Search Documents

By A. T. Churchman

The deformation modes of rhenium have been identified as those typical of the hexagonal metals, titanium, zirconium, and beryllium whose c/a ratios, in common with rhenium, are less than ideal for close packing. Slip is observed on (1010), (1011), and (0001) planes and twinning on (1121), (1122), and (1012) planes. The very high rate of work hardening is believed to be associated with intersecting partial dislocations on two (1010) systems which can combine to form sessile barriers. If the stacking fault energy is low, as postulated by Seeger, these barriers should be strong and not easily bypassed by cross slipping. Such an explanation could also account for the very small temperature dependence of the yield stress which was observed. RHENIUM is interesting scientifically as a member of the group of high melting point hexagonal metals: titanium, beryllium, and zirconium with a c/a ratio less than that for ideal close packing. Unlike them, however, it work hardens at a very high rate. This rate is greater and continues to a much higher degree of deformation than for nickel, normally considered to have a high rate of work hardening. This paper presents experimental observations on the modes of deformation of rhenium and, by comparison with other hexagonal metals, some speculation on the cause of the high work hardening. MATERIALS Johnson, Matthey rhenium powder of both 99.9 pct and 99.5 pct purity, see Table I, was compacted at 10 tons per sq in., part sintered at 1350°C in vacuo, and finally arc melted in a "gettered" argon atmosphere arc furnace to produce small buttons. Little difference was observed in the as-cast hardness or working down behavior of the two purities suggesting that either silicon and potassium do not have a significant effect on the working properties of rhenium or they were lost during arc melting. SPECIMEN PREPARATION The cast structure was broken up by cold-rolling with inter-stage annealing at 1600o or 1800°C in a vacuum high-frequency furnace using a tungsten susceptor. Strip for tensile testing was taken from two thicknesses of material 0.011 and 0.064 in. The former with intermediate anneals at 1800°C had a grain size of 900 grains per sq mm, while the latter with inter-stage annealing at 1600°C had a grain size of 3600 grains per sq mm. A coarse grain size was obtained by secondary recrystallization in a half button cold-worked by 30 pct reduction. Annealing times of from half an hour to several hours at 2200° to 2600°C in a "gettered" argon atmosphere arc furnace1 resulted in grains of up to 2 mm diam.

Jan 1, 1961

By A. E. Dwight, P. A. Beck

A search was made for ordered phases of AB3 composition in various combinations of Ti- and V-group elements with CO-and Ni-group elements. Three new TiNi3-type phases ZrPd3, HfPd3, and HfPt3 were found. In addition, twelve new Cu3Au-type phases TiRh3, Tilr3, ZrRh3, Zrlr3, HfRh3, Hflr3, VRh3, VIr3, CbRh3, Cblr3, TaRh3, and TaIr3 were also found. The lattice contraction for all three structures considered increases with increasing relative size of the A atom, suggesting that it is mostly the A atom that cont~acts. It was noted that, for the same radius ratio the lattice contraction is larger when the A atom is Ti than if it is Cb OY Ta. It is well known that elements or disordered solid solutions, which have structures with spherical close-packing, may be described in terms of various stacking schemes of close-packed layers. Stacking of the type abab corresponds to the hexagonal close-packed structure, and stacking of the type abcabc corresponds to the face-centered-cubic structure. In binary alloys of the first, second, and third long period transition elements various AB3 phases occur with close-packed ordered structures. It was observed that these ordered structures also may be described by suitable stacking of close-packed ordered layers, Fig. 1, as first shown by Laves and Wallbaum for TiNi3.' It is clear that the units of translation in such a close-packed layer consist of four atoms, one of which (black circle) is atom A and the three others (empty circles) are atoms B. Because of the alternation of A and B atoms in every second row of each layer, the unit-cell dimension in the layer is equal to the sum of the diameters of atoms A and B: a0 = 2(rA + rB). Stacking of such layers in the sequence abab results in a hexagonal close-packed structure of the MgCd, type. The unit-cell dimension in the basal plane is approximately double of that for the disordered hexagonal close-packed structure, but in the direction of the hexagonal axis it is about the same, so that 2co/uo = 1.63 in case of spherical close-packing. Ordered hexagonal close-packed structures of this type were found to occur in MoCo3,2 WCo3,, and UPt, .4 When the ordered layers shown in Fig. 1 are stacked according to the scheme abcabc, the resulting ordered structure is of the AuCu, type (cubic). Structures of this type were found to occur in TiPt3,5 CrPt,,' CrIr,,' and URu, .4 Finally, the stacking scheme abacabac of the same ordered layers results in a hexagonal close-packed structure of the TiNi3 type.' In this case, the unit-cell dimension is doubled not only in the basal plane, but also in the direction of the hexagonal axis, so that co/ao = 1.63. Structures of this type were found to occur also in TiPd3,5 ZrPt,," and UPd,.4

Jan 1, 1960

By Nicholas J. Grant, Henry Epstein, John Chipman

FOR many years steel producers have been concerned with the presence of hydrogen in steel. Hydrogen dissolved in excess of its solid solubility at the melting point may cause bleeding and gross unsoundness in ingots and castings. In fully-killed steels the hydrogen content which results in these difficulties varies with the alloy content1 and may range from 6 to 12 ppm.* It is also recognized that of heat treatment diminishes rapidly as the size of the part to be treated increases. The time required to remove a specified fraction of the hydrogen present increases as the square of the diameter of the section, making the treatment of large- sizes impractical. In order to prevent bleeding and gross unsound-ness due to hydrogen, and in view of the inadequacy of corrective heat treatment alone to provide optimum properties when hydrogen is present in large sections, efforts to limit the hydrogen content must be taken while the steel is still liquid. The main subject of this paper is a discussion of the factors affecting the hydrogen content of liquid steel in acid and basic open hearth, and basic electric two-slag furnace processing. Literature Survey Because many of the results and observations reported in the literature have a direct bearing on the results obtained in the present research and form part of the basis for conclusions reached, a brief summary of the findings is necessary. Methods for experimental investigation of hydrogen in liquid steel are comparatively new. The first attempts to estimate the hydrogen content of the open hearth bath were by Kalling and Rudberg,6 who devised a method for collecting gases evolved from the boiling bath of a basic open hearth furnace. They found that the gas during the boil generally contained 2 to 3 pct H2. From this and Sieverts'

Jan 1, 1958

By Howard S. Bryant

The year 1928 has recently.passed from the picture and it is at this time that the various divisions of the oil industry are giving thought to plans for the present year. The outstanding characteristic of the industry in 1928 was the successful curtailment of oil production to the market's needs. It has been thought advisable to look ahead and endeavor to anticipate the oil demand for the coming year, and thus determine the volume of oil that can be safely produced without causing major additions to surface stocks. The year has been one of smaller additions to stocks than in 1927, a record demand for oil products, and a further developed spirit of cooperation among oil producers, as well as various other achievements. It is well to pause and take stock of ourselves. Present Status of Crude Oil Supply and Demand The total daily new supply of oil is at this time1 about 2,960,000 bbl. per day, made up of 2,585,000 bbl. domestic crude production, 125,000 bbl. casinghead gasoline, and 250,000 bbl. of imports. With the present low consumption, due to the falling off in the winter season demand, it is estimated that about 150,000 bbl. a day are now being run to storage, and that the first three months in 1929 will see large-sized additions to storage. Consumption plus exports of oil have increased at a regular rate from year to year, and although oil production in 1928 passed the 1,000,000,-000 bbl. mark for the second time in the history of the United States, with a production of 25,000,000 bbl. more than in 1927, only 30,000,000 bbl. were added to storage during 1928. This is compared to an addition of 65,500,000 bbl. in 1927.

Jan 1, 1929

By W. C. Elli, M. E. Fine

YOUNG'S modulus of elasticity in metals ordinarily decreases with rising temperature. The range of the thermoelastic coefficient at room tem- 1/E dE/dT perature (temperature coefficient of modulus, is illustrated1 by the values for tungsten and hard-drawn aluminum, —95 and —1220x10-6 eg C-1. However, a nearly zero thermoelastic coefficient is observed in some ferromagnetic alloys over a limited temperature range. In these alloys, as the temperature is raised, an increase in modulus arising from loss of ferromagnetism compensates the normal decrease. Iron-nickel alloys containing 36 to 52 pct Ni behave in this manner. In the present investiga- tion, the dependence of the modulus and thermo-elastic coefficient on cold working and annealing were studied in iron-nickel alloys in this range of nickel. Although these alloys, when fully annealed, have a coefficient near zero over a very small temperature interval, the temperature range of low coefficient can be extended greatly by straining and then stress-relief annealing. The modulus of face-centered cubic iron-nickel alloys annealed at 1000°C does not vary linearly with composition at room temperature but, as shown by the solid line of fig. 1, from Koster,' is minimum at 40 pct Ni and maximum at 87 pct Ni. The modulus increases with applied magnetic field but retains the minimum near 40 pct Ni. Schematic change of modulus with temperature for three compositions is shown in fig. 2.'. ' With increasing temperature, the slope becomes less negative, goes through zero (temperature of minimum modulus for the alloy), becomes positive, and resumes its normal negative value above the Curie

Jan 1, 1951

By H. D. Kessler, M. Hansen, R. J. Van Thyne

The phase diagram of the titanium-rich portion of the system Ti-Cr-Fe to 70 pct Ti was established by means of isothermal sections at 900°, 800°, 750°, 700°, 650°, 600°, and 550°C, using arc-cast alloys. An isotherm at 800°C was determined for the section bounded by Ti, TiFe2, and TiCr2. Micrographic analysis was employed as the principal method of investigation, supplemented by X-ray diffraction and incipient melting studies. A ternary eutectoid, ß ? a+ TiCr2 + TiFe, occurs at approximately 8 wt pct Cr, 13 wt pct Fe, and about 540°C. AMONG the first titanium-base alloys in commercial production were the Ti-Cr-Fe alloys. For this reason, the Materials Laboratory, Wright Air Development Center, sponsored an investigation of the system. No information on the constitution of the titanium-rich corner was available. Vogel and Wenderott studied titanium-poor ternary alloys.' As part of this program, the binary systems Ti-Cr and Ti-Fe have been determined previously by the authors.' Other investigators have also studied the binary systems Ti-Cr,3-7' Ti-Fe.³,8-10 Both of the binary systems are characterized by the eutectoid decomposition of the ß phase. Most of the effort of the present work has been concentrated on the titanium-rich corner with compositions of less than 30 pct total chromium and iron content. The determination of isothermal sections was the experimental approach used to obtain the ternary phase diagram. Vertical sections were used to check the consistency of the isothermal sections. While this investigation was in progress, a study of the Ti-Mo-Cr system at Armour Research Foundation disclosed the existence of a high temperature modification of TiCr2 above 1300 °C.11 This allotrope has a hexagonal structure of the MgZn2 type, iso-morphous with TiFe2, whereas the low temperature modification of TiCr2 is cubic," of the MgCu2 type. The existence of allotropy in TiCr2 of course means a more complicated set of phase relationships in this general region than if the phase were monomorphic, as was first assumed. Additional studies were made late in the investigation in order to clarify the part that the hexagonal TiCr2 phase plays in the ternary phase relationships. These will be discussed in a separate section. Because they are of greatest practical significance, the phase relationships in the titanium-rich corner will be presented first, omitting the equilibria involving the hexagonal modification of TiCr2 in an effort to simplify the presentation somewhat. Experimental Procedure Materials: The titanium used in the preparation of the alloys was iodide crystal bar (99.9 pct pure) produced by the New Jersey Zinc Co. High purity chromium and iron were obtained from the National Research Corp. Table I gives the analyses of these materials. Melting Practice: Over 100 alloy ingots weighing 10 to 20 g were melted in a nonconsumable electrode arc-melting furnace. As the techniques are identical to those reported previously,12,13 they will not be detailed here. The ingots were melted in the cavity of a copper melting block insert under a slight positive pressure of helium. No measurable hardness

Jan 1, 1954

By Franklin G. Pardee

WARTIME depletion of the reserves of iron ore in the Lake Superior region of the grade and character now being shipped down the Lakes was serious. The time has come to take stock of the resources that remain in order to plan our future program of supply for our blast furnaces and protect, as far as possible. the tremendous investment made in the Lake Superior iron mining industry. Hugh M. Roberts and William H. Crago have estimated the reserves of the Lake Superior region in the United States at two billion long tons. These reserve figures are of direct-shipping ore and those concentrates produced by methods now in commercial use or those methods that may be expected in the near future. In their estimate they have assigned 392 million long tons to the Michigan ranges (all reserves in long tons) : 112 million tons for the Gogebic. 140 million tons for the Menominee, and 140 million tons for the Marquette.

Jan 1, 1948

By C. M. EYE

IN the spring of 1905 I was employed by Messrs. Bradley and Requa, under our fellow member, Thomas Cox, on the mill plans for the Nevada Consolidated, when an opportunity came to go to the Philippines to erect a small mill on the property of the Benguet Consolidated. This I accepted, expecting to be away eight months or so, but it was seven years before I got back. .I sailed in May, on the Coptic, having as room-mate as far as Kobe, A. E. Drucker, who was going out to Korea for the Oriental Consolidated. It was the first trans-ocean trip for either of us, and we had some rather unusual experiences. This was toward the close of the Russo-Japanese war and the Russian fleet was known to be on the way from Suez to Asiatic waters, but it was a matter of doubt whether they would risk a passage between Japan and the mainland, or take the longer but obviously safer route outside of Japan. The Coptic carried much contraband of war for Japan, so naturally did not care to meet this fleet. No definite word being available at Honolulu, we went to the Midway Islands, but the cable station there had very little information to offer, so we proceeded cautiously toward Japan. On the last afternoon out, we steamed due north at half speed for several hours, and finally sneaked into Yokohama at night, to learn that ' the Russian fleet had met the Japanese the day before and had been annihilated. We sailed over the spot in the Sea of Japan a week later, and when we got to Manila we found three of the Russian boats interned and being guarded by the monitor Monadnock and a cruiser. This was only a matter of form, as the Russians were only too glad to be there for the rest of the war, and the boats could not have gone far anyway, for they were literally shot to pieces. The Admiral's flagship had a hole within 3 ft. of the water line, for ward, through which a man could enter by stooping.

Jan 1, 1929

By J. J. Gilman

The data presented indicate that the critical shear stress and strain-hardening Thedatapresentedrate of a zinc monocrystal depend on the orientation of its slip direction with respect to its external boundaries. The tendency of a crystal to form deformation bands also depends on its shape. THE plastic behavior of pairs of zinc monocrystals in which both members of the respective pairs had the same orientation with respect to the longitudinal axis, but each had different orientations with respect to their rectangular external shapes, were compared in this investigation. The purpose of the investigation was to see what influence the shape or surface of a zinc crystal has on its mechanical properties. In a previous investigation of triangular zinc monocrystals,1 anomalous axial twisting was observed which seemed to be related to the triangular shape of the crystals. Wolff,' in 400°C tensile tests of rectangular rock-salt crystals bounded by cubic cleavage planes, found that, of the four equivalent slip systems, the two with the "shorter" slip directions yielded and produced slip lines at lower stresses than the other two. This observation and the work of Dommerich³ as formulated by Smekal4 as a "new slip condition" for rock-salt: "among two or more slip systems permitted by the shear stress law, with reference to the formation of visible slip lines by large individual glides, that slip system is preferred which has the shortest effective slip direction." More recently, Wu and Smoluchowski5 reported essentially the same effect for ribbon-like (20x2x0.2 mm) aluminum crystals at room temperature. Experimental Chemically pure zinc (99.999 pct Zn), purchased from the New Jersey Zinc Co., was the raw material. Glass envelopes, containing graphite molds and zinc, were evacuated while hot enough to outgas the graphite but not melt the zinc. At a vacuum of about 0.2 micron the envelopes were sealed off and then lowered through a furnace at 1 in. per hr so as to melt and resolidify the zinc and produce mono-crystals. One-half of one of the molds is shown in Fig. la. Each mold consisted of four pieces from a cylindrical graphite rod that was split longitudinally and transversely at its midpoints. Rectangular milled grooves 0.050 in. deep and % in. wide formed the mold cavity when the split halves were assembled with twisted wires. Fig. lb shows the specimen shape obtained when the top and bottom mold-halves were rotated 90" with respect to each other. Good fits prevented leakage and excess zinc was necessary to provide enough liquid head to fill the mold completely. In removing soft crystals from the molds it was impossible to avoid small amounts of bending. However, manipulations were carried out whenever possible with the crystals protected by grooved brass blocks. All specimens were annealed prior to testing. From the top and bottom sections of each crystal, X-ray specimens and tensile specimens 7 to 8 cm long were sawed. The tensile specimens were annealed inside evacuated tubes for 1 hr at 375°C. Next the crystals were cleaned and polished by 2-min dips in a solution of 22 pct chromic acid, 74 pct water, 2.5 pct sulphuric acid, and 1.5 pct glacial acetic acid.' Cleaning was followed by a 10-sec dip in a 10 pct caustic solution, then washed in water and alcohol, and dried. This treatment results in a bright surface covered by an invisible oxide film. The testing grips were a slotted type with set screws and were supported in a V-block during the mounting operations in order to avoid bending the crystals. A schematic diagram of the recording tensile-testing machine is shown in Fig. 2. The machine has been described elsewhere.' The head speed was 0.3 mm per sec for all tests. The crystal orientations were determined by the Greninger X-ray back-reflection method with an estimated accuracy of 1. Description of Crystal Geometry A schematic picture of a rectangular zinc mono-crystal is shown in Fig. 3. ABD designates the front edge of a basal plane (0001) of the crystal, the only active slip plane for zinc at room temperature. Of the three possible (2110) slip directions, the active one is indicated by an arrow. Cartesian coordinates are taken parallel to the specimen edges. The normal, n, to the basal plane (n is parallel to the hexagonal axis) has the direction cosines a, ß and ?. X0 = 90 — y is the angle between the longitudinal axis and

Jan 1, 1954

By H. N. Mills

The glass industry is a major user of many industrial minerals in the manufacture of its product. It is the intent of this chapter to: (1) acquaint the reader with the glass industry by including a few production statistics, and (2) cover the various aspects of the major raw materials used to make glass. The matter of glass compositions, properties, and batches is considered beyond the scope of this chapter which deals only with raw materials. For more details on the particular minerals and rocks used in glassmaking, the reader is referred to chapters in the commodity section of this book. Glass Industry Statistics Glass manufacture in the United States can be divided into three major product classifications as follows: 1) Glass containers 2) Pressed and blown glass 3) Flat glass Glass containers include bottles and jars for the packaging of food and beverages, as well as drugs, chemicals, and cosmetics. Pressed and blown glass includes table, kitchen, art and novelty ware, lighting and electronic glassware, and fiber glass. Flat glass covers sheet or window glass, plate, laminated, and safety glass. The US Department of Commerce statistics, as recorded in the 1977 Census of Manufacturers, compares the dollar value of glass shipments for each product category. These statistics are shown in Table 1 (Anon., 1980) and are self-explanatory. A comparison of the tonnage output in each product classification is difficult, as production data is reported in "gross" for glass containers, "pounds" for fiber glass, "pieces" for glassware, [ ] and "square feet" for flat glass. In the case of glass containers, an average "pounds per gross" factor can be applied to the total production figures reported in thousands of gross in Bureau of Census industrial reports. Table 2 presents the calculated annual production tonnage for glass containers for the years 1974-1979. Except for 1979, there was a yearly increase in production. The tonnage figures of Table 2 are further influenced by decreasing weight per gross which has occurred in the glass container industry since 1975. This reflects the gradual shift to lighter weight containers for beverages. Other segments of the glass industry have experienced growth, but the figures in tons are not published information. Fiber glass growth has been influenced by the heavy demand for insulation as part of energy conservation efforts on a national basis. The production of flat glass by the float process has continued to grow with several new plants entering production. All portions of the glass industry experienced the effects of the general economic decline of 1979-1980, but the outlook for the future is bright. Batch Materials For Glass Use Materials and Function Soda-lime-silica glass represents the largest proportion of glass manufactured for commercial use. It is produced by the fluxing and

Jan 1, 1983

By John T. Wizzard, R. P. Killmeyer, B. S. Gottfried

The Coal Preparation Branch of the Pittsburgh Energy Technology Center has developed a computer program to calculate the performance characteristics of coal washing devices. This program uses specific gravity analyses of the clean coal and refuse streams as input, and generates dependent and independent performance criteria for the washer. Partition curves are internally represented in a functional form by a Weibull function. Performance criteria generated by this computer program are compared to manually calculated performance criteria for air tables, Dynawhirlpools, Baum jigs, hydrocyclones, and dense medium cyclones. The comparisons show that the computer program gives results in close agreement with the hand- calculated values while greatly reducing the amount of time involved in performing the analyses.

Jan 1, 1983

For the year ending February, 1926 PRESIDENT J V W REYNDERS, District 0 NEW YORK, N Y PAST PRESIDENTS E P MATHEWSON, District 0 NEW YORK, N Y WILLIAM KELLY, District 5 IRON MOUNTAIN, MICH FIRST VICE-PRESIDENT E DEGOLYER, NEW YORK, N Y TREASURER , CHARLES F RAND, NEW YORK, N Y SECRETARY FREDERICK F SHARPLESS, NEW YORK, N Y

Jan 1, 1923

By C. J. McHargue, J. C. Ogle

Lightly deformed columbiun single crystals which contained only parallel hoins or purullel and intersecting trains were annealed at 1000' and 1600"C. No re-crystallizntion occurred in specimens hawing only parallel twins. Only noncoherent twin boundaries nzipated at 1000°C but both coherent and noncoherent ones moved al 1600°C. Recrystallization occurred within a few minutes at twin intersections at 1000°C. The orientation 01 the recrystallized grains differed front that of both the matrix and deformation twins, but could he derired by (110) and/or(112) rotations. ALTHOUGH twinning in metals has been extensively studied, there have been no definitive studies of the annealing behavior of crystals containing deformation twins. Some effects observed after annealing deformation twins have been summarized by Cahn1 and Hall2. Any or all of these phenomena are observed: 1) The twins may contract so that the sharp edges of the lens become blunted, and eventually the twin may disappear entirely. 2) The twins may balloon out at an edge, giving rise to a large grain having the same orientation as the twin. 3) The specimen may recrystallize; i.e., new grains are nucleated and grow at the expense of the twins and the crystal immediately adjoining the twin. Such grains have orientations which are not present before. Contraction has been observed in iron,3 titanium,3, 4 beryllium,5 zinc,8, 7 Fe-A1 alloy,' and uranium.9 Long anneals at high temperatures are required to have any appreciable effect in these metals and only thin twins are absorbed. Lens-shaped twins are absorbed from the edges: the thin, almost parallel-sided twins are usually punctured in several places and each piece contracts independently. Absorption is very gradual and no sudden cooperative jumps have been observed. The expansion of a twin into a larger grain of identical orientation is unusual, but such growth has been observed in iron,"'" zinc,6 and uranium." Crystals which have been deformed simultaneously by slip and twinning recrystallize first in the area adjacent to the twin. New grains appear faster where the twins intersect: but isolated twins, especially if thick, can also give rise to new grains. This type of recrystallization occurs in zinc.6, 7, 12, 13 and beryllium.14 Reed-Hill noted, in a single crystal of magnesium, the nucleation of a recrystallized grain at a twin intersection which had the same orientation as the second-order twin and which grew into the highly strained matrix.15 Short-time annealing has been reported to cause no change in the deformation twins in vanadium,16 columbium, 17, 18 tantalum,19 tungsten,'' and zinc.7 The purpose of this investigation was to note the effects of annealing on the coherent and noncoherent boundaries of deformation twins in columbium and to locate the nucleating sites for recrystallization. The orientation relationships, which the new recrystallized grains have with the parent crystal and the deformation twins, were also determined. EXPERIMENTAL PROCEDURE Single crystals of columbium were obtained by cutting large grains from electron-beam-melted buttons which contained 10 to 50 ppm C, 10 to 100 ppm O,, 1 to 10 ppm H2, and 10 to 15 ppm N2. The crystals were hand-ground and chemically polished until all grain boundaries were removed. The specimens were mounted in an epoxy resin and a face of each crystal was mechanically polished on a Syntron polisher using Linde A and then Linde B polishing compounds. After all faces were mechanically polished, the crystal was electrolytically polished to remove all distortion due to cutting and grinding. Laue photographs were taken of all faces of the crystals to determine the quality and orientation of each crystal. The crystals were compressed about 10 pct at -196 C in a specially constructed compression cage with an Instron tensile machine. Each crystal was separated from the top and bottom anvils by teflon films which acted as a lubricant. With the specimen crystal in position, the entire cage was cooled to -196°C by being submerged in a Dewar containing liquid nitrogen. The crystals were compressed at a rate of 0.02 in. per min and the load was recorded on a strip-chart recorder. After deformation the crystals were mechanically polished on 600-grit paper and Pellon cloth with Linde A and Linde B polishing compounds. The crystal faces were chemically polished and then etched. The twin planes were identified metallographically from an analysis of the twin traces on two surfaces. Annealing was carried out by placing each crystal in a columbium bucket made from the same electron-beam-melted material as the crystal itself and suspending the bucket by a tantalum wire in a quartz tube. After a vacuum of 10-7 Torr was attained, a furnace at 1000" or 1600 C was raised into position and the crystals held for various lengths of time. The crystals were repolished and etched after annealing to remove any surface contamination. Approximately 0.010 in. was removed during this process. The resulting surface was examined metallographically for microstructural changes due to annealing. A microbeam Laue camera mounted on a Hilger Micro-focus X-ray unit was used to determine the Orientstions of the recrystallized grains. This X-ray micro-beam camera had a 0.002-in.-diam collimator and incorporated the ideas of both and and chisWik21 and Cahn.22

Jan 1, 1967

For the year ending February, 1919 PRESIDENT SIDNEY J. JENNINGS NEW YORK, N. Y. PAST PRESIDENTS L. D. RICKETTS, NEW YORK, N. Y. PHILIP N. MOORE ST. Louis, Mo. FIRST VICE-PRESIDENT C. W. GOODALE, BUTTE, MONT. TREASURER GEORGE C. STONE, NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W. RAYMOND, NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 11, 1918

For the year ending February, 1918 PRESIDENT SIDNEY J. JENNINGS, NEW YORK, N. Y. PAST PRESIDENTS L. D: RICKETTS, ; . , . NEW YORK, N. Y. PHILIP N. MOORE, , ST. Louis, Mo FIRST VICE-PRESIDENT C. W. GOODALE, . . . . BUTTE, MONT. TREASURER GEORGE C. STONE NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W. RAYMOND,. NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 3, 1918

For the year ending February, 1919 PRESIDENT SIDNEY J. JENNINGS NEW YORK, N. Y. PAST PRESIDENTS L. D. RICKETTS NEW YORK, N. Y. PHILIP N. MOORE ST. Louis, Mo. FIRST VICE-PRESIDENT C. W. GOODALE BUTTE, MONT. TREASURER GEORGE C. STONE, NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W. RAYMOND, NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 9, 1918

By K. J. Brondyke, P. D. Hess

Two processes have been developed for improving the quality of molten-aluminum alloys before casting. The Filtration Process. which involves passing molten metal through a packed bed of granular filter material, is a rapid means of removing finely divided particles. It has the most potential in those instances where removal of inclusions is of primary importance. The Combination Fillration-Inert Gas Fluxing Process inuolzles introduction of an inert gas so that it will diffuse countercurrent to metal flow through the filter bed of granular material. Dissolved hydrogen is removed from the metal in addition to removal of finely divided particles. The Combination Process is most useful where both inclusion removal and attainment of conistently low-hydrogen-content metal are important. Metal treated by the Combination Process is of higher and more uniform quality than heretofore attainable with prolonged chlorine fluxing. Costs of the Combination Process can, for the most part, be offset by savings derived from high recoveries and increased production of superior-quality products. IMPROVEMENT in the quality of molten-aluminum alloys is secured generally through the use of some fluxing practice in a crucible, holding furnace, or ladle involving either gaseous or solid fluxing media. Typical fluxing agents may include the gases nitrogen, argon, or chlorine used either singly or as mixtures and the solids aluminum chloride or hexachloroethane. Regardless of the fluxing means used, the primary objectives are the adequate removal of both metallic and nonmetallic inclusions and reduction of hydrogen content to an acceptably low level. The ultimate goal is to produce ingots and cast products of high quality free from inclusions and porosity. The development of ultrasonics for measurement of internal quality, tightening of quality controls, and the application of the aluminum alloys to new or different commercial fields have been responsible for an ever increasing demand for improvement of quality of both cast and fabricated products. This demand for high quality has not been restricted to any single type of product. On the contrary, the demand encompasses about the entire variety of products including those for fabrication, those to be machined, buffed, or finished for decorative purposes, and those for critical applications where both surface and internal quality is of utmost importance. In many instances products acceptable in the 40's would now be scrapped as unacceptable by these higher present-day standards. With this ever increasing demand for higher quality, it became apparent at Alcoa that conventional means of melt treatment were inadequate in many instances and new approaches were necessary. Consequently the research program was intensified with attention focused on metal treatment during transfer in order to reduce the furnace processing time to a minimum in an effort to attain the desired results at a minimum of additional expense. As a result of this intensive research program which covered numerous variations and adaptations of conventional methods in addition to new methods of melt treatment, several new processes were developed, two of which will be described here. The first of these, a method of melt filtration, was patented in February, 1959.l The second process involving combination filtration—inert gas fluxing was patented in June, 1962. 2 Other melt-treatment processes developed during this period of investigation were patented as listed.3 FILTRATION PROCESS General Description. The Filtration Process, which involves passing molten metal through a packed bed of granular filter material, is a rapid method of effectively removing finely divided particles. It is an impingement-type filter; hence the size of the particles removed from the metal are considerably smaller than the interstices of the

Jan 1, 1964

By Paul A. Flinn, Jean-Marie Robert Genin

The MCssbauer effect was used to study the distribution of carbon in Fe-C alloys of high carbon content during room-temperature aging. In freshly formed rnartensite the carbon distribution is approximately random; carbon clustering occurs dun'ng aging. In the retained austete the carbon atoms are isolated, suggesting an efiective repulsion; and no rearrangement during room-temperature aging is evident. The kinetics of the carbon clustering in martensite has been studied in detail at 0" . 10". and 20°C. The time and temperature dependence observed is sinzilar to that reported for a variety of other aging effects, such as resistance change, hardness increase, and recovery of internal friction. The stabilization of the martensite kransformation also appears to be related to the clustering effect. DESPITE extensive efforts since the early days of Reaumur, the mechanism which provides the strengthening of steel remains controversial in many cases for several reasons: 1) The structure of as-quenched martensite is not well-determined. 2) Experimental methods capable of distinguishing between various hardening mechanisms are not well-developed. 3) The temperature of formation of many low-alloy martensites is so high that the martensite formed during quenching may be already tempered to some extent before any observation. Among all the hardening phenomena, the most puzzling one occurs at room temperature, where no structural changes have been detected by the usual methods of X-ray diffraction or electron microscopy. However, a new and more sensitive technique became available with the discovery of the MBssbauer effect. This effect makes possible the detection of changes in the local environment of iron atoms in solid solution. It has been extensively used in the study of substitutional alloy systems, for example, Fe-Al,1 Fe-Si,2,3 Fe-Rh,4 and Fe-Ni.5 Making use of the possibility of obtaining new structural information, we undertook an investigation of the aging of high-carbon Fe-C martensite to follow the structural changes involved in the aging at room temperature. Preliminary results6 showed that a clustering of the carbon atoms occurs with time. A systematic study of the kinetics of the process showed a striking similarity to the kinetics of stabilization of the marten-sitic transformation, thus suggesting further investigation of the relationship. EXPERIMENTAL TECHNIQUE To eliminate difficulties with the aging of martensite prior to the first experimental measurements, we needed an alloy with an M, temperature not above room temperature. Other investigators7 were misled by results obtained on alloys which transformed above room temperature and underwent structural changes prior to the first Mossbauer measurements. Winchell and cohen8 dealt with this difficulty by using a third element, nickel, to depress the MS below room temperature. The presence of nickel did not seriously interfere with hardness or resistivity measurements, but it would complicate the interpretation of the Mossbauer data by increasing the variety of iron environments. We chose, therefore, to obtain the necessary lowering of the M, simply by increasing the carbon content. After the first quench to room temperature, our specimens are retained austenite, which we later quench into liquid nitrogen. The martensitic transformation takes place suddenly, so that the as-quenched condition of the samples is retained, since the temperature is low enough to prevent any carbon diffusion. A Massbauer spectrum at 77°K can be taken and analyzed; after an appropriate up-quenching to the aging temperature, a new Mossbauer measurement at 77°K can be made. Fig. 1 shows a typical cycle of experiments. The samples were foils 25 p thick of high-purity

Jan 1, 1969

By WM. E. Mlligan

IN the last year, much information had become available as to the extent that zinc participated in the war effort. The importance of foreign zinc in this program had been indicated by Bateman (M&M April 1945) as of the order of 400,000 tons annually in zinc or contained zinc. Pehrson (M&M April 1945) reviewed the domestic ore-reserve situation with respect to most minerals and metals and showed the extent to which commercial zinc ores had become depleted in this country. This picture was further darkened by O.P.A. figures appearing in E.&M.J. July 1945 in which figures for total production during the three previous years were broken down into percentages produced under ceiling and various quota price categories. True, factors other than depleted ore reserves contributed to this picture. Among the more important of these, were shortage and high cost of labor, both skilled and unskilled, and the general difficulty and cost of maintaining adequate equipment and supplies. The cost of production in the Tri-State district was most affected.

Jan 1, 1946

For the year ending February, 1919 PRESIDENT SIDNEY J. JENNINGS NEW YORK, N. Y. PAST PRESIDENTS L. D. RICKETTS NEW YORK, N. Y. PHILIP N. MOORE ST Louis, Mo. FIRST VICE-PRESIDENT C. W. GOODALE BUTTE, MONT. TREASURER GEORGE C. STONE, NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W. RAYMOND, NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 7, 1918