Search Documents

By V. R. Garfias R. V. Whetsel

Production of crude petroleum in Mexico during 1935 totaled approximately 40,082,000 bbl., an increase of 1,925,000 bbl. over the previous year. Successful development continued in the Poza Rica field during the year, increasing production in that area from 3,708,000 bbl. in 1934 to 9,542,000 in 1935. The output of the South fields (Golden Lane) area decreased by 3,000,000 bbl. during the year, and the heavy-oil district of the Northern fields by 1,500,000 bbl. Production in the Tehuantepec fields showed a slight gain. Production of natural gasoline increased from 430,000 to 600,000 bbl. in 1935. Crude run to stills in local refineries is estimated at 30,000,000 bbl., some 4,000,000 bbl. more than in the previous year. Exports of crude and refined products were approximately 22,000,000 bbl., or 2,000,000 bbl. less than in 1934. Exclusive of ships bunkers, domestic consumption increased about 900,000 bbl. during the year, reaching an estimated total of 14,500,000 barrels. Only 74 wells were completed, as compared to 148 in 1934 and 91 in 1933. In proven areas 58 completions resulted in 33 producers and 25 failures. In northeastern Mexico, near the United States border, six wildcat wells were completed, all of which gave little or no encouraging results, except Rancheria No. 3, near Camargo, which is a fair-sized gas well. Four wildcats were drilled just northeast of the Northern fields (heavy-oil district), all of which were failures. A deep test was completed a short distance southeast of the Golden Lane (South fields) in Palo Blanco, which encountered small production not sufficient to exploit. On the Isthmus of Tehuantepec a wildcat well was completed for an estimated initial production of 2000 bbl. daily, a short distance south of the old Jalapa field, which was perhaps the most important new development of the year. Four other wildcats drilled in the Isthmus district resulted in failures. Fields Northern Fields (Heavy-oil District).—In the Northern fields, 18 producing wells and 20 failures were completed, as compared to 34 producers and 71 failures in 1934. The initial production of the new

Jan 1, 1936

THE story of Miami really is two stories. First, that of an excellent Porphyry Copper mine, ably managed as a business enterprise, and always among the leaders in technical progress. Concentrating its first ore in 1911, it had by 1925 paid dividends totaling $30,000,000 or $40 per share on stock that had cost the public $5 per share in March, 1908. The ore, containing 2.5 per cent copper at the start, had become progressively leaner but the recovery had tended to improve. Production costs had gone up during the World War and the early post-war period; and had come down again. In all these respects it had followed the norm. If the mine had been abandoned as exhausted and the company had been liquidated late in 1925 (a program that had been given earnest consideration in 1924), Miami would have gone down into history a first-rate mining venture; as an active and progressive participant in the great Porphyry achievement. But Miami was not liquidated in 1925; instead it started to write the record of its second and really amazing story. Near the old mine was a large body of low-grade ore containing, in place, less than 20 lb. of copper to the ton, and without, incident- ally, any considerable sweetening of gold and silver. Any method of underground mining that was cheap enough would certainly entail some dilution, so that ore as sent to the concentrator necessarily would average much less than 20 lb. As a matter of record, the average for 1929 was 16.6 lb., from which 11.726 lb. was recovered as concentrate. As already said, the exhaustion of the older orebody during 1925 was foreseen; but in 1924 the decision was reached to enlarge the concentrator and develop a new mine. An expenditure of $2,500,000 was entailed in this program. By October, 1925, the

Jan 1, 1933

By H. De Cizancourt

Peche1bronn.—So far Pechelbronn is the only producing district. Figures are given in Table 2 covering the main features of the field, but these figures call for the following remarks: First, Pechelbronn should not' be considered as a single unit, it appears, but as a succession of small oil fields, each of which is affected by very variable conditions. Consequently, certain figures concerning production per acre, production per acre-foot, pressure conditions and thicknesses of oil sands would be so misleading that they have been omitted here. Second, as regards production methods, attention is drawn especially to the fact that 42 per cent of the oil is extracted by the use of shafts and galleries and the remainder by pumping wells. Exploitation, formerly confined to Oligocene sands, has been extended recently to Jurassic and Triassic oil-bearing formations. Gabian.—This small oil field, discovered in 1924, is almost exhausted. Exploitation to date is restricted to three wells. There were no drilling activities in 1933. Exploration.—During 1933, two exploration holes have been started in France. The first, in the vicinity of Lavelanet (Ariége) on the Dreuille anticline, has reached the depth of 2400 ft,.; the second, in the Autun Permian Basin, is drilling at 1300 feet. Northern Africa Morocco.—Drilling operations have been on a large scale in Morocco. In the Gharb district (Souk el Arba area), the deepest well was abandoned in 1933 at 7014 ft. Small irregular productive horizons were encountered in the Miocene at shallow depth, oil and gas showing in the Eocene, but no commercial oil field has been discovered. In the Djebel Tselfat, near Petitjean, a small production of oil was obtained from a Jurassic horizon. In the meantime deeper formations are being explored and a new structure in the vicinity is being tested. In Eastern Morocco, a well is drilling near Taza. Production in Morocco, about 2400 bbl., has not been listed on Table 2, owing to its origin—exploration wells.

Jan 1, 1934

By G. A. Colligan, G. L. F. Powell

A new experimental technique has been developed to study nucleation behavior in eutectic alloys. It is somewhat similar to that applied by Sundquist and Mondolfo1 but with the advantages that: 1) bulk samples are undercooled instead of small droplets thus allowing the thermal behavior to be monitored by a thermocouple immersed in the sample, and 2) nucleation behavior is investigated in the same sample on either side of the eutectic composition by adding additional component to the sample under controlled conditions which preclude the addition of nu-cleation contaminants. Sundquist and Mondolfo carried out ]nucleation ex-periments on a large number of eutectic alloy sys-tems and concluded that nonreciprocal nucleation operated. If one phase a was a good nucleant for the other phase 0, then B was a poor nucleant for a. This was determined experinlentally by comparing the nucleation temperatures of 100 to 300 u diameter droplets of hypereutectic and hypoeutectic composition cooled from above the liquidus and from a temperature between the liquidus and the eutectic temperature. Primary phase a was concluded to be an efficient nucleant for the other phase B, if the following experimental result was obtained. Referring to Fig. 1, the temperature TI at which a drop of hypereutectic alloy of composition B froze when cooled from above the B liquidus was noted. This was the nucleation temperature for B in the absence of a. A drop of hypoeutectic alloy of composition A was then frozen from temperature T2 between the a liquidus and the eutectic temperature. The temperature T3 at which the eutectic nucleated in the presence of the primary or proeutec-tic a was noted. If this temperature T3 was higher than the temperature TI at which the B nucleated in a hypereutectic alloy, it was concluded that the primary a had nucleated the 6. This temperature T3, representing a certain undercooling below the equilibrium eutectic temperature Te , was designated ?TB by a> the undercooling below T, for nucleation of 13 by a. If there was no substantial difference in nucleation temperature between the hypereutectic drop cooled from above the /3 liquidus and the hypo-eutectic drop cooled from a temperature between the a liquidus and the eutectic temperature, it was considered that the a nucleated B at an undercooling equal to or greater than that at which P nucleated from a hypereutectic alloy. Sundquist and Mondolfo1 found that faceted primary crystals were good nucle-ants for metals that grow as orthogonal dendrites when present as the primary phase. Jackson2 has questioned Sundquist and Mondolfo's technique and proposed that in Sundquist and Mon-dolfo's samples, such as composition A, primary a retained B in reentrant grooves at their surfaces when heated to a temperature above the eutectic but below the a liquidus. This objection was suggested by experiments with organic eutectics where reten-

Jan 1, 1970

By A. F. Lucas

The discovery of oil in 1901 on the Spindletop dome, Texas, inaugurated a new industry on the Gulf Coast, an industry which has gran with the discovery of successive fields, until today it engages the services of thousands of workers and employs enormous capital. New fields are being discovered from time to time and doubtless some still remain to be found, though of late years discoveries have become more infrequent. Nowadays several hundred dry holes are drilled each year in a fruitless and blind effort to discover new fields, for as yet geologic science has developed no effectual method of locating the coastal oil deposits in advance of drilling. Moreover despite the occasional discovery of new fields, the total production of the Gulf Coast is today no greater than it was in 1906, for the added production of the new fields has been offset by the rapid decline and more or less complete exhaustion of some of the older ones. Careful geologic work within the fields has in some cases increased the production temporarily, but has developed no really new supplies. The Gulf Coast oil industry seems to have passed its period of greatest expansion and to be declining at a fairly steady rate, and this condition is naturally viewed with alarm by the more farsighted operators. In my opinion, the time has come for the adoption of radical and aggressive methods of prospecting; and a fraction of the money wasted yearly in drilling shallow wells in hopeless locations might well be devoted to this purpose. Many facts lead me to believe that all the salt-dome oil has had a common origin; that it has migrated up from considerable depth along lines of structural weakness; and that a deep well, properly located, stands an excellent chance of discovering the parent reservoir and thus of developing new and probably great supplies. This paper is presented as a discussion—necessarily hypothetical and based largely on personal opinion—of the possibility of encountering deep-seated oil deposits beneath the salt domes. Salt-dome Structure All of the oil produced in the coastal region of Texas and Louisiana is probably associated with salt domes, though in Goose Creek, Edgerly, and one or two other fields no salt has yet been actually penetrated. As

Jan 1, 1920

By V. W. Aubel

Among the iron-bearing ores of the world, the titaniferous iron sands of New Zealand are probably the least known to American engineers. This is not surprising in view of the fact that American ironmasters look with disfavor on any, even domestic, ores containing over 1 per cent. titanium. The possibilities of smelting titanium-bearing ores in the blast furnace are still undetermined, but the problem of their efficient reduction is becoming more important each year. There seems to be little inclination on the part of American furnace operators to tackle this problem, and they will no doubt continue to utilize the non-titanium ores at their command, leaving research and experiment to those countries not so fortunately endowed. New Zealand has, however, been intensely interested in her deposits of titanium-bearing iron sand, and during the last 50 years considerable English and New Zealand capital has been expended on this problem. The extent of the New Zealand iron-sand deposits is almost beyond measure. From Patea north to Manuka Heads, along almost the entire west coast of the North Island, these deposits exist. Wherever there is beach sand along this 300 mi. of coast line, the sand is iron bearing. It varies considerably in grade; but wherever the contour of the coast affords small bays and inlets, large dunes are found that are remarkably uniform in quality. Several of these large deposits, especially those at New Plymouth and Patea, are noted for their high iron content. The dune at New Plymouth runs between 55 and 60 per cent. of metallic iron; the panning action of the prevailing westerly winds and northwesterly currents has no doubt resulted in this concentration. Whatever the origin of this material may be, there is no doubt that deposition is going on continuously. At New Plymouth, a small artificial harbor, protected from the drifting sand by a large breakwall, has been dredged. Here sailing vessels have for years been loaded with iron sand for ballast by means of a crane and grab bucket operated from the wall of the breakwater. Thousands of tons of sand have been removed from this spot yet each succeeding storm renews the supply. The sand dune shown in Fig. 1 has been tested to a depth of 50 ft. (15 m.) without losing its

Jan 1, 1920

By Michael Chender

The current outlook for financing new copper production is not very encouraging. At a time when companies are slogging through a protracted period of low prices as well as having to accept lower profits due to more stringent tax and royalty schedules, banks are beginning to require companies to take a greater equity interest in new projects. Mineral resource financing, including copper, seems to have lost much of its appeal to the lending institutions, and loans of any kind to many of the developing countries -from which over half of new copper capacity could be expected to come-are being examined much more critically than they were in the late 1960's and early 1970's.

Jan 12, 1976

By F. M. Drake

IN this paper I propose to describe a plant which I lately erected for the Mount Stewart Lead and Silver Mining Company of Leadville, New South Wales, Australia. I am indebted to Mr. W. F. Burrow, of the Roads and Bridges Department of New South Wales, for the drawings which I present herewith, he having reduced and assembled them from my working drawings. The works are situated on a sloping hillside, but sufficient fall mas not available to have the furnace as high as desired, and at the same time have a good slag-tip and sufficient depth on the ore-floor to store a supply of ore and flux. The ore is delivered on the ore-floor (which is of the full width of the furnace-building, and extends back into the hill a distance of seventy feet) by two overhead tramways (not shown in the drawings), one on each side. From these the ore-mixture is made up on one side, while it is being taken to the furnace from the other. The fuel also is delivered by these tramways. The fluxes are stored on a floor directly at the back of the boiler and engine room. The boiler is a Cornish one, 6 feet 6 inches in diameter by 25 feet long. Its flue is 3 feet in diameter and does not contain Galloway tubes. The working-pressure is 40 pounds per square inch. The engine is an old-fashioned one, with a cylinder 16 inches in diameter by 30 inches stroke. Both the engine and boiler had been part of the plant of a defunct gold-mining company. They were very extravagant in their consumption of fuel. The blast is supplied by a rotary pressure-blower, of the Baker pattern, made in England. It has a capacity of 60 cubic feet per revolution. The furnace, which has several novel points, is shown in detail in Figs. 1, 2 and 3. The jackets are of cast-iron, and are higher than those generally used. They are different, too, in that the feedwater inlet is through a hand-hole plate near the bottom. This plate is fastened to the jacket by stud-bolts, and is provided with a baffleplate, which prevents the cooling water from impinging against the inner plate. The outlet is by a goose-neck at the top, which dis-

Jan 1, 1893

By Lucien Eaton

IN anticipation of a shortage of labor for hand-tram-ming at the Cliffs shaft mine of the Cleveland-Cliffs Iron Co. at Ishpeming, Mich., early in 1923 three 4-ton Goodman storage-battery locomotives, equipped with Edison batteries, were purchased. Storage-battery locomotives were chosen for this work because the expense and time required to put up trolley-wire and to bond the rails of the complicated system of tracks on the levels, where the locomotives were to be used, would not have been warranted by the amount of ,ore to be handled. The only changes in the tracks necessary for storage-battery locomotives were new switches and extra ties and braces on curves. The tracks were 24-in. gage, and were laid with 20-lb. rail. Edison batteries were chosen, because it was desired to charge the batteries from the trolley circuit already, in the mine, and this would have been impracticable with lead batteries. Each locomotive is equipped with 126 A-4 Edison cells, which are charged in series from the 240-volt trolley circuit while the trolley locomotives are running; and are discharged in parallel in two banks of 63 cells each. These locomotives were so successful that later 5 smaller locomotives, weighing 11/2 tons each, were pur-chased for use e with cars that are filled by hand and on levels where the amount of ore handled is small. These locomotives, built by the Geo. D. Whitcomb Co. of Rochelle, Ill., are equipped with batteries of 40 A-4 Edison cells each, the cells being the same as those, on the larger locomotives. They are charged from mer-curial-are rectifiers. These locomotives are operated by the trammers themselves, and have not special oper-ators like the larger machines. The trammers are all young men of American birth, and take quickly to the operation of machinery, and the simplicity of the con-trol on these locomotives has made special training unnecessary. A survey of the results was made by the A. C. Nielsen So., an excerpt from which follows: Eight Edison-equipped battery locomotives are now in use at an Ishpeming mine of the Cleveland-. Cliffs Iron Co. This equipment was installed to take the place of men who formerly pushed loaded cars by hand. Results have been very satisfactory and the de-pendable, trouble-free operation of the Edison batteries is considered to have been an important factor in the effectiveness of the new hauling method.

Jan 3, 1927

By H. S. McKnight

One phase of Canada's rapid development in mining and metallurgy during the past few years has been the creation of Canadian Copper Refiners Ltd., and the establishment of its modern electrolytic copper refinery at Montreal East, Quebec. Canadian Copper Refiners Ltd. is made up of three well-known metal firms whose combined activities cover the entire industry from the mine to the market. They are Noranda Mines Ltd., Toronto, Nichols Copper Co., New York, and British Metal Corporation, Ltd., London. Noranda Mines is the principal owner and provides the greater part of the raw material received by the refinery for treatment. Nichols Copper Co. designed and built the plant and is operating it under contract. British Metal Corporation acts as sales agent and markets the refinery's products. Montreal East was chosen as the site of the new refinery only after a careful survey had been made of the entire eastern part of Canada. The location chosen offers many advantages, chief of which arc the relatively low costs of power, labor, fuel and bupplies, and the fact that it is situated on Montreal harbor, the nearest seaport to the points of origin of the ram materials. All incoming material is received by rail. A majority of the plant's product is exported through the port of Montreal to European markets, being handled to the docks in railroad cars. A large proportion of the product is delivered by means of an industrial railway to the adjacent rolling mill of the Canada Wire & Cable Co., Limited. The refinery was designed to treat primarily the copper produced by Noranda Mines, Ltd. and Hudson Bay Mining &. Smelting Co., Ltd., and its rated capacity is 75,000 short tons per year. A general layout of the plant is shown in Fig. 1. Its capacity can be readily doubled, as shown by the dotted lines. Figs. 2 and 3 are sections taken through the furnace department and the tank house respectively. Except for the main office and laboratory and an auxiliary building containing the stores, warehouse, change rooms, compressor room and machine shop, the entire plant is under one roof. The type of building construction consists of reinforced concrete foundations supported on concrete piles, a steel structure covered with Robertson Protected Metal siding and a 3-in.

Jan 1, 1934

By R. D. Carpenter, R. R. Smith, E. E. Sougstad

The Union Carbide Nuclear Co., in treating low-grade tungsten and molybdenum-copper ores at the Pine Creek mill near Bishop, Calif., employs flotation for the initial extraction of the valuable mineral constituents. These minerals consist of scheelite, molybdenite, and several of the copper sulfides including chalcopyrite, bornite, and possibly chalcocite. They occur in a gangue consisting mainly of quartz, pyroxene, and garnet, with minor amounts of calcite and fluorite. This assemblage of minerals presents an unusual grinding problem because of their diverse physical characteristics. Feed for the circuit is prepared from -6-in. ore by screening on a rod deck screen to remove the -5/8 - in. material. The+5/8-in. fraction is crushed in open circuit with a 5 1/2-ft Symons shorthead crusher operated at a closed- side setting of approximately 3/8 in. The screen undersize and the conecrusher discharge are then combined to constitute the feed to the grinding circuit. The ore is ground in 6 by 5-ft grate discharge ball mills operated in closed circuit with 54-in. spiral classifiers. The classifier overflow goes directly to the flotation section of the plant. Studies of the flotation circuits have shown that the maximum recovery of the tungsten, molybdenum, and copper minerals occurs in the particle-sue range from 100 mesh to approximately 400 mesh. Further, practice has shown that the ore minerals are effectively reduced to this size range if the total ore is ground to -48 mesh. The general objective of the grinding circuit then is to reduce the feed to -48 mesh with the production of a minimum amount of slimes. The purpose of this investigation was to ascertain how well the grinding circuit was carrying out this objective. The method used was to sample the various products in the grinding section, size these products accurately, and analyze the resulting sue distributions. SAMPLE PREPARATION AND SIZING TECHNIQUES Representative samples of the different grinding circuit products, namely, new feed to the ball mill, ball mill discharge, classifier overflow, and classifier return, were taken over a 24-hr period. The samples were then dried without being filtered to avoid loss of slimes. The percentages of solids in the different products were the following: new ball-mill feed, 95%; ball mill discharge, 82%; classifier overflow, 52%; and classifier return, 84% solids. Particle sizes were determined on each product by wet-screening an

Jan 1, 1962

By Gilbert P. Moore

The production of petroleum in Argentina during 1932 was greater than in any preceding year. The total amount produced was 13,012,-756 bbl. This figure represents a decided increase in the production of oil in Argentina and can be attributed largely to the increased activities of the Royal Dutch operations at Kilometer 27 in the Comodoro Rivadavia district and those of the Standard Oil Co. of Argentina in the Salta region. Production from the Royal Dutch wells amounted to considerably more than 10,000 bbl. per day over quite a long period during the year. Of the 13,012,756 bbl. of oil produced during 1932, the Government Agency (Y. P. F.) was responsible for some 5,578,954 bbl., while 7,433,-802 bbl. were produced by private companies. Although in 1930 the Y. P. F. produced about 55 per cent of the total production and in 1930 50 per cent of the total, in 1932 its production had fallen to about 42 1/2 per cent of the total. This decrease in the proportion produced by the Y. P. F. was not due to a decrease in its production but to the decided increase in the production of private companies, particularly those two whose names are given above. One new discovery was recorded during the year. This was a well drilled by the Y. P. F. at Cacheuta in the province of Mendoza which came in pumping 80 bbl. of 15" gravity oil from a depth of 673 meters. This well was completed at approximately the same time that the provincial government of Mendoza granted a concession to the Y. P. F. and declared the whole province as a reserve in which no concessions may be granted for a period of 10 years. Under these conditions, the federally operated Y. P. F. will have no competition in the Cacheuta area from private companies such as they have in the other three fields of the republic. The Y. P. F. wildcat west of Comodoro Rivadavia at Pampa Maria Santissima on the Rio Senguerr was completed as a dry hole during 1932. This we11 was reported as a producer in 1930 by persons returning to this country from Argentina but it appears that they had been misinformed. The site of this test has been abandoned and a new location made north of the Rio Senguerr.

Jan 1, 1933

SUCCESSFUL development of a new process for heat hardening of pellets made from taconite concentrates was announced by Arthur G. McKee & CO., steel plant engineering and construction firm of Cleveland, and Allis-Chalmers Mfg. Co. An order for the design, engineering, and materials for a plant incorporating the process, has been received by the McKee Co. from the Reserve Mining Co. for its new E. W. Davis Works at Silver Bay, Minn. It is estimated that this plant will cost around $19 million and when in full operation, will turn out 12,000 tons of pellets per day.

Jan 10, 1954

By L. R. Raymond, G. G. Binder

One primary purpose of hydraulic fracturing as a well stimulation technique is to overcome formation damage. The literature provides ways of designing fracture treatments and evaluating their results but not of incorporating formation damage in vertically fractured wells. Results of an investigation of this problem are presented in this paper. Prediction of stimulation ratios in vertically fractured, damaged wells is accomplished with a mathematical model relating stimulation ratio to relative conductivity of fractures whose lengths are not more than about half the drainage radius of the well. Comparison of results from the new model to results in published predictions verify its utility; these results also show that the range of stimulation ratios that can be predicted for undamaged wells is extended to include relative conductivities of less than 300. This extension is important when using fracturing to stimulate wells with high production rates and high native formation permeabilities. For example, large increases in daily oil production rate can be obtained with stimulation ratio increases as low as 1.25. The importance of complete fracture fill-up (uniform proppant packing) is shown through use of the mathematical model. If, at the mouth of a fracture, only a small fraction (1/2 percent) of the total fracture length is not packed with proppant, nearly all the polential stimulation increase is lost. Proppant crushing, compaction and embedment have been shown in laboratory studies to be responsible for low fracture conductivities in wells producing from highly stressed formations. Equipment and methods for testing the effect of stress (overburden) on conductivity of fructures in consolidated and unconsolidated sands are discussed in this paper. Laboratory tests with simlilated fractures in cores from both types of formations showed that crushing, compaction and embedment seriously affect conductivity. Results indicate that similar laboratory tests should be made when accurate knowledge of fracture conductivity is needed to assure good stimulation results for important wells. The chief factor in stimulation ratio reduction was found to be overburden pressure, but the size and type of proppant and the hardness of the formation have significant effects. Fracture conductivity reductions of up to 50 percent were observed with sand propping fractures in consolidated cores; a reduction of 83 percent was measured for an unconsolidated core. The range of effective overburden pressures for which conductivities were measured was from 100 to 5,000 psi. An example fracture design and evaluation problem indicates the usefulness of considering formation damage in planning well stimulation jobs. When damage exists, but its extent and the degree of permeability reduction are not estimated from diagnostic tests, the formation permeability used in planning the job may lead to under-designing. As the example shows, too low a target stimulation ratio can lead to much lower production rates (by half) than could be attained otherwise. Solutions of equations representing several special cases of the mathematical model are presented in graphical form and details of the derivations of the equations are given in the Appendix. INTRODUCTION Since its inception in 1947, hydraulic fracturing has proven to be an effective and widely accepted stimulation technique. In the past 18 years the ability to execute a successful hydraulic fracturing treatment has been substantially increased. The development of design and evaluation procedures1,2 has been one of the major contributions to this increased skill. However, as the art of hydraulic fracturing has moved closer to a science, new problems concerning the design and evaluation of the optimal hydraulic fracturing treatment have arisen. Three questions are pertinent to these problems. I. How is a fracturing job evaluated in a damaged well? 2. What is the effect on the stimulation ratio of not filling the fracture in the vicinity of the wellbore? 3. What is the effect of overburden pressure on fracture conductivity and, consequently, the stimulation ratio? A primary objective of fracturing a well is to stimulate production by overcoming wellbore damage. Presently. however, there is no rational basis for designing or evaluating the optimal fracturing treatment in a damaged well. All present fracture design and evaluation techniques assume that proppants can be uniformly placed in fractures. This assumption may be in serious error, particularly for the portion of a fracture directly adjacent to the wellbore. In this area, turbulence of the injected fluid can cause the proppant to be swept farther into the fracture. Also, loss of fluid from the fracture to the

JAMES GAYLEY (President), R W RAYMOND (Secretary), FRANK LYMAN Treasurer) T A RICKARD NEW YORK, N Y CHARLES H SNOW NEW YORK, N Y R W RAYMOND NEW YORK, N Y (Terms expire February, 1906 ) JAMES GAYLEY NEW YORK, N Y FRANK KLEPETKO NEW YORK, N Y FRANK LYMAN NEW YORK, N Y (Terms expire February, 1907 ) JAMES DOUGLAS NEW YORK, N Y JAMES F KEMP NEW YORK, N Y ALBERT R LEDOUX NEW YORK, N Y (Terms expire February, 1908 ) Council PRESIDENT OF THE COUNCIL JAMES GAYLEY VICE-PRESIDENTS OF THE COUNCIL GEORGE W MAYNARD NEW YORK, N Y JULIAN KENNEDY PITTSBURG, PA CHARLES D WALCOTT WASHINGTON, D C (Terms expire February, 1906 ) WILLIAM P BLAKE TUCSON, ARIZ THOMAS F COLE ,DULUIH, MIFF IRVING A STEARNS WILKES-BARRE, PA (terms expire February, 1907 )

Jan 1, 1910

By Theron Wasson

The Central Michigan area held first place in the state during the year. Midland and Isabella, the leading counties in 1932, produced most of the oil in 1933. The Porter field southeast of Mt. Pleasant and along the same structural trend saw the greatest drilling activity. In Porter during the year 117 new wells were drilled. Under proration these wells produced 3,583,617 bbl., or nearly one-half the total for the state, which has been estimated at 7,947,695 bbl. The Porter field is already outlined on all sides except the northwest. It probably reached its peak in 1933. Unless a new field of some magnitude is developed in 1934, Michigan will see a continuous decline. The Greendale extension to the old Mt. Pleasant field furnished the new flush for 1932. In 1933

Jan 1, 1934

Section 67 Department of Conservation and Development, State of New Jersey, State House Annex, Trenton, N. J. H B Kummel, State Geologist For lists of publications, maps and geologic folios, address the above. Where price of postage is noted, in the following list of available publications on geology, the postage is only to New Jersey and

Jan 1, 1933

By John D. Clark

ONE'S lifetime does not usually offer the opportunity to observe and be a part of the commercial development of an entirely new material. Petalite has been known for over a century, but at first it was presumed rare. However, it was found to be so abundant that it has become a new and extremely useful industrial tool.

Jan 10, 1950

By W. W. Mein

IN March 1949 the Calaveras Cement Co. was sued by five landowners whose properties are located in the vicinity of the plant. These landowners—all of them cattle ranchers—sued for dust damages of $120,338 and for an injunction preventing the company from casting dust upon their properties in injurious quantities. The issue was split, the jury deciding the amount of damages and the court handling the injunction features. The action came to trial before a jury in April of that year and resulted in damages being awarded in the amount of $7,508. A month later the court issued its injunction requiring recovery of stack dust to an 87 pct minimum. The Calaveras plant, shown in Fig. 1, is located three miles from San Andreas in the heart of the Mother Lode country, about 45 miles east of Stockton, Calif. Since it is in a small town, the company's responsibilities to its employees and to the community are different from those of plants located in large centers of population. Construction of the plant was begun in 1925, and production was started the following year. Standard gray Portland cement as well as several specialty cements are produced. Production facilities have been continually enlarged so that the present capacity is more than double what it was 25 years, ago. The most important item in the company's expansion program was the purchase in 1945 of an 11 ft 3 in. x 360 ft Allis-Chalmers kiln which had been declared surplus by the Defense Plant Corp. The company is now able to produce about 2,500,000 bbl of cement a year, and employment at the plant is approximately 300. The production of cement has always involved a dust problem, solution of which has been attempted in a number of different ways. By far the most efficient method of catching dust discharge is electric precipitation. Soon after the company went into production in the 1920's, the landowners near the plant began complaining about dust discharge. The company settled the matter by paying them a total of $27,000 for dust damages incurred during the period from 1929 to 1938. In the latter year the two-unit Cot-trell Electric Precipitator shown in Fig. 2 was installed and collected over 85 pct of the dust resulting from operation of the two 11 ft 3 in. x 10 ft x 240 in. kilns. From 1938 until 1946 the landowners registered no objection and were apparently satisfied with that dust recovery. In 1946, however, the substantially higher production resulting from operation of the new kiln immediately overtaxed the facilities of the existing two-unit precipitator. In a short time claims for dust damages were again received from the landowners. The company informed them that because of postwar shortages it would take several years to install a new precipitator. The company stated that it intended to purchase an additional precipitator and offered in the meanwhile to pay the landowners a fair amount to cover their damages. This offer was rejected and the landowners filed suit in the Superior Court of Calaveras County asking for total damages of $120,-338 and for the injunction outlined above. Case for the Ranchers The attorneys for the plaintiffs produced three different types of witnesses: first, the landowners themselves and members of their families; second, other cattle raisers who were sympathetic to the plaintiffs; and third, several types of technical experts: veterinarians, soil chemists, and an aerial photographer. The testimony of these witnesses was designed to establish that the flue dust from the plant had not only damaged the land and the forage, but had also caused fluorine poisoning to their animals. By a combination of these causes, the plaintiffs attempted to prove substantial loss of profits.

Jan 1, 1952

By R. Maddin

IN analyzing the relation between the orientation of new grains and that of the deformed matrix of axially extended and recrystallized single crystals of face-centered cubic metals, a two-stage rotation process" is generally used where the first rotation is made in order to account for an "adjustment of orientation to the environment of strain."&apos; It has been argued that in spite of the difference of orientation, which may amount to as much as 12" (in a brass),&apos; between the octahedral plane as observed in the parent lattice and in the recrystallized grain, it is believed to be a common plane in the sense that it constituted the nucleus in the parent strained crystal from which the new grain grew.&apos; A possible source of the deviation in orientations of a common pole in the new grain and that of the deformed single crystal matrix from which it has grown may be found in the distribution of strain resulting from the plastic deformation. It might be expected in view of the incongruent nature of shear&apos; that the perfection of the octahedral plane along which glide has occurred is disrupted and that this disruption constitutes the strain from which nuclei of new grains can grow during recrystallization. Evidence for the existence of strain along glide planes was first detected by Taylor" in 1927 and substantiated by Collins and Mathewson&apos; in 1940. In their investigations, however, the deformed single crystalline specimens (aluminum) were cut mechanically along the glide planes followed by mechanical polishing. X-ray exposures (glancing angle) of only 8 min with filtered radiation were used. It was later shown&apos; that this type of surface preparation did not remove with all certainty the mechanically disturbed surface. It was felt that a re-investigation of this phenomenon using more refined techniques might reveal a more correct extent of the strain resulting from the deformation which might correlate the deviation of the common pole of the recrystallized grain with the acting slip plane of the matrix crystal. In accordance with these thoughts, a single crystal of a brass (70/30 nominal composition) M in. in diam x 5 in. long, tapered as in previous experiments,&apos; was extended and carefully documented with respect to elongation and shear. Disks about % in. thick paralle&apos;l to the primary slip planes were cut from the specimen by means of an etch cutter." These disks represented volumes of the specimen which had been extended 0, 5, 10, 15, and 20 pct. Copper Ka monochromatic radiation was obtained by reflecting 35,000 v copper radiation from the c-cleavage face of a pentaerythritol crystal. The monochromatic radiation was collimated and led on to the disk set at the proper 0 angle for reflection from the primary (111) planes. The monochromatic beam was aligned in a plane containing the active slip direction. Following a 10 hr exposure at the theoretical Bragg angle, the disk was reset at 0 + 1°, 0 — 1", 0 + 2", 0 — 2", etc., until no Bragg reflection was obtained. The disk was then rotated 90" about its polar axis, and the same X-ray procedure was used. The results are shown in Table I. It may be seen from the results in Table I that the plastic deformation (20 pct elongation) produces fragments of the glide plane which are rotated or tilted as much as 25 " from the normal position on a purely block slip model. In addition to the large variation in 0 angle in the slip direction, there is a variation in 0 as much as 20" in the direction at right angles to the direction of slip, i.e., <110>. In view of the results shown, it may now be argued that the strain distribution finds its origin in the incongruent nature of the slip process.&apos; The use of the two-stage rotation process seems valid in attempting to explain the relation between the orientation of recrystallized grains and the matrix from which they have grown. Acknowledgment This work was sponsored by the ONR under Contract Number N6 onr 234-21 ONR 031-383. The author would like to thank N. K. Chen for reading and correcting the manuscript. References &apos;R. Maddin, C. H. Mathewson, and W. R. Hibbard, Jr.: The Origin of Annealing Twins. Trans. AIME (1949) 185, p. 655; Journal of Metals (September 1949). &apos;J. A. Collins and C. H. Mathewson: Plastic Deformation and Recrystallization of Aluminum Single Crystals. Trans. AIME (1940) 137, p. 150. eN. K. Chen and C. H. Mathewson: Recrystallization of Aluminum Single Crystals After Plastic Extension. Unpublished. 4 C. H. Mathewson: Structural Premises of Strain Hardening and Recrystallization. Trans. A.S.M. (1944) 38. :&apos;C. H. Mathewson: Critical Shear Stress and Incongruent Shear in Plastic Deformation. Trans. Conn. Acad. of Arts and Science, (1951) 38, p. 213. "G. I. Taylor: Resistance to Shear in Metal Crystals, Cohesion and Related Problems. Faraday Soc. (1927) 121. &apos;R. Maddin and W. R. Hibbard, Jr.: Some Observations in the Structure of Alpha Brass After Cutting and Polishing. Trans. AIME (1949) 185, p. 700; Journal of Metals (October 1949). &apos;R. Maddin and W. R. Asher: Apparatus for Cutting Metals Strain-Free. Review of Scientific Instruments (1950) 21, p. 881.

Jan 1, 1953