Search Documents

By Dogan E. Gücer

In the following note, with the help of a new parameter of strain hardening, the attention is drawn to the close relationship between the relative performances of steels under plastic range cycling and their strain hardening characteristics. If a cantilever beam of rectangular cross section is tested with the arrangement shown in Fig. 1 in reversed bending between constant deflection limits at the lever head, the longitudinal strain-deflection hysteresis shown in Fig. 2 is obtained. There is no lateral strain due to constraint at the rectangular test section.' If the absolute value of strain undergone between a maximum state of tension and maximum state of compression is called A, it will be seen that A decreases with cycling rapidly due to the strain hardening in the test section and the ensuing change in the bent beam profile. It will also be seen that A reaches an approximately stable value around 10th cycle. If we call the first cycle strain range, A,, and that of 10th cycle, A,,, then is an index of the strain hardening capacity at a particular deflection level. A plot of n vs ? is reproduced in Fig. 3 for two ASTM steels: A-302 and A-201. A-302 is a low alloy structural steel, A-201 a low-carbon steel. The specimens were first normalized at 1650°F for 75 min then grooved with a milling cutter; and the notches were ground to 50G finish. The final operation before testing was a stress relief at 1150°F for 75 min. The behavior of the two steels changes around ?1 = 0.8 pct or A,, = A, -n = 0.7. If these curves are compared with the endurance life curves given in Fig. 4, it will be seen that the relative performance of the two steels also change around A,, =. 0.70 pct. The steel with lower strain hardening capacity (7) at a certain strain level shows a longer endurance life, irrespective of their strength levels. Since the exponent governs strain hardening at lower strain levels than the Modulus, the relative values of both parameters also coincide with the change in n values and the relative performances of the two steels at different strain levels. These two observations indicate to the close relationship be-

Jan 1, 1962

By A. C. Stevenson

IN OUTLINING the various steps taken and the exigences met during the time of unwatering and rebuilding the burnt top equipment at the Hecla mine, the major portion of the detail is omitted and a general description of the experience only is given. All the electrical power lines were out of commission, as were the mine feeder cables. The first effort, there- fore, was to restore electrical connections. The Washington Water Power Co. immediately put a crew to work restoring the power line, it being necessary to rebuild about 4000 ft. of 66,000 volt transmission and about 2000 ft. of 2200 volt feeder. This work was rushed and power was again available at the mine sub- station about 26 hours after the fire. During the same time temporary lighting lines were strung and transformer equipment obtained, so that when electrical connection was resumed the lights were turned on and the dump well lighted that night.

Jan 1, 1924

By C. E. McManus

MANY mechanical advances have been made on mining equipment during the year 1951. There have been a number of trends established and many modifications made on open-pit equipment to increase the efficiency and availability of all the machines necessary in the moving of overburden and iron ore. Some years ago, the trend toward larger shovels for the loading of off-highway trucks began, but in the last year, it has become general practice to use the 5 to 7 ¼ -yd quarry-type shovels in the loading of haulage units. For years these larger shovels were used in the locomotive haulage pits. As the truck capacities increased from 15 to 20 to 30 tons, the need for larger loading units became apparent. Today in most mines, large shovels are in evidence and a few 8-yd shovels will be delivered this year for loading off-highway trucks. Torque Converter-Shovel The Diesel-driven shovel with its friction bands has been modernized with the torque converter. There have been about ten shovels remodeled to take a torque converter in the drive system. The large high-torque, low-speed Diesel engine was removed and replaced by a high-horsepower, high-speed, automotive-type engine. This engine was connected directly to the torque converter. The torque converter was connected to the shovel through the standard original sprocket and chain. Dual governors controlled engine performance. One governor controlled the high idle of the engine; the other governor, which is connected through a flexible shaft to the output shaft of the converter, controlled the loading of the engine. With this dual governor hook-up, the engine anticipates load conditions and is operating at high idle and full throttle before the shovel load is transmitted back through the converter to the flywheel. It has been found that with this automotive-type engine and converter, the shovel capacity has been increased about 20 pct. Also, the wear on the friction bands, breakage of hoist cables, and other mechanical breakages has been reduced materially. Alloy-Steel in Shovels The shovel equipment manufacturers have been experimenting with low-temperature-strength, high-alloy steels to combat the excessive breakage that occurs in extremely cold weather. High-nickel alloy steel has been used in critical areas that are affected by low temperatures, the most notable being dipper sticks. Most shovels ordered today are equipped with some of this special, alloy steel. More and more manganese alloy is being used for replacement parts such as shovel pads, idlers, drive sprockets, etc. Although the initial cost of these parts is considerably higher than the standard replacement items, the life of these manganese parts is considerably longer and well worth the added expenditure. Dipper-teeth repair is still a problem. Most companies use the small replaceable inserted tooth. It has become common practice among some of the companies to "job out" their dipper-tooth repairs to outside welding companies. This necessitates an additional inventory of teeth, but it does guarantee an adequate supply of replacement teeth at all times. These contractors have set up their shops on a production basis and can do an acceptable job at a high rate of speed. Thermite welding has been used in retipping teeth. To date, the process cannot be called successful but with improvements the time required to repoint the dipper teeth will be decreased considerably. The submerged arc process has been tried in the replacement of these dipper points, but like thermite welding has not proven successful. Here again, if a method can be developed to use submerged arc, the job of teeth repair will be made much easier. New model shovels in 6 ½ and 8 cu yd sizes fea-

Jan 1, 1952

By Scott Turner

PRESIDENT SCOTT TURNER officiated as chairman of the opening session on mining methods, Monday morning, Feb. 15. The first paper was that of Max H. Barber on open-pit mining in the Lake Superior district, read by C. F. Jackson. W. L. Taylor stated that liquid-oxygen explosive had been tried but that the operators are satisfied with the explosives used; lb. of dynamite breaks one ton of rock. Although black powder is considered the most effective explosive, the factor of safety has decided in favor of high explosives. Lucien Eaton told of the Michigan Lime and Chemical Co.'s large L. 0. X. plant at Rogers City, Mich. Mr. Turner referred to this plant, also said that the Bureau of Mines is shortly to issue Bulletin 349 completely covering the use of L. 0. X. from its inception. W. D. B. Motter, Jr., gave some items concerning Chuquicamata, Chile. Twelve years ago the blasts moved 850,000 to 1,000,000 tons, but average shots now move 250,000 to 300,000 tons. One pound of L. 0. X. breaks 3.7 tons, against 3.1 tons by dynamite. Another speaker told of some large dynamite blasts in open pits, one of 360,000 Ib. in March, 1931, and another of 430,000 lb. to be shot in 1932. Tests have been made to determine the effect of large shots on the surrounding country. Mr. Taylor said that 4- and 5-yd. shovels were preferable to those of 8 yd.; their performance is better and cost is lower.

Jan 1, 1932

By M. R. Tek, K. H. Coats, D. L. Katz

The performance of a gas reservoir su,bject to water drive is often affected by interference due to gas procluction or injection in neighboring reservoirs adjacent to a common aquifer. Field data available on production-pressure behavior of several reservoirs indicate that prediction of reservoir performence must include the effects due to mutual interference. A method developed to predict the performance of two or more interfering gas reservoirs, subject to specified production-iniection .rchedule.s, is presented. The method involves the comhinatiorz of the theory of unsteady-state water movernent with appropriate meterial balance consideration.s. The procedure which extends M. Mortada's treatment for interfering oil reservoirs makes use of his dimen-.sionless pressure drop quantities. prevented graphically in the literature. In order to evaluale the predictive accuracy and practical field applicability of the theory, the method has been applied to analyze the performance of two actual gas reservoirs in mutual interference. The calculations were performed on an IBA4 704 computer. The predicted performances were alro calcltlated with the interference effects ignored. The results show that considerably better agreement between calculated and observed behavior ic. obtained when the interference effects are included. INTRODUCTION Fluid communication between any number of oil or gas reservoirs adjacent to a common aquifer results in mutual interference effects on their production-pressure behavior. The theory, application and interpretation of pressure build-up behavior of oil wells, drawdown tests on oil or gas-producing formations and behavior of several storage reservoirs indicate ample experimental evidence of mutual interference. A method developed to compute the behavior of interfering oil reservoirs was published several years ago by Mortada.4 Studies conducted during the recent years on underground storage of natural gas clearly indicated the need for extending Mortada's work to the case of interfering gas reservoirs. The adoption of appropriate material balance equations in conjunction with the unsteady-state pressure interference theory yields pressure-explicit equations. Their solution, their application to a specific case history and an over-all evaluation of the developed method through the comparison of predicted and observed field performances were the main objectives of this study. DEVELOPMENT OF MATHEMATICAL RELATIONS The diffusivity Eq. 1 governs planar, radial, unsteady-state compressible liquid flow through a porous medium. ?p/?r2+1/r ?p/?r=µFc/k ?p/?t (1) The 1iterature1,2,3 contains derivations and solutions of

By AIME AIME

Further details of the 97th meeting of the Institute, at Spokane, have been sent to members in the Special Circular of May 8, 1909, and for convenience a summary of the additional information is given later in this announcement. In spite of the present small number who have joined the party, final arrangements have been made to complete the itinerary given in the circular. It is greatly to be desired, both in behalf of the Institute and in recognition of the special courtesies to be extended on the trip, that the party be made larger. Exceptional facilities to visit the many mines and smelters have been freely provided; and members are requested to make all reasonable effort to attend the meeting at Spokane and participate in the excursions. . For those who cannot take the entire trip, it may be possible to provide special Pullman accommodations after leaving the Yellowstone Park. In order to make the necessary arrangements, however, the names of members and guests contemplating this partial trip should be sent at once to Mr. Theodore Dwight, .39 West 39th St., New York, N. Y. A special train of Pullman cars will leave Chicago September 16. This train will be side-tracked at all places visited, and the sleepers will be available for lodging and the dining-car for meals (luring the entire trip, except while taking the tour through the Yellowstone Park. The general cost of the trip per member will be $300, which includes transportation, berth, and meals for the entire trip from Chicago back to Chicago, almost 6,000 miles, and the tour through Yellowstone Park, occupying in all about 30 days. Special accommodations on the train will be furnished at the following rates

Aug 1, 1909

The high-grade orebody at Miami was mined successively by top-slicing, shrinkage, stoping and under caving. The method described in this paper was developed to enable the low-grade orebody (36,000,000 tons assaying 1.06 per cent copper) to be mined at a low cost without further dilution of the grade. The method is clearly described and illustrated by drawings and photographs, and the original paper should be consulted as it is impracticable to abstract it, beyond noting that the mining cost is just under 40 cents per ton and the average grade of ore now being produced yields less copper than the mill tailing of 1915, the tons mined per day having increased from 4000 to 18,000 in the same period. Vertical and Incline Shaft Sinking at North Star Mine By Arthur B. Foote, Grass Valley, Calif. (Tech. Pub. No. 324: Class A. Metal Mining, No. 36) THE main shaft of the North Star mine is an inclined one following the main vein at an average dip of 26 deg., a vertical shaft intersects it at the 4000-ft. (incline) level, the incline continuing to the 6300-ft. level. At this point the vein was found to give out and a new vein, called the No. 1, was found to dip in exactly the opposite direction.

Jan 1, 1930

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members) Member, Graduate Colorado School of Mines. Four years' experience in West and Northwest. Two years with American Smelting and Refining Co. Wishes to join field party on geological work, mining or areal, where opportunity will be given to be of direct assistance to chief of party in solution of field problems. Age, 26. Unmarried. At liberty June 1. No. 342. Member, technical graduate, aged 30, with' 7 years' experience in concentrating and mining, desires a position of authority with reliable company. At present employed. No. 343. Member. Ambitious, energetic, tactful engineer, college graduate, married, aged 30, desires location with a large coal mining organization. Seven years with present employers -n middle west; has had broad experience in the past eight years on examination, development and construction; successful record in handling men. Position must carry responsible work and a future. Will go anywhere for proper opportunity. Exceptional references as to reliability, character and capacity for work. No. 344.

Jan 3, 1917

With a total value to date of well over $200,000.000.00 for its ore production, the Tintic mining district, which is about 100 miles southwest of Salt Lake City, ranks as one of the three main ore producing areas of Utah. In it are located the biggest silver mines of the country, silver having been the chief metal produced in the camp since its start. Tintic's silver production to date has a total value of over $1 00,000,000, approximately half of the value of the camp's ore production, the balance being roughly divided among lead, gold and copper. Discovery of the camp was made in the late sixties. Lack of transportation and ore reduction facilities delayed extensive development of the area for nearly a decade. In recent years Tintic's ore production has ranged from 350,000 to 400,000 tons annually. In 1924 the camp produced one-eighth of the silver produced in the nation with an output of 7,729,700 ounces. Its lead production was 77,765,000 pounds and its gold production 26,285 ounces.

Jan 1, 1925

By L. R. MacLead

Delivery of tailing to any part of the area by gravity from the ridge was found practicable. Experiments with asbestos-cement pipe proved it possible to use level pipe across the dams if it is fed through an inclined section in which pressure could be developed. Use of pipe to transfer the tailing to the dams was not favored because of the possibility that choking might occur. Metal flume was not believed to have sufficient wear resistance on this material and wooden flume would not withstand damage by the weather so well- Flume -action made- of 26-in diameter asbestos-cement pipe, split before curing and molded to a specified cross section, were finally approved. The flume is connected to the 24-in. diameter tail in distribution pipe by heavy concrete lateral launders. Cascades of horizontal and vertical pipe sections are used at the top of the pressure leg where scouring by high-velocity flow of tailing might occur.

Jan 1, 1942

By A. Thielen

In experiments for the production of steel the principal problem has always been the introduction into, or removal from, the iron of a definite quantity of carbon. Although the solution of this problem had engaged a more or less blindly and empirically directed effort for a long time, it was only with the development of analytical chemistry that the rôle which carbon plays in the constitution of steel was disclosed in its full significance, and that many of the problems confronting the steel-maker were thereby more clearly defined than before. For a long time, and to a certain extent even to this day, the percentage of carbon in steel has been the controlling means of deter mining its quality and hardness. In many cases the percentage of carbon alone has been relied on for judging large consignments, such as the large deliveries of wire-billets and blooms to America during the past twenty years; and though to-day the influences of the other constituents are recognized and many other considerations are taken into account, and though, moreover, some special steels, such as the Hadfield manganese steel, apparently dispense to a certain extent with the assistance of the carbon, yet fix our Bessemer, Thomas, Siemens and crucible steel the carbon still remains one of the most important constituents, and I venture to say it is indispensable. In order to produce in the Bessemer converter a steel of a certain required percentage of carbon, two methods, as is well known, present themselves. By the one the decarburization process is stopped when the desired carbon limit in the bath has been reached ; by the other the bath is completely decarburizecl, and then a calculated amount of carbon added in the form of spiegel, ferro manganese, etc. In Germany the latter method only was adopted, and it was retained when the Thomas-Gilchrist process for the production of low-Phosphorus steel from high-phosphorus iron eame into use, since from the nature of the new process complete decarburization is neces-

Jan 1, 1891

By T. A. Rickard

"The chief aim in style ought to be absolute precision", said Flaubert. "There is only one noun that can express your idea, only one verb that can set that idea in motion, and only one adjective that is the proper epithet for that noun." Let this be your motto. The engineer tries to be exact in all his measurements; he should measure his language with similar exactness. The technical term is a word of precision. It is not only precise, it is a word-saver. To the unscientific the earth is "a ball slightly flattened at the poles, something like an orange". To the scientific it is "an oblate spheroid". A similar contrast between the precision of the technical term and the vagueness of common words is afforded by a conversation between Ivanhoe and Rebecca: "' What device does he bear on his shield?' asked Ivanhoe. 'Something resembling a bar of iron, and a padlock painted blue on a black shield.' 'A fetterlock and shacklebolt azure', said Ivanhoe "-using the technical terms of heraldry. It is good style in writing, however, to adapt your manner of expression to the intelligence and experience of the person or persons to whom the writing is addressed. The description of a mine should be worded differently according as it is intended to inform a mining engineer, a director, or a bishop. REMEMBER THE READER. It is as incorrect to write in a technical way for a non-technical reader as to write in a popular way for a technical or scientific reader. That style is best which enables the writer to place himself in the closest mental touch with his reader, to establish the maximum of sympathetic understanding. Let your precision be\ proportioned to your accuracy. You should not try to be precise in matters that do not admit of

Jan 1, 1931

By Walter O. Snelling

Discussion of the paper of WALTER 0. SNELLING, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 100, April, 1915, pp. 695 to 704. A. C. McLAUGHLIN, San Francisco, Cal.-It seems to me that Mr. Snelling's work, if it is what it appears to be, is one of the most important contributions to petroleum technology that has been brought out iii the last 25 years. If his end products are what they seem to be, he has made a discovery, which, in my judgment, will revolutionize the petroleum industry. As to industrially carrying out these processes I do not think there is the slightest difficulty, for I have had some work recently where crude oils were handled successfully at a temperature of 750°F. and pressure of 750 lb. per square inch. WILLIAM A. WILLIAMS, San Francisco, Cal.-What metal did you use, Mr. McLaughlin? - A. C. McLAUGHLIN.-Ordinary seamless tubing, extra strong. WILLIAM A. WILLIAMS.-Tests were made in Dr. Rittman's experimental plant at Pittsburgh, upon samples of residuum furnished by Mr. Bell, the residuum being the remainder of the crude oil after the lighter fractions had been removed. After the material had been run through Dr. Rittman's plant, yields of from 43 to 58 per cent. of material, boiling under 150°C. were obtained. The distillate had a peculiar odor, due to the presence of benzene, toluene, and other unsaturated hydrocarbons. W. N. BEST, New York, N. Y.-What is the difference between the Rittman and the Snelling process or system? WILLIAM A. WILLIAMs.-The fundamental difference is that reactions take place under relatively higher temperatures and pressures and with none of the oil present in its original or liquid state, while the reactions secured by Mr. Snelling and other investigators have been from the liquids in the presence of some vapors. Under such conditions as Mr. Snelling operates, the temperatures and pressures used are limited and the flexibility in the control of these variables is extremely limited when compared with the Rittman process.

Jan 1, 1916

By R. G. Burdick, W. R. Peters

Shallow underground voids resulting from early coal mining and other resource recovery activities over the past several decades are now being recognized as a significant cause of ground subsidence problems. Uncertain knowledge of abondoned coal mines also imposes potential hazards in current underground mining operations, since water inundation or the release of methane gas is a serious hazard when mine excavation operations break into an abandoned mine. Requirements for detecting and mapping subversive manmade tunnels in previous work has led to the development of a surface-operated automatic earth resistivity survey system and associated computer data reduction process for military applications. Field demonstration tests of this system have resulted in successful detection of tunnels at depth-to-diameter ratios greater than 10 to one. Under the sponsorship of the Bureau of Mines, a similar high-resolution earth resistivity system was designed and constructed for use as a potential means of detecting abandoned coal mine workings. The hardware and software aspects of third new system are described together with applications of the method for surveying and mapping abandoned coal mine workings. Field tests are presented to illustrate the detection of both air-filled and water-filled mine workings.

Jan 1, 1984

By A. R. Denison

The area discussed in this report comprises a group of 38 counties lying in the northeast corner of Texas. It covers all, and extends beyond, the borders of what is commonly described as the East Texas Basin. It includes two major oil fields, Van and East Texas; two major gas fields, Bethany and Waskom; and a number of fields, both oil and gas, of lesser importance. All commercial oil production comes from beds of Upper Cretaceous age and almost exclusively from the basal member, the Woodbine sand. Gas is produced from both Upper and Lower Cretaceous beds with the newer production from the older beds. East Texas Field This field continued as in 1932 and 1933 to dominate the drilling and production situation throughout the oil business. A total of 3681 producing wells was completed in this field during 1934. This is an increase of 1215 over the 2466 producers completed during 1933. Total wells

Jan 1, 1935

By W. L. Dumoulin

A RATHER detailed description of the entire plant and leaching process was given in a paper recently presented to the Institute,1 so this paper will cover briefly only the crushing practice of the New Cornelia Copper Co. for the year, 1918. The ore, which is mined by steam shovels and loaded in side-dump cars, passes through two crushing plants. These crushing plants were constructed to crush the ore required by a leaching plant of 5000 tons daily, capacity, during a crushing period of 16 hours. The primary plant reduces to less than 3 in. (76 mm.) and the secondary plant, to ¼ in. (6.35 mm.), which is sufficiently fine for satisfactory percolation of solution through the ore in the leaching tanks, and to give good extraction. The ore is then conveyed to the leaching tanks by a system of 28-in.. (71-cm.) belt conveyors. On the way to the leaching tanks, it passes through an automatic sampling plant, where a 1-per cent. sample is taken. From the primary crushing plant, the ore is conveyed by two 36-in. (91-cm.) belt conveyors to a 10,000-ton steel storage bin, with a reinforced-concrete flat bottom. The ore discharges from the bottom of this bin onto four 20-in. belt conveyors, which deliver it to the four units of crushers in the secondary crushing plant. There is no storage bin between the mine and the primary crushing plant. The ore breaks very coarse, is very hard, and contains a great many boulders, some as large as 4 ½ by 4 1/2 by 10 ft. (1.3 by 1.3 by 3 m.). Jams form in the bowl of the coarse crusher in the primary crushing plant, as a consequence, and are freed by means of an immense steel hook operated from a 40-ton electric traveling crane.

Jan 8, 1919

By Verne C. Fryklund, S. Warren Hobbs

The Coeur d'Alene district in the panhandle of Idaho is one of the major lead-zinc-silver producing areas in the world. The value of recorded production to date has exceeded $2 billion. Country rock comprises six formations of the fine-grained, highly siliceous, and slightly metamorphosed Precambrian Belt Series. Small stocks of monzonitic rocks and several varieties of dikes intrude the sediments. The district is at the intersection of a north trending major anticlinal uplift and the west northwest-trending Lewis and Clark line of which the Osburn fault is the dominant feature. The district structure is complicated and comprises folds, some of which are overturned, and a complex of faults of diverse ages and directions of movement. Late Cretaceous stocks but are also probably Cretaceous in age. The productive veins are localized within a series of 12 subparallel, straight mineral belts that trend approximately N65°W and that appear to be controlled by deep fractures in the basement rocks. The mineral belts are in two groups, separated by 15 miles of post-mineralization movement on the Osburn fault. Veins and ore shoots are variously disposed within each mineral belt. Many crop out at the surface, but others apex several thousand feet beneath it. Local controls that influence the position of ore shoots within the mineral belts include the brittle character of host rock attitude of bedding relative to the mineralized fracture, and the amount and direction of movement on faults. Depth appears to have had little effect on the occurrence or type of ore. Ore occurs in a series of steeply dipping replacement veins of relatively simple mineralogy. Six periods of mineralization, ranging from Precambrian to Tertiary in age, are recognized. The productive galena sphalerite-bearing and tetrahedrite-bearing veins-of the main period of mineralization-are younger than the

Jan 1, 1968

By Alfred H. Bell

Illinois produced 5 per cent more crude oil in 1934 than in 1933, because there was less curtailment, and. the value of the year's production at the wells was 35 per cent more than that of the previous year. The average price of Illinois crude oil in 1934 was $1.13 as compared with $0.87 in 1933, an increase of 30 per cent. The quotas of allowable production for Illinois during 1934, as authorized by Oil Administrator Harold L. Ickes, were as follows: January, February, March, 12,000 bbl. per day; April, May, 12,500; June, July, 12,600; August, 12,500; September, October, November, 12,000; December, 11,700. No other restrictions on production were in effect during the year until Oct. 11, when it was found necessary to prorate the fields to 75 per cent, a curtailment of 25 per cent below the quota fixed by the Federal Administrator. On Dec. 1 the curtailment was reduced to 18 per cent and on Dec. 18, to 15 per cent. Production in Illinois by months during 1934 was as follows: Barrels Barrels January...................... 393,000 July........................ 394,000 February.................... 337,000 August..................... 402,000 March....................... 394,000 September.................. 378,000 April......................... 373,000 October.................... 352,000 May......................... 411,000 November.................. 305,000 June......................... 392,000 December................... 321,000 Total ................... 4,452,000 In spite of higher prices for crude oil, fewer wells were drilled in Illinois in 1934 than in 1933 (Tables 1 and 2). Of the 26 wells drilled, 10 were oil producers, 8 were in proved fields and 2 were in a new pool in Wabash County, l½ miles south of the nearest production, one was a small gas well on the Stubblefield anticline in Bond County, one was an input well for repressuring in the Colmar-Plymouth field, McDonough County, and 14 were dry holes, mostly scattered wildcat tests.

Jan 1, 1935

By Howard N. Eavenbon

The low-volatile, or smokeless, coal field of southern West Virginia is in Fayette, Raleigh, Wyoming, Mercer, Summers and McDowell counties, in the extreme southern portion of the state, and extends into the adjacent counties of Tazewell and Buchanan in Virginia. McDowell County is the largest producer, with Fayette and Raleigh counties next. The total area of the field (Fig. 1) is approximately 1600 square miles, or 1,024,000 acres. The percentage of volatile matter in the various seams ranges from 15 to 26 per cent, The upper limit of true low-volatile coal is usually considered to be 23 per cent volatile matter; above this point, the coal usually is classed as medium volatile. This limit will be used in this paper. Geological Position of Seams The smokeless seams are among the oldest coal seams in the country, as the Pocahontas group of rocks is the lowest member of the coal-bearing series and rests on top of the Mauch Chunk red shale, in or below which no coal seams of any importance occur. The Pocahontas group, or Lower Pottsville measures, has a thickness of 750 ft. in southern McDowell County, which decreases to about 350 ft. at Prince, on the New River, in Fayette County, 50 miles to the northeast. In this group, at various points, 12 coal beds have been found, of which 4 have been found in workable thickness and are now being mined. The New River group, or Middle Pottsville measures, is just above the Pocahontas group and varies in thickness from 1300 ft. in southern McDowell County to about 700 ft. along New River. At various places, 16 beds of smokeless coal have been identified in this group, of which 5 have been found in workable thickness and are now being mined. A general columnar section of these strata is shown on Fig. 2. The workable seams in these strata, arranged in geological sequence, are as shown on page 77.

Jan 1, 1932

By John T. Eastlick

The Banner mining district is about 70 miles northeast of Tucson in the southern part of Gila County, Arizona. Production from the district, valued at about $26 million, is chiefly from copper-silver-lead zinc ores. The stratigraphic section consists of Precambrian conglomerates, quartzites, dolomites, and limestones, Cambrian quartzites; Devonian limestones; dolomites, and shales; Mississippian limestones; Pennsylvanian limestones and shales; and Cretaceous volcanic and sedimentary rocks. Deformation of these rocks presumably started near the end of the Cretaceous, and extended into the late Tertiary. The sedimentary rocks were folded, faulted, and intruded by fine grained diorite, quartz mica diorite, and dacite porphyry. At least four distinct stages of mineralization are recognized. In the first stage of contact metamorphism and the second stage of hydrothermal alteration, favorable zones were prepared for ore deposition. Metallization occurred in three of the mineralizing stages. Magnetite, pyrite, and hematite were deposited near the end of the second stage of hydrothermal alteration. The third stage included the main deposition of sphalerite, chalcopyrite, bornite, and galena. In the fourth and final stage, minor amounts of sulfide minerals were deposited with a late anhydrite and quartz gangue. The ore deposits in the form of veins and veinlets, pipes, irregular massive replacements, and bedded replacements are localized by the extent and distribution of metamorphic and hydrothermal alteration, by the proximity to the intrusive contacts, and by the effects of structural development. Oxidized ores of copper, lead, and zinc constituted the principal production of the district prior to 1940, but, for the most part, supergene enrichment was of minor economic importance. The ore bodies of the district are in the mesothermal class of deposits, occurring as normal metasomatic replacement and vein types.

Jan 1, 1968