Search Documents

By J. B. Newkirk, R. W. Hendricks, R. Baro

STUDIES of the kinetics of precipitation in binary alkali halide systems are of interest from a theoretical point of view, because of the possibility of controlling diffusion rates by additions of aliovalent impurities. This note reports some preliminary results of a study of the kinetics of precipitation of AgCl from supersaturated solid solutions of AgCl in NaCl containing trace amounts of divalent cation impurities. In their study of the system NaC1- AgC1, Stokes and Li1 derived the phase diagram containing a mis-cibility gap with a broad maximum at approximately 170°C. They found that single crystals quenched from above the miscibility gap and aged at various temperatures within the two-phase region gradually turned light blue, then cloudy white, and finally opaque. The rate of transformation depended markedly on the aging temperature. The light-blue color in the early stages of aging was interpreted to be the result of Rayleigh scattering from precipitated particles less than 0.1 µ in diameter. These qualitative observations have been confirmed by us. However, a more precise tool was needed in order to quantitatively follow the growth kinetics of the precipitate particles. Because of the suspected small size of the precipitate particles and for other reasons, small-angle X-ray scattering was thought to be a suitable technique for this study. Small-angle X-ray intensities scattered from powder specimens were recorded on a General Electric XRD-5 diffractometer using the four-slit geometry described by Neynaber, Brammer, and Beeman.2 The slits were 0.08 mm wide by 10.00 mm high. It was found that, with very careful alignment, meaningful data could be obtained to within 3 min from the middle of the direct beam. Chromium radiation (?Ka = 2.29Å) was used in order to spread the scattered intensity to a relatively high angle, as indicated by Eq. [1]. A specimen containing 21.0 at. pet AgCl was prepared by melting analytic reagent-grade AgCl and NaCl under a chlorine atmosphere in a vycor cap-

Jan 1, 1964

By H. G. Papacharalambous, S. C. Sun

Experimental results indicate that wet cyclones could be effectively used for the preliminary classification of the tested synthetic abrasive materials, thus supplementing the currently used sedimentation method. An empirical formula is also proposed on the basis of the test data to calculate the particle size of separation. One of the basic operations in the abrasive industry is the classification of the crushed and ground materials into different sized products. The relatively coarse grains, plus 325 mesh, are commonly sized by dry screening with satisfactory results. On the other hand, however, the currently used grading tank, for classifying grains finer than 325 mesh, is intermittent. Consequently, it is difficult to operate efficiently and keep pace with erratic market requirements. Little success was made in an attempt to substitute air settling and continuous hydraulic settling for the grading tank, because size specifications1 for abrasive powders are very stringent and difficult to meet. Finally, a wet cyclone was chosen for experimentation. Even though wet cyclones have not been extensively used in the classification of abrasives; however, their performance as a classifier has been verified by Driessen2,4 on coal, McCarrel5 with manganese, and Herkenhoff6,7 on iron ore. Experimental work on silicon carbide, boron carbide, and fused alumina has shown that the cyclone

Jan 1, 1963

By Richard D. Call

In any open pit, some slope instability can be expected, varying from bench sloughing to large-scale slope movement. Major slope displacements are preceded by small, but measurable, displacements and by other indicators of instability, such as tension cracks, rock noise, and changes in groundwater levels. A comprehensive monitoring pro- gram, capable of measuring and assimilating displacement related data, is essential for sound pit operation. The objectives of a pit slope monitoring program are 1) to maintain safe operational procedures for the protection of personnel and equipment; 2) to provide advance notice of instability so that mine plans can be modified to minimize the impact of slope displacement; and 3) to provide geotechnical information for analyzing the slope failure mechanism, for designing appropriate remedial measures, and for conducting future re-design of the slope. Surface displacement measurement using conventional survey equipment and extensometers has been the most widely used method, and it is still the most cost-effective. Tiltmeters and borehole inclinometers are also useful tools, and there are promising developments in micro- seismic monitoring. A monitoring system should have redundancy in both type and number of measurements, and be capable of rapid and effective dissemination of displacement information to those affected.

Jan 1, 1983

By Robert A. Cummings, Francis S. Kendorski

The behavior of the rock mass during block caving affects the production of the mine and dictates the loads and deformations placed on required drifts. Traditionally, the drifts used are massively reinforced and buttressed against very high and erratic mining- induced abutment loads or swell muck loads, resulting from undercut- ting. Extensive field investigations in numerous block caving mines in the porphyry intrusive environment, coupled with models developed for tunneling and longwall coal mining, have allowed the development of a unified hypothesis for ore bodies of various degrees of competence. In general, the hypothesis incorporates several sequential steps in the driftlrock mass deformation history, each with characteristic magnitudes, duration, and areal extents depending on ore body competence. 1. Prior to initiating caving, but subsequent to drift development, the rock mass and drift are in a state of near-equilibrium. Zones of stress concentration have stabilized, as for a tunnel. 2. For a newly undercut panel, the rock mass and drifts directly beneath the undercut respond by dilating towards the void created, and undergo a release of compressive strain that manifests itself as tensile failures. 3. For adjacent areas, the rock mass is compressed as the load is shed from the undercut level.

Jan 1, 1983

At its meeting on February 21, 1933, the Board of Directors passed the following resolution defining and expressing the policy of the Institute with respect to official participation or action in controversial matters: WHEREAS, the Board of Directors at its last meeting passed the following resolution: "The Board of Directors, having been appealed to by several Local Sections for advice concerning the attitude and policy of the Institute relating to the endorsement of candidates for public office, the following statement of policy is formulated: "Whereas, the American Institute of Mining and Metallurgical Engineers is organized for purely professional and scientific purposes, and whereas diversity of opinion among its members on partisan or political questions is inevitable, it is the expressed policy of the Institute to refrain from official participation or action in political and semi-political matters." AND WHEREAS, appeals for additional advice have been received: NOW, THEREFORE, IT IS RESOLVED: (1) That the policy of the Institute is to refrain from official participation or action in controversial non-technical economic subjects; further (2) That if any Local Section is in doubt as to the application of this policy to any particular subject, it should communicate with the Secretary of the Institute for advice.

Jan 1, 1940

At its meeting on February 21, 1933, the Board of Directors passed the following resolution defining and expressing the policy of the Institute with respect to official participation or action in controversial matters: WHEREAS, the Board of Directors at its last meeting passed the following resolution: "The Board of Directors, having been appealed to by several Local Sections for advice concerning the attitude and policy of the Institute relating to the endorsement of candidates for public office, the following statement of policy is formulated: "Whereas, the American Institute of Mining and Metallurgical Engineers is organized for purely professional and scientific purposes, and whereas diversity of opinion among its members on partisan or political questions is inevitable, it is the expressed policy of the Institute to refrain from official participation or action, in political and semi-political matters." AND WHEREAS, appeals for additional advice have been received: NOW, THEREFORE, IT IS RE¬SOLVED: (1) That the policy of the Institute is to refrain from official participation or action in controversial non-technical economic subjects; further (2) That if any Local Section is in doubt as to the application of this policy to any particular subject, it should communicate with the Secretary of the Institute for advice.

Jan 1, 1946

IN presenting the medalist, Scott Turner, director of 'the Bureau of Mines, said in part: "Mr. Blaylock is a Canadian by birth, training, ex-perience and preference. He was born in the Province of Quebec, graduated from McGill University in 1899, and immediately thereafter became an employee of the company for which he is now general manager. His outstanding achievements have been the acquisition for his company of the Sullivan mine, and the organization of a metallurgical staff, which, under his leadership and personal direction, solved the difficult problems pre-sented by the extraordinarily complex lead-zinc-silver ores of the Sullivan mine. "By title only, I will suggest to you the high lights of his career: (1) Development, of the great mine at Kimberley, and a huge plant at Trail. (2) Discovery and application of a successful differential flotation process for Sullivan ore which had previously not re-sponded to any process. (3) Improvements in lead-blast-furnace and refinery practice. (4) Development of an electrolytic process for treatment of zinc concen-trates. (5) Development of an electric-furnace-smelt-ing-method for zinc-plant residues. Besides this, we recognize his great organizing ability, his gift of leader-ship, and the cooperative spirit he always displayed.

Jan 3, 1928

By Frank H. Armstrong

All the mining machinery of the Penn Iron Mining Co. has been operated by electric power for several years and when another shovel for stockpile loading was required the advantages of an electric shovel were naturally considered. After considerable study, serious objections suggested themselves the use of a shovel operated directly by electrical apparatus by reason of the complicated control, severe service on the motors and the heavy surges of current required from the line. It was finally decided to construct an electro-hydraulic shovel using water under pressure to perform all the necessary operations except that of propelling, for which a separate motor was best suited. A car body with boom, dipper handle and dipper of late design, but without any of the steam machinery, was purchased. A motor-driven centrifugal pump, a pressure tank, an air tank, a small air compressor and water cylinders with plungers, pistons and valves, were installed in place of the steam equipment. Fig. 1 shows this shovel under construction and Fig. 2 shows it as it was operated during the first year, the summer of 1914. The large tank at the back of the car, in Fig. 1, carried air under

Jan 1, 1916

By William Y. Warren

Messrs. Thomas & Cross, having leased from the Akron Cement Company from twelve to fifteen acres of abandoned cement-tunnels and chambers, for the purpose of propagating mushrooms for the market, commenced operations about a year ago, and are now beginning to furnish mushrooms in quantities to the local markets of Buffalo and Rochester. The quarries, or, more properly, the mines, of the Cement Company are located at Akron, Erie County, PIT. Y. The cement-rock occurs in a stratum about 71/2 to 8 feet in thickness, which is overlain by from 1.5 to 25 feet of limestone and flint-rock. There is a gentle rise from the opening of the tunnel inwards, giving a natural drainage and leaving the chambers comparatively dry. The roof is good and is supported by pillars and heavy timbers. The mushroom-beds are located about 300 feet from the opening of the tunnel, and are made in the form of mounds about 3 feet by 12 feet, at the base, and 24 feet high, giving to the chambers the appearance of a subterranean graveyard. Many experiments have been made to determine the best form for the beds, and the mound

Jan 1, 1889

By T. Federighi, S. Ceresara, C. Panseri

The results of an exploratory investigation by means of resistivity measurements at -195ºC, on the aging characteristics of a set of Al-Mg alloys with a maximum content of 7 pct Mg, are reported. Whereas for dilute alloys (Mg < 1.5 pct) only a decrease in resistivity is observed at about 100°C (due to the elimination of quenched-in vacancies), for more concentrated alloys such a decrease is preceded by an increase in resistivity in the range between -60ºand +40°C. Following some previous suggestions, this increase is considered as good evidence for clustering of solute atoms @reprecipi-tation process). From the analysis of the results it appears that, although the process is substantially similar to that observed in other Al-rich alloys, it is characterized by a strong interaction between vacancies and zones. THE process of formation of Guinier-Preston zones, i.e., preprecipitation,1&apos;2 which occurs during the aging at about room temperature in many supersaturated aluminum-rich alloys, has been extensively investigated in the past few years by several workers.2,3 owever, a very interesting question arises when the case of Al-Mg alloys is considered: although it is very easy to supersaturate Al-Mg alloys, just in the same way as for many other aluminum alloys showing preprecipitation, only very little experimental evidence was available until a short time ago in the literature supporting the existence of "natural" aging in supersaturated Al-Mg alloys (see, for example, Refs. 4 to 6). On the other hand, as is well known, the X-ray method is not useful in this case because the X-ray scattering factors of magnesium and aluminum atoms are about the same. Recently, however, Cordier and Detert7 have stressed that during the aging at about room temperature of a supersaturated Al-Mg 10 pct alloy it is possible to detect an increase in resistivity; since, as is well known, such an increase is observed also in most alloys showing preprecipitation, the above authors have interpreted their results as evidence for the formation of magnesium-rich clusters (or Guinier-Preston zones) during the aging. In the course of or ientative investigations on preprecipitation in several aluminum-rich alloys, we also could detect a similar phenomenon in more dilute Al-Mg alloys, see Instituto Sperimentale Metalli Leggeri, Annual Report, 1959, and also Ref. 8. Since the details of our observations, although of a preliminary nature, differ from those of Cordier and Detert and allow one to draw a more advanced picture of the preprecipitation process in Al-Mg alloys, we have thought it useful to report our results in this paper and to comment on them briefly.

Jan 1, 1963

By C. M. Loeb, T. E. Norman

The use of ball, rod and tube mills for grinding ore, cement and other materials has grown so rapidly during the past forty years that the world&apos;s annual consumption of ferrous grinding media for these mills is now estimated to be between one half million and one million tons per year. Ferrous grinding balls constitute the major portion of this tonnage. Obviously they represent sufficient value to justify thorough studies of the factors governing their performance. The selection of grinding balls is governed principally by: I. Quality (wear resistance, impact resistance, soundness, and the like). 2. Sources of supply and delivered cost. 3. Grinding characteristics or efficiency in the ball mill. This paper deals principally with the quality of ferrous grinding balls. In the study of these factors certain data relative to the fundamental nature of ball wear in ball mills have been obtained. These data are also presented and discussed briefly. The Development of a Suitable Wear Test A study of the fundamental factors governing the quality of grinding balls has been hampered seriously by the fact that a competent test has, in the past, involved the purchase of several hundred tons of balls of a specific type which were then run in one or more ball mills for a period ranging from several months&apos; to several years&apos; duration. Often, during the period of test, it became necessary to change operating conditions or the character of the ore fed to the test mill with the result that the rate of ball consumption changed and the test figures became of little value. Under such circumstances, progress in the development of better grinding balls, has been necessarily slow. Economic factors and variations in the quality of balls produced by different sources of supply generally make it necessary for each mill operator to determine for himself the most suitable type of balls for his mills. In our own ball mill grinding operations at Climax, Colo., we were faced with this problem. After we had run a few large scale wear tests at considerable expense we decided to investigate the possibilities of a small scale wear test which would be capable of testing numerous types of balls within a relatively short time. The most important requirement of any test is, of course, that it give results which can be used to predict accurately the wear in full scale operations. It was known that Ellis and his associates1,2 had developed a method of testing grinding balls by small scale tests run at the Ontario Research Foundation. Ellis&apos; method of testing was used as a starting point in our investigations. In the course of our tests a number of modifications of the original method were found to be desirable so that, by an evolutionary procedure, a method of small scale

Jan 1, 1949

By C. M. Loeb, T. E. Norman

THE use of ball, rod and tube mills for grinding ore, cement and other materials has grown so rapidly during the past forty years that the world&apos;s annual consumption of ferrous grinding media for these mills is now estimated to be between one half million and one million tons per year. Ferrous grinding balls constitute the major portion of this tonnage. Obviously they represent sufficient value to justify thorough studies of the factor sgoverning their performance. The selection of grinding balls is governed principally by: I. Quality (wear resistance, impact resistance, soundness, and the like). 2. Sources of supply and delivered cost. 3. Grinding characteristics or efficiency in the ball mill. This paper deals principally with the quality of ferrous grinding balls. In the study of these factors certain data relative to the fundamental nature of ball wear in ball mills have been obtained. These data are also presented and discussed briefly. THE DEVELOPMENT OF A SUITABLE WEAR TEST A study of the fundamental factors governing the quality of grinding balls has been hampered seriously by the fact that a competent test has, in the past, involved the purchase of several hundred tons of balls of a specific type which were then run in one or more ball mills for a period ranging from several months to several years&apos; duration. Often, during the period of test, it became necessary to change operating conditions or the character of the ore fed to the test mill with the result that the rate of ball consumption changed and the test figures became of little value. Under such circumstances, progress in the development of better grinding balls, has been necessarily slow. Economic factors and variations in the quality of balls produced by different sources of supply generally make it necessary for each mill operator to determine for himself the most suitable type of balls for his mills. In our own ball mill grinding operations at Climax, Colo., we were faced with this problem. After we had run a few large scale wear tests at considerable expense we decided to investigate the possibilities of a small scale wear test which would be capable of testing numerous types of balls within a relatively short time. The most important requirement of any test is, of course, that it give results which can be used to predict accurately the wear in full scale operations. It was. known that Ellis and his associates1.2 had developed a method of testing grinding balls by small scale tests run at the Ontario Research Foundation. Ellis&apos; method of testing was used as a starting point in our investigations. In the course of our tests a number of modifications of the original method were found to be desirable so that, by an evolutionary procedure, a method of small scale

Jan 1, 1948

By S. F. Urban, G. Derge

At the time this investigation was initiated variations were observed in the quality of different heats of basic electric-furnace steels, although they had been made under purportedly similar conditions. This indicated that these variations were related to normally unobserved variations in the character of the bath, especially during the "refining" period. Although the slags used for this operation are commonly referred to as "reducing" slags, and are regarded as having a "deoxidizing" action on the bath, no reliable measurements of this action were available. It was decided, therefore, to study the behavior of oxygen in the metal for &apos; large enough number of heats to learn its normal variations and to relate these variations to regularly observed conditions of operation. The most important general conclusion reached was that the time a heat is held under a reducing &apos;lag should be reduced to a minimum, which was about an hour and a half under the conditions studied. Beyond this time no observable beneficial effects are obtained from the reducing slags, insofar as oxygen and sulphur content of the bath are concerned. It is likely that added time may increase hydrogen content as well as heat costs. The oxygen content of the bath is never reduced below the amount in equilibrium with the carbon. Concurrently with this work, J. S. Marsh1 presented data that supplement and support many of the results of this paper. Procedure The work was done in two different electric-furnace shops of the same plant. The selection of heats was made primarily with regard to the convenience of heat schedules. companion slag and metal samples were taken just prior to slag-ofi and throughout the refining period for an initial set of 17 heats, and before slag-off and near tap for an additional I3 heats. slag Sampling presented no particular problem; a spoonful of slag was poured onto a metal plate and when sufficiently cool was sealed in an airtight container. Sampling the metal for oxygen presented a more complex problem. Because of the lack of previous experience in sampling electric-furnace baths, a number of methods were compared. Chilled Wedge Samples2 An unkilled metal sample is removed from the furnace in a well-slagged car-bometer spoon and poured immediately into a heavy copper mold designed to provide rapid freezing. Three different types of molds were used to determine the optimum for electric-furnace hats. The Big wedge Mold (a) was a 4 by 4 by 4-in. split copper mold, yielding a wedge-shaped casting I in. wide, 1 1/2 in. long, and 34 in. maximum thickness, and was finally adopted as the most satisfactory design.

Jan 1, 1948

By S. F. Urban, G. Derge

At the time this investigation was initiated variations were observed in the quality of different heats of basic electric-furnace steels, although they had been made under purportedly similar conditions. This indicated that these variations were related to normally unobserved variations in the character of the bath, especially during the "refining" period. Although the slags used for this operation are commonly referred to as "reducing" slags, and are regarded as having a "deoxidizing" action on the bath, no reliable measurements of this action were available. It was decided, therefore, to study the behavior of oxygen in the metal for &apos; large enough number of heats to learn its normal variations and to relate these variations to regularly observed conditions of operation. The most important general conclusion reached was that the time a heat is held under a reducing &apos;lag should be reduced to a minimum, which was about an hour and a half under the conditions studied. Beyond this time no observable beneficial effects are obtained from the reducing slags, insofar as oxygen and sulphur content of the bath are concerned. It is likely that added time may increase hydrogen content as well as heat costs. The oxygen content of the bath is never reduced below the amount in equilibrium with the carbon. Concurrently with this work, J. S. Marsh1 presented data that supplement and support many of the results of this paper. Procedure The work was done in two different electric-furnace shops of the same plant. The selection of heats was made primarily with regard to the convenience of heat schedules. companion slag and metal samples were taken just prior to slag-ofi and throughout the refining period for an initial set of 17 heats, and before slag-off and near tap for an additional I3 heats. slag Sampling presented no particular problem; a spoonful of slag was poured onto a metal plate and when sufficiently cool was sealed in an airtight container. Sampling the metal for oxygen presented a more complex problem. Because of the lack of previous experience in sampling electric-furnace baths, a number of methods were compared. Chilled Wedge Samples2 An unkilled metal sample is removed from the furnace in a well-slagged car-bometer spoon and poured immediately into a heavy copper mold designed to provide rapid freezing. Three different types of molds were used to determine the optimum for electric-furnace hats. The Big wedge Mold (a) was a 4 by 4 by 4-in. split copper mold, yielding a wedge-shaped casting I in. wide, 1 1/2 in. long, and 34 in. maximum thickness, and was finally adopted as the most satisfactory design.

Jan 1, 1948

By J. P. Hirth, G. M. Pound

The flux of evaporation J from {loo) , {111), and (110) planes of silver single crystals and from poly crystalline specimens was measured at 744°C under a high vacuum using a time average weight loss method. The evaporation coefficient a was computed from the measured flux and vapor pressure data through the relationship J = aPe/21rmkT. The evaporation coefficients for the close packed planes and the poly crystalline specimens were found to be about 0.4 providing tentative confirmation of the theoretical limiting law for evaporation of metal crystals, a = 73(P/Pe) + % . The (110) planes faceted to form (111) planes, resulting in a greater evaporating area and larger a . The evaporation morphology of the plane surfaces and the surfaces of spherical single crystals is described in some detail. RECENTLY a detailed theoretical analysis of the mechanism and kinetics of metal crystal evaporation was made.1&apos;2 A mechanism for vaporization involving the recession of monatomic ledges across a metal surface was deduced, and evaporation rate equations were derived by considering the dynamics of these ledges. In most metals, the process of evaporation is one of dissociation of atoms from ledges, surface diffusion, and desorption. The gross vaporization rate is controlled by the surface diffusion and desorption rates. It was shown that the monatomic ledges, under the action of surface diffusion gradients, tend to assume a terminal velocity and spacing. Further, it was shown that crystal edges and grain boundaries are a ready source for monatomic ledges. In the case of evaporation of large, perfect crystals with clean, low-index surfaces, the kinetic treatment1 leads to a limiting law for crystal evaporation: where J is the gross flux of vaporization, a is the evaporation coefficient, Pe the equilibrium vapor pressure, m the atomic mass, k Boltzmann&apos;s constant, T the absolute temperature, and P the actual pressure of vapor over the crystal surface. Imperfections such as grain boundaries, pores, cracks, and macroscopic steps should have the effect of causing positive departures from this limiting law. Such an imperfection is a source for monatomic ledges, which, near their origin, are closely spaced and thus give rise to higher evaporation rates there. However, under many experimental conditions,&apos; this effect should be negligible due to the relatively low concentration of imperfections. In general, a more important cause of positive departure should be screw dislocations, and the effect of these has been considered in some detai1.2,3 Monatomic ledges emanate from points where the surface is intersected by a dislocation with a screw component normal to the surface. The dynamics of ledges arising from a screw dislocation are similar to those of ledges arising from a crystal edge. There is a perturbed region near the origin where the monatomic ledges are, under certain experimental conditions, closely spaced and the

Jan 1, 1960

By J. H. Henderson, J. Naar

The displacement of a wetting fluid from a porous medium by a non-wetting fluid (drainage) is now reasonably well understood. A complete explanation has yet to be found for the analogous case of a wetting fluid being spontaneously imbibed and the non-wetting phase displaced (imbibition). During the displacement of oil or gas by water in a water-wet sand, the porous medium ordinarily imbibes water. The amount of oil recovered, the cost of recovery and the production history seem then to be controlled mainly by pore geometry. The influence of pore geometry is reflected in drainage and imbibition capillary-pressure curves and relative permeability curves. Relative permeability curves for a particular consolidated sand show that at any given saturation the permeability to oil during imbibition is smaller than during drainage. &apos; Low imbibition permeabilities suggest that the non-wetting phase, oil or gas, is gradually trapped by the advancing water. This paper describes a mathematical image (model) of consolidated porous rock based on the concept of the trapping of the non-wetting phase during the imbibition process. The following items have been derived from the model. 1. A direct relation between the relative permeability characteristics during imbibition and those observed during drainage. 2. A theoretical limit for the fractional amount of oil or gas recoverable by imbibition. 3. An expression for the resistivity index which can be used in connection with the formula for wetting-phase relative permeability to check the consistency of the model. 4. The Iimits of flow performance for a given rock dictated by complete wetting by either oil or water. 5. The factors controlling oil recovery by imbibition in the presence of free gas. The complexity of a porous medium is such that drastic simplifications must be introduced to obtain a model amenable to mathematical treatment. Many parameters have been introduced by others in Iprogressing" from the parallel-capillary model to the randomly interconnected capillary models independently proposed by Wyllie and Gardner3 and Marshall4. To these a further complication must be added since an imbibition model must trap part of the non-wetting phase during imbibition of the wetting phase. Like so many of the previously introduced complications, this fluid-block was introduced to make the model performance fit the observed imbibition flow behavior. THE IMBIBITION MODEL ASSUMPTIONS The following assumptions are common to many two-phase models previously described. 1. The wetting characteristics of the medium are clearly defined. 2. When two fluids co-exist in the medium, the wetting phase will fill the smaller pores and the non-wetting fluid the bigger ones. 3. The pores have a circular cross section. 4. Apparent pore radii are related to the capillary pressure (drainage) by

By J. S. Kennedy, A. A. Lerew, C. M. Judson, G. L. Simard

DITHIOPHOSPHATE collectors are commonly used in the flotation of sulphide minerals. Studies of the interaction of a typical dithiophosphate collector with galena surfaces have been previously reported from. these laboratories." These fundamental studies were carried out by employing phosphorus labeled radioactive dithiophosphate. Radioactivity determinations then could be used to measure readily and accurately the small concentrations of dithiophosphate that, are present under conditions of flotation processes. Measurements were made on ground mineral, determining the amount sorbed indirectly from the concentrations in solution; and studies were also made with single crystals, determining the amount sorbed directly by counting the crystal surface. The rates, isotherms and reversibility characteristics of dithiophosphate sorption, the competition between phosphate and dithiophosphate for the mineral surface, and the exchange of sorbed dithiophosphate with dissolved dithiophosphate were studied. These studies have now been extended by sorption measurements in flotations with a Fagergren, machine. For this work, the selective flotation of galena and sphalerite from quartz was chosen, using ammonium di-(sec-butyl) dithiophosphate as. the collector, sodium cyanide as depressant for sphalerite, and copper sulphate as an activator for sphalerite. While the selective flotation of galena and sphalerite using a single dithiophosphate collector is not typical of flotation practice (two different collectors are generally used), it was found that a reasonably good separation could be obtained by using zinc sulphate with the sodium cyanide in the galena flotation and by cleaning the sphalerite concentrate or by carrying out the sphalerite. flotation in an alkaline medium. Data of practical importance on the distribution of collector between the concentrates, tailings, and solutions were obtained, particularly with regard to the effect of copper sulphate and sodium cyanide. In addition to the. selective flotation of galena and sphalerite from quartz, single flotations of galena-quartz and sphalerite-quartz mixtures were carried out, along with blank flotations on quartz alone. The present paper describes the results of these experiments. As in previous papers, the term sorption is used to designate uptake of collector by the mineral, without implication as to the nature of the processes involved. Experimental Materials: The mineral system was a ground synthetic mixture of galena, sphalerite, and quartz. The galena was from Galena, Kans., and contained 75 pct lead (theoretical 85.6 pct Pb for PbS); the sphalerite, from Ottowa County, Okla., contained 63 pct zinc (theoretical 67.2 pet Zn for ZnS) ; and the quartz from Klondike, Mo., analyzed as 99.97 pet SiO2. Sulphur labeled radioactive di-(sec-butyl) dithiophosphate was prepared from S82 supplied by the Oak Ridge National Laboratory on allocation from the U. S. Atomic Energy Commission. The synthesis consisted of precipitating barium sulphate, reducing the barium sulphate to barium sulphide, acidifying to form hydrogen sulphide, and oxidizing the hydrogen sulphide with iodine to elemental sulphur.

Jan 1, 1952

By C. M. Loeb, T. E. Norman

THE use of ball, rod and tube mills for grinding ore, cement and other materials has grown so rapidly during the past forty years that the world&apos;s annual consumption of ferrous grinding media for these mills is now estimated to be between one half million and one million tons per year. Ferrous grinding balls constitute the major portion of this tonnage. Obviously they represent sufficient value to justify thorough studies&apos; of the factor sgoverning their performance. The selection of grinding balls is governed principally by: I. Quality (wear resistance, impact resistance, soundness, and the like). 2. Sources of supply and delivered cost. 3. Grinding characteristics or efficiency in the ball mill. This paper deals principally with the quality of ferrous grinding balls. In the study of these factors certain data relative to the fundamental nature of ball wear in ball mills have been obtained. These data are also presented and discussed briefly. THE DEVELOPMENT OF A SUITABLE WEAR TEST A study of the fundamental factors governing the quality of grinding balls has been hampered seriously by the fact that a competent test has, in the past, involved the purchase of several hundred tons of balls of a specific type which were then run in one or more ball mills for a period ranging from several months to several years&apos; duration. Often, during the period of test, it became necessary to change operating conditions or the character of the ore fed, to the test mill with the result that the rate of ball consumption changed and the test figures became of little value. Under such circumstances, progress in the development of better grinding balls, has been necessarily slow. Economic factors and variations in the quality of balls produced by different sources of supply generally make it necessary for each mill operator to determine for himself the most suitable type of balls for his mills. In our own ball mill grinding operations at Climax, Colo., we were faced with this problem. After we had run a few large scale wear tests at considerable expense we decided to investigate the possibilities of a small scale wear test which would be capable of testing numerous types of balls within a relatively short time. The most important requirement of any test is, of course, that it give results which can be used to predict accurately the wear in full scale operations. It was known that Ellis and his associates1,2 had developed a method of testing grinding balls by small scale tests run at the Ontario Research Foundation. Ellis&apos; method of testing was used as a starting point in our investigations. In the course of our tests a number of modifications of the original method were found to be desirable so that, by an evolutionary procedure, a method of small scale

Jan 1, 1947

By J. Szekely

A rrlethod is presented for the estitnation of oxygen pickup by teettzed molten steel streams. Of the mechanisrt~s considered for oxygen absorption, physical entrainment appeared to be the most significant. The estent of this physical entrainment may be calculated by the application of boundary layer theory. It was found that the values of oxygen pickup thus predicted were in wry good agreement with data reported in the literature, in the case of short, well-defined metal streams. This entrainment model does not provide an adequate description of oxygen pickup by long streams, exoosed to external winds and where breakup of the streatn is likely. WheN molten steel is teemed into a mold or tundish it will absorb oxygen contained in its environment. Recently interest has been expressed in the measurement and possible prediction of the extent of this oxygen absorption: this interest owes its existence to two principal factors: a) the desirability of providing a quantitative assessment of the role played by the absorbed oxygen in impairing the quality of (vacuum degassed. stainless, or continuously cast) steel; b) the need for providing guidelines for stream protection methods. The purpose of this communication is to suggest a simple method for the prediction of oxygen absorption by continuous metal streams and to compare the predicted values with the data available in the literature. It is hoped that this method may provide at least an initial framework for the interpretation of additional data that might become available. FORMULATION Consider a continuous metal stream falling into a molten metal pool as depicted in Fig. 1. This system may absorb oxygen due to the following two mechanisms: 1) physical entrainment of gases (including oxygen) into the molten pool where reactions. thus absorption, will occur; 2) mass transfer (convec:tive diffusion) of oxygen to the metal stream. 1) Physical Entrainment. The physical entrainment may be calculated by using the concept of the diaplace-ttzent tlzickness of the laminar boundary layer, which will be stated briefly in the following.&apos; When a fluid flows past a solid surface, a portion of the fluid close to the surface is retarded due to fric-tional forces. This region in which the velocity of the fluid differs from that in the main stream is called the boundary layer. An illustration of this is given in Fig. 2 where it is seen that the thickness of the boundary layer increases as we move along in the x direction. In the laminar region, when Re, < 10&apos; the thickness of the boundary layer is given by the following relationship: f =4.64 Re;1" [1] where 61 is the boundary layer thickness, x is the length along the leading edge, Us is the velocity of the free stream, (i is the viscosity of the fluid (gas in this instance).

Jan 1, 1970

By Robert B. Fulton, Gill Montgomery

Fluorspar is the commercial name for fluorite, a mineral that is calcium fluoride, CaF2. The name, derived from the Latin word fluere (to flow), refers to its low melting point and its early use in metallurgy as a flux. It is the principal industrial source of the element fluorine. Cryolite, sodium aluminum fluoride, Na3AlF6, is a rare mineral which has been found in commercial quantities only in Greenland. The natural material has been supplanted by synthetic cryolite for its principal industrial use in the manufacture of aluminum. History Fluorspar was used by the early Greeks and Romans for ornamental purposes as vases, drinking cups, and table tops. Various peoples, including the Chinese and the American Indians, carved ornaments and figurines from large crystals. Its usefulness as a flux was known to Agricola in sixteenth century Europe. Fluorspar mining began in England about 1775 and at various places in the United States between 1820 and 1840. Production grew substantially following the development of basic open-hearth steelmaking, wherein it is used as a flux. Use was stimulated by growth of the steel, aluminum, chemical, and ceramic industries, particularly during World Wars I and II. Fluorocarbons entered the picture in 1931. The use of anhydrous hydrogen fluoride (HF) as a catalyst in the manufacture of alkylate for high octane fuel began in 1942. Differential flotation for separating fluorspar from galena, sphalerite, and common gangue minerals in the 1930s, and the application of heavy-media concentrating methods to the treatment of low-grade ores in the 1940s were outstanding technological advances that facilitated increased production. Recently, pelletizing and briquetting of flotation concentrates for use in steel furnaces and the development of flotation schemes for beneficiating ores containing abundant dolomite and barite have been major improvements in the industry. Uses of Fluorspar Fluorspar is used to make hydrogen fluoride, also called hydrofluoric acid, an intermediate for fluorocarbons, aluminum fluoride, and synthetic cryolite. It is used as a flux in the steel and ceramic industries, in iron foundry and ferroalloy practice, and has many minor specialized uses. Hydrogen fluoride (HF) is produced by reacting acid grade (97% CaF2) fluorspar with sulfuric acid in a heated kiln or retort to produce HF gas and calcium sulfate. After purification by scrubbing, condensing, and distillation, the HF is marketed as anhydrous HF, a colorless fuming liquid, or it may be absorbed in water to form the aqueous acid, usually 70% HF. Synthetic cryolite, organic and inorganic fluoride chemicals, and elemental fluorine are made from hydrofluoric acid. The acid itself is important in catalysis in the manufacture of alkylate, which is an ingredient in high-octane fuel for aircraft and automobiles, in steel pickling, enamel stripping, glass etching and polishing, and in various electroplating operations. The manufacture of one ton of virgin aluminum requires about 50 to 60 lb of fluorine content in synthetic cryolite and alumnium fluoride. This quantity, through improved technology and recovery practices, is being lowered significantly.

Jan 1, 1983