Search Documents

C. A. ROSE, New York, N. Y. (written discussion *).-Without doubt the excellent results obtained at Ajo will cause surprise among metallurgists; 75 per cent. average capacity and 80 per cent. extraction during the first year of operation of a plant using a new metallurgical process are figures that speak for themselves. It is obvious that the most troublesome feature of the process is the fouling of solutions. The effects of this are most evident in the electrolytic tank house; but apparently the solutions are so heavily loaded with salts that their dissolving power is also impaired. This is indicated by the fact that copper comes into solution during washing after the leaching of the ore is completed, as shown by the decreasing ratio of acid to copper in the various washes tabulated in Table 4, and also by the fact that 4.9 per cent. of the total copper in the ore remains in the tailings in a soluble form. Even though the extraction in leaching and the ampere efficiency in electrolysis would be benefited by keeping the salts in solution at a lower concentration, it is doubtful whether it would pay to decrease these salts by discarding more electrolyte without other changes in the, process, since this would increase the amount of cement copper produced, which is already very large. If, however, it would not disturb the process otherwise, this object could be accomplished by increasing the range of electrolysis, so that solution going to the tank house would contain, say, 4 per cent. copper and 1 per cent. acid, and the solution returned to the leaching plant 1 1/2 per cent. copper and 4.8 per cent. acid, and by increasing the volume of solution to be discarded, this to be taken from the electrolyzed solution returned to the leaching plant. By this arrangement, more salts will be removed from the system per ton of cement copper produced; and if sufficient solution is discarded to keep the iron content down to 1 1/2 per cent. it would he feasible to recover the copper from

Jan 4, 1919

By AIME AIME

MORTIMER ELWYN COOLEY, dean of the College of Engineering and Architecture of the University of Michigan, has been elected president of the American Engineering Council of the Federated American Engineering Societies. This was announced at a meeting of the Executive Board of the Council held at the Cosmos Club in Washington on Sept. 30. Dean Cooley assumes office at once. The new head of organized engineering is a past president of the American Society of Mechanical Engineers and has a long record of distinguished service in education, under the government and in private capacities. He was born in Canandaigua, N. Y., March 28, 1855, and was graduated from the United States Naval Academy in 1878. With his classmate, Dr. Ira N. Hollis, he was ordered to the U.S.S. "Quinnebaug," then fitting out at the Norfolk Navy Yard preparatory to a cruise in the Mediterranean.

Jan 1, 1921

By Wm. Hamilton Merritt

IN this paper, which I have the honor to submit to the Institute, it is my intention to treat especially of that part of the North Staffordshire field which converges to a long tongue in the neighborhood of Congleton, and which includes the villages of New Chapel, Ford Green, Norton, Biddulph, Bradley Green, Gillow Heath, and the immediate vicinity. My object is not so much to give a minute description of the geology or systems of mining and smelting, as by a general review, some idea of the extraordinary facilities for the production of excellent iron, which have enabled this district to maintain its position more successfully than any of its rivals against the late depression in trade. The North Staffordshire coal field has the Cheshire and Lancashire fields some thirty-five miles to the north, those of Derbyshire and Nottinghamshire forty miles to the east, those of South Staffordshire and Shropshire, about thirty miles to the south, and the Denbighshire and Flintshire fields some forty miles to the west. It is highly probable that the coal continues under the new red sandstone to the Western and Southern fields as the dips on both sides, and absence of large faults, make it impossible to come to any other conclusion. In a section of this coal field, from Chatterly to Whitfield, thirty-two workable seams of coal are shown, of an aggregate thickness of 130 feet, varying from 2 feet 6 inches to 7 feet, and thirteen seams of ironstone, 24 feet, averaging from 2 to 4 feet. All of these seams have been minutely described in a paper by Mr. Charles J. Homer, read in 1875 before the British Iron and Steel Institute. In the northern part, to which I especially wish to direct your attention, the beds lie in a V-shaped basin, the underlying millstone grit and Yoredale rocks rising and forming escarpments on either side of the valley containing the coal. Throughout this district, at the outcrop of the coal, there are indications of old workings. A shaft 4 to 5 feet in diameter reaches the coal at about 14 yards from the surface, and from it the coal has

Jan 1, 1880

By T. Toda, R. Maddin

A study has been made of the microstructure and mechanical properties of splat-cooled aluminum-base gold alloys with gold concentration from 0.25 to 5.0 wt pct. These alloys have been quenched from the liquid state by a torsion-catapult technique, which has made it possible to pepare specimens suitable for mechanical property measwements. From the electron micrographs it has been shown that the solid solubility of gold in aluminum can be extended to 2.5 wt pct (0.35 at. pct) by splat-cooling, while the maximum equilibrium solubility is known to be less than 0.3 wt pct (0.04 at. pct). The very fine grain size (several tenths of a micron), the extended solid solubility, and the fine dispersion of a second phase (AuAl2) contribute concurrently to a substantial strengthening effect. In Al-5 wt pct Au splat-cooled specimens of less than 50 thickness, the yield strength is 17 kg per sq mm or 6 times as large as the strength of bulk specimens. For the Al-1.0 to 2.5 wt pct Au solid solution obtained by splat-cooling, the yield strength reaches 7.5 kg per sq mm after an aging treatment (for 10 hr at 200°C), while it is 3.7 kg per sq mm for the corresponding bulk specimens. A great deal of research has been done in recent years on the structure and the properties of metals and alloys rapidly quenched from the liquid state.' The term "splat-cool" has been used with the meaning of a rapid quenching from the liquid state., The splat-cooling techniques have produced large numbers of new structures, which are expressed in terms of metastable phases,3 concentrated solid solutions,4 amorphous phases,5'6 new phases,7 and so forth. Nearly all previous studies have concentrated on the physical properties; i.e., crystallography, structure, electrical resistivity, magnetism, and so forth, of the splat-cooled metals and alloys. The mechanical strength of splat-cooled metals and alloys has hardly been investigated except for some recent work by MOSS' on A1-V alloys. The principle common to all experimental techniques developed to obtain very rapid quenching rates is based on the heat transfer by conduction. Liquid must be in good thermal contact with a substrate of high heat conductivity. Both of the published devices known as the "gun" and the "piston and anvil" techniques suffer from certain shortcomings. For example, the specimen obtained by the gun technique is very small and flaky, and hence inadequate for mechanical properties measurements. On the other hand if the material is forced to yield a continuous speci- men by the piston and anvil technique, it is probable that some plastic deformation occurs during the quench. A novel method for rapid quenching of a liquid metal or alloy, the "torsion-catapult", has been devised by Roberge and Herman9 at the University of Pennsylvania. In the apparatus the melt is thrown out of a curved furnace by a catapult and impinges on a copper substrate. The apparatus has the advantage of producing a continuous foil which is relatively large in size and of a quality suitable for the measurements of mechanical properties. The quenching rate is estimated to be of the order of l05 to l06 ºC per sec, (comparable to rates achieved by the piston and anvil technique). In selecting an alloy to be studied we were made aware of the fact that gold was believed to be "insoluble" in in and consequently age hardening in the A1-Au system appeared to be interesting. Quite recently Heirnendahl13-15 revealed that the solid solubility, as determined by transmission electron microscopy, was 0.3 wt pct Au at 640°C and 0.25 wt pct Au at 600°C, decreasing with decreasing temperature. In an A1-0.2 pct Au alloy after quenching from a solution treating temperature of 600°C the yield stress was 2 kg per sq mm, and it increased up to 6 kg per sq mm after aging for 1 to 10 hr at 200°C. The precipitation occurred in the form of platelike particles mainly on (100) matrix planes. The intermediate phase n', the equilibrium phase n (AuAl2), and lattice relationships between both precipitates and the matrix were also investigated by electron microscopy. One of the purposes of the present research is to determine whether or not the solid solubility in this system, in which gold has a very small solubility in

Jan 1, 1970

By C. W. Hoffman, W. R. Hinken

Probability sizing, a fairly recent development in the field of particle separation, is now under investigation to determine its value to the mining industry. The method employed is probability sizing through a vibrating network of decreasing screen openings. While probability sizing is not new, the possibility of using it for coarse, highly abrasive ores at high tonnage rates has only recently appeared to merit practical consideration. The advantages of probability sizing vs. conventional screening methods are: (1) reduced space requirements for a high capacity unit, (2) fewer moving parts, (3) more versatile product sizing selection, (4) reduced maintenance requirements, and (5) lower power consumption. Screening is a necessary part of virtually every crushing circuit. At some stage in the process, particle separation becomes a controlling factor in the operation. The basic type of screen in use today is the vibrating unit, which usually employs a mechanical vibrator of one type or another to obtain sizing and material transportation across the screen surface. The vibrating screen has its limitations and inherent problems. Operators must live with: (1) high maintenance — worn rods, screen cloth, spacers, cross members, chutes, etc., (2) low capacity in relation to floor space requirements, (3) extreme noise levels, (4) high power consumption, and (5) structural problems in the screens and supporting steelwork. All plant operators have become tolerant of these drawbacks through the years, and little innovation has been developed in screening. The vibrating screens in use today incorporate improved metals, more efficient power sources, better lubricants, and increased manufacturing skill, but the basic machine itself remains unchanged. Screening is a relatively small part of most plants' operating expenditures and gets relatively little attention from research and development. The HiProb sizer is a new approach to the problem of particle separation on a high tonnage basis. Developed by Dr. Fredrik Mogensen (president of Fred-rik Mogensen, A. B. of Djursholn, Sweden), this unit has found its primary acceptance in the sizing of wet or dry materials in the fine ranges. Climax has been working cooperatively with Mine and Smelter Supply Company, the United States licensee, on the adaptation of the sizer to obtain consistent recovery at a high tonnage rate on a — 3/8-in. separation. This was a new application for the sizer and opened up a whole new field of problems. Dr. Mogensen's machine utilizes the control of normal probability of falling particles and is designed to eliminate some of the undesirable features of vibrating screens mentioned earlier. The machine is light, compact, consumes less power than conventional screens and has a low noise level. PRINCIPLES Probability sizing is a process designed to allow solid particles to segregate with a high ratio of the materials reporting into their respective size fractions with a minimum amount of misplaced particles. Sizing is defined in this paper as segregation of dry solid particles into fractions of comparable sizes. Probability is usually estimated as the ratio of the number of ways an event might occur vs. the total number of allowable ways. The probability process described depends upon the fact that particles falling through a network will segregate across the sizing surface even though all openings are larger than the particles. The degree of segregation is dependent upon the particle size and the trajectory applied by the sizing network to each falling particle. Specifically, the process utilizes a maze made up of screen cloth to control the path of a particle in free fall as illustrated in Fig. 1. The usefulness of this probability sizing process is dependent upon the degree of efficiency of an effective maze. Primarily, a maze must be extremely flexible to meet the multi-faceted nature of solid particles and, at the same time, the degree of control must be reproducible so that a desired separation is predictable. Dr. Fredrik Mogensen has formulated a maze that is not only flexible and easily controlled, but, mote importantly, easily adaptable to a working machine.

Jan 1, 1970

By C. H. Mathewson

MY first reflection on the subject assigned to me by the officers of this symposium was that a critical description of these lesser characters in the cast of inanimate actors now before us under the title "The Role of Metals in New Transportation" would be about as well received as the description of a horse race in terms of harness buckles and jock-ey's buttons. The word "new" in the title of this symposium seems to shout strong aluminum and stainless steel, unless we transfer our attention to transpor-tation on another planet where the strength-density ratios may require very different engineering treatment. To load a speaker with the "heavier nonferrous metals" amidst the airy consideration of flying or 20th century gliding along the earth and through water, like Hermes, the messenger of the immortals, and expect an instructive or enlivening flight into the area of current exploitation and popular interest in transportation would, of course, require the performance of a miracle or at least the exhibition of genius to which I can lay no claim. But copper and nickel, headliners in other classifications, are also indis-pensable as components of the important new structural materials of transportation, and together with lead, tin and zinc perform many minor or contributory functions in this field that may indeed be con-sidered well-nigh indispensable. A complete and well planned fabric of classification, explanation and critique of even these secondary functions would take much time, and I cannot hope in the 25 minutes or so alloted for the purpose to offer more than a rambling treatment, in which a thread of continuity will be sought by anchorage to one after another of the following attributes or appurtenances of the moving vehicle: 1. The machinery and accessories. 2. The framework and superstructure, and the line or travelway. 3. Light, heat, power, water, sanitary and housekeeping services. 4. Embellishment, or style.

Jan 1, 1936

By Simon D. Strauss

The world appetite for minerals in the, third quarter of this century grew at a higher rate than had been anticipated. To illustrate, consider the experience of four, commodities. Excluding the Communist bloc, sometimes referred to as the centrally planned economies, demand for aluminum increased at a compound rate of 8.6% between 1950 and 1975,; copper rose by 4.4%; iron ore by 5.5%; and tin, the laggard in the group, by 2%. Except for tin, the figures are substantially greater than growth rates anticipated in 1950 in the Paley Commission report and other studies. The growth rate was not evenly distributed in geographical areas. Professor Wilfred Malenbaum of the University of Pennsylvania did an interesting study breaking these figures down as among three principal sources of demand -- the United States, other industrialized nations (which he referred to as the "rich lands"), and the developing world (which he referred to as the "poor lands").

Jan 1, 1982

By C. EDWARD STAFFORD

A Discussion of the paper by Mr. James P. Roe which was read at the Washington meeting, May, 1905. MR. C. EDWARD STAFFORD, Chester, Pa.:-During all my business life, I have been engaged in the manufacture of Bessemer and open-hearth steels, but, during my long connection with the Shoenberger Steel Co. of Pittsburg, I had some experience in the manufacture of high-grade puddled iron for horse-shoes and in the making by Dr. Otto Wuth's process extremely pure low phosphorus puddled blooms (analyzing from 0.005 to 0.01 per cent. of phosphorus and sulphur), which were melted with low-phosphorus pig-iron in acid open-hearth furnaces to make extra locomotive fire-box steel. I have also seen the Dank's puddlers in operation at different times and places, notably where they were most successful, at the Otis Steel Works, Cleveland, Ohio; then under the management of our friend, Mr. S. T. Wellman. These Dank's blooms were made solely for open-hearth melting-stock to which they were well adapted ; the unavoidable presence of bits of ore-fix imbedded in the mass of the, metal always prevents the profitable manufacture of merchant iron from Dank's blooms. With the experience just described, I was to some degree in position to value fairly the means, methods and results of Mr. Roe's mechanical puddling from the metallurgical or technical and economic points of view, when given an opportunity by Mr. Roe to see his puddling furnace or machine in operation in Pottstown, Pa. Briefly, the furnace, with water-cooled bottom, is rectangular in plan, about 20 by 8 ft. in the clear, suspended by trunnions at the middle of the long sides, at a. height of 17 or 18 ft. above the general level; the oscillation (65° each way from the vertical) is accomplished by geared segments (attached to the downward-projecting side or trunnion-plates) with which engage pinions driven by a reversing engine. The whole section

Sep 1, 1905

By John L. Schroder

The demands for increased productivity on the 1967 coal industry have generated new operating trends and fresh approaches to old methods, which have enabled the industry to keep pace with the expanding economy. Changes, while not radical in concept or design, have been plentiful and are marked by the refinement of the already tried, tested and proven. Perhaps not since World War II have there been demands on equipment manufacturers to design and deliver such diversified types of machines as those required by the industry in the past year. Equipment developments-following a plan which calls for higher productivity, lower maintenance costs and greater machine availability- have tended more toward increased horsepower and heavier, more rugged equipment. Electrical and mechanical components, designed in many instances with maximum reliability rather than initial costs as the main criterion, have contributed to the improvements in over-all performance. High-strength, specialty steels are finding use in a wide range of equipment applications. The horsepower capacity of electric motors being installed is more frequently being rated on a continuous basis rather than the former one hr or less and, as a result, fewer failures now occur because of overloading. These developments reflect the pyramiding cost of equipment down-time and represent definitive progress in reducing the magnitude of the problem.

Jan 2, 1968

By Gerald G. Griswold, James O. Greenslade, Cherie Tilley, Richard Reseigh

INTRODUCTION The Harrison Western Corporation, a leading Denver based mine contracting and engineering concern, is presently engaged in sinking two 1,006 m (3,300 ft) shafts for the Phillips Uranium Corporation at their Nose Rock Project, approximately 13 miles northeast of the small community of Crownpoint in McKinley County, New Mexico. The Nose Rock Project is the first attempt by the Phillips Uranium Corporation to tap the deep uranium reserves in what has become known as the Grants Mineral Belt. (See Figure 1) Project Description Phillips Uranium Corporation's plan for the large 2700 metric ton per day (2950 tons/day) mining facility calls for a series of deep access and ventilation shafts ranging from 4.27 m (14 ft) to 5.49 m (18 ft) in diameter to approximate depths of 1,006 m (3,300 ft). The initial pair of shafts consists of one production shaft and one ventilation shaft separated by a distance of 91 m (300 ft). The interbedded layers of sedimentary sandstones and shales to be penetrated by the shafts contain several major water producing aquifers, the deepest being the mineralized zone called the Westwater Canyon Member of the Morrison Formation. A series of temporary and permanent water pumping stations is planned. Generally, the temporary stations are located above major aquifers to facilitate water removal while sinking through the aquifer and the permanent stations constitute what, in the final mode, will be the mine dewatering system. In addition, Phillips Uranium Corporation has In- stalled and is maintaining a system of depressurization wells that temporarily pump the major aquifers and considerably reduce the water inflows during shaft construction. The major aquifers are also chemically grouted prior to sinking. Site work for the project was initiated in the fall of 1976. Full scale shaft sinking commenced in November of 1977 on the 4.88 m (16 ft) diameter ventilation shaft and on the 5.49 m (18 ft) production shaft by another contractor. Harrison Western Corporation began work on the project on November 4, 1979 wlth the production shaft at a depth of 633 m (2,076 ft) and the ventilation shaft at a depth of 474 m (1,554 ft). This paper will address only the portion of shaft sinking completed by Harrison Western. Geology and Hydrology The Nose Rock Project is located on the Chaco Slope in the southern extreme of the San Juan Basin in northwest New Mexico. The southern San Juan Basin is generally bound by the Defiance Uplift to the west, the Zuni Uplift to the south and the Nacimiento Uplift to the east. The Grants Mineral Belt occupies most of the southern portion of the San Juan Basin and this project is located on the northern extreme of the Grants Mineral Belt. The San Juan Basin is comprised of sedimentary rock of continental, marginal-marine and marine origin, that dip northward from the Zuni Uplift and Chaco Slope into the interior of the San Juan Basin. (See Figure 2) Major Formations The major geologic formations to be penetrated range from mudstone and shales to siltstones and sandstones. The sandstones are highly productive aquifers which, under static conditions, would flow artesian. Water temperatures in the aquifers are high and therefore are a force to be dealt with. Temperatures range from 18ºC (65OF) in the upper aquifers to 48ºC (118º'F) in the lower. The mudstones are generally bentonitlc. (See Figure 2) GALLUP SANDSTONE: The Gallup Sandstone is the first major regressive wedge in the San Juan Basin of the Cretaceous era and at this project is about 35 m (115 ft) thick. It is medium grained and prior to depressurization carried a hydrostatic water pressure of over 72.5 kg per cm2 (1,031 psi) which 1s artesian. Compressive strength ranges from 334.7 kg per cm2 (4,760 psi) to 421.8 kg per cm2 (6,000 psi). Water temperature is approximately 30°C (86°F).

Jan 1, 1982

By George H. K. Schenck, Peter G. Donald

There is an accelerating acceptance of change by management of cement companies. Diversity of response is noticeable in efforts across the country to reverse the downward trend in profits that brought margins in 1966 to the lowest point in 20 years. New concepts are emerging among managers as they seek to increase the efficiency in use of the basic corporate resources of men, capital and technology. The shift towards computerized control of cement manufacturing is making new gains as is diversification of cement companies into allied fields such as production and sale of natural and light- weight aggregates, crushed stone and concrete products. Increased interest in special products such as white cement and further moves overseas are also significant. Perhaps the most dramatic event of recent years occurred in Washington at hearings before the Federal Trade Commission where cement producers split on whether there should be FTC guidelines that would prevent ownership of ready-mixed concrete producers by cement companies.

Jan 4, 1967

By G. P. Pilling

The use of magnetic ore in the blast furnace is a subject of increasing importance. The end of the deposits of lake ore is in sight, although not imminent, and unless some new field is discovered, the use of magnetites will be an increasing factor in the iron production of the country. Enormous deposits of magnetic ore in the country that have been practically untouched contain ore of sufficient richness and purity to prolong materially our ore supply without extensive importation of foreign ores. Magnetic ores can be divided into three general classes: Fine un-sintered, or raw ore; raw lumpy ore; fine ore that has been sintered. Fine Unsintered Ore Typical analysis and screen test of this class of ore from the Adirondack region is as follows: Per Cent. SCREEN TeST pER Cent. Fe.................... 58.00 Remaining on 4 mesh........... 7.50 SiOz.................. 7.50 Through 4 on 8 mesh........ 13.75 Al,O,................. 1.60 8 on 10 meah........ 3.75 Baseg................. 2.77 10 on 20 mesh........ 22.50 P.................... 1.00 20 on 40 mesh........ 27.50 Mn................... 0.13 40 on 60 mesh........ 2.50 S..................... Trace 60 on 80 mesh........ 10.00 80 on 100 mesh........ 2.50 100 mesh........ 10.00 100.00

Jan 1, 1923

By G. P. Pilling

The use of magnetic ore in the blast furnace is a subject of increasing importance. The end of the deposits of lake ore is in sight, although not imminent, and unless some new field is discovered, the use of magnetites will be an increasing factor in the iron production of the country. Enormous deposits of magnetic ore in the country that have been practically untouched contain ore of sufficient richness and purity to prolong materially our ore supply without extensive importation of foreign ores. Magnetic ores can be divided into three general classes: Fine un-sintered, or raw ore; raw lumpy ore; fine ore that has been sintered. Fine Unsintered Ore Typical analysis and screen test of this class of ore from the Adirondack region is as follows: Per Cent. SCREEN TeST pER Cent. Fe.................... 58.00 Remaining on 4 mesh........... 7.50 SiOz.................. 7.50 Through 4 on 8 mesh........ 13.75 Al,O,................. 1.60 8 on 10 meah........ 3.75 Baseg................. 2.77 10 on 20 mesh........ 22.50 P.................... 1.00 20 on 40 mesh........ 27.50 Mn................... 0.13 40 on 60 mesh........ 2.50 S..................... Trace 60 on 80 mesh........ 10.00 80 on 100 mesh........ 2.50 100 mesh........ 10.00 100.00

Jan 1, 1923

By W. R. Ingalls

In choosing the unusual title given to this paper, in which the term "cyclic " might be substituted for "intermittent," my idea has been simply in respect of precision. We might say old method vs. new method, but that antithesis implies something of substitution that has not occurred and perhaps is not in sight. We may say horizontal retorts vs. vertical, but none of the older retorts are truly horizontal, and there are three different types of vertical retorts. Other complexities might be suggested. There is, however, a broad distinction between distilling that is accomplished in a periodic cycle, generally daily; and distilling that is accomplished continuously, irrespective of whether it be done in the vertical retorts of the New Jersey process or in the retorts of the Trollhät-tan process. In offering a summary of the present state of the art with the intermittent process, I shall not have any idea of exemplifying it through descriptions of any single plants, but shall rather divide among the main steps of the process and outline what is best developed among them. In pursuing this thought, it will manifestly be impossible to make a composition that will exemplify the acme of good practice, for the latter will always be a function of the cost of labor, fuel, etc., which are widely variable. As of 1929, in respect of labor we might generalize the average plant wage in the Pittsburgh-Wheeling district of the United States at $5 per day; in Oklahoma at $3; in Great Britain at $3; in Germany at $1.75-$2; in Belgium and France at $1. With high labor costs the metallurgist will naturally use means of the nature of mechanization that with low labor would be uneconomical when capital charges are taken into account. Nor may we from records of performance safely make positive deductions in respect of the efficiency of different types of furnaces unless they have been tested comparatively under identical conditions in the same works. We shall find gas-fired regenerative furnaces showing coal consumption from 1.2 tons down to 0.7 per ton of roasted ore, which may be ascribable to difference in the thermal value of the coal that is used or to differences in proportions of the parts of the furnace, which is something quite distinct from the principle of the furnace. Thus, we have

Jan 1, 1937

By Roswell Johnson

To know the rate of decline of oil wells is very important, yet ordinarily we are prevented from getting this rate because the oil from several wells is put into one or a few tanks as soon as the wells have been connected to the power. The object of doing this is economy of tanks, pipes, labor and accounting. FIG. 1. But we are making a great sacrifice for this small economy. The advantages of the individual records are that we would know better: 1. When the well has ceased to be profitable. 2. When a well has gotten into bad condition. 3. The real record of the yield per acre and the rate of decline of the wells. The lease total is too mixed as to age of the wells for existing records to have much significance. To obtain such individual well records and more accurate logs are the great desiderata of satisfactory management of oil properties. 4. Which wells show the slowest decline-information which is valuable in locating new wells or purchasing adjoining leases.

Jan 6, 1917

By M. Duclos, A. Sawatzky

A simple model has been developed which describes the steady-state solute distribution in Ti-H type systems above the eutectoid temperature in the presence of a temperature gradient. The solute distribution is dependent on the shape of the phase boundaries. An interesting result, and one that is not observed at steady state in thermal diffusion below the eutectoid temperature, is the existence of a two-phase region. The heat of transport for hydrogen in a titanium, Q*a, over the temperature range 275" to 650.C is determined to be 4500 * 230 cal per mole. The heat of transport for hydrogen in B titanium, QB* over the temperature range 320" to 590.C is found to be 630 ± 200 cal per mole. It is also shown that thermal diffusion provides a method by which phase bounduries above the eutectoid may be determined in Ti-H type systems. IN modern technology materials are being used at constantly increasing temperatures under greater temperature gradients. Thus atomic migration in metal alloys due to a temperature gradient (thermal diffusion) may in some cases occur to an observable extent. The thermal diffusion of hydrogen in zirconium has in recent years received considerable attention1-' because of the use of zirconium alloys in nuclear power reactors. The thermal diffusion kinetics below the eutectoid (547°C) are fairly well understood. At steady state the solid solution, a, and hydride, 6, phases are completely separated with the hydride precipitating at the lower temperatures. No experimental work has been carried out in the a + B region although Droege4 suggested that a complete separation of the two phases, as observed at temperatures below the eutectoid, might not always occur. In the present investigation a simple model has been used to determine the steady-state solute distribution under a temperature gradient in Zr-H type systems heated above the eutectoid temperature. The solute distribution is shown to be dependent on the shape of the phase boundaries in the constitutional diagrams and several typical cases are discussed. The model has been applied to Ti-H. This system was chosen in preference to Zr-H because of its much lower eutectoid temperature (-300°C as compared with 547.C), thereby reducing experimental errors due to oxidation and hydriding. The heats of transport for hydrogen in the a and B phases of titanium also have been determined since they were required to compare the proposed thermal diffusion model with experiment. THEORY In the presence of a temperature gradient the atomic flux in a single-phase region of a two-com-ponent system of which the atoms of only one component are diffusing is given by:' J = - U\dx + RT3 dx) which can be written as: j-D(dn/dt +Q*n/RT2)dt/dx [11 J - -D\dT + RT2)dx [1] where D = diffusion coefficient, n = solute concentration, T = absolute temperature, R = gas constant, dT/dx = temperature gradient, and Q* = heat of transport. At steady state (J = 0) Eq. [I] leads to the solute distribution: n = noexp Q*/RT where no = a constant depending on total solute content. The heat of transport Q* can be experimentally determined from the steady-state distribution. In the present paper we shall determine the solute distribution in systems having the constitutional diagram exemplified by Ti-H shown in Fig. l.' As shown, N,(T) and NB(T) are the equilibrium solute concentrations in the a and 0 phases at temperature T. Lines AA' and CC' define the region of interest to us. The following assumptions are made: 1) Steady-state conditions prevail. 2) In a single-phase region all points on an isotherm have the same thermodynamic potential so that the composition over an isotherm is uniform. If a two-phase region exists, thermodynamic equilibrium is found only at phase interfaces. However, we assume the component of the concentration gradient along an isotherm to be small so that the composition in each phase is approximately the same as at the interface and is given by the constitutional diagram, Fig. 1. 3) There is appreciable diffusion of only one component. 4) We shall consider only the case where Qa*, QB*, and Qg*, the heats of transport for solute diffusion in the a, B, and 6 phases, respectively, are positive. This has been observed for the thermal diffusion of hydrogen in zirconium3 and titanium.10 We will show that the steady-state solute distribution above the eutectoid is primarily determined by the heats of transport and the temperature dependence of Na(T) and Np(T). It may be quite different from the steady-state distribution below the eutectoid. For example, we will see that, under certain conditions,

Jan 1, 1970

By Charles H. Snow

In vol. xxxviii. (1889) of the American Journal of Science, under the heading " Pseudomorphs of Native Copper after Azurite from Grant County, New Mexico," Mr. W. S. Yeates describes a most interesting mineral form. His account is, that a material having the appearance of native copper, but brittle and much lighter than native copper (its specific gravity being but 4.15), was submitted to him by the United States National Museum for examination. The substance was reported to him as occurring in masses, varying in weight from one ounce to seventy pounds, and composed of tabular crystals, variously grouped. The specimens, when submitted, ex hibited on the outride a covering of clay; and they were subse quently found to consist of particles of the same clay, intimately mixed with others of native copper, producing the aspect, without the weight, of pure copper. The forms of the azurite crystals, found at Bisbee, Arizona, having been suggested by the specimens, actual goniometer-measurements were made; and the two crystallizations were thus proved to be identical. To these statements I may be permitted to add some further in formation, derived from personal examination, and illustrated with a suite of characteristic specimens collected by myself (Fig. 2).* Grant County, New Mexico, in which these specimens were found, is a region noted for variety of mineral species. The sixth edition of Dana's Mineralogy mentions many of the silver, copper, and lead minerals, and also turquois, aragonite, wulfenite, barite, fluorite, vanadinite, etc. I have noticed also green and red garnet, molybdenite, native alum, smithsonite, bornite, etc., some of which presented peculiar modes of occurrence. The green garnet, for instance, was in masses formed of separate crystals, each of pea-size and not unlike that vegetable in tint and smooth opaqueness. The crystallization was

Jan 1, 1893

By Alden B. Greninger, Alexander R. Troiano

The crystallographic mechanism for the austenite-to-martensite trensformation has been deduced from the results of the following new experimental determinations: (I) the accurate evaluation of the lattice relationship between austenite and individual crystals of martensite—and thus the relationship between the martensite lattice and the martensite plate, and (2) the measurement and analysis of the change in positions that a volume of austenite unclergoes when it transforms into a crystal of martensite. For the latter study, a new tool was developed, the stereographic analysis of shear. Lattice relationship.—Thirty-five separate 50-gram melts of an alloy containing about 22 per cent nickel and 0.8 per cent carbon were prepared in a high-vacuum furnace. This alloy is all-austenite at room temperature; grain size was about I cm. Specimens of the alloy were cooled to about — 70°C. to form a few martensite crystals, and suitable specimens were ground and polished on a surface parallel to a single martensite plate, exposing the martensite crystal for an area of 1 mm. or more. Four martensite cystals from four diffierent ingots were prepared in this manner; the largest crystal of this group is illuslratecl in Fig. I. Back-reflection Laue patterns were obtained from martensite crystals (and the matrix austenite) both before and after tempering. The locations of the basal-plane pole of martensite was checked by means of oscillating crystal X-ray patterns. All four crystals studied yielded the same solution ( ± 0.5°), and these relationships are expressed in gnomonic projection in Fig. 3.* The narrow dark-etching bands often visible in martensite "needles" were found to be parallel to (112) and thus are undoubtedly twin bands in the martensite crystal.

Jan 1, 1941

By Alden B. Greninger, Alexander R. Troiano

THE crystallographic mechanism for the austenite-to-martensite transformation has been deduced from the results of the following new experimental determinations: (I) the accurate evaluation of the lattice relationship between austenite and individual crystals of martensite-and thus the relationship between the martensite lattice and the martensite plate, and (2) the measurement and analysis of the change in positions that a volume of austenite undergoes when it transforms into a crystal of martensite. For the latter study, a new tool was developed, the stereographic analysis of shear. Lattice relationship.-Thirty-five separate 50-gram melts of an alloy containing about 22 per cent nickel and 0.8 per cent carbon were prepared in a high-vacuum furnace. This alloy is all-austenite at room temperature; grain size was about I cm. Specimens of the alloy were cooled to about -70°C. to form a few martensite crystals, and suitable specimens were ground and polished on a surface parallel to a single martensite plate, exposing the martensite crystal for an area of I mm. or more. Four martensite cystals from four different ingots were prepared in this manner; the largest crystal of this group is illustrated in Fig. I. Back-reflection Lane patterns were obtained from martensite [ ] crystals (and the matrix austenite) both before and after tempering. The locations of the basal-plane pole of martensite was checked by means of oscillating crystal X-ray patterns. All four crystals studied yielded the same solution (±0.5°), and these relationships are expressed in gnomonic projection in Fig. 3.* The narrow dark-etching bands often visible in martensite "needles" were found to be parallel to {112} and thus are undoubtedly twin bands in the martensite crystal.

Jan 1, 1941

By Alden B. Greninger, Alexander R. Troiano

The crystallographic mechanism for the austenite-to-martensite trensformation has been deduced from the results of the following new experimental determinations: (I) the accurate evaluation of the lattice relationship between austenite and individual crystals of martensite—and thus the relationship between the martensite lattice and the martensite plate, and (2) the measurement and analysis of the change in positions that a volume of austenite unclergoes when it transforms into a crystal of martensite. For the latter study, a new tool was developed, the stereographic analysis of shear. Lattice relationship.—Thirty-five separate 50-gram melts of an alloy containing about 22 per cent nickel and 0.8 per cent carbon were prepared in a high-vacuum furnace. This alloy is all-austenite at room temperature; grain size was about I cm. Specimens of the alloy were cooled to about — 70°C. to form a few martensite crystals, and suitable specimens were ground and polished on a surface parallel to a single martensite plate, exposing the martensite crystal for an area of 1 mm. or more. Four martensite cystals from four diffierent ingots were prepared in this manner; the largest crystal of this group is illuslratecl in Fig. I. Back-reflection Laue patterns were obtained from martensite crystals (and the matrix austenite) both before and after tempering. The locations of the basal-plane pole of martensite was checked by means of oscillating crystal X-ray patterns. All four crystals studied yielded the same solution ( ± 0.5°), and these relationships are expressed in gnomonic projection in Fig. 3.* The narrow dark-etching bands often visible in martensite "needles" were found to be parallel to (112) and thus are undoubtedly twin bands in the martensite crystal.

Jan 1, 1941