Search Documents

By William S. McAleer

Two major trends in the coal industry today focus attention on the need for heat-drying equipment of a simpler, more flexible and less expensive type than has been considered standard equipment for drying coal. These trends are: I. The tremendous growth in the use of mechanical equipment to load coal both in underground mining and strip mining, which necessitates efficient mechanical cleaning of the fine as well as the coarse coal and thus means a growing tonnage of washed fine coal? with its attendant moisture problems. 2. The growing consumer demand for the smaller sizes for use as domestic stoker coal, with increasingly rigid specifications covering size, ash, and moisture analyses. ACCEPTED PRACTICE In the past, when, for example, 4 in. too coal has been washed, there was little trouble in producing a washed product 4 to o with a satisfactory resultant moisture. The 4 to 3/8-in. could be taken from dewatering screens at a surface moisture ranging from 2.5 to 3.5 per cent, depending upon the size consist. The 3/8-in. to o coal was generally dewatered satisfactorily with centrifugal driers, to final surface moistures from 5.5 to 8 per cent, again depending upon size consist. The centrifugal type of drier has definitely proved itself to be the most economical type of machine to handle coal approximately 3/8 in. to o as recovered by dewatering screens or drainage elevators with 15 to 25 per cent surface moisture and turn out a product with moistures as stated above. Sometimes such moistures (5.5 to 8.0 per cent) in the product are satisfactory. If not, an ultimate moisture, lower than 3 per cent, is seldom required and the centrifugal drier removes 70 to 85 per cent of the total moisture to be removed. In certain districts there has been a growing tendency to circumvent the use of centrifugals or other types of driers, by dewatering over screens of the wedge wire type and wasting all the finer sizes. Sometimes all the minus 28-mesh has been wasted and often the size wasted has been as large as 1/8-in. By wasting these finer sizes, a lower moisture can be obtained in the finished product, but taking into account the cost of the tonnage so lost, plus the added cost of ultimately disposing of this wasted tonnage, often the cost will be greater than the cost of heat-drying in a modern plant, which makes possible the recovery of all the tonnage. Moreover, with the moisture standards for domestic stoker equipment even these wasteful approaches to its solution do not solve the problem and there remains only the alternative of heat-drying. HEAT-DRYING Until about four years ago, heat-drying of coal at the preparation plants was confined chiefly to drying the fine sizes (approximately 3/8 in. to 0). Occasional

Jan 1, 1941

By Avnulf Muan, Egil Aukrust

Activity-composition curves jor cobalt oxide and manganese oxide in solid solutions with spinel-type structure have been determined by studying the equilibrium between the spinel phase and a coexisting solid-solution phase in the tewzperature range 1100" to 1400"C. Within limits of experimental error, the system displays the behavior of a regular solution. The excess integral free energy of mixing is represented by the equation . The standard free energy of formation of cobalt manganite, CoMn,O,, from the oxide components COO mzd Mn2OS at 1200°C is calculated to be -8.6 kcal. AMONG the technologically and theoretically most important oxide phases are those which crystallize with the same structure type as the mineral MgO . A120,. Although the name spinel originally was used only for this mineral, the term is generally used today to designate the whole group of oxide phases with this same structure type. It is in this wider meaning that the term is being used in the present paper. The previous literature on spinels is very extensive. There are two aspects of spinels which have attracted particular attention: the structure, including the nature and distribution of the cations present, and the physical properties (electric, magnetic). The status of knowledge in these fields has been well-summarized in recent review articles.1'2 By contrast, thermodynamic properties of spinels are virtually unknown. Delineation of the activity-composition curve over the whole composition range of a solid-solution series with spinel-type structure is the objective of the present work. The system at elevated temperatures (>1000"C) constitutes such a series. The activity-composition curves for this system can be calculated from a study of the equilibrium between the above spinel solid solution and a solid solution (Co,Mn)O with sodium chloride-type structure. Data for the latter solid solution have become available recently.3 The system, in contact with metallic CO at 1200°C, obeys Raoult's law. The determination of the activity-composition curve for the spinel phase is based on the following relations. Consider the reduction-oxidation equilibrium for cobalt ions according to the equation: Because it is impossible in practice to measure single activities of electrically charged constituents, we will treat the equilibria in terms of electrically neutral components. Eq. [I] can then formally be written as follows: where and the activities of cobalt oxide in the (Co,Mn)O and the spinel solid-solution phases, respectively, K is a constant at constant temperature, and Pa is the oxygen pressure of the gas phase. The numerical value of K can be determined from a determination of the oxygen pressure P& for the equilibrium coexistence of Cos04 and COO in the binary system Co-0. Under these circumstances be set equal to 1, and hence K = [Po Eq. [3] can therefore be written

Jan 1, 1964

By Roy J. Helfinstine, Gilbert H. Cady

One of the most urgent needs in the field of coal combustion is the ability to predict the performance of a coal from knowledge gained from small-scale tests. Numerous types of analyses and tests are conducted on coal, including the proximate and ultimate analyses, heating value, varieties of sulphur, ash analysis, ash fusion temperatures, free swelling index, petrographic analysis, and Gieseler. plasticity. The Illinois Geological Survey has made an intensive study of the value of these tests for judging the performance characteristics of the coal as actually utilized. To date, three reports1,2,3 have been issued, and another is being prepared. The present paper briefly summarizes some of the results found in the studies. Equipment The equipment used for the tests is described in some detail in the above mentioned publications. Briefly, it consisted of a domestic stoker, cast-iron boiler, and water-cooled heat exchanger, which were operated as a forced circulation hot-water system. The entire unit was mounted on scales. Instruments for recording the per- formance of the coal included a hot-water meter to indicate the quantity of water flowing through the boiler; a two-pen, mercury-actuated thermometer to record the temperatures of the water entering and leaving the boiler; a chemical-type meter to record the percentage of CO2 in the stack gases; a pressure gauge to record the static pressure in the stoker-air duct; and a multipoint potentiometer to record the temperatures in the stack and room, and the opacity of the stack gases. A 16 mm motion picture camera was available for taking pictures of either the fuel bed or the scale dial. Procedure The tests described in this report can be conveniently divided into three phases. For the first phase, a load of 5 or 6 tons of unwashed coal (usually screenings) was obtained from each of fourteen Illinois mines. These coals were all crushed and screened to a size of 35 in. (square hole) by 8 mesh. Combustion tests were made on a part of this raw, screened coal. Another portion was passed over a concentrating table to reduce the ash to what was considered to be commercially reasonable, and combustion tests were made on this upgraded coal. The ash content of the remaining coal was reduced to a still lower figure by passing it over the washing table with greater reject, or by standard float-sink procedure. This cleaned fraction was then tested in the stoker-boiler unit. Thus three coals with varying ash content were tested from each mine. For the second phase reported here, coals were obtained from four Arkansas mines and tested as received and after passing over the concentrating table with a normal reject. One Illinois coal was tested in the "washed" condition only. The third phase included tests on commercially prepared stoker coals

Jan 1, 1950

By C. G. Dunn, F. W. Daniels, M. J. Bolton

J. P. Nielsen—The data that Dr. Dunn and his associates have been obtaining are welcome checks on the theoretical aspects of grain boundary energies. With reference to the comments on the validity of the inter-facial tension concept, I should like to say that I have been having considerable difficulty myself in untangling the confusion between "interfacial tension" and "interfacial energy." The confusion however resolved itself for me when I learned that "interfacial tension" for solids, or at least crystals, is used with two distinct meanings. One meaning12. ' "hat is implied for "interfacial tension" is the work necessary to produce or increase the surface of the solid in question by a unit area, temperature and pressure held constant. This comes from the somewhat surprising but simple fact that surface tension and surface energy in the case of liquids are identical quantities. This synonymity has carried over to crystals, where it should be kept in mind that the tension connotation has meaning only by analogy with liquids and that no real stresses are being referred to. The only reason that there is apparently a set of stresses acting at a grain boundary junction is the optical illusion that liquid interfaces are being observed for the grain boundaries. The other meaning3,14,15 for the term has to do with actual states of stress in the surface of a material as would be measured by a system of forces applied to the surface to equate the surface stress state with that in the body of the crystal. J. B. Hess—Since the authors have proposed that the surface tension concept should be discarded in order to deal with the general case of interface energies in solids, their attention should be called to a recent paper by Gurney." The latter has shown, from a thermodynamic argument, that surface tension is a valid concept in solids. In fact, Gurney has rejected the idea that surface tensions are merely mathematical fiction and, instead, has given an interpretation of their physical reality. Finally, he has concluded that, as long as appreciable atomic migration takes place, specific surface energies and surface tensions must be equivalent in solids as well as in liquids. Accordingly, the authors' eqs 2 and 3 can be written with equal accuracy in terms of interface tensions, simply by replacing each E,! with its numerically and dimension-ally equivalent Interfacial tension ?,,. If the interfacial tensions (or specific energies) are independent of interfacial orientation, as is true in liquids, then the general equations that define the geometry at equilibrium of the common junction of three interfaces reduce to eq 1. However, neglect of the effect of boundary orientation is never completely justified theoretically' in dealing with crystalline solids; hence, use of eq 1 in such cases must always be considered as an approximation, though clearly a reasonable one for many purposes.1,2 At the same time, one should not be surprised that the assumption that interface tensions in solids are free from orientation

Jan 1, 1951

By R. S. Busk

Niels Engel (University of Alabama, University, Ala.)— In this paper it was pointed out that the electron-gas and energy-band theory accounts for the fact that the lattice parameters exhibit a sudden change when the electron concentration (number of bonding electrons per atom) exceeds a certain number around two. This statement is said to support and prove the electron-gas theory. But this theory is not able to account for a series of experimental data. Also several expectations, deduced from this theory, are not found to exist. In Figs. 6 and 7 the energy bands of the second and third periods are given as they must be assumed in order to account for the electrical properties of the elements in these periods. In Figs. 6 and 7 the electron-gas and energy-band theory is compared with the electron-oscillator hypothesis in accounting for the properties of the elements in the second and third periods. Fig. 6 shows the second period, The energy-bands are overlapping and separated to be in agreement with the electrical conductivity of the elements. The oscillator hypothesis explains conductivity due to electron vacancies. In graphite there is a closed s-shell in every other atom and two vacancies in the others. Conductivity is therefore only maintained by migration of s-electrons in graphite. In boron there are no s-electrons. The diatomic molecules of nitrogen and oxygen and the paramagnetism of oxygen can be accounted for by a similar behavior as the s-electrons of the bonding electrons. But this explanation will deviate too much for the purpose of this discussion. Fig. 7 shows the third period. In the energy-band picture about two s-electrons are assumed in magnesium and aluminum, but only one s-electron is assumed in silicon. The diamond lattice is assumed to be controlled by a sp3 hybrid. However the electron distribution develops ideally according to the oscillator hypothesis. Only sodium, magnesium, and aluminum exhibit electron vacancies and conductivity. To account for the insulator properties in Si, P, and S in the third period it must be assumed that the four last added p-electrons must be taken up in bands containing only one electron per band.' (Compare the electron band picture in Hume-Rothery.' Hume-Rothery does not consider the insulator properties of the nonmetals.) In the second period already the first p-electron must have entered a single electron band. Based on the energy-band picture in Figs. 6 and 7, the following questions must be asked: 1—Is it consistent with the energy-band idea that electrons of the same kind (p-electrons) can be divided into separated bands? 2—Is it consistent with the energy band idea that single electron bands can exist? 3—Why are the first two p-electrons (in boron and diamond) separated into two single electron bands in the second period, but overlapping in the third period (aluminum)? 4—Why are s-electrons and d-electrons taken up in continuous overlapping bands, while p-electrons are divided into single electron bands? 5—Why do the peaks and valleys (y and w and further x and z) of the energy band below four electrons per atom not show up in the electrical conductivity of alloys? For example consider the Li-Mg system or the alloys between Mg and three electron metals where the mentioned discontinuity in the lattice parameter is found. 6—Why does the beginning of the p-electron band (x) not show up in the lattice constants similar to the filling up of the s-electron band (z) ? In magnesium alloys the electron-gas theory postulates the first Brillouin zone to be filled at about two electrons per atom. This is claimed to explain the sudden change in lattice spacing and c/a values of several magnesium alloys when the electron concentration exceeds a few percentage points over two electrans per atom. This was emphasized in the paper by Busk. If the electron-gas energy-band theory is correct a sudden change in electrical conductivity and possibly other properties .should be expected when the same electron-concentration or temperature is exceeded. A sudden change in lattice spacing or other properties should also be expected when the filling degree is such that p-electrons are introduced into the p-band, for example at x in Figs. 6 and 7. Such phenomena are at found by experiment. and If the number of electrons should vary with the energy level depending on the average number of bonding electrons per atom, the electrical conductivity should be expected to vary in accordance with the energy band layout (Figs. 6 and 7) caused by different numbers of conducting electrons at different filling up degrees. Nothing indicating such a behavior is observed. In addition to these discrepancies between the electron-gas and energy-band theory and measured data, the theory violates the principles developed along with the Bohr theory of atomic structure. According to these principles a filled shell is saturated and therefore unable to form bonds. Therefore two S-electrons per atom should form a closed or saturated shell, which has been pointed out as accounting for the inability of helium to form bonds. Beryllium, magnesium, or calcium atoms with two s-electrons should be expected to form inert atoms with properties almost like the helium atoms. Several other inconsistencies and disagreements with measured data of the energy-band theory can be mentioned. Some of these are discussed with reference to other papers. 8 Because the electron-gas and energy-band theory seems to fail on several points, I have developed another theory which can account for all the phenomena the electron-gas theory is able to account for. This new theory is further able to account for things which are impossible to explain by the electron-gas theory at the present state.

Jan 1, 1953

By F. F. Claussen

The method of making silver ingots in use at this Mint being radically different from that employed at any other Mint of the United States or, so far as known to me, any Mint in the world, there may be some interest in a description of the apparatus used and a brief history of its distinguishing feature, viz., the rotary ingotmould, which, though not a recent improvement, is comparatively unknown. The furnaces used for silver-ingot-melting are four in number and have a capacity of some seventy thousand standard ounces of silver per day of eight hours. This output is increased, when the exigencies of the service demand it, to one hundred thousand ounces. They are built of fire-brick and elevated 21/2 feet from the floor of the melting-room, in order to have space to place iron boxes and to work, in case a crucible breaks in the furnace and its contents run into the ash-pit. The furnaces are circular in horizontal section, 2 $ feet in diameter and 29 feet high inside in the clear, and rest on castiron plates, with top-plates of the same, and sides encased in boileriron. The furnace-covers are also of cast-iron, dome-shaped, and are handled by means of a small crane and lever. The furnaces stand in sets of two, and one crane and one ingot-machine serves two furnaces. The crucibles used are made specially for this purpose of a mixture of black-lead and fire-clay; the size known as No. 200 will contain and safely melt, without danger of slopping over, from 8600 to nearly 10,000 ounces of standard silver; and this is the usual weight of the ingot-melt at this Mint, as against 1800 ounces at the Carson City mint and 2600 to 3000 ounces at Philadelphia and San Francisco. Each crucible will endure, on the average, ten melts. The crucible stands in the center of the furnace, on the bottom of an old one, cut down to a height of about three inches. The fuel used is coke. Experience has shown that, notwithstanding the higher first cost, Connellsville coke is cheaper than Alabama coke and much more suitable to the work. A small triangular black-

Jan 1, 1888

By D. L. Martin, E. R. Parker

IN a previous paper, one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with, and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a strengthening, so that a longer life at a given stress and temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver .2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. EXPERIMENTAL PROCEDURE Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1943

By R. L. Huntington, Frank P. Vance, George F. Russell, Robert Thompson

With the advent of higher pressures in the operation of natural-gas transmission lines, the removal of water vapor from the gas has become increasingly important in order to prevent condensation or formation of gas hydrate from slowing down or stopping the flow of gas. Intelligent design of these dehydration or gas-drying plants has been hampered through the Iack of experimental data on the water vapor content of natural gas at elevated pressures. In view of this need, this present investigation was sponsored by the Southern Natural Gas Co. in the Chemical Engineering laboratories at the University of Oklahoma Research Institute. Experimental results were obtained on the water-vapor content of natural gas up to 2000 lb. per sq. in. at atmospheric temperatures. The water content at 2000 lb. is approximately two thirds as much as it is at 1000 Ib. Deviations from the ideal gas laws vary directly with pressure and indirectly with temperature. Introduction The removal of water vapor from natural gas is an important operation in connection with the production and transportation of this commodity because: I. Liquid water accelerates internal corrosion of a pipe line. 2. Accumulation of water at low points in a pipe line reduces markedly its capacity. 3. Gas hydrates, icy snowlike growths, form readily under high pressure in the presence of the lower hydrocarbons and water, often plugging up the pipe line. In order to design dehydration plants for stripping the gas of its water content, it is essential that the engineer. have a knowledge of the saturated or equilibrium water-vapor content of the gas to be processed. With the gradual increase of operating pressures around gas-producing wells and pipe lines, it was observed that the quantity of water recovered from dehydration plants or condensed in colder lines was considerably greater than had been expected from calculated contents, based on vapor-pressure data taken from steam tables. This observation prompted a number of investigators, for instance, Laulhere,3 Dea-ton,l and Hammerschmidt2 to carry out experimental work at pressures up to 600 lb. per sq. in. in order to determine quantitatively the water content of various gases. Sage, Lacey, et al.4,5 have recognized more recently the need for such data at higher pressures, but their work was done at temperatures of 100ºF, and higher. Since hydrate formation usually, if not entirely, occurs at temperatures below 100ºF., the present investigation was confined to the . lower temperature range at pressures from 600 to 2000 lb. per sq. in. gauge.

Jan 1, 1945

By P. W. Ramsey, E. J. Boyle, E. A. Anderson

ONLY a few zinc-rich alloys are in commercial use today, and these depend largely upon solid solution effects for their desirable properties. Typical examples are rolled alloys containing about I per cent of copper, with or without additions of elements such as magnesium,1 and die-casting alloys containing about 4 per cent of aluminum with small amounts of magnesium and sometimes copper.2 A number of elements are capable of forming alloys with zinc, which do not enter into solid solution except in limited degree. The present paper considers one such system, zinc-titanium, in which alloys having potentially useful properties in the rolled form were found. ZINC-TITANIUM SYSTEM The zinc-rich portion of the zinc-titanium diagram, as determined by standard methods in this laboratory,3 is shown in Fig. I. The portion of the diagram of significance in the present work extends from 0 to about 0.5 per cent titanium. Gebhardt4 places the eutectic at 0.45 per cent, but the evidence in favor of the composition given in Fig. I is considerable. The solid solubility of titanium in zinc is very low indeed and possibly places these alloys in a somewhat different category from the commercial alloys previously mentioned. ALLOY PREPARATION All of the alloys used in this work were prepared with titanium metal of 98.9 per cent purity. In most cases high-purity zinc (99.99 per cent) was used but sufficient work was done later to show that zinc of about high-grade composition would yield approximately equal results. Best practice in alloy manufacture seemed to be to prepare a zinc-titanium hardener by adding about 4 per cent of titanium metal to molten zinc and holding under a boric acid cover, with frequent stirrings, at 750°C. until the titanium had dissolved. The desired titanium content could readily be obtained in the final alloy by adding the calculated amount of this hardener. The alloys proved to be quite stable in composition, unless overheated, and, with reasonable temperature control, required no cover or flux to prevent loss of titanium content by oxidation. HOT-ROLLING TESTS Three alloys containing, by analysis, 0.05, 0.12, and 0.23 per cent titanium were selected for preliminary study. Slab cross sections revealed a marked grain refinement* (Fig. 2) in the two alloys of highest titanium content. Cast unalloyed zinc has a columnar grain structure similar to that shown for the alloy of lowest titanium content but without the scatter of small equiaxed grains at the center.

Jan 1, 1944

By N. J. Grant, D. S. Bloom

THE development of high temperature, high stress alloys had proceeded with such rapidity during the war, and for a short time afterward, that our knowledge of the constitution of the alloys had become seriously inadequate. To interpret correctly alloy behavior it is not only necessary to recognize the phases present, but also to know the properties of the phases under all varieties of conditions and treatments. Chromium in these high temperature alloys holds the unique distinction of being the only one element which must be present when an oxidizing or generally corrosive atmosphere is present and when a long life is desired in service. Carbon and nitrogen must also be considered where chromium is present. Carbon is always present, either as an impurity in the raw alloying elements, or as a deliberate addition agent to increase the strength. Nitrogen is generally picked up from the atmosphere during melting or may be added as an alloying element. The effect of nitrogen additions is not too dissimilar to that of carbon additions. As such, chromium carbides and nitrides become of great interest since they are present in a very large number of alloys, including alloy steels, stainless steels, super alloys, and the like. In the chromium-carbon system there are three accepted, carbides: Cr,C, Cr7C8, and Cr3C2. The existence of one more carbide, a still higher carbon form CrC, has been advanced. The phase diagrams of chromium and carbon as published by Friemann and Sauerwald² and by Tofaute, Kuttner and But- tinghaus³ -do not extend beyond the carbide Cr3C2, which contains 13.3 pct carbon; but Hatsuta has extended the diagram up to 20 pct carbon, and in doing so hypothesized, with the use of some questionable experimental results, the compound CrC. This carbide would contain 18.75 pct carbon, 81.25 pct chromium, by weight. It is further known that as the chromium carbides increase in carbon the acid resistance increases but the oxidation resistance decreases4,5 This is of great importance in high temperature alloys where time-temperature stability, as well as oxidation resistance, is of prime importance. The possible existence of a carbide of the formula CrC thus becomes of prime importance and it was considered important to recheck the chromium-carbon binary constitutional diagram for such a compound. In view of the wide spread of values listed for the melting point of chromium (1500° to 1850°C) and 1930°C8, it was considered .that the liquidus temperatures might well be redetermined more ac-

Jan 1, 1951

By William Kent

William Kent, Pi.~t~bIJrQh, Pa.: The steel rnanufac.tnret of this country nlust ever he grateful to Dr. Dudley for his painstaking and conscientious endeavor to estaldish the relation between the chemical analysis and the wearing capcity of steel rails. They tnust thank him for the vast array of $acts he presents, and for having given them sixty-four analyses with which to combat his own conclusions and to establish their own, which are entirely opposite to his. In Dr. Duclley" discussion of his former investigation, at the Pittsburgh meeting, he said, "If you do not like my conclusions, draw your own conclusions." I have studied his last paper as thoroughly as the limited time since I received it would adruit, and have drawn some concluvions which I will first state, and then attempt to demonstrate. Briefly stated, my conclusions are: lst, That as far as these 64 analyses reveal anything of service to railmakers and cotsumera, it is that within the following chemical and physical limits, viz., Carbon,..0.20 to 0.60 Pisovphorue ,..0.026 to 0.146 Silicon,.. 0015 to 0.480 BInnganese.......0.262 to 0 880 Phosl~horus un~ts,..20.3 to 6.72 Bending weight,. 2270 lbs. to 4260 Ibs. Drfl~ctinn,.. 13O to 190° or in other words within the limits of rienrly the whole range of the chenlical and bending testa of these 6-2 mils: the wearing capacity bears no relation at all to mrbon, to phosphorus, to silicon, to mnnganese, to phosphorus units, to bending weight or to deflection or if there is any relation between the wearing capacity and thest! six or sr!ven variables, it is so obscured by the action of other cause or variat~les not yet known, that such relation cannot be expressed by any practical formula. 2d. That the difference in wearing capacity of these 64 rails was not due to unrbon, to phosphorus, to silicou, to manganese, or to anj combinntion of these four elements, but that it was due to some other cause or cornbination of causes, of which Dr. Dudley's whole iuvestigtion furnishes 11s no clue whatever. A few of the nlarry possible causes I lnay name : sulphur, copper, oxide of iron inclossl air or other gases, orerblowing, underblowing, oyrhaiting, undcrIreatinp, too hot-finishing, too cold-finishing, cold-straightening, toc great or too litkle rductiun hlu the rail to the ingot, or the portion

Jan 1, 1881

By D. E. Etter, J. E. Selle

The Pu-Ce phase diagram was determined by differential thermal analysis, metallography, and elechm-nricroprobe analysis. The dingram is chararterized by a eutectic with extensive solid solubility in the cubic Phases of both cerium and plutonium. No intermediate phases were found. Cerium is soluble in e plutonium to 16.0 at. pet Ce at 626OC nnd in d plcltoniurn to 23.0 at. pet at 613 "C, decreasing to 17.5 at. pet at room temperature. No solubility in the a, ß, or ? phases was jound, and the mininum cerium required to stabilize 5 plutonium to room temperature is 3.2 at. pet. The maximum solubility of plutonium in 6 cerium is 19.5 at. pet at 721OC, and the maximum soluhility of plutonium in ? cerium is 34.5 at. pet. Invariant points in the system are: a) eutectic at 626oC, L16.5 = E Pu16.0 + y Ce65.5; b) peritectoid at613oC, e Pu13.5 -y Ce65.5- d Pu23.0. AS part of a program aimed at the determination of the phase equilibria in the Pu-Ce-Cu ternary system, preliminary investigations were made of the three binary systems. A survey of the Pu-Ce binary system by differential therma1 analysis indi- cated several areas of disagreement with the published diagram,' primarily in the shape of the liquidus surface. Consequently, a thorough investigation of the system was undertaken, and this report presents the results of the study. EXPERIMENTAL PROCEDURE Three methods of investigation were used: differential thermal analysis (DTA), metallography, and analysis with electron-microprobe X-ray analyzer (EMX). The EMX analysis was particularly useful for the determination of solvus lines. The DTA method was most useful for the determination of the liquidus curves. Metallography complemented both of these techniques. Materials. The cerium metal used for most of this work had a freezing point of 805°C. This material showed 15°C premelting, and was found metallographically to contain some unidentified in~lusions.2 The temperature of premelting is defined as the point at which the DTA curve breaks away from the base line, analogous to a curve obtained from a solid-solution alloy. Several compositions were prepared near the cerium end of the diagram with higher-purity material which had a freezing point of 800°C. etallographic analysis showed this material to be relatively free of inclusions and only 8°C premelting was observed. Major impurities were found by spectrographic

Jan 1, 1964

By R. I. Parsons, M. B. Standing, E. N. Lindblad

The recovery of the heavier components from a gas cap or retrograde pool is shown to be the greatest when the sand is cycled with a dry gas at a low pressure. This conclusion is in direct opposition to the belief that the most efficient production program is pressure maintenance and cycling at or near the dew point. The results are calculated from: (I) constant volume, variable composition pressure-volume-temperature tests on a mixture of trap gas and liquid from a producing well; (2) published equilibrium constant data and the measured composition of the dew-point material; and (3) the fact that in a sand section of homogeneous permeability, injected gas displaces reservoir gas nearly, quantitatively. The results are based on the simplifying assumption that variable permeability systems may be defined by the ratio of two statistical parameters, and that gas injected into an actual sand will behave as though the sand were composed of many layers, each of constant permeability. Introduction Pressure decline in gas-condensate type reservoirs is accompanied by the formation of a liquid phase throughout the reservoir. Over the past ten years the processing of the material from these types of reservoirs for the heavier hydrocarbon components and the return of the light fractions to the reservoir ("cycling") has become increasingly popular. It has often been stated that the purpose of such a program is to prevent the loss of the retrograde liquid phase formed in the reservoir. The purpose of this paper is to present the results of laboratory tests and computations concerned with several possible methods of producing a gas cap or condensate type of reservoir. The results show that the recovery of heavier hydrocarbons for this type of reservoir is not a maximum under conditions of cycling at or near the dew-point pressure. Instead, variations in permeability and the ability of the dry injected gas to revaporize condensate, point to cycling at a considerably reduced pressure as the optimum production-method. In addition the paper suggests a way of evaluating sands for their permeability variation. The calculations presented in the following sections of the paper are in terms of the production of the butanes and heavier fraction from the gas cap of a field which had an original pressure of approximately 3000 psi. Specifically, the calculations show: 1. To what extent the condensate formed in the reservoir after pressure decline can be recovered by the cycling of a dry absorber-plant gas through the sands. 2. Whether there would be greater recovery of hydrocarbons if cycling were instigated at the original reservoir pressure.

Jan 1, 1948

By M. B. Standing, R. I. Parsons, E. N. Lindblad

The recovery of the heavier components from a gas cap or retrograde pool is shown to be the greatest when the sand is cycled with a dry gas at a low pressure. This conclusion is in direct opposition to the belief that the most efficient production program is pressure maintenance and cycling at or near the dew point. The results are calculated from: (I) constant volume, variable composition pressure-volume-temperature tests on a mixture of trap gas and liquid from a producing well; (2) published equilibrium constant data and the measured composition of the dew-point material; and (3) the fact that in a sand section of homogeneous permeability, injected gas displaces reservoir gas nearly, quantitatively. The results are based on the simplifying assumption that variable permeability systems may be defined by the ratio of two statistical parameters, and that gas injected into an actual sand will behave as though the sand were composed of many layers, each of constant permeability. Introduction Pressure decline in gas-condensate type reservoirs is accompanied by the formation of a liquid phase throughout the reservoir. Over the past ten years the processing of the material from these types of reservoirs for the heavier hydrocarbon components and the return of the light fractions to the reservoir ("cycling") has become increasingly popular. It has often been stated that the purpose of such a program is to prevent the loss of the retrograde liquid phase formed in the reservoir. The purpose of this paper is to present the results of laboratory tests and computations concerned with several possible methods of producing a gas cap or condensate type of reservoir. The results show that the recovery of heavier hydrocarbons for this type of reservoir is not a maximum under conditions of cycling at or near the dew-point pressure. Instead, variations in permeability and the ability of the dry injected gas to revaporize condensate, point to cycling at a considerably reduced pressure as the optimum production-method. In addition the paper suggests a way of evaluating sands for their permeability variation. The calculations presented in the following sections of the paper are in terms of the production of the butanes and heavier fraction from the gas cap of a field which had an original pressure of approximately 3000 psi. Specifically, the calculations show: 1. To what extent the condensate formed in the reservoir after pressure decline can be recovered by the cycling of a dry absorber-plant gas through the sands. 2. Whether there would be greater recovery of hydrocarbons if cycling were instigated at the original reservoir pressure.

Jan 1, 1948

By Albert C. Harding

FOR several years barite (BaSO4) production has topped such better known minerals as feldspar and fluorspar in annual tonnage and is now well established among our foremost nonmetallic industries. DESCRIPTION Of widespread occurrence in the United States, barite is relatively soft (hardness, 2.5 to 3.5), inert, heavy (specific gravity, 4.5), and is also called "barytes" (sometimes pronounced "bear-i-tease"), "heavy spar" and "tiff." It occurs with granular and earthy structure but usually has coarse, orthorhombic crystallization. It is commonly white, and although occurring in various shades of red, yellow, and gray, barite always gives a white streak and can be scratched by the ordinary prospecting pick. Its softness and weight are usually sufficient to establish field identification. Another aid is the "rotten egg" odor of H2S which sometimes emanates from freshly fractured surfaces. Barite can be readily distinguished from two other minerals which have somewhat similar occurrences and characteristics. The relatively rare celestite, strontium sulphate, has a specific gravity slightly less than 4.00 and gives a distinctively crimson color in a flame test. The very rare witherite, barium carbonate, has a specific gravity of 4.3 but readily effervesces with dilute hydrochloric acid. OCCURRENCE All known commercially important barite deposits in the United States occur as re placements or cavity fillings in schists, shales, limestones, dolomites, and quartzites, or as residual deposits from such formations. In Georgia, Tennessee, North Carolina, and Missouri, high-grade barite is recovered as fragments from residual clays covering quartzites and dolomites. In Arkansas, Nevada, and California, barite, usually of lower grade, is mined from replacement deposits. These seven states contributed the entire production reported by the U. S. Bureau of Mines for 1945 as given in Table I. [TABLE 1-Crude Barite Sold or Used by Producers in 1945 STATE SHORT TONS Arkansas260,660 Missouri225,467 Georgia110,393 Tennessee32,812 Nevada28,919 Other States37,811 Total 696,062] "Other States" included only California and North Carolina. Such a large part of this undistributed production came from California that that state probably outranked both Nevada and Tennessee. For the second consecutive year Arkansas was the leading producing state, particularly worthy of note because there was no commercial production of barite there prior to 1941 and because the entire production of Arkansas has come from one large deposit which is being operated by two companies. CONSUMPTION [The 1945 consumption as reported by the Bureau of Mines was: 482,442 tons as ground barite 139,288 tons in making lithopone 99,173 tons in producing barium -- chemicals Total 720,903 tons]

Jan 1, 1947

By Harold Markus, Gerhard Derge, Arthur Grobe

THE high corrosion resistance possessed by tin under most circumstances, combined with its generally satisfactory appearance and useful physical properties, has led to many and varied uses for the metal. These uses have been partly limited by the fact that tin is an expensive metal, therefore many applications have been developed in which tin has been employed in combination with lead, either by coating, as in tin-lined collapsible tubes, or by the formation of alloys containing various proportions of tin-rich and lead-rich phases, as terne plate. A detailed knowledge of the corrosion characteristics of the tin-lead couple therefore is of general interest and has become specially important at the present time, when every effort is being made to conserve tin as much as possible. The present study has been limited to carbonate solutions with a pH range from 8.4 to 11.2 so that the results may be related to earlier work on the corrosion of tin and its alloys.1-3,6 In these papers, the effects of a number of anion and cation additions to these solutions have been observed. APPARATUS AND METHOD The electrodes for the corrosion cell were cut from rolled sheet about 1/16 in. thick. The length of all specimens was held constant at 7 in., while the width was varied from ½ to 2 in. These electrodes were fastened to brass electrode supports, which were attached to rubber stoppers fitting into tall-type one-liter Pyrex beakers that contained the electrolyte. The lead electrodes were prepared from Omaha pig* and the tin was rolled from a slab of Chempur.† After cutting to size, the sheets were polished with No. I emery paper and cleaned with carbon tetrachloride. The edges, back and upper parts of the specimen were coated with a synthetic lacquer, which was supplemented with beeswax for the lead electrodes. The binding posts were coated with beeswax after the electrodes had been clamped. The pH of the electrolyte was controlled by adjusting the ratio of carbonate to bicarbonate. Approximately 600 ml. of electrolyte was used in each beaker. The entire assembly was placed in an oil bath thermostatically adjusted to operate at 30°C. ± 0.1°. Potentials were measured against a saturated calomel electrode connected to the cell by an agar-agar salt bridge. The carbonate solution used in the salt bridge was the same as that used in the corrosion cell. Currents were measured with a milliam-

Jan 1, 1942

By Gerhard Derge, Arthur H. Grobe, Harold Markus

The high corrosion resistance possessed by tin under most circumstances, combined with its generally satisfactory appearance and useful physical properties, has led to many and varied uses for the metal. These uses have been partly limited by the fact that tin is an expensive metal, therefore many applications have been developed in which tin has been employed in combination with lead, either by coating, as in tin-lined collapsible tubes, or by the formation of alloys containing various proportions of tin-rich and lead-rich phases, as tcrne plate. A detailed knowledge of the corrosion characteristics of the tin-lead couple therefore is of general interest and has become specially important at the present time, when every effort is being made to conserve tin as much as possible. The present study has been limited to carbonate solutions with a pH range from 8.4 to 11.2 so that the results may be related to earlier work on the corrosion of tin and its alloys. 1-3,6 In these papers, the effects of a number of anion and cation additions to these solutions have been observed. Apparatus and Method The electrodes for the corrosion cell were cut from rolled sheet about 1/16 in. thick. The length of all specimens was held constant at 7 in., while the width was varied from M to 2 in. These electrodes were fastened to brass electrode supports, which were attached to rubber stoppers fitting into tall-type one-liter Pyrex beakers that contained the electrolyte. The lead electrodes were prepared from Omaha pig* and the tin was rolled from a slab of Chempur.† After cutting to size, the sheets were polished with No. I emery paper and cleaned with carbon tetrachloride. The edges, back and upper parts of the specimen were coated with a synthetic lacquer, which was supplemented with beeswax for the lead electrodes. The binding posts were coated with beeswax after the electrodes had been clamped. The pH of the electrolyte was controlled by adjusting the ratio of carbonate to bicarbonate. Approximately 600 ml. of electrolyte was used in each beaker. The entire assembly was placed in an oil bath thermostatically adjusted to operate at 30°C. + 0.1". Potentials were measured against a saturated calomel electrode connected to the cell by an agar-agar salt bridge. The carbonate solution used in the salt bridge was the same as that used in the corrosion cell. Currents were measured with a milliam-

Jan 1, 1942

By Harold Markus, Arthur H. Grobe, Gerhard Derge

The high corrosion resistance possessed by tin under most circumstances, combined with its generally satisfactory appearance and useful physical properties, has led to many and varied uses for the metal. These uses have been partly limited by the fact that tin is an expensive metal, therefore many applications have been developed in which tin has been employed in combination with lead, either by coating, as in tin-lined collapsible tubes, or by the formation of alloys containing various proportions of tin-rich and lead-rich phases, as tcrne plate. A detailed knowledge of the corrosion characteristics of the tin-lead couple therefore is of general interest and has become specially important at the present time, when every effort is being made to conserve tin as much as possible. The present study has been limited to carbonate solutions with a pH range from 8.4 to 11.2 so that the results may be related to earlier work on the corrosion of tin and its alloys. 1-3,6 In these papers, the effects of a number of anion and cation additions to these solutions have been observed. Apparatus and Method The electrodes for the corrosion cell were cut from rolled sheet about 1/16 in. thick. The length of all specimens was held constant at 7 in., while the width was varied from M to 2 in. These electrodes were fastened to brass electrode supports, which were attached to rubber stoppers fitting into tall-type one-liter Pyrex beakers that contained the electrolyte. The lead electrodes were prepared from Omaha pig* and the tin was rolled from a slab of Chempur.† After cutting to size, the sheets were polished with No. I emery paper and cleaned with carbon tetrachloride. The edges, back and upper parts of the specimen were coated with a synthetic lacquer, which was supplemented with beeswax for the lead electrodes. The binding posts were coated with beeswax after the electrodes had been clamped. The pH of the electrolyte was controlled by adjusting the ratio of carbonate to bicarbonate. Approximately 600 ml. of electrolyte was used in each beaker. The entire assembly was placed in an oil bath thermostatically adjusted to operate at 30°C. + 0.1". Potentials were measured against a saturated calomel electrode connected to the cell by an agar-agar salt bridge. The carbonate solution used in the salt bridge was the same as that used in the corrosion cell. Currents were measured with a milliam-

Jan 1, 1942

By Franz R. Dykstra

DEFINITIONS The ores of iron are classified in three general categories: direct shipping, concentrates, and agglomerated-i.e., pelletized or sintered. Direct Shipping As the name implies, direct-shipping ores are shipped as mined or, perhaps, after screening. Generally, direct-shipping ores are hematitic (R203), magnetitic (R304), or limonitic (2Fe2O3.3H20) in nature. Grades of direct-shipping ores vary widely. Prices are frequently related to the historical Mesabi standard of 51.5% iron, although certain premium lump ores may contain up to 68% iron. The use of direct-shipping ores is diminishing as the advantages of beneficiated ores become evident and reserves are depleted. Concentrates Where the nature of the deposit and economics allows, certain ores are upgraded. This may include no more than washing and screening, or may be as elaborate as fine grinding followed by magnetic, gravity, or even flotation procedures for separation. Coarser concentrates may be smelted "as is.'; Fine concentrates usually are sold as sinter feed. (Sinter, as used here and in the following, refers to a process by which a fine ore-carbon mixture is agglomerated at elevated temperatures on a direct-fired moving grate to eliminate fines and improve chemical and physical homogeneity.) Agglomerates-Pellets or Sinter The development of economic techniques of mining and concentrating taconite (fine-grained, ferruginous jasperoids) led to the introduction of the iron-ore pellet, which is now becoming the major form in which iron is introduced into the furnace. The tremendous reserves of magnetic taconites of the northern United States and Canadian Precambrian shield had been recognized for many years. A century of mining has seen the reserves of the direct-shipping or "red ores" of the Minnesota, Michigan, and Wisconsin ranges approach depletion. Research started in the 1930s has seen the evolution of motives and techniques to concentrate these stubborn refractory ores. The efficacy of concentrate pellets in iron-making has been such as to induce mines throughout the world to grind, concentrate, and pelletize otherwise shipping-grade ores. Table 14.1A.1 shows typical analyses of iron ore. Marketing-Prices of iron may be quoted on a value per long-ton (2240 lbs) or metric-ton (1000 kg or 2204 lb) basis, or on a value per long-ton-unit or metric-ton-unit basis. One iron unit represents 1 % of contained iron per ton. (Thus, a price of $0.45 per iron unit for ore containing

Jan 1, 1976

By N. A. Gokcen, M. N. Dastur

In metallurgical process industries a knowledge of true melting and casting temperatures is very essential for increasing the operating efficiency as well as improving the quality of the finished product. Optical pyrometers are widely used for the purpose because of their cheapness and ease of operation. It is an unfortunate fact, however, that this mode of measuring temperature entails a source of severe error inasmuch as with all non-black bodies, the temperature observed is always below the true temperature owing to deficient emissive power. Hence, the need for emissivity correction arises. In 1913 Bidwell1 obtained emissivity values of 0.36-0.48 for a temperature range of 1520-1800°C. He measured the true temperature of molten iron by sighting into a carbon cavity immersed in the iron under an atmosphere of hydrogen. In 1914 Burgess2 determined the emissivity of a smooth surface of liquid iron free from oxide to be 0.37 under an atmosphere of hydrogen. He claimed to have attained an accuracy of within 5°C at 1500°C with an optical pyrometer using monochromatic light. He reported that no difference appeared to exist between the emissivities of pure iron and of steels containing considerable percentages of carbon, nickel or manganese; nor was there any appreciable variation of emissivity with temperature from 1530 to 1571°C. Wensel and Roeser3 found an elnissivity value of 0.4 for temperatures above 1375°C for cast iron. The average emissivity value for carbon steels reported by Leiber,4 odd,5 Hase6 and Umino7 range from 0.4 to 0.45. Knowles and Sarjant8 made an extensive study of emissivity of molten iron and steel over a wide range of workshop and laboratory conditions. Observations of true temperature were made with immersion thermocouples, and correlated with apparent temperatures indicated by optical pyrorneter readings taken on the pouring stream as it passed over the lip of the crucible. The emissivity of Armco iron was shown to be of the order of 0.4, rising slightly with increasing temperature. But for plain carbon steels containing up to 1.0 pct carbon the emissivity was shown to fall slightly with increasing temperatures. The results of their investigation are in agreement with those of Guthmann.9 Naeser,10 Spencer," Todd5 and Hase6 in regard to the relation between emissivity and temperature for plain carbon steels. However, Goller12 has found a rise of emissivity with increasing temperature for the same steels. Results of several investigations are given in Fig 1. Measurement of True and Apparent Temperatures The necessity for an accurate optical temperature scale for liquid iron in studies of gas-metal equilibria led to this investigation. Experimental measurements were carried out in the induction furnace used by Dastur and Chipman13 in their studies of the reaction of hydrogen with oxygen in liquid iron. The furnace as modified for this work is shown in Fig 2. The atmosphere of the furnace was a mixture of purified argon with hydrogen containing a small controlled amount of water vapor. Gases were preheated by means of a platinum-10 pct rhodium resistance coil. The stream of hydrogen sweeping across the surface of niolten iron vir-

Jan 1, 1950