Search Documents

By Moorrees C

Tests show how that temperature and rate of sparging to remove carbon dioxide determine the rate of precipitation and the chemical and physical properties of hydrated magnesium carbonates precipitated from clarified magnesium bicarbonate liquors derived from crude magnesia. At temperatures above 55°C the product is largely in the form ofhydromagnesite, Mg5(C03)4(OH)2.4H2O Between I5°C and 55°C the major product is nesquehonite, MgCO3·3H2O, although partial hydromagnesite precipitation can be induced by a high rate of aeration.As a result of the reduced time required to bring about greater than 95 per cent magnesium precipitation, the higher MgO content of the product, the ease of product recovery from the precipitation vessel, and the lower energy requirement for thermal decomposition of the precipitate to magnesia, it is preferable to precipitate hydromagnesite rather than nesquehonite. Moreover, the magnesia produced from hydromagnesite is somewhat more reactive than that formed from nesquehonite.Using precipitate calcination temperatures less than 1000°C, the chemical reactivities of the magnesias formed from both precipitates are greater than those of the crude magnesias derived from Savage River magnesite itself. The magnesias would be suitable for most uses developed for caustic-calcined magnesia. However, for refractory brick manufacture, it would be necessary to briquelle the caustic-calcined magnesia. adjust the CaO and SiO2 contents and sinter at temperatures in excess of 1600°C. This would bring about an increase in the bulk density and induce the appropriate chemical bonding reactions.Dead-burned magnesia produced from Savage River magnesite by the calcination/carbon dioxide route would have very low B2O3 contents, typically less than 0.0001 per cent.

Jan 1, 1985

By A R. Gerson

Pyrite, chalcopyrite and mixed sulfide samples, with and without quartz (5 wt per cent S), were subjected to column leaching to mimic natural weathering (cyclic wetting and drying). The pH and SO4 2- concentration of the column effluent was measured over a period of 78 weeks. The pH of the pyrite-only containing column rapidly decreased and remained under pH 4 after 12 weeks of leaching. The pH calculated assuming a 2:1 ratio of H + generation and SO4 2- release was slightly lower than that measured. However, a reduced H + to SO4 2- ratio of 1:1 is predicted if the release of aqueous Fe 2+ is assumed rather than the formation of Fe(OH)3. The pH of all columns containing only chalcopyrite or a 1:1 mole ratio of chalcopyrite and pyrite remained at or above pH 5 for the duration of the leach even though significant SO4 2- was released. One column containing the same initial surface area of pyrite and chalcopyrite but only approximately 0.10 the mole fraction of S as chalcopyrite maintained a pH of greater than five for the first 56 weeks of leaching and showed sporadic acid production thereafter. It is well established that oxidation of chalcopyrite results in a surface layer of polysulfide material. It is the formation of polysulfide that neutralises the acid produced on S oxidation through to SO4 2-. Hence where polysulfide formation occurs extensively on chalcopyrite the resulting solution pH decrease will be less than that based on SO4 2- production. The oxidation rate of sulfide minerals increases with decreasing pH and hence acid formation via sulfide oxidation to SO4 2- causes the subsequent oxidation rate to increase. The addition of calcite (CaCO3)to a pyrite column not only neutralises the acid formed but also decreases the rate of release of sulfate to solution by a factor of approximately 30. This is also the case where chalcopyrite is present mixed with pyrite. The rate of release of sulfate from the mixed sulfide mineral columns (after the initial release of the sulfate already present) was between one-fifth and one-tenth that in the absence of chalcopyrite.

Jan 1, 2003

Mine haul road design at Bougainville Copper Limited has undergone significant changes since mine start-up. Selection of 95 tonne trucks and the subsequent replacement by 155 tonne units is discussed, with particular reference to haul conditions within the mine. Changes to haul road design and construction practices are detailed which have lead to improved standards and tyre life. INTRODUCTION Bougainville Copper Limited operates one of the largest copper mines in the world at Panguna, Bougainville Island, in the North Solomons group of Papua New Guinea. The mine commenced commercial operation in April, 1972 and current planned production is 198 000 tonnes of material per day, of which 115 000 tonnes is ore averaging 0.46% copper. Annual total planned production is 72 000 000 tonnes to yield approximately 150 000 tonnes of copper with significant quantities of gold and silver. The mine operations workforce now consists of national employees up to General Foreman level.

Jan 1, 1982

By N Tuffs, R Peace, S Xue

Mine gas control is a major issue in most of the gassy underground coal mines, due to its direct impact on safety, production delays and cost of production. Analysis of the gas data, from different collieries in Australia showed that longwall gas emissions have increased substantially over the years. Simply increasing the number of goaf holes in the panel or decreasing goaf hole spacing seems not to be effective, in controlling high goaf gas emissions. A major research project has been undertaken by CSIRO in collaboration with mine sites to address this goaf gas control issue with the aim of developing effective and optimum goaf gas drainage strategies. The project has combined extensive field studies with computational fluid dynamics (CFD) models, to characterise goaf gas flow patterns and develop effective gas control strategies. The research work specifically involved review of gas control issues at field sites, goaf gas monitoring, tracer gas tests, CFD simulations and extensive field trials. Field demonstration studies of the new optimum strategies have been conducted at two collieries in Australia. The project results have shown that the optimum strategies were highly successful, in improving the overall efficiency of goaf gas drainage systems, at both the field sites. Results of the goaf gas flow characterisation studies and field demonstration studies are summarised in this paper.

Jan 1, 2005

By Koppe JC, Strieder AJ

The Rivera Crystalline Island (RCI) is an erosional window of the intracontinental Parana Basin that outcrops in the Rivera Department, north of Uruguay. RCI is made up mainly by Precambrian granites, metasediments and granite-gneisses. This island is crosscut by a dextral transcurrent shear zone system, the Rivera Shear System (RSS). The bulk strain ellipsoid was defined by previous work and has allowed the evaluation of shear dynamics. The geometry of the shear system is made up of two shear directions: E-W (P-shear), which turn right to NW-SE direction (R-shear), leading to the development of extensional bends. The shear zone system was developed in brittle-ductile to brittle regimes, under temperature conditions compatible with greenschist facies metamorphism. The shear zones are marked by an intensive fracture cleavage development. Mylonites develop only in narrow, discontinuous higher strain zones. Internally, the shear zones are dominated by intrusive rocks, mainly granites, dacites and diorites. Hydrothermal alteration has been developed in several areas.The economic significance of RCI is given by several small gold deposits, which have been exploited since 1869. One major new gold mine is under development, the San Gregorio Gold Mine. This gold deposit is locally controlled by a dilatant site where R-shear turns right to P-shear. Mine lithologies were deeply altered by hydrothermal fluids in the dilatant structure. This work presents the lineament-structural analysis carried out to identify similar structural patterns in all RCI sites favourable to host other gold deposits. The exploration program also considered remote sensing, geology, geophysical and geochemical survey.

Jan 1, 1997

By P Khalkho, M Singh

Rock masses when subjected to uniaxial or triaxial cyclic loading (eg in hydraulic running tunnels, during retrieval and injection of oil and gas from storage underground caverns and haulage roads), the material has a tendency to fail in fatigue. In order to design safe and reliable underground structures, the determination of brittleness under such loading conditions becomes a pre-requisite. Brittleness influences strongly the failure process and makes the rock mass behaviour complex under different tunnelling and mining activities. Brittleness Index is a term to quantify the brittleness feature of a specimen. In the present study, an attempt has been made to quantify the brittleness of jointed specimens using different brittleness criteria. The joints of the model jointed specimens were oriented at an angle of θ=15° normal to the loading direction, each having three different JRC’s=2–4, 12–14 and 14–16. The specimens were tested under triaxial conditions in incremental complete cyclic test scheme performed at displacement-controlled mode. Different brittleness criteria were used ie stress-strain dependent brittleness index, Young Modulus approach and energy-balance based mechanism. It was observed that energy-balance based mechanism which consider the post failure behaviour is more descriptive to reflect the whole variation of brittleness from sheer brittleness to ductility.

Nov 29, 2022

By K Ehrig

Two irrefutable facts in geology and metallurgy are: ore deposits are comprised of variable mixtures of minerals which are systematically distributed throughout the deposit, and mineralogy exerts the primary control on metallurgical performance. If the distribution of process critical minerals can be quantified and mapped, then a logical assumption is that metallurgical performance can be predicted across the deposit.Olympic Dam is a +9 billion tonne Fe-oxide Cu-U-Au-Ag deposit which is hosted entirely within a magmatic-hydrothermal breccia complex consisting of over seventy ore and gangue minerals. Each has a unique set of metallurgical performance properties. Fortunately, 15 of the 70 minerals accounts for >98 per cent of the total rock mass.The mineral mapping journey commenced in the early drilling days shortly after the discovery of Olympic Dam in 1975. Geologists quickly recognised that the copper-iron sulphides had a predictable zoned distribution. However, geological models reflected the presence or relative abundances, not quantitative concentrations, of the minerals. This type of mineral mapping remained relatively unchanged for ~20 years and was of limited use outside of geology.Several things changed during the mid-1990s: assaying costs decreased significantly, instruments capable of automatically measuring mineralogy became readily available, the recognition of two quantifiable relationships at OD (ie mineralogy is a function of chemical composition (ie assays), and metallurgical performance is a function of assays, mineralogy, texture and process conditions. The linkage of metallurgical performance to mineralogy and mineralogy back to assays allows for every assayed sample in the resource model to be assigned mineral concentrations and metallurgical performance predictors. At Olympic Dam, block models (ie 3D maps) are routinely produced for 27 elements, density, 15 process critical minerals and greater than 50 metallurgical performance variables. These geometallurgy-enabled resource models are used for mine planning, process plant design and process optimisation studies. *This is an abstract only. No paper was prepared for this abstract.*

Sep 5, 2011

By D E. Tennant

In the fields of geotechnical engineering and slope management, various software packages are used to assess the behaviour or propensity for a slope to fail. Traditional kinematic analysis calculates the probability of failure of design sectors with respect to dominant structural set orientations. A novel methodology is provided here to view potential hazardous slope behaviour in 3D, allowing engineers to make informed decisions regarding various pit slope geometries. Apparent dips are calculated for every point in space with respect to every slope orientation of the entire pit surface/design, specifically in reference to bench and inter-ramp planar failure mechanisms. Implementing a proactive approach to slope design will not only lead to early mitigation of risk but can also add direct value by enhancing or improving upon slope angles for earlier access to ore. From a safety perspective, identification of unfavourably oriented slope geometries can be dealt with before failure occurs. This methodology relies on a strong understanding of the existing rock mass anisotropy, particularly behind the face, thereby removing some of the uncertainty surrounding pit design as well as presenting engineers with an additional means to manage risk.

Nov 29, 2022

Australian coal mines have spent considerable capital on dragline improvements over the last two years. This has included ~$30 M on UDD conversions, >$20 M on new buckets, boom upgrades, electrical upgrades, etc. This is a natural part of the response of mining companies to technology and replacement programs. Capital expenditure is a normal part of the ongoing success of most companies. There is however, a tendency for some people to rely on the capital alone to provide the ongoing improvements in equipment productivity. Implementing new technology through capital expenditure is only part of the equation in continuous improvement. For 80 - 90 per cent of the year, the operator controls the productivity achieved by the dragline. Variation between operators is huge. The average standard deviation in productivity is 12 per cent and maintenance impact is over 40 per cent. Robbins 2003, states: Contrary to what we were taught in grade school, we werenÆt all created equal. Most of us are to the left of the median on some normally distributed ability curve. Further, he states: The issue is knowing how people differ in abilities and using that knowledge to increase the likelihood that an employee will perform his or her job well. There are two options for reducing variability between operators; improving operator ability and getting the machine to take over what the operator is doing (automation). Dragline automation will be discussed, however, this paper will focus more on the æhuman factorÆ and how to establish a dragline with minimum variability between operators.

Jan 1, 2005

By E S. Souza, H Delboni Jr, M F. Calixto

This paper aims at presenting the results of laboratory, pilot plant and simulation studies for the design of the grinding circuit for the beneficiation of compact itabirites from the Conceitpo mine. Two alternatives were investigated, both utilising the current crushing circuit up to tertiary crushing. Under alternative #1, quaternary crushing was considered to produce the feed of the ball mill; under alternative #2, high pressure grinding rolls were selected to prepare the ball mill circuit feed. Pilot scale studies pointed towards the use of high pressure grinding rolls (HPGR). The circuit design was based on a throughput of 720 t/h, representing a nominal solids flow rate of 600 t/h, considering a design factor of 1.2, and P80 of 95 ¦m.

Jan 1, 2007

By H W. Scriba

The development and improvement of computer-based process simulation packages over the past 20 years has provided process engineers with a powerful tool to use in the design of complex metallurgical plants. The use of such modelling tools has enabled the design of process plants that minimise operating and capital costs whilst optimising plant efficiency and recovery. Almost every new project developed in the current market is underpinned by a simulation of the process. In line with engineering best practice this simulation should be based on laboratory/pilot plant test work results and sound assumptions. Any errors that are not identified in the development of the process simulation may have significant effects on the final design and operation of the processing plant. Developing a simulation of the process in a comprehensive, logical and auditable manner is thus essential in ensuring the simulation accurately represents the expected process plant behaviour. A methodology that ensures these requirements are met has been developed by SNC-Lavalin Australia and is described in this paper. The methodology includes the major review stages of data collection, model planning, model building and optimisation, model review, scenario testing and options development, and model reporting. All of these stages should incorporate comprehensive client interaction and review by a suitably qualified representative. In applying these methodologies SNC-Lavalin Australia ensures that the process simulation model developed can be confidently utilised in the design of the process plant, and in the estimation of operating and capital costs, whilst ensuring that engineering best practices are met.

Jan 1, 2008

By OÆNeil G. R

The gold adsorption capacity of ash-char and ion exchange resin Zerolit F.F. (I.P.) was evaluated by obtaining Freundlich isotherms in the presence of selected variables. It was found that the presence of Na , 2+, Ca 2+ cations and SO4 , CN , S Z, 0 2- Zn anions prompted adsorption of gold onto the char and reduced gold adsorption capacity of the resin. Temperature, particle size of adsorbent and pH of solution were found to influence the gold adsorption capacity of char and the resin. The most efficient desorbent for gold adsorbed on the ash char was S2 ions. Optimum sulphide concentrations were found in the region of 1% Na2S. Investigation into the concentration of gold from actual carbon contaminated gold residue dumps in Kalgoorlie area onto ion ex- change resin showed limited success in one case and not so in another. Maximum gold adsorption by the resin appeared when cyanidation and sulphidization treatments were carried out simultaneously in the presence of the resin.

Jan 1, 1979

By Ricketts N. J, Smith G. D J

A hydrometallurgical process was developed for recovery of copper from copper-lead matte formed as an intermediate product at the BHAS lead smelter at Port Pirie. A plant utilizing this process was commissioned in 1984. The leach step involves oxidation of the copper-lead matte in an oxygenated acidic chloride-sulphate leachant. The results of laboratory scale testwork from which the chemistry of leaching was deduced, are presented in this paper. The rate of recovery of copper to solution from copper-lead matte depends largely_on the availability of oxygen to the sulphide surface. The optimum leach temperature is approximately 85¦C. Free acid must be supplied according to the stoichiometry of the leach reaction: Cu1.91 S + PbS + 2.91 H2SO4 + 1.455 02 = 1.91 Cu2+ + 1.91 SOj- + PbSO4(s) + 2.91 H2O + S¦ The grind size of the matte is of minor significance. Chloride concentration in leachant should be at or above a minimum of 10.0 g/l. Chloride acts to complex cuprous ions formed during leaching.

Jan 1, 1987

By P Audet, D R. Mulligan, D Doley

This analysis attempts to reconcile existing ecological theories, rehabilitation planning goals and implementation constraints in the form of a rehabilitation paradigm that considers potential and pragmatic ecosystem transformation pathways. The framework prioritises multiple developmental scenarios for post-disturbed landscapes within a continuum of ecological outcomes. A feature of the framework is that ænovelÆ ecosystems and agro-ecosystems, having a range of commercial and societal values, are valid outcomes spanning the conceptual divide between the ecological functions of under-rehabilitated versus re-instated ænaturalÆ landscapes, especially in a changing environment. Landscape suitability analyses are considered to be fundamental to the incorporation of regional landscape and climate in the implementation of land rehabilitation and management strategies. Altogether, the paradigm could facilitate the identification of widely pertinent rehabilitation goals having direct implications at the regional scale of restoration ecology and acceptance of the need for ongoing commitment to the management of disturbed environments.CITATION:Audet, P, Doley, D and Mulligan, D R, 2012. Can ænovelÆ ecosystems offer suitable rehabilitation alternatives for post-mined landscapes?, in Proceedings Life-of-Mine 2012 , pp 135-142 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By A Gibbs

Culture and leadership go hand in hand, especially when it comes to investing in safety. But the reality is that most safety leaders haven’t been taught the fundamental soft skills needed to lead effectively. In fact, only one in four safety leaders demonstrate effective skills and behaviours. Furthermore, when compared to its peers in other high-risk industries, our research indicates mining has the most room for improvement when it comes to effective safety leadership. In this presentation safety culture, climate and leadership will be outlined. Additionally, research data collected from our clients, across a variety of industries, will be shared to inspire reflection on the value of safety leadership. Finally, strategies to empower leaders and increase safety leadership behaviours will be described.

May 5, 2022

By J Green, R Bartlett, A Goldstone, D Ferguson

Solid Energy New Zealand is developing an extension of its Rotowaro open cast coal mine near Huntly. This large 8 year, 11 million tonne opencast coal mine, referred to as the Awaroa Project, is fundamental to Solid Energy's medium term business strategy and meets its open pit coal resource needs while further resources are developed for the long term. Equally importantly the project is also fundamental to meeting New Zealand's energy requirements in the face of growing demands, a dwindling gas resource, and dry winters creating hydropower shortages. This project with its national significance in the current energy climate, its significance to Solid Energy as a business and its significant size has been consented against a backdrop of criticism of the Resource Management Act and the introduction of the 2003 amendment to the Act. As is common practice for this type of project Solid Energy conducted a significant technical programme in order to complete a comprehensive assessment of environmental effects. Solid Energy also has an active programme of community and interested party consultation and this programme formed the basis for project based consultation with local residents, regulatory bodies and iwi. As a result of the approach taken the environmental effects of the project were shown to be no more than minor and Environment Waikato considered that the project should be processed under the limited notification provisions of the RMA amendment. The project was processed under RMA quickly and efficiently and consents were granted within 6 months of lodgement. The RMA and its 2003 amendment provided a good framework for dealing with this project and did not impede the process of development of this important energy resource.

Jan 1, 2004

By D M R Stone

Failings di,posal presents many challenges at metal mines in Peru where the extreme relief yields very little useable land area. These challenges are amplified by other hazards such as the high seismic environment, high rainfall, and frequent debris torrents down the steep hillsides. As a result many mining operations have resorted to in-river disposal of mill tailings. This paper presents a case history of one underground metal mine located in the high Andes mountains of Peru where in-river disposal of tailings has been used for some 30 years. The paper outlines a comprehensive engineering study that was aimed at increasing the utilisation of tailings disposal underground. The scope of this study included modifications to the grinding and flotation circuits to produce a high sulphide and low sulphide tailings for underground and surface disposal respectively: mapping and cataloguing of abandoned stopes for hackfilling: modifications to the existing backfill system to improve icliahility and throughput, and a preliminary evaluation of alternatives Such as silicated and paste fills.

Jan 1, 1998

By White A, Price G

The main assets of a mining company are its orebodies; the second are the people who find and use them.The graphs in Figure 1 were derived from a paper by Rob Macdonald of Rothschild Australia presented to The AusIMM Centenary Conference in Adelaide earlier this year. They show that the value of the industry on the Australian Stock Exchange halved over the past decade, despite the re-investment of capital equivalent to its full market capitalisation. Why is this so? The average dividend yields for the ASX Mining Index was never above five per cent during that period and barely averaged 2.5 per cent. Why then is $Ai million capital re-investment per employee since 1960 not enough to generate a rate of return to investors better than lousy bank interest? Do the investing public no longer regard our industry's assets to be world class?

Jan 1, 1993

By J St George

Much of AucklandÆs transport infrastructure has been developed on surface with little or no consideration of underground options. Current and planned transportation routes are now facing high costs due to land values and increasing environmental resistance to surface development. The option of utilising underground space becomes a feasible investment decision for these links as well as being the only option to develop the rail network within the inner city area. Transportation tunnels offer a quieter, more energy efficient means of getting around with minimal impacts on the surface environment. One of the major impediments to tunnelling is the high construction cost, which is partly related to the risks of encountering unexpected ground conditions and/or the possibility of causing surface ground deformations which could damage structures. The geology of Auckland has had substantial investigation through various studies and projects. The sediments of the East Coast Bays Formation (ECBF) underlie most of the Auckland urban area. It is classified as a soft rock and is a suitable material to tunnel through using either a tunnel boring machine or a roadheader. This paper reviews the limited amount of tunnelling completed in the urban Auckland area, together with the international advancements that have been made in the tunnelling industry. From the known features of the local geology and the problems encountered historically, the likely risks of tunnelling in Auckland are presented and ways in which those risks could be reduced and managed, are discussed. In addition, contractual arrangements between client and contractor are assessed with respect to complicated projects (such as tunnelling), so that the risks can be managed to create efficient infrastructure routes with reduced costs.

Jan 1, 2008

By Kam KM, Tran B

Statistical techniques of Box and Jenkins (1976) have been used to assess the existing control schemes and determine the dynamics of flash smelting furnace at the Kalgoorlie Nickel Smelter. Pertinent process variables, such as, oxygen flow, flux flow, matte grade and iron to silica ratio in slag, were considered in the analysis using routine operating data collected over two periods of operation. Results indicate inadequate control of some of the important variables. Dynamic characteristic parameters (dead time and response time) between a set of input and output variables were identified to improve optimisation of the existing thermodynamic model used for flash furnace control.

Jan 1, 1996