Search Documents

By Will H. Coghill, Fred D. DeVaney, R. G. O’Meara

The size of ball mills in the ore-dressing industry has increased from about 4 ft. in each dimension to 10.5 ft. in diameter by 8 ft. in length. In the cement industry they are as long as 45 ft. Plainly the trend has been toward larger mills. The common belief is that the big mills economize in floor space and first cost, but the advantage with respect to friction has not been clearly defined. In the ball-mill studies at Rolla, Mo., laboratory mills as small as 2 by 2 ft. have been found as efficient in terms of the amount of grinding per unit of net power as mills 6 by 4 or 6 by 12 ft. Therefore, if supremacy can be claimed for the big mills, advantage must come from other sources. The advantage to be considered here is reduced loss by friction or dead load. In the study to determine whether big mills have relatively less loss by friction the commercial catalogs were used for fundamental figures. The dimensions and weights of Table 1 are taken from the catalogs (the last line gives data on a Rolla laboratory mill). The net power—that is, the power expended within the mill for grinding—is calculated by a new formula.' The assumed speeds are each at 70 per cent of their theoretical critical speeds, and the mills are loaded to the center with balls. In other words, they are assumed to be working under analogous conditions and are set for good grinding. In the last column the ratio B: A shows that the larger commercial mills are lighter per unit of net power than the smaller mills, and more of the motor output should therefore go into grinding. The laboratory mill seems to have some advantage over the larger mills; it would be expected to be light because it has no liners.

Jan 1, 1935

By J. B. Newkirk, A. H. Geisler

Certain of the permanent magnet alloys provide ideal systems for the study of the kinetics of the precipitation reaction and the correlation of structure with properties. One such system, Cu-Ni-Fe, was found by Bradley1,2 to exhibit a coherent transition state in the precipitation process analogous to that reported for Al-Cu alloys somewhat earlier.3 The attractiveness of some perrnanent magnet alloys for study lies in the fact that vertical sections of the ternary phase diagram in certain regions of composition (Fig I) have as their prototype the binary Ni-Au diagram. Alloys of this type decompose into products that have the same crystal lattice type but only slightly different lattice parameters. The advantages that such alloy systems oA&apos;er for study over the usual in which an intermetallic compound is formed are many: 1. Since the precipitate has the same crystal strutture as the matrix, complex atomic movements are not required to form the new lattice. 2. Similarly, complex orientation relationships are not involved for both the matrix and the precipitate would be ex. petted to have the same orientation. 3, Small &,registry of the decomposition products at equilibrium (in contrast with Cu-Ag alloys) is conducive to extensive coherent growth in the transient state and thus the transition lattice can be detected by the usual X ray diffraction methods. 4. Finally, the relative quantities of precipitate and depleted matrix can be varied from 0 to 100 pet* thus permitting wide freedom for the study of the effect of cornposition on coherent growth and properties. In the Cu-Ni-Fe alloys of appropriate composition, the face-centered cubic precipitate and also the depleted matrix when first formed are coherent with the parent matrix.1&apos;2 The two have the same <Jo parameter as the original matrix but they are both tetragonal; the precipitate has an axial ratio c/a < I while that of the depleted matrix is c/a > I. When coherency is lost they assume the normal face-centered cubic structure with the depleted matrix having a lattice parameter greater than the original matrix and that of the precipitate less. Such a mechanism would also be expected for CU-Ni-CO alloys because of the similarity in constitution but this had not been demonstrated. The Present investigation was conducted on a CU-Ni-CO alloy. The constitution diagram and magnetic properties of these alloys have been fairly well established, however, no previous determinations of mechanism of precipitation and no correlation of structure with properties had been made. Thus, an alloy of this system Was chosen for a comprehensive investiga-

Jan 1, 1949

By J. B. Newkirk, A. H. Geisler

INTRODUCTION CERTAIN of the permanent magnet alloys provide ideal systems for the study of the kinetics of the precipitation reaction and the correlation of structure with properties. One such system, Cu-Ni-Fe, was found by Bradley1,2 to exhibit a coherent transition state in the precipitation process analogous to that reported for Al-Cu alloys somewhat earlier.3 The attractiveness of some permanent magnet alloys for study lies in the fact that vertical sections of the ternary phase diagram in certain regions of composition (Fig I) have as their prototype the binary Ni-Au diagram. Alloys of this type decompose into products that have the same crystal lattice type but only slightly different lattice parameters. The advantages that such alloy systems offer for study over the usual in which an intermetallic compound is formed are many: I. Since the precipitate has the same crystal structure as the matrix, complex atomic movements are not required to form the new lattice. 2. Similarly, complex orientation relationships are not involved for both the matrix and the precipitate would be expected to have the same orientation. 3. Small disregistry of the decomposition products at equilibrium (in contrast with Cu-Ag alloys) is conducive to extensive coherent growth in the transient state and thus the transition lattice can be detected by the usual X ray diffraction methods. 4. Finally, the relative quantities of precipitate and depleted matrix can be varied from o to 100 pct* thus permitting wide freedom for the study of the effect of composition on coherent growth and properties. In the Cu-Ni-Fe alloys of appropriate composition, the face-centered cubic precipitate and also the depleted matrix when first formed are coherent with the parent matrix.1,2 The two have the same [ao] parameter as the original matrix but they are both tetragonal; the precipitate has an axial ratio c/a < I while that of the depleted matrix is c/a > I. When coherency is lost they assume the normal face-centered cubic structure with the depleted matrix having a lattice parameter greater than the original matrix and that of the precipitate less. Such a mechanism would also be expected for Cu-Ni-Co alloys because of the similarity in constitution but this had not been demonstrated. The present investigation was conducted on a Cu-Ni-Co alloy. The constitution diagram and magnetic properties of these alloys have been fairly well established 4,5 however, no previous determinations of mechanism of precipitation and no correlation of structure with properties had been made. Thus, an alloy of this system was chosen for a comprehensive investiga-

Jan 1, 1948

By I. J. Logan, Warren L. Baker

By 1950 or soon thereafter facilities will be available in foreign countries for the production, transportation, and refining of about 4,305,000 bbl per day of crude oil—a volume not far short of current United States output. This is indicated by announced plans for foreign expansion, - some of the work being already under way. The projected potential production is about 1,500,000 bbl per day or 50 pct above the record-setting foreign production of 2,810,000 bbl daily in 1946. The scheduled new foreign facilities are equivalent to almost one third of the present facilities of the United States. Fears that so much additional foreign oil may flood world markets and disrupt the domestic industry of the United States are not justified. The projected foreign expansion apparently has been planned on a sound business basis, with careful consideration of the world&apos;s actual need for all the projected additional production. Materially increased world demand for petroleum promises to absorb the increased supplies without ill effect upon the domestic industry. Even by applying conservative estimates of both foreign and domestic demand, it is indicated that world requirements can absorb the projected larger foreign output and still permit continued increase in United States production. World demand would have to increase only 5.7 pct per year in the 1947 to 1950 period to absorb the prospective supply. Such an increase may be conservatively projected, in view of past and current trends. Introduction Recent announcements of plans for expanding petroleum facilities in the Middle East and Venezuela foreshadow an unusually sharp increase in foreign production in the immediate future. Therefore, the next few years will bring far-reaching changes in world petroleum affairs, with foreign petroleum production and other activities assuming much greater importance than formerly. Tabulation of figures on development already under way or planned indicates that in the next several years facilities will be available for producing, transporting and refining twice the prewar production of foreign fields and about 50 pct or nearly 1,500,000 bbl a day above their record-level output of 1946. To say that foreign fields may be producing such an enlarged quantity by 1950 is, of course, a statement of great significance to everyone connected .with the oil industry and especially to those of the American petroleum industry. A production of 1,500,000 bbl daily is equal to the combined yield of the states of Oklahoma, Kansas, Illinois, Louisiana, Arkansas, Mississippi and New Mexico. This means that within the next several years foreign petroleum facilities will undergo a new expansion equivalent to one third of the present facilities of the United States. To think of such an expansion in foreign production is to raise at this meeting the question of what this prospective foreign development means for the United States, the American petroleum industry in general, and the American engineer and technologist in particular. It is only logical to question whether or

Jan 1, 1948

By Warren L. Baker, I. J. Logan

By 1950 or soon thereafter facilities will be available in foreign countries for the production, transportation, and refining of about 4,305,000 bbl per day of crude oil—a volume not far short of current United States output. This is indicated by announced plans for foreign expansion, - some of the work being already under way. The projected potential production is about 1,500,000 bbl per day or 50 pct above the record-setting foreign production of 2,810,000 bbl daily in 1946. The scheduled new foreign facilities are equivalent to almost one third of the present facilities of the United States. Fears that so much additional foreign oil may flood world markets and disrupt the domestic industry of the United States are not justified. The projected foreign expansion apparently has been planned on a sound business basis, with careful consideration of the world&apos;s actual need for all the projected additional production. Materially increased world demand for petroleum promises to absorb the increased supplies without ill effect upon the domestic industry. Even by applying conservative estimates of both foreign and domestic demand, it is indicated that world requirements can absorb the projected larger foreign output and still permit continued increase in United States production. World demand would have to increase only 5.7 pct per year in the 1947 to 1950 period to absorb the prospective supply. Such an increase may be conservatively projected, in view of past and current trends. Introduction Recent announcements of plans for expanding petroleum facilities in the Middle East and Venezuela foreshadow an unusually sharp increase in foreign production in the immediate future. Therefore, the next few years will bring far-reaching changes in world petroleum affairs, with foreign petroleum production and other activities assuming much greater importance than formerly. Tabulation of figures on development already under way or planned indicates that in the next several years facilities will be available for producing, transporting and refining twice the prewar production of foreign fields and about 50 pct or nearly 1,500,000 bbl a day above their record-level output of 1946. To say that foreign fields may be producing such an enlarged quantity by 1950 is, of course, a statement of great significance to everyone connected .with the oil industry and especially to those of the American petroleum industry. A production of 1,500,000 bbl daily is equal to the combined yield of the states of Oklahoma, Kansas, Illinois, Louisiana, Arkansas, Mississippi and New Mexico. This means that within the next several years foreign petroleum facilities will undergo a new expansion equivalent to one third of the present facilities of the United States. To think of such an expansion in foreign production is to raise at this meeting the question of what this prospective foreign development means for the United States, the American petroleum industry in general, and the American engineer and technologist in particular. It is only logical to question whether or

Jan 1, 1948

By Joseph G. Wargo

An investigation of trends in exploration expenditures for a selected group of mining companies was undertaken for the interval 1968-1971. These trends were compared with financial factors that are associated with various groups of companies and the implications of these trends are indicated. The sample consists of 21 mining companies, of these, 19 are listed on the New York Stock Exchange and 2 are listed on the American Exchange. Twenty are American, one is Canadian. All are fundamentally "mining companies" in that they derive the bulk of their income from the ex- traction, sale, and at times, fabrication of metals from their own mines. This is in contrast to companies which have mineral exploration departments but derive the bulk of their revenues from sources other than mining, such as oil and gas sales. No companies which can be considered strictly as exploration companies are included in the sample. This definition held up in 1968, however, its strict application became more difficult through the years. In 1971, three or four of the companies were changing their character in that they were phasing out of the mining business and deriving a substantial part of their income from activities other than mining.

Jan 5, 1973

By P. L. De Bruyn, R. J. Charles

The transfer of kinetic energy of translation into other forms of energy by impact is a fundamental process in most crushing and grinding operations. During and after the impact process the original source energy may be accounted for in any of the following possible forms: 1) Kinetic energy of translation of both the impacted and impacting objects. 2) Kinetic energy of vibration of the components of the impact system. 3) Potential energy as strain energy of the components of the system or in the form of residual stresses. 4) Heat generated by internal friction during plastic deformation or during damping of elastic waves. 5) New surface energy of fractured materials. At any instant during the impact process only the strain energy of the components of the system can contribute directly to the brittle fracture process. If fracture is the desired result, as in comminution, it would seem advantageous to choose or arrange the conditions of impact so that a maximum amount of the original kinetic energy could be converted to strain energy at some moment during a single impact. The present work deals with determination of these desirable conditions for a simple case of impact and application of the principles involved to general cases of impact.

Jan 1, 1956

By Frederick J. Rich

INTRODUCTION Coal characterization involves a variety of analyses which are designed to yield as much information as possible about the properties of coal. The types of analyses which are now regarded as necessary for any truly quantitative assessment of coal include the following: 1. proximate analysis 2. ultimate analysis 3. petrographic analysis The two traditional forms of analyses are the proximate and ultimate types. A proximate determination reveals the amount of moisture, volatile matter, fixed carbon, and ash which are present in the coal. Nowadays, a sulfur determination is usually included in the proximate analysis. The ultimate analysis, in contrast, includes a major alkaline oxide determination, which tells how much sodium, calcium, and potassium are found in a sample. Sulfur forms, i.e. sulfide and sulfate vs organic sulfur, are also identified as well as carbon, hydrogen, oxygen, nitrogen, and trace element concentrations. Proximate and ultimate analyses have been used for many years. The petrographic analysis, one which identifies and quantifies organic microcomponents of coal, is a comparatively new technique of coal characterization. Petrography adds great detail to a coal analysis and, to be sure, is a necessary component of any complete analysis. Coal is not at all uniform in its composition. Material from different mines within one coal-producing region will display varia-

Jan 1, 1983

By Charles M. Stone, Dale S. Preece

Introduction The Strategic Petroleum Reserves (SPR) is a national program dedicated to storage of large quantities of crude oil in leached salt caverns in the Texas-Louisiana gulf coast area. The program has required storage in existing caverns at each site and includes plans to leach new ones. The structural stability of each cavern depends on the behavior of the surrounding salt. In the past cavern stability has been predicted based on experience with other caverns in the vicinity. With the development of good non-linear finite element structural computer programs, it is possible to predict stability before the cavern is created. An important step in verifying the applicability of these predictive methods is comparison of analytical and field data. The analytical data come from finite element analyses of a specific cavern where the laboratory determined material properties and an approximation to the cavern geometry are used as input. These comparisons have been made for caverns in the Bayou Choctaw Dome (Louisiana) and Eminence Dome (Mississippi) with reasonably good correlation being obtained between measured and predicted volumetric response of the caverns. This paper discusses 1) the acquisition of material properties, 2) the finite element program SANCHO, and 3) the comparison of analytical and field data for each of the caverns.

Jan 1, 1982

By George B. Clark

THE geological data emphasized so successfully in prospecting for new deposits, that is, structural controls, strength of solutions, and type of mineralization, are basically those required for successful exploitation. In the mining of newly discovered deposits the most economical methods should be employed as early as possible to keep the overall cost per unit produced at a minimum and to permit maximum extraction of valuable minerals. A crucial question is: How can geological data be translated into useful quantitative results which will aid in achieving this end? H. E. McKinistry1 has suggested that a solution may be reached in one of two ways: 1-the usual approach, use of judgment based on experience; or 2-mathematical calculations and tests on models, both subject to certain limitations. He also suggests that in addition to better use of geology more case data and theoretical data are needed on which to base sound judgment. Further research, therefore, is necessary. Perhaps in this field the emphasis should be on more specialization in mining methods and ground movement by men with thorough training in physics, engineering, geology, and underground mining. These specialists would be equipped to point out the most economical and scientific methods of exploitation.

Jan 8, 1954

By A. D. Kennedy

No major breakthroughs in concentration technology were made during the year, but solid advances were made in engineering. Perhaps the most significant was the growing acceptance of the unified or "systems approach" to mineral extraction, processing, refining, transportation and marketing. Under the systems approach, transportation is no longer some- one else&apos;s business, but a high cost item within the planning engineer&apos;s purview. The Savage River pipeline 1,2 and the Marconaflo process3,4 for land and ocean transport of iron ore slurry, are examples showing that evaluation of transportation as part of a unitized system can lead to innovation, and the determination of the physical location of some of the operations. There is even speculation that the cost reductions possible by ocean transport of iron ore slurry may bring in more plants using direct-reduction steelmaking processes.4 Some perennial problems can be solved by application of the systems approach; for example, under this concept the replacement of three small shovels in the pit with two larger shovels is not permissible on the basis of lower operating costs; the resulting change in ore blending upon metallurgical performance must first be evaluated to prove whether or not the change is economically beneficial to the entire operation (perhaps new storage-blending facilities will be indicated).

Jan 1, 1970

By J. Kent Smith

Vanadium is generally spoken of as a rare element; but, even in the light of our resources as known a couple of years ago, this description could be accepted in a qualified sense only. In fact, vanadium is very widely distributed, being a constituent of most clays, while even caustic soda has been shown to contain almost regularly a minute proportion of it, although the quantity in each case is so small as to render impracticable the extraction of the metal therefrom with profit. The opening-up of a large deposit of vanadium sulphide ore in South America has put a new phase on the commercial outlook of vanadium, the technical value of which for the improrement of steel has been proved by rigorous scientific investigation. This sulphide ore has the following analysis: Per Cent. Vanadium sulphide,.39.84 Molybdenum sulphide,.1.57 Nickel sulphide,.........1.49 Iron sulphide,.........4.07 Arsenic sulphide,.. nil. Copper sulphide,.. nil. Manganese sulphide,..nil. Free sulphur,..30.57 Phosphorus,...nil. Silica,....13.60 Alumina,..........2.46 Combined water, 5.00 Carbonic acid, Lime, magnesia, potash, soda and unaccounted for, 100.00 Being a free-burning ore it is calcined with ease, losing 45 per cent. of its weight in the process. The calcined ore has the following analysis:

Jan 1, 1908

By AIME

D R. GILLSON, who was born in Evanston, Ill., in 1895, is another one of those geologists who received his early inspiration and foundation in his science from that great teacher at Northwestern University, the late Professor U. S. Grant, and then went on to give his time and interest to Institute affairs-like those other Northwestern men, Arthur Blair, Gilbert Cady, Charlie Behre, Evan Just, Ian Campbell, Clayton Ball, and many others. After serving in the Navy in the first World War as, of all things for a geologist, a commissary officer on a transport, he went on to MIT and took his doctor&apos;s degree under Waldemar Lindgren in 1923. He even assisted in mineralogy at Harvard and thus had training under another great teacher, Charles Palache. He taught mineralogy and petrography at MIT from 1923 to 1928. After several summers of field work as an assistant in the U. S. Geological Survey, Dr. Gillson joined the staff of the du Pont company.

Jan 1, 1947

By Linn M. Farish

The reported production of petroleum in the Dominion of Canada for 1930 was 1,555,199 bbl., an increase of 455,373 bbl. over 1929. Alberta accounted for nearly all the production with Ontario and New Brunswick, the other two productive provinces, contributing less than 1 per cent, of the total. The completion of about 25 producing wells in Alberta was more than sufficient to offset the decline of the older wells in that province and the small decline in Ontario. The production of about 5000 bbl. in New Brunswick represents a restricted output to meet the market demand. Table 1 shows the production by provinces for the past 10 years. The consumption of natural gas for all purposes in Canada reached a new record of practically 40,000,000,000 cu. ft. in 1930, which was a considerable increase over 1929. The estimated value of the gas output was $10,500,000, against a little over $5,000,000 for the total petroleum production. Gas wells in Alberta accounted for over 75 per cent. of the total, with Ontario second and New Brunswick a poor third. The outlook for 1931 is for very little change in production of either gas or oil in Ontario and New Brunswick but for a substantial increase in both in Alberta.

Jan 1, 1931

By Charles H. Fulton

FOR some time it has been thought that there should be > closer relationship between the members&apos; of the Institute engaged in education in the mining schools, the mining, metallurgical, ceramic, and geological departments of universities, and the members of the Institute actually engaged in the production of mineral products and the operation and direction of works. The American Society of Chemical Engineers and the American Ceramic Society have for some years past devoted especial attention to the educational matters of their respective fields. The Engineering Foundation, representing the great engineering societies of the country, is deeply interested in technical education and maintains a Committee on Educational Research.

Jan 1, 1932

By Dewitt T. Ring

Reliable and detailed data covering the enormous number of wells drilled and the long historical production of the state, many of which were never recorded until recent years, render it impossible to gather statistical material suitable for the Institute&apos;s standardized form. The total production of crude oil in Ohio for the year was 3,654,503 bbl., which is less than the total production in the United States for the peak day of August 1937. For a period of eight years, from 1895 to 1902 inclusive, Ohio produced more oil than any other state. During the year, 1271 tests were drilled in the state, or 114 more than in 1936. Of these, 317 were oil wells, with an initial production of 7088 bbl., an average of 22.3 bbl. per well; 503 were gas wells, with an initial open flow of approximately 222,441 M cu. ft., or 443 M cu. ft. per gas well drilled; 451 were dry holes, that is, 35 per cent of the total completions. A number of factors account for the steady decline of oil production in Ohio. In the state, at the close of thc year, there were fewer than 28,122 producing oil wells. In 1936, there were 30,150 operated oil wells with an average yearly production per well of 126 bbl. The production for 1937 averaged 130 bbl. per well. During the year, 2028 oil wells were abandoned. In other words, old wells are being abandoned more than six times faster than new ones are being drilled. Since the inception of the oil and gas industry in Ohio, between 150,000 and 160,000 wells have been drilled in the state; new potential territory, offering desirable locations for either oil or gas, is becoming increasingly more difficult to find; the dry-hole percentage will continue to increase. Prices Another factor directly affecting the crude situation during the year was the matter of price and proration of Pennsylvania grade oil. The posted price for Pennsylvania grade in Ohio on June 7 was $2.37 per barrel; at the close of the year, it was $1.70 per barrel, or a reduction of 28 per cent in price. In addition to this price cut, a 50 per cent pro-

Jan 1, 1938

By L. L. Peterson, W. C. Morgan

This paper discusses some of the problems involved in predicting the productivity of a shovel and truck fleet in a new set of operating conditions. More specifically, it concentrates on the problems of predicting the travel times on the haul and return portions of the truck cycle under new profile conditions and the prediction of the interaction effect between the shovel and truck at the loading point. The ability to calculate the travel times for a new road profile is not new. Additional corrections of these calculated times for expected actual operation can be made. In considering the interaction between the loader and the hauler, there are two approaches that can be taken. Probably the most accurate method of predicting the shovel-truck interaction is a simulation of the step-by-step operation considering the variation in cycle times of the shovel and trucks. This is usually called a stochastic simulation and requires input describing how these cycle times vary. However, by understanding the causes of this shovel-truck interaction it is possible to make sufficiently accurate predictions with much simpler methods. Haulage Cycle Established from Existing Operations For the purpose of this discussion let us assume that the problem involves trying to predict the productivity of a single shovel-truck fleet at some future time in an existing operation. Let us also assume for simplification that the new operation to be simulated has the same loading and pit conditions and the same dumping conditions as did the existing operation. Therefore, the only difference would be the difference in the hauling profile for the new operation. The problem then becomes one of predicting the change in the travel times on the haul and return portions of the cycle, and in determining the change in interaction between and the shovel and trucks with the new truck cycle times.

Jan 12, 1968

By Ernest J. Stocking

ENGINEERS are the key men in our war program today. Upon the technical knowledge and skill of the engineer and upon his administrative and executive abilities rests the entire success for the production of vital materials of the war. Naturally the work load of the engineering examining unit of the U. S. Civil Service Commission has increased greatly since our active participation in the war. At present, over 550 separate requests for certification of eligibles are received by the engineering unit per week. These represent more than a fourth of the total requests received for personnel by the Commission&apos;s central office at Washington and represent a recruitment work load of three to four times that carried by the whole Commission previous to January 1940. These requests represent a minimum of a thousand vacancies to be filled each week, while an average week will produce, at present, approximately 1400 vacancies and a weekly maximum may approach well over 2000 vacancies.

Jan 1, 1942

By Earl Oliver

IN times like these, the A. I. M. E. and similar societies have their greatest usefulness. . . . Individuals and companies acting alone in the development of public opinion are merely voices crying in the wilderness. United and organized they make a great force that can and does influence public action. . . . What part, if any, then, shall the A. I. M. E. take in these great stabilization processes of civilization? Shall it help to give direction and force to scientific knowledge which comes within its field of activity or shall it merely develop more of it? . . . Is it the A. I. M. E.&apos;s function to help bring system, order and direction out of this situation so that the world can again have forward economic movement, or should it rest on its oars until other agenciess develop that public understanding and direction so necessary for economic progress? As we understand the functions of the A. I. M. E. Petro¬leum Division, they are to discover and promote knowl¬edge for the benefit of society on the mining of oil and gas. To the individual member of the Petroleum Division, there are certain advantages of social and professional contacts, but the collective purpose is that described. And the individual is benefited by membership only as the Division measures up to the purposes of its existence. Consequently, the welfare of this Division and that of its members depends on the extent to which it keeps pace with the needs of society on matters relating to the mining of oil and gas.

Jan 1, 1932

By R. H. Heyer, J. L. Bray, M. E. Carruthers

It is well known that iron markedly improves the physical properties and casting characteristics of aluminum bronzes. The use of 1 to 4 per cent iron as the principal modifying addition has become common practice in many foundries melting aluminum bronzes. Although the beneficial effects of iron are unquestioned, there is some uncertainty regarding the structural changes caused by it in the basic copper-aluminum system. It is agreed that a new constituent appears in abundance when the iron content reaches 2 to 4 per cent. This constituent, which frequently occurs in shapes resembling clover leaves, is sometimes assumed to be an aluminum-iron intermetallic compound. If this were correct we might expect a change in the structural relationships of the matrix in the direction of decreased aluminum content. On the other hand, it has been reported that iron has a negligible effect in altering the fundamental relationships of copper-aluminum alloys1 Others2&apos;3 have reported an additive coefficient. Apparently it will be necessary to know the equilibrium relationships between the phases of the copper-aluminum-iron alloy system to establish any such theory as fact. When this has been done it may very well be that a further revision in the structural relationships may be necessary to describe the changes to be expected in commercial cast alloys. It was with this latter problem before them that the authors attempted to determine the change in the copper-aluminum relations with respect to iron. Objects of the Investigation In certain investigations carried out by the authors for a plant producing a large tonnage of cast aluminum bronzes the structures

Jan 1, 1936