Search Documents

By R J. Butcher

Many deposits have been evaluated as potential block caves over the last 20 years due to the perceived benefit of low operating costs. However, block cave projects are typically capital intensive, with mass mining providing high throughput rates that required large investments in mining, processing and utilities infrastructure. While the key economic metrics in deciding to proceed with a caving project are typically net present value (NPV) or internal rate of return, these may not represent the best decision metrics for some companies. Where a caving project is competing for scarce capital amongst other projects in a company’s portfolio or where the caving project is the only project being evaluated by a company trying to raise capital, other metrics may be more appropriate. This paper explores the use of present value ratio and the minimising of maximum negative cash flow as suitable metrics in determining alternative strategies. Trade-offs between optimising for economic value and capital efficiency measures allow for decision-makers to evaluate potentially higher-risk, higher-capital and maximum NPV projects against lower-risk, lower-capital projects.CITATION:Stewart, C A and Butcher, R J, 2016. Block cave evaluation, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 809–816 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By E Nunes, R Mendes, D Jacobson, G Cota, T Machado, E Santos, J Almeida, E Pereira9, B Raso

Grinding circuits are known to be the highest consumer of energy used in the ore comminution process, with high operational costs and sensitivity to ore conditions. The mining industry is being encouraged to look for more energy efficient processes while increasing the mass and metallurgical recovery; a specific example is projects with lower iron ore grades, which demands a higher level of liberation and resulting higher energy consumption. This has led to increased usage of high-pressure grinding roll (HPGR) technology as an alternative design within the comminution circuit. A growing use of the HRC™ HPGR technology has been used to generate concentrate through a more sustainable process. In the Brazilian state of Minas Gerais, the readaptation of iron ore beneficiation circuits has been initiated, replacing the traditional crushing-to-grinding flow sheet with circuits using crushing-to-HPGR flow sheets, with the main driver being reduced energy consumption. Utilising results from sampling campaigns and analysis of experimental data collected in an industrial plant, the work herein presents a case study from the JMN Mineração operating plant, where the HRC™ HPGR was used as an alternative to traditional grinding using horizontal mills. The results show that the HRC™ HPGR performance in this iron ore processing plant showed benefits in terms of reduced energy consumption as compared to the projected performance with a traditional grinding circuit.

Sep 18, 2023

By B Hooper

Deep cuts in CO2 emissions will be required to stabilise and, in the long term, decrease CO2 concentrations in the atmosphere. Technologies for capturing CO2 from major stationary sources (power stations, industrial plants, etc) and storing that CO2 for long periods of time is one of few near term options for decreasing CO2 emissions. This transition to low carbon intensity energy and possibly the hydrogen economy through renewables and in the long-term technological developments such as artificial photosynthesis.Capture of CO2 from post combustion emissions can be done using a range of technologies though costs are currently high and dependent on the concentration of CO2 in the emissions. Techniques include solvents, pressure swing adsorption and the use of membranes. Options for decreasing capture costs by increasing the concentration of CO2 in the emission stream include the use of oxyfuels (in pulverized fuel types boilers) and by moving to integrated gasification combined cycle (IGCC) operations either simply for power generation or for poly-generation opportunities. Once the CO2 has been captured it can be stored using a variety of methods. Storage in the ocean has been suggested but is considered an unlikely option because of environmental uncertainties and political opposition. Mineral storage is a niche opportunity. The greatest potential lies in geological storage of CO2 and this option is commanding increased attention from the Australian and international community.In Australia, the Cooperative Research Centre for Greenhouse Gas Technologies (CO2CRC) is an important new initiative that will support energy companies and energy intensive industries in meeting challenges posed by greenhouse gas issues and assist them in their efforts to reduce their emissions profile.The progress of geo-sequestration and the challenges in the capture and separation of CO2 in the process industries are discussed.

Jan 1, 2004

By D van der Spuy, T Kewe, K Keet, N Moffatt, A P. Paine

The Blue Cube Mineral Quantifier Inline (MQi) instrument uses reflective light spectroscopy and advanced chemometrics to measure mineral or elemental grade in a slurry line. The instrument takes scans continuously and sends data to the DCS or PLC control system.Controlling the concentrate grades on a flotation circuit using low-frequency measurements can be difficult or impossible, especially on a circuit that has fast process dynamics. The ability to rapidly measure changes in grade makes it possible to continuously manipulate the flotation circuit operating parameters such as level, airflow and reagent addition set points to optimise plant performance throughout changing conditions.At Barrick’s Porgera mine in Papua New Guinea the flotation circuit feeds sulfide concentrate slurry to a pressure oxidation circuit. In order to maximise gold recovery in the flotation plant and increase performance in the pressure oxidation process, there is a stringent requirement to maintain a stable and optimum sulfur grade. The gold recovery is directly affected by the sulfur grade as most of the gold at Porgera is submicroscopic and associated with the sulfides (disseminated?pyrite).Porgera considered various points in the flotation circuit for installing Blue Cube analysers. This was part of a plant upgrade to improve process control. Due to budget constraints it was decided to initially only install one Blue Cube analyser on the final concentrate stream of the flotation circuit measuring sulfur, sulfides, gold and particle size. The accuracy of the calibration results were very good for all these properties. The sulfur measurement was used in an advanced control system to optimise and stabilise the grade. The paper presents comparisons between mineral grades determined using analytical laboratory analyses and the online Blue Cube data measurements, as well as benefits achieved by measuring grade online. An analysis of the plant data before and after installation of the Blue Cube and the advanced process control upgrade indicate that the flotation recovery increased by 1.98 per cent.CITATION:Kewe, T, Moffatt, N, Strobos, P, van der Spuy, D, Paine, A P and Keet, K, 2014. Evaluation of the Blue Cube MQi slurry analyser for application in an advanced control system for the optimisation of a gold sulfide flotation circuit, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 357–362 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

Many mining companies aim to integrate sustainability principles into their new projects. There is an intention for improvement, but frequently this results in little more than 'business as usual' projects that retrospectively categorise controls for environmental and social risks as sustainability initiatives as part of a public relations exercise. The successful implementation of sustainability requires a change of mind-set and behaviours at an organisational and personal level. In addition, sustainability incorporates a very wide range of interests and technical disciplines. One of the key challenges is in understanding how and when to pull these diverse threads together within a project or organisational process. This paper will explore a number of themes: What does it mean to implement a project in accordance with sustainability principles? How far beyond 'business as usual' is it reasonable to go, and what is the business case for this? Why do the intentions for sustainability sometimes fail and how can we prevent this happening in future? People are instrumental in delivering sustainability; how do we embed sustainability thinking into their behaviours and decision-making? The approaches that have been taken to integrating sustainability in design; what has and has not worked and some of the barriers to integrating sustainability into design? The authors will discuss these themes drawing on case studies from URS' experience in integrating sustainability into large projects. The authors will discuss the need for: a strategic approach which provides a simple framework for tactical decision-making and the consequences of taking tactical decisions in the absence of this framework, alignment of the project team and promotion of a culture of innovation, a shift from a risk/compliance mentality to an opportunity identification mindset, and a systematic approach to integrating sustainability into project design processes.

Jun 1, 2010

By C Switzer, R Logan, S Konopa, P Stoker, R Lewis

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Misima gold mine, located on Misima Island within the Milne Bay Province of Papua New Guinea, was operated by Misima Mines Pty Ltd, a subsidiary of Placer Dome Asia Pacific Limited (Placer), between 1988 and 2004. During this period, the mine produced 3.7 Moz of gold and 22.2 Moz of silver. In June 2012, the Special Mining Lease for the property was surrendered and incorporated into an Exploration Licence (EL). WCB Resources Ltd (WCB) entered into an exploration farm-in agreement with Pan Pacific Copper covering this EL.In June 2013, WCB published a new mineral resource of the Umuna deposit at Misima. All the drill hole data used for estimation was historical data collected by the previous owners of the Misima mine between 1977 and 2001. No new drilling was carried out by WCB. Confidence that the data could be relied on was provided by detailed interrogation of the existing data, reconciliation of the new resource model against production data and significant input from individuals who had previously been involved with the data collection, resource estimation and production activities of the Misima mine during its operation.This extended abstract will consider the challenges associated with locating, retrieving and validating historical data to use as inputs to produce an updated Mineral Resource estimate and comment on the material value of appropriate data storage, documentation and record keeping through the life of a project. It will also comment on the value of WCB obtaining access to the intellectual knowledge of many professionals that were former employees of Placer. This knowledge ensured that all the historical data that should have been available was sought out and accessed.CITATION:Konopa, S, Lewis, R, Logan, R, Switzer, C and Stoker, P, 2015. Misima gold mine – a case study in the use of historical data for an updated mineral resource estimate, in Proceedings PACRIM 2015 Congress, pp 579–586 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By C Rizos

Many of the ‘new paradigms in mining’ and notions of ‘sustainable mining’ have at their core the requirement for reliable, continuous centimetre-level positioning accuracy to enable increased automation of mining operations. The deployment of precision systems for navigating, controlling and monitoring machinery such as drills, dozers, draglines and shovels with real time position information increase their operational efficiency, and reduce the need for humans to be exposed to hazardous conditions. The Global Positioning System (GPS) is the best known, and only currently fully operational, Global Navigation Satellite System (GNSS) providing positioning capability anywhere in the globe, on a continuous 24/7 basis, with accuracies ranging from the dekametre-level to the sub-centimetre-level depending on hardware and operational configuration. Despite this versatility, GNSS cannot satisfy the high accuracy positioning requirements for many applications in mine surveying, and mine machine guidance and control. The reason is that increasingly open cut mines are getting deeper, resulting in a reduction of the ‘sky-view’ necessary for GNSS systems to operate satisfactorily. Yet, to date there have been no viable alternatives to GNSS that can be deployed in mine environments that can meet the challenging requirements in open cut mines.Locata Corporation, a Canberra-based company, has invented a terrestrial high accuracy positioning system known as ‘Locata’ that can augment GNSS with extra terrestrial signals to permit cm-level positioning accuracy even when there are insufficient GNSS satellite signals for reliable positioning and navigation. Locata relies on a network of synchronised ground-based transceivers that transmit positioning signals that can be tracked by suitably equipped user receivers. Hence Locata can be considered a new type of ‘local constellation’, able to provide high accuracy positioning coverage where GNSS fails. This paper introduces some of the technical aspects of this Australian technology and describes tests conducted by Leica Geosystems over the last few years at Newmont Boddington Gold in Western Australia. A recent news announcement by Leica Geosystems (12 January 2011) has confirmed that their new mine management system will have combined GNSS + Locata positioning capability – the first commercial product that integrates GNSS and Locata capabilities into a single high accuracy and high availability navigation device for open cut mine machine automation applications.

Nov 22, 2011

By N Setoudeh, A Nosrati, N J. Welham

The current surge of interest in lithium (Li) is due to the anticipated demand for electric vehicles and small scale power storage. Brine deposits contain most of the global Li resource, however hard rock deposits can be more readily and rapidly developed and comprise the majority of proposed projects. These projects plan to use the conventional processing routes of dense medium separation and / or flotation to produce a spodumene concentrate for sale. The standard route for subsequent processing of spodumene concentrate is thermal decrepitation, acid leaching, solution purification and precipitation of lithium carbonate. This is typically followed by further purification. A number of projects have ores which contain other lithium minerals, principally micas, lepidolite and zinnwaldite, necessitating an alternative treatment route. Several different routes for spodumene processing are under development to reduce costs to compete with brine projects. This paper will give an overview of the strengths and weaknesses of the current and alternative processes.CITATION:Welham, N J, Nosrati, A and Setoudeh, N, 2017. Lithium ore processing – an overview of the current and new processes, in Proceedings MetPlant 2017, pp 185–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By C D. McCullough, M Gerner

Rarely do opportunities arise allowing closure of a mine site to be planned as a key beneficial land use asset within a new urban growth area; particularly so well prior to cessation of mining.Pit lakes are common mine closure legacies for many open cut mines and may form in open cut mine voids extending below the water table upon closure. Mine closure guidelines increasingly require post-mining land uses of equivalent capacity to premining conditions and that minimise long-term post-mining liabilities and maximise benefits to stakeholders and the environment. However, risks presented by pit lakes are regularly neglected in closure planning or are not able to be addressed to allow beneficial end use of the lake or surrounding land.This paper describes strategic planning initiated by quarry owners ten years before mining ceases. In liaison with the planning agencies, the planned closure of a large 100-year-old limestone quarry pit will form a lake on mine completion, with a well-considered beneficial end use in an urban setting in mind. The quarry pit and adjoining land at Batesford South about the edge of the City of Greater Geelong, Victoria, Australia. Geelong is experiencing growth pressures that necessitate development of a new growth area from about 2025.A multidisciplinary expert team assessed the constraints, opportunities and feasibility of rehabilitating the quarry and pit lake and developing the surrounding land as Geelong’s next urban growth area.The concept is exciting and demonstrates that a former mine site could become a valued home to about 40 000–45 000 people. About 30 per cent of the land will also be developed as an ecological riverine corridor including the pit lake that will become a regionally iconic lake as the centrepiece of an urban development.Our paper outlines technical challenges and how these can be met to achieve closure and beneficial use that meets the social, economic and environmental expectations of contemporary urban planning.CITATION:Gerner, M and McCullough, C?D, 2014. Planning for the future – development of beneficial end use from a quarry pit lake, Victoria, Australia, in Proceedings Life-of-Mine 2014 , pp 99–112 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By I Canbulat, J Oh, A Mcquillan, D Payne

This paper presents a new risk assessment tool for coal mine excavated slopes. This new empirical-statistical Slope Stability Assessment Methodology (SSAM) is intended for use by geotechnical engineers at both the design review and operational stages of a mine’s life to categorise the risk of an excavated coal mine slope. A likelihood of failure is determined using a new slope stability classification system for excavated coal mine slopes developed using a database of 119 intact and failed case studies sourced from open cut coal mines in Australia. Consequence of failure is based on slope height and stand-off distance at the toe of the excavated slope. Results are presented in a new risk matrix, with slope risk being divided into low, medium and high categories. The SSAM is put forward as a new risk assessment tool to assess the potential for, and consequence of, excavated coal mine slope failure. Unlike existing classification systems, assumptions about the likely failure mode or mechanism are not required. Instead, the SSAM applies an approach which compares the conditions present within the excavated slope face, with the known past performance of slopes with similar geotechnical and geometrical conditions, to estimate the slope’s propensity for failure. The SSAM is novel in that it considers the depositional history of strata in an excavated slope and how this sequence affects slope stability. It is further novel in that it does not require explicit measurements of intact rock, rock mass and/or defect strength to rapidly calculate a slope’s likelihood of failure and overall risk. Ratings can be determined entirely from visual observations of the excavated slope face. The new SSAM is designed to be used in conjunction with existing slope stability assessment tools. CITATION:Mcquillan, A, Canbulat, I, Payne, D and Oh, J, 2018. New risk assessment method for coal mine excavated slopes, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 473–495 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By C M. W Boyle, E K. C Phuak, A Lewan, E Ryan, M D. Paine, P H. Mackenzie

"Rio Tinto Iron Ore (RTIO) has an extensive history in the application of geometallurgy to the iron ore value chain. Fundamental to this has been the geological logging of material types which are assigned processing attributes such as lump per cent and density. Initially these were used for product (lump and fines) grade predictions in relation to grade blocks to be used within short-term planning horizons.More recently the predictive reach of the material types and their associated processing attributes has been extended due to their inclusion into geological block models. These predictions can now be used to influence mine plans across multiple planning horizons in such a way that the extremes of geometallurgical properties can be pre-empted and managed thus improving efficiency. Spatial material type domains are also used in the planning of metallurgical drill holes to ensure greater representivity of material than was typically obtained by chemical and/or stratigraphic criteria alone.Material type logging has also been enhanced by the introduction of modern, rapid mineralogical techniques that have complemented visual logging. This has enabled the identification and quantification of contaminant minerals and their relationships with host ore types to be established. This data is used to better manage product grade predictions and identify risks to the short-term plan.Work is ongoing in RTIO to further refine logging based predictions and in addition apply them to new areas of the business. This work requires collaborative and multidisciplinary teams working on an integrated approach combining geology, metallurgy, technology and innovation, mine planning and technical marketing.CITATION:Paine, M D, Boyle, C M W, Lewan, A, Phuak, E K C, Mackenzie, P H and Ryan, E, 2016. Geometallurgy at Rio Tinto Iron Ore – a New Angle on an Old Concept, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 55–62 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By D J. Robinson, L L. Kuhar

In-situ recovery (ISR) is accepted and applied across many geographies, and approximately 50% of the world’s uranium is currently extracted by using an ISR method (World Nuclear Association, 2014). The low environmental impact, the elimination of risk for mine workers and the fact that all of the lowest-cost producers of uranium use an ISR approach should raise interest from traditional miners (IAEA, 2014). However, the broader application of ISR to other commodities and mineral systems remains limited. A number of demonstration (experimental) copper projects have been undertaken (Sinclair and Thompson, 2015) with a few copper projects in Arizona being close to demonstration (Florence, 2018 and Gunnison, 2018). Evidence of very few economically operating ISR copper projects can be found (for example, the Russian, Uralgidromed OAO, built by the Russian Copper Company in 2005 and operated as an ISR facility from the Gumeshevskoye deposit (Russia Mining, 2018). A number of gold deposits, particularly paleochannel deposits, have also been considered for ISR, but, to the best of our knowledge, only limited demonstration and no commercial operations have been established, yet (Kuhar et al, 2018 and references therein).CITATION:Robinson, D J and Kuhar, L L, 2018. Extending mine life through application of an in situ recovery approach, in Proceedings Life-of-Mine 2018, pp 56–57 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By D Reid

Run-out analyses of tailings storage facilities are typically undertaken using methods based on rheological theory. These are reasonable techniques to model the behaviour of tailings that, through significant run-out and possibly mixing with supernatant water, are generally acting in a fluidised manner. Such modelling often follows on from two-dimensional continuum analysis models where, if failure is predicted, grid failure often occurs when deformations begin to increase. This results in a disconnect between the prediction of failure and the modelling of the potential extent of the failure.Recently, rezoning methods have been incorporated into commercially available two-dimensional soil mechanics deformation codes. Rezoning techniques enable large deformations to be modelled within a two-dimensional continuum analysis framework; however, while promising, the use of such tools is not yet widespread, and a consensus is yet to develop on how they should be applied to tailings dam run-out modelling.This paper uses FLAC rezoning techniques to model the flow behaviour of two historic tailings dam failures. The purpose of these analyses is to critically assess the performance of rezoning against some available historic failures. The required data to undertake such an analysis is outlined, along with the inherent limitations and assumptions required. Parametric analyses are outlined to address some of these issues. In general, the analyses undertaken underestimated the flow distance observed in the historic failures by varying degrees; however, in some instances, the analysis reasonably reproduced the qualitative shape of the initial failure zone. A variety of potential reasons for the discrepancy between historical observations and the models undertaken are provided.CITATION:Reid, D, 2015. The use of rezoning techniques to model historic tailings failures, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 201–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By C J. Unger, A M. Lechner, A Walton, V Glenn, M Edraki, D R. Mulligan

In Australia, responsibility for abandoned mines can be unclear. With a few exceptions, state and territory governments have become responsible for abandoned mines on Crown land and private landholders are responsible for abandoned mines on freehold land. Abandoned mines pose risks and opportunities across the full suite of sustainability themes (environmental, human health and safety, socio-economic and community development) after mining ceases.Across Australia, there are more than 50 000 abandoned mines recorded, ranging in size from individual shafts to large polluting open cut mines. Addressing the safety and environmental impacts of these sites, as well as the socio-economic development opportunities of significant rehabilitation projects, requires the implementation of effective policies and programs. Qualitatively defined graded scales or ‘rubrics’ have been used for many years in student assessment and increasingly in the performance assessment of other sectors (Davidson, 2005). While risk-based maturity models have been used for safety prioritisation (Westrum, 1993; Hudson, 2007; DRET, 2008; Hancock, 2010) and evaluation of organisational development (Esteves et al, 2010), this paper is the first to adapt maturity models for the evaluation of abandoned mine rehabilitation programs in Australia.In this paper, we used indicators based on the national policy for abandoned mines to assess the maturity of abandoned mine programs. Fourteen elements of maturity were identified (Unger et al, 2012) under the five chapters of the national policy for abandoned mines (MCMPR and MCA, 2010). Jurisdictions were then evaluated and ranked on their maturity on the basis of information that was web-accessible. Information transparency of abandoned mines policies and programs is in itself one element of the maturity chart. Each jurisdiction in Australia was compared with one another and with a Canadian jurisdiction; the British Columbia (BC) Crown Contaminated Sites Program (CCSP), which represents leading practice (Unger, 2009; Unger et al, 2012).Our research found that in some jurisdictions in Australia there is little or no information on abandoned mine programs or individual abandoned mine sites on government websites, while other jurisdictions provided very detailed program information on planning, funding and implementation. Each jurisdiction in Australia, for which web-based information was available, had some elements where they were more mature than other Australian jurisdictions. For some elements, maturity ranked equivalent to the BC CCSP, but most Australian jurisdictions were less mature. There was only one element where a single Australian jurisdiction ranked higher than the BC program in maturity. Legacy mine policies, programs, priorities and funding information via departmental websites are easier to find in some jurisdictions, indicating progression toward greater transparency and more mature programs. A systematic approach to monitoring and evaluating abandoned mines programs is essential for accountability as it can demonstrate liability reduction over time and continual improvement. The maturity model approach can provide both a measure of progress over time as well as a tool to support the implementation of the national policy for abandoned mines (MCMPR and MCA, 2010).CITATION:Unger, C J, Lechner, A M, Walton, A, Glenn, V, Edraki, M and Mulligan, D R, 2014. Maturity of jurisdictional abandoned mine programs in Australia based on web-accessible information, in Proceedings Life-of-Mine 2014 , pp 467–480 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By R Bradford, W Gift-Agbey, T Vorster, P Morgan, E Grobler

The Asanko Gold Mine in Ghana started processing ore from the Nkran pit in January 2016 at a production nameplate of 3 Mt/a. The flowsheet is a conventional SAG, ball mill and pebble crusher (SABC) with gravity-gold and carbon-in-leach (CIL) recovery. The nameplate production was comfortably achieved within 3 months, so much so, that it was clear the SABC circuit was capable of processing more than the downstream section of the plant. Consequently, a program of de-bottlenecking was initiated to rectify volumetric capacity constraints. This program was later referred to as ‘Project 5 Million’ (t/a) or P5M. Having completed the de-bottlenecking exercise, it became evident that the SABC circuit could not reach 5 Mt/a solely on hard rock from Nkran. The new challenge was therefore to increase the capacity of the milling circuit through a focused comminution initiative that would address the following: geometallurgical treatment plan; upfront fragmentation requirements; installation of feed and mill monitoring equipment; and integration of a knowledge-based control strategy. This paper takes the reader through the various measures implemented to increase the milling rates and to create a stable/ sustainable control philosophy. As a result of the implementation of advanced mill performance monitoring technology (MillSlicer) and the collaboration between a team of experts in comminution, control and operations, the Asanko Gold Mine process plant feed tonnage has successfully increased from 3 Mt/a to 5 Mt/a.CITATION:Bradford, R, Gift-Agbey, W, Grobler, E, Morgan, P and Vorster, T, 2018. Optimisation of Asanko’s Obotan SABC circuit to achieve ‘Project 5 Million’, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 477–484 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Hegedus M

The Hydrogeological Survay of the bauxite mines in Hungary was establisned 30 years ago. The goal of the HS has been to collect the all available date needed to solve the hydrogeological problems of bauxite mines. The results of activity of the HS have been summarized in the annual reports-. This report is going to present a few methods to evaluate the hydrogeological properties of fissured, karstic rock ie. the evaluation of drilling mud losses, the statistics of core samples evaluated by a special computer program for calculation the porosity and permeability of the rocks. An experimental injection test is presented together with the development of a new portable instrument to get signes of the water table change during the injection test in every two second. It can be proved that the flow around the well may be a transient one if the yield of the injection exceeds a definite one (Figure 2.). It was observed that the permeability calculated from the pumping test date may be 1.2-1.6 time higher than it coming from the injection test. A practical example is presented also how to use the results of the HS for designing the dewatering of a new mine together with an analogous computer model to forecast the yield expectable for making the drift tunnel. A suggestion based on the hydrogeological feature has been done for the dewatering without using electric energy (see Figure 3.-6.).

Jan 1, 1988

By Sullivan T. D

The Lochiel Deposit is a large occurrence of soft brown coal about 130 km north of Adelaide. The deposit is undergoing continued evalua- tion of which an integral part was the excavation of a Trial Pit. The Trial Pit was deemed necessary to demonstrate that the deposit may be mined efficiently by draglines and the particular emphasis was on the geotech- nical and hydrogeological aspects of what may be termed difficult mining conditions. The dewatering of the Trial Pit was commenced in September 1986. After considerable planning and excavation was successfully completed in May 1987. The project is unique in terms of its size and technical com- plexity. It entailed excavation of over 230,000 m3 of overburden to an overall depth of 36 metres. The excavated material was utilised for experimentation in a Trial Dump. Included in the Trial Pit design were several novel techniques includ- ing depressurisation drains to improve mining conditions in soil strength materials and the use of vacuum to aid dewatering.

Jan 1, 1988

Underground mine ventilation is now com monly simulated on a digital computer. Such a programme, incorporating natural ventilation has been modified by others to account for methane emission and elevated local tempera- tures. At Wollongong University, the pro- gramme was further developed and extensive interactive graphics incorporated such that any view of the three dimensional mine could be viewed, and superimposed upon that view are areas where a nominated parameter has exceeded a particular value - generally at a nominated time after a particular event and usually a fire/explosion of one type or another. A further programme was developed such that up to 20 'times' could be examined at a particu- lar location after say, a fuel rich fire at some other place in the mine. The output from this programme includes a plot of methane 1, smoke 1, temperature, pressure and air flow versus time - a most useful graphic to observe the limits of safe attendance in a particular Airway.

Jan 1, 1983

By J Webb

The mining industry is relatively niche and complex compared to other global industries in its safety and operating environment. Whilst some of the technology required to decarbonise the mining industry will emerge from the mass market (eg batteries, energy storage solutions and renewable power generation) where exogeneous external investment and innovation will drive supply, bespoke applications such as material movement will be constrained by industry limitations. Underground load and haul equipment burns the majority portion of underground mine diesel, and typically 25 per cent of scope one and two emissions. Transitioning away from incumbent diesel engines offers a considerable health benefit to all mine workers, as well as decarbonisation achievements, and through trials there is emerging evidence of more productive equipment and realistic expectations of lower operating costs of fleet. However, new equipment and material movement systems that support these industry goals are currently approached with caution due to the pivotal role they play in delivering productivity goals, and the lack of experiential data and certainty to mitigate the supplier development risk during this technology transition period, where all resources are required to meet a booming industry. A group of mining companies and suppliers have the aligned aim to accelerate the understanding and availability of heavy haulage mobile equipment through collaboratively piloting equipment and working with suppliers and each other to aggregate market demand, encourage investment and resolve the mine design and technology choices through their involvement in the Electric Mine Consortium (EMC). This paper will outline the major challenges the industry must overcome in sourcing and adopting a zero-diesel particulate and zero-emission mine, drawn from cases and insights across ten EMC mining company members.

Mar 29, 2023

By T Tan, C P. Holmes, C E. Hartford

Transportation of iron ore from the mine to the plant is critical to business success. Ore from the mine may have to be transported across states, countries and even continents to get to the processing plant or export facilities, and ultimately to the client. Numerous transportation steps may result in potential logistical difficulties. Companies are continually seeking ways to increase production rates, decrease delivery times and reduce operating costs. Transportation cost is a major component of the total cost of mining iron ore and therefore requires effective use of transport systems.Bottlenecks in iron ore transport systems, due to material handling issues, can result in loss in profit in the order of millions of dollars per hour. Bottlenecks can be seen anywhere in the transport system where the desired flow rate cannot be achieved. These bottlenecks occur for various reasons such as increasing throughput in a transport system originally designed for a lower throughput resulting in plugged transfer chutes, changing material characteristics (eg finer material, increased moisture content), changing to a new type of material or blend that again alters handleability, or changes in operational philosophy due to equipment availability or process utilisation.Stockpiles may have limited live capacity such that an adequate amount of ore may not be readily reclaimed when required (eg to fill a complete train’s railcars). In bins and hoppers, material may discharge through a central flow channel resulting in the formation of a stable rathole, which can then collapse causing material to flood the downstream system and cause significant downtime for clean-up (eg railcars beneath train load outs). In transfer chutes, bottlenecks can be caused by pluggages or downtime required for the change-out of liners due to excessive wear. In ship loading, long settling or de-aeration time, or material exceeding its transportable moisture limit (TML) may result in further bottlenecks. These bottlenecks all have associated costs because of the need to address their causes and because of the lost opportunities for throughput.This paper will discuss how bulk material technology and proper understanding of material flow characteristics can be applied to mitigate bottlenecks. It will discuss how to predict potential bottleneck locations through a scientific method of analysis and evaluation to determine if an increase in throughput of an existing transport system is possible, as well as whether or not a new material will flow reliably through an existing system.CITATION:Hartford, C E, Holmes, C P and Tan, T, 2015. De-bottlenecking iron ore transportation from mine to plant, in Proceedings Iron Ore 2015, pp 393–398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015