Search Documents

By J. Marshall Downey

The most fortunately situated U. S. potash producer-whether in New Mexico, California, or Utah--once simply took from the ground a mixture of sodium chloride and potassium chloride, crushed it to a maximum of 10 mesh, and separated the two salts by physical methods. He piled the sodium chloride on the desert and sold the potassium chloride to fertilizer mixing companies. Seven companies in the Carlsbad basin of New Mexico now use at least three basic processes for making the separation and at least three more processes have been or are under investigation. In addition, two companies outside the basin use two methods for taking KC1 from natural brines

Jan 12, 1958

By Christopher Haycocks, Lawrence P. Johnson, George M. Neall, James M. Townsend

No method of roof control yet devised has proven to be universally acceptable for the wide range of strata conditions experienced in U. S. coal mines. However, a relatively new innovation, the roof truss, has proven itself capable of preventing roof failures which both conventional and resin bolting could not. Presently, the economics of roof trusses are not favorable when compared to bolting due primarily to drilling and installation procedures, but this is expected to change with improved truss and equipment designs. To realize the full potential of this new method of roof control, design criteria are needed which can optimize the effect of the truss for varying strata conditions.

Jan 6, 1978

By E. C. Hopkinson, A. H. Youmans, R. A. Bergan, H. I. Oshry

A new log has been developed for quantitative formation evaluation which is based on a measurement of the length of time slow neutrons survive before they are captured in the rocks and fluids. The logging instrument employs a cyclically pulsed neutron generator and a gated scintillation counter which is synchronized with the source. The source emits short, intense bursts of 14 mev neutrons once every 1,000 microsec and is quiescent between bursts. During the period the source is quiescent, the detector is electronically actuated for two independent preselected intervals. A comparison of the counting rates during these two intervals gives a measure of the rate of decay of the slow neutrons and of the associated gamma radiation. The average neutron lifetime in most earth formations is in the range from 50 to 500 microsec. It can be measured during a continuous logging operation at conventional logging speeds. The design of the logging instrument is described and the results of tests are compared with theoretical predictiom. Formulas are developed which give the relationship between log response and formation properties. It is shown that the method is particularly sensitive to formation fluid salinity, and that salt water saturation can be measured accurately in either cased or open hole. The measurement can be made independent of borehole size, fluid type, casing and tool position in the hole by properly selecting the intervals during which the measurements are made. The results of tests with a prototype logging tool are given. INTRODUCTION A new nuclear logging system has been developed which employs the Accelatron,* an accelerator-type neutron source, and accurately measures formation brine saturation in an entirely new way. It has produced a type of formation log with better sensitivity, greater sampling depth and simpler quantitative interpretation than any other nuclear log thus far suggested. The new Neutron Lifetime Log* employs a pulsed electromechanical neutron source and a synchronously gated radiation detector. A prototype instrument has been field tested during recent months to demonstrate the operability of the apparatus and the feasibility of the method. Tests in wells and simulated boreholes have confirmed theoretical predictions and have shown that formation param ters can be measured independent of casing and other borehole parameters. Preliminary results of field tests have indicated that the log may have important and widespread applications. BASIC PRINCIPLE OF NEUTRON LIFETIME LOG The Neutron Lifetime Log is based on the fact that neutrons emitted by a source in a well are rapidly but not instantly captured by the material around the source. Their capture is a matter of statistical probability; the greater the number of capturing nuclei and the greater the "capture cross section", the greater is the probability that a neutron will be captured quickly. The average life of a thermal neutron in vacuum is about 13 minutes, but in common earth materials, the average neutron life ranges between extremes of about 5 rnicrosec for rock salt and perhaps 900 microsec for quartzite. The Neutron Lifetime Log responds to variations in this average neutron life. The theoretical basis for a log of this general type has been well understood by nuclear logging experts in many laboratories both in America and in Russia, and develop mental work along these lines has been in progress for many years. The Russian literature has reported both theoretical and experimental work1,2 but in this country there have been no published reports of progress toward a practical logging instrument. The logging instrument is designed to measure radiation produced by slow neutrons during selected intervals when no neutrons are being emitted by the source. The source is arranged to emit neutrons in bursts or pulses. During the quiescent interval between the pulses, it is possible to observe the exponential "decay" of the neutrons and the neutron-induced radiation as the individual neutrons progressively disappear due to capture by atoms in the formation or the borehole. When a short pulse of 14 mev neutrons is emitted by a source in a borehole, the individual neutrons are slowed to thermal energy within a few microsec. Thus, a cloud of "slow" neutrons is formed around the source within 10 to 50 microsec after the pulse. This cloud is most dense within a few inches of the source, and is progressively less dense out to a radius of about 3 ft, where radiation from the source is practically undetectable.

Jan 1, 1965

By C. J. McHargue

THE angles between the crystallographic planes in cubic crystals have been given by Bozorth,¹ in magnesium, zinc, and cadmium by Salkovitz,² and in tin by Nicholas. The determination of the orientation of single crystals and the study of plastic deformation require the knowledge of these angles and are often facilitated by use of a standard projection. Tables of these angles and standard projections have not been published for titanium or zirconium which have c/a ratios considerably less than those hexagonal metals for which this data is available. Accordingly, Table I has been prepared giving these angles. Fig. 1 presents a standard (0001) projection of titanium. The angle between (h1k1i1l1) and (h2k2i2l2) was calculated by means of the formula: h1h2 + K1K2 + 1/2 (h1k2 + h2k1 + cos 4 = [(hi2 + K + h1k1 + 3/4 l12 (h2² + C" a² 3/4 — l1 l2 C² k2²+ h2k2 + 3/4 —l2²) ] 1/2 c² The c/a ratio for titanium is taken from the data

Jan 1, 1953

The 112th Meeting of the Institute, and the Annual Business Meeting, will be held at the Headquarters of the Institute in New York City, Feb. 14 to 17, 1916. The Chairmen of several of the technical committees report that papers on subjects of timely interest in their respective branches have been promised. David H. Browne, who was appointed Chairman of the Committee on Arrangements, has organized his committee for active work. Members are urged to make their plans now to be present at this meeting to avail themselves of the pleasant opportunity for greeting old friends and making new ones among those engaged in the same profession.

Jan 12, 1915

By Robert H. Merrill

During the period from 1960 through 1966, the U.S. Bureau of Mines and Kennecott Copper Corp. performed an experiment to determine the changes in stress, strain, and displacement created by changes in slope angles. The experiment was performed at Kennecott's Kimbley pit near Ely, Nev. The supporting laboratory studies were made in the Bureau's Denver Mining Research Center, where final reduction of the data and summary reports are now in progress. The experiment was divided into two phases. The first consisted of the laboratory and field investigations required to select a new slope angle and configuration; the second phase consisted of a full-scale instrumented study in the west wall of the pit. The west slope was changed from an average of 45º to a slope angle that started at 45º on the south wall and gradually in- creased to 57 ½ º at the center of the west wall, and to 61 º on the north wall. The pit was deepened from 500 to about 550 ft, and approximately 2.55 million tons of waste and ore were removed from the wall.

Jan 9, 1969

By Clyde Williams

IN this war as in no former one, the use of metals has been the major factor governing success. For building new plants, new transport facilities whether by land, sea, or air, for our mechanized army, and for nearly all weapons, iron and steel has provided the basic material. Being the world leader in iron and steel production in peacetime, we soon adapted plants to production for war. Starting with a production of 66,000,000 tons of steel ingots in 1940 from a rated capacity of 80,000,000 tons which only could be reached by straining every productive device available, our industry expanded to 86,000,000 tons in 1942, and ultimately to 96,000,000 tons. To do so required expansion of every unit operation including mining, rail and water transportation, blast-furnace and steelmaking facilities, and rolling mills. New plants not only had to be built in record time but more output for each operation was essential. This performance required skillful operation and engineering techniques and also a better understanding of the physics and chemistry underlying such complex operations as the working of a big blast furnace. A vastly increased pig iron production made possible the great output of steel by an industry that had depended on scrap for its basic raw material even though sufficient scrap was unavailable. This was done by conversion of pig iron in the Bessemer either into steel or into a low-carbon product that was subsequently used in place of scrap in the open¬hearth steel furnace. Furthermore, by duplexing from the open-hearth to the electric furnace, and the construction of many new electric furnaces, our output of electric-furnace alloy steel was greatly increased. Moreover, techniques were developed by which alloy steel could be made in the open hearth with the result that our production of alloy steel reached the fantastic figure of 15,000,000 tons a year.

Jan 1, 1945

By Roswell Johnson

THE prevailing system of wells on a rectangular basis, as shown in Fig. 1-A, has developed because of the exigencies of offsetting at boundary lines. When, however, a very large tract is, being drilled, it is often possible to abandon this inferior method for the superior arrangement C- PROPER STAGGERING FIG. 1.-THREE SYSTEMS OF SPACING WELLS. known as "staggering," which is illustrated in Fig. 1, B and C. The advantages of the triangular over the rectangular method are evident from Fig. 2, computed on the basis of one well to 10 acres (4 ha.). With the triangular system, no land is more than 409.4 ft. (124.8 m.) from a

Jan 8, 1918

By B. L. Averbach

Recovery and primary recrystalliza-tion in cold worked metals are usually considered as two competing processes. Some of the effects which usually accompany recovery are: alleviation of stress corrosion tendencies, changes in thermal emf,1 damping capacity,2 electrical resistivity,2 and magnetic properties,3 and only minor changes in hardness or the related strength properties. During primary recrystalliza-tion new unstrained grains are formed at the expense of the strained matrix. These new grains eventually become visible metallographically, and nucle-ation and growth kinetics have been indicated for this process.4,5 Frequent attempts have been made to study the cold-working phenomenon by observations on the line broadening by X ray diffraction patterns. Relatively few measurements of line intensities have been made, although Brind-ley and his collaborators, 6,7,8 by means of film techniques, compared the intensities of cold worked Cu, Ni, and Rh patterns with those from chemically precipitated powders. These precipitated powders were presumed to be strain free, and it was found that the intensities for the cold-worked materials progressively decreased as the Bragg angle increased except for the first line, where there was an increase due to reduction in extinction. This was interpreted as a randomness in atomic position induced by cold work. Such randomness is similar to that caused by thermal agitation and has been described as "frozen heat" displacement of 0.08-0.10 A from the mean atomic position. In a recent study9 on the effect of cold work in metals on their powder pattern intensities, the changes in integrated intensity for heavily cold worked alpha brass were observed as a function of the annealing temperature. These measurements were made with a manually operated Geiger-counter spectrometer using CuKa radiation monochromated with a rock salt crystal. Intensity measurements were made with a scaling meter over small intervals of angle, and the equipment was so arranged that the diffracted and incident beams made equal angles with the specimen. Intensities could be compared directly by simply interchanging specimens, and comparisons from day to day were made with a standard whose line intensities did not change on aging. It was shown that a cold worked alpha brass standard was stable for at least a year. Table 1 indicates the results of the integrated intensity measurements on a 70 Cu-30 Zn brass. In the sample preparation, a brass plate was first cold rolled 50 pct and then filed, screened to —325 mesh, compacted into briquettes at a pressure of 60,000 psi and finally annealed for one hour at various temperatures up to 400°C. The briquetting pressure did not seem to influence the integrated intensities, and most of the cold work was introduced by the filing. Although this method of cold work is not quantitative, it was used to obtain random orientation (and thus uniform diffraction lines) in order to make accurate measurements of integrated intensity. Back reflection patterns were taken in each case to check the uniformity of the lines, and from the observed line broadening it was apparent that this type of plastic deformation was quite severe. Care was taken to traverse the entire background of the pattern and to assign to each peak the total intensity above this background. The bases of the diffraction lines were quite broad and spread out over several degrees, even for the narrow peaks. The theoretical intensities were calculated to include a temperature correction, a dispersion correction, and a Lorenz- polarization factor corrected for the crystal monochromated beam. In Table 1 it was necessary to match the calculated and observed values at only one point, and the rest of the experimental values were converted directly to this arbitrary scale. The integrated intensities in Table 1 are listed in arbitrary units, and the accuracy was sufficient to reproduce any of the measured line intensities to within + 1.5 units. It is evident that the percentage error on the strongest line (111) was quite low. The calculated values and the observed intensities for the cold worked material matched reasonably well. As the annealing temperature was raised, however, the intensity of the strongest reflections, particularly the (lll), decreased measurably. Since the background intensities of all of these patterns were identical, such behavior could be interpreted as a primary

Jan 1, 1950

By A. E. Lee

THE Blackwell Zinc Co., Inc., a subsidiary of the American Metal Co., Ltd., operates a horizontal retort zinc smelter at Blackwell, Okla. The plant has 14 furnace blocks of 800 retorts each, fired with natural gas on a 48 hr cycle. Over 13,000 tons of zinc-bearing material, chiefly sulphide flotation concentrates, are treated monthly to produce slab zinc and high lead-cadmium fume. In 1942 a program of rebuilding and modernizing the smelter was started. By 1947 furnace smelting capacity had been increased to a point where roasting and sintering facilities were inadequate, and it was necessary to purchase oxidized materials to supplement sinter production. The seven 210 ft Ropp roasters and three 42 in. x 44 ft Dwight-Lloyd machines then in use had been in service at least 20 years and were in need of major rebuilding. Thus it was entirely practical to consider all new equipment and a change of method rather than rebuilding and repairing obsolete units. A study of the problem indicated that roasting as such could be eliminated and roasting and sintering accomplished in one step by a modification of the Robson process,' which had been used since the early 1930's by the National Smelting Co., Ltd., at their plants at Avonmouth, England, and Swansea Vale, South Wales. Francis P. Sinn, General Manager, Zinc Smelting Operations, The American Metal Co., Ltd., who was familiar with the practice in England, suggested the use of one large machine for the entire operation from concentrate to sinter. One step sintering appeared to best meet Blackwell's plant requirements and indicated substantial savings in labor, gas, coal, and repair costs. Choice of Machine Size The sinter machine size was set at 12x168 ft for a rated capacity of 540 tons per day. This tonnage, produced on a five day week, would meet the seven day requirements of the 14 furnace blocks. The one large machine was quoted at a lower cost than two or more 6 ft wide machines of similar total capacity. Further, the larger machine could be housed in a smaller structure and only one set of equipment for charge preparation and delivery and for disposal of sinter cake was needed. One machine on a five day week made possible a concentration of the skilled operating personnel and required less men than a plant including two or more machines and related equipment circuits. Fewer units of equipment meant less maintenance, and the two down days weekly allowed ample time to repair and, if necessary, to make up lost production. Experience had indicated better sintering quality and rates with larger masses of material, not only on wider machines, but also in deeper beds. The ratio of windbox perimeter to area for the 12x168 ft machine is 0.179, compared to 0.353 for a 6x102 ft machine and 0.617 for a 42 in. x 44 ft machine. This meant less air leakage with resulting fan power savings and less spoilage of charge along the pallet sides. Performance Initial operation of the new sinter plant was made in November 1951 and regular production attained late in December. The average product sinter output during 1952 and the first half of 1953 has been 18.2 tons per hr. The average for one month has been as high as 22.4 tons per hr. Considerable experimenting with varied operating conditions accounts in part for the below capacity — 24 tons per hr — average output, and work to further improve production rate continues. A typical sinter analyses is 66.0 pct Zn, 0.3 pct Pb, 0.1 pct Cd, 0.3 pct S, 8.0 pct Fe, 2.0 pct SiO,, 0.8 pct CaO, and 0.2 pct MgO. Use of this material has made possible increases in furnace burden and improved furnace operation over the former practice using sinter made from Ropp roasted concentrates. Better lead and cadmium elimination in sintering has permitted the furnace production of slab zinc lower in lead and cadmium. Anticipated economies of operation have largely been gained. The sinter plant is operated by seven men per 8 hr shift — one head operator, three equipment operators and three sweepers — plus one oiler on day shift only. While it has been necessary at times to operate seven days a week to produce the required sinter tonnage, the five day work week usually has been adequate. Consumption of natural gas for sinter bed ignition is 200,000 to 300,000 cu ft per day. Green Ore Sintering Practice The 30 to 31 pct sulphur content of the —200 mesh zinc concentrates is the fuel used to sinter the charge, no coal addition being required. In the feed to the machine, sufficient concentrates are added to crushed return sinter fines containing 0.3 to 0.5 pct sulphur to produce a charge averaging 5.0 to 6.5 pct sulphur. Since the return sinter used in Blackwell's practice is varied from — 1/2 to — 1/8 in., the actual sintering mixture of fine sinter and concentrates is somewhat higher in sulphur. The coarser sinter particles are too large to resinter and merely aid porosity in the sinter bed. The ratio of concentrates to return sinter in the charge ranges from about 1:4 to 1:5.5. Variations are based on the appearance of pried up bed sections, bed exit gas temperature trends, windbox suctions, and return sinter size. Sufficient sulphur must be used to obtain fritting of the charge into a soft sinter cake and to aid in the elimination of lead and cadmium. Excessive feed sulphur will result in partial slagging of the cake impairing porosity and prolonging sintering time.

Jan 1, 1954

By Samuel S. Arentz, Dorsey A. Lyon

Introduction % •................. 789 The Present Sources of Zinc ..:.......... 791 Zinc Ores.................. 791 Lead-Zinc Ores................. 793 Loss oF Zinc at the Mine.............. 793 Present Method oF Extracting Zinc From Ores....... 795 Class oF Ores Suited to Zinc Retort Smelting....... 795 Concentration Processes Used for Treating Zinc Ores .... 795 Hydro-Mechanical Processes............. 795 Electro-Mechanical Processes............. 796 Flotation Processes............... 797 Losses of Zinc in Lead and Copper Blast-Furnace Smelting .. 798 Possible Future Sources oF Zinc Supply.......... 800 The Problem oF the Metallurgist and the Present Status of New Processes................. 801 Introduction A great deal of attention has recently been given to the metallurgy of zinc, and much of that which has been said and written on this subject has been in the nature of a criticism. For instance, we are quite accustomed to hearing it said that the metallurgy of zinc has stood still, that it is antiquahed, out of date, etc. We are, however, inclined to agree with George C. Stone1 when he says that, although there have been no such spectacular and radical changes as were worked in the metallurgy of copper and iron by the introduction of converters, there has nevertheless been a decided and marked progress in the metallurgy of zinc, and especially during recent years. However, it must be admitted that, due to the fact that the chemistry of zinc is so different from that of the other metals, the retort process is the only process by which zinc is produced commercially; and, moreover, that losses which occur in the zinc industry— that is, in the mining, milling, and smelting of zinc ore—are very great, for it is stated2 that probably less than 50 per cent. of the zinc mined, even

Jan 1, 1915

By E. C. Truesdale

A FEW years ago H. M. Cyr, working in the Research Laboratories of The New Jersey Zinc Co., produced a few pounds of zinc1 of such purity that no other elements were detected in it by spectrographic analysis, using the facilities then available. This zinc contained less than one ten-thousandth of one per cent of metallic impurities.2 During the decade that followed upon the laboratory production of this "spectro-graphically pure" zinc, commercial developments brought about the production of large tonnages of zinc of purity exceeding 99.99 per cent, and today zinc of 99.999 per cent purity is produced and marketed as "chemically pure" zinc. Typical analyses of present supplies of high-purity zinc are given in Table 1. TABLE 1.-Typical Analyses Percentage by Weight Sum of Zinc Pb, Fe, Pb Fe Cd Al Cd Special High Grades 0.007b 0.005b 0.0056 none 0.0106 C.P. (chemically pure) <0.0002 0.0005° 0.000052 S.P. (spectrographically pure).. <0.0002d <0.00005d a A.S.T.M. Standard Specification for Special High Grade Slab Zinc (A.S.T.M. Designation: B 6-37). b Maximum. c Fe chemically determined. Pb and Cd are spectrographically determined. d Differences between composition of C.P. and S.P. zinc are discussed later in this paper. The availability of commercial tonnages of special high-grade zinc has been the basis for the development of the zinc-base die-casting alloy industry which, in the year 1936, consumed one-eighth of the zinc used in the United States for all purposes. This and the C.P. and S.P. grades have given impetus to scientific investigations into the properties of pure

Jan 1, 1939

By A. F. Lucas

Introduction BELLE ISLE, located in the low sea marshes near Atchafalaya Bay, is the southeasternmost of the famous Five Salt Islands of Louisiana. Rising about 80 ft. (24 m.) above the level of the surrounding marsh and being some 800 acres (323 ha.) in extent, it constitutes a striking landmark on the low Gulf coast, and since the eighteenth century, when it played an important part in the operation of the buccaneers, it has been intermittently frequented by man. In 1897, the writer discovered the great mass of salt that underlies the island and shortly afterward pub-lished a brief account of the geology of Belle Isle and the neighboring salt islands.&apos; In that paper he described principally the salt, but pointed out also the occurrence of petroleum and of sulphur in the strata above the salt. Since that time the island has been extensively explored by the drill, and the developments up to 1908 have been described by Veatch2 and Harris," and Knapp.4 The writer&apos;s early conclusions as to the probable presence of sulphur in considerable quantity have been confirmed by the later drilling, some of the wells having found quantities of gas containing sulphur dioxide and a number of sulphur-bearing strata as well. Under the stimulus of the present keen demand for sulphur for war purposes, a syndicate of New York capitalists was recently formed to explore the sulphur resources of the island in more detail. Under the writer&apos;s direction, six wells were drilled for this syndicate during the winter of 1916-17. The present paper presents briefly the results of this work and sums up the present knowledge of the geology of this highly interesting locality.

Jan 9, 1917

By A. F. Lucas

Belle Isle, located in the low sea marshes near Atchafalaya Bay, is the southeasternmost of the famous Five Salt Islands of Louisiana. Rising about 80 ft. (24 m.) above the level of the surrounding marsh and being some 800 acres (323 ha.) in extent, it constitutes a striking landmark on the low Gulf coast, and since the eighteenth century, when it played an important part in the operation of the buccaneers, it has been intermittently frequented by man. In 1897, the writer discovered the great mass of salt that underlies the island and shortly afterward published a brief account of the geology of Belle Isle and the neighboring salt islands.&apos; In that paper he described principally the salt, but pointed out also the occurrence of petroleum and of sulphur in the strata above the salt. Since that time the island has been extensively explored by the drill, and the developments up to 1908 have been described by Veatch2 and Harris13 and Knapp.4 The writer&apos;s early conclusions as to the probable presence of sulphur in considerable quantity have been confirmed by the later drilling, some of the wells having found quantities of gas containing hydrogen sulphide and a number of sulphur-bearing strata as well. Under the stimulus of the present keen demand for sulphur for war purposes, a syndicate of New York capitalists was recently formed to explore the sulphur resources of the island in more detail. Under the writer&apos;s direction, six wells were drilled for this syndicate during the winter of 1916-17: The present paper presents briefly the results of this work and sums up the present knowledge of the geology of this highly interesting locality.

Jan 1, 1918

Striving to do a better job of ad- ministering the letter and spirit of the Federal Coal Mine Health and Safety Act of 1969, the Interior Department recently invited criticism-and got it. The criticisms were voiced on July 1 and 2 at the first of a series of public meetings being held by the Office of Hearings and Appeals at the Department&apos;s behest. Later meetings, at which all interested parties are invited to comment, are to be announced in the press and the Federal Register. Persons wishing to participate in the meetings should contact the Director, Office of Hearings and Appeals, 1015 Wilson Blvd., Arlington, Va. 22203. At the first Hearing, USBM Director Elburt F. Osborn outlined the progress his agency has made to date in implementing the law on three fronts: enforcement, education and research. Since the Health and Safety Act became law on December 30. 1969, he said, the Bureau&apos;s force of inspectors has grown from a mere 300 to almost 1100, while mine inspections have increased from 10,265 in 1970 to 11,021 for the first six months of 1971. On the educational front. Osborn said, the Bureau now has some 60 instructors who have trained about 50,000 miners in safety procedures since March 30. 1971. Classes at the new Federal Mine Safety Academy for both government and industry personnel begin on September 1, 1971. he added. Health and safety re- search, meanwhile, has been allot- ted $20.1 million for the 1971 Fiscal Year. Of this, $8.1 million is assigned to the Bureau and $12.3 million to contracts with universities and private companies. Admittedly, Osborn said, the mine fatality rate is still unacceptable, hut it was lower in the first half of 1971 than ever before---0.73 per million man hours and 0.31 per million tons of coal.

Jan 1, 1971

By E. W. Newman

DURING 1943 and 1944, there was an urgent need for certain grades of optical calcite (Iceland spar) for instruments for military uses. To find a supply of this material, prospecting was carried out in Montana, California and Colorado. Although some production was obtained by the work in California, the best results were from prospecting the large calcite veins of south central Montana. The bulk of the optical calcite mined during World War II has come from that area. The Bureau of Mines took an active part in the search for optical calcite in Montana. It examined most of the known calcite veins in the 70-mile distance between Wilsall, on the Shields River, and Absarokee, on the Stillwater River, and conducted exploration on several of the deposits. The Geological Survey also took an active part by mapping many of the veins. Actual mining of the calcite was performed at first by Calcite Operators, Inc., and later by the Metals Reserve Co., through an agent. A sorting plant was established at Clyde Park, where custom material could be sold. These activities stimulated mining by private operators. To be suitable for military uses, the calcite mined had to meet rigid specifications as to both size and quality. Individual crystals had to be clear and transparent and if in the form of rhombs had to measure at least 7/8 in. on each edge. Some color and a few inclusions in the calcite were allowable, but material with incipient or developed cleavages, or showing twinning other than parallel to the base, was unacceptable. HISTORY OF DEPOSITS The existence of large veins of calcite in south central Montana has long been known, and for many years the farmers of this region have used the common vein calcite for producing grit for chicken feed. According to reports, the first optical calcite produced from Montana came from the Cartwright deposit near Greycliff,1 but until recently the mining of optical calcite in Montana has been limited to spasmodic searching for small crystals suitable for making nicol prisms for saccharimeters and microscopes, or for mineral specimens. The possible need of substantial amounts of optical calcite for military uses began to appear late in 1942 and early in 1943, therefore the Polaroid company began searching for a source of supply in Montana and California. Work on the Wade property near Clyde Park was started on a small scale in the fall of 1942, by A. H. Hansen, of Clyde Park. During the winter and spring of 1943, a modest quantity of optical calcite was mined and shipped to the Polaroid Corporation, Cambridge, Mass. Most of this was produced from the "Hansen vug," which was found close to the surface. Early in the summer of 1943, mining on the Wade property was undertaken by Calcite Operators, Inc., a company organized for mining optical calcite from the Montana and California deposits. This com-

Jan 1, 1945

By Oliver Ralston

DURING experimental study on the separation of a zinc concentrate from the heavy sulfide ores of Jerome, Ariz., a great deal of attention has been given to proper activation of the sphalerite content of the ore. The sphalerite at Jerome contains enough iron to class it as a marmatite, as picked specimens have only about 60 per cent. zinc, whereas pure zinc sulfide contains 67 per cent, zinc. This marmatite in large pieces is black in color, but in dry powdered state is brown. A flotation froth made from it has a silvery black luster in comparison with a brassy luster caused by chalcopyrite which occurs in the same ores. The sample used in most of the experiments described below consisted of about 3000 lb. of diamond-drill core from the zinc-bearing orebodies of the United Verde mine, and had the following analysis: PER CENT. PER CENT. Oz. PER TON Cu 0.695 A1203 0.83 Ag 1.30 Zn 6.17 S...:: 43.35 Au 0.02 Fe 36.23 CaO 0.46 Si02 9.27 Mineralogically, this analysis is calculated to the following, which is in agreement with the microscopic examination: PER CENT. PER CENT. Chalcopyrite 2.0 Schist 3.2 Marmatite 10.32 Quartz 8.2 Pyrite 73.0 Calcite 0.9 All samples were ground in a laboratory ball mill in order to leave about 3 per cent. on a 200-mesh sieve, fine grinding being essential to liberate the minerals in the ore. Most of the Jerome ores are so intimately crystallized that reasonably complete unlocking by grinding does not take place until 800 mesh is approached. Therefore, the 200-mesh grind adopted contains a considerable amount of locked mineral grains, but not so much as. to render impossible the preparation of commercial grades of concentrate:

Jan 1, 1929

By E. Kendall Cork

The traditional financial objective for a single mine company has been to operate as frugally as possible and to pay out most of the earnings as dividends. If the business is cyclical (as it is for most metals) the dividends might fluctuate quite widely. When the mine is exhausted the company disappears. This is still quite a viable strategy for a single mine company. It is not however a viable strategy for the world as a whole. The mining industry is built by mine development companies who can mobilize the people and capital to bring new mines into production. Their skills must include marketing, engineering, finance and other politics. It is very rare for a property to be brought in without the support of a major company that can provide all these services. The exceptions will usually have some other form of big brother support, for example the U.S. government uranium contracts at guaranteed generous prices. The mine development company will seek as a minimum to perpetuate itself by developing new mines in order to replace those which are running out. The more common and more ambitious objective is to grow -- that is to add to its ore reserves and current production by developing more new mines. The financial objectives for that company are very different. Obviously if all the earnings were paid out in dividends there would be nothing left to work with. The first financial policy then is to spend an appropriate amount on exploration for new properties. The next is to retain enough of the earnings to provide the capital for new projects at least sufficient for the equity. There is no magic formula as to what proportion of earnings should properly be distributed as dividends by a growth-oriented mine development company. As a rough rule of thumb distributing half or more will probably leave too little to work on and 30% or so is probably a good balance. However the circumstances differ widely from company to company. It may be useful to set an objective for the rate of growth of a company&apos;s earnings. Some have picked rates such as 15% per annum compounded. Others have set a target in real terms which might appear as 10 or 11% plus inflation. Obviously the arithmetic of compound interest is very attractive; however in practice there is much variation. Indeed current returns from existing operations swing widely with the business cycle and there is no assurance that economic new properties will be found according to someone&apos;s arbitrary time schedule. For example, Western Mining Corporation Limited in Australia explored for 30 years with little to show for it, but then found the great Australian nickel deposits and more recently the huge Roxby Downs copper. That long dry spell could not have fitted anyone&apos;s arbitrary calendar of growth and yet they would not have found such orebodies without that long period of effort. Should they have abandoned the search? Once a new property has been found or acquired there has to be a threshold rate of return on the new capital to be invested against which to evaluate the property&apos;s economics. Conventionally this seems to be 15% after tax, a number common in other heavy industries as well. In some cases it is expressed as a lower number plus allowance for inflation. Discounted cash flow analysis is a very useful tool but it does not make the decision. In the end a "go" decision depends on judgment of many factors some of which are numbers used in the DCF calculation whose credibility must be examined. It is curious how frequently investment proposals come in with the rates of return very close to 15%. The project advocates know that a number much less than 15% will not fly and that a number much more is not necessary. With much higher nominal and real interest rates of recent years, even though before tax, logic suggests that the hurdle rate should also rise. The power of compound interest is so great that 20% is very hard to achieve in any cash flow projection but 18% may be a sensible yard - stick. Once again it is remarkable how many project proposals come in with an 18% return. On the record the mining industry as a whole has not been overly restrictive in choosing its hurdle rates of return. This is shown by the abundance of metals in recent years and the failure of metal prices to keep up with inflation. All of the foregoing is standard text book stuff.

Jan 1, 1985

PRESIDENT E DEGOLYER, District 0 NEW YORK, N Y PAST PRESIDENTS J V. W. REYNDERS, District 0 NEW YORK, N Y SAMUEL A TAYLOR, District 3 PITTSBURGH, PA FIRST VICE-PRESIDENT GEORGE OTIS SMITH, District 4 WASHINGTON, D C TREASURER CHARLES F. RAND NEW YORK, N Y SECRETARY H. FOSTER BAIN NEW YORK, N Y

Jan 1, 1923

By Claus Guenter Goetzeil

(New York Meeting, February, 1937) The object of this investigation was to determine whether silver alloys could be used instead of the currently employed insert of high-expansion Average Coefficient per Deg. C. over Range 20° to 200° C. Pure aluminum..................................... 24.6 X 10-6 Cast low-expansion Si-Cu-Ni-A1 piston alloy............ 20.0 X 10-6 High-expansion austenitic Cu-Ni cast iron.............. 19.3 X 10-6 Cast steel (0.25-0.35 C, 0.40-1.0 Mn).................. 12.6 X 10-6 Cast iron (3.15 total C, 2.16 Si)....................... 12.8 X 10-6 Pure silver.......................................... 18.9 X 10-6 austenitic ferronickel alloy, to reduce the wear of ring grooves in light metal pistons. A typical example of a piston containing a ferronickel insert is shown in Fig. 1. The high coefficient of expansion of silver made it worthy of consideration, while the small size of the insert would render its use feasible in Germany as an emergency measure. The coefficients of linear expansion of several metals and ailoys are as shown in the table above. Obviously the melting point of the insert must be high enough to prevent it from melting when the light alloy is cast around it. This imposes a lower limit of about 850" C. for the solidus of the silver alloy. Pure silver melts at about 961" C., so that the tolerable depression in the solidus is rather small. To avoid deformation of the insert during use a Brinell hardness number of at least 60 appears necessary.

Jan 1, 1937