Search Documents

By Charles L. Mantell, James E. Hoffmann

Mechanical inclusion, electrophoretic deposition, and adsorption were studied as mechanisms for code-position of aluminas present in copper-plating electrolytes as an insoluble disperse phase. Mechanical inclusion was not a significant factor. That codeposi-tzon of aluminas by an electrophoretic mechanism was unlikely was substantiated by measurements of the potential of the aluminas. The alumina content of the deposits was studied as a function of the pH of the bath. These tests in conjunction with sedimentation studies demonstrated the absence of an isoelectric point for the alutninas over the pH range examined. Thiourea in the electrolyte (a substance known to be adsorbed on a copper cathode during electrodeposition) affected the amount of alumina in the electrodeposit. However, no adsorption of thiourea on aluminas in aqueous dispersions was detected. If it were possible to produce a dispersion-hardened alloy of copper and alumina by electrodeposition, an alloy possessing both strength and high conductivity at elevated temperatures might be anticipated. Investigation of the mechanism of codeposition of aluminas with copper was undertaken with the hope that knowledge of the mechanism would aid in the development of such an alloy. The word "codeposit" here does not necessarily imply an electrolytic phenomenon but rather that the materials codepositing, the various aluminas, are transported to and embedded in the electrodeposited copper by some means. Mechanical inclusion in electrodeposition implies a mechanism of codeposition which is wholly mechanical in nature; the only forces acting on a particle are gravity and contact forces. Such a particle is presumed to be electrically inert and incapable of any electrical interaction with electrodes in an electrolytic plating bath. Processes for matrices containing a codeposited phase by electrodeposition from a bath containing a disperse insoluble phase frequently state that code-position is caused by mechanical inclusion.10,2,12 If settling, i.e., gravity, be the controlling mechanism for codeposition of aluminas, then assumptions may be made that 1) the content of alumina in the electrodeposit should be enhanced by increasing the particle size, 2) the geometry of the system, that is, the disposition of the cathode surfaces relative to the di- rection of the falling particles, should affect the alumina content of the electrodeposit, 3) in geometrically identical systems the chemical composition of the electrolyte employed should exercise no effect on the alumina content of the deposit, that is, the alumina content should be the same in all cathode deposits irrespective of bath composition. A bent cathode19 evaluates the clarity of filter effluent in electroplating baths by comparing the roughness of the deposit on the vertical surface with that on the horizontal surface. Two difficulties are inherent in this technique: 1) the current density on the horizontal portion of the cathode would be substantially greater than that on the vertical surface; 2) should the deposit obtained be rough, projections on the vertical face could act as horizontal planes and vitiate the relationship between the vertical and horizontal surfaces. Bath composition should have no substantial effect on the alumina content of the deposit. Two different electrolytic baths were employed. They possessed variant specific conductances and substantially different pH ranges. The experimental tanks were rectangular Pyrex battery jars 6 in. wide by 3 1/4 in. long by 9 3/4 in. deep. The cathodes were stainless steel 316 sheet of 0.030 in. thickness, cut to 7.5 by 1.75 in. and bent at right angles to form an L-shaped cathode whose horizontal surfaces measured 1.75 by 3.0 in. All edges and vertical surfaces were masked with Scotch Elec-troplaters Tape No. 470. The anodes were electrolytic cathode copper 9 in. high by 2.25 in. wide by 0.5 in. thick. To eliminate inordinately high current densities on the projecting edge of the cathode, the anode was masked 1 in. above and below the projected line of intersection of the cathode with the anode. The exposed area of the anode was equal to that of the cathode, providing both with equal average current densities. The agitator in the cell was of Pyrex glass and positioned so its center line was equidistant from cathode and anode, and a plane passed horizontally through the center of the blade would be located equidistant from the bottom of the cathode and the bottom of the deposition tank. The assembled apparatus is depicted in Fig. 1. Hatched areas on anode and cathode represent the area of the electrodes wrapped with electroplaters tape. MATERIALS The chemicals were copper sulfate—CuSO4 • 5H2O— technical powder (Fisher Scientific Co.). Spectro-graphic analysis showed substantial freedom from antimony, arsenic, and iron. Traces of nickel were present.

Jan 1, 1967

R. E. Powers (Mellon Institute of lndustrial Research, University of Pittsburgh, Pittsburgh)—Several of the processing methods at the Josephtown smelter might well be considered by plants producing iron blast furnace sinter. In making blast furnace sinter the objectives are much the same as at Josephtown: To produce a strong yet porous agglomerate which has a size consist in a preferred range. The emphasis however is on production rate rather than on the size or other quality characteristics of the sinter. Therefore the technique is entirely different. Blast furnace sinter plants attempt to make their product in one pass with a minimum recirculating load and without sizing treatment after the sinter leaves the machines. Many plants are beginning to feel that more attention paid to quality characteristics would make the product a more desirable blast furnace material. The pelletizing of very fine material before placing it on the bed is not deliberately done at iron sinter plants, although the installed equipment sometimes gives a simila; action. Such pelletizing seems to be a promising way of accommodating the down-draft sintering Drocess to very fine materials. he recirculating load at Josephtown is extremely high. Two plants' producing blast furnace sinter from raw material of comparable size have a recirculating load of about 100 pct of production. At Josephtown it is notable that the size and the rate of feeding of return fines are under control. This is not the case in most blast furnace sinter plants. The sinter slicer appears to be a worthwhile aid in effecting such control. It is similar in action to rakes and plows used at a number of plants, but it has the advantage that the sinter dislodged is positively removed and not left to the inefficient action of a stationary grizzly screen. Blast furnace size specifications for sinter are not at present so rigid as the Josephtown specifications. If the sizing of blast furnace sinter does become important, then the Josephtown crushing practice, in which a large recirculating load is maintained on the crusher in order that minimum fines be produced, may be of interest. H. K. Najarian (authors' reply)—We note that Mr. Powers appreciates some points that we tried to emphasize in our paper as being of importance in making zinc sinter of good quality and which may well be applied to iron blast furnace sinter. Fig. 2 shows the pelletized nature of the feed going on to a Dwight-Lloyd type sintering machine in our plant. Practically, the entire feed consists of more ,or less rounded particles which permit more uniform air passage through the charge, while the larger particles in the charge roll on to the surface of the grate, which helps to keep the grate openings from being clogged by excessive fines. An agglomerated charge of this character may preferably be made by rolling action while being mixed in a rotating drum and wetted by water sprays to bind the fine particles together and give the charge the desired moisture content. From our observations of several iron ore and blast furnace flue dust sintering operations, we believe that if the fines from the sinter discharged from the machines were to be recirculated and agqlomerated with the new feed, not only sinter of better quality but larger capacity from the machines may be realized.

Jan 1, 1952

By H. A. Hoffman

Competition from an all-flotation plant, with demonstrated economies and efficiencies, plus a change in smelting contract and introduction of improved cyclones lead to conversion from gravity-flotation. Detailed descriptions are given of equipment installed and procedures used at St. Joseph Lead's Federal mill. Future plans include further quality control by instrumentation in all aspects of the mill operation. Also planned are improvements in materials handling systems. Competitive conditions will continue to dictate improvements and changes in the mill flowsheet. The advent of all-flotation mills in the Lead Belt was introduced by the Indian Creek mill in late 1953. This modern and efficient plant then became a pattern for the other mills in this area to re-evaluate their circuits in an effort to develop flowsheets that would improve operating conditions and metallurgy. The Indian Creek mill demonstrated that all-flotation would require considerably less operating and maintenance labor than the combination of tabling and flotation that was common in the Lead Belt at that time. Two significant changes occurred in recent years to allow all-flotation to be seriously considered in other Lead Belt mills. One was a change in the smelting contract which did not require gravity concentrate. Another was the development of cyclones which provided classification of the flotation feed in a very small space. Since the Federal mill was the largest concentrating plant in the Lead Belt it was felt that the greatest savings could be made by investigating the all-flotation possibilities at this mill. Interest was stimulated by the milling and ore dressing Depts. to determine if this mill would be converted without undue cost, provided the metallurgy could be improved. Accordingly, laboratory tests were initiated to learn what metallurgical benefit could be derived. Numerous tests were run which indicated that grinding to all-flotation would improve the tailing by as much as 0.02 pct Pb. This was quite significant when multiplied by the tonnage of ore treated. Projecting the added cost of power for extra grinding and flotation, and the additional flotation reagents required, plus additional new equipment that would have to be purchased, it would still add up to a considerable saving. The all-flotation mill would reduce man power by some 30 pct, and make a metallurgical improvement. Operating costs could be reduced bv 2$ per ton. The metallurgical improvement would amount to 4$ per ton, for a total of 6$ per ton of ore milled. An estimate of the cost of the conversion was set at $250,000. With the savings as estimated this could be paid off in about two years. On paper it therefore seemed attractive enough to justify a mill test. MILL TESTING One section of the Federal mill was made available for use as a separate test circuit. Cyclones and density controllers were borrowed from the Viburnum and Indian Creek mills. Denver flotation cells were obtained from the Desloge mill that was then shut down. Two 10-cell groups of Fagergren flotation machines, consisting of eight roughers and two cleaners in each bank, were segregated from the remainder of the plant. The 9x12-ft rod mill was continued as a primary grinding mill. The two 6%x12-ft mills on this section were converted from rods to balls, and the speed increased to 22.0 rpm. Cyclones were installed to close the circuit of these ball mills. The ground pulp from each of the ball mills was fed separately to its own bank of flotation cells so that two completely separated test circuits could be run in parallel. This test circuit operated on a three-shift basis from Dec. 22, 1959 to Mar. 21, 1960. The first few weeks were occupied in developing conditions for proper metallurgy and trouble-free operations. Results were rather erratic but as the ore dressing laboratory and the mill operators became more familiar with conditions they were able to obtain expected results, which could be duplicated day after day. The last five weeks of testing indicated the best results and are tabulated in Table I. During the first two weeks a Denver unit cell was used on No. 1 flotation circuit. Even though it recovered almost one half of

Jan 1, 1962

By Donald H. McLaughlin, Reno H. Sales

ADAPTATION to mining needs of the rich store of geologic knowledge concerning mineral deposits and the application of principles of the science to specific problems in the finding, development and stoping of particular ore bodies are the major tasks of the mining geologist. On him to an increasing degree is placed responsibility for estimation of ore and appraisal of mineralized ground, for explicit guidance of exploration and development, and for reliable advice with regard to the many geologic conditions that influence mining operations. In the long continued and steady efforts to meet these requirements, a special skill in close observation, recording, and quantitative interpretation has been developed, particularly by geologists on staffs of mining companies, which in many districts has proved to be effective, not only for technical ends, but also for advancement of scientific understanding. The foundations for mining geologic work were laid in most districts of the West by investigations of the United States Geological Survey. For years they have provided a reliable basis for geologic thought with regard to ore deposits, and later studies have enriched and supplemented rather than superseded them. In very few districts have the geologic relations stated in the earlier papers needed serious modification or revision, in spite of new evidence subsequently made available in abundance by mining exposures. Indeed, one of the chief satisfactions derived from success in mining geologic work is the assurance that it gives of the correctness bf the major concepts of the science of ore formation, established to so large an extent by the leaders of this notable group among whom Lindgren has been so eminent a figure. The geologists of the Survey have given and are continuing to give the service which can properly be expected of the Federal government. Their work, however, though of the greatest value in establishing the broad geological setting,

Jan 1, 1933

By Samuel S. Wyer

Over 8,000,000 people in the United States depend on natural gas for their cooking, heating and lighting service. This service has been made possible only by the investment of large amounts of capital in transportation lines connecting the gas wells to the various communities, thus combining a hazardous mining operation with a public utility service. The effect that making these lines " common carriers" will have on the present and future service to these 8,000,000 or more people is of far reaching ethical and economic importance, and deserves careful consideration. As an introduction, it must be conceded that: 1. Natural gas, although a mineral and obtained by a mining operation—with more uncontrollable and uncertain features to cope with than exist in the mining of coal or other minerals—when served to the public becomes a public utility service. 2. The governmental power to regulate all public utilities in the interests of the public cannot be successfully disputed. 3. Mere suggestion of inconvenience to the utility is wholly irrelevant, as it cannot be considered or allowed to influence in making a defense against governmental regulation. Unfortunately it is not generally appreciated that:.. I . 1. Legislative enactments are not necessarily laws, and cannot abrogate economic laws or alter engineering facts. 2. There is a clear distinction between "common carrier7' and "public utility," although the terms are frequently confused. "A common carrier is one who undertakes for hire to transport persons or goods, or both, from place to place for all persons indifferently, the term implying indifference as to whom shall be served, and an equal readiness to serve all who apply, in the order of their application." On the other hand, property becomes a "public utility" only "when for a particular purpose the public have a right to resort to the premises and make use of them." It is, therefore, important to note that not all public utilities can be regarded as common carriers. The U. S. Supreme Court has already

Jan 1, 1915

By P. W. Ramsey, D. P. Kedzie

INCREASING demand for improved strength-weight ratios made on aircraft structures has resulted in a gradual increase in the tensile strength requirements for steels used in such applications. As the cyclic loads often are more critical than static loads, and the fatigue properties are generally the design criteria, the question arises as to whether an improvement in fatigue properties accompanies the increased tensile strength. The present investigation was undertaken to determine the relationship between fatigue and tensile properties for an aircraft quality steel in the 155 to 280 ksi (1000 psi) tensile strength range, using the Prot method of fatigue testing. Procedure and Results After preliminary work to establish proper heat treating procedures for this heat of aircraft quality electric furnace steel (a Ni-Cr-Mo-V steel," AMS- Prot Fatigue Testing Method—The determination of the endurance limit by the conventional Wohler method can be time-consuming and easily require 20 specimens when statistical variance is to be established. This is also true when endurance limit loads are determined on actual parts or subassem-blies, and the desirability of a reliable accelerated method has been evident for some time. The primary advantage of the Prot method of fatigue testing is in reducing the number of specimens and the time required for each test. Unlike the Wohler method, every Prot specimen tested con- tributes to the determination of the endurance limit, and the authors have been able to duplicate Wohler results obtained with 20 specimens with only half the specimens and a fourth of the total cycles. This new technique for defining the endurance limit was proposed in 1948' by Marcel Prot and consists of progressively increasing cyclic stress until fatigue failure occurs. By varying the load rate, a, a useful relationship is found to exist with failure stress, so that for steel the failure stress appears to

Jan 1, 1958

By Jerome F. Kuzmick

Many investigations have been made on the effect of the variables of pressure, sintering temperature and sintering time on the physical and microstructural charactcristics of metal-powder compacts. Severa1 such investigations have indicatcd that pressure is the least important of these three factors in an attempt to secure a dense. strong compact by a simple coltl-pressing and sintering procedure. However, it was felt that a further study of the effect of pressure on pressed and sintered metal powder compacts might prove interesting, for the following reasons: In work done in the past on the effect of pressure, temperature. arid time, the, metal-powder compacts were subjected to long sintering periods, and temperatures right up to the melting point of the metal were applied. It was thought that pressure might exert a more profound effect under short-time simtering and within narrower ranges of temperature. such as normally would be applied in large-scale production of metal-powder parts. 2. It was hoped that something further might be learned of the nature of the bond in pressed and sintered metal-powder compacts. 3. It was thought that interesting infor mation concerning the work-hardening effect of pressure on the crystal structure. of sintered metal-powder compacts would be obtained. Procedure Rectangular bars, 2 by 1/2 by 1/4 in. were molded from the following metal powders: Atomizcd till powder, 325-mesh Atomized aluminum powder, 325-mesh Reduced copper powder, 100-mesh Electrolytic iron powder, 100-mesh Atomized 70-30 brass powder, l00-mesh The, till powder was molded at various pressures up to 40 tolls per sq. in. This was the maximum, because at higher molding pressures there was considerable extrusion of tin into the die wall, jamming the die plungers. The tin specimens were not -in tered, as this phase of the work was- done merely to see how much a very sold metal could be compressed. The aluminum powder was compressed at various pressures up to 50 lons per sq in. Higher pressures could not be used because of extrusion into the die wall The compacts were sintered one hour at 000 in pure dry hydrogen. The copper powder was molded at vari-ous pressures up to 96 tons per sq. in. One set was sintered at 750°C., another at 050 C. for one hour in pure dry hydrogen. The electrolytic iron powder was molded at various pressures up to 00 tons per sq. in. and sintered, one set at Soo°C and one set at 1300°C for one hour in pure dry hydrogen. Extra 325-mesh specimens were also prepared to study the effect of reduced particle size on grain structure. The brass powder was molded at various pressures up to 96 tolls per sq. in. and silltered for one hour. one set at 65o°C. and one set at 800°C, in pure dry hydrogeu.

Jan 1, 1945

By Edmund Davenport

Tier; production of thorium of high purity by the Ca-CaCl2 reduction has been described by Marden and Rentschler,1 who also reported some of the properties of the coherent, ductile metal obtained from this pure thorium powder. The present paper describes the properties of thorium produced by the Ca-CaCl2 process modified in some details to meet commercial conditions. The principal effect of these changes in process has been an unavoidable increase in the oxide content of the thorium.

Jan 1, 1929

By Gail F. Moulton

The production of petroleum in Illinois in 1928 was approximately 6,500,000 bbl., a decline of about 500,000 bbl. from the previous year and of about 1,500,000 bbl. from 1924. Production increased about 200,000 bbl. in Indiana to slightly less than 1,000,000 bbl. Production for 1929 is estimated at approximately 6,000,000 bbl. for Illinois and 1,000,000 bbl. for Indiana. Illinois Because production from most of the wells in the state has declined to a small daily average and the low prices for crude oil discouraged wildcatting, the number of wells drilled fell below that for any previous year since the development of commercially important production in the state. The Ohio Oil Co. discovered a pool of apparent commercial importance in southwestern Illinois near Dupo, in St. Clair County, and favorable showings of oil were encountered in a well in southeastern Illinois, near Harrisburg in Saline County. New production from the Dupo area is expected to check the rate of decline for the state. Thc following tablel summarizes field developments for 1927 and 1928 (for important detail by counties see notes at foot of table): 1027 1928 Completions........................................... 162 145a Initial production, bbl.................................. 2244 1840b Dry holes........................................,.... 66 58" Gas well completions................................... 13 8d 0111 wells abandoned.................................... 45" a Crawford, 44; Lawrence, 28; Wabash, 40. b Crawford, 501; Lawrence, 403; St. Clair, 165 (4 completions); Wahash, 668. o Crawford, 12; Wabash, 19. d Crawford, 6. b Lawrence, 21; Wabash, 15. The discovery well in the Dupo field in St. Clair County, produced about 150 bbl. per day from the Trenton lime at 660 ft. It is located in a northern extension of the Columbia-Waterloo anticline on which the Waterloo pool was developed in 1921. The best information on the.

Jan 1, 1929

By W. E. Coughlin, R. L. Faverty, F. H. Lightner

The intent of this paper is to present the general strategy and method of implementation to achieve a "fast-track" mine development. The major objectives of a "fast-track or rapid development schedule are to minimize front-end development expenditures and to realize an early cash flow from operations. The Borealis project of Houston International Minerals Corp. (HIMCO) is used as the working example to illustrate the development schedule. Borealis is a 2.9 kt/d (2,500 stpd) gold-silver heap leach operation near Hawthorne, NV.

Jan 1, 1984

A recent study estimates that a 10% improvement in the performance of wire rope used on draglines could save the US coal industry $2 million annually in rope costs. In addition, such an improvement could boost annual coal production by allowing the industry's draglines to remove an extra 1.5 million m3 (2 million cu yd) of solid overburden each year. These findings, although admittedly preliminary, suggest the magnitude of benefits that can be derived from a well-planned wire rope maintenance program.

Jan 3, 1978

By R. J. P. Lyon

It is usually assumed1,2 that ore deposition is relatively slow, taking place over tens of thousands of years. Yet many syntheses and phase changes can be completed in the laboratory in a matter of hours, under essentially the same pressure and temperature conditions to be expected in nature. Much has been written about geothermometry, and Ingerson's recent summary2 can hardly be surpassed. Rather than review the whole field, this article will deal specifically with diffusion rates in solid solutions* of the sulfide minerals.

Jan 11, 1959

By C. J. Bechtoldt, H. C. Vacher

Quenched alloys, prepared by powder metallurgical techniques, were examined by microscopic and X-ray diffraction methods. The compositions and heat treatments were chosen so that the chromium and nickel solvuses could be determined and a range of composition and temperature, in which a eutectoid had been reported, could be explored in small intervals. The results showed no evidence of eutectoid reactions having taken place. ALLOYS containing iron, chromium, molybdenum, and nickel are extensively used in high-temperature applications. In order to provide basic information on the solid-state reactions that occur in such alloys, the National Bureau of Standards is engaged in an extensive study of the equilibrium phases in the binary, ternary, and quaternary systems involving these four metals. Attention was directed to the chromium-nickel system because a review of the literature showed conflicting data. A recent compendium1 of the constitution of binary alloys gives two diagrams for the chromium-nickel system, one a simple eutectic and the second a diagram showing a eutectoid and a eutectic. The eutectoid was the result of an allotropic transformation in a high-temperature solid-solution form of a chromium-rich phase called 0. The approximate temperature and composition of the eutectoid was 1200°C and 30 at. pct Ni. In the preliminary study, at the Bureau, no transformation was indicated in the chromium-rich phase of ternary and quaternary alloys in which chromium and nickel were major components. Similar results have been reported from time to time in the literature,2-8 In consequence of this situation, a systematic study was made of the constitution of heat-treated chromium-nickel alloys using metallographic and X-ray diffraction methods. The compositions of the alloys were selected so as to determine the boundaries of the chromium-rich and the nickel-rich phases and to explore in small intervals the ranges in composition and temperature in which the eutectoid had been reported. The results of this study are reported and discussed in the present paper. EXPERIMENTAL PROCEDURES Materials, Alloys, and Heat Treatments—The alloys were prepared by a powder metallurgy technique similar to that used in earlier work.9 Analyses of the materials used are given in Table I. Powders were mixed using a vibrator in 30-g batches of predetermined composition; 2-g pellets were made from the mixture by compacting at room temperature in a 1/2-in. diam mold under 60,000 lb per sq in. pressure. The pellets were sintered in dry hydrogen for 10 days at 1300°C. At the end of the sintering treatment the specimens were quenched in water, which caused a pale green film to form on the chromium-rich alloys and thin black scale to form on the nickel-rich alloys. The pellets after sintering were approximately 1/2 in. diam by 3/32 in. thick. The purification train9 was modified by inserting a tube of titanium turnings, heated at 700°C to increase the efficiency of the removal of oxgen and nitrogen. It was found in the earlier work that the sintering treatment lowered the carbon, oxygen, and nitrogen contents of chromium-rich alloys to 0.01, 0.01, and 0.004 wt pct, respectively, and that there was a loss of chromium. In order to ascertain the extent of this loss, the chromium contents of certain alloys were determined chemically. They included those alloys used to determine the parameter-composition curves and those of critical composition, used to determine the chromium-solvus microscopically; these analyses were made on samples after the final heat treatments. The mixed powder values for the chromium content of those alloys that were not analyzed were adjusted to conform to a smooth curve based on the chemically analyzed values for

Jan 1, 1962

By A. R. Elsea, E. E. Fletcher

Cast X-40 alloy with the lowest nitrogen content studied had a 100-hr rupture stress at 1500°F about equal to the reported value for the commercial alloy. Increases in nitrogen content progressively decreased the rupture strength, and with about 0.1 to 0.2 pct N a minimum strength was reached, but there was no accompanying change in microstructure. Further increases in nitrogen resulted in the fomzation of progressively increasing amounts of a lamellar, pearlitic-type structure at the grain boundaries, with accompanying increases in rupture strength, and above about 0.25 to 0.33 pct N, the rupture strength exceeded the normally reported values. Two series of melts representing different melting stocks exhibited minimum rupture strengths at different nitrogen contents. This suggests that some unidentwed trace element not removed by vacuum melting has a strong influence on the response of this alloy to variations in nitrogen content. In a series of melts with manganese contents ranging from 0.6 to 3.2 pct, the material with the lowest manganese content had the highest 100-hr rupture strength at 1500°F. The manganese variations had no appreciable effect on the microstructure. CAST cobalt-base alloys such as X-40* exhibit high strengths at elevated temperatures (1500°F and above), but they also show considerable scatter in high-temperature properties. Since the design of parts for critical applications must be based on the minimum expected properties, this broad scatter appreciably lowers the design strength of the alloy. If the relatively poor properties exhibited by a few test parts from any given group could be improved, the spread in properties would be narrowed, and the design stress could more closely approach the average expected properties. The purpose of this research investigation was to learn what were the causes of these erratic properties and, if possible, to find methods for eliminating them. Earlier unpublished work showed that vacuum melting markedly influenced the high-temperature strength of cast X-40 alloy. There were indications that this behavior may have been the result of changes in the nitrogen or manganese content of the castings. Consequently, in the current investigation, the influence of variations in nitrogen and manganese content on the structure and high-temperature properties of cast X-40 alloy was studied. In this program, X-40 melting stock was vacuum melted to produce a base material that was very low in nitrogen content and in volatile trace elements. Additions were then made to this base material to produce alloys of the desired composition. The metal was cast into investment molds producing coupons which were machined into stress-rupture bars. These bars were subjected to stress-rupture tests and me-tallographic study to determine the influence of changes in analyses (nitrogen and manganese content) on the structure and properties. Material—The melting stock used for these experi-ments was in the form of shot from two master heats of commercial X-40 alloy. Only one master heat was used in a given series of melts. Thus, any differences in structure or properties that showed up in the specimens from a given series would be the result only of the intended variations in composition. The certified analyses of the master heats were as follows: C Mn Si Cr Ni Lot No. 2 0.50 0.71 0.66 25.44 10.53 Lot No. 3 0.54 0.73 0.70 25.95 10.00 W Fe Co P S Lot No. 2 7.45 1.34 Bal. 0.011 0.013 Lot No. 3 7.58 1.53 Bal. 0.005 0.016

Jan 1, 1960

By K. Mukherjee

Instantaneous resistance change during martensitic transformation in Fe-30 at. pct Ni alloy has been studied using a low-noise electronic system. The smallest signals recorded in this investigation were of the order of 10 pv. These small signals did not show the initial increase reported by earlier investigators to support a double shear mechanism.&apos; A variety of pulse shapes and sizes was observed during "burst" transformations, and these signals were neither a linear function of the size of martensite plates nor of the volume fraction transformed. Even the smallest signals, presumably from single plates, showed complications resulting from elastic and/or plastic deformation, shock wave propagation, and so forth, which are inherent in the growth process of a martensite plate. The time of formation and interface velocity determined froni this experiment agree very well with the pioneering work of Bunshalz and Mehl.&apos; AN Fe-30 at. pct Ni (c0.005 pct C) alloy was used to study the time of formation of martensite plates. Martensitic transformations, unlike the nucleation and growth processes, are usually characterized by an extremely fast reaction rate. During the transformation, the crystal structure changes and this change is propagated through a finite volume of the parent crystal lattice within a very short time interval. The interface between the two phases probably consists of moving dislocations, and the time of formation of the plate depends on how fast this dislocation interface can move. Knapp and Dehlin~er or Cottrell and Bilby mechanisms, or similar dislocation models, can be used to calculate the time of formation of a martensite plate of a given size. In the past, conventional photographic technique475 as well as electrical resistivity techniques"~-" have been used to measure the time of formation of a martensite plate. The specific resistance of the martensitic phase in Fe-30 at. pct Ni alloy is lower than that of the austenite phase. Therefore if a current is passed through a small austenite sample in series with a large external resistance, then one would observe a voltage change across the sample as martensite is formed. Such dc measurements are shown in Fig. 1. The initial large voltage drop in Fig. 1, at the M, temperature, is due to a "burst" transformation where a large number of plates are formed in a cataclysmic manner within a very short interval of time. Even during the later stages of transformation as shown in Fig. 1, one can observe discontinuous voltage changes due to small bursts. In order to resolve the time scale of such discontinuous stages, the voltage signals are amplified and fed into a highspeed oscilloscope. In this investigation a low-noise amplifier was used for the first stage of amplification. The signal to noise ratio was further improved by the design of a pulse transformer. This transformer was capable of amplifying the signal by a factor of six. Voltage signals were studied over a wide time scale ranging from 2 sec to 0.1 psec. I) EXPERIMENTAL PROCEDURE A) Specimen Preparation. Specimens were cut from induction-melted Fe-30 at. pct Ni (<0.005C) alloy and cold-rolled to 0.2 by 1 mm cross section and an average length of 5 cm. During mechanical shaping, the specimens were strain-annealed at 950°C for 24 hr in vacuum. Finally the finished samples were vacuum-annealed at 1000°C for 6 hr and water-quenched to room temperature. The average grain diameter was 0.02 cm. B) Cooling System. The M, temperature of the alloy was -55°C. Fig. 2 shows the arrangement which was used to cool the specimen at a slow rate. The specimens were mounted inside a i -in.-diam hole in the 2-in.-long section of the copper specimen holder. This cavity was filled with silica gel. A dummy specimen was used under identical conditions for

Jan 1, 1969

By L. Burris, C. H. Stockman, I. G. Dillion

Zone melting is a purification process in which separation of impurities is effected by slowly moving a narrow melted zone through a bar of solid material. Equations are presented which 1—predict the concentration profiles after successive passes of the zone and 2—give the limiting distribution of solute along the bar after an infinite number of passes of the molten zone. These equations take into account the effect of normal freezing in the last zone length. These equations were solved numerically using an electronic computer, and the concentration profiles are presented as a function of the solute distribution coefficient and the ratio of molten zone to total bar length. ZONE MELTING is a purification process in which separation of impurities is effected by slowly moving a narrow melted zone through a bar of solid material. Separation occurs if the solid freezing from a solution at any moment has a composition different from that of the liquid from which it is freezing. Solutes which lower the freezing point will tend to remain in solution and will be moved in the direction of zone travel. Solutes which raise the freezing point will preferentially freeze out, and they will be moved in a direction opposite to that of zone travel. After repeated unidirectional passage of a molten zone through a bar of material, impurities will be concentrated in the ends of the bar. A limiting concentration gradient will be reached in the bar after a large number of passes of the molten zone. Both the magnitude of this limiting concentration gradient and the rate of movement of solute in any pass depend on the zone length and on the equilibrium concentrations of solute in the liquid and solid phases. The basic theory of zone melting was thoroughly covered by Pfann.1 The purpose of this paper is to extend the theory of zone melting by presenting 1—equations which relate the concentration profiles in successive passes of the zone and 2—equations which give the limiting distribution of solute along the bar after an infinite number of passes of the molten zone. These equations take into account the effect of normal freezing* in the last zone length concentration of a given solute in the solid to the concentration of the same solute in the liquid. Analytical methods for determining the concentration profiles after any pass have been developed by Lord2 and Reiss. The method developed by Lord does not take into account normal freezing in the last zone and also becomes very complicated when the number of passes becomes large. The method developed by Reiss enables the direct calculation of the complete concentration profiles (including that in the last zone) after any pass for values of k close to unity (0.9 < k < 1.1). Both methods are useful and provide valuable insight into the zone melting process. The equations given in this article are based on the same assumptions used by Pfann. These are: 1—uniform composition in the liquid, 2—negligible diffusion in the solid, 3—constant distribution coefficient, 4—constant length of the liquid zone (except at the ends), and 5—solubility of the solute in the melt is not exceeded at any point. Equations for Concentrations in Successive Passes For a melted zone of length 1 at the left-hand end of a bar of uniform unit cross-section, the amount of solute in the liquid is J0Cn-1(x) dx [1] where the subscript is the number of the pass. Cn-1(x) represents the concentration (expressed as weight per unit volume) obtained in the previous

Jan 1, 1956

By R. R. Boucher, O. J. C. Runnalls

A pronounced thermal effect has been observed on heating or cooling a1wninum-rich Al-U and Al-Pu alloys. From microscopic and X-ray diffractionstudies, the effectl has been attributed to trnsfor)nations in the inlemetallic phases UAl, and PuAl , involuing rearrangement or cluslering of vacancies The transformation obsrved in Al-20 wi oct U alloys occurred near the a Al-UAl4 eutectic tem-perature of 646°C making it difjicult to detect from heating curves. When cooling, howeoer, thermal mad X-ray analyses indicnted that the high-temperati~re phase labeled p UAL, precipitated initially during euitectic solidification. As solidification continued and after an induction period o-f 5 lo 20 tnin the nu-cleatiorz and growth of the low- twmperature phase, a UAl4 produced an euolution of energy which raised the observed alloy temperature by 1° to 2°C. in Al-Pu alloys the transformation occurred at 645°C, 5 deg below the eutectic solidification temperccture. The eslimated latent heat of transformation was 25 +5 cnl per g PuAl,. The high-tetnpevcl-ture forms of UAl, and PuAl, were easily 9-etccined by chill casting Al-U and Al-Pu alloys and on reheating the alloys the trcltzsforrnation to the a phase was sluggish even above 600°C. Separated single cryslals o-f UAl4, joy example, showed no evidence Of transformalion after heating for 16 hr at 620°C. The transformation rates increased yapidly enough with increasing temperature, however, that a a spontaneous liberation of energy lens observed on occasion when bealing cast Al-20 wt pet U to neal- the RECENT phase studies on A1-Pu alloys have indicated that earlier reported equilibrium diagrams should be modified to take account of several poly- morphic transformations in the intermetallic compound PuAl,.&apos; During the course of the latter work an unexpected heat evolution was observed while cooling a solid alloy consisting of a mixture of a aluminum and PuA1,. The evolution occurred at 645°C, y below the a A1-Pu A1, eutectic solidification temperature. Subsequent thermal-analysis experiments with A1-U alloys showed that heat was evolved there also at a temperature nearly coincident with the a A1-UA1, eutectic solidification temperature of 646°. A search of the literature revealed that similar thermal effects had been observed before for both A1-U and A1-Pu but had never been fully explained.2,3 The purpose of the present paper is to describe thermal-analysis and X-ray diffraction experiments which have led to the conclusion that the thermal effects are due to transformations which involve the rearrangement of vacancies in the intermetallic compounds UA1, and PuA1,. EXPERIMENTAL PROCEDURE The A1-U alloys were prepared by heating super-pure aluminum (99.99 pct +) obtained from the Aluminum Co. of Canada in a graphite crucible surrounded by an induction coil. At 1000°C high-purity uranium metal produced by the Eldorado Mining and Refining Co., Ltd. was dropped into the liquid aluminum and was dissolved completely within 15 min. The impurities in the uranium were A1—4 ppm, Ca-4, C-70, Cr-3, Cu-6, Fe-30, Mg-2, Mn-10, Ni-25, Si-25, and Zn-2. The A1-Pu alloys were prepared by reacting plutonium dioxide with liquid aluminum under cryolite (3 NaF . AlF,) for 10 min at 1100°C in graphite crucibles exposed to the air. The plutonium was 99.8 pct pure, containing trace impurities of Ca, Cu, Fe, Pb, Si, and Zn. The liquid alloys were usually poured into water-cooled molds to provide castings of uniform composition from which samples could be cut for heat treatment and thermal-analysis experiments.

Jan 1, 1965

By R. L. Segall

AN unusual thermal etch figure in copper is described and an explanation in terms of twinning is suggested. A flat polycrystalline specimen of OFHC copper cut from a rolled sheet was electro-polished in orthophosphoric acid and annealed at 950°C in a vacuum of approximately 10-3 mm Hg for 2 hr. The specimen was found to be thermally etched, the markings on the surface being consistent with the assumption that they were the traces of the (111) planes which are developed preferentially because they have the lowest free energy. However, on one grain (the grain shown in Fig. 1) the traces formed an almost regular pentagon and at first sight it seemed unlikely that they could all be (111) traces. These traces were studied further because it was thought that they might be a type of growth spiral. A fringe pattern showed that this was not so, the grain being sensibly flat and the only features having steps were the striations and the faint curved line passing out from the center of the pentagons. To obtain some additional information, the specimen was deformed in tension. The effect of the stress was first to cause the appearance of lines running from the centers to the apexes of the pentagons and then to tilt the five segments so formed. At a much greater stress, appreciable slip appeared on the grain; these effects can be seen in Fig. 2. The micrograph was taken at a fairly late stage in the deformation and the tilting is quite marked. The magnification is the same as in Fig. 1, and although some slip can be seen it could be observed better by varying the illumination and using higher magnifications. In each segment of the grain, slip (which takes place on the (111) planes) was parallel to the side of the pentagon in that segment. The marked changes in direction of slip from segment to segment seemed to be incompatible with the presence of a regular array of subgrains. These results suggest that some of the five segments were twins. If this is so, since the twinning plane in copper is the (111) plane, the radial lines must be traces of the (111) planes on the surface. From the symmetry of the striations about the radial lines, these planes must be almost perpendicular to the surface. The angle between <III>directions in face-centered-cubic copper is 70&apos;32&apos;. If, in Fig. 3, OAB (triangle 1) is taken as matrix and OA, OB are (111) planes viewed edge on, then AB is in the correct direction to be the trace of either of the other two (111) planes on the surface. If triangle 2 is the twin (about the (111) plane perpendicular to the surface and containing OB) of triangle 1, then once again it can be shown that all lines are traces of (111) planes. Similarly, triangle 3 is the twin of triangle 2, 4 of 3, and 5 of both 4 and 1. (The sequence is, of course, quite arbitrary.) However, if this were the case there would be a discrepancy of 7&apos;20&apos; to be accounted for. It is suggested that the faint curved line passing outward from the center of the pentagon represents either a low angle boundary or a sixth small twin. The slight step shown by the fringes at this line might be an indication that the former is the case. This explanation does not account for the coincidence of obtaining a grain whose surface must be so close to (110) and obtaining the curious twinning described previously; it would be of interest to find a specific mechanism for this.

Jan 1, 1958

By Paul B. Crawford, Bobby L. Landrum

Electrical model studies have been made of the effect of drainhole drilling on production capacity. Drain holes are those lateral holes which are sometimes drilled to assist in increasing the oil drainage into the main wellbore. The studies indicate that if the drainhole length i.r near 0.2 of the drainage radius, the increase in production capacity may be approximately 1.8, 2.08, trnd 2.33 for the case of one, two and four drain holes, respectively. If multiple drain holes are drilled, shorter holes are required to achieve a specific increase in production capacity than if one or two holes are drilled. To achieve increases in production capacities by factors near three it is shown that the drainhole lengths divided by the drainage radii must be approximately 0.64, 0.48, cnd 0.37 for the case of one, two and four drain holes, respectively. IN T RO DUCTION Kecent developments in drilling techniques have permitted the drilling of lateral or horizontal holes to increase the rate of production. The number of these drain holes may vary from 1 to 10, and they have been drilled laterally as much as 100 ft. Drainhole drilling at substantial depths is of recent origin but has been used in the Spraberry field of West Texas, the La Pas field in Western Venezuela, and certain fields in California. The diameter of the drain holes has been approximately 6 in. In drilling drain holes it is desired to know how much increase in production capacity may be expected, what additional benefit may be gained by drilling more than one drain hole, and what increase in production capacity may be brought about by lengthening the existing drain holes. In realization of the importance of lateral drilling, electrical model studies were made to provide quantitative estimates on the effect of drain holes on production capacity. ANALYSIS An electrical model was used in studying this problem. A wooden circular reservoir approximately 30 in. in diameter and 2 in. deep was filled with a dilute salt solution to a depth of 1 in. A copper band formed the periphery of the tank, and a copper wire was inserted in the center of the tank to represent the well. The drainage radius divided by the well radius was equal to 500. A diagram of this type model is shown in the inset of Fig. 1. An electrical potential was applied to the wire well and copper band at the periphery to determine the flow of current. Following this measurement copper wires of various length were soldered to the vertical wire well in such a manner as to simulate lateral wells drilled into the reservoir. Multiple lateral holes of various lengths were studied by varying the number and length of copper wires soldered to the vertical wire well. All multiple lateral wells were located symmetrically about the vertical well. The effect on production capacity by drilling an infinite number of lateral holes was studied by replacing the lateral hole with a copper disk. For each condition the flow of current was measured and compared with the flow of the vertical well only. The model which is thus described provides the steady state increases in production capacity which may be expected in some cases. The data conform to those which would be observed for a uniform homogeneous reservoir. The data may have primary application to those reservoirs producing above the bubble point. It is realized that few lateral holes are drilled in reservoirs of this type, but the data may be of some value in guiding future work or aiding to explain observed phenomena.

Jan 1, 1956

By J. S. Brown, A. G. Guy

With the exception of the work of Tammann and Hartmann,1 no published information has been found on the structural changes produced in eutectic structures as the result of heating following plastic deformation. In part this lack of information may be due to the fact that many eutectic structures contain an intermetallic compound as a prominent phase, and as a consequence have been considered to be unworkable. For example, Tammann and Hartmann were able to obtain useful data only on those alloys that they could greatly reduce in thickness by cold rolling. This restriction placed on the investigation of alloys containing intermetallic compounds has been largely removed by the work of Savitskii2 which showed that large deformations of such alloys can be produced by relatively slow compression at temperatures near the melting range. It was possible, therefore, to carry out the present work on a range of binary eutectics including one composed of two intermetallic compounds. The essential results obtained on the alloy systems studied are illustrated by the Pb-Mg eutectic containing 33.2 pct Mg, Fig 1. The cast structure, Fig la, was obtained by melting together magnesium of 99.8 pct purity and chemically pure test lead, casting into a heated, small steel mold, and furnace cooling in the mold from about the eutectic temperature. The fairly coarse eutectic structure thus obtained was too brittle to work at room temperature without cracking. Fig 16 shows the worked structure obtained by compressing a 1/2-in. cube 70 pct in about 15 sec at 550°F and then water quenching. The pronounced changes in the distribution of the two phases produced by heating the worked alloy at 850°F for 1 hr are shown in Fig lc. Recrystallization of both phases appears to have taken place, and the mechanical properties of the cast alloy must have been significantly changed by the working and heat treatment. Similar results were obtained with the Mg-59.5 pet Bi, Mg-36.4 pet Sn, Mg-65.4 pet Cu, and Bi-40 pet Cd eutectics, only the last of which could be worked at room temperature. Tammann and Hartmann reported a thickening and shortening of the needles of the eutectics which they heated about 10°C below the melting range for 1 hr after drastic cold rolling. They found the following eutectics, given the indicated amounts of reduc- tion, to have a granular structure after heat treatment: Sn-9 pet Zn (98 pet); Cd-82.5 pet Pb (60 pet); and Bi-43.5 pet Pb (90 pet). On the other hand the alloy Al-11.7 pet Si (60 pet) showed no change after heating. Tammann and Hartmann observed a distinct shrinking of the needles in unworked eutectics subjected to heat-treatment. In the present work inappreciable change in the eutectic structure was found on heating undeformed alloys. In summary, it appears that eutectic structures can be recrystallized into a "spheroidized" condition by heating near the eutectic temperature after severe deformation. If the eutectic contains one or more brittle phases the necessary deformation can be accomplished by pressing at high temperatures. It is reasonable to expect that this tendency towards equiaxed grains from the plate- or needle-like eutectic structure should be general since the energy relations and mode of growth in recrystallization are so different from those that hold for eutectic crystallization. References 1. G. Tammann and H. Hartmann: Ztsch. Melallkunde (1937) 29, 141-144. 2. E. M. Savitskii: Doklady Akad. Nauk S.S.S.R. (1940) 62, 349-351. Abstr. in Melal Prog. (July, 1949) 56, 126, 128.

Jan 1, 1950