Search Documents

By O. W. Shimer, D. C. Helms, C. E. Brown

THE early history and progress of anthracite stripping, from the first known operation at Summit Hill in 1821 through 1917, was covered in 1917 in a paper by J. B. Warriner,1 then chief engineer, now president of the Lehigh Navigation Coal Co., and stripping methods between 1917 and 1931 were the subject of a paper in 1931 by H. H. Otto,2 of the Hudson Coal Company. The present paper is confined to methods used today on pitching beds in the western middle and southern anthracite fields. The anthracite industry, not unlike other large industries, had been affected for more than a decade by the adverse economic conditions of the country. High development and operating costs and the competition of other fuels caused some collieries to be closed temporarily, while others were permanently abandoned. In order to obtain a larger tonnage at a lower development cost, a larger stripping program was put into effect by many companies. In 1932, stripping operations accounted for 334 million tons, or 7 per cent of the total anthracite production of the year, and in the next 10 years this increased until more than double that amount, or over 14 per cent of the total production, was from stripping operations. These figures represent the total production of the entire anthracite region; unfortunately, the figures have not been separated from the different fields. There are some operations in the southern and middle western fields where the tonnage obtained from stripping amounts to more than 30 per cent of the total colliery production. Stripping operations on pitching beds present difficult problems. Owing to the various geological formations, a different situation is encountered in nearly every stripping pit; and because of the proximity of an overlying bed, it is very often necessary to load the entire overburden into trucks and haul it out of the pit to the dump area, although back filling and casting is done whenever possible. Beds in the areas described in this paper pitch from 20° to 90° and some are on the invert in, many sharp folds and faults. PLANNING The more successful strippings have had adequate engineering analysis. Some work is being done without much preliminary planning, but many strippings would have failed completely if close supervision by the engineering department had not been maintained. Locations of stripping areas are determined as follows: 1. By constructing cross sections over the areas and drilling sufficient diamond-drill or well drill holes to study the strata and to determine the location, thickness and pitch of the beds.

Jan 1, 1944

The Secretary : The work of Mr. A. E. Outerbridge, Jr., of Philadelphia, first made known in his paper on " The Mobility of Molecules of Cast-Iron," read at the Pittsburgh Meeting of the Institute, in February, 1896, has been reviewed by the Committee on Science and the Arts of the Franklin Institute, whose report, dated May 5, 1897, is accompanied with a table of tests made by the Committee, and amply confirming the statements of Mr. Outerbridge. Concerning the originality and novelty of his investigation, the Committee says: " The fact that a certain molecular change takes place in cast-iron in the course of time has been known and recognized by many persons for a long time, and that this change tends to relieve the internal strains and render the casting tougher has often been noticed and acted on, although in a very crude way; but, so far as the sub-committee has been able to learn, Mr. Outerbridge has been the first to make a careful study of this, and to note that the change may be hastened by impact, and the whole effect produced in a short time, and also to make a scientific study of the phenomenon. We believe great credit is due him for the initial observation and the careful work dependent thereon. The results were first given to the public in a paper read before the American Institute of Mining Engineers, on February 20, 1896. This aroused a wide-spread interest and discussion among users of cast-iron, and so far as the sub-committee has been able to determine, it has not been shown that anyone, either in this country or abroad, has antedated Mr. Outerbridge in his work in this line. The Franklin Institute therefore recommends the award to him of the John Scott Legacy Premium and Medal." This report has not been published, hut I have had the opportunity to read it in manuscript. The table of testa accompanying it comprises 91 tests of " rumbled" and an equal number of " not rumbled" companion-bars of cast-iron, 26 by 2 by

Jan 1, 1898

By J. F Haseman, J. E. Davenport

In the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1,2 results in inadequate beneficiation. Investigation of Flotation Methods Flotation has been used in 'Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate. 3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P2O5 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P2O5, 20; SiO2, 40; CaO, 29; Fe2O3, 2; Al2O3, 3; F, 2.3. The particle-

Jan 1, 1948

By J. F. Haseman, J. E. Davenport

In the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1,2 results in inadequate beneficiation. Investigation of Flotation Methods Flotation has been used in 'Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate. 3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P2O5 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P2O5, 20; SiO2, 40; CaO, 29; Fe2O3, 2; Al2O3, 3; F, 2.3. The particle-

Jan 1, 1948

By W. David Menzie

An inventory of the mineral resources of a region is a most desirable basis for planning their systematic development. In the absence of appropriate samples upon which to base a reliable estimate of this inventory, investigators have resorted to a number of indirect approaches; the unit regional value concept forms the basis for one such approach. The produced resources of a region are a function of the inventory multiplied by the degree of intensity (some fraction between zero and one) of development of the resources. A convenient means of expressing this amount is to accumulate the weight and value of resource and to prorate the totals over the area represented by the unit sampled; i.e., weight and value per unit area or tonnes/km.2 and U.S. 1967 $/km.2. When this approach is used for the U.S.A., South Africa and Rhodesia the average value of (log.) U.S. 67$/km.2 for the states of the U.S.A. and South Africa are similar ($55,176 U.S.$67/km.2 and $52,538/km.2 respectively); whereas, Rhodesia is relatively underdeveloped (10,301 U.S.67$/km.2). On the other hand if the individual commodities are used as a basis for comparison, the U.S.A. shows the greatest diversity (67 commodities out of a possible total of 75) with South Africa next (50 commodities) and Rhodesia last with only 26 commodities. Since it is known that area and value are not simply related perhaps diversity is directly related to area. Again the kinds of commodities which have contributed the greatest value to the totals differs, with fuels (petroleum, coal and natural gas) predominating in the U.S.A. totals; whereas, South Africa and Rhodesia obtain their greatest contributions from gold, diamonds (S. Africa) coal and asbestos. In each case the greatest value of resources is produced from sedimentary rocks. As a somewhat different kind of example, consider a single resource (petroleum, the most valuable in the U.S.A.) over a large area (number of sampling units) the U.S.A. by state. Furthermore, assume that the model frequency distribution of the amount of petroleum (tonnes/km.2) is log normal. Then the present production fails to match the model first because 17 states (34% out of 50) have not produced petroleum. Of the remaining 33 states, Louisiana has produced the most (15,177 tonnes/km.2) and the frequency histogram is still skew. A spatial analysis of the distribution of the amount of petroleum by state shows that the samples (i.e., states) are not random; the non-producers and producers tend to cluster. It remains to be seen if this is indeed a true representation of the incidence of petroleum or is a function of the exploration philosophy currently in vogue.

Jan 1, 1977

By Max Hebgen

I. Natural Features of State Affecting Power Development .. 792 II. Early Developments. 1. Big Hole Plant................. 792 2. Canyon Feny Plant............... 793 3. Madison Plant No. 1............... 593 4. Black Eagle Plant................ 795 III. Later Developments. 1. Madison River System .............. 795 2. Missouri River System.............. 797 3. Great Falls System............... 797 4. Missoula River Development............ 797 5. Big Fork Development.............. 802 $ IV. Present Capacity of Power Developments....... 802 V. Transmission System...............: . 802 VI. Character of Load. 1. Lighting and Small Power Uses........... 804 2. Street Railways ................ 804 3. Mining................... 804 4. Railroads.................... 808 5. Irrigation................... 810 VII. Operation of System................. 812 VIII. Increase in Use of Power............... 811 IX. New Power Developments............... 814 X. Undeveloped Powers................. 815 It is estimated that the total stationary power now used in the United States. steam. water and gas. is probably over 30.000.000 h. p. The total developed water power is about 6.000.000 h. p. The water power in the United States now economically capable of development probably exceeds 25.000.000 h. p. The total developed and undeveloped power is

Jan 1, 1914

By D. V. Carter, D. C. Williams

Four oil discoveries were made in east and east central Texas during 1940, three of which represented new fields. In the Chapel Hill field, Smith County, oil was found where formerly only gas and distillate were produced. The three oil fields discovered are: Hawkins, Wood County; Pittsburg, Camp County; and Tehuacana, Limestone County. Important extensions were made to the following fields: Bazette, Navarro County; Long Lake, Anderson and Leon Counties; Cayuga, Anderson, Freestone and Henderson Counties; Opelika, Henderson County; and Talco, Titus and Franklin Counties. At the close of the year 54 oil and gas fields were producing in the district. There were 13 other fields, 11 oil and 2 gas, which have been abandoned. The East Texas field led the district in the number of completions for the year. During the year about 622 wells (oil and distillate wells included) were completed and 80 wildcats were drilled. Production and Proration During the year 170,424,685 bbl. of oil (distillate production included) were produced in the district—a decrease of 2.6 per cent from the 175,053,729 bbl. (distillate production included) during the preceding year. The district's production for the year 1938 was 182,369,484 bhl. As usual, most of the district's annual production was in the East Texas field, which produced 139,095,694 bbl. (distillate production in- cluded) during 1940, or 81.6 per cent of the total oil produced as compared with 141,333,317 bbl. (80.7 per cent) for 1939. The December estimated daily average production in the district was 424,565 bbl. The district accounted for 34.9 per cent of the state's annual production, compared to 36.7 pcr cent of the state's 1939 production. The decrease in production for 1940 may be attributed to changes made in proration schedules. Any material changes in the district's annual production may be considered for the most part as a reflection of proration-schedule changes affecting the East Texas field, since it is by far the most important field in the area. The entire state was subject to 71 shutdown days for the year; the East Texas field to 131; and the Rodessa field (Cass County, Texas, portion) to 5 days. No important changes were made in field rules and regulations during the year regarding the allocation of oil in individual fields in this district. Discoveries The Hawkins field is in southeastern Wood County in and principally north of the town of Hawkins. Development to date indicates that the field is somewhat of an elongated anticline trending slightly east of north and the proved oil area appears at this time to cover approximately 4000 acres. The oil production has been secured from the Woodbine sand, Upper Cretaceous; a considerable quantity of gas has been encountered in the Sub-Clarksville formation (Eagleford shale) in the higher part of the structure. It appears that a free gas

Jan 1, 1941

By D. C. Williams, D. V. Carter

Four oil discoveries were made in east and east central Texas during 1940, three of which represented new fields. In the Chapel Hill field, Smith County, oil was found where formerly only gas and distillate were produced. The three oil fields discovered are: Hawkins, Wood County; Pittsburg, Camp County; and Tehuacana, Limestone County. Important extensions were made to the following fields: Bazette, Navarro County; Long Lake, Anderson and Leon Counties; Cayuga, Anderson, Freestone and Henderson Counties; Opelika, Henderson County; and Talco, Titus and Franklin Counties. At the close of the year 54 oil and gas fields were producing in the district. There were 13 other fields, 11 oil and 2 gas, which have been abandoned. The East Texas field led the district in the number of completions for the year. During the year about 622 wells (oil and distillate wells included) were completed and 80 wildcats were drilled. Production and Proration During the year 170,424,685 bbl. of oil (distillate production included) were produced in the district—a decrease of 2.6 per cent from the 175,053,729 bbl. (distillate production included) during the preceding year. The district's production for the year 1938 was 182,369,484 bhl. As usual, most of the district's annual production was in the East Texas field, which produced 139,095,694 bbl. (distillate production in- cluded) during 1940, or 81.6 per cent of the total oil produced as compared with 141,333,317 bbl. (80.7 per cent) for 1939. The December estimated daily average production in the district was 424,565 bbl. The district accounted for 34.9 per cent of the state's annual production, compared to 36.7 pcr cent of the state's 1939 production. The decrease in production for 1940 may be attributed to changes made in proration schedules. Any material changes in the district's annual production may be considered for the most part as a reflection of proration-schedule changes affecting the East Texas field, since it is by far the most important field in the area. The entire state was subject to 71 shutdown days for the year; the East Texas field to 131; and the Rodessa field (Cass County, Texas, portion) to 5 days. No important changes were made in field rules and regulations during the year regarding the allocation of oil in individual fields in this district. Discoveries The Hawkins field is in southeastern Wood County in and principally north of the town of Hawkins. Development to date indicates that the field is somewhat of an elongated anticline trending slightly east of north and the proved oil area appears at this time to cover approximately 4000 acres. The oil production has been secured from the Woodbine sand, Upper Cretaceous; a considerable quantity of gas has been encountered in the Sub-Clarksville formation (Eagleford shale) in the higher part of the structure. It appears that a free gas

Jan 1, 1941

By L. Bombardieri, H. F. Mills

IRON KING mine, producing gold-silver-lead-zinc ore, is 10 miles east of Prescott, Ariz. At present the 1806 level is being developed. The echelon pattern of ore deposit continues at depth but is less pronounced, and the orebody is now more or less continuous over 2600 ft of strike length. with widths 5 ft to as high as 26 ft where overlapping of lenses occurs in one section of the mine. Better continuity of ore at depth has encouraged systematic mining and improved plant facilities to offset higher operating costs. With favorable persistence of ore at depth. the three-compartment No. 6 hoisting shaft appeared inadequate to handle increased tonnage from greater depths, and in 1952, a four-compartment steel and concrete shaft was started. This is now at a depth of 1906 ft, and shaft pockets and loading cartridges are being installed on the 1806 level. Ore from the new shaft, hoisted in 51/2 -ton Jeto bottom dump skips, is dumped into a 500-ton shaft bin, from which it is fed to a 16x30-in. gyratory crusher and conveyed 415 ft through an undersurface concrete gallery to the secondary crusher and conveying system supplying the 900-ton mill. Lead, zinc, and pyrite concentrates are floated, and the flotation tailings are cyanided after desliming. Waste from the new shaft is dumped into a 250-ton surge bin, fed from this bin to a 24-in. conveyor, and discharged into the glory hole above the block cave. The new shaft is served by a double-drum 400-hp hoist used for ore and waste; the No. 6 shaft conveys men and material To secure a cheap source of waste fill for stoping operations, a block cave area was undercut In the hanging wall near the north end of the mine above the 600 level. Waste from the block cave is drawn from any of three large drawpoints on the 600 level, and a series of hanging wall transfer raises with controls and bypasses on each level provide a fast low-cost material for fill. The block cave is worked vertically through to surface in the form of a steep-sided hole 350x250 ft and several hundred feet deep, the sides of which cave and provide fill material without any blasting. Fill is a mixture of caliche-cemented surface gravel and small particles of hanging wall schist. Level Development: An orebody 300 times as long as it is wide requires a lot of development work. Former practice consisted of driving a haulage drift about 30 ft from the ore in an andesitic footwall, a drift on the ore, and crosscuts from the haulage drift at 100-ft intervals. Crosscuts are about 90 ft long. At present, only the odd numbered levels are so developed, and on the even numbered levels only the haulage drift and crosscuts are driven. Little or no timber is used for this development. This change resulted in 20 pct reduction of development costs and 50 pet reduction of square set stoping required for removal of floor pillars. Elimination of ore drifts on alternate levels leaves

Jan 1, 1957

By John V. Beall

Never having done it before, it took us all day and until 11 at night to select and pack for a four-day back- pack trip up Lake Chelan last month. When we were through, we couldn't lift our own pack and Sylvia's, OUT spouse's, we barely managed to budge. Nevertheless, the next morning we were at the dock to board the Laldy of the Lake for the 3 ½ -hr boat trip to Lucerne. Our dress and accouterments creating the appearance of a veritable expedition into the wilderness made a sharp contrast with our fellow passengers, a senior citizens tour group from Spokane. We had come out to Seattle for the SME Fall Meeting and were taking advantage of the occasion for a vacation trip back to Lucerne and Holden where we had lived briefly 25-years ago, and a backpack trip up Railroad Creek from Holden to the Glacier Peak country, weather permitting. No matter what you say, weather is important, and this is one of the ingredients that went into making the SME Fall Meeting and Exhibit in Seattle, September 22-24, a thoroughly delightful experience for the 700 plus persons who attended. Seattle is a beautiful city, but with late September sunshine, which we experienced, it is the best. The second ingredient, is a swinging host committee. Under the leadership of Don Anderson and Tom Van Zandt, co-chairmen, and Mrs. Cecilia Reed, Ladies Program, superb hospitality and fine arrangements were blended. Earl Beistline, from Fairbanks, organized a two-day short course on arctic operations which preceded the meeting and drew an attendance of 44. Dick Robbins, in charge of arrangements, provided Masters-at- arms for technical sessions and a presentation of the colors by the U.S. Coast Guard at the Welcoming Luncheon. Eric Cheney's field trips ranged far and wide with events both before and after the meeting. David (Jeff) Kroft, capably managed audio-visual operations with a group of students from the University of Washington. Charles Hochmuth worked long, hard and effectively before and during the meet- ing on finances. Hank Reed, managed an authentic three-ring circus as Entertainment Chairman. His activities covered two cocktail receptions for all registrants and a dinner-dance. Dolph Campbell and Joe Hackbarth provided publicity by press and TV (see p. 37-40). SME's meetings have certain characteristics and possibly not all of these are known to everyone. The first of these is the deliberate involvement of the AIME Section in the area of the meeting. Most trade shows and conventions are run 100% by a professional staff and although SME staff could also do this, it has been our experience that a more friendly and better meeting results when the local members apply their talents. Actually SME only considers a site for a meeting after it has received an invitation from a Section. The knowledge of local conditions which Section committeemen bring to a meeting is of great value.

Jan 1, 1971

By Dr. O’Neil Thomas J., Donald W. Gentry

"If you can hold a board of cross directors In happiness against their gauzy schemes; If you can dodge the wrath of the electors Till dividends will flow as in their dreams; If you can make a mine pay from the grass roots No matter what the time or place or year; Then on my soul until the final blast shoots We'll add the title "MINING" when we call you "ENGINEER. " -From Wayne Darlington, "The Mining Engineer, " The Engineering and Mining Journal, Vol. 98, Sept. 26, 1914, p. 587. REASONS FOR THIS CHAPTER Up to this point in the book the material presented has addressed the fundamental parameters associated with the evaluation of mining ventures and other investment alternatives. The procedures and techniques illustrated represent the basic approach to project evaluation, particularly when considering the normal engineering economic analysis of investment proposals. The evaluation procedure is complicated, however, when dealing specifically with mining-related investment proposals. These complicating factors are invariably directly related to the many special characteristics of the mining industry. Many of these special features such as tax policies, revenue and cost estimation, and ore reserves have been addressed in previous chapters. In addition to the many special features of mining which directly impact, in a quantitative manner, the various line items in the pro forma income statements of a cash flow analysis, other features of mining affect evaluation procedures in a more general manner. The main purpose of this chapter, then, is to provide an exposition of some of these more qualitative factors. We hope this will enable the reader to recognize these factors in mine evaluation practice and to make suitable adjustments in his or her analysis.

Jan 1, 1984

Jan 1, 1933

By LEONARD S. AUSTIN

THE works of The Boleo Mining Co. are situated at Santa Rosalia, Lower California, on the opposite side of the Gulf of California from Guaymas, the, nearest railroad town. The copper deposits were discovered in 1868, and the name Boleo arose from the fact that the ore particles were agglomerated as little balls of carbonate or oxychlorides of copper. When worked on. a small scale, only ore carrying 20 to 25 per cent copper was mined; this was shipped to Europe for reduction In 1884 The Boleo Mining Co. was organized and,-the mine put in condition. Even then, due to the low price of copper, only the richer ore continued to be shipped. To operate the mine successfully the company made radical changes in the methods of development and spent money freely for construction of adequate plants for the treatment of low-grade ore. Finally, the owners of the various adjacent mining claims combined their interests and formed a joint enterprise attractive to French capital.

Jan 1, 1929

By Mi Chung

T HE ore-dressing problem at Tul Mi Chung is complicated by the unusually complex nature of the ores. These come from replacement ore- bodies in limestone at the contact with a granite batholith, and contain copper, gold, silver, bismuth, molybdenum, iron, arsenic, zinc, and lead, the first two metals constituting the principal sources of profit. Iron is present as pyrite, magnetite, and hematite. Arsenic occurs both as mispickel and lollingite (FelAsa), the latter carrying a certain amount of finely divided gold. The gangue minerals are those typical of limestone con- tact-metamorphism and include a large percentage of garnet, together with diopside, serpentine, calcite, epidote, zoisite, actinolite, 'mica and other minerals. A part of the gold occurs in a free state; some is combined with chalcopyrite and lollingite, and a consider- able proportion is contained in the pyrite. Researches towards the improvement of recovery have been energetically conducted since 1915. Amalgamation, gravity concentrating tables, vanners, can- vas plants, etc., have all been tried and discarded in favor of flotation. It was very quickly established that fine grinding was essential for satisfactory recovery. This was and is still accomplished in Hardinge ball and pebble mills. A comparative test showed that when the ore was crushed to the point at which it contained 20 to 26 per cent. coarser than 100 mesh, the gold recovery was only 55.9 per cent., whereas when crushed so that only 11 to 15 per cent. was coarser than 100 mesh, the gold recovery was increased to 82.5 per cent. No particular difficulty was ever experienced in making a satisfactory recovery of copper but the losses in gold were considered serious and led to the investigation described in this paper.

Jan 1, 1924

By Charles Dorrance

Culm is a general term used in the anthracite regions for many years to denote a mixture of coal, bony coal and impurities which is sent to the refuse-banks. Thus, 35 years ago culm contained the pea and buckwheat sizes of anthracite; but to-day, and as mentioned in this paper, culm is used specifically to denote the material which passes through the smallest screen in the anthracite-breaker. The smallest size of commercial anthracite is known as No. 3 buckwheat, barley, or bird's-eye coal, and is ordinarily made through a round-punched plate having openings & in. in diameter, and over a round-punched plate with openings 3/32 in. or 1/16 in. in diameter. Thus culm will consist of coal, bony coal, slate, gravel, iron pyrite, etc., ranging in size from 3/32 in. down to dust. Other local terms for culm are " slush," " silt," and " dirt." The first experiments towards the utilization of anthracite culm by briquetting, and the first briquetting-work done in this country, were in 1872 at Port Richmond Piers, Philadelphia, Pa., by E. F. Loiseau.1 Clay was used as a binder and the finished briquette was water-proofed with shellac, etc. Excessive cost was given as the reason for discontinuing work at this plant.

Jan 1, 1912

By D. W. McGlashan, K. N. Mcleod

IN the use of free bubbles with precise temperature control and continuous pH measurement, the contact angle apparatus differs from all previous equipment. Experimental procedures differ sharply from the captive bubble method1,2 of introducing the gaseous phase in the three-phase system. When freed from the tube and captured by a solid surface, a bubble more closely conforms to the spherical ideal set up by the usual mathematical analysis of surface free energy or surface tensional relationships of the forces involved. The assembled equipment, Fig. 1, departs from the usual contact angle apparatus in providing: 1) water circulation for fixing temperature, 2) instruments to measure and record pH during testing, and 3) a system for producing and using free bubbles. The apparatus allows testing over a broad range of closely controlled conditions, and the use of free bubbles gives contact angles independent of operator manipulation, which was unavoidable in the older captive bubble method. A bubble released below the specimen rises through the liquid and contacts the mineral. If the mineral is gas-avid the bubble adheres, developing a finite contact angle. Reaction cells (1), 2x33/8x5 3/16 in. ID, are of pyrex glass 5 mm thick. To prevent optical distortion, the sides are optical flats and are planed parallel to within five wave lengths of light over the entire surface. Special cement is required to withstand chemical attack and thermal shock. The cell is placed in a thermal jacket (2) made of welded aluminum. A water seal for the optical ports is made by using O-rings tightened against the flats of the cell by fine-threaded and adjustable ports, Fig. 2. In-flow water is discharged downward from a manifold located near the bottom of the cell jacket. Water overflows the weirs at each end of the cell jacket, discharging from both sides to a collecting manifold (24). A hose (26) leads the overflow water to the thermal-conditioner well (4), which is recessed to accommodate a reaction cell and two beakers (150 ml). Both the thermal jacket and the thermal-conditioner well are insulated to minimize the effects of temperature differentials. Water, discharging from the thermal-conditioner well, returns to a thermostat bath and pump (3), from which it is pumped to the thermal jacket. The thermostat bath permits temperatures to be adjusted from 1" or 2°C to 80°C and will maintain the selected temperature within 0.2ºC. An electrode support (22) groups the four electrodes (8) so that they fit conveniently into the reaction cell, Fig. 2. This assembly holds the glass electrode, the calomel electrode, the temperature-

Jan 1, 1957

THOSE NOT MARKED ARE MEMBERS; MARKED THUS t ARE ASSOCIATES. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. JUNIOR MEMBERS ARE MARKED II. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. AARONS, J. BOYD, Genl. Mgr., Chaffers G. M. Co., Boulder City, West. Australia. '05 ABADIE, EMILE R., Min. Engr Box 291, Porterville, Tulare Co., Cal. '76 ABBOTT, CLARENCE E., Genl. Supt., Iron Mines Div., 1405 Minnesota Ave., Bessemer, Ala. '04 ABBOTT, J. W., Min. Engr., "St. Omer," 123 N. Grand Ave., Los Angeles, Cal. '94 ABBOTT, Louis BENJAMIN, Chief Engr., Consolidation Coal Co., Elkhorn Div., Jenkins, Ky. '15 ABBOTT, ROBERT R., Met. Engr., Peerless Motor Car Co., Cleveland, Ohio. '12 ABE, ASAKA Yamagano G. M., Satsuma-Gori, Satsuma, Japan. '14 || ABRAHAMS, A. I., Student 1391 Madison Ave., New York, N. Y. '14 tACKER, E. O'C., Met Bethlehem Steel Co., Bethlehem, Pa. '86 ACKER, Louis K., JR., Min. Engr 565 Highland Place, Bellevue, Pa. '08 ADACHI, JINZOO 11 Shiba Park, Shiba-ku, Tokyo, Japan. '88 ADAMI, C. J., Min. Engr., St. Joseph and Doe Run Lead Companies, Bonne Terre, Mo. '12

Jan 1, 1917

By Byron M. Bird

JIGGING is the stratification of a mass of solid particles in upward pulsations of water or in alternating upward and downward pulsa¬tions. The stratification usually is effected in a rectangular open¬top container having a perforated bottom through which the pulsations of water are applied to the materials to be separated; in separating coal, to a mass of coal and refuse. Jigging usually is a continuous process involving three steps: (1) the reception of the raw coal, (91) the stratification of the coal and refuse so that the refuse settles to the screen plate, and (3) the overflow of the cleaned coal and the withdrawal of the refuse collected on the screen. The jig is the most universal washer ever devised. It is handling in practice a wide range of closely sized coals and ores, mixed sizes of coal from 8-in. to 0 through %-in. to 0, and mixed sizes of ores down to %3 O-in. to 0 and even smaller. It is treating materials ranging in specific gravity from that of gold at 19 to that of coal at 1.30. It is handling feeds in which the proportions of high-gravity materials range from 90 per cent or higher, as for some iron ores, to 10 percent or less for some coals. It is handling feeds containing all shapes of particles-round, rectangular, and flat. It is handling simple separation problems and difficult separation problems. Thus, it is an almost universal separating device. One might add that it has been one of the most misunderstood types of washers, from both a theoretical and a practical point of view. Although con¬siderable progress has been made in coal jigging in the past 10 years, the jig probably has more unexplored possibilities than any other type of washer. In this chapter the object has been to treat the jigging process in a practical manner and to give information that will help the reader to improve his particular operation. Inasmuch as performance data from operating plants would contribute little of value, none has been given. Instead, the emphasis is upon jigging principles as a foundation for attacking the problems that arise. These principles are in reality tenta¬tive conclusions from research in the field of jigging during the past 10 years and most of this chapter should be regarded as a progress report on an investigation still under way.

Jan 1, 1943

By M. W. Bartley, Hugh M. Roberts

Substantial deposits of Bessemer hematite have been found recently by drilling beneath Steep Rock Lake, Ontario, which is situated in the northern part of the Lake Superior Region. It will be practicable to divert the waters flowing into this lake and develop open pits on the upper pert of two large ore bodies by damming off and pumping out the water in the part of the lake in which they occur. Ultimately, the bulk of the ore will be mined by underground methods. Owing to the generally massive nature of the rocks in the area, no underground flows of major consequence are anticipated after diversion of the lake. The Steep Rock deposits are attributed in origin to hydrothermal replacement. They were formed, for the most part, along an unconform-able, brecciated contact between the Steep Rock limestone and an overlying younger volcanic series, The replacing solutions came in as igneous after-effects, following upon the intrusion of basic igneous rocks that invaded the hanging-wall volcanics. It is believed that this took place in a geological period roughly equivalent to late Middle Huronian, which was the period when the most extensive iron-bearing rocks of the Lake Superior Region were formed. Comparison is made with other deep-seated iron-ore bodies in the Lake Superior Region, the origins of which are ascribed in the discussion to hydrothermal replacement. Introduction Under the waters of Steep Rock Lake, Ontario, situated on the Canadian National Railway, 142 miles west of Port Arthur, the presence of three ore zones containing red and brown Bessemer hematite has been established. These were discovered and have been partly explored by means of diamond and churn drilling, The positions of the ore zones, designated as A, B and C, are shown on the accompanying maps and cross sections. This exploratory work, begun in 1938 by Joseph Errington* and Julian G. Cross, has been carried on by Steep Rock Iron Mines Ltd., and was continued during the winter of 1941-1942. For more than 60 years explorers have known that large quantities of hard hema. tite float of good grade existed along the south shore of Steep Rock Lake, and the presence of ore beneath the lake was inferred by many early geologists and explorers. Despite numerous previous attempts to find ore in place, actual discovery awaited the recent period of intensive exploratory effort in Canada. The results obtained in the drill holes put down since 1938 by steep Rock Iron Mines Ltd. are not only of interest, in themselves, to those concerned with the development of ore deposits, but, taken in connection with the surface exposures of adjoining formations, they form the assemblage of facts from which the geological reasoning in this paper proceeds; accordingly, they are set out here as briefly and exactly as may be.

Jan 1, 1949

By M. W. Bartley, Hugh M. Roberts

Substantial deposits of Bessemer hematite have been found recently by drilling beneath Steep Rock Lake, Ontario, which is situated in the northern part of the Lake Superior Region. It will be practicable to divert the waters flowing into this lake and develop open pits on the upper pert of two large ore bodies by damming off and pumping out the water in the part of the lake in which they occur. Ultimately, the bulk of the ore will be mined by underground methods. Owing to the generally massive nature of the rocks in the area, no underground flows of major consequence are anticipated after diversion of the lake. The Steep Rock deposits are attributed in origin to hydrothermal replacement. They were formed, for the most part, along an unconform-able, brecciated contact between the Steep Rock limestone and an overlying younger volcanic series, The replacing solutions came in as igneous after-effects, following upon the intrusion of basic igneous rocks that invaded the hanging-wall volcanics. It is believed that this took place in a geological period roughly equivalent to late Middle Huronian, which was the period when the most extensive iron-bearing rocks of the Lake Superior Region were formed. Comparison is made with other deep-seated iron-ore bodies in the Lake Superior Region, the origins of which are ascribed in the discussion to hydrothermal replacement. Introduction Under the waters of Steep Rock Lake, Ontario, situated on the Canadian National Railway, 142 miles west of Port Arthur, the presence of three ore zones containing red and brown Bessemer hematite has been established. These were discovered and have been partly explored by means of diamond and churn drilling, The positions of the ore zones, designated as A, B and C, are shown on the accompanying maps and cross sections. This exploratory work, begun in 1938 by Joseph Errington* and Julian G. Cross, has been carried on by Steep Rock Iron Mines Ltd., and was continued during the winter of 1941-1942. For more than 60 years explorers have known that large quantities of hard hema. tite float of good grade existed along the south shore of Steep Rock Lake, and the presence of ore beneath the lake was inferred by many early geologists and explorers. Despite numerous previous attempts to find ore in place, actual discovery awaited the recent period of intensive exploratory effort in Canada. The results obtained in the drill holes put down since 1938 by steep Rock Iron Mines Ltd. are not only of interest, in themselves, to those concerned with the development of ore deposits, but, taken in connection with the surface exposures of adjoining formations, they form the assemblage of facts from which the geological reasoning in this paper proceeds; accordingly, they are set out here as briefly and exactly as may be.

Jan 1, 1949