Search Documents

By W. H. Bassett

A 10-year, sea-water, corrosion test of tubes of several copper alloys has shown that many alloys withstood attack by solution, pitting, and dezinkification; a 1-year, salt-spray test of sheet-metal specimens of the same composition showed the same results. THE late J. P. Sparrow, chief operating engineer of the New York Edison Co., carried out a series of practical tests on condenser tubes of several copper alloys and reported on the results to the Association of Edison Illuminating Companies at its meeting in' September, 1913. In the preparation of these tubes the senior author had the pleasure of cooperating. Copper-zinc alloys in the proportions of 60-40, 70-30, 80-20, 90-10, and Admiralty metal, which is in effect 70-30 with 1 per cent. of tin, were tried. Monel metal and several copper-nickel alloys, and 8, 5, and 3 per cent. aluminum bronze were also tried. At the time of this report, the aluminum bronze had been in service for 4 1/2 years and seemed to be giving especially good results but later it began to fail and showed no substantial improvement over Admiralty metal. Monel metal was unsatisfactory and the nickel alloys apparently did not give better service than the Admiralty alloy. Previous to the publication of the report, and after considerable discussion, it was agreed that a test where tubes of different kinds could be under laboratory observation would be advisable, so the apparatus described here was set up in The American Brass Co.'s Waterbury Laboratory. This was fitted with tubes of copper, brass, bronze, nickel silver, cupro-nickel and other alloys, and the test started Oct. 11, 1912. Salt water from East River, New York harbor, was barrelled and transported to the laboratory for the test. A fresh supply, completely replacing the water in service, was obtained at the end of each six months period.

Jan 1, 1925

By AIME AIME

IN times of stress nations pick strong men to lead them. Similarly the Coal Division selected forceful Larry A. Shipman, fuel engineer for the Southern Coal and Coke Co., Knoxville, Tenn.. to lead it through the year 1945. He was born in Indianapolis May 13, 1891. Following graduation from a technical high school in that city Larry began his fuel career approximately 35 years ago attached to one end of a scoop shovel, firing locomotives for the Pennsylvania Railroad. At the end of two years he transferred to the New York Central Lines and held these jobs successively: locomotive fireman, engineer, fireman instructor, supervisor of instructors, and fuel engineer.

Jan 1, 1945

By Charles Legrand

The power plant of the Burro Mountain Copper Co. is located near Tyrone, N. M., at 5,950 ft, elevation. It is interesting because it uses the largest stationary Diesel engines in the United States. The general layout of the plant is shown in Figs. 1 and 2. The building is of steel-frame construction with hollow-tile walls and corrugated-iron roof; the floor is concrete and all windows have steel frames, making a fireproof building. The building is made to accommodate one more electric generator unit, which is being installed; also two 4,000-cu. ft. air compressors direct-connected to three-cylinder engines with the same size cylinders as the electric units. The power plant consists of two 815-kva., 60-cycle, three-phase, 6,600-volt, 180-r.p.m. generators, direct-connected to five-cylinder, two-cycle Diesel engines; the necessary circulating pumps for cooling water, cooling towers and oil storage tanks. A portion of the power is used in the same building as the generating units to run one of two 200-kw. rotary converters delivering 260-volt direct current, and a 2,500-cu. ft. air compressor, delivering air at 95 1b.-pressure, direct-connected to a 400-hp., 6,600-volt, three-phase synchronous motor. The remainder of the power is used to run a 1,500-ton concentrating mill 3 1/2 miles from the power house, various hoists, pumps and motors about the mines and the lighting and water-works of the town of Tyrone. The direct current is used for electric traction in the mine, also to run hoists and motors that were installed before the new power plant was built. Due to the large hoists that take starting peaks of 250 kw. and the 10-ton electric locomotive that takes at times 150 kw., the load is extremely variable, as shown in Fig. 3. The two five-cylinder vertical Diesel engines, which are rated at 1,250 b.hp. at sea level, have cylinders of 525-mm. diameter (20.6 in.) and

Jan 1, 1917

By R. Maddin, W. R. Hibbard

A series of X ray experiments conducted by G. I. Taylor' in 1927 and later substantiated in 1939 by J. A. Collins2 both on axially strained aluminum single crystals, revealed evidence that during single slip crystallite rotation occurs in such a manner that " all parts of the material rotated about the transverse direction in the plane of slip."l The actual method of preparing the specimens for X ray examination is not discussed in detail by Taylor except to say that "this specimen was cut parallel to the plane of slip, as calculated from measurements of marks in the surface of the specimen. It was ground and etched till the effect of the new cuts had disappeared. This was verified by applying the same treatment to an un-distorted specimen. The X ray reflectionsl in this case were perfect ones."' Collins, on the other hand, cut his crystals in a mechanical shaper. These surfaces were polished on No. 1, No. 1/0, No. 2/0 and No. 3/0 papers and on a broadcloth lap using No. 600 alundum as a polishing medium. "Finally, the surface was deeply etched in Tucker's reagent. An unde-formed crystal was prepared in the manner described and X rayed to determine whether or not the machining and polishing operations had produced any strain or distortion in the crystal. The Laue spots all seem to be sharp, free from tails and streaks indicating no detectable strains had been introduced in the crystals." Taylor's X ray technique involved the use of "homogeneous X rays from an iron anti-cathode"; whereas Collins used Ka radiation of copper at 31kv and 20 milliamperes. Glancing angle X ray photograms were taken (1) with the axis of rotation of the spectrometer table in the plane of slip and at right angles to the slip direction, and (2) with the axis of the spectrometer table lying along the slip direction. However, eight minute exposures were used in each case and the angle setting of the spectrometer table was increased by one degree for each exposure. With the discovery of the action of three slip systems3 in the plastic deformation of single crystalline alpha brass where, formerly, only one had

Jan 1, 1950

Homestake's Bulldog Mountain Operation near Creede, Colorado, in the San Juan Mountains at an elevation of nearly 2,750 m (9,000 ft), is subjected to short summers and long cold winters. Creede’s history dates back to 1889 when silver ore was discovered; and by 1892 production of over a million dollars per month was being shipped from mines located along the Amethyst Fault. The Bulldog Mountain Fault remained relatively untouched by the early prospectors. The United States Geological Survey recognized the potential of this fault in 1960, which led to the staking of many claims over the structure. Homestake leased properties in 1963 and in mid- 1964 a tunnel was started at the 2,956 m (9,700 ft) level with encouraging mineralization being encountered. In 1968 a decision was reached to build a flotation mill of 318 mtpd (350 stpd) capacity. The erection of the mill was completed in early 1969, six years after the first exploration was begun. Since initial start-up, extensive drifting has been done on several separate levels. Two underground hoist installations serve the various levels and many thousand feet of vertical mining operations. Due to the unconsolidated nature of the vein, a new unique underhand cut-and- fill mining method was developed. This procedure is the reverse of the normal cut-and-fill and proceeds from the top down under cemented sand fill, which, while expensive, has greatly reduced s toping hazards. Prior to 1977, a considerable quantity of silver was lost in the slime fraction of the ores processed because of oxidation and other inherent characteristics of individual minerals. Due to Homestakefs favorable experience in treating the slime fraction of the Lead, South Dakota gold ores, experiments with leach methods to recover silver from the slimes by Carbon -In -Pulp offered' the potential for additional silver recovery. Work was begun on the Carbon-In-Pulp plant in April 1976 and completed in December of that year at a cost slightly exceeding $2 million. The C. I. P. plant was designed for 136 mtpd (150 stpd) of current plant slimes plus 227 mtpd (250 stpd) of slimes dredged from the old tailings during the summer season. The sand fraction of the flotation

Jan 1, 1981

By P. Nelson, K. L. Gunsallus, A. R. Ingraffea, J. F. Beech

INTRODUCTION Fracture toughness, KIC, is an intrinsic material property and is a measure of the energy required to create new surface area in a material. Fracture toughness measurements can be made for a wide range of rock types (Ouchterlony, 1980). As a measure of energy of comminution, fracture toughness might be used for more sensitive predictions of Tunnel Boring Machine (TRM) performance than are possible with other index measures in current use. This paper describes part of an ongoing, comprehensive, analytical/experimental program aimed at evaluation of KIC in such a role. The program includes efforts to: 1. Provide a firm analytical basis for a test specimen geometry: the core-derived short-rod. 2. Develop simple, inexpensive testing equipment and techniques. 3. Evaluate the accuracy of the above by testing rock and other materials and comparing the measured fracture toughness with those obtained by other methods. 4. Measure fracture toughness of a substantial number of different rocks from three ongoing TBM projects. 5. Compare fracture toughness results with other strength measures. 6. Compare all test results with observed TBM performance in the three projects. Presented here are summaries of all but the last of these efforts. Comparative evaluation of KIC as a more senstive rock property for TBM performance prediction will be the subject of the oral presentation and a subsequent paper.

Jan 1, 1982

By Gerald Sherman

MINING asbestos ore by caving at Thetford Mines, Quebec, has been described in the Transactions of the Canadian Institute of Mining and Metallurgy in papers presented by the staffs of The Asbestos Corp. Ltd., in 1934, and Johnson's Co. Ltd., in 1941. The production by caving prior to 1949, in round figures, has been 14,500,000 tons of ore by The Asbestos Corp. and 5,500,000 by Johnson's Co. They are the only caving operations in asbestos at the present time. The Jeffrey mine of the Canadian Johns-Manville Co. at Asbestos, 40 miles southwest of Thetford, is well along in preparations for caving, and The Bell Asbestos Mines Ltd. at Thetford Mines, will follow their examples later. GERALD SHERMAN, Member AIME, is Consulting Engineer, Johnson's Co. and Canadian Johns-Manville Co., New York, N. Y. AIME San Francisco Meeting, Feb. 1949, and New York Meeting, Feb. 1950. TP 2828 A. Discussion (2 copies) may be sent to Transactions AIME before May 31, 1950. Manuscript received Nov. 2, 1949. Nearly all of the asbestos produced by the western hemisphere is mined in those districts of Canada. Since it has been the subject of a number of technical papers, this contribution is offered as a review of progress. Some introductory information seems appropriate, for few members of the American Institute of Mining and Metallurgical Engineers are familiar with the mineral, or how asbestos deposits differ from others in caving characteristics. Asbestos is found in peridotite, a basic intrusive rock irregularly altered to serpentine and erratically fractured, well enough to cave in bulk, but leaving many blocks of solid ore of all sizes scattered through the deposit. Chrysotile is the variety of asbestos produced in Canada. Its fibers are the most valuable commercially, having a good proportion of long fibers, strong, silky, flexible, and suitable for spinning. The fibers occur in all lengths, from the microscopic to 3 in., or more, the shorter are more abundant. Their values depend on length combined with other qualities noted above. They occur as veinlets filling fissures in the peridotite, with crystals compactly arranged in parallel across the cracks. They are sometimes lightly frozen to the walls but the partings are distinct, often marked by particles of magnetite adhering to the fiber ends. Sometimes they break away from the rock in slabs an inch or more in thickness. In wide fissures the fibers are not always continuous, the "broken fibers" being separated by lines of parting with occasional scattered grains of magnetite, which is an injurious mineral to be elirninated when possible. In addition to the chrysotile ''Cross fiber," some "slip fiber" is found in fault fractures in limited quantities of less valuable character. With the exception of the Asbestos Corp, ore, in which the content is said to be more uniform, asbestos is eccentrically distributed through the peridotite. It is the general impression that the higher grades are more often found in hard rock. There are rich pockets and leaner areas which range down through various grades to minor barren sections. Wholesale mining is necessary to make sure of recovering all the high grade for there are no reliable indications of its existence. Ore selection only appears in constructing assay-grade limits for caving. The mill yield of the Thetford ore body in 1934 was 6 to 10 pct of the ore milled, made up of all classes, with occasional runs up to 15 pct or so. Quotations for Canadian asbestos* are as follows: Per Ton No. 1 Crude (% in. and longer) $896 @ $960 No. 2 Crude (Y8 to % in.) 350 @ 545 Spinning (less than % in.) 204 @ 378 Other classes, price diminishing with length. Shorts or "refuse" 24 @ 46 • From Eng. and Min. Jnl., Nov. 1948. Asbestos of even superior quality for electric insulation is found in Arizona limestone. It is white, containing very little combined iron, but occurs only in small quantities.

Jan 1, 1951

By Gerald Sherman

MINING asbestos ore by caving at Thetford Mines, Quebec, has been described in the Transactions of the Canadian Institute of Mining and Metallurgy in papers presented by the staffs of The Asbestos Corp. Ltd., in 1934, and Johnson's Co. Ltd., in 1941. The production by caving prior to 1949, in round figures, has been 14,500,000 tons of ore by The Asbestos Corp. and 5,500,000 by Johnson's Co. They are the only caving operations in asbestos at the present time. The Jeffrey mine of the Canadian Johns-Manville Co. at Asbestos, 40 miles southwest of Thetford, is well along in preparations for caving, and The Bell Asbestos Mines Ltd. at Thetford Mines, will follow their examples later. GERALD SHERMAN, Member AIME, is Consulting Engineer, Johnson's Co. and Canadian Johns-Manville Co., New York, N. Y. AIME San Francisco Meeting, Feb. 1949, and New York Meeting, Feb. 1950. TP 2828 A. Discussion (2 copies) may be sent to Transactions AIME before May 31, 1950. Manuscript received Nov. 2, 1949. Nearly all of the asbestos produced by the western hemisphere is mined in those districts of Canada. Since it has been the subject of a number of technical papers, this contribution is offered as a review of progress. Some introductory information seems appropriate, for few members of the American Institute of Mining and Metallurgical Engineers are familiar with the mineral, or how asbestos deposits differ from others in caving characteristics. Asbestos is found in peridotite, a basic intrusive rock irregularly altered to serpentine and erratically fractured, well enough to cave in bulk, but leaving many blocks of solid ore of all sizes scattered through the deposit. Chrysotile is the variety of asbestos produced in Canada. Its fibers are the most valuable commercially, having a good proportion of long fibers, strong, silky, flexible, and suitable for spinning. The fibers occur in all lengths, from the microscopic to 3 in., or more, the shorter are more abundant. Their values depend on length combined with other qualities noted above. They occur as veinlets filling fissures in the peridotite, with crystals compactly arranged in parallel across the cracks. They are sometimes lightly frozen to the walls but the partings are distinct, often marked by particles of magnetite adhering to the fiber ends. Sometimes they break away from the rock in slabs an inch or more in thickness. In wide fissures the fibers are not always continuous, the "broken fibers" being separated by lines of parting with occasional scattered grains of magnetite, which is an injurious mineral to be elirninated when possible. In addition to the chrysotile ''Cross fiber," some "slip fiber" is found in fault fractures in limited quantities of less valuable character. With the exception of the Asbestos Corp, ore, in which the content is said to be more uniform, asbestos is eccentrically distributed through the peridotite. It is the general impression that the higher grades are more often found in hard rock. There are rich pockets and leaner areas which range down through various grades to minor barren sections. Wholesale mining is necessary to make sure of recovering all the high grade for there are no reliable indications of its existence. Ore selection only appears in constructing assay-grade limits for caving. The mill yield of the Thetford ore body in 1934 was 6 to 10 pct of the ore milled, made up of all classes, with occasional runs up to 15 pct or so. Quotations for Canadian asbestos* are as follows: Per Ton No. 1 Crude (% in. and longer) $896 @ $960 No. 2 Crude (Y8 to % in.) 350 @ 545 Spinning (less than % in.) 204 @ 378 Other classes, price diminishing with length. Shorts or "refuse" 24 @ 46 • From Eng. and Min. Jnl., Nov. 1948. Asbestos of even superior quality for electric insulation is found in Arizona limestone. It is white, containing very little combined iron, but occurs only in small quantities.

Jan 1, 1951

By David E. Nicholas

INTRODUCTION In this paper, a numerical process for selecting a mining method, with the emphasis on underground mass mining techniques, such as caving, induced caving, and stoping, is proposed. In the past, selection of a mining method for a new property was based primarily on operating experience at similar type deposits and on methods already in use in the district of the deposit. Then, the chosen method was modified during the early years of mining as ground conditions and ore character were bet- ter understood. Today, however, the large capital investment required to open a new mine or change an existing mining system make it imperative that the mining methods examined during the feasibility studies and the method actually selected have a high probability of attaining the projected production rates. Although experience and engineering judgment still provide major input into the selection of a mining method, subtle differences in the characteristics of each deposit, which may affect the method chosen or the mine design, can usually be perceived only through analysis of measured characteristics. The parameters that must be examined when choosing a mining method include: 1) geometry and grade distribution of the deposit; 2) rock mass strength for the ore zone, the hanging wall, and the footwall; 3) mining costs and capitalization requirements; 4) mining rate; 5) type and availability of labor; 6) environmental concerns; and 7) other site-specific considerations. This paper encompasses a detailed look at the first two parameters since they, plus mining costs, have the greatest impact on the selection of a mining method. The proposed method selection process is for a project where drilling has defined sufficient geologic reserves, but little or no underground development has been done. Since each deposit has its own characteristic geanetry/grade distribution, and rock mechanics properties, mining method selection should be at least a two-stage process. In Stage 1, the deposit is described in terms of geometry, grade distribution, and rock mechanics properties. Using these parameters, the mining methods can be ranked to determine which are most applicable; they can then be considered in general terms of mining and capitalization cost, mining rate, type and availability of personnel, environmental concerns, and other site-specific considerations. In Stage 2, the most likely mining methods are costed out, based on a general mine plan. Mining and capitalization costs are used to determine a cut-off grade fran which a minable reserve can be calculated; economic comparisons can then be made to determine the optimum mining method and economic feasibility. During the mine planning phase of Stage 2, rock mechanics information would be used to provide realistic estimates of underground opening size, amount of support, orientation of openings, and caving characteristics, and open pit slope angles. If ground control or operational problems should be encountered with the methods being considered, modifications could be made. Although planning on paper extends start-up time, it is cheaper to err on paper than to find the error after mining has begun. METHOD SELECTION - STAGE 1 The main purpose of Stage 1 is to select those mining methods which should be considered in greater detail. The simplest way to do this is by defining those characteristics required for each mining method and then determining whether the characteristics of the deposit are suitable. However, no one mining method is so restrictive that it can be used for only one set of characteristics, as indicated by the classification system proposed by Boshkov and Wright (1973). In the mining method selection proposed, geometry, grade distribution, and rock mechanics characteristics are ranked according to their acceptability for ten general mining methods.

Jan 1, 1981

R.. B. T. KILIANI, New York, N. Y.-I do not care to discuss Mr. Taggart's paper in the light of theory, as that has been very well done by Prof. Bell,1 but I should like to criticize some of his conclusions, in the light of actual operating practice at plants all over the country. 1. Mr. Taggart's first conclusion is that in crushing average ore, the character of the gangue has little effect on the efficiency of the mill. This, I believe, is not in accordance with the usual practice, since in crushing a hard ore the capacity will be much reduced below what it would be with a softer ore, while the power consumed will be practically independent of the character of the ore, being proportional only, to the load of ore and balls in the mill. 2. Mr. Taggart's second criticism is that the Hardinge mill is not suitable for grinding soft, tough material. In answer to this I might mention that the mill is being used for grinding tough, dnctile material, such as metallic aluminum, and also for grinding licorice root. 3. He says that the ball-mill works more efficiently on material of intermediate size, say 1/2 to 3/4 in., than on either coarser or finer feed.. This is true as to coarser feed. For the most efficient work, I believe that a ball-mill should be fed with material not coarser than 1 1/2 in.; it' will handle material up to 3 and even 4 in., but the reduction from 3 or 4 in. to 1 1/2 in. can be done much more cheaply and efficiently by rolls or disk crushers than in the ball-mill. 4. As to Mr. Taggart's fourth conclusion, that a greater ratio of reduction can be expected with feed of an intermediate size than with a coarse feed, I have not enough information to express an opinion. 5. His next conclusion is that steel balls are much more efficient crushing media than pebbles. Steel balls are undoubtedly more efficient for crushing coarse feed. On fine material they are also more efficient as to tons per horsepower crushed to 10-mesh, but on fine material I think it will be found that flint pebbles are cheaper than cast-iron balls, per ton of ore, although there will be a saving in power per ton by using cast iron instead of flint. The increased cost of crushing with cast iron will be due to the higher cost of iron at the present time. 6. Mr. Taggart's sixth conclusion coincides with present practice, that steel balls will grind as fine or finer than pebbles when working on the same feed.

Jan 1, 1918

By L. Adler

Some estimate of the geologic pressures existine at the site of a proposed underground opening is essential for its economic design and construction. Regardless of the size of such an opening, drill hole, or mine stope, these primitive stresses need evaluation; at present a number of techniques are available for this purpose. However, a new method of analysind stresses is proposed in this paper. Some estimate of the geologic pressures existing at the site of a proposed underground opening is essential for its economic design and construction. Regardless of the size of such an opening, drill hole or mine stope, these primitive stresses need evaluation. At present a number of techniques are available for this purpose, and another one is to be proposed. These may be grouped into three general methods: 1) precedent, 2) instrumentation, and 3) theoretical analysis. The first two are covered in the literature where their advantages, as well as limitations, are discussed.'9' Generally a theoretical approach combines structural geology with engineering mechanics. The former deals with the geodynamic causes of residual stresses (stresses not related to overburden weight) and presents interesting, but controversial, views.'" A general and useful conclusion, however, can be drawn - vertical residual stresses are much less prevalent than horizontal. However, if for some reason, the values and effects of horizontal pressures were better known to engineers the following analysis

Jan 1, 1962

By E. G. Leonardon

THE object of this paper is to describe briefly the practical results obtained in several problems of civil engineering by resistivity measurements of the underground. It is intended for the mining engineer, as well as for the construction engineer; the stratigraphical problems discussed are general and frequently are encountered in mining exploration. Resistivity measurements have been used in mining and oil exploration for a number of years.1 Their introduction in the field of civil engineering, on the contrary, is rather recent. It was applied for the first time in the spring of 1928 near Littleton, N. H., in the survey of two dam sites for the New England Power Assn .2 Since then, the geophysical firm with which the author is connected has had an opportunity to develop this field of activity, and more than 20 investigations at dam and tunnel sites have been carried out in the United States and Canada. A part of this work has been verified by underground or drilling exploration. This paper deals with but a few of the results, which we are permitted to make public now. The theoretical and technical sides of the processes employed will not be discussed; they have already been described in various technical. .publications. A few general points will be mentioned, to make clear the practical examples given.

Jan 1, 1931

By R. V. Ramani, Robert Stefanko

The more stringent ventilation requirements of the 1969 Act have created a greater need for improved network analyses. More air is required at the last open crosscut (9000 cfm) and for the first time a minimum quantity is specified for the face (3000 cfm). Severe restrictions are placed on both belt and track haulage, and the intake air cannot contain more than 2 mg per cu m of respirable dust, to be reduced to 1 mg later. Larger tonnage and longer life mines are the trend today, necessitating multiple fans and shafts. Yet relatively little engineering goes into designing the mine ventilation system. In this paper a ventilation system is designed for a typical Pittsburgh block system, manual calculations are made and then checked by a computer solution. The computer is the ideal tool to try out proposed changes on paper to insure that the entire mine is properly ventilated and no costly adjustments need be made by dumping air. While it is theoretically possible to solve complex ventilation network problems by hand, it is not practical to do so because of the tremendous man-hours required and the many opportunities for errors. Thus the digital computer is indispensible to the ventilation engineer and newer improved ventilation programs are being developed to more realistically model mine ventilation networks. Suggested ventilation changes to comply with the new regulations are also critically evaluated.

Jan 1, 1973

By K. E. Starling

Phase equilibria data were used to develop an equation-of-state correlation for complex hydrocarbon mixtures, thereby circumventing difficulties associated with use of pressure-volume-temperature data. Equilibrium phase data for two condensate reservoir fluids were used to determine equation-of-state parameters for hydrocarbons as heavy as C22H46 in a modified form of the Benedict-Webb-Rubin equation of state. Comparative tests of K-values from the resultant correlation were made with data for condensate reservoir, separator and gas plant absorber mixtures. Generally, for temperatures above OF and computed liquid densities below 0.55 Ib-mole/cu ft, the modified BIVR equation predicted K-values in close agreement with the experimental data. INTRODUCTION Accurate predictions of thermodynamic behavior for complex hydrocarbon mixtures are necessary for many calculations in the petroleum industry. Because of the relatively high cost of extensive experimental data, many correlations for prediction of phase behavior have been developed. Some of these, such as the correlation of K-values presented in the NGAA Equilibrium Ratio Data Book, are totally empirical.l Others, such as the Benedict-Webb-Rubin (BWR) equation-of-state method, are semitheoretical.2-4 Unfortunately, published correlation methods often do not accurately predict the phase behavior of complex hydrocarbon mixtures, principally because of inadequate representation of the effects of components heavier than decane. This paper presents a new approach to this problem in which basic equation-of-state relations including heavy hydrocarbon effects are applied. Equilibrium phase data for two condensate reservoir fluids containing hydrocarbons as heavy as C22H46 are used to correlate component K-values. The BWR equation was chosen as the prototype equation of state for this study because of its proven capability for accurately predicting phase behavior and thermodynamic properties of light - hydrocarbon mixtures? Research was directed toward development of BWR parameters for the heavy hydrocarbons and modifications of the mathematical form of the BWR equation for application to complex hydrocarbon mixtures. The new equation-of-state approach presented differs considerably from previous methods in that phase equilibria rather than PVT data are used for determination of equation-of-state parameters. It is an explicit approach since the parameters are determined directly from mixture data. As such, it does not encounter problems inherent in the implicit method used by Benedict, Webb and Rubin 2-4 and numerous other investigators—one in which mixture parameters were postulated to be functions of the pure component parameters. The pure component BWR parameters, in turn, were determined from experimental PVT data. This method has been limited to mixtures containing components lighter than decane because of lack of vapor phase PVT data. Studies have been reported in which BWR parameters have been determined explicitly from PVT data for binary mixtures.6-8 However, since small concentrations of heavier components have only a minor effect on PVT behavior, it is doubtful that these explicit methods would yield useful results for condensate systems. Ellington and Eakin9 have shown that the accuracy of K-values predicted by an equation of state developed from mixture PVT data probably would be more than an order of magnitude lower than the accuracy of the PVT data. On the other hand, an equation of state utilizing parameters developed from phase equilibria data should predict K-values with accuracy comparable to the accuracy of the experimental phase compositions. This work applies this explicit approach with the objective of improving hydrocarbon mixture phase behavior predictions. Results are evaluated by comparing predicted and experimental K-values at reservoir, separator and gas plant

Jan 1, 1967

By Jacques B. Wertz

Among the parameters to be considered in the continuous search for new base-metal deposits, there often is a stratigraphic controlling factor that seems instrumental in the localization of ore. In British Columbia, for instance, the Upper Triassic as well as Lower Jurassic volcanics mixed with sediments are a useful indication in the search for copper while, in some parts of Australia, rhyolite bodies seem to be the favorable indicator, and this always within the geosynclinal environment. In Arizona, this stratigraphic factor becomes highly significant and it will be shown here that a large number of ore deposits are to be located around the flanks of ancient calcareous basins or depressions, preferentially corresponding to a certain optimum thickness as revealed by isopachs. The Martin limestone, of Devonian age, is already known for its basal O'Carroll bed which coincides with mineralization at places, and this is a relatively minor control. However, several limestone basins outlined by isopachs are in reality of greater importance as they localize mining districts. Indeed, most mines are found to coincide with a specific thickness of limestone while occurring simultaneously close to major, regional fracture intersections. The regional fractures in question were interpolated and extrapolated from known, important fault expressions, integrating quite well with the existing geology and further confirmed by minor criteria such as contacts, igneous plugs, axes of elongation of batholiths, dikes, etc. Although elements of subjectivity remain, this grid of fractures can be used quite successfully as a working hypothesis in the search for ore. Results of the present study which superposes major structural

Jan 1, 1971

By Reichmuth, Donald R.

Most brittle solids are relatively weak in tension and this weakness can be very significant in determining their performance in structures and excavations. Consequently, accurate knowledge of the tensile strength of brittle materials has long been recognized as important. In the past, measurements of the tensile strength of materials such as concrete, ceramics, and particularly rock have been hindered by problems encountered in fabricating test specimens and in accurately loading them. These difficulties have resulted in a scarcity of published tensile strength data. This can be readily seen in tabulations such as Wuerker's "Annotated Tables of Strength and Elastic Properties of Rocks.

Jan 1, 1968

By Roswell H. Johnson, W. E. Bernard

To know the rate of declinc of oil wells is very important, yet ordinarily we are prevented from getting this rate because the oil from several wells is put into one or a few tanks as soon as the wells have been connected to the power. The object of doing this is economy of tanks, pipes, labor, and accounting. But we are making a great sacrifice for this small economy. The advantages of the individual records are that we would know better: 1. When the well has ceased to be profitable. 2. When a well has gotten into bad condition. 3. The real record of the yield per acre and the rate of decline of the wells. The lease total is too mixed as to age of the wells for existing records to have much significance. To obtain such individual well records and more accurate logs are the great desiderata of satisfactory management of oil properties. 4. Which wells show the slowest decline—information which is valuable in locating new wells or purchasing adjoining leases. The truth of this statement is evident, when we reflect upon the large number of purchases of producing property. Intelligent appraisal is of the utmost advantage and it is impossible without individual well-pro-

Jan 1, 1918

INTRODUCTION TO MINERAL INVENTORY The first explanations to be made must answer the questions: What is a mineral inventory, and how is a mineral inventory different from an ore reserve? The term mineral inventory is a relatively new designation-born of the computer age and grown to common usage with the development of computer techniques for extending drill-hole sample values to regularly gridded data blocks representing in situ mineral values. The term has been generally accepted by geologists and engineers because it has a precise meaning which avoids many of the ambiguities of ore reserve. A mineral inventory is an estimated inventory of mineral in place and is usually achieved by dividing the deposit into regularly spaced gridded blocks to which are assigned estimated values using various extension techniques. A mineral inventory makes no presumptions about the mineability of the blocks or their cutoff grade. Such parameters are implied with the use of the term ore reserve. Ore has a specific definition (see Chapter 1) and ore reserve must reflect that definition and thus has economic and mining constraints. An ore reserve will be different under different economic and mining conditions and is subject to reclassification by many factors. The term mineral inventory avoids all such ambiguities. A mineral inventory estimate may be good or poor according to how much is known about the deposit, how extensively it has been sampled, and what techniques have been employed to assign estimated grade to the blocks. Such an inventory, however, does not change with time, economic conditions, or mining technology, but only with new and better data and methods. Thus, the mineral inventory is an excellent designation for describing mineral value distribution within a deposit's geological setting. The techniques for assigning values and tonnage to mineral blocks or panels are the subjects of this chapter. Whether a summation of the blocks be called a mineral inventory or mineral reserve is not important. Many conventional methods for computing reserves of minerals refer to the methods in terms of ore reserve calculations. OBJECTIVES OF MINERAL INVENTORY OR RESERVES Mineral inventories are computed for the purpose of determining the quantity, the quality or value, and the spatial distribution of potentially economic minerals within the earth. Such computations are made at all stages in the life of a mineral extraction process, from the early exploration phase to the final year in the life of a mine. To quote Popoff (1966, p. 2), "They are the most responsible and irreplaceable tasks in the valuation of a mineral deposit. Efficiency in extraction and productiveness is impossible without accurate reserve computations." The accuracy of estimate required for each of the three parameters of quantity, value, and location is dependent upon the objective for which the reserve estimate is being made. Again quoting Popoff (1966, p. 2): Reserves are computed to determine the extent of exploration and development; distribution of values; annual output; probable and possible productive life of the mine; method of extraction and plan design; improvements in extraction, treatment, and processing; and requirements for capital, equipment, labor, power, and materials. Such computations are used to assist development

Jan 1, 1980

By Rex E. Cheek, Donald E. Menzie

The fluid mapper, a model relatively new to the petroleum industry, was used to study the effect of various mobility ratios on the areal sweepout efficiency for two typical spacing patterns. The experiments indicated the areal sweepout for the five-spot pattern varied from 51.8 per cent at a mobility ratio of 0.093 to 89.1 per cent for a ratio of 24.4. In the direct line-drive pattern, the areal sweepout varied from 58.7 per cent at a mobility ratio of 0.089 to 92.0 per cent at a ratio of 24.8. The fluid mapper may prove useful to determine quickly the effective areal sweepout for any well spacing. INTRODUCTION The effect of the mobility ratio on the areal sweepout efficiency during primary depletion of a water drive reservoir and during secondary recovery operations has recently become more widely recognized The mobility ratio, M, is defined as: _ kjp (displaced fluid) k/u (displacing fluid) where k = effective permeability u = viscosity When the displacing fluid is miscible with the displaced fluid, the permeabilities are equal and the mobility ratio may be expressed as a ratio of viscosities: u (displacing fluid) u (displaced fluid) The mathematical analysis for calculating the areal sweepout efficiency with mobility ratio other than unity is quite tedious.5,11 An experimental method by using a potentiometric model2 in a step-wise manner and in using an X-ray shadowgraph model3,12 with continuous fluid flow has been published. Several types of models have been used to study oil and gas reservoir performance. These models may be classified as physical, electrolytic, potentiometric, X-ray shadowgraph, and fluid mapper. The X-ray shadowgraph and fluid mapper are models relatively new to petroleum engineering and have not been used extensively for specific applications. The theory of the fluid mapper indicates it may be adapted to a study of areal sweepout efficiencies for various mobility ratios as well as other complex problems in petroleum engineering. The use of the model and results obtained when using displacing and displaced fluids of equal densities but different viscosities are discussed. FLUID MAPPER DEVELOPMENT H. S. Hele-ShawV eveloped a fluid mapper model based on the hydrodynamic theory. This theory is that in the steady flow of a viscous fluid between horizontal parallel plates spaced a very small distance apart, the effect of viscous shear is of such magnitude in the vertical plane that the motion in the horizontal plane is practically undisbrted streamline flow. Techniques developed by Hele-Shaw were not expanded and no additional developments in fluid mapper models were forthcoming until A. D. Moore, University of Michigan, published a series of papers starting in 1949, which describe the construction of a flexible and inexpensive model'h nd the fluid mapper technique for the solution of certain problems.' The essential components of the fluid mapper as developed by Moore are::.ln 1. A base slab. made of dental stone (calcium sulphate and water). which is shaped to represent the prototype. 2. Plate glass slightly larger than the slab and spaced

Jan 1, 1956

By Charles W. Merrill

IF we follow the threads of the mining problems, upon which I have touched, we find them all leading to one great fundamental desideratum. The people of this State, of this Nation, and of this world must be brought to a better understanding of the basic nature of our industry-must be made more mineral-minded. It is my belief 'that there is not a man present among this earnest gathering of those interested in the mining industry, who has not a deep-seated and heartfelt desire that the existing unprecedented welfare and prosperity of the whole mass of American people be maintained not merely through our own generation but through the generations of our children and their children. In the decades to come there can be no question of the keenness of the foreign competition which we are doomed to meet, and in this great international contest that Nation which has the best balanced program of development and that broadness of vision in its governmental direction, which recognizes the necessity of a sympathetic attitude toward the upbuilding of such a broad pro- gram will be the Nation which will maintain and pre- serve that welfare of all of its people.

Jan 1, 1929