Search Documents

By George Simkovich

It was hypothesized that solid-state point defects should alter the flotation properties of solids. Tests conducted on pure AgCl and AgCl doped with CdC12 show that atomic point defects exhibit an important role in the floatability of AgC1. Tests conducted on PbS doped with Ag2s or Bi2S3, also show that the defect structures resulting from these dope additions, i.e., a combination of electronic and atomic point defects, contribute significantly to the flotation of PbS. IT has been established that flotation occurs only when a finite contact angle exists between a solid and a gaseous bubble.' This angle, measured through the liquid phase, is expressed by the equation where the are inter facial free energies and the subscripts S, G, and L represent solid, gas, and liquid phases, respectively. As is seen in Eq. [I] three interface free energies, sG, sl, and GL, enter into the contact angle equation. Therefore, any variation in these energies which sufficiently varies the contact angle will, in turn, vary flotation processes. Changes made in any of the phases concerned, i.e., gas, liquid, or solid phase, are reflected through the changes occurring in two of the surface energy terms. Thus, a change in the liquid composition would be noted in sL and GL, and it is this phase, the liquid, which is most frequently altered in flotation studies., Changes in the solid phase must be reflected through the changes occurring in the sG and sL terms. In particular, it is hypothesized that changes in the surface concentrations of point defects in the solid-phase will alter the sG and sL terms which, in turn, will be reflected by flotation results. As an illustration of this hypothesis one may consider the defect structure and the flotation of AgC1. The bulk defect structure of AgCl is essentially one involving equal number of cation vacancies and interstitial cations.3 Upon adding CdC1, to AgC1, a greater number of silver ion vacancies are created in the bulk of the crystal.4 On the surface of the crystal the smaller binding forces and the free space accomodations may also allow for the creation of "surface interstitial anions", which will be designated as ad-anions. Thus, the point defect structure of the surface of AgCl doped with CdCl, will consist of cation vacancies and/or adanions. If the molecular forces responsible for the surface energies, ?SG and ?sL, are significantly altered by the presence of these surface point defects, then differences in flotation results will be noted as the concentration of these defects is varied. The defects present in AgCl are predominantly atomic in nature. In the case of PbS both electronic and atomic defects are present.5 This compound conducts electrically by either electrons or electron holes depending upon whether excess lead or excess sulfur is present. Upon disolving BiS3 in stoichio-metric PbS, one increases the concentration of cation vacancies and the number of electron carriers in the bulk of the crystal.5" At the surface, the possibility of ad-anions must also be considered. Conversely, upon dissolving AgS in stoichiometric PbS one increases the concentration of interstitial cations and the number of electronhole carriers in the bulk of the crystal.5,6' At the surface the interstitial cations will be designated as ad-cations. Thus, the point defect structure of the surface of a PbS crystal doped with Bi2S3 will consist of a number of cation vacancies and/or ad-anions and an excess of electrons. Conversely the point defects on the surface of a PbS crystal doped with Ag2S will consist of a number of ad-cations and an excess of electron holes. Again, as in the case of AgC1, should the molecular forces responsible for the magnitude of the interface free energies, ?sG and ?sL, be significantly altered by the presence of these surface defects then significant differences in flotation results will be noted as the concentration of these defects is varied. EXPERIMENTAL To test this hypothesis flotation tests were conducted on pure and doped AgCl and on PbS doped with either Bi2S3 or Ag2S. Preparation of the AgCl samples was performed as follows: AgCl and weighed amounts of CdC1, were melted in a porcelain crucible. The melt was then forced through a capillary tube and the particles emitted solidified in air as they fell about 1.5 meters. Spherical particles, -0.50 + 0.25 mm, were separated from the remaining solidified material

Jan 1, 1963

By A. R. Krause, C. Laird

In order to establish whether or not there is a real temperature effect in fatigue (independent of environment) , poly crystalline copper and Cu- 7.9 A1 alloy have been cycled at 298° and 7° K in vacuo and the fatigue lives compared with those in air and in liquid nitrogen. The lives of both copper and the alloy were found to be highly temperature-dependent in the absence of environment. This result casts serious doubt on the validity of the cell structure hypothesis for stage I crack propagation as presently formulated, because it predicts that there should be no such tempevnture dependence. On the other hand, the plastic blunling process is consistent with the result. Effects of environment aside, the homogenization of slip which accompanies testing at low temperature, and at low strains, seems to be the main cause for increased fatigue life. At high strain amplitudes, the fatigue lives of wavy slip materials, typically copper, are independent of temperature.' It is well-known, however, that low-strain lives greatly as as the temperature of testing is decreased. By contrast, the lives of planar slip materials, such as Cu-7.9 pct A1 alloy, increase to an even greater extent with decreasing temperature throughout both the high and low strain ranges.1'2'5 The mechanism of this temperature effect is associated with the earliest stages of fatigue failure,'" crack nucleation, and stage I growth,"' which is slow propagation along slip bands to the depth of a few grain diameters. Such life behavior has been interpreted on at least two different bases. On the one hand, those interested in the temperature effect at high strain amplitudes1 believe that stage I growth occurs by the plastic blunting process of crack propagation.7'9 They explain the effect in planar slip materials by the homogenization of slip* which accompanies fatigue testing at low temper- atures and serves both to delay crack nucleation and to decrease the rate of stage I propagation. On the other hand, Holt and Backofen,2 who have studied the effect in low strain fatigue, believe that stage I growth can be interpreted by a cell structure hypothesis.10-12 They have challenged2 the conclusion that there is a real temperature effect in this regime of fatigue testing and have interpreted the increased fatigue lives almost entirely in terms of the "environmental-protective'' effect of the liquid nitrogen and helium baths used to obtain low temperatures. This interpretation by Holt and Backofen2 may offer a means of discriminating between these two mechanisms as currently formulated and used to explain stage I growth. On the basis of the plastic blunting process applied to stage I crack propagation,7* the low strain fatigue lives of both wavy and planar slip materials should be increased with decreasing temperature. This follows because both materials show increased slip homogenization in this strain regime."13 Consequently, crack nucleation in intensified bands will be delayed and the linking of such small cracks into larger stage I cracks will be difficult. In addition, the blunting process required to lengthen a stage I crack from the order of 2 to 10 (where the strain concentration of the crack begins to overcome the slip homogenization property of the material) will also be retarded. These delays will give rise to longer lives in both kinds of material. In contrast to the blunting hypothesis, no temperature dependence has been predicted on the basis of the cell structure hypothesis, because it is well-known that materials cycled at low temperature show no differences in type of dislocation structure for a given strain amplitude.18"20 If the lives of wavy and planar slip materials do show a temperature dependence when the environment is eliminated as a variable, then it is questionable whether cell structures per se have a fundamental role in fatigue fracture. Accordingly, specimens of copper and Cu-7.9 wt pct A1 have been cycled at 298° and 77°K in vacuo and the fatigue lives compared with those in air and in liquid nitrogen, in order to establish whether or not there is a real temperature effect in low strain fatigue. Since it is difficult to measure the strains in specimens when cycled in vacuo, S-N curves have been used as the basis of comparison. In studying the influence of temperature on fatigue life in ordinary environment, Holt and Backofen2 used the superior basis of E-N curves. However, they also published S-N curves and thus established the relationship between E-N and S-N curves. This relationship is used to support the S-N comparison reported in the present investigation. EXPERIMENTAL Materials. The copper employed in this investigation was of 99.99 pct purity and the cu-7.9 pct A1 was prepared from metals of the same purity. The stock, of 3 in. initial diam, was reduced in size by rolling

Jan 1, 1969

The following is an incomplete list of members and guests who called at Institute headquarters during the period Nov. 10, 1918 to Dec. 10, 1918. Arthur C. Adair, Camp Meade, Md. L. S. Mitchell, Montreal, Canada. Arthur K. Adams, Camp Humphreys, Va. T. E. Mitchell, San Francisco, Cal. Toner Antisell, Chevy Chase, Md. H. Mortimer-Lamb, Montreal, Canada. V. W. Aubel, New Castle, Pa. Edmund Newton, A. C. Black, El Paso, Tex. Paul T. Norton, Jr., Columbus Ohio. 0. F. Brinton, Baxter Spgs., Kans. Elmer W. Pehrson, San José, Cal. C. S. Corbett, Minneapolis, Minn. Joseph E. Pogue, Washington, D. C. W. M. Corse, Mansfield, Ohio. T. C. Roberts, E. Orange, N. J. G. C. Crossley, Toms River, N. J. D. R. Semmes, Richmond, Va. H. S. Emlaw, Grand Haven, Mich. H. L. Slosson, Jr., San Francisco, Cal. Rudolph Emmel, Boston, Mass. W. H. Staver, S. G. Garrett, U. S. N. R. F. A. L. Sweetser, Boston, Mass. Lt. Francis Geib, Denver, Colo. Lt. H. B. Taylor, Kansas City, Mo. Wm. E. Hubbard, Wichita Falls, Tex. Kirby Thomas, New York. Arthur Iddings, Wichita Falls, Tex. Benj. F. Tibby, Salt Lake City, U. Zay Jeffries, Cleveland, Ohio. J. L. Towne, Whitepine, Colo. S. J. Kidder, Mogollon, N. M. Chas. W. Tubby, St. Paul, Minn. Lt.-Col. W. H. Lanagan (Engrs.). A. G. Waite, Brookline, Mass. Major W. F. Lewis (Engrs.). Timothy D. Walsh, Denver, Colo. 0. M. Lewyn, Thomas Warner, Phoenix, Ariz. A. McClintock, DeKalb June., N. Y. J. P. B. Webster, London, England. Major Donald G. Miller, N. M. E. W. Westervelt, Los Angeles, Cal. C. E. LeN. Arnold, formerly with the Inspiration Cons. Copper Co. at Inspiration, Ariz., has accepted a position with the Consolidated Arizona Smelting Co. at Mayer, Ariz.

Jan 1, 1919

By J. L. Gillson

Historically, rock deposits and sand deposits of titanium minerals came into production about the same time, although there may be some argument as to what is meant by production. Beach deposits of heavy minerals in India (Figs. 1-4) and Brazil (Figs. 5) were worked for monazite about the turn of century, but as there was then no market for titanium minerals, these were thrown away. The rock rutile deposits at Roseland, Va., Fig. 6, were worked to supply rutile for titanium chemicals and for coloring ceramics long before there was a titanium pigment business. The pigment industry started about the middle twenties, both in Europe and the U. S., and almost simultaneously the rock deposits at Ponte Vedra Beach near Jacksonville, Fla., were worked for titanium content. Since those days, production from both types of deposits has continued to grow at a rapid rate; many deposits of both types have been found, and reserves have grown to very large figures. In total tonnage of reserves, there is no doubt that the rock deposits are far ahead of the sand deposits; nevertheless there is a very large tonnage of commercial sands available. It is the quality of titanium mineral in the sand and the relatively lower costs of operating sand deposits that have kept them abreast, at least in annual tonnage produced, with the rock deposits. The principal titanium mineral used is ilmenite, but as soon as that mineral began to be sought as a titanium ore, it was obvious that there are ilmenites and ilmenites. Textbook ilmenite should have the composition FeOTiO2 and should analyze 52.6 pct TiO2 and 36.8 pct iron as Fe. The Indian ilmenite, for almost a generation the standard ore for manufacturing pigment in the U. S., was found to analyze about 60 pct TiO, and only 24 pct. Fe, and most of the iron is in the ferric condition. The whole process of pigment manufacture in the U. S. was built up on the use of a raw material of that grade, and the American chemical engineers who operate the pigment plants shuddered at the thought of using a rock ilmenite with 45 pct or so of TiO, and nearly 40 pct Fe. Intensive search was made around the world to find other deposits of rich black sand, like the Indian beaches, but although a few were found, there was some objectionable feature about each. A deposit in Senegal, south of Dakar (Fig. 7), was worked for a while, but an organic coating on the grains made attack by acid difficult. Modern practice would have included a scrubbing operation, in a caustic soda bath, to eliminate the organic coating. Brazilian deposits were numerous, but individually small, and shipping from them difficult. Deposits on the east coast of Ceylon had many attractive features, but the ilmenite analyzed only 54 pct TiO2 and could have been used only with a penalty. Sand deposits with 2 pct ilmenite, like those now worked in Florida, would not have been considered commercial ore, even if they had been known at that time. Most rock ilmenites are associated or mixed with hematite or magnetite, which accounts for the lower titanium and higher iron values than in the sand ilmenites. The Norwegians, English, and Germans, with cheap Norwegian rock ore at hand, learned to install in their pigment plants adequate capacity on the black side, as it is calltd, and counterbalanced the extra cost of plant, and larger amount of acid used, by the lower cost of ore. When World War II arrived, two of the largest pigment manufacturers in the U. S. had to learn how to use the Adirondack ilmenite, but one of them very gladly went back to sand ores when the Florida deposits came into large-scale production after the war. The other continues to use Adirondack ilmenite and finds it commercially attractive to do so. Rutile is not a raw material for titanium pigment manufacture by the sulfate process, since it is insoluble in sulfuric acid. In addition to its small consumption in chemicals and ceramics it began to be used in quantity in welding rod coatings. With the outbreak of World War 11, and the tremendous need for welding rods in shipbuilding and other structural steel construction, rutile suddenly became in heavy demand. The sand deposits on the eastern shore of Australia (Fig. 8A) which had been worked in a small way since 1934 were brought into production, and some stream placers in Brazil were worked and rutile concentrates shipped to American

Jan 1, 1960

By Paul M. Tyler

YEAR after year, the kaolin industry of the United States has been setting new production records and making better products. High-grade paper, pottery, and rubber clays are produced in this country mostly in the South. Georgia alone contributes over 70 pct and South Carolina almost 20 pct of the total domestic output. Residual kaolin is mined in North Carolina, highly plastic but naturally sandy Tertiary (Eocene) potting clays are worked in north central Florida, and good white clays are produced in several other states, but the main sources of kaolin or china clay have been numerous deposits in the Tuscaloosa (Upper Cretaceous) formation. This formation of generally sandy sediments is called the Middendorf member in older geologic reports and corresponds in age with some of the New Jersey clays. As shown in fig. 1, it crops out almost continuously in a generally southwesterly direction across South Carolina and Georgia and into Alabama. Clay is mined from this formation in all three states but the principal producing centers lie within about 10 miles of a straight line drawn between Aiken, S. C., and a point about 10 miles south of Macon, Ga. The white kaolins of the South were recognized and used prior to the Civil War but suitable treatment processes were not introduced until World War I when imports, chiefly from England, were curtailed. Although imports of high-grade clays were resumed after 1918, the domestic industry managed to treble its prewar production record during the early 1920's and has continued to grow. Whereas the 1909 to 1913 average total production in the United States was only 132,104 short tons valued at $705,352 f.o.b. mines, the output in 1948 was 1,568,848 tons worth $19,756,738.

Jan 6, 1950

By D. J. McAdam

Results of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station, Annapolis, Md., have been discussed by the writer in several recent paper~.1,2,3,4 In those papers references were also given to the work of Haigh in 1917.= Efforts by the writer to obtain a better understanding of some of the factors involved in corrosion-fatigue finally developed into a general investigation of the effect of time and cyclic stress on corrosion of metals. Corrosion-fatigue of Metals As described in the papers mentioned, rotating-cantilever specimens, conically tapered so that the stress is nearly uniform over a length of about 1.5 in., were subjected to simultaneous fatigue and corrosion. For this purpose a stream of water was diagonally applied so as to sweep the specimen from the outer to the inner fillet and surround the stressed surface with water. The fresh water is a calcium carbonate water, the composition of which has been given in a previous paper.2 The salt water is Severn River water having a saline content about one-third that of sea water. The previous papers described results obtained with ferrous and non-ferrous metals. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at nominal stresses far

By Joseph W. Richards

The Ashio copper-mine of the Furukawa Mining Co. is situated 18 miles from Nikko, and 109 miles north of Tokyo, near the center of Japan. The mine-waters are run over scrap-iron, whereby most of the copper is precipitated as cement-copper, leaving iron sulphate with some copper sulphate in solution. After using in the wet concentrating ore-dressing plant, the waste water contains clay and ore-slimes. The only avenue of disposal of this water is the Watarese river; but as this flows through valleys in which the water is used for irrigating the rice-crops, it is necessary to purify and clarify the water before discharge. The water amounts to from 600 to 700 cu. ft. (from 17 to 20 cu. m.) per minute, and averages about 0.00028 per cent. of copper, representing more than 18 tolls of copper per month. The water carries H2SO4, FeSO4, Fe2(SO4)3, CuSO, and other metallic sulphates in solution, and clay, ore-fines, slimes and basic iron sulphates as suspended matters. To purify and clarify the water, precipitation by milk of lime has been used, in three different ways, as follows: I. First Method, Copper not Recovered. Milk of lime was run into the water, and the mixture run through six settling-ponds, and then through a sand filter into

Jan 1, 1913

By James W. Neill

The occurrence of minerals of nickel and cobalt at Mine La Motte is probably known to every mineralogist. I will not attempt to describe these minerals, but, before entering on my subject, will briefly mention the ores, etc., which call for metallurgical treatment and enter into the composition of our mattes. Our staple lead-ore, the dressed galena, is the chief source of nickel and cobalt. It carries but a small percentage of these metals, viz.: 0.2 to 0.3 percent. usually, though when much copper pyrites is contained in the gangue, the amount of nickel and cobalt may be as great as 1.0 to 1.5 per cent. Next in importance is the ((middle product" of the dressingworks, consisting of the sulphides of iron (and copper) with gangue and galena. This usually carries 20 to 23 per cent. of lead, 0.5 to 1.0 per cent. of copper and 2.5 to 3.5 per cent. of nickel and cobalt. A larger percentage of copper always carries with it an increase of nickel and cobalt. In some few cases 12 to 15 per cent. of copper gives 6.5 to 8.0 per cent of these metals. Resides these products of the dressing-works, there is a small quantity of true nickel-cobalt-ore

Jan 1, 1885

By Geo. W. Goetz

The following tables show the analyses of ores from nearly all of the mines which will produce over 10,000 tons of ore each during the season of 1890. There are many small mines now in the course of development, some of which may become large producers. Many of the mines produce several different grades of ore, but the analyses given in the tables are fair averages of ore such as the respective mines can deliver. Most of these analyses were obtained from the agents of the respective ores, and are averages of the season of 1889. One can state positively that over 75 per cent. of all the iron-ores of the Lake Superior district will average over 60 per cent. of metallic iron. During the past 34 years this region has produced about 48,137,421 tons of ore, the different districts contributing about as follows: Marquette District,. 29,754,057 Menominee " .10,415,859 Gogebic " . 6,622,194 Vermilion " . 2,342,991 Miscellaneous,. .. .. 2,320 In the year 1889, the product of all the districts was nearly '1,300,000 tons. The product of the entire region for the season of 1890 may exceed 9,000,000 tons. This large amount of ore is shipped to the lower lake ports, from Escanaba, Marquette, Two Harbors and Gladstone.

Jan 1, 1891

By N. A. MacLeod

Ball wear in wet grinding mills has been the subject of considerable discussion in the last few years. Its importance to millmen is obvious in view of the fact that ball wear may cost from 2 to 4 per ton of ore for the more fortunate operators and many times this cost when a refractory ore must be reduced to a fine state of comminution. Consequently, any factual information that may be obtained on the nature of ball wear may be applied to introduce changes leading to lower ball consumption and therefore also to lower costs. In 1940, while employed with the Britannia Mining and Smelting Co., Britannia Beach, B.C., I had occasion to investigate factors that might affect ball consumption. We performed a number of tests, which will be briefly described. These tests originated as a result of changing from a 3½-in. ball to a 2-in. ball of different type of manufacture and were motivated by the desire to obtain the best possible type of 2-in. ball. Our testing was helped by the fact that the company operated a one-ton electric furnace, so that it was quite easy to make steel changes. It should be emphasized at the beginning that these tests produced results that in their general application to milling should be interpreted qualitatively rather than quantitatively. As will be evident in the description of the method used in testing, the balls were subjected to an intermittent batch grinding treatment, which may have produced results in rate of steel wear that may not have an accurate correlation with steel consumption in full scale mill operation. However, with this bed and rather arbitrary method of testing, results were obtained that may be of some interest and may stimulate further work on this subject. Unfortunately, owing to pressure of war work, our tests, which we had intended to repeat on a continuous grinding operation, had to be discontinued. Method of Testing Tests Were made in a Small cylindrical mill, rotating at 72 r.P.m. Internal dimensions of the mill were 10½-in. dia. by 9 in. The cylindrical inner surface was lined with rubber and the two ends were formed by steel plates. A charge of 2000 grams dry feed and 2000 C.C. of water was added evev 2 hr., the mill being drained of pulp before the addition of each charge, by tilting and sluicing with water. The mill was run On afternoon and night shift for daily periods of about 15 hr. total grinding time, and each test lasted from 60 to 150 hr. This batch method of testing involved a higher average pulp temperature in the mill, which undoubtedly affected comparative results in Some of the tests. Hardness oF Ball vs. Wear In these tests, special "eutectoid" steel balls were used, some of which were chill-Cut and quenched, some sand-cast and quenched, and some sand-cast and annealed to a dead soft condition. The results obtained, using as mill feed an ore containing considerable free quartz and

Jan 1, 1947

By N. A. MacLeod

Ball wear in wet grinding mills has been the subject of considerable discussion in the last few years. Its importance to millmen is obvious in view of the fact that ball wear may cost from 2 to 4 per ton of ore for the more fortunate operators and many times this cost when a refractory ore must be reduced to a fine state of comminution. Consequently, any factual information that may be obtained on the nature of ball wear may be applied to introduce changes leading to lower ball consumption and therefore also to lower costs. In 1940, while employed with the Britannia Mining and Smelting Co., Britannia Beach, B.C., I had occasion to investigate factors that might affect ball consumption. We performed a number of tests, which will be briefly described. These tests originated as a result of changing from a 3½-in. ball to a 2-in. ball of different type of manufacture and were motivated by the desire to obtain the best possible type of 2-in. ball. Our testing was helped by the fact that the company operated a one-ton electric furnace, so that it was quite easy to make steel changes. It should be emphasized at the beginning that these tests produced results that in their general application to milling should be interpreted qualitatively rather than quantitatively. As will be evident in the description of the method used in testing, the balls were subjected to an intermittent batch grinding treatment, which may have produced results in rate of steel wear that may not have an accurate correlation with steel consumption in full scale mill operation. However, with this bed and rather arbitrary method of testing, results were obtained that may be of some interest and may stimulate further work on this subject. Unfortunately, owing to pressure of war work, our tests, which we had intended to repeat on a continuous grinding operation, had to be discontinued. Method of Testing Tests Were made in a Small cylindrical mill, rotating at 72 r.P.m. Internal dimensions of the mill were 10½-in. dia. by 9 in. The cylindrical inner surface was lined with rubber and the two ends were formed by steel plates. A charge of 2000 grams dry feed and 2000 C.C. of water was added evev 2 hr., the mill being drained of pulp before the addition of each charge, by tilting and sluicing with water. The mill was run On afternoon and night shift for daily periods of about 15 hr. total grinding time, and each test lasted from 60 to 150 hr. This batch method of testing involved a higher average pulp temperature in the mill, which undoubtedly affected comparative results in Some of the tests. Hardness oF Ball vs. Wear In these tests, special "eutectoid" steel balls were used, some of which were chill-Cut and quenched, some sand-cast and quenched, and some sand-cast and annealed to a dead soft condition. The results obtained, using as mill feed an ore containing considerable free quartz and

Jan 1, 1947

By C. E. Westley, R. R. Beebe

Recent works by Plaksh et al.,1,2 Glembotsky,3 and others have renewed interest in the effects of oxidation on the surface activity of the sulfides. Since considerable supporting data are available on galena-potassium ethyl xanthate, this system is being studied at South Dakota School of Mines and Technology by contact angle measurement, using the technique of McGlashan and McLeod.4 The contact-angle method is well adapted to investigation of the influence of small amounts of oxygen on the establishment of a stable contact angle on galena in potassium ethyl xanthate solution. Samples of massive galena containing less than 0.001 pct Cu, 0.001 pct Ag, and 0.01 pct Zn are mounted in castable plastic and ground and polished manually in a glove box containing the desired proportions of oxygen and purified nitrogen. Oxygen and nitrogen contents of the test atmosphere are determined with an Orsatt analyzer. In this way a reproducible surface is created in contact with whatever oxygen concentration is desired. Water and all reagents are prepared and stored in the test atmosphere. An absorbent is used to control carbon dioxide that might be present. Final polishing is done with levigated alumina on a glass plate. The prepared sample is placed in the test solution and transferred to the contact angle apparatus in a sealed box, and the test is conducted while both sample and solution are maintained under a slight positive pressure of the test atmosphere. Table I gives the results of contact angle measurements made at various 02-Nz concentrations.5 Each value of contact angle is the average of at least six individual measurements made with different bubbles at different locations on the sample surface. A period of 20 to 25 min has been found by preliminary tests to be sufficient to permit develop- ment of maximum angle, and all measurements are made after at least this much time has elapsed. Exposure of prepared samples to pure water under the test atmosphere before exposure to the xanthate results in a small but measureable and consistent reduction in contact angle. This is particularly true in the oxygen-deficient atmospheres; for example, at 2.2 pct O2 such water contact reduces the average angle about 8" from that obtained by immediate testing in xanthate. The general trend of increasing contact angle with increasing oxygen concentration corresponds to the results of Plaksin et a12 The absence of diminish-ment of contact angle at very high oxygen concentration has been attributed to the high concentration of xanthate per unit of galena surface: At oxygen concentrations below 1 pct (the limit of accuracy of the Orsatt analyzer), no contact angle is obtained. Furthermore, no contact angle is obtained at any oxygen concentration in the absence of xanthate. This result seems to be in disagreement with those cited by Plaksin.1 Further work on the interaction of galena and potassium ethyl xanthate or a similar collector as influenced by oxygen is contemplated. The true nature of the interrelation is as yet unknown. For example, it is not known whether the governing oxygen reaction is with the mineral, with the reagent, or with both.

Jan 1, 1961

By D. C. Jillson

BRIDGMAN1,2 melted metals in a graphite or hard glass tube and lowered the tube through a furnace to make it cool from one end only. Because of the difficulty of eliminating all vibration of the mold, others have raised the furnace instead. Neither way seems as desirable as a setup with no motion of either the mold or the furnace. A furnace in which both the shape and the slope of the temperature gradient could be controlled and varied over a wide range and in which such a gradient could be moved from one end of the furnace to the other, freezing the specimen from one end to the other, at any desired rate, all by means of isolated external control, seemed to offer definite advantages. In addition to eliminating the possibility of vibration due to moving parts, it might also give better control over the direction and rate of heat flow. Such an apparatus was assembled and is shown schematically in fig. 1. Equipment Furnace: A clay-carborundum tube of 3 1/2 in. ID with a % in. wall thickness was used as the core. This had a main winding of No. 12 B.&S. gauge Nichrome V with some compensation for heat loss at the ends. Taps to this winding were made at points 12 in. from each end. Fig. 2 shows details of this winding and of the two end windings. Each end winding was wound over Micanite over the main winding. No. 15 B.&S. gauge Nichrome V was used for these, and again taps were supplied at two inter-mediat,e points on each. The tube was supported in an 18 in. OD black iron shell with brick insulation. The input to each of the windings was regulated by means of a variable transformer. Temperature Regulation: A chromel-alumel thermocouple located near the furnace wall in the center of the furnace was connected with a Celec-tray controller, type PIC, 300" to 900°C range, which opened and closed a shunt across an external variable resistance in the main winding circuit. An "anticipatory response" device also was incorporated to minimize the cyclic effect of the control mechanism. Eleven survey couples in a common pyrex glass protection tube were located near the furnace wall and spaced 2 in. apart. The couple leads went to a common reference junction box where they were connected to copper leads from a selector switch which, in turn, was connected to a type K potentio-meter. This arrangement permitted rapid temperature surveys. The knob on the controller dial was replaced with a threaded brass spool turned at a controlled rate by a thin iron wire one end of which was attached to a gear train and the other to a small weight heavy enough to prevent slipping of the wire on the spool. The gear train, driven by a 1-rpm Telechron motor, contained a series of different sized interchangeable gears and threaded drums permitting a range of travel speeds from 0.10 in. per hr up to a hypo-

Jan 1, 1951

By Whitman E. Brown, Louis J. Erck

L. A. ROE*—This paper is one of great value to the iron ore industry. The Humphreys spiral is a relatively new tool and gives promise of being quite useful in solving certain problems of iron ore beneficiation. Spirals have been tested on a martite ore at the Benson mine of Jones and Laughlin Steel Corp. in northern New York State. Our New York ore is considerably different, physically and mineralogically, than the one mentioned in this paper, and contains only 25 pct iron. This ore can be processed on spirals to give a concentrate containing 62 pct iron with an 85 pct recovery. On our particular ore we found operating difficulties when the spiral feed was coarser than 14 mesh. These were chiefly due to excessive "build-up" of locked middlings in the spiral circuit. In extreme cases these middling particles would accumulate to such an extent that the plant had to be shut down and the spiral surge tanks cleaned out. It is interesting to note that there exists a close relationship between the results of tabling a given iron ore and concentration of this same ore on Humphreys spirals. The size range of the ore must, of course, be within those limits acceptable to spiral concentration. Comparative tests on several of our mar-tite ores showed tabling results to be the same as spiral results. The authors make no mention of the use of a tailing stream splitter (now available from the spiral manufacturer) which is a useful tool in studying iron losses in the tailings stream. 011 our particular martite ore we found a considerable accumulation of fine-sized iron ore particles in the outside portion of the tailings stream. This fraction may be amenable to further treatment. E. H. ROSE*—The authors have concluded an interesting piece of work and this paper is an excellent factual account of a rapid and somewhat unusual transi-;ion in practice in the plant described. Perhaps it was modesty on their part which caused them so casually to limit to one sentence the fact that "several other methods of concentration on the fine ores representative of the Hill Trumbull group . . . failed to produce consistently an acceptable grade and recovery of finished product." The fact is that they were confronted by a difficult mineral-dressing problem and they are to be congratulated on their courage and persistence in staying with it until a satisfactory solution was evolved. A visitor to the plant might have been mildly astonished, as I was, to see one type of concentrator handling that part of the load early in the 1947 season, its experimental replacement by another a little later, and then in 1948 to see that both types had simply disappeared and their place taken by the spirals which were operating as placidly as though they had been there all the time. In working out economic methods of beneficiating Alabama red ore, most of which development is still ahead of us, it is likely that we also will pass through a period of successive disappointments, for we too have a problem where it is next to impossible either to "guess 'end right in the first place," or, because full-scale operating cost is such an important factor, to lay the ultimate answer on the line in advance by means of laboratory experimentation. Iron ore being what it is instead of what it used to be, it is encouraging to have the example the authors have given us today that a tough nut that will not crack on the first blow or the second is apt to do so on the third or fourth.

Jan 1, 1950

By Stanley L. Lopata, Eric B. Kula

The problem of preferred orientation has been considered in quantitative phase analysis by X-ray diffraction techniques. The average intensity of a diffraction peak can be obtained by integration over the whole pole figure, or by random rotation of the specimen in the X-ray beam, or by a combination of both. For rod or wire, where the pole figure shows rotational symmetry, the intensity is measured along a radius of the pole figure. Where no symmetry is present, rotational symmetry is imparted by rapid rotation of the sheet around its surface normal during measurement. These methods are applied to the determination of aus-tenite in an Fe-31 pct Ni rod and Fe-28 pct Ni sheet. X-RAY diffraction techniques are frequently used for quantitatively determining the relative amounts of two or more phases present in a structure.1,2 Briefly, the method requires a measurement of the intensity of a Bragg reflection for each phase. The method is based on the principle that the intensity of a Bragg reflection, IA, is directly proportional to the volume fraction of the given phase present, CA: T KRACA/2µ [1] where K is a constant independent of the diffracting phase, RA can be calculated and depends on the Bragg angle ? and the particular reflection measured, and µ is the linear absorption coefficient of the mixture.' For a mixture of two phases A and B, IA = RAcA [2] IA/IB=RAcA/Rbcb and CA+ CB = 1 [3] This allows the volume fraction of a phase to be calculated directly from the measured integrated intensities of the two phases present. This method is frequently used for quantitatively determining retained austenite in steels, but can be used for the quantitative determination of in titanium alloys, as well as phases in other alloy systems. The intensities are generally measured by diffracting only from planes whose normals are perpendicular to the specimen surface, with the implicit assumption being made that this intensity is typical of reflections from planes whose normals lie at other angles to the surface. If the specimen contains a texture or preferred orientation of the crys- tallographic planes by virtue of previous mechanical working, however, this measured intensity is correct only if the intensity level fortuitously is one times random. Examination of pole figures for actual rolled sheet shows that the intensity level at the center of the figure is seldom at the random level, and can very easily differ by a factor of five or more, leading to a commensurate error in the calculated amount of the phases. Textures have been commonly found in materials which are cold-rolled or recrystallized after cold rolling. This problem is becoming of greater importance since structural materials in use today, such as the high-strength stainless steels, frequently are further strengthened by cold rolling, and hence contain textures. Although high-strength carbon-containing alloy steels generally do not contain textures, some of the newer thermomechani-cal treatments will impart a texture even in these cases. In the case of hexagonal metals, such as titanium, probably every wrought sample will show some anisotropy. Since the standard X-ray techniques are inapplicable in all these cases, there is a clear need for some method of taking this anisotropy into account. The specific problem is to obtain the integrated intensity of a Bragg reflection for each phase, averaged over all orientations of the sample with respect to the X-ray beam. This can be done either by purely mechanical means or by a mathematical averaging. Mechanically, a small spherical speci-

Jan 1, 1965

By S. L. Couling, D. J-P. Adenis

i2) twinning in poly crystalline magnesium does not usually occur homogeneously but is concentrated in localized regions or bands inclined at about 45 deg to the stress axis. These bands of twinning are in many ways similar to the Luders bands seen in mild steel alzd Al-Mg alloys. Within a hand the percentage of the volume twinned may approach 100 with no twinning outside the band. Bands are not produced in specimens of grain size a3 x 10-= in. or in samples deformed at temperatures 300°F. Annealing of heavily twinned regions leads to re crystallization textures markedly different from those found in the starting material. The exact preferred orientation appears to depend on the starting grain size, the amount of compres-sive strain and the manner in which it is introduced. MAGNESIUM, with its hexagonal crystal structure, deforms plastically at room temperature by a variety of deformation mechanisms, one of the most important of which is (1012) twinning. In single crystals such twinning occurs on compression parallel to the basal plane or tension perpendicular to it. In wrought polycrystalline magnesium, such as rolled sheet, the preferred orientation is such that almost all the grains have their basal planes nearly parallel to the sheet surface. Therefore, if sheet material is deformed by cold rolling or by tension in the plane of the sheet, deformation of the grains by (1012) twinning is not favored. On the other hand, twins form readily on compression parallel to the plane of the sheet as in a compression test, on the compression side of a bent sample, or at the outer rim of a drawn cup. The first part of this paper deals with the morphology of (1012) twinning in polycrystalline magnesium. Some aspects of this subject were covered by Barrett and ~aller.' Of direct bearing on the work to be reported here are the comments of Jetter' in discussion to Ref. 1. He shows that Mg + 1.5 pct Mn alloy sheet when bent about a transverse axis develops a pattern of transverse bands on the surface of compression. A longitudinal section through the sheet shows that the bands are wedge-shaped and inclined to the rolling direction. The bands were identified as "outcrops of regions in which deformation is localized as the result of the reorientation brought about by (1012) twinning". The second part of the paper treats the recrys-tallization texture of the specimens twinned by compression. Magnesium deformed and then annealed generally recrystallizes with no change in orientation.1'3'4 This statement is true provided that the amount of (1012) twinning occurring during deformation is small. In an isolated observation, Anse15 has shown that, when deformation produces much (1072) twinning, annealing causes new maxima to appear in the pole figure. The second part of the paper elaborates on this point. I) MATERIALS AND PROCEDURES All of the experimental work to be reported was done using the commercial sheet and plate alloy AZ31B (nominal composition: 3 pct Al, 1 pct Zn, 0.4 pct Mn, balance magnesium). This alloy is available commercially in two tempers, -0 (fully annealed) and -H24 (partially annealed), and specimens of both tempers were used in various experiments. The average grain. diameter (AGD) for -0 temper 0.125-in. sheet is about 0.5 x 10- in.; where material of larger grain size was desired, anneals at elevated temperature were used to grow the grains. compression tests were made on a screw-driven "hard" machine. The specimens were clamped in a

Jan 1, 1964

By J. Lemish

Considerable research has been conducted in Iowa in recent years on carbonate aggregate reactions in concrete. Groups outside the state have become active in the past few years after recognizing that certain carbonate aggregates are reactive in concrete. The paper reviews the nature and extent of the problem and a summary is given of research by the author and his associates. In recent years considerable research has been conducted in Iowa on carbonate aggregate reactions in concrete. The research is part of a general study on the behavior of carbonate rocks as concrete aggregates sponsored by the Iowa State Highway Commission. Research on carbonate aggregates has not been extensive in the past. Laughlin1 published one of the first papers on carbonate aggregates in 1928 and was followed by others, notably H. S. sweet,' B. Mather et al.,3 and K. Mather4 who emphasized the petrographic and physical aspects of carbonate aggregates. The recognition that certain carbonate aggregates are reactive in concrete has led to increased participation in research in the past few years by groups outside of Iowa. Significant contributions have been made by Swenson and Gillot,5 Hadley,6 and Chaiken and Halstead7 in work which emphasizes the expansion of carbonate rocks in alkaline environments and the reaction of carbonate minerals or dedolomitization with alkalies. It is the purpose of this paper to review briefly the nature and extent of the problem and present a summary of the research by the author and his associates. EXTENT AND NATURE OF THE PROBLEM The problem is the deleterious behavior of certain carbonate aggregates in concrete. It was first recognized in Iowa over 20 years ago when poor service records of certain highways were correlated with aggregates produced from the Glory and LeGrand quarries. Deleterious behavior of carbonate aggregates have been reported in Canada and, more recently, in New York and Virginia. As more knowledge is gained concerning the problem, distress in concrete related to carbonate aggregates may be recognized over a widespread area. The problem may potentially exist in the Midwest, the Northeast, and other parts of the country underlain by thick sections of carbonate rocks readily available for utilization as aggregates. The nature of distress in Iowa highways is a general weakening and deterioration of concrete characterized by progressive cracking and spalling away from joints and edges (Fig. 1). The distress generally occurs after 15 years of service and becomes progressively worse. Specimens of such concrete lack the toughness of sound concrete and break easily under the hammer in the manner of a soft brick. The matrix is generally highly carbonated and dark borders, or reaction shells or rims outline the argillaceous carbonate aggregate fragments (Fig. 2). Cracks observed in cores cut across the aggregates and concrete matrix. Although localized volume change (expansion) is associated with spalling, there is no definite field evidence in Iowa that excessive growth of concrete slabs has occurred. The experience with carbonate aggregates in Iowa indicates that the concrete deterioration is not the same as that induced by the alkali-aggregate reaction associated with siliceous aggregates. The principal difference is that in Iowa the distressed concrete is weakened throughout the slab. In concrete affected by the alkali aggregate reaction, the

Jan 1, 1961

By B. H. Kear, H. G. F. Wilsdorf

After a few percent strain, dislocations in disordered Cu3Au are arranged in groups in ulell-defined slip planes, which contrasts with the more or less random distribution of dislocations in the corresponding ordered alloy. Unusually long and straigkt dislocation segments observed in the ordered alloy are interpreted in terms of cross slip of screw dislocations from their slip planes into cube planes. It is proposed that cross slip, and also dislocation reactions of the Lomer type, play an important role in work hardening of the ordered alloy. ACCORDING to to dislocations in the disordered lattice are only partial dislocations in the corresponding super lattice, so that in the super-lattice dislocations must occur as pairs, with each pair connected by a ribbon of antiphase boundary. Recently, striking confirmation of the theory was obtained by Marcinkowski, Brown, and Fisher3j4 in a study of dislocation configurations in thin foils of the Cu3Au alloy by transmission electron microscopy. In the present investigation, the observations made by these workers have largely been confirmed. Moreover, it has been found that dislocations in the plastically deformed ordered alloys are often unusually long and straight. This paper is mainly concerned with these new observations. A tentative explanation is offered in terms of cross slip of dislocations in the ordered alloys. PREPARATION OF SPECIMENS An alloy close to the stoichiometric composition Cu3Au was prepared by melting together high-purity copper and gold (99.995 pct) under vacuum in a graphite mold. The resulting ingot was rolled down and cut into strips 1 1/2 by 1/8 by 0.005 in. in thickness. All strips were annealed at 900°C for 3 hr and cooled to 500'~. A few of the strips were quenched from ~OO'C, while the remainder were slowly cooled in the temperature range 400" to 150°C at intervals of a few degrees every 24 hr to produce a high degree of order. After this annealing treatment the average grain size of the material was about 0.1 mm. Material in different states of order was obtained by reannealing fully ordered material at temperatures below the critical temperature: followed by quenching. The equilibrium degree of order attained at a particular reannealing temperature was obtained from the paper by Keating and warren.' A simple hand-operated tensile jig was used to give the strips the required amounts of plastic strain. Following straining, a number of specimens were cut from each strip by means of an electrolytic cutting device.= Finally, each specimen was thinned electrolytically using the polishing procedure described by Bakish and Robertson,7 and these thin sections were examined in the Philips EM-100B electron microscope operating at 100 kv. EXPERIMENTAL OBSERVATIONS Antiphase boundaries. The average domain size in the ordered alloys was found by direct observation to be about 0.25 p. Also, it was observed that the grown-in configuration of antiphase boundaries was changed little by plastic deformation, at least up to 6 pct strain. Fig. 1 shows an electron micrograph of a thin foil of partially ordered alloy (S - 0.8) after 3 pct strain. The micrograph shows a few dislocation pairs and a somewhat crystallo-graphic network of antiphase boundaries. The normal to this foil was found by diffraction analysis to be approximately 11121, with principal directions in

Jan 1, 1962

By Joseph J. Becker

RECENTLY the "oriented growth" hypothesis of recrystallization textures has been receiving considerable attention. According to this view, "whenever a new generation of grains is growing in a highly oriented matrix . . . one may assume . . . that from among available nuclei of a great variety of orientations those with suitable orientation relationship with respect to the matrix have by far the highest rate of growth (oriented growth) and will, therefore, predominate."' This statement includes primary recrystallization of single crystals and of polycrystalline materials showing strong deformation textures as particular cases. While the phenomenon of oriented growth undoubtedly does operate, and may be of importance in coarsening or secondary recrystallization, the writer feels that its extension to primary recrystallization is a different matter. Several aspects of this phenomenon may be pointed out which are difficult to rationalize on the basis of oriented growth. In recrystallizing deformed single crystals of alpha brass, Maddin, Mathewson, and Hibbard2 found that the twin composition planes of the recrystallized grains were parallel to the three operative slip planes they observed, and not to the fourth octahedral plane. The writer's current work seems to indicate further that when only one or two slip systems can be seen to operate, the recrystallized grains are aligned only with those slip planes actually observed. This behavior could hardly be accounted for by oriented growth, because on the latter basis the recrystallized texture of a deformed single crystal should certainly have the same symmetry as the crystal itself. Growth rates could not be expected to distinguish between crystallogra- phically equivalent directions, unless the presence of a visible slip system vastly increases the growth rate in the appropriate direction. This seems unlikely. These relationships were observed by the writer only when considerable care had been exercised before annealing to etch away the effects of cutting out the centers of tensile specimens with a jeweler's saw and to etch off the ends of compression specimens. When these.precautions were not taken, nu-cleation inevitably appeared to occur at the saw cuts or at the ends, and the resulting orientations never showed a [111] rotation but appeared quite random. The provision of many nuclei of many orientations did not enhance the correlation, but destroyed it. Recrystallization textures are sometimes strongly dependent on annealing temperature, which would imply that the anisotropy of growth rates is a suddenly varying function of temperature. This might be regarded as unlikely. Recrystallization textures can be strongly dependent on the degree of deformation. If textures are to be explained by selective growth from among nuclei of all orientations, it is difficult to see how the recrystallization process could have any dependence whatever on the manner or degree of deformation. It is felt that the above points should be considered before the oriented growth hypothesis is applied to primary recrystallization, with the necessary complete divorce of the mechanism of recrystallization from the details of the deformation process. References 1P. A. Beck and H. Hu: Reply to discussion of their paper on Recrystallization Texture and Coarsening Texture in High Purity Aluminum. Trans. AIME, 188, 1057; Journal oF Metals (Aug. 1950) TP 29083. 'R. Maddin, C. H. Mathewson, and W. R. Hibbard, Jr.: The Origin of Annealing Twins in Brass. Trans. AIME, 185, 655; Journal of Metals (Sept. 1949) TP 26763.

Jan 1, 1952

By Karl F. Peterson, H. K. Najarian, Robert E. Lund

R. E. Powers (Mellon Institute of Industrial Research, University of Pittsburgh, Pittsburgh)—Several of the processing methods at the Josephtown smelter might well be considered by plants producing iron blast furnace sinter. In making blast furnace sinter the objectives are much the same as at Josephtown: To produce a strong yet porous agglomerate which has a size consist in a preferred range. The emphasis however is on production rate rather than on the size or other quality characteristics of the sinter. Therefore the technique is entirely different. Blast furnace sinter plants attempt to make their product in one pass with a minimum recirculating load and without sizing treatment after the sinter leaves the machines. Many plants are beginning to feel that more attention paid to quality characteristics would make the product a more desirable blast furnace material. The pelletizing of very fine material before placing it on the bed is not deliberately done at iron sinter plants, although the installed equipment sometimes gives a simila; action. Such pelletizing seems to be a promising way of accommodating the down-draft sintering Drocess to very fine materials. he recirculating load at Josephtown is extremely high. Two plants' producing blast furnace sinter from raw material of comparable size have a recirculating load of about 100 pct of production. At Josephtown it is notable that the size and the rate of feeding of return fines are under control. This is not the case in most blast furnace sinter plants. The sinter slicer appears to be a worthwhile aid in effecting such control. It is similar in action to rakes and plows used at a number of plants, but it has the advantage that the sinter dislodged is positively removed and not left to the inefficient action of a stationary grizzly screen. Blast furnace size specifications for sinter are not at present so rigid as the Josephtown specifications. If the sizing of blast furnace sinter does become important, then the Josephtown crushing practice, in which a large recirculating load is maintained on the crusher in order that minimum fines be produced, may be of interest. H. K. Najarian (authors' reply)—We note that Mr. Powers appreciates some points that we tried to emphasize in our paper as being of importance in making zinc sinter of good quality and which may well be applied to iron blast furnace sinter. Fig. 2 shows the pelletized nature of the feed going on to a Dwight-Lloyd type sintering machine in our plant. Practically, the entire feed consists of more or less rounded particles which permit more uniform air passage through the charge, while the larger particles in the charge roll on to the surface of the grate, which helps to keep the grate openings from being clogged by excessive fines. An agglomerated charge of this character may preferably be made by rolling action while being mixed in a rotating drum and wetted by water sprays to bind the fine particles together and give the charge the desired moisture content. From our observations of several iron ore and blast furnace flue dust sintering operations, we believe that if the fines from the sinter discharged from the machines were to be recirculated and agqlomerated with the new feed, not only sinter of better quality but larger capacity from the machines may be realized.

Jan 1, 1952