Search Documents

By Redman P. G, McMahon B. K

A simple technique for evaluating the field stress ratio is presented, based on the results of extensometer or convergence tape measure- ments taken in an advancing tunnel. This tech- nique also yields a value for the rock mass modulus, provided Poisson's Ratio is assumed. The results of two case studies are presented illustrating the effectiveness of the method.

Jan 1, 1981

By Smith Z, Huppert P, Charbucinski J

The paper describes a spectrometric method and apparatus developed for lithology logging in brown coal formations. The nuclear spectromet- ric technique developed is able to delineate coal/sand/clay seams. One requirement was to log inside drilling rods, as well as cased or open holes. The method described is based on combined natural gamma and gamma- gamma techniques using a spectrometric system for signal acquisition and subsequent computer based on-line data analysis and interpretation.

Jan 1, 1989

By Denby B

The ever increasing demand on land use has led to large areas of land being considered for development, which because of past mining activities are covered by substantial depths of fill materials. This paper examines the problem faced with the development of land infilled with open cast mining backfill, in predicting the behaviour of the fill upon development. To be able to design foundations suitable to withstand the movements that occur within open cast backfills or design a backfilling operation that produces land suitable for a proposed after development, a means of predicting backfill settlement is required. Factors critical to this prediction are the timing of backfilling operations, the compactive state of the backfill and the inundation of the backfill. The analysis of a considerable quantity of data collected from the monitoring of backfilling operations and backfill movement at a range of open cast coal sites located within the UK has given the authors a better understanding of how open cast backfills behave in terms of long-term creep settlement, collapse settlement and how these are effected by backfill scheduling. This knowledge has been encoded into a program running under Microsoft Windows that enables a user to make settlement predictions for a point, a given section or area or for the whole site. Differential settlements, critical to any development design, can also be determined between any two points taking into consideration the heterogeneous nature of open cast backfills. The program was tested with data from an open cast coal site in the UK. Compaction monitoring during the placement of the backfill material enabled a model of the backfill to be constructed taking into account backfill properties and scheduling. This model, taken as input into the program, enabled future backfill settlement predictions to be made. A comparison is given between these results and actual settlements obtained from a short-term settlement monitoring scheme.

Jan 1, 1995

Laboratory high tension roll separation and the commercial machines available for this purpose are discussed. The shortcomings of these machines are indicated and a machine that overcomes some of these undesirable character- istics is described. A procedure for evaluating laboratory high tension roll separation is described. The use of this evaluation procedure in conjunction with the laboratory separation is described with examples taken from the Dunwich and Hexham processing plants of Associated Minerals Consolidated Limited. Evidence that laboratory testwork results may be directly transposed to operating plants is given. A discussion of the effects of variables in high tension roll separation of mineral sand concentrates concludes the paper, and uses in support results obtained in the metallurgical laboratories of Associated Minerals Consolidated Limited, Southport, Queensland.

Jan 1, 1972

Coal is a very versatile resource, having variable characteristics and having potential for a wide variety of mar- kets. Australia has extensive deposits of black coal, although they are concentrated mainly in Eastern Australia. Assessments of the currently known reserves are related to the qualities of these reserves. Markets available to black coal fall into the broad groupings of metallurgical, fuel, conversion and miscellaneous markets and the requirements of these markets are related to coal characteristics. Market trends in Australia and on the export market are discussed and projected forward. By the end of this century Australian consumption of black coal could well be 100 million tonnes per annum, and, in the absence of any export restriction, a similar amount is likely to be exported. Currently defined black coal resources in Australia will last at least 600 years at these projected rates of consumption. Although the position appears satisfactory in considering the projected life of the black coal resources, there is a serious lack of detailed information on reserves, mining and preparation yields, quality and possible environmental restrictions. Action is required on three parallel courses: (1) a consistent, systematic and extensive survey of current coal resources in Australia, (2) accelerated exploration activity to define poorly prospected and potential areas, and (3) regular updating and extension of the knowledge of Australia's coal resources. This information would be of tremendous assistance for the formulation of a national energy policy on coal.

Jan 1, 1975

Lightweight polymer grids have recently been introduced to the mining industry. They are currently being used for roof and rib control, longwall shield recovery, safety guarding or barricade, highwall screening, internal reinforcement of gunnite/shotcrete applications, sub-base reinforcement, construction of steepened slopes, retaining walls, mine reclamation (i.e. erosion control, turf reinforcement), and in numerous mining waste related projects. These polymer mining grids utilize a strong, lightweight polymer, usually special grades of polypropylene or polyethylene. High tensile strengths are achieved by molecular orientation of these polymers in the manufacturing process. The first step in the manufacturing process is to extrude the polymers into thick continuous sheets. These sheets are then punched, and drawn into open grid structures. Aperture size and configuration are controlled by the geometry of the punched hole and the degree to which the grids are stretched. The drawing process is the key to the molecular orientation required for the tensile strengths. These long chain polymer molecules in their natural state have a random orientation. When stretched, the molecules are pulled into a parallel alignment, thus creating a lightweight product with tensile strength comparable to Steel.

Jan 1, 1992

By Heidecks C

Sub-level stoping with consolidated rockfill is the main method for mining steep dipping baryte and fluorite veins in Germany. Drifting is fully mechanised using drill jumbos, LHD units and shotcrete support. Stopes have heights up to 50 m with sub-level distances up to 15 m. Winning of the pillars between sub-levels is done by longhole blasting in slices of 3-5 m length on strike. Mucking is done on the lowermost level by LHD units. After each blast rockfill with binder (cement and/or fly ash) is dumped into the scope from the uppermost level. Economic success depends on both geological and technical parameters and factors, eg vein thickness and dip, ore grade, size and distance of sub-level drifts. Of particular influence are ore loss in pillar winning and dilution both in drifting on vein and in pillar mining. A comprehensive computer program has been developed for calculating the total cost per tonne run-of-mine ore respectively per tonne of concentrate for a single stope. The cost model includes development, longhole blasting, mucking and haulage to the mill, milling and ventilation. All costs (labour, energy, supplies, maintenance, depreciation and capital cost) are taken into account. Dilution and recovery are both considered. The program can be used to estimate the cost of mining a particular stope. It can also be used to investigate the influence of relevant parameters and factors on the economic result. By this way it should be possible to optimise the technical design of a stope.

Jan 1, 1995

By Golab K, Partridge AC, Fletcher CAJ, Holtham P

Spiral concentrators are used globally in the fine coal processing industry to segregate particles, by gravitation, on the basis of density and size. Consisting of an open trough that twists vertically downwards about a central axis, a slurry mix of particles and water is fed to the top of the concentrator. Particles are then separated radially as they gravitate downward. Since their introduction to Australia in the 1940's, the generic design has evolved largely by laboratory trial-and-error investigations of different prototypes. However, this approach has proven expensive and optimal designs have not been necessarily developed. Accordingly, Computational Fluid Dynamics (CFD) analysis has been used recently as an alternative method of investigation, to assume as is envisaged, a role in the design process. To date, CFD models have progressed to simulations of turbulent fluid flow on current production spiral designs, and are continuing to be adapted for inclusion of particles at realistic feed concentrations. To be able to use the models confidently however, laboratory experiments must also be performed to validate the predictions during the development stage. This paper reports the current findings of an ongoing CFD and experimental program applied to one spiral unit. Satisfactory quantitative agreement has been achieved for the fluid and particulate flow characteristics, and although further validations are appropriate, the model already possesses significant potential for use as a reliable predictive design tool.

Jan 1, 1998

By Jorgensen FRA, Moyle FJ, Turner TM

Laminar flow furnace techniques and thermal analysis were used to study the combustion of Kambalda nickel concentrate and Collie coal. The study was made to ascertain the suitability of the latter as a replacement for the fuel oil currently burnt in a flash furnace at the Kal- goorlie Nickel Smelter. The coal was found to ignite at temperatures between 500-600¦C which was the same as that required for the most reac- tive component of the concentrate, namely py- rite. The rates of reaction of both the coal and concentrate were dependent on oxygen con- centration. Sulfur dioxide hindered the combus- tion of concentrate and of coal, the effect on the concentrate being the more pronounced. The effects of moisture content and the tendency for spontaneous combustion of the coal were also noted.

Jan 1, 1982

The Canada Centre for Mineral and Energy Technology (CANMET) /Calgary Coal Research Laboratory and the National Research Council in Ottawa established a joint working research group with industry to develop and test various computer models for application in surface coal mining operations in western Canada.The first part of the paper deals with the problems the group experienced during the past two years especially having model specification and requirements defined and understand site management practices.The second part of the paper deals with site specific development of general mine model for TransAlta Utilities' Highvale Mine in Alberta. Described here are the development of an interactive truck/shovel model for their three pit operation, selection and application of dragline model for tandem operation with the extended bench method, criteria for operational model of the five seams operation with selec-tive mining approach.

Jan 1, 1985

By S Robson, T G. Blenkinsop, S C. Dominy

Golden Pig mine is in the central part of the Southern Cross greenstone belt within the Archaean Yilgarn craton. The mine has produced approximately 2.5 Mt of ore at 5.7 g/t Au to yield approximately 450 000 oz. The majority of gold mineralisation is hosted within extensively deformed and quartz-veined BIFÆs. In addition to the BIF-hosted mineralisation, an increasingly important part of the resource lies in the Taurus Lode, which is a N-NNW-trending amphibolite facies shear zone. The Taurus Lode lies within a continuous shear-zone that has a moderate to steeply WSW dipping foliation, and a mineral lineation of biotite, amphibole and pyrrhotite plunging consistently 10¦ S. Drive faces, subperpendicular to the foliation and lineation, consistently show evidence for syn-mineralisation reverse shear. Exposures parallel to the mineral lineation and perpendicular to the foliation reveal both sinistral and dextral asymmetries. These characteristics suggest that the vorticity axis of the Taurus Shear Zone is parallel to the mineral lineation, and that the simple shear sense is reverse. This geometry can arise when there is a major component of flattening across the shear zone, which may be due to interference between two adjacent granite domes. The BIF-hosted lodes plunge consistently 15¦ NNW coincident with the intersection of the axial planar cleavage of the regional folds and the Taurus Shear Zone. However, where the penetrative shear characteristics control the orientation and geometry of the mineralisation, oreshoots plunge SSW, parallel to the stretching and mineral lineations within the shear. The SSW plunge of strike extensive and laterally confined high-grade, economic ore shoots within the Taurus shear is fundamental to defining the economic mineralisation within this lode. Identifying the zones of maximum continuity and establishing the optimal position for future development will maximise ore extraction.

Jan 1, 2003

DURING the four years, 1922, 1923, 1924, and 1925, China produced the following quantities of non-ferrous metals and ores: Antimony Products - 67,869 (long) tons. The production for 1925 was 20,869 tons, of which 80% was regulus, 14% crude,and 6% oxide.Arsenic (White) - 4200 tons. The production for 1925 was 1200 tons, but only 90 tons were exported, some 25% of which to Hong-Kong, France, and U.S.A. each, and the rest in small lots to other countries. Domestic consumption was 1110 tons, and thelocal price for "cake" was around £47 per ton on 1925 exchange.Arsenic Ore (Realgar) - 1400 tons.Lead Ore (Galena) - 44,853 tons. The production for 1925 was 10,853 tons, of which 16%, produced in Korea, went to Japan, and 84% produced in Hunan, went to Europe.Manganese Ore (Pyrolusite) - 142,567 tons. The production for 1925 was 42,567 tons, of which 94.3% went to Japan.Tin Ingot - 33,480 tons. In 1925 the exports to Hong-Kong were 8880 tons of usual rough tin of 94% to 96%. Most of this was refined to No. I Chinese quality of 99.3% and exported to U.S.A. and Europe, owing to the good price ruling.Sulphur - 12,000 tons. Sulphur is included in this list in order to explain how its production led to the discovery of some other ores.Wolfram - 19,668 tons. The production in 1925 was 5868 tons, most of which came from the Quee Mee mountain district in South Kiangsi, from the detrital deposits. Civil disturbances prevented the usual output from Hunan border.Zinc Ore (Blende) - 134,190 tons. Exports for 1925 were 34,190 tons of low-grade ore, averaging 30% zinc, 14% lead, and 7% silver...

Jan 1, 1927

Diamonds have been known in Australia for many years, especially in association with alluvial gold and tin occurrences. Exploration for primary sources in the Kimberely area of Western Australia has been carried out since 1968, culminating in the discovery, in 1979, of the Argyle Kimberlite No 1 (AK1) kimberlite pipe. Various techniques have been used in the search for diamonds such as geologic interpretation, aerial photography and Landsat, soil geochenical techniques, geophysics, and stream sediment sampling. Stream sediment sampling, a method developed in South Africa, using the detection of indicator minerals derived from kimberlites in gravel samples, has had wide application and success in Australia. Nevertheless, although Australian diamond bearing kimberlite and lamproite rocks contain some of the classic indicator minerals, their concentrations are generally much lower than in South Africa and Russia. Despite this paucity of indicators, stream sediment sampling is still the best known and most commonly used method of diamond prospecting in Australia. Small samples are treated by hand but larger samples require the use of diamond pans, jigs or heavy media separation plants. Each of these methods has advantages and disadvantages. The final concentrate is passed over a grease table or subjected to x-ray sorting.

Jan 1, 1984

By Lorenzen L

In South Africa, as in many other countries, the young engineering graduate is promoted quite soon to a management position where he uses less technical skills and more people-oriented skills. In the standard undergraduate curriculum for engineering, little attention is paid to the non-technical issues of the profession. An undergraduate course in management techniques cannot be a substitute for a MBA or Masters degree in engineering management, but can at least create an awareness of the practical problems facing the engineering manager. The aim of this paper is to provide an outline of such a course structure at the University of Stellenbosch. A survey is also presented on management training in the South African and Australian mineral industries. Feedback from students and graduates indicates that the fresh graduate does not fully appreciate the value of such a course until he/she achieves a position of responsibility after two or three years. Nevertheless, the management course appears to be successful in widening the perspectives of the engineer. As explained frequently in management journals, the technically oriented person (the engineer) has a convergent thought pattern, which could be in conflict with the more divergent thought pattern of the top, personnel or marketing manager. It becomes increasingly imperative for the young minerals engineer to be externally oriented instead of the traditional internal focus of engineering. The engineer should not only be aware of environmental issues in the technical design and operation of plants, but should also understand the inter-relationship between public relations, political pressures and environmental perceptions vis-d-vis technical facts.

Jan 1, 1993

By Chugh Y. P

A generalized void diffusion model for subsidence prediction has been developed based on theoretical concepts and physical principles. The general form of the model is a three-dimensional differential equation. With a few assumptions on the characteristics of overburden strata overlying typical room-and-pillar mining or longwall mining systems, specific solutions for the differential equation were obtained. A brief description of these solutions and their applications in the United States and China are presented in this paper.

Jan 1, 1992

Extensive reserves of kaolin of the type suitable for use as a high quality paper coating exist on the Weipa Peninsula. In 1986 a commercial processing plant was constructed to produce 100 000 tonnes per annum of coating quality kaolin targetted principally for export. A number of processing difficulties have limited the production capability of the plant. The prime area being the pressure filtration operation with achieved cycle times being around 50-60% of design. The rate determining steps being press filling, press unloading and filter cloth washing. This paper details and summarises testwork and results from our attempts at decreasing the filtration cycle time.

Jan 1, 1989

By Ghose AK

Design and selection of support systems for longwall faces call for in-depth know- ledge of strata mechanics and in particular of strata-support interactions. The paper presents the results of field investigations and analysis of a difficult-to-cave roof using powered supports under a massive dolerite sill in Central India using a state- of-the-art datalogger system. The mechanised long wall face was equipped with 4/680 tons chockshields operated on the IFS mode using a 300 KW DERD shearer. The datalogger system was capable of storing data simulta- neously in 32 channels. The paper describes the monitoring system and the monitoring programme. The system provided useful information on support behaviour, build- up of leg pressures and face convergence during an intense dynamic periodic weighting phenomenon which destroyed the integrity of almost half of the face supports. At this point, the face had advanced by about 197 metres from the barrier. The paper outlines a post-mortem analysis of this dynamic event and provides a critical evaluation of the data collected for understanding strata support interaction and the behaviour of the massive sill in the overburden.

Jan 1, 1992

The underground mining of a narrow vein hard rock orebody is a capital and labour intensive method of extraction. Due to the nature of underground mining it is difficult for higher level managers to physically see the efficiencies and inefficiencies of a particular method. Extraction methods and sequencing often need to be altered from the original planned methods as a result of mine developent, providing more in depth information as it progresses. As a result of these issues contract mining of these orebodies is common practice. There are several types of contract structures for the purpose of underground contract mining with many complex permutations of them that reflect the different needs of each individual company and orebody. The different contracts are arranged dependent on the mining companyÆs desire to transfer or, alternatively, embrace risk. This presentation gives a brief overview on these different methods and their various advantages and limitations with regard to small scale and narrow vein underground mining. With respect to these different contracting methods, the presenter reviews the mutual growth benefits of emerging partnering opportunities, specifically with regard to smaller explorers exploring and developing prospective mining tenements. The specific advantages to small explorers include the resource flexibility and speed of project development that private mining contractors can provide. Given the contracting methods that are available, there is potential for small private mining companies to gain minor stakes in major projects and major stakes in medium sized projects by employing innovative contracting solutions to provide mutual benefits to the parties. Some potential scenarios to this effect are suggested in the presentation. This paper is available as a PowerPoint presentation only.

Jan 1, 2006

By Miles M. J, Sandy D. A

It has long been known that drilling and blasting operations have a direct influence over productivity and costs of subsequent operations. If mine management is to effectively optimise blasting operations, good information is required on the operating costs of each of the affected operations, together with knowledge of how they are influenced by blasting. In practice it is not possible to do enough repeats of a full scale production blasting experiment to make a statistically significant analysis of the results. By monitoring each blast and subsequent operations in as much detail as possible, enough data will be available to effectively measure the effect of blasting on costs. This gives management an insight into the blast performance and is the first step towards optimisation. An Integrated Blast-related Cost Reporting System has been developed at the Rossing Mine Open Pit, which calculates the total mining cost for each blast. In assessing the total mining cost for each blast, use was made of an.integrated planning and management information system to collect relevant production variables, current operating costs and survey data. An automatic image analysis system was employed to measure the fragmentation of the blasted material in the back of haul trucks. A shovel monitoring system is also under development for use in assessing the muckpile diggability and, in conjunction with an appraisal of shovel component reliability, to estimate the maintenance cost under various digging conditions.

Jan 1, 1990

By Wu Y. H, Lu J. P

Slope stability has now become a practical tool in the design and oper- ation of open pits. The stability of rock slope depends on many factors, including not only structural geology, the existence of weak layers, ground- water, blasting and weathering, but also the virgin stress field. This paper presents an application of a numerical method to investigate the effect of the virgin stress on slope stability. The finite element method is employed to simulate the excavation of open pits. Redistributed stress fields in the slope of open pit are computed for several different virgin stress fields. Based on the redistributed stress fields, the shear force which tends to produce sliding of a rock mass and the frictional resistance to sliding are evaluated. The possibility of potential failure is assessed by the limit equilibrium method. The combination of the finite element method with the equilibrium method provides a powerful analytical tool for slope stability. The significant effect of virgin stress on the stability of slopes is shown by studying a typical case.

Jan 1, 1989