Search Documents

By Thomas R. Cunningham, A. B. Kinzel

Silicon, unfortunately, is not in the same category as some other metals with respect to the absolute value of the highest purity material prepared. Tucker, in England, and Becket, in this country have developed procedures for the purification of silicon, and Becket's process has made industrially available silicon of a purity of 99.8 per cent or better. However, even the term "silicon metal" may be a paradox to some people, although not more so than the term "amorphous" as applied to silicon. These terms come from commerce, and "metal" is used to distinguish industrially high-purity silicon from ferrosilicon, silicon-aluminum, and other high-silicon alloys. Alloys of iron and silicon with 95 per cent Si or less are known as ferrosilicon, with a designation of silicon content where necessary, arid the term "silicon metal" is invariably applied to the grades containing 96 per cent Si and higher. The Becket method of purification was referred to in a monograph on the Alloys of Iron and Silicon, and the Tucker procedure was described in some detail in that publication.' In order to get silicon of still higher purity, a sample, prepared by the Becket method, analyzing 99.84 per cent Si, 0.020 Fe, 0.016 Al, 0.005 Ca, 0.025 C, 0.033 per cent 02, 0.006 H2, 0.006 N2, and 0.001 per cent Mn, was crushed to pass a 100-mesh sieve and further purified by a modification of Tucker's procedure. This modification differs from Tucker's method in that after treatment the 100-mesh alloy was centrifuged to remove the last traces of acid. Our directly determined analysis of this purified sample shows: Si, 99.952 per cent; Fe, 0.009; Al, 0.012; Ca, 0.003; C, 0.006; or 99.982 per cent. Silicon by difference equals 99.97 per cent. The variation between silicon by difference and silicon as directly determined is important. Although Tucker mentions the amount of insoluble matter in commercial silicon both before and after his treatment, he does not mention the existence of carbon in the alloy; nevertheless, he reports silicon by difference. Any final figure as to purity obviously results from agreement between direct determination and

Jan 1, 1940

By A. B. Kinzel, Thomas R. Cunningham

Silicon, unfortunately, is not in the same category as some other metals with respect to the absolute value of the highest purity material prepared. Tucker, in England, and Becket, in this country have developed procedures for the purification of silicon, and Becket's process has made industrially available silicon of a purity of 99.8 per cent or better. However, even the term "silicon metal" may be a paradox to some people, although not more so than the term "amorphous" as applied to silicon. These terms come from commerce, and "metal" is used to distinguish industrially high-purity silicon from ferrosilicon, silicon-aluminum, and other high-silicon alloys. Alloys of iron and silicon with 95 per cent Si or less are known as ferrosilicon, with a designation of silicon content where necessary, arid the term "silicon metal" is invariably applied to the grades containing 96 per cent Si and higher. The Becket method of purification was referred to in a monograph on the Alloys of Iron and Silicon, and the Tucker procedure was described in some detail in that publication.' In order to get silicon of still higher purity, a sample, prepared by the Becket method, analyzing 99.84 per cent Si, 0.020 Fe, 0.016 Al, 0.005 Ca, 0.025 C, 0.033 per cent 02, 0.006 H2, 0.006 N2, and 0.001 per cent Mn, was crushed to pass a 100-mesh sieve and further purified by a modification of Tucker's procedure. This modification differs from Tucker's method in that after treatment the 100-mesh alloy was centrifuged to remove the last traces of acid. Our directly determined analysis of this purified sample shows: Si, 99.952 per cent; Fe, 0.009; Al, 0.012; Ca, 0.003; C, 0.006; or 99.982 per cent. Silicon by difference equals 99.97 per cent. The variation between silicon by difference and silicon as directly determined is important. Although Tucker mentions the amount of insoluble matter in commercial silicon both before and after his treatment, he does not mention the existence of carbon in the alloy; nevertheless, he reports silicon by difference. Any final figure as to purity obviously results from agreement between direct determination and

Jan 1, 1940

By Oliver B. Knight

The producing formation in the South Field, or "Golden Lane" structure of Mexico, is a buried ridge of reef limestone of Comanchean age overlain unconformably with sediments of Upper Cretaceous, Eocene and Oligocene. The structure extends in a long sweeping arc, with the convex side toward the west, from San Geronimo, Vera Cruz, to San Isidro, south of the Tuxpam River, which it crosses at the town of Alamo. It is 52 miles long and averages 3/4 mile in width. The surface of the producing formation of El Abra limestone consists of a series of minor parallel highs which are separated longitudinally by synclinal troughs and laterally by structural saddles. The presence of these highs has been of utmost importance in the development of the field, especially in recent years when the salt-water level has risen above the synclines and confined the oil to the isolated highs. In many cases, faulty information and interpretation of the subsurface has resulted in drilling costly dry holes and salt-water wells. Development The development of the Golden Lane was started by the Mexican Eagle Oil Co. in 1906. San Diego No. 3, usually known as Dos Bocas, the first producing well on the structure, was completed on July 4, 1908. This well came in unexpectedly for an estimated daily production of 129,000 bbl., and, as the casing was not properly set, the well flowed wild into the Tamiahua Lagoon, causing a loss of several million barrels of oil. In flowing wild the well formed a crater which covers an area of 48 acres, out of which salt water and small quantities of gas still flow. Casiano No. 2, the Huasteca Petroleum Co., which yielded 200 bbl. of oil daily, and which was completed in November, 1909, was the next producing well to be drilled on the structure. In 1910, the same company completed Casiano No. 7, with an initial production of 50,000 bbl. daily, and Casiano No. 1, which produced 200 bbl. daily. In the same year, the Mexican Eagle Oil Co. completed its Potrero del Llano wells 1, 2 and 4, with initial productions of 500, 400 and 100,000 bbl. respectively. From 3910 to the latter part of 1919, development proceeded

Jan 1, 1931

By W. A. Tiller, W. C. Johnston

The solute distribution ahead of an advancing solid-liquid interface is controlled by varying the momentum boundary layer thickness in the liquid adjacent to the interface. Single pass zone-melting experiments on Pb-Sn alloys are described in which the liquid is caused to rotate in the plane of the solid-liquid interface due to the influence of a magnetic .field rotating in this plane. The variation of the diffusion boundary layer thickness with field strength is determined. DURING the freezing of an alloy a partitioning of solute occurs at the solid-liquid interface, the magnitude depending upon the difference in the solid and liquid solubilities at the interface temperature. Because the diffusion coefficient is so small in the liquid relative to normal freezing rates, either a pileup or a depletion of solute occurs at the interface when the partition coefficient, kO, is either less than or greater than unity, respectively. This solute distribution is completely characterized by i) the solute concentration in the liquid far from the interface, C) the ratio of freezing velocityf, to diffusion coefficient, D, iii) the partition coefficient, ko, and iv) the thickness of the diffusion boundary layer, 6,, at the interface (this assumes that an electric field is not applied across the interface). For a particular system, C ko and D are fixed so that the character of the solute distribution can be changed only by a variation of either f or 6c. As is well known, the freezing velocity can be changed by varying the thermal environment of the alloy. Whereas, the thickness of the solute rich layer can be changed by varying the fluid flow conditions in the liquid. It is the purpose of this paper to describe a technique for controlling the fluid flow conditions in the liquid. During most solidification experiments the driving force for fluid flow arises from either mechanical mixing, thermal convection or electromagnetic mixing. The momentum boundary layer thickness, 6m at the solid-liquid interface, within which negligible movement of the liquid occurs, has been calculated for the special case of mechanical mixing where crystals are solidified by the Czochralski technique.l,2 The calculation of 6m for the case of thermal convection has also been made.3 In some calculations it has been assumed that the momentum boundary layer thickness, 6,, may be equated to the thickness of the diffusion boundary layer 6c, at the interface. However, as may be seen from Appendix I this is only true in very special cases and in general where a is a constant of magnitude determined by the particular liquid alloy. Neither calculations nor experimental data exist for the dependence of upon electromagnetic mixing. In this paper experiments are described in which the liquid is caused to rotate in the plane of the interface due to the torque developed on it by a magnetic field, H, rotating in this plane. The variation of is controlled by the variation of H. A magnetic field rotating in a plane perpendicular to the interface has been used for the purification of aluminum. Experimentally, we determined the variation of 5C with H by using the zone-melting technique of pfann5and a theoretical relationship of Burton et a1.2 pfann5 has shown that, after the passage of one molten zone through a long cylindrical charge of uniform concentration, CO, the solute distribution, C,, in the solid is as shown in Fig. 1. The equation describing this distribution is

Jan 1, 1962

By M. R. J. Wyllie

Eight laboratory-prepared aqueous base drilling muds representing common mud types, and 15 aqueous base drilling muds sampled in the field, have been used in an experimental investigation of the relationship between the streaming potential developed across a mud filter cake and the differential pressure causing filtrate flow. It has been established that the relationship is of the form, ES = kPy, where Es is the streaming potential, P the differential pressure and k and y are constants for any particular mud system at constant temperature. Beyond a certain minimum thickness this relationship is independent of filter cake thickness. Experiment has shown that both k and y are temperature dependent parameters and that in certain mud systems there is a critical value of P above which the simple relationship Es = kPY ceases to hold. The constant k tends to be a function of the mud resistivity at 77ºF, but the exponent y has not been found to be related to any commonly measured mud property. Certain field experiments are described which serve to demonstrate that the total SP (self potential) developed opposite a formation may be quantitatively accounted for as the algebraic sum of an electrochemical potential and an electrokinetic potential. A chart to permit the simple use of mean solution activities in the interpretation of electrochemical SP data is given and its use described. Various field methods for computing the electrokinetic SP component of the total SP are considered and rejected as being unduly complicated and inaccurate. It is shown that the employment of low resistivity drilling muds is essential if optimum accuracy is desired in the use of the S.P. curve for the purpose of computing connate water salinities by the electrochemical SP method. The use of such low resistivity drilling muds is accordingly recommended. INTRODUCTION In a previous paper' a quantitative analysis of the electrochemical compovent of the SP (self potential) curve was made and it was shown that the electrochemical* emf, E, could be expressed as E = ZtRT/F In a,/a,, where t is the transference number of the chloride ion, R is the gas constant, T the absolute temperature of the formation water and mud, a, the mean activity of the connate water (assumed to be sodium chloride) and a, the mean activity of the mud (as sodium chloride). The essential accuracy of this expression was confirmed by an investigation 2 of the SP kicks opposite sands of known water salinity. The logs examined had been routine runs in oil wells in a number of Mid-Continent states. Further confirmation of the original analysis of the electrochemical SP is implicit in the paper by Tixier3 wherein a relationship between the SP and the ratio of connate water and mud resistivities, based only on field data, is given. Allowing for the fact that mud and connate water resistivities were used instead of activities, and that electrokinetic effects were ignored, the constant reported by Tixier is essentially 2tRT/F. The error involved in the universal substitution of resistivities for activities will receive further reference below. Possible reasons for the fact that the electrochemical properties of shales do not appear to be significantly dependent upon either the nature or the quantity of cation exchange materials, such as clays, they contain has been considered at some length by Wyllie and Patnode.4 In the same paper, the probable effects of shale thickness and compaction on electrochemical efficiency, and hence the inherent difficulty of obtaining reliable laboratory-scale data, were also pointed out. However, it is

Jan 1, 1951

By M. R. J. Wyllie

Eight laboratory-prepared aqueous base drilling muds representing common mud types, and 15 aqueous base drilling muds sampled in the field, have been used in an experimental investigation of the relationship between the streaming potential developed across a mud filter cake and the differential pressure causing filtrate flow. It has been established that the relationship is of the form, ES = kPy, where Es is the streaming potential, P the differential pressure and k and y are constants for any particular mud system at constant temperature. Beyond a certain minimum thickness this relationship is independent of filter cake thickness. Experiment has shown that both k and y are temperature dependent parameters and that in certain mud systems there is a critical value of P above which the simple relationship Es = kPY ceases to hold. The constant k tends to be a function of the mud resistivity at 77ºF, but the exponent y has not been found to be related to any commonly measured mud property. Certain field experiments are described which serve to demonstrate that the total SP (self potential) developed opposite a formation may be quantitatively accounted for as the algebraic sum of an electrochemical potential and an electrokinetic potential. A chart to permit the simple use of mean solution activities in the interpretation of electrochemical SP data is given and its use described. Various field methods for computing the electrokinetic SP component of the total SP are considered and rejected as being unduly complicated and inaccurate. It is shown that the employment of low resistivity drilling muds is essential if optimum accuracy is desired in the use of the S.P. curve for the purpose of computing connate water salinities by the electrochemical SP method. The use of such low resistivity drilling muds is accordingly recommended. INTRODUCTION In a previous paper' a quantitative analysis of the electrochemical compovent of the SP (self potential) curve was made and it was shown that the electrochemical* emf, E, could be expressed as E = ZtRT/F In a,/a,, where t is the transference number of the chloride ion, R is the gas constant, T the absolute temperature of the formation water and mud, a, the mean activity of the connate water (assumed to be sodium chloride) and a, the mean activity of the mud (as sodium chloride). The essential accuracy of this expression was confirmed by an investigation 2 of the SP kicks opposite sands of known water salinity. The logs examined had been routine runs in oil wells in a number of Mid-Continent states. Further confirmation of the original analysis of the electrochemical SP is implicit in the paper by Tixier3 wherein a relationship between the SP and the ratio of connate water and mud resistivities, based only on field data, is given. Allowing for the fact that mud and connate water resistivities were used instead of activities, and that electrokinetic effects were ignored, the constant reported by Tixier is essentially 2tRT/F. The error involved in the universal substitution of resistivities for activities will receive further reference below. Possible reasons for the fact that the electrochemical properties of shales do not appear to be significantly dependent upon either the nature or the quantity of cation exchange materials, such as clays, they contain has been considered at some length by Wyllie and Patnode.4 In the same paper, the probable effects of shale thickness and compaction on electrochemical efficiency, and hence the inherent difficulty of obtaining reliable laboratory-scale data, were also pointed out. However, it is

Jan 1, 1951

By R. G. Gifkins

Mean boundary migration depended linearly upon creep extension under various conditions. Prolonged annealing or air-casting increased the proportion of immobile boundaries at a given stage of tests. Grain growth during annealing followed a power law. The linking of migration and sliding in creep and models for migration are examined; activation energies are calculated from these models. Segregation of oxygen to boundaries appears to be a controlling factor. THE idea that boundary migration and boundary sliding during creep are linked has often been suggested,'-5 especially when evidence has been obtained for an alternation between the two processes. In simple bicrystals sliding can occur without any migration6 but in more complex bicrystals7 it is observed. McLean' and Couling and Roberts 5 made measurements of both sliding and migration; McLean concluded that there was no linking of the two processes whereas Couling and Roberts supported the idea. McLean' also developed a model for migration during creep and annealing. The present work was initiated as part of a study of the recrystallization of lead during creep9 but has been extended to examine some aspects of the mechanism of migration. MATERIALS AND METHODS Specially refined high-purity lead* was used; the total of impurities, excluding oxygen, was 0.0008 wt pct. Oxygen was removed as far as possible by melting in vacuo, treating at 550" to 600°C with hydrogen and then casting at 450°C under a vacuum of 10-2 mm Hg; the oxygen was then believed to be 0.00005 wt pct. Specimens were made from extruded strip and then annealed at the required temperature in an air oven, controlled to 5 lac. They were then polished in a mixture of acetic acid and hydrogen peroxide. At this stage some specimens were etched to give grain contrast and their grain sizes determined by the intercept method. Migration of boundaries during creep was measured on the surface of polished (not etched) specimens, directly loaded at room temperature (22°C) or 50°C (52"C) to initial stresses of 300 to 700 1b per sq in. Twenty six vacuum-cast hydrogen-reduced specimens were used and, in addition, two specimens were from material air cast after hydrogen reduction ("partial" air cast) and two from air-cast material not treated with hydrogen ("full" air cast). Duplicates were made in the majority of tests. At intervals through the creep tests, specimens were unloaded and the migration measured, normal to the direction of migration at the point of measurement, for each boundary along standard traverses. Usually between 110 to 180 boundaries were measured at each of some twelve stages of the tests. Migration was measured on the projected image (X100) using prism illumination. Fig. 1 illustrates the method of measurement and shows the kind of variation of migration found from boundary to boundary and along particular boundaries. Fig. 2 gives an example of more extensive migration. The mean value of distance migrated was generally reproducible to *10 pct but occasional points gave a scatter of *20 pct. The correctibn applied by McLean8 to allow for the contribution sliding makes to the apparent distance of migration could not be used, for the sliding at most boundaries was too small to measure with the equipment available. There were two reasons for supposing the correction unnecessary in the present work;

Jan 1, 1960

By C. H. Lee, R. Maddin

The diffusion rates of Ag110 in cylindrical single crystals of 99.99 pct pure silver, which were twisted to a total surface strain of 0.91 during the diffusion anneal at temperatures of 700°, 750°, and 800°C, were measured by sectioning and counting as a function of the strain rates. The ratio of the diffusivities while strain ing occurred (Ds) to those of the unstrained specimens varies linearly with the rate of twisting and attains values of near 100 for some of the rates used. The enhancement of diffusion by straining is inversely proportional to the temperature at which diffusion occurs. The activation energy for diffusion determined from the data plotted as a function of the rate of twisting decreases from 44,090 cal per mole for zero strain, to an asymptotic value of 21,000 cal per mole for the strain rates of 22 x it)"5 see-l. Qualitative explanation for the observations based on the generation of nonequilibrium number of defects by plastic deformation will be discussed. The initial research of Buffington and cohen1 on self-diffusion in a iron under compressive stresses contributed the first quantitative information concerning the effect of applied stresses on diffusion. These results were obtained from radioactive Fe55 plated on one of the horizontal surfaces and compressing the large-grained specimens while the diffusion-anneal was occurring. Enhancement of diffusion of a maximum of seventeen times was observed provided the strain was in the tertiary stage of creep and the rates of straining were at least as fast as rates used in the normal creep test. On the other hand, Darby, Tomizuka, and Balluffi,2 extending silver single crystals up to 30 pct elongation at rates of straining about equal to those used by Buffington and Cohen observed no effect. For the past two and a half years at the University of Pennsylvania, we have been investigating the effect or torsional strains on self-diffusion in silver single crystals. If enhancement is observed as has been reported1 a possible explanation may be based upon the generation of fairly large numbers of point defects and their role in the diffusion process. Hence, since torsion should produce an abundance3 of point defects, an increase in the diffusivity while the crystal is being twisted should easily be measured. EXPERIMENTAL PROCEDURE Our research uses single crystals of silver prepared from 99.99 Ag by the Bridgman method in a dynamic vacuum of less than 25 µ. As grown, they are about 25 cm long by 1.3 cm in diam. The crystals are cut into 7.5 cm lengths with a jeweler's saw and machined to the shape shown in Fig. 1. The test length of the crystal is machined to a 0.6 cm diam after which the ends are masked and the test section etched heavily in HNO3, and KCN:(NH4),S2Os , solution to remove the effects of machining. The specimen is then annealed in vacuum for 8 to 12 hr at 800°C to remove any residual stresses and also to recrystallize the end sections. The recrystallized ends are necessary since experiments showed that single-crystalline end sections are too soft to transmit the desired torque. Occasionally, recrystalliza-

Jan 1, 1960

By J. Chipman, N. J. Grant, R. Rocca

Desulphurization of liquid iron by reducing slags of the electric-furnace type was studied from 65 heats. Variations were made in basicity over a wide range and in FeO up to about 5 pct for their effects on desulphurization. The role of FeO in desulphurization from the blast furnace, to the electric furnace, to the oxidizing conditions of the open hearth is shown to fit a relatively simple pattern of behavior. THE mechanism which controls the desulphurization of molten iron by basic slags has been the object of several investigations. In particular, equilibrium determinations have been made both in the field of basic open-hearth slags, which have a high iron-oxide concentration, and in the field of blast-furnace slags which have a very low iron-oxide concentration. In both cases the desulphurization ratio has been found to increase with increasing basicity of the slags; however, the mechanism of desulphurization differs in the two cases. In basic open-hearth slags desulphurization occurs mainly as a partition of iron sulphide:&apos; FeS * (FeS) and the desulphurization ratio is approximately independent of iron-oxide concentration in the slag. In blast-furnace slags the concentration of iron oxide is very low as a result of the highly reducing conditions in which they are formed. The controlling reaction for desulphurization is then:2,3 FeS + (CaO) <=* (CaS) + (FeO) The slags of the reducing stage in the electric furnace have an iron-oxide concentration which is intermediate between blast-furnace and open-hearth slags. The study of the mechanism of desulphurization for these slags has been the object of this investigation. The importance of low (FeO) in the slag for desulphurization was first verified by Bardenheuer and Geller,& who found that high desulphurization ratios were obtained in highly reduced slags. It was recognized" hat iron oxide in the slag becomes a controlling factor in desulphurization only at FeO concentrations approximately under 5 pct. A recent investigation conducted by Buehl,7 upon the suggestion of one of the authors, confirmed this opinion from the results obtained from a heat conducted in a small arc furnace. In the present investigation, slags of very high basicity, such as often are encountered in the basic electric furnace, could not be studied, but equilibrium data have been obtained for slags in a wide basicity range. The iron-oxide concentration in these slags ranged from 0.08 to 15 pct and was controlled by the addition of silicon to the metal. Other constituents of the slags were mainly CaO, MgO, SiO2, A120,, and CaF,. The experimental technique was essentially the same as that of previous investigations.1 8-lo In an open magnesia-lined induction furnace, 65 lb of Armco ingot iron was melted. An atmosphere of hydrogen was maintained over the melt for 1 hr to bring the carbon content down to approximately 0.010 pct maximum. The bath then was exposed to air for 25 min to remove hydrogen. The electrodes were put in place, and the furnace was operated from this point on in an atmosphere of nitrogen. A synthetic slag was added to which additions of silicon and iron sulphide were made. A rate study conducted at the beginning of this investigation had

Jan 1, 1952

By James T. Waber, Allen C. Larson, Karl Gschneidner, Margaret Y. Prince

The original graphical method proposed by Darken and Gurry for predicting which elements are soluble in a given element was slightly modified and was used to predict terminal solubilities in 1455 known binary combinations. it was found that the modified Darken and Gurry method had a reliability of 61.7 pct in predicting extensive solid solubility (greater than 5 at. pct) and of 84.8pct in predicting limited solid solubility (less than 5 at. pct), an over-all reliability percentage of 76.6. Using the same experimental data, it was found that using only the simple Hume-Rothery size-effect criterion was 50.1 pct reliable in predicting extensive solid solubility, only slightly better than a purely random choice. and 90.3 pct reliable for predicting limited solid solubility, an over-all reliability percentage of 67.6. THE first rational rules for determining a priori whether two metals are not freely soluble in the solid state were announced by Hume-Rothery and coworkers.1,2 These well-known rules have been accorded a special place in metallurgical literature. Since the "electronegative" and "relative valence effect" rules of Hume-Rothery were only qualitative in nature it was difficult to use them in a quantitative analysis. The next major step was made by Darken and gurry3 and apparently went unexplored for a number of years. They prepared graphs illustrating the influence of both electronegativity and size difference on the solubility of elements in silver, magnesium, and aluminum, and they drew elliptical figures, whose maximum width was ±15 pct of the solvent radius and the maximum height was ±0.4 electronegativity units. The purpose of the present paper is to assess and compare the effectiveness of using the simple size-factor and the Darken-Gurry criteria to predict which elements will be soluble and insoluble in a given solute. In 1957, waber4 prepared Darken-Gurry plots for determining the solutes that were likely to be soluble in 6 and plutonium and introduced an inner ellipse as an aid to determining which elements should be soluble to a considerable extent. As illustrated in Fig. 1, the major axis of the outer ellipse corresponded to ±0.4 electronegativity units (OD) while the minor axis corresponded to ±15 pct of the radius of the solvent phase (OB). This simultaneous "action" of the two Hume-Rothery criteria was used to indicate which elements would have little or no solubility in the host lattice, namely those elements whose points lay outside this ellipse. An inner ellipse, "centered" over the same point of the solvent was drawn with ±0.2 electronegativity units (OC) and ±8 pct (OA) as the major and minor axes. Solutes with points lying within the inner ellipse were expected to be capable of forming extensive solid solutions with the host element. Use of this method of applying the earlier Hume-Rothery criteria was moderately successful for plutonium. For 6-phase plutonium, only one element out of the eight predicted to be extensively soluble was known to be almost insoluble, and of the sixteen elements predicted to have more restricted solubility, five were known to be essentially insoluble. The success of discerning solubility in the E phase by this method was comparable. One prediction made on the basis of this analysis was that the heavier rare earth metals, such as holmium, erbium, and thulium, should be soluble in the 6 phase, whereas the lighter rare earth elements, such as lanthanum or

Jan 1, 1963

By L. J. Kashar

By means of a continuum-mechanics approach, the following equation for calculuting the pressure for axisymmetric cold forging has been derived: where P is the extrusion pressure; K and n are the strength coefficient and the strain-hardening exponent of the steel, respectively; a and b are strain factors, primarily dependent on the die design; and R is the extrusion ratio. Data from compression and backward-extrusion tests performed at a crosshead speed of 0.5 in. per min on a nonwork-hardening material pure lead) and on a work-hardening material (1018 steel) indicate that the predicted extrusion pressures obtained from the derived equation agree very closely with the actual extrusion pressures. Therefore, the equation can be used to predict backward-extrusion pressures from standard mechanical-test data. The decision to cold-forge a part is based on several considerations, most of them related to economics. However, the production feasibility is usually determined by the pressure needed to extrude the part and the availability of tooling that can repeatedly sustain this pressure for over several hundred thousand cycles. A major contribution to the cold forging of steel would result from the development of steels that could be forged at reduced pressures and from the development of techniques that permit the accurate prediction of the pressure necessary to cold-forge the part. The ability to predict extrusion pressures is necessary to properly design the tooling required for the cold-forging process. Attempts to theoretically predict the cold-forging pressure, especially for work-hardening materials, have been unsuccessful in previous investigations of the cold-forging process.1-3 Many empirical relations have, therefore, been proposed relating the extrusion pressure to the chemical composition,&apos; the extrusion ratio,2 the tensile strength,273 and hard- ness, 2 and the yield strength3 of the material being extruded. However, these empirical relations are valid only for the specific conditions used in their development, and, in some cases, the empirical relations had a scatter band greater than * 10 pct. A study of the extrusion process was undertaken with the objective of developing predictor equations for extrusion pressure by using a continuum-mechanics approach to the problem of metal flow. The derivation of such an equation is summarized in this paper, and data are presented that confirm the validity of the derived equation. DERIVATION OF THE EXTRUSION EQUATION If the extrusion of a material through a die is considered in terms of a work balance, it has been shown that it is possible to derive an equation relating the work necessary to move the material through the die to the deformation work undergone by the material. The work done, W, in moving the material is given by where F is the extrusion force, I, is the distance the material was moved, A, is the original cross-sectional area of the material, P is the extrusion pressure acting on A,, Ap is the cross-sectional area of the extrusion punch, and Pp is the punch pressure acting on Ap. The deformation work, WD, is given by where V is the volume of metal deformed, ay is the flow stress of the metal, and E is the total strain undergone in the extrusion. If there are no frictional losses, the work done, W, is equal to the deformation work, WD; therefore, Since the volume of a metal does not change during deformation,

Jan 1, 1968

By C. D. Cochran, F. H. Deily, M. M. White, Victor Horner

A laboratory study of the effects of physical and easily measured rheological properties upon dynamic filtration was carried out. The purpose was to determine the factors affecting dynamic filtration and thus learn how to control this important property. The recommended procedure for determining the amount of fluid loss prescribed by API Code RP 29 "Field Procedure for Testing Drilling Fluids,"&apos; is very useful for mud conditioning purposes, but inadequate for comparing filtration properties of different muds under dynamic conditions. Where dynamic filtration control becomes important for purposes such as logging and coring, other means of evaluating filtration properties are needed. A special device and testing technique were developed to provide reliable data on filtration characteristics of different fluids under dynamic conditions. Liquid saturated rock samples were drilled with a microbit, and the amount of connate liquid displaced by the fluid being investigated was measured. The empirical testing procedure was considered reliable. A large number of laboratory-prepared and field-mixed dritling fluids with a wide range of physical properties were studied. These properties included: (I) shape of consistency curves, (2) apparent viscosity, (3) plastic viscosity, (4) yield value, (5) density, and (6) API filter loss. Test results indicate that very little, if any, trend could be established between changes in these fluid properties and dynamic filtration. INTRODUCTION During the process of drilling, excessive loss of liquid from the mud to the formation is undesirable for many reasons. Filtration can reduce production-zone permeability, cause sloughing of formations, affect electric log curves, and render the fluid data obtained from cores unreliable. Thus, it is very important that we gain a knowledge of the factors that control filtration. It is generally agreed that in any type of filtration (static, dynamic, or combinations thereof), the mechanics of filtering depend in great part upon the composition of the fluid. Moreover, it is also true that the physical and rheological properties are influenced by the composition of the fluid. Indirectly, then, it was hypothesized that a relationship existed between dynamic filtration and physical-rheological properties, two effects of a common cause—fluid composition. This paper discusses an attempt to relate filtration-while-drilling to physical and easily measured rheological properties. It is believed that the results of this study may prove useful to others in the industry who are working on the problem of understanding filtration. The industry accepted practice for determining fluid loss from drilling mud is described in API Code RP 29. The practice is to measure the amount of filtrate that passes during a given interval of time from a quiescent drilling fluid under applied pressure through a piece of filter paper. This is primarily a test of static filtration properties. Other investigators have studied filtration under dynamic conditions. Williams5 and Pro-kop5 studied radial filtration and filter-cake buildup by circulating fluid through a porous cylinder under conditions similar to actual mud flow. Nowak,4 Krueger,3,4 and Vogel3 studied the effect of filtration upon permeability by flowing mud past the face of rock Samples. In their tests, the bit action was simulated by mechanical scrapers that kept the filter cake from building up. Ferguson and Klotz2 studied three types of filtration: static, dynamic, and beneath-the-bit. They investigated each type separately, using a model well in which bottom-hole hydraulics and mechanics were closely approximated.

Jan 1, 1958

By E. L. Kamen, H. D. Kessler, M. Hansen, D. J. McPherson

The highly reactive Ti-Mo and Ti-Cb alloys were prepared and heat treated under protective conditions. Phase diagrams were established based on micrographic and X-ray diffraction analysis and detection of incipient melting. ß titanium forms a continuous series of solid solutions with both molybdenum and columbium, whereas these metals are only slightly soluble in the a titanium modification. PREVIOUS work on the Ti-Mo and Ti-Cb systems was very limited and is discussed in succeeding sections of this paper relating to the respective phase diagrams. The diagrams in the present work were determined principally by micrographic analysis, because other methods such as thermal analysis and dilatometry are not suitable, due to the low diffusion rates of these alloys in the transformation range. X-ray analysis was believed less useful than micrographic analysis because: 1—On quenching certain high titanium alloys from above their transformation range, the body-centered cubic ß phase decomposes into acicular a (hexagonal close-packed) which room temperature X-ray diffraction techniques cannot differentiate from isothermal a. 2— High temperature X-ray techniques might be used, but are difficult to apply and are subject to error because of the high reactivity of titanium with gases such as oxygen and nitrogen. Although metallo-graphic study was the basic method used, X-ray diffraction analysis was applied to a limited extent, to further substantiate the findings. The transformation ranges on the titanium side of the Ti-Cb and Ti-Mo systems were studied both with DuPont Process A (magnesium-reduced) titanium alloys and with iodide titanium alloys. The Process A metal was used chiefly to bracket the transformation range in order to reduce the number of alloys given a particular treatment for the more accurate final study with iodide titanium alloys. Experimental Procedure The analyses of the metals used in the preparation of alloys for this study are presented in Table I. Melting Practice: Early in the work, a consumable electrode, arc melting furnace was used in the preparation of the Process A Ti-base Mo and Cb alloys. This type of furnace has been described by other investigators.&apos;, &apos; One of the major difficulties of the consumable electrode melting process was the prep- aration of homogeneous electrodes (with the mixture of coarse titanium sponge and fine powder alloying addition) which would give homogeneous ingots. Composition gradients encountered may have been due to a tendency for powdered alloying metals to drop away from the electrode in handling. This difficulty in the preparation of homogeneous alloys was overcome by the use of a nonconsumable electrode furnace for later work. This furnace is similar to the one used by Mc-Pherson and Fontana a Ohio State University. A diagram of the nonconsumable electrode arc furnace is given elsewhere.&apos; The source of power was a 400 amp dc welding generator. Electrode tips of tungsten (% in. in diam) were used for all columbium melts and for a limited number of molybdenum melts. Molybdenum tips were used for the majority of molybdenum alloy melts. Columbium tipped electrodes were tried, but disintegrated rapidly at currents above 300 amp. In the Process A titanium melting practice the metals were charged into the water-cooled spun copper crucible in the following forms: l—titanium: sponge (—4 + 16 mesh); 2—molybdenum: sections of 0.003 in. sheet (approximately ½ in. sq); and 3— columbium: powder compacts (? in. lumps broken from large section). After alternately evacuating and purging the furnace several times with argon or helium, the arc was struck against the metal charge,

Jan 1, 1952

INTRODUCTION Trade financing is a particularly important component of short-term financing for a minerals company since errors, extra costs, or payment delays/defaults can easily wipe out the profit margin on a particular shipment or can cause problems when arranging purchases of e.g. reagents. It is required to make any minerals operation function and does not have to be cross-border to require proper management. Sources of working capital are as follows: 1. Extended credit terms from suppliers 2. Inventory loans from banks, finance companies 3. Accounts receivable financing or factoring 4. Credit lines or overdraft facilities from banks. TRADE CREDITS These are provided under the familiar terms "net 10 days" or payment due by the "10th day of the following month." Thirty days for payment is usual but longer periods can be negotiated with regular suppliers. Shipment may be made on open account with specified periods for settlement. In the mining industry, a custom smelter gains trade credit by paying for concentrates three months after the month of shipment. INVENTORY LOANS Various forms of inventory finance are provided via "floor-plan" or warehouse financing. A set percentage, usually 60%-80%, of a good-quality, readily saleable inventory item (e.g. bullion, concentrates, ingots) will be provided by a bank or finance company which will usually have security over these products and has a right to inspect the goods from time to time. Legal security will he achieved by warehouse receipts, floating liens, chattel mortgages, trust receipts, or through collateral management service companies. The latter certify control over stock or distribution outlets and often carry insurance against fraud. Costs range around 1.5% - 2.0% p.a. or more plus some fees to cover out-of-pockets or other costs. ACCOUNTS RECEIVABLES Accounts receivable financing is based on the company&apos;s generation of satisfactory receivables which are continuously assigned to a bank or finance company ("factoring"). Because of the risks in being able to collect receivables, such as payments to a smelter for its blister copper shipments to a refinery, this form of financing costs as much as 3% - 5% of the debt amount purchased plus an additional charge for processing paperwork. Receivables can be purchased with or without recourse and on a notification or non-notification basis to the client&apos;s customer to, respectively, pay the invoice directly to the bank or not. LETTERS OF CREDIT Letters of Credit ("L/C&apos;s") are a common feature of international trade finance whereby a bank, at the request of the buyer, issues a written undertaking to an exporter to pay a specified sum of money within a set time on presentation of previously specified documents. This undertaking means that the exporter is no longer relying on the credit standing and integrity of the foreign importer. A dispute about shipment does not otherwise affect the obligation to pay upon presentation of a "clean" set of documents. These documents include the hill of lading and other documentation, often on standard "form" bases. There are a number of conventions and techniques in L/C&apos;s such as irrevocable/revocable L/C&apos;s, time L/C&apos;s, confirmation/advising L/C&apos;s and transferable L/C&apos;s. These are tools to adjust for the varying risks that the importer will not pay. Other routes where one is comfortable with an importer include documentary sight hills (D/P hill), documentary term bills (D/A bill), and, of course, open account.

Jan 1, 1985

By B. C. Wonsiewicz, G. Y. Chin

THE presence of deformation bands in cold-worked metals is known to influence the development of deformation textures1 but has not been considered in any theoretical treatments. At the present time the most rigorous theory of deformation textures appears to be based on Taylor&apos;s concept of homogeneous deformation of a crystal within a polycrystalline aggregate.&apos; For each crystal the Taylor theory allows the operation of several equivalent combinations of five or more slip systems. Hence deformation bands can arise from the operation of a separate combination of slips in each of several portions within a crystal. On the other hand, a second type of band may occur as a consequence of slip on systems other than those selected on the basis on homogeneous deformation. This type appears to be associated with crystals of symmetrical orientations, such as the [loo] and [lll.] axial orientations in drawn wires of fcc single crystals studied by Ahlborn.3 In this note we propose a simple mechanism of deformation banding of the second type, and compare the theoretical results for wire drawing of [loo] and [Ill] with Ahlborn&apos;s observations. In outlini the model requires that the work to accomplish a given overall shape change by banding be less than or equal to the work to accomplish the same change by homogeneous deformation. While the work by homogeneous deformation, WH = ?T ;dri, can be calculated exactly by the equivalent methods of Taylor2 or of Bishop and Hill,4 the work by banding, WB, is less certain. The latter consists of 1) Wi, work by slip within a band, 2) Wb, work associated with formation of a boundary between bands, and 3) Wc, work to correct the difference in shape change arising from banding and homogeneous deformation. The Wi term can be evaluated explicitly for a band with an assumed set of slip systems, but a satisfactory analysis of Wb and Wc has not been obtained. Since WB = Wi + Wb + Wc WH, for banding to occur, however, a necessary condition is Wi = WH . Hence it seems reasonable to choose a band with the lowest value of Wi among competing bands consistent with Wi = WH, and then minimize Wb and Wc by arranging the physical configuration of the selected band. Wc is minimized by combining neighboring bands such that their net strain matches the macroscopic strain as closely as possible, and Wb is minimized by enforcing strain compatibility across the boundary between two neighboring bands, similar to the case of a grain boundary.5 It is realized that this procedure is not completely satisfactory, but it does seem to explain Ahlborn&apos;s observations reasonably well. The procedure is now outlined for the two corner orientations. a) [l00]. Fig. 1 shows a (100) stereographic projection. The results of the Taylor analysis for axi-symmetric flow by homogeneous deformation6 show that, while [loo] itself is unstable, the rotation of the tensile axis will nevertheless be confined to within about 15 deg from [loo]. Alternatively, less work may be expended by banding with slip on a pair of systems with primary-conjugate relationship, e.g., (ll1)[10l.I + (li1.)[110]. The latter represents minimum Wi for all possible bands.* Since there are four symmetrically

Jan 1, 1970

By D. J. Schmatz

DISCUSSION OF RESULTS The qualitative correlation between low-temperature ductility and prior high-temperature creep strain in nickel obtained in this investigation confirms the result obtained on high-purity brass by Chen and Machlin. However, the quantitative effect is much smaller in nickel. Comparison can be made on the basis of a prior high-temperature strain that is a certain percentage of the total high-temperature elongation to rupture. In the research of Chen and machlin, the prior high-temperature strain of 1/2 pct equaled 8.5 pct of the total high-temperature elongation at rupture. For nickel, in our experiments, 8.5 pct of 21.2 pct equals 1.8 pct. For eh = 1.8 pct, the loss in ductility in percent equals x 100 = b.5 pct. That is, for equivalent bo Formation of Beta Manganese-Type Structure in Iron-Aluminum-Manganese Alloys D. J. Schmatz IRON-aluminum alloys have gained much interest in the past few years for use as a base material for elevated-temperature alloys because of their excel- high-temperature strain the loss in low-temperature ductility is 8.5 pct for nickel as compared to 60 pct for pure a, brass. It is also interesting to note the observation that in nickel the low-temperature fractures, even at the most extreme high-temperature pre-strain, were partly trans crystalline and partly intercrystalline. In the case of a brass, these fractures were completely intercrystalline. According to the data on the percent of the grain boundary area that is cracked, at 22 pct high-temperature elongation, about 12.5 pct of the grain boundary area does not carry load. Thus, the inter-crack areas are carrying a stress that is about 11 pct higher than the nominal stress. A simple model predicts that the overall elongation, which is primarily the elongation in the bulk of the specimen, will correspond to the nominal stress when the stress in the intercrack area equals the tensile strength. Quantitatively this model predicts the equation The form of this equation will agree with that found if the strain-hardening exponent, n, equals unity. Actually this model is too gross an approximation to yield good quantitative results. The question naturally arises as to whether in ordinary hot-working, such as hot-rolling, intercrys-talline cracks are introduced that affect the low-temperature properties. It appears that the answer is that such a possibility cannot be overlooked, if the hot-working induces tensile stresses at temperatures above the equicohesive temperature and if the material tends to be notch sensitive at low temperature. ACKNOWLEDGMENT This research was supported by the Aeronautical Research Laboratory, Directorate of Research, Wright Air Development Center, United States Air Force. REFERENCES lC. Zener: Fracturing of Metals, 1948, Cleveland, ASM. &apos;H. C. Chang and N. J. Grant: Mechanism of Intercrystalline Fracture. AIME Trans., 1956, voL 8, p. 544; lownal of Metals, May, 1956. &apos;E. S. Machlin. CreepRupt ure by Vacancy Condensation, AIME Trans., 1956, vol. 8, p. 106; lownd of Metals, February, 1956 &apos;C. Chen and E. S. Machlin: On a Mechanism of High-Temper at ure Inter-crystalline Cracking, lownd of Metals, July. 1957. p. 829. Alloys lent oxidation resistance. Binary alloys of aluminum in iron are ferritic and consequently have poor hot strength. Alloys of iron-aluminum-manganese were made in an attempt to produce an austenitic alloy containing sufficient aluminum to retain the oxidation resistance of binary alloys of iron-alumi-

Jan 1, 1960

SEC. 1. The membership of the Institute shall comprise seven classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6. Rocky Mountain Members; 7. Junior Foreign Affiliates. All shall be equally entitled to the privileges of membership, excepting that no member of any class whose residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the class of Member must be at least 27 years of age and must have had at least six years&apos; employ¬ment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members. SEC. 3. Honorary Members: Each candidate for Honorary Membership must be recommended by at least ten Members and must be elected by ballot at a meeting of the Board of Directors by the unanimous vote of the Directors present; provided, how¬ever, that the number of Honorary Members shall at no time exceed twenty. Such election shall automatically act as a transfer of such member from any other class of membership to which he may belong. SEC. 4. -Senior Members: The Directors may in their discretion place on the Honor Roll of Senior Members and transfer from any other class of membership other than Honorary Membership the name of any Member or Associate who has reached the age of seventy years and who has paid dues for thirty years, and for good reasons in special cases may vary the age or number of years. SEC. 5. Junior Members: A person to be eligible for election to the class of Junior Member must be qualified through education or experience to hold a subordinate position in engineering, mining, metallurgical, geological or chemical work. He shall be not more than 33 years of age at the time of election. SEC. 6. Associates: A person eligible for election or transfer into the class of Associate shall be one, who, in the opinion of the Committee on Admissions and the Board of Directors, is suitable for such election or transfer by reason of his interest in or connection with mining, geology, metallurgy, or chemistry. SEC. 7. Rocky Mountain Members: Membership in a special class of life member¬ships without annual or other dues and without right to receive the printed literature distributed to other members or the right and privilege of wearing the official badge of technical members, is given to all members of the Rocky Mountain Club at the time of consolidation. These special Rocky Mountain memberships shall be claimable by any member of the Rocky Mountain Club, not already a member of the Institute, availing himself of the privilege within ninety days after mailing of notice to him, by the Secretary of the Institute. SEC. 8. Junior Foreign Afliate: Upon appropriate action by the Board of Direc¬tors and with its approval, members in good standing of any technical society having its headquarters outside of the United States of America, Canada, or Mexico,

Jan 1, 1937

By S. F. Ravitz, S. R. Zimmerley

High-grade cobalt concentrates were produced from the complex Blackbird ore with very good recovery in continuous pilot-plant operations in which a low-grade bulk cobaltite-pyrite flotation concentrate was roasted in a multiple-hearth furnace to oxidize the pyrite selectively. The cobaltite was floated from the resulting calcine. THE existence of the cobalt-copper deposits in the Blackbird district, Lemhi County, Idaho, has been known for many years. However, these deposits have not yet been exploited successfully because of the low grade of the ore, absence of information on ore reserves, and lack of feasible methods for concentrating and recovering cobalt from the ore. In 1941, when it appeared that World War II might interfere seriously with imports of cobalt from overseas, the U. S. Bureau of Mines started an extensive mining and metallurgical investigation of the Blackbird deposits. Exploration by trenching and drilling1 indicated that ore reserves were adequate to warrant consideration of large-scale exploitation. A process for producing high-grade cobalt concentrates from the ore was developed at the Salt Lake City Station of the Bureau,2 and hydrometallurgical procedures for producing cobalt metal or oxide from the concentrates were developed at the Boulder City Station.3 The Howe Sound Co., through a subsidiary, the Calera Mining Co., carried out further exploratory work, which increased probable ore reserves to a tonnage commensurate with a large investment in mine, mill, transportation facilities, and refinery. Simultaneously, the metallurgical staff of the company, working in cooperation with the Bureau of Mines, further investigated the metallurgical problems. It was the opinion of both groups that pilot-plant testing was required to translate laboratory results into plant operation. In general, the Blackbird ore has a high content of pyrite and some pyrrhotite and contains 0.5 to 1 pet cobalt and 1 to 2 pet copper, which are present essentially as cobaltite and chalcopyrite. The copper can be recovered readily as a high-grade concentrate by selective notation. The cobalt then can be recovered as a bulk sulphide concentrate assaying 4 to 5 pct cobalt, but no satisfactory procedure for separating the cobalt from the pyrite and pyrrhotite directly by flotation had been found. The method developed by the Bureau for producing a high-grade cobalt concentrate is essentially an application of the old Horwood process of selective roasting.4 The bulk sulphide concentrate is roasted to form an oxide coating on the iron mineral particles, and the calcine is then treated by flotation. The oxide coating prevents the iron minerals from floating so that it is possible to obtain a high recovery of cobalt in concentrates assaying more than 20 pct cobalt. Laboratory tests by metallurgists of both the Bureau and the Howe Sound Co. had indicated the optimum roasting temperature to be 425° to 450°C. At lower temperatures the rate of oxidation of the iron minerals is too low, whereas at higher temperatures substantial quantities of cobalt are rendered water-soluble. Because of its high sulphur content (35 to 40 pct), the bulk concentrate tends to continue to burn after it has reached the optimum roasting temperature. Although excessive temperatures could be avoided in the small-scale laboratory furnaces, there was considerable doubt that the temperature could be controlled properly in industrial equipment. To provide material for the pilot-plant tests, the Calera Mining Co. installed a small, temporary flotation mill at the Blackbird property and treated

Jan 1, 1951

By S. R. Zimmerley, S. F. Ravitz

High-grade cobalt concentrates were produced from the complex Blackbird ore with very good recovery in continuous pilot-plant operations in which a low-grade bulk cobaltite-pyrite flotation concentrate was roasted in a multiple-hearth furnace to oxidize the pyrite selectively. The cobaltite was floated from the resulting calcine. THE existence of the cobalt-copper deposits in the Blackbird district, Lemhi County, Idaho, has been known for many years. However, these deposits have not yet been exploited successfully because of the low grade of the ore, absence of information on ore reserves, and lack of feasible methods for concentrating and recovering cobalt from the ore. In 1941, when it appeared that World War II might interfere seriously with imports of cobalt from overseas, the U. S. Bureau of Mines started an extensive mining and metallurgical investigation of the Blackbird deposits. Exploration by trenching and drilling1 indicated that ore reserves were adequate to warrant consideration of large-scale exploitation. A process for producing high-grade cobalt concentrates from the ore was developed at the Salt Lake City Station of the Bureau,2 and hydrometallurgical procedures for producing cobalt metal or oxide from the concentrates were developed at the Boulder City Station.3 The Howe Sound Co., through a subsidiary, the Calera Mining Co., carried out further exploratory work, which increased probable ore reserves to a tonnage commensurate with a large investment in mine, mill, transportation facilities, and refinery. Simultaneously, the metallurgical staff of the company, working in cooperation with the Bureau of Mines, further investigated the metallurgical problems. It was the opinion of both groups that pilot-plant testing was required to translate laboratory results into plant operation. In general, the Blackbird ore has a high content of pyrite and some pyrrhotite and contains 0.5 to 1 pet cobalt and 1 to 2 pet copper, which are present essentially as cobaltite and chalcopyrite. The copper can be recovered readily as a high-grade concentrate by selective notation. The cobalt then can be recovered as a bulk sulphide concentrate assaying 4 to 5 pct cobalt, but no satisfactory procedure for separating the cobalt from the pyrite and pyrrhotite directly by flotation had been found. The method developed by the Bureau for producing a high-grade cobalt concentrate is essentially an application of the old Horwood process of selective roasting.4 The bulk sulphide concentrate is roasted to form an oxide coating on the iron mineral particles, and the calcine is then treated by flotation. The oxide coating prevents the iron minerals from floating so that it is possible to obtain a high recovery of cobalt in concentrates assaying more than 20 pct cobalt. Laboratory tests by metallurgists of both the Bureau and the Howe Sound Co. had indicated the optimum roasting temperature to be 425° to 450°C. At lower temperatures the rate of oxidation of the iron minerals is too low, whereas at higher temperatures substantial quantities of cobalt are rendered water-soluble. Because of its high sulphur content (35 to 40 pct), the bulk concentrate tends to continue to burn after it has reached the optimum roasting temperature. Although excessive temperatures could be avoided in the small-scale laboratory furnaces, there was considerable doubt that the temperature could be controlled properly in industrial equipment. To provide material for the pilot-plant tests, the Calera Mining Co. installed a small, temporary flotation mill at the Blackbird property and treated

Jan 1, 1951

By William B. Plank

IN my studies during the past twenty years of the enrollments in the mining and metallurgical schools of the United States and Canada, I have been struck with the great diversity in the curricula offered by these schools. In 1933 when I made my first complete study of the schools (Mining and Metallurgy, May 1934, p. 211), I discovered 19 different curricula or programs of study, leading to almost as many different bachelor degrees, in the 49 schools in the United States and the 4 schools in Canada. These were: (1) Mining Engineering, (2) Coal Mining, (3) Metal Mining, (4) General Mining, (5) Mining Administration, (6) Mining and Metallurgy, (7) Metallurgical Engineering, (8) Metallurgy, (9) Petroleum Engineering, (10) Petroleum Refining, (11) Petroleum Geology, (12) Petroleum and Natural Gas, (13) Ceramic Engineering, (14) Ceramics, (15) Geological Engineering, (16) Mining Geology, (17) Economic Geology, (18) Geo- physics, (19) Fuel Technology.

Jan 3, 1950