Search Documents

By E. W. Johnson, M. L. Hill

Cold working of iron-carbon alloys was found to increase greatly the hydrogen solubility and to decrease the diffusivity at temperatures up to 400° C. These effects are increasing functions of both the carbon content and the degree of deformation. The hydrogen behavior is consistent with the idea that cotd working creates "traps", which are concluded to be microcracks in which the hydrogen is chemisorbed. Hydrogen embrittlement is explained by the Petch theory of metal crack surface energy loss due to hydrogen adsorption. HYDROGEN embrittlement of steel has been studied for many years and has been the subject of an extensive literature, but the mechanism of the effect has not been completely understood. The embrittlement is unusual in that the ductility loss is not accompanied by an increase of the yield strength, being primarily a decrease of the fracture strength alone. The loss of fracture strength is usually most severe in the temperature range between 0°and 100°C. Here the solubility of hydrogen in the iron lattice at ordinary H2 pressures is extremely low while the diffusivity is still quite high. From the relationships between the ductility and the hydrogen content, test temperature and strain rate, it is apparent that the hydrogen atoms causing the ductility loss difbse to and concentrate in small regions of the metal which are especially susceptible to the initiation and propagation of fracture. This hydrogen segregation apparently occurs after plastic straining has begun. Below 0°C the ductility loss persists only at low strain rates in confirmation of the view that the embrittlement is diffusion .controlled. The tendency of the embrittlement to disappear above 100°C can be explained by the increasing lattice solubility of hydrogen with rising temperature. A common view of hydrogen embrittlement of steel is that the hydrogen initially dissolved in the metal lattice diffuses to structural discontinuities and there precipitates as H2 gas at very high pressures which assist the external stress in causing premature failure.1,2 The idea of a high H2 pressure in equilibrium with ordinary amounts of hydrogen in steel at room temperature is due to observations of hydrogen behavior in fully annealed material, for which the Sieverts' law constant relating solute concentration to H2 pressure is extremely small. Hydrogen-embrittled steel, however, is always plastically deformed to some extent, and therefore it is important that hydrogen embrittlement be explained primarily in terms of hydrogen behavior in plastically deformed material. Such an explanation is attempted in this paper. Previous studies of hydrogen in cold-worked steel have shown that both the solubility and the diffusion rate are significantly chaned when the steel is cold worked. Darken and Smith discovered that the amount of hydrogen absorbed from acid by cold-rolled steel at 35°C is many times greater than that absorbed by hot-rolled steel. They found also that the hydrogen permeability of the steel is unaffected by cold working. Keeler and Davis4 confirmed the high apparent solubility of hydrogen in cold-worked iron-carbon alloys at temperatures up to and even beyond the recrystallization temperature. They also found that this solubility increase accompanying cold work is a sensitive function of the carbon content, being absent when no carbon is present. The present experimental study was undertaken primarily to obtain an improved understanding of the behavior of hydrogen in cold-worked steel. Data were obtained on the effects of temperature, H, pressure, carbon content, and degree of cold work on the hydrogen solubility and diffusivity in iron-carbon alloys. These data have been helpful in elucidating the nature of the cold-worked steel structure as well as in providing information on the mechanism of hydrogen embrittlement of steel. EXPERIMENTAL Cylindrical specimens for hydrogen absorption and diffusion rate measurements were prepared from three iron-carbon binary alloys and a commercial SAE 1010 steel. The iron-carbon alloys were prepared by vacuum melting electrolytic iron with graphite in a magnesia crucible. The alloys were cast in vacuum as 2 1/2-in. sq ingots weighing about 20 lb each. The ingots were hot rolled (above 1900°F) to 5/8-in.-diam round bars and then cooled in air to room temperature. The resulting metallographic structure consisted of islands of fine pearlite surrounded by free ferrite. Chemical analyses of the materials are given in Table I. The 5/8-in. diam bars were turned to diameters such that cold reduction to the desired final specimen diameters would result in either 30 or 60 pct reduction in area (RA). The machined bars were then cold worked by swaging at room temperature

Jan 1, 1960

By David D. Rabb

Leaching or solution mining, a relatively simple and economical process for beneficiating metallic ores, is likely to find increasing application in the treatment of low-grade ores that are impractical to mine by any other means. This process may be carried out in two different ways: 1) dump leaching, where the ore is moved from its original location to be leached at another site; and 2) In-situ leaching, where the ore is leached in place by introducing the leach solution at the top, letting it flow down through the ore under gravity, and then recovering it plus the dissolved metals it contains. Whichever leaching method is used, it is almost always necessary to break up the ore before leaching. In this paper a study is reported which indicates that rock broken by an explosion-in particular, an underground nuclear explosion-is significantly more amenable to leaching then is rock broken by other methods. These results suggest that the leaching speed and efficiency could be increased by nuclear fracturing of the ore. Not only would the leach time be shortened, but the resulting increase in strength or richness of the solutions would decrease plant installation expense as well as reduce pumping and processing costs. A considerable fund of experience has been accumulated in the course of several hundred experimental underground nuclear explosions, so that the gross results of any given nuclear explosion can now be predicted with a fair degree of confidence.' From this knowledge it seems clear that, under the proper conditions, large ore bodies can be fractured much more economically-macroscopically speaking-by nuclear explosions than by other methods. The present study concentrates on smaller scale effects that is, the cracks in the chunks of rock broken by the explosion-and shows that here too, in the microscopic domain, there are important advantages to nuclear fracturing. The intense shock produced by the very fast acting, high-brisance nuclear explosive fractures the rock in a way that should significantly improve its leachability. Experimental Procedure This study compared rocks broken by nuclear explosives with rocks produced by conventional mining, quarrying, or core drilling. The test samples, granite chunks 6 to 8 in. on a side, plus core sections, came from the area of the Hardhat*2 nuclear explosion and were taken both before and after the explosion. For comparison, several samples of quarried granite were obtained from a local gravestone monument company. The general procedure was to soak the test samples in leaching solution and then determine the extent of penetration. A standard commercial copper leaching solution was used (10 gpl Cu, 10 gpl H2SO4, 5 gpl ferric Fe, 15 gpl total Fe, pH about 1.5), to which a water-soluble penetrant dye, Zyglo 1-c, had been added. Details of the procedure were as follows: 1) Sample leached in solution containing Zyglo penetrant dye. 2) Washed with water. 3) Air-dried. 4) Cut with granite wire saw. 5) One face polished with granite monument polish. 6) Sent directly to be photographed, or heated at 110°C for 2 hr and then sent to be photographed. 7) Photographed under ultraviolet light to show crack patterns. Results After 10 days of leaching at 70-75°F, the samples were removed from the solution, washed, dried, and cut in half with a granite wire saw to study the penetration of the leach solution. Since the Zyglo dye in the leach is visible under ultraviolet light, the degree of penetration of the leach (and hence the cracks in the samples) can be studied on photographs of the crosscut samples made under ultraviolet light. The photos in [Fig. 1] show how the leach solution penetrated various representative samples. Of the 71 rock samples examined, fractures were most frequent and prominent in samples from the rubble produced by the nuclear explosion [(Fig. 1D)]. Fracturing was less apparent in shaft-mined rock [(Fig. 1B)], still less evident in drift-mined rock [(Fig. 1C)], and practically nonexistent in cored or quarried specimens [(Fig. 1A)]. The samples in [Fig. lA-C] were from the same general area as the nuclear explosion, but they were obtained before the explosion. Results of the crack studies are summarized in [Table 1]. The Zyglo-treated leach solution penetrated the test samples at the rate of about 1/2 mm during the first hour, 1 mm by the end of 4 hr, 2 to 3 mm in 12 hr, and 4 to 6 mm in 10 days, showing a progressively slower rate with time.

Jan 1, 1972

By M. D. Hassialis, C. G. Myer

THE nature of a collector-coated mineral surface has been the subject of some experimentation and much speculation. Various aspects of the problem have been isolated and studied; it is probable, however, that there exist aspects as yet unrecognized, which are needed for a complete description of the system. The recognized elements of the problem are: 1—The nature of the chemical units comprising the film and the nature of the forces holding these chemical units to the mineral surface; 2—The orientation of the chemical units at the surface; and 3—The disposition of the collector units at the mineral surface. This report touches upon all three aspects of the broad problem; it deals, however, with a new and heretofore unrecognized element—the mobility of the collector units in the two dimensions of the solid-liquid interface. Regardless of the viewpoint adopted as to whether the chemical units comprising the collector film are collector ions or molecules, held either by chemical or physical forces, the writers on flotation theory are in apparent agreement as to the orientation of the chemical units at the mineral surface. Wark and Cox' showed that the contact angle at a stable collector-coated surface in a constant chemical environment is independent of the nature of the mineral and of any resurfacing agent; it depends solely upon the collector used. They showed further that the value of the contact angle increases with the number of carbon atoms in a homologous series of compounds. Taggart, Taylor, and Knoll2 postulated that the collector ion is oriented with the chemically reactive, polar end toward the mineral surface and the non-polar, hydrocarbon-like end toward the liquid phase. In support thereof they cited the abstraction of p-p1 dihydroxydiphenylthiourea and of glycol xanthate8 by galena without a concomitant increase in the contact angle above that of clean galena. It was argued that in these cases the water-repellent layer which normally would be presented to the liquid phase owing to the orientation of the collector ions is overlain by a layer of water-avid groups, the hydroxyl groups. Implicit is the analogous orientation exhibited by a monomolecular layer of an insoluble substance at an air-water interface. It should be pointed out that these facts also are consistent with the concept that the collector units be flat on the surface of the mineral and that the response of the surface to an air bubble is determined by the ratio of the area covered by water-avid groups to the area covered by water-repellent groups; the areas being weighted according to the relative watef-avidity or water-repellency of the groups involved. The disposition of the chemical units of the collector film at the mineral surface has not received the attention it merits. Taggart4 concluded from the observed stoichiometry of the ions entering and leaving a surface that the stoichiometry is obeyed in detail at the surface of the mineral. Thus, in the case of xanthate-coated galena, pairs of xanthate ions are attached to surface lead ions. In the case of chemisorption, Gaudin and Preller postulated an agreement between the atoms or ions of the substratum (the mineral surface) with those of the superstratum (collector film); in the case of the physical adsorption their position is not clear. In one place they state "the first type (physical adsorption) does not require any agreement between the atoms or ions of the substratum with that of the superstratum" and in another place that "It seems, in fact, as though some slight influence of the substratum is formed even in physical adsorption." The present work shows that in some cases of chemisorption the chemical units of the collector film are in constant surface-bound motion and may not be assigned to any site of the surface, hence there is no permanent association between the chemical units of the film and the atoms or ions of the solid. The physical property of the collector film that is of paramount importance is its surface energy. Although this property is not susceptible to direct experimental determination, the related contact angle is. Much of the knowledge of the properties of a collector film derives (by deductive and inductive reasoning) from the behavior of an air bubble thereat

Jan 1, 1952

By M. S. Rashid, C. J. Altstetter

Allotropic transformations in cerium have been studied by dilatometric, resistometric, X-ray diffraction, and metallographic techniques. The dilatometric study indicated that, on cooling below O°C, the high-temperature fcc phase, y, transforms partly to the hexagonal phase, ß, and, on further cooling, to the collapsed fcc phase, a. The amount of $ phase present at room temperature is increased by repeated cycling through the a-y transformation. It has been shown metallograPhically that the y-ß transformation has many characteristics of a martensitic transformation. In contrast to the y-ß transformation the ?-a transformation does not give the manifestation of a shear transformation. Small cellular ? domains of random shape and size collapse to a in a short time with no apparent coordination with neighboring domains. The considerable confusion in the literature over the existence of more than one high-temperature fcc phase is discussed. Two such phases have been reported in the literature and an attempt is made in this study to clarify the situation. Twelve fcc and two hcp structures have been shown to be easily reproduced or eliminated. It is proposed that the two "additional" allotropes reported in the literature and fourteen of the phases detected here are not allotropes of cerium but are due to contamination. CERIUM exists in several allotropic forms, but there is some disagreement over what the forms are. Furthermore, the conditions favoring the presence of a particular allotrope and the nature of the transformations from one form to another are uncertain. The objectives of this research were 1) to ascertain the allotropic forms of cerium, 2) to establish the conditions under which the allotropes exist, 3) to study the effects of annealing and thermal cycling on the allotropic transformations, and 4) to study the transformation mechanisms. Dilatometric, resistometric, metallographic, and X-ray diffraction techniques were employed. The form of cerium commonly found at room temperature is fcc and is designated ?. A complex hexagonal phase, 8, forms when y is cooled to slightly below room temperature. At still lower temperatures the y fcc structure transforms to an fcc form with a much smaller lattice parameter, termed a cerium. A bcc form, 6, which exists just below the melting point (800°C), will not be considered further in this work. There is a substantial body of experimental evidence (reviewed by Gschneidnerl) which favors the acceptance of these four allotropes, though some investigators have tried unsuccessfully to observe the ß hexagonal form.'-' There is disagreement, however, over the phase-transformation temperatures, due, in part, to broad hysteresis and overlapping of the transformations between the a, ß, and ? forms. The transformations are also sensitive to prior thermal and mechanical treatment. The differing purity of cerium used by different investigators is undoubtedly a factor. Cerium is difficult to separate from other elements and is quite reactive, igniting spontaneously when it is filed in air. The highest purity of cerium to date is reported to contain several hundred parts per million by weight of impurities, and early investigations were carried out on cerium containing several percent of impurities. There have been reports of more than one fcc allotrope at room temperature. Gschneidner, Elliott, and McDonald5 obtained diffraction patterns of an fcc phase with a lattice parameter about 1 pct less than that of the ? phase, instead of the y phase, on slowly cooling cerium filings from 23° to -198°C and warming them back to room temperature. However, when the sample was heated to 447°C and cooled to room temperature it consisted of only the ? phase. They have designated this new fcc phase "a-? intermediate", and say it is quite sensitive to impurities. After prolonged high-temperature treatment of a powder specimen, Weiner and Raynor2 obtained a diffraction pattern of an fcc phase of lattice parameter about 1 pct less than the ? phase. This they called the y' phase. It could not be reconverted to the y phase and is claimed to be different from the a-? intermediate phase.5,6 Dialer and Rothe3 reported two fcc phases* after cycling their powder specimens between room temperature and -192°C. Gschneidner, Elliott, and McDonald5 suggested that one of the fcc structures obtained by Dialer and Rothe was equivalent to their "a-? intermediate" phase. Table I presents some pertinent data on the proposed allotropes. For the ?(fcc)-ß(hexagonal) transformation

Jan 1, 1967

By Charles R. Keyes

PAGE I. Introductory............ 140 II. Location and History...........140 III. Surface-Relief of the District....... 141 IV. General GeoloGic Features........ 142 1. Main Relationships and Map....... 142 2. Résumé of Geologic History..143 V. Geologic Formations Represented...144 1. Broader Considerations......... 144 2. Geologic Section.......... 145 3. Nomenclature.......... 146 4. El Pasan Limestones..146 5. Santa Rita Limestone.... 146 6. Silver Shales........... 147 7. Bella Shales........... 147 8. Berenda Limestone..147 9. Grande Limestone... 148 10. Lake Valley Limestone........ 148 11. Sierra Limestone.......... 149 VI. Unconformities........... 149 VII. Geologic Structure.......... 150 1. Main Characteristics......... 150 2. Folding........... 1.50 3. Faultings........... 150 4. Relations of the Eruptives...153 VIII. Geologic Relations OF the Ore-Bodies...... 154 1. Governing Factom......... 154 2. Position.......... 154 3. Relations to Foldings...155 4. Relations to Lines of Dislocation... 15.5 5. Relations to Present Surface.Relief..156 6. Relations to Eruptive Rocks...157 7. Relations to Lithologic Nature of the Rocks.... 158 IX. MINERALOGIC CHARACTER OF THE ORES...... 158 X. Origin of the Ore.Deposits..159 1. General Statement......... 159 2. Original Source of the 0re.Materials...160 3. Contact-Metamorphism of the Region... 161 4. Process of 0re.Concentration..162 5. Lowering of Ground-Water Level..162 6. Formation of Cerargyritic Ores...163 XI. Recapitulation........... 168

Jan 1, 1909

By J. E. Nesset, J. A. Finch

A model of the fully-loaded condition of particle accumulation on the matrix of a high gradient magnetic separator is developed. The model accurately predicts the build-up profiles reported recently by Friedlaender et al. A powerful development from the model is that loading (volume of accumulated material per unit volume of matrix) is uniquely defined by a dimensionless group, called the loading number, NL. From direct measurements, NL proved superior to the dimensionless group proposed by Watson as a measure of loading. The fine size limit of hematite recovery is examined using NL.

Jan 1, 1980

By A. N. Diehl

IT is the object of this paper (1) to deal with the elements in blast-furnace gas from the standpoint of their importance, and the part they are to play in future consumption, and (2) to give detailed information about the construction and operation of a plant designed among the first in this country for washing gas on a large scale.

Jan 5, 1914

By H. C. Fiedler

It was recently shown with 3.3 pct Si-Fe containing 0.026 pct S and 0.06 pct Mn that the extent of secondary recrystallization to a cube-on-edge texture is determined by the cooling rate from the solution temperature of the manganese sulfide inclusions.1 With a rapid cooling rate, many small inclusions rather than a few large ones are formed, which leads to increased restraint to normal grain growth and more complete secondary recrystalliza-tion. Strip samples 12 mils thick, rolled from 1-in.-thick slabs that were cooled at 130°C per min

Jan 1, 1964

By Dan McLachlan

EXPERIMENTS on ionic solids,1 Cu-A1 alloys,2 and Fe-Si alloys3 have suggested that the ability of dislocations to cross-slip is one of the most important factors governing the nucleation and growth of fatigue cracks. These experiments necessarily had to be made on materials of different composition in order to vary the propensity for cross slip. However, re-

Jan 1, 1967

By Magnus Troilius

The heat-calculations of gas-analyses involve cumbrous multiplications, which are apt to lead into errors. The foliowing tables and formulae have been found useful as facilitating such calculations, and therefore I hope that they will be of interest to some of the members. By "heat-unit" will, in the following, be understood the amount of heat required to raise the temperature of 1 kilogram of water l° Cent. All the tables refer to cubic meters at O0 and 760 mm. pressure. The following gas is chosen as an example: C02, - 4.0 vol. per cent. co, = 20.0 " CHI, - 3.5 " H, - 7.0 " N, - 65.5 " " 100.0

Jan 1, 1884

By C. F. de Mendonca, T. Kater, R. P. de Souza

Since 1976, Cia Vale do Rio Doce (CVRD) has carried out tests to develop a type of pellet made with an organic binder. Peridur is one binder that showed it could be used in industrial plants. Extensive tests were run in CVRD's pilot plant. The results are presented in this paper. The decision was made to carry out an industrial production of 50 ht (55,000 st) of pellets. The results are shown in this paper. No detrimental effects of the Peridur were observed in either the process or in product quality.

Jan 1, 1985

By J. E. Johnson

The description of the machine which coilstitutes the subject of this paper is best iutroduced by a statement of the conditions which led to its construction, which may be briefly given as follows : The ore handled at the plant to be here described* is of the variety sornetimes called by those familiar with the brown ores of the South, " Mountain," as distinguished from the " Lime-

Jan 1, 1899

By J. J. Bodmer

The four different modes, more or less practiced for subdividing slag (that is, producing slag sand), are the following: 1. Crushing the slag from the lump in Blake's crusher, by edge runners or other suitable means. 2. Blowing water, steam, cold or hot air, into the stream of viscous slag whilst it runs from the furnace. So treated, the slag takes

By A. K. Bhasin

A. K. Bhasin, (Development Engineer, Marcona Corp., San Francisco, Calif)-The author suggests the use of the term "consistency" for apparent viscosity and accordingly calls his viscometer a "consistometer." However, he goes on to refer to "consistency" as a combination of plastic viscosity, yield stress, and stability (p. 104, col. 2, line 6). Unfortunately, such conflicting terminology is encountered too often in rheological

Jan 1, 1973

By C. H. Curtis

The valuable mineral content of the current feed to the Miami concentrator is as follows: copper, 0.7 pct total; molybdenum, 0.01. Flotation of this ore yields a sulphide concentrate containing: chalcocite, 44 pct; molybdenite, 0.5; pyrite, 50.0; insol, 5.5. A combination of potassium ethyl xanthate and pentasol amyl xanthate as collectors, and pine oil as frother, are used in this flotation. Rejection of pyrite is encouraged by holding the amount of collectors used to the minimum consistent with copper recovery and by operating at high alkalinity (equivalent to 0.35-0.40 lb CaO per ton solution of pH 11.0).

Jan 4, 1950

By Magnus Troilius

The following is a very rapid method for determining copper in steel. I have found it to give results very closely agreeing with those obtained by galvanic precipitation of the copper. Five grams of steel are dissolved in a mixture of 100 C.C. of water and 10 C.C. of sulphuric acid. When all is dissolved, add 2 C.C.

Jan 1, 1883

By J. J. Bodmer

THE four different modes, more or less practiced for subdividing slag (that is, producing slag sand), are the following : 1. Crushing the slag from the lump in Blake's crusher, by edge runners or other suitable means. 2. Blowing water, steam, cold or hot air, into the stream of viscous slag whilst it runs from the furnace. So treated, the slag takes

Jan 1, 1874

By Charles H. Kline

Industrial minerals are the Cinderella of the mining I industry. Often considered as just dirt by traditional hard-rock miners and oil drillers, these products nonetheless comprise the second largest segment of the industry and the fastest-growing one. With annual sales of $5.7 billion, industrial minerals make up 22% of the dollar value of U.S. mineral consumption. By contrast, metals account for only 11%. Fuels, of course, are dominant, representing 67%. The dollar values of production and consumption for the three segments of the industry in 1968 are shown in Table I. The growth rate of industrial minerals is shown in Table II. From 1953-1968, the current-dollar value of all U.S. mineral production increased at the average annual rate of 3.8% while that of the gross national product increased at 5.9%. Industrial minerals are the only segment of the mining industry that approached the growth of the overall economy in this period, with production values increasing 5.1% a year and apparent-consumption values 5.6% These data, expressed in current dollars, include the effects of inflation. The growth in U.S. industrial minerals production is even more striking when expressed in indexes of physical production. As shown in Table III, production of all U.S. industries increased by 4.1% a year from 1953 to 1968. The growth in production of stone and earth minerals just matched this figure. By contrast, the average annual increase for oil and gas was 2.2%: for metals, 1.6% : and for coal, only 0.6 %.

Jan 1, 1970

Noranda Mines, of Quebec, signed a contract for construction of a $20 million copper refinery at Gaspe, P.Q. The plant is expected to have a 65500-ton daily capacity for both concentrator and smelter. Extensive drilling. around Gaspe has revealed more than 65 million tons of 1 to 2 pct copper in several deposits. Cerro de Pasco Corp. has called a special stockholders meeting for August 19 to obtain permission to engage in the oil and natural. gas business, in addition to its present production of zinc, lead, copper, silver and other metals. St. Joseph Lead Co. recently entered the oil development field. The United States, Canada and Great Britain have agreed to establish a permanent organization to work on unification of engineering standards. General accord has been reached on drafting standards and practices, screw threads, fittings for gas cylinders, and fits and tolerances. Permanent committees will study these fields. Reconstruction Finance Corn approved the largest sum in its history. for a mining enterprise when it loaned $94 million to San Manuel Copper. Corp., of Pinal County, Ariz. The loan will be used to increase production of copper and molybdenum, in what was described as-the biggest copper deposits in the country. Three large gold mining concerns operating in the Philippines told the Philippine Wage Board that they would be forced to close if they had to boost miners' wages 500 to $2 per day. The companies are Mindanao Mother Lodes, Benguet Consolidated, and Balatoc Mining Co.

Jan 1, 1952

By Michael Tenebaum

IN a previous investigation1 the authors studied the effect of pressure on the reduction of iron ores by hydrogen. With hydrogen as a reducing agent, the rate of reduction was increased substantially by increasing the pressure from 1 to 2 atmospheres. The results with hydrogen prompted the present study of the effect of pressure on reduction with carbon monox-ide and with mixtures of carbon monoxide and nitrogen. FEATURES OF REDUCTION PROCESS The gas stream in the lower part of the blast furnace always contains sufficient concentrations of reducing gases to complete reduction provided sufficient time is allowed for the reaction to proceed. Reducing gases react immediately with the iron oxide on the surface of lumps of ore. However, as the unreduced surface recedes from the easily accessible exterior of the lump, the reaction proceeds by virtue of the diffusion of the gases into and out of individual pieces. The rate of diffusion of gases, which undoubtedly plays an important role in the reduction of iron ores, depends on several factors, most impor-tant of which are: (1) molecular weight or density, (2) pressure, (3) tem-perature, (4) concentration gradient. Thus, the rate of reduction of a lump of iron ore at any temperature will depend not only on the specific reaction rate but also upon: (1) available surface of unreduced iron oxide, (2) rate of diffusion of the reducing gas to the reacting surface, (3) rate of effusion of the gaseous products of the reaction from the reacting surface, (4) adsorption of the gases on the reacting surface.

Jan 1, 1939