in this area in recent years and this paper attempts to summarise the current state of practice with respect to shotcrete lining design. It then concludes by summarising areas where the authors consider future research and development is still required.

Jan 1, 2008

By J Gutzmer

The Kalahari Manganese Deposit in South Africa accounts for 80 per cent of the worldÆs land-based mineable Mn reserves. Although the ores are primarily mined for export, South Africa is the worldÆs third largest producer of ferromanganese and ferrosilicomanganese alloy, both of which are derived from the smelting of these ores. Mineralogical analysis has traditionally been forsaken for bulk chemical assaying in quality control of smelter feeds, principally because quantitative data could not be easily produced. Yet, mineralogy plays a vital role in determining smelting behaviour, which in turn has economic implications when aspects such as energy and reductant consumption are considered. Smelting is an endothermic process, and the amount of energy input required is dependent on the minerals present in the ore, as well as their relative proportions. Further, knowing the bulk Mn oxidation state in the ores allows for calculation of the amount of oxygen that must be driven off to produce alloy, and hence the amount of reductant required. Additionally, certain minerals can be correlated with potentially deleterious elements, so that ore mineralogy can indicate penalty element distribution. Mineral abundance analysis was conducted on ores from the Kalahari Manganese Deposit using quantitative X-ray powder diffraction. Rietveld refinement using a fundamental parameters approach was applied to micronised ore samples. The mineral percentages obtained were validated using mineral chemical data together with bulk major element data derived from ICP-OES. Bulk oxidation state partitioning was then carried out knowing the Mn valence in the minerals. The results show potential for implementation of the proposed method on a smelting plant, where ore blending could be then implemented to achieve consistent feed compositions to smelters. Selective mining could also be undertaken to obtain desirable ore compositions for domestic or international markets.

Jan 1, 2008

The paper explains the genesis of the Ballarat College of Advanced Education to its unique position in mining engineering education. A description follows of the development of the Graduate Diploma in Occupational Hazard Management which commenced in 1979 in the cooperative mode of four groups of three weeks full- time study followed by twenty-three weeks in industry. In particular an analysis will be given of the state of origin of students, ages and employing industries. Given the experience from the evolution of this course a similar process is described for the Graduate Diploma in Mining which has been accredited to commence early in 1987.

Jan 1, 1986

By Paine G. G

The measurement of the fragmentation size distribution of a blast muckpile can be achieved directly by screening the entire muckpile. Screening of muckpiles in a production operation is generally not practical due to the logistics and time involved moving large volumes of rock through a screening plant. An indirect technique to assess blast fragmentation size distributions has been developed. This technique uses photographs of the blast muckpile taken at intervals during the excavation cycle. The images from the photographs are input to desktop computer software via a digitiser tablet. The software compilates the rock fragment sizes and calculates a size distribution. This paper discusses the technique and subsequent data analysis. Examples of the application of this technique for the assessment of comparative blast performance are given.

Jan 1, 1990

By D Wallace, H Guo, B Shen

Appropriate management of the ground subsidence induced by coal mining activities is essential. To assess the effectiveness of grout injection for mining subsidence control, time-lapse ground penetrating radar (GPR) imaging data were collected before and after grouting. The pregouting subsurface responses were interpreted to have changed after grout injection. The changes were caused by injecting the grout materials (flyash and water) into the delaminated strata and permeable fracture zones. The largest distance of the observed GPR event changes at the right end of the main profile is 132 m away from the injection borehole. Although the GPR images could not easily tell if the image changes were caused by the injected ashes or the water, it does suggest that the injection materials had been pushed at least 130 m away from the injection borehole. This is consistent with the borehole scan monitoring, which confirmed that the grout has travelled more than 90 m from the injection borehole.

Jan 1, 2006

By M Ujihira, M Komazaki, K Higuchi, D F

A diesel engine with a misfiring cylinder is likely to break down in a short time when the engine is used without maintenance. The authors have developed a method of detecting the occurrence of cylinder misfiring and specifying the misfiring cylinder by using wavelet analysis and statistical analysis on the root mean square (r.m.s.) values of two kinds of acceleration waveforms. This detection method is considered superior to traditional methods, which require several accelerometers, especially in terms of simplicity. Since the development of the method, research has been conducted on semi-automatic processing of measured signals and signal transmission from the worksite to a remote office. Field tests confirmed that 1 + 105 points of dynamic data could be transmitted through the mobile multimedia network within 15 minutes, and the time for signal processing was within 15 minutes. Final determination on the condition of a diesel engine in heavy machinery could be achieved within 30 minutes. Shortened processing time is expected by improvement of the processing software.

Jan 1, 2003

By R Buerger, D Barrett, P Hodkiewicz

The Emily Ann nickel mine is owned and operated by LionOre Mining International Ltd. The deposit was discovered during 1997 and is blind, concealed beneath 25 m of transported cover and a further 100 m of unmineralised Archaean felsic rocks. Nickel sulfide mineralisation is hosted predominantly in strongly deformed, altered and metamorphosed Archaean komatiitic ultramafic rocks. Subordinate felsic-hosted, remobilised mineralisation is also present. Mining of ore commenced during late-2001. Since the early days of exploration drilling, through feasibility delineation drilling and subsequent mining, a geological model involving thrusting and folding of a komatiitic-hosted nickel sulfide deposit has been an evolving theme. Development of appropriate mine geology procedures, including detailed mapping, significantly increased the confidence of mine-site geology and engineering staff in the geological model and improved operational efficiencies during start-up. This also allowed the engineering and mining team to develop a tolerance for the large fluctuations in daily production grade, with an understanding that budgeted production targets, on a level-by-level basis, were achievable. This paper describes the development of the current interpretation of the deposit and emphasises the importance of a sound understanding of deposit geology. The direct benefits at Emily Ann included improvements in drill targeting, resource estimation and mine planning.

Jan 1, 2003

This paper reviews an analytical model that defines the relationship of weight-weighted or volume-weighted average haulage distance with bench height and other related parameters; presents the optimum bench heights under various conditions in terms of minimising the weighted average haulage distance of ore/waste during the full lifetime of an open pit mine, and discusses the truck-haulage economics of mining open pits by high bench, specifically by 15 m, 18 m and 20 m bench through marginal analysis. The observations from these analyses disprove the previous conflicting assertions that the overall weighted average haulage distance either increases or decreases monotonically with bench height. It is concluded that: (i) an increase of bench height to 15 m from 12 m is likely to be viable under the general conditions of large-scale deep open-pit mines; (ii) the reduction of haulage cost is limited with the case of increasing bench height to 18 m from 15 m; and (iii) the feasibility of mining open pits by 20 m benches is generally questionable. These conclusions may serve as a useful guide for those who advocate open pit mining by high benches.

Jan 1, 1995

By Soldenhoff K, Levins D, Collier D, Day A, Secomb R, Brown S, Tapsell G, Bellingham A, Quan C

Bench and pilot plant studies were carried out at ANSTO to develop a process for rare earth recovery from the Mt Weld deposit near Laverton, Western Australia. This paper describes the development of the flowsheet, which is similar to conventional monazite processing, but with the introduction of several innovative steps to account for the complex rare earth mineralisation and the presence of specific gangue minerals. A unique feature of the flowsheet is the recovery of cerium by solvent extraction from a sulphate leach liquor. The process was tested continuously by the operation of a pilot plant at ANSTO's Lucas Heights Research Laboratories, Sydney in the first half of 1992. The plant, designed to treat 100 kg per day of beneficiated ore, confirmed the viability of the process, with rare earth products from the operation satisfying stringent buyer specifications.

Jan 1, 1993

By Moxon NT, Torrace AC

The detonation pressure of an explosive is a function of its density and its velocity of detonation (VOD) and relates directly to the degree and manner in which the explosive loads the surrounding rock. The suitabil- ity of an explosive to any particular situation is determined not so much by the total energy released but more by the rate at which it is released. As the science of rock blasting advances it is becoming economically more important to quantify explosive performance, particularly with respect to quality control and fragmentation. As part of a major explosive user, BHP Central Research Laboratories have developed a number of tech- niques to determine the detonation characteristics of explosives. These include a method of continuous velocity of detonation measurement based on the SLIFER principle. This not only enables the VOD of the explo- sive to be determined, but also has the versatility to allow factors such as under priming, slow run up, the effect of water, variable energy load- ing and the velocity of the shock wave in the stemming to be assessed. Multi point VOD systems have also been developed for more routine appli- cations. With a minor modification they can be used to determine the absolute delay of detonators accurately and economically. Direct deto- nation pressure measurement methods have also been developed based on piezoresistive techniques. Future developments include the incorpo- ration of all the above techniques into a single, portable package, allow- ing easy use on the mine site.

Jan 1, 1988

By Jacobs M

After a methane explosion in a coal mine a pre-determined crisis management procedure is instigated. As the process rapidly evolves the inevitable question arises - are personnel trapped underground, are they alive and can they be rescued without putting the lives of the rescue crew at risk? This is a very emotive question with many sub-questions such as; could anybody have survived, is there the potential for a secondary explosion and is there a `window of opportunity' before that secondary explosion occurs?To determine if that window of opportunity exists two fundamental elements must be in place; a method of determining the atmosphere at key points in the mine and a method of predicting the course of change of that atmosphere with respect to time. The first element can be achieved if the tube bundle system is intact and drawing samples from known points, alternatively boreholes can be drilled from the surface. The second element can be realised by utilising a sequence of computer generated control charts which have a time axis, a percentage combustibles axis, the upper and lower explosive limits of the current atmosphere and a prediction option which allows the user to look at the potential changes in the atmosphere over a set period of time. These control charts would be part of the mines on-going crisis management system rather than a tool to be used after an explosion had occurred.

Jan 1, 1998

By D Newton

The Mt Morgan Minesite in Central Queensland has been subject to both underground and surface gold mining operations since the late-1800s. The site is largely unrehabilitated and poor quality surface run-off and subsurface leachate is contaminating the nearby Dee River. The site is dominated by a large open cut, which now stores contaminated surface and subsurface run-off. Three models were used to simulate the complex hydrologic processes occurring at the Mt Morgan Mine: a rainfall-run-off model, a groundwater model and a storage behavioural model. Study results showed that the open cut is filling with water and will soon spill large volumes of highly polluted water to the Dee River on a regular basis if no remedial action is taken. This will result in a three-fold increase in pollutant load to the Dee River. Based on a consideration of water quality and quantity it was concluded that the first priority for future minesite water management should be the prevention of spills from the open cut. Potential management options to achieve this objective included surface rehabilitation, catchment diversions, modification of the pump-back system and controlled releases to the Dee River during floods. However, assessing the relative effectiveness of these measures required a thorough understanding of the complex surface and subsurface hydrology of the site. The results of a 100 year simulation of hydrologic processes revealed that previously favoured management options would be ineffective in preventing spills to the river. On this basis, a continuous treat and release strategy was proposed as the only reliable method of preventing future spills. The results of this study demonstrate that good environmental management decisions must be based on an understanding of the relevant physical processes and consideration of cumulative effects over an appropriate time scale.

Jan 1, 2003

By D La Rosa, W Valery, A Jankovic, S Ese

Metso Minerals Process Technology Asia-Pacific (MMPT-AP) has been working with many mining companies worldwide performing æMine to MillÆ or Process Integration and Optimisation (PIO) studies. MMPT-AP has developed a proven methodology to improve the efficiency of the mine-mill interface and gain maximum benefit. The PIO methodology involves rock characterisation, mathematical modelling and simulation to generate a list of operational and control changes for both the mine and concentrator. Following the methodology, the list of recommendations is developed relatively easily; the more challenging part depends on the company. Success of a PIO project relies on the ability of an organisation to implement change û both operationally and culturally: the human element. When a PIO project is started, there is initial interest and commitment from the company. But how can this be maintained? How does an operation know if the benefit continues? MMPT-AP is now developing long-term relationships with clients to ensure that the increased production and improved efficiency continues. Direct and indirect measurements are used to determine the key factors involved and to understand the cause/effect relationships. Simulation tools also can be used to compare current with recommended practices û so when material properties vary over time, the benefits can still be quantified. PIO is about empowerment: by measuring and understanding what parameters affect concentrator performance, the site personnel now have the knowledge to make a difference. Rather than simply reporting variable or poor concentrator performance, operations can predict when production will be affected and put controls in place to prevent it from happening. This requires support and commitment from the company or æbuy inÆ. Ensuring this buy in continues is the challenge facing every company involved in PIO work û but the benefits are well worth it. This paper will review MMPT-APÆs experiences in implementing PIO projects in the long term: from both the consulting and operational viewpoints. MMPT-APÆs involvement with a number of companies will be discussed as examples of what works and what does not.

Jan 1, 2007

By M Dorricott

This paper describes the design, construction and performance of sill pillars using cemented development mullock at the Crusader Gold Mine. The orebody is some 35 m - 60 m in length, 5 m - 8 m wide, dipping at 60¦ - 85¦ and plunging at about 40¦ to the north. It is accessed via a footwall decline. The ore occurs at the contact between basalt and ultramafic. This contact is characterised by shearing and alteration; and is prone to unraveling failure. The cut and fill mining method at Crusader extracts 25 m high ore blocks in four flat back lifts and one 8 m thick crown pillar. To enable full recovery of these high-grade crown pillars with minimal dilution, a 5 m thick sill pillar is constructed using cemented rock fill (CRF), after mining of the bottom two lifts in each block. Uncemented development mullock is used as rock fill (RF) for subsequent lifts. Development mullock and cement/water slurry is mixed underground to produce CRF. The fill is transported to the stope in LHDs and dumped on the floor. The sill pillar is advanced progressively, with compaction provided by the loader driving over the previously placed fill. Old jumbo rods are installed as shear pins along the flat dipping hangingwall to reduce the risk of rotational failure of the pillar. A fan of cable bolts is installed into the hangingwall to prevent unraveling failure in the sheared ground. Buffer blasting is used to minimise damage to the CRF sill pillar when the crown pillar below is extracted. At the time of writing, extraction of the crown pillar underneath the CRF has taken place at the 930 stope. The crown pillar was extracted successfully with dilution from the backfill and hangingwall minimised and 98 per cent of the gold recovered. This compares with pillars that were mined beneath uncemented backfill where only 70 per cent of the gold was recovered and where there was significant dilution from the backfill and from hangingwall failures. Where no CRF was placed, there were also numerous production delays caused by large rocks from the hangingwall blocking the stope brow.

Jan 1, 2002

By Lawrie DC

Finely ground beryl was decomposed by mixing with ground limestone and soda ash andheating at 900¦C for,4-6, hours.The sintered material was then crushed and leached by boiling under reflux with 5N sulphuric acid for up to 4 hours. The liquor containing Be, ; Al, . Fe and, other elements as sulphates, was separated from the residue which consisted mainly of silica and gypsum, either' by filtration or by decantation washing.The clarified leach liquor.was first treated to remove Fed}: , by contacting with a primary amine-kerosene solution in2 counter-current stages. The iron free liquor wa,s then passed to a 4-stage counter-current extraction unit where it was con-tacted with 0.5M di-(2 ethyl hexyl), phosphoric acid (EHPA) in kerosene. The'operating conditions were such that at least 99 p'br cent of the Be and only 7' per' cent of the Al- was, extracted The ,B6`= and. Al were ;stripped from the organic phase by sod-ium hydroxide solution of suitable concentration to form soluble "beryllate" and "aluminate" respectively. Most of the Be was subsequently precipTitated a's Bo(OH)2 by-hoating the alkaline solution to 90C, the Al remaining in solution. After filtra-tion and washing, the Bo(OH)2 could be ignited directly to BeO at about 1000 C or used as a feed to further purification stages aimed at producing "nuclear grade" BeO.A small coaAter-current extraction unit was operated con-tinuously using liquor derived from the sintering and leaching stages. Data obtained in batch laboratory tests were confirmed. A product obtained by ignition of the washed "beryllate" precip-itate contained more than'99 per cent BeO.

Jan 1, 1963

By R Brake

The Enterprise Mine Project (EMP) is being developed by Mount IsaMines Limited as the future source of copper ore at the Mt Isa miningand processing complex. Environmental engineering is one of the majortechnical challenges facing the project because of the depth of theorebodies, high virgin rock temperatures and hot ambient surfacetemperatures in summer. This paper discusses the engineering principles adopted by EMP to manage the risks associated with working in these adverse thermal conditions.

Jan 1, 1998