Search Documents

By C. Ernest Birchenall

AS a basis for further progress in several branches of metallurgy, particularly the study of physical properties of solid solutions and the kinetics of solid-solid reactions, a more complete understanding of the structure of solid solutions and the nature of the metallic bond is- necessary. Any investigation contributing to this understanding should be of primary interest to the metallurgist. Since the metallic bond is characteristic of an assemblage of atoms, it can be studied only where this assemblage exists. One of the most promising approaches to this study of the interactions in metals is through the general problem of binary metallic solutions. Although crystal structures of many solid metallic solutions have been determined and solubility limits for many systems are given in phase diagram studies, progress beyond this is irregular. Electromotive force and vapor pressure determinations have provided thermodynamic activity data for small concentration and temperature ranges in the amalgams and a few other systems.' In two systems, however, copper-zinc and iron-carbon, data are available for the calculation of activities over wide ranges of temperature and concentration. This activity data for the brass system is summarized in the preceding paper.= A detailed study of the solubility and distribution of carbon in iron is given by Smith and Darken.3 Their treatment of interaction energies is applicable only to dilute interstitial solutions. The objectives here will be to derive from activity gats given in the previous paper for the brasses and structural considerations as much new and detailed information as possible about the interactions between copper and zinc in metallic solid solution and the effect of these interactions in determining the short range structure of the equilibrium phases; that is, we shall investigate the energy of interaction between pairs of atoms of the same and different kinds, the deviations of the distribution of nearest neighbors from complete randomness, and show that the conclusions found are consistent with the observed behavior of the brass system. The method of treatment is fairly general for substitutional metallic solid solutions and will be applied to other systems. The determination of vapor pressures of the components of alloy systems is being undertaken in this laboratory to supply more data for this purpose. The information obtained from solid solutions may be extended by careful analogy to liquids as long as the metallic type of bonding is preserved. Since it will be necessary to employ the language of thermodynamics, a brief summary defining the terms used extensively in solution theory is given below. Solution Theory4 An ideal solution is one in which the vapor pressure of the constituent molecules

Jan 1, 1947

By C. D. Stahl, S. M. Farouq Ali, W. E. Culham

One- and two-dimensional mathematical models have been developed that simulate transient, two-phase flow of hydrocarbon mixtures in porous media in a manner that accounts for interphase mass transfer. Numerical simulations of one-dimensional depletion-drive experiments using a two-component hydrucarbon fluid were used to establish the validity of the mathematical models. In addition, the experimental and numerical data were used to demonstrate that production rate had a relatively insignificant effect on the recovery of individual hydrocarbon components from the experimental system, and that attainment of equilibrium between phases is possible for a wide range of liquid and vapor velocities in reservoirs containing light hydrocarbon fluids. Results of some two-dimensional numerical simulations are also presented. INTRODUCTION This study was undertaken to develop a mathematical model that would simulate transient, two-phase flow of hydrocarbon mixtures in porous media under conditions that result in interphase mass transfer and to test the validity of the assumptions used to set up the model. In addition, the study was designed to determine if production rate influences the recovery of individual hydrocarbon components from reservoirs producing by depletion drive. Two-phase flow in porous media, with interchange of components between the two phases, is important in many petroleum recovery processes. Studiesl-5 conducted within the last 3 years have outlined methods of solving multiphase flow problems incorporating mass transfer. Some of these studies have also indicated the importance of accounting for mass transfer under various producing conditions. An earlier work6 first demonstrated the importance of combining relative permeability data with equilibrium ratios in compositional balance methods. The mathematical model presented in this paper is formulated so that a phase behavior package, as described in previous papers,5,17 is not required as an integral part of the routine employed to solve for the primary dependent variables. The finite difference formulation is designed so that all the primary variables can be solved for simultaneously. This is accomplished by utilizing one basic set of equations. These innovations, which are in contrast to other models2,3,5 but are similar in some respects to the approach used by Taylor,l render the total problem computationally simpler than any of the previously referenced formulations. The mathematical model was developed by combining Darcy's law with a continuity equation for each hydrocarbon component. The principal assumptions invoked in the formulation were (1) that capillary forces and diffusional effects are negligible, and (2) that thermodynamic equilibrium exists in the reservoir at all times. No assumption as to the type of vaporization process was made in formulating this model. Experimental data were required to complete this study. These were generated by conducting several depletion drive experiments. The experimental apparatus consisted of a sandstone core enclosed in a pressurized casing. The apparatus was designed in such a manner that the core could be charged with a liquid hydrocarbon mixture and depleted at different production rates. The experimental tests were designed to determine the effect of production rate on component recovery. In addition, direct comparison of experimental and mathematically predicted

Jan 1, 1970

By J. H. Faulk

An examination is made of the various factors influencing drilling rate and drill bit life in various diameter holes. It is concluded that drill bits in the size range 4% to 6 1/4 in. can be used to attain substantially the some daily drilling progress as conventional size bits in soft rock drilling operations. An examination of the most important factors influencing "hazard of losing the hole" in the different hole size results in the conclusion that the smaller hole sizes can probably be drilled at reasonably low risk. However, this risk will be somewhat greater in the smaller diameter holes, requiring that special drilling and mud engineering practices be used to make small diameter holes practicable in soft rock drilling operations. An engineering analysia is made of the power and hydraulic requirements of several drill string-hole combinations to test the feasibility of drilling .small diameter holes in soft rock areas. Large econormies in rig power requirements appear possible by drilling .smaller .size holes in these operations. INTRODUCTION The industry now is re-examining the utility of small diameter holes in the light of substantial technical advances made in recent years. Faced with increasing cost of finding reserves and with proration after developing them, the industry must either develop methods of economizing or receive a lower rate of return on investments. Small diameter holes appear to involve an attractive method of economizing. Our objective is to determine if this is technically possible in soft rock operations. Soft rock, as used in this report, refers to those formations of a "drill-ability" corresponding to that of all Gulf Coast formations shallower than and frequently including much of the Eocene rock system. An important phase of technology which we shall examine is relative drilling rate and bit footage which may be obtained with various size bits. Rig operating efficiency, particularly as influenced by hazard, is also discussed in detail. The technical conclusions resulting from these examinations are used to develop sample drill string design and rig horsepower requirements for drilling holes as smaH as 4 3/4 in. and larger. The principal criterion used for the drill string design is that approximately the same daily drilling progress would be possible in all size holes in soft rock operations. This facilitates a comparison of rig size required for drilling the hole sizes in the range between 4 3/4 and 8 3/4 in. BROAD PROBLEM OF DRILLING RATE AND BIT FOOTAGE The three factors controlling daily drilling progress are: (1) drilling rate of bit while on bottom turning, (2) bit footage, and (3) rig operating efficiency. Let us look now at the first two of these factors. Drilling technology has progressed to the point that a semi-quantitative analysis of the effect of various operating variables upon these factors can be made. Those factors which apparently limit both drilling rate and bit footage for bits now in use are: (1) bit design, (2) weight on bit, (3) hydraulic cleaning capacity for bit cutting surfaces and hole bottom, and (4) rotary speed. (We neglect the effect of mud and formation properties because these factors arc the same for the various size bits.

Jan 1, 1957

By W. N. Hiatt

The mathematical theory of the flow of two-phase, incompressible fluid through porous media is clarified, and the development of a general fluid displacement equation for two-phase, incompressible vertical flow through porous media is outlined. The relationship between the three components of the equation — the "fluid drive effect", the "gravity effect", and the "capillary effect'' — is discussed, as well as implications of the analysis in connection with the study of certain types of petroleum reservoirs. INTRODUCTION The purpose of this paper is to clarify and summarize the mathematical basis of the theory of two-phase incompressible fluid flow through porous media, particularly as it pertains to vertical flow, and to present a qualitative* exposition of the controlling factors involved in circumstances where this type of flow may exist. Although the generally accepted theory of heterogeneous fluid flow through porous media was developed a number of years ago by Muskat,1 and Buckley and Leverett2, 3 using the basic premise of Darcy, (and since then expounded upon by many others) there is a need for an over-all summary and clarification of this theory, especially regarding certain types of applications in connection with so-called "gravity-drainage-type reservoirs". The source and derivation is outlined for what is referred to here as the "General Fluid Displacement Equation for Incompressible Vertical Two-Phase Flow through Porous Media''. This equation would apply under the condition where the pressure drop along the path of flow is negligible in comparison with the pressure level on the system, or where compressibility and solubility effects are negligible. These conditions exist ordinarily in gravity-drainage-type reservoirs. Specifically, it will be shown that this general equation may be developed directly from the basic equations, which, according to present theory, govern the general case of viscous heterogeneous flow through porous media. This general equation has appeared in the literature previously, but in most cases its development from basic theory is not indicated clearly, or the equation is presented in terms of groups of constants and variables involving reduced or dimensionless quantities. This presentation is expedient in cases of experimental or computer applications; but it may make it difficult for the practicing petroleum engineer to identify all the factors involved or to understand the relationships between them. Therefore, in the following development, only ordinary mathematical parlance will be used, and no terms involving groups of other equations or reduced or dimensionless quantities will be used. DERIVATION The following equations for two-phase oil and gas flow result from analogy with Muskat's general equations,** if solubility and compressibility effects are neglected, and if all volumes are considered in terms of reservoir conditions, and the water phase, if present, is considered to be immobile (or effectively a part of the porous medium.) In this case, the sum of the oil and gas saturations may be taken as unity, and the saturation of each phase is in terms of the total hydrocarbon saturation. Note that in Eqs. 1 and 2, and in the derivation following, z is taken as positive in the vertically downward direction,

Jan 1, 1969

By J. Lyden

In the Picher field, structure made openings for the circulation of the mineralizing solutions by flexing, shearing, and fracturing the sedimentary beds. This structure is used with the spatial and genetic relationship of the ore minerals, sphalerite and galena, and the gangue minerals, dolomite and jasperoid, in prospecting for ore bodies. THE Picher Mining Field, fig. 1, which lies between Baxter Springs, Kansas, and Commerce, Okla., is the most intensely mineralized and the largest zinc-lead ore producing area in the Tri-State District of Missouri, Kansas, and Oklahoma. It has a vast lateral extent of underground workings that is unequaled for the observation of the geology of zinc-lead ore bodies in sedimentary horizons; and thousands of churn drill holes in the unmined areas supplement the underground observations with useful data for the interpretation of the geology. This paper is confined to the ore deposits of the Picher mining field. The reader is referred to the bibliography for the general geology of the Tri-State district which has been ably covered by many geologists. The writer was co-author of several publications on the Tri-State district.'-" This paper is necessarily a repetition of parts of those publications but contains a few changes and additions on the deposition of the minerals. The parts of this paper concerning mineralization maps and pipe slump-structures are not covered in the above publications. Geology The geology of the Picher mining field is similar to that of the entire Tri-State district because the sedimentary horizons that are found here are found throughout the district, and the ore bodies in the respective horizons have similar characteristics. The beds that contain the ore bodies in the Picher field are illustrated and described in fig. 2. The five unconformities found in the mines of the Picher field are indicated on the geologic section, fig. 2. The unconformity shown at the base of Meramec (B bed) is relatively unimportant since B bed was mostly eroded from the area of the Picher field before the Chester beds were deposited. B bed has been observed in the cuttings from only a few churn drill holes. The Pennsylvanian (Cherokee shale) formation is the top horizon found in the Picher mining field. It has been eroded from the southeastern part of the field, but because of the regional dip of the sedimentary beds to the west, it attains thicknesses of 100 ft to 200 ft along the west edge of the field. It is 200 ft to 300 ft thick in the Miami trough. It was deposited on the Boone limestone surface, which contained relatively few shallow erosion channels and very few depressions. Subsequent to the deposition of the shale, solution of limestone from underlying limestone horizons by circulating solutions caused the overlying beds, including the Cherokee shale, to slump into the larger openings formed by the solution and removal of the limestone. Chert The origin of the chert in the Tri-State district has been a controversial subject among geologists. Tarr7 advocated a syngenetic origin for the chert, postulating that it formed from colloidal silica deposited in the Mississippian seas. Leith, Dake and Leighton' argued in favor of silicification of erosion

Jan 1, 1951

By J. Lyden

In the Picher field, structure made openings for the circulation of the mineralizing solutions by flexing, shearing, and fracturing the sedimentary beds. This structure is used with the spatial and genetic relationship of the ore minerals, sphalerite and galena, and the gangue minerals, dolomite and jasperoid, in prospecting for ore bodies. THE Picher Mining Field, fig. 1, which lies between Baxter Springs, Kansas, and Commerce, Okla., is the most intensely mineralized and the largest zinc-lead ore producing area in the Tri-State District of Missouri, Kansas, and Oklahoma. It has a vast lateral extent of underground workings that is unequaled for the observation of the geology of zinc-lead ore bodies in sedimentary horizons; and thousands of churn drill holes in the unmined areas supplement the underground observations with useful data for the interpretation of the geology. This paper is confined to the ore deposits of the Picher mining field. The reader is referred to the bibliography for the general geology of the Tri-State district which has been ably covered by many geologists. The writer was co-author of several publications on the Tri-State district.'-" This paper is necessarily a repetition of parts of those publications but contains a few changes and additions on the deposition of the minerals. The parts of this paper concerning mineralization maps and pipe slump-structures are not covered in the above publications. Geology The geology of the Picher mining field is similar to that of the entire Tri-State district because the sedimentary horizons that are found here are found throughout the district, and the ore bodies in the respective horizons have similar characteristics. The beds that contain the ore bodies in the Picher field are illustrated and described in fig. 2. The five unconformities found in the mines of the Picher field are indicated on the geologic section, fig. 2. The unconformity shown at the base of Meramec (B bed) is relatively unimportant since B bed was mostly eroded from the area of the Picher field before the Chester beds were deposited. B bed has been observed in the cuttings from only a few churn drill holes. The Pennsylvanian (Cherokee shale) formation is the top horizon found in the Picher mining field. It has been eroded from the southeastern part of the field, but because of the regional dip of the sedimentary beds to the west, it attains thicknesses of 100 ft to 200 ft along the west edge of the field. It is 200 ft to 300 ft thick in the Miami trough. It was deposited on the Boone limestone surface, which contained relatively few shallow erosion channels and very few depressions. Subsequent to the deposition of the shale, solution of limestone from underlying limestone horizons by circulating solutions caused the overlying beds, including the Cherokee shale, to slump into the larger openings formed by the solution and removal of the limestone. Chert The origin of the chert in the Tri-State district has been a controversial subject among geologists. Tarr7 advocated a syngenetic origin for the chert, postulating that it formed from colloidal silica deposited in the Mississippian seas. Leith, Dake and Leighton' argued in favor of silicification of erosion

Jan 1, 1951

By H. K. van Poollen, H. C. Bixel

A treatment is given of the transient pressure behavior of a well located at the center of a circular region surrounded by a radial discontinuity. On either side of the discontinuity, the values of permeability, viscosity, compressibility and porosity are uniform but may be different from those on the other side of the discontinuity. The results are obtained by solving a pair of finite difference equations. The numerical solution to these equations is obtained using a digital computer. The results are compared with previously published, approximated analytical solutions to the same problem. Solutions, presented graphically, show pressure decline for constant rate fluid production. The range of variables studied include dimensionless time from '0.001 to 100 and storage capacity ratio from 0.001 to 1,000. The well behaves as if it were in an infinite reservoir for dimensionless times less than 0.25. Reservoir properties near the well can be estimated in the usual manner. An overlay technique is used to match an experimental curve with one of the theoretical curves. It is possible to estimate the distance to a discontinuity by substituting the actual time t and the corresponding dimensionless time tD at which a match occurs into the equation a = (0.000264 tk1/tD , µ1 cI)I/2 where kI/ I µI cI is the diffusivity near the well, and may be estimated from data taken at early time. Several buildup curves are computed. These curves show that for early shut-in times, correct values for transmissibility are obtained from conventional analysis. However, erroneous values of static reservoir Pressure are obtained unless data at large shut-in times are taken. INTRODUCTION A mathematical treatment of the transient pressure response of a well located at the center of a region bounded by a circular discontinuity is given. Within a region (Fig. 20) the properties of both the rock and the fluid are considered to be constant on either side of the discontinuity. While these properties are considered constant, they may be different on opposite sides of the discontinuity. A discontinuity of this type could be a fluid-fluid contact or a sudden change in rock characteristics such as thickness, porosity or permeability. Analytical solutions to this problem are available. 1-3 However, they are so involved that they are of little practical use. An approximate solutionl is available but the range of times over which it is valid has not been specified. A numerical solution to a pair of finite difference equations is used to obtain the solution given in this paper. PREVIOUS WORK One of the first solutions to the problem was published by William Hurst.1 Hurst considered unsteady-state flow of fluids through two sands in series with different mobilities in each sand. He used Laplace transforms to obtain a solution for a single well located at the center of the circle enclosing the first of the two sands. In this case, the solution for the pressure change in Region I (Fig. 20) is2

By R. L. Perrine

This paper shows how stability theory can be used to optimize solvent recovery of oil. Application of the theory leads to definition of the limiting conditions required for stable displacement to occur. One of these conditions is that the size of a solvent "slug" must at least equal a prescribed minimum. The criteria to be satisfied are miscibil-ity and stability. Stability implies that no viscous fingering will occur and that mixing will be caused only by a dispersion process. Miscibility implies that complete recovery will be obtained from the swept regions. Thus, for any specified set of reservoir conditions, an optimum use of solvent is defined. INTRODUCTION The early outlook for solvent flooding as a means to increase oil recovery was very favorable. Some laboratory results indicated that a "slug" containing perhaps 2 to 3 per cent of a hydrocarbon pore volume could be successful. However, other data suggested as much as 30 per cent would be required. The difference is of considerable economic importance. A theoretical explanation for these divergent results has been advanced by the author.1,2 Stability theory defines conditions for two distinct flow regimes. In stable displacement, solvent and oil become mixed by a dispersion process, and the solvent requirement is small. On the other hand, unstable displacement can degenerate into viscous fingering. The practical result is a considerable increase in the extent of mixing and, thus, in the solvent required. The present paper shows how to use stability theory to optimize solvent recovery of oil. Oil is usually considered to be displaced by a small amount, or a slug, of solvent. Gas in turn follows solvent. Any fingering will permit contact of nearly solvent-free gas and oil, leading to immiscibility and reduced recovery. Thus, our optimum is defined by two restrictions — stable flow and miscibility. Although an immiscible solvent process could prove more profitable than any miscible process, such processes lie outside the selected definition of an optimum. The usefulness of computations based on the present work will depend on the validity of the general theory. Because the important idealizations required tend to minimize the predicted solvent requirement, the results should state correctly the limiting conditions required. Therefore, theoretical calculations should have practical value. This paper first reviews several principles that result from stability theory. The following section describes use of these ideas in relatively simple systems which symmetry makes appear one-dimensional. Of particular importance is the step-by-step design of 3 stable minimum-solvent slug. The use of stability theory in cases of multi-dimensional displacement is discussed and, finally, suggestions are given for simplified practical application of the theoretical results. PRINCIPLES OF STABILITY THEORY The use of perturbation methods to derive stability conditions has been shown by the author.l The discussion is presented in terms of the fractional concentration of solvent in the single hydrocarbon phase. Quite generally, any disturbance can be represented as a Fourier series, of which only the least stable term need be considered. Denoting this term at time t = 0 by cn,

ASSETS CAPITAL ASSETS Equity in United Engineering Society's Land and Buildings $486,792 79 Library 40,000 00 $526,792 79 INVESTMENTS Jas Douglas Fund-Schedule #2 $ 99,966 40 Life Membership Fund-Schedule #3 9,415 63 R W Hunt Medal Fund-Schedule #4 7,489 09 116,871 12 INVENTORIES Paper Account .305 10

Jan 1, 1923

[ASSETS CAPITAL ASSETS: Equity in United Engineering Society's Land and Buildings $486,792.79 Library 40,000.00 $526,792.79 INVESTMENTS: Jas. Douglas Fund-Schedule #2 $ 99,966.40 Life Membership Fund-Schedule #3 9,415.63 R. W. Hunt Medal Fund-Schedule #4 7,489.09 116,871.12 INVENTORIES: Paper Account 305.10] [ ]

Jan 1, 1925

By M. J. Pool, P. J. Spencer

Using liquid tin as the solvent metal, the heats of solution of silver and gold in dilute Ag-Au-Sn alloys have been determined at 723°K by solution calorimetry. From the values obtained, the various enthalpy interaction coefficients in the liquid solutions have been calculated. The self-interaction coefficients Au and Ag values of 2413 and -6322 cal per g-atom in binary Au-Sn and Ag-Sn alloys, respectively. For an alloy containing 0.04 mole fraction Ag, Au is equal to 2443 cal per g-atom, and in an alloy containing 0.04 mole fraction Au, Ag has a value of —8883 cal per g-atom. Ag Au has been determined as —2650 cal per g-atom. ADDITION of a second solute to a dilute binary alloy may cause striking changes in the thermodynamic characteristics of the alloy. As yet, such influences cannot be reliably predicted and it is only by accumulation and critical assessment of data that definite patterns can be established. Solute interactions in dilute solutions were first treated mathematically by Wagner,1 who derived expressions for the Gibbs energy interaction coefficients. For an alloy consisting of. two dilute solutes, i and j, in a solvent s, these coefficients are given by: where yi is the activity coefficient of component i and x represents the mole fraction of solute or solvent. Other interaction coefficients have since been established in terms of the various partial molar thermodynamic properties of an alloy; the definitions of these are summarized in a recent paper by Lupis and Elliott.2 Mathematical and experimental studies of such coefficients have received much attention recently, providing a very useful theoretical background to an understanding of the nature of solute interactions taking place in dilute solutions. One of the definitions to arise from such work has been the extension of Wagner's treatment by Lupis and Elliott4 to include an enthalpy interaction coefficient, defined as. where ?Hi is the relative partial molar enthalpy of component i. ?Hi is related to the relative partial molar enthalpy at infinite dilution, ?Hio, and to the enthalpy interaction coefficients by the expression: Values of ?Hi can often be obtained with a high degree of accuracy by calorimetry, and, if the composition of the alloy is carefully controlled by making calculated solute additions throughout a series of measurements, application of Eq. [2] will enable reliable enthalpy interaction coefficients to be determined. Partial heats of solution must be investigated as a function of solute concentrations down to xi = 0, and, since ? values are obtained from the slope of mi plotted against x, great care must be taken to obtain precise data. The data for binary systems which are presently available often require extrapolation of ?Hi values from compositions as great as xi = 0.05 or even 0.1 to obtain limiting heats of solution. Reliable enthalpy interaction coefficients are thus impossible to obtain from published data for most of the alloy systems already investigated. The aim of the present work was to determine values of Au, Ag, Ag, and Au in the limit xsn -1 for the relatively simple Ag-Au-Sn system and from these results to gain some insight into the possible influence

Jan 1, 1969

By S. I. Liu

THE effects of strain histories, consisting of several prestrains in opposite directions, on the flow and fracturing characteristics of metals determined in a final test have been investigated previously.'" Such strain histories vary from a single prestrain in tension or compression to the number of strain cycles leading to fatigue failure.' Between these two limits, various strain histories could be visualized and some can be attained readily. One such example is a strain history consisting of a first prestrain in tension of various magnitudes and a second prestrain in compression also of various mag-nitude. In this investigation the strain history was extended to the combination of these two limits, i.e., a single prestrain in tension or compression followed by balanced strain cycles of a selected magnitude e, = k0.12. It was found in this case that only compressive initial prestrains could be investigated with sufficient accuracy.* Such strain histories can be considered also as (low cycle) fatigue tests of a metal subjected to various amounts of cold working. It appears from previous publications that cold working within a wide range of reductions usually raises the un-notched fatigue strength of many metals.'-' This effect, however, has been found to be inconsistent and sometimes reversed for other metals?.7 Furthermore, Ludwik reports that the yield strength of cold-worked specimens may be reduced by cyclic strains, while that of materials without cold work is generally increased in the initial cycles." " In addition to the above tests, a study was made of the effect of intermediate re-solution heat treatment on low cycle fatigue behavior. Such anneals should eliminate the strain hardening induced by the cyclic strains. As far as their effect on the fracture characteristics is concerned, a few previous tests seemed to indicate that the damage resulting from cyclic strains is retained only partially after heat treatment." A further investigation was made in which one specimen was subjected to repeated unbalanced tension cycles in which the strain interval was approximately $ 0.013. This repetition of plastic tension damages the material slightly. This result appears to confirm Ludwik's observations." " Commercial 3/4-in. rod of the aluminum alloy 24ST4 was selected for this investigation. The material was subjected to the following treatments before machining: 1—Re-solution treatment at 920" ± 10°F for 45 min, 2—water quench at room temperature, and 3—aging for four days at room tem-perature.? The treated material then was machined to desired specimen contour and tested. A coolant was used during machining to minimize any artificial aging effects of heating during machining. In some cases the 24ST4 specimens were reheat treated after having been strained. In these cases, the heat treatment was the same as the re-solution heat treatment described above. Procedure As shown in Fig. 1, threaded end specimens with a minimum diameter of 0.266 in. and a contour radius of 2 in. were used for prestraining to an axial compressive strain ranging from 6, = —0.10 to E, = —0.48. For large prestrains, two consecutive corn-

Jan 1, 1952

By Larry D. Patts

Section 317(e) of the Federal Coal Mine Health & Safety Act of 1969 directed the Secretary of the Interior to prepare standards under which all working places in a mine shall be illuminated by permissible lighting while persons are working in such places. Section 317(e) further provides that such working places shall be illuminated within 18 months after such standards are promulgated. In accordance with this section of the Act, there was published in the Federal Register for December 91, 1970, a notice of proposed rulemaking which prescribed the illumination to be provided in the working places of underground coal mines. In light of written comments, suggestions, and objections to this proposed rulemaking, the proposedstandards were withdrawn and reproposed in the Federal Register for Wednesday, October 27,-19h. In light of further comments, suggestions, and objections, a public hearing was held on April 4, 1974, and standards were again reproposed and published in the Federal Register for April 1, 1976. Promulgation of the final lighting standards took place on October 1, 1976, which means that the underground coal mining industry must comply with face illumination requirements by April 1, 1978. As mentioned previously, the first proposed rulemaking for illumination of underground coal mines was published in the Federal Register on October 27. 1971. In early 1972, Consolidation Coal Company (Consol) and the United States Bureau of Mines agreed to a cooperative study of underground face illumination: Consol felt that expertise is this field would become increasingly important. Consol's initial efforts in illumination were aimed at investigating practical lighting systems for underground face equipment. We were concerned with installing unobtrusive lights which provided sufficient face illumination for safety, but at the same time were readily maintainable, electrically reliable, and physically sheltered from damage. We believe that our initial lighting systems did provide sufficient face lighting for safety, but because only prototype components were available for field testing, the resultant poor system reliability and maintainability necessitated drastic improvement before face lighting could become practical. Final Lighting Standards Deem Early Lighting Installations Out Of Compliance On April 1, 1976, the Federal Register contained the final version of the illumination standards (as they were later promulgated in October). When these illumination regulations and measurement techniques were defined and measuring instruments were available, Consol checked their lighting systems underground and determined that the systems were not in compliance with these final illumination standards. More Lighting Hardware Added In An Attempt To Achieve Compliance. After determining that all of our face lighting systems were not in compliance, we began adding additional lighting hardware in order to meet compliance with published regulations. Unfortunately, to date, we have not been able to meet compliance with practical lighting systems. We have determined from our field installations that the required additional lighting hardware, (to meet compliance) with its increased vulnerability and decreased reliability, renders the lighting systems impractical, if not impossible, to reasonably maintain. Our attempts to provide 0.06 footlamberts have also produced adverse operator reaction to the glare and to illumination systems in general. BCOA Members Ask MESA To Demonstrate Practicability Of Compliance With Regulations Industry concern about meeting the impending lighting regulations was mounting, and in May of 1976 a meeting between MESA and BCOA members was held to discuss lighting compliance problems. At this meeting, BCOA offered to work cooperatively with MESA in testing the practicability of various lighting systems mounted on underground mining equipment. Field tests were to be conducted by United States Steel Corporation, American Electric Power Service Corporation, and Consolidation Coal Company. The purpose of this underground field testing was to develop capability to provide adequate face illumination in a safe, workable manner which would not detract from efficiency of operation. BCOA members involved in this cooperative study were to submit necessary machine drawings, sketches, etc. to MESA in order that MESA could perform a "black-box" study and specify the type and location of luminaires to be installed on the test machines. MESA was confident that they could specify lighting systems that would be in compliance and would be practical so as not to detract from efficiency of operation. Consol was first to install lighting hardware under the BCOA/MESA cooperative agreement. As per MESA specifications, Control Products HgV luminaires were installed on a Joy 2BT-2H boring machine at the Williams Mine of Northern West Virginia Region. As of mid-October, 1976, Consol had approximately eight weeks operating experience with the lighting system on this boring machine underground and had drawn the following conclusions: The lighting system installed at Williams Mine (1) does not meet compliance with lighting standards as originally proposed by MESA, (2) does not provide illumination in a safe workable manner, and (3) will detract from efficiency of the mining operation due to operational delays. Although Consol has rearranged lights on this boring machine in an attempt to reduce operator objections, a practical lighting system which is "in compliance" has not been arrived at as of this writing.

Jan 1, 1979

By T. A. Rickard

A knowledge of the principles of punctuation is essential to effective and intelligible writing, for the ease and pleasure of the reader, and even his understanding, may depend upon the choice and the placing of punctuation marks. To 'punctuate' is to mark with stops or points; the word comes from the medieval Latin punctuare (punctuatus), which in turn is derived from the Latin punctum, a point. The purpose of punctuation is to show the manner in which the writing is to be understood; to indicate the relations between parts of a sentence and between successive sentences. To some extent "it does for the eye what vocal stress does for the ear", but especially it marks logical relations. Some punctuation marks, such as those indicating admiration, exclamation, and interrogation, are rhetorical as well as grammatical, but most of the common ones are logical, or grammatical. My discussion will be confined to grammatical punctuation in ordinary writing. .'The problem of punctuation in text matter", as George Summey * says, "is to employ words, points, and paragraph breaks in such a way as to achieve at the same time clearness; proper distribution of emphasis, and the desired kind of movement." The criticism of the punctuation of a sentence or of a group of sentences is not final until the context, within the paragraph, is read. A paragraph is a sentence or a group of sentences forming an independent unit of the composition; it represents a unit of thought. A multiplicity of paragraphs produces a choppy effect; 'on the other hand, paragraphs of. excessive length are tiresome, because the belaboring of one unit of thought wearies the reader. The aim should be to

Jan 1, 1931

By B. B. Gottsberger

A NOTABLE feature of the practice of the American mining engineer is the fact that 'his field has been world wide, and the results of his work may be found in all countries. For this reason, the mining engineer is particularly interested in any legislation tending to restrict his freedom in this respect. In their zeal to improve the status of the professional engineer, those responsible for the enactment of the registration laws now in effect in various of the United States may have introduced a practice that will result very much to the detriment of the American mining engineer. He is preeminently interested in the maintenance of the professional "open door," and fame may be the reward of him who calls the first "International Conference for the Limitation of Restrictive Legislation." There is no reason why these United States should be the only country to regulate the practice of professional engineering and, in fact, the movement is spreading beyond its borders. Already, it is necessary for the mining engineer to be thoroughly conversant with the various state laws in order to insure his right to pursue his calling. It may soon be necessary for him to make sure of his status in foreign countries before undertaking work in them.

Jan 1, 1921

By J. W. Smith

Our continuous search for underground productivity improvements has been brought about by the diminishing ore grades in existing underground mines. The need for more efficient mining methods is a result of the economic problems facing our industry today, and this has caused us to evaluate underground haulage methods which have traditionally been the "bottleneck" in the flow of material from the ore in the natural state to the surface processing facility of any underground mining operation. Small improvements in the face haulage systems have yielded much greater benefits as they relate to overall mine productivity so it's only natural that we are all concerned with the best method of moving ore from the face to the main line haulage. In a recent paper titled "Underground Haulage Trucks - Gaining Momentum Worldwide", Richard A. Thomas concludes that the use of trucks to haul ores in underground mines is on the increase spurred by the convergence of a number of technology advances and economic realities. Perhaps the most important stimulus for the growth of trackless haulage is the high degree of haulage flexibility in underground operations. On the economic side, the demand for higher productivity from underground mines has resulted in larger physical dimensions of haulage roads, that is, higher backs and wider drifts to provide more room for high capacity haulage units. In the process of determining the most effective type of equipment for haulage, the power source must be a major consideration. For the purpose of this paper, we will limit the comparison to rubber-tired trackless haulage vehicles and not try to make a comparison between rubber-tired haulage, continuous haulage systems and rail-mounted haulage. Cost is perhaps the only really measurable factor when making a comparison between electric and diesel haulage. You will find that some costs will be very well defined in absolute terms. In other areas of comparison, cost can be fairly well estimated, and yet in still others, the costs are totally arbitrary. Let's take a look at some of the cost considerations. (Figure 1) first of all, is the initial cost of the equipment. This capital cost quite often is a determining factor in the type of haulage vehicle to be selected, yet this initial cost is perhaps the most insignificant of all costs when evaluating an operation over the long term. Of much greater concern, is the cost of maintenance. This cost will often run three times the original capital investment during the life of a single piece of haulage equipment. This factor can include rebuild to extend the life of the original capital investment, but certainly includes the labor and materials necessary, plus the inventory to keep the equipment in good repair. Perhaps one cost which is now playing an even greater role in the rubber-tired haulage operation, is the cost of fuel. Conoco has recently come up with some rough estimates which indicate that diesel fuel will cost an average of three times the equivalent kilowatt output in direct electric power. Diesel fuel is almost twice the cost of stored electric power. (This of course relates to the efficiencies of charging and recovery of power from lead acid storage cells.) These particular figures of course will vary from one area to another but I think that there is enough significance here to certainly warrant the further study of fuel costs for each particular area or mine. Another cost is breakdown expense. This must be treated differently from maintenance costs because a potentially larger expense is involved, more than just parts and labor. Now we have to deal with the cost of lost production time, which can have a much greater overall effect. Mine plan economics are another cost consideration where we can't make a comparison without looking at specifics. Here you must look at the movement of power centers vs. the flexibility and freedom of movement of vehicles. The determination must be made as to what types of equipment will fit into any predetermined mine plan and if a change in the planned roadway dimensions for the mine plan itself would be more economical so that more efficient type of equipment could be utilized. Finally, two of the most important aspects to be considered with potential ramifications far beyond what we have mentioned previously, is the cost of health and safety, which is really the cost of meeting current and future government regulations, reasonable or otherwise. And of course, when making any consideration here it is impossible to come up with anything more than an educated guess on the cost of meeting the new regulations. Now let's take a look at some of the advantages of diesel vehicles as well as advantages offered by electric vehicles, both battery and cable powered versions (Figure 2). Much of the data used in this comparison is based on experience with three vehicles manufactured by Jeffrey Mining Machinery Division, Dresser Industries. Jeffrey manufactures all three types, each with approximately a 15-ton capacity, even though few of these Jeffrey vehicles are used in uranium mining operations. Much of our experience comes from the 4114 diesel powered RAMCAR which is a 4-wheel drive, articulated steering,vehicle powered by a Caterpillar 3306NA engine and using a powershift transmission. This will be compared with the performance of the Jeffrey 404H battery powered RAMCAR with articulated steering which utilizes a separate 35 HP DC drive motor on each of two wheels with solid-state speed controls, and the final comparison will be made on the Jeffrey 4015 cable-reel shuttle car which is powered by two 60 HP constant

Jan 1, 1982

By Elmer A. Jones

Development work in mines of St. Joseph Lead Co., Southeast Missouri, using trackless loading equipment shows definite advantages: Speed of cleaning, ability to work on steep grades and sharp crosscuts, good later tracking conditions, and possibility of wasting rock in old abandoned stopes. THE Desloge mine is one of a group of mines owned by the St. Joseph Lead Co., in the so-called Lead Belt of Southeast Missouri. It has been operating approximately 40 years producing a daily tonnage ranging from 1600 to 3800, depending on various factors. On an average, the present mine is 300 ft deep with an extreme extent of 2.7 miles by 1.7 miles. Most of the present mining is in the lower horizons of the Bonne Terre dolomite, a fairly soft rock requiring no support except occasional channel iron and roof pins. Due to the contour of the underlying sandstone and porphyry, some development work has been through short stretches of these different formations. In some areas the lower part of the dolomite is quite sandy and generally is considered abrasive. Sizes and Methods of Drifting Have Changed: Development work has, like other phases of mining, changed considerably in the last 20 years, from cleaning by hand to the use of a mechanical method. The conception of a standard drift has also changed. Before the advent of mechanical loading in stopes there were many pieces of main line drift averaging 7 ft high x 9 ft wide. With the coming of the St. Joe shovel the drift was increased to 8 ft high x 10 ft ELMER A. JONES, Member AIME, is Assistant General Mine Superintendent, St. Joseph Lead Co., Bonne Terre, Mo. AIME Columbus Meeting, September 1949. TP 2859 A. Discussion (2 copies) may be sent to Transactions AIME before July 31, 1950. Manuscript received Sept. 16, 1949. wide. Now with the Joy loader and shuttle car, a 9x11 ft drift is coming to be standard size. Methods of cutting drifts have changed considerably over the last few years. Some changes in drilling equipment have been made such as reducing the weight of column, clamp, air feed, and fittings to go with the HC10 Cleveland jackhamer. Other changes have been made in drill steel such as the use of detachable bits; throw-away variety, screw type, and the tungsten-carbide insert bits. Later developments have introduced spiral-welded pipe with victaulic couplings, millisecond exploders, bulky powder, and the use of electric cap lamps. Experimental work is going on continually in various phases of development work, some to be tried and discarded, others gradually to become standard practice. To sum up, the standard method of development now in use at Desloge is as follows: The work is done on a two-shift cycle 7:00 p.m. to 3:00 a.m. and 7:00 a.m. to 3:00 p.m. Two men known as development drillers comprise a crew on each shift. These two men arrive at their work about 7:30 to find a round blasted by the previous shift. After scaling down back and walls they proceed to the cleaning operation, using either a Joy loader and shuttle car, a drag hoist mounted on a slide ramp, or an Eimco Finlay to load into a 21/2 ton mine car. Cleaning may take from 2 to 4 hr depending on conditions such as length of round broken, length of haul, and other variables. After fitting up pipe and setting up columns and drills they are ready to drill a round which should measure 9 ft high x 11 ft wide and break from 5 to 7 ft advance. This may also take from 2 to 3 hr. Then they are ready to charge and

Jan 1, 1951

By Elmer A. Jones

Development work in mines of St. Joseph Lead Co., Southeast Missouri, using trackless loading equipment shows definite advantages: Speed of cleaning, ability to work on steep grades and sharp crosscuts, good later tracking conditions, and possibility of wasting rock in old abandoned stopes. THE Desloge mine is one of a group of mines owned by the St. Joseph Lead Co., in the so-called Lead Belt of Southeast Missouri. It has been operating approximately 40 years producing a daily tonnage ranging from 1600 to 3800, depending on various factors. On an average, the present mine is 300 ft deep with an extreme extent of 2.7 miles by 1.7 miles. Most of the present mining is in the lower horizons of the Bonne Terre dolomite, a fairly soft rock requiring no support except occasional channel iron and roof pins. Due to the contour of the underlying sandstone and porphyry, some development work has been through short stretches of these different formations. In some areas the lower part of the dolomite is quite sandy and generally is considered abrasive. Sizes and Methods of Drifting Have Changed: Development work has, like other phases of mining, changed considerably in the last 20 years, from cleaning by hand to the use of a mechanical method. The conception of a standard drift has also changed. Before the advent of mechanical loading in stopes there were many pieces of main line drift averaging 7 ft high x 9 ft wide. With the coming of the St. Joe shovel the drift was increased to 8 ft high x 10 ft ELMER A. JONES, Member AIME, is Assistant General Mine Superintendent, St. Joseph Lead Co., Bonne Terre, Mo. AIME Columbus Meeting, September 1949. TP 2859 A. Discussion (2 copies) may be sent to Transactions AIME before July 31, 1950. Manuscript received Sept. 16, 1949. wide. Now with the Joy loader and shuttle car, a 9x11 ft drift is coming to be standard size. Methods of cutting drifts have changed considerably over the last few years. Some changes in drilling equipment have been made such as reducing the weight of column, clamp, air feed, and fittings to go with the HC10 Cleveland jackhamer. Other changes have been made in drill steel such as the use of detachable bits; throw-away variety, screw type, and the tungsten-carbide insert bits. Later developments have introduced spiral-welded pipe with victaulic couplings, millisecond exploders, bulky powder, and the use of electric cap lamps. Experimental work is going on continually in various phases of development work, some to be tried and discarded, others gradually to become standard practice. To sum up, the standard method of development now in use at Desloge is as follows: The work is done on a two-shift cycle 7:00 p.m. to 3:00 a.m. and 7:00 a.m. to 3:00 p.m. Two men known as development drillers comprise a crew on each shift. These two men arrive at their work about 7:30 to find a round blasted by the previous shift. After scaling down back and walls they proceed to the cleaning operation, using either a Joy loader and shuttle car, a drag hoist mounted on a slide ramp, or an Eimco Finlay to load into a 21/2 ton mine car. Cleaning may take from 2 to 4 hr depending on conditions such as length of round broken, length of haul, and other variables. After fitting up pipe and setting up columns and drills they are ready to drill a round which should measure 9 ft high x 11 ft wide and break from 5 to 7 ft advance. This may also take from 2 to 3 hr. Then they are ready to charge and

Jan 1, 1951

By P. H. Royster, T. L. Joseph

In a study of the blast-furnace process, the Bureau of Mines has made many experiments for the purpose of determining the exact nature of the combustion of coke in the neighborhood of the tuyeres. Two papers1 presented at a meeting of this Institute discussed somewhat the practical aspects of coke combustibility in its relation to the operation of the blast furnace. In a later paper,2 Sherman and Kinney discussed the possible effect of variations in the combustibility of cokes on the furnace operation, and find that the "reoxidation theory" of Koppers and the "heat concentration theory" of Brassert³ are insuffcient to explain the variation in the conduct of different cokes that has been observed by furnace operators. In their report to the D-5 Committee of the American Society for Testing Materials, with which the Bureau of Mines has been cooperating, Perrott and Fieldner4 seem to agree with Sherman and Kinney that, for practical purposes, the nature of the combustion of coke at the tuyeres of any furnace is constant and is affected neither by the physical properties of the coke nor by the nature of the furnace operation. They omit as unimportant any tests on the combustibility of coke from their proposed methods for standard tests on coke. In the last two papers, it is pointed out that performance tests, in which all other factors except coke quality are kept constant, are to be desired and

Jan 1, 1924

By J. B. NEALEY

MANY nonferrous smelting plants have recently adopted natural gas as fuel with resultant economies, both in cost and efficiency of utilization. Not only has this fuel been used for roasting, reduction, sintering, drossing, and smelting, but also for power. All of the three big smelters near Salt Lake City, Utah, have been changed over from coal and oil firing to gas. Among these is the plant of the International Smelting Co., Tooele, an Anaconda subsidiary, smelters of both copper and lead ores. In the roasting division at Tooele are 32 MacDougall six-hearth roasters, each 16 ft. in diameter and 19 ft. high. Two gas burners are installed on each furnace. These burners are of the single-valve, automatic gas-air proportioning type using high-pressure gas at 10 lb.

Jan 1, 1933