Search Documents

By F. D. DeVaney

IT is of great interest that the various organizations engaged in the search for a cheap and efficient agglomeration process for fine magnetite concentrates-essential if the taconites are to be utilized-have ended up with processes that are basically different. This paper describes the development and the present status of the shaft-type furnace as now utilized by the Erie Mining Co., which is managed by Pickands Mather & Co. The shaft furnace has always had an appeal to metallurgists because of the simplicity of the design and the possible low fuel consumption. Work done on pelletizing at the University of Minnesota Mines Experiment Station by E. W. Davis and his associates determined that it was possible to roll up fine magnetite concentrates in a balling drum, and that, if such balls were fired at a sufficiently high temperature, a hard, indurated pellet, well adapted for use in a blast furnace, could be made. Early furnaces had no heat recuperation and the heat consumption was in the order of 2 million BTU's per long ton.

Jan 3, 1958

By Edward C. Roper

Pegasus' Gold Ltd. operates two gold/silver heap leaching operations in the Little Rockies area of Montana. The Little Rockies has produced gold from underground operations on an intermittent basis from the 1880's to the early 1950's and from the open-pits on a continuous basis since 1979. Run-of-the-mine ore is drilled, blasted, sorted, loaded and hauled. The waste is dumped and compacted into 30 meter (100 foot) fills to be used for future leach pads. The leach pads have a central drain system and the impermeable membrane is constructed of bentonite and 30 mil PVC. The plants which have beenexpanded to 4900 Ipm (1300 gpm) capacity use the Merrill-Crowe process for gold and silver recovery. 4600 liters (1200 gpm) of the 9500 Ipm (2500 gpm) spray capacity is recycled through the old leach pads for upgrading before being processed. The gold/silver precipitate is smelted and the resultant dore' is shipped to a buyerhefiner. 1983 projected production is 2,177 kg (70,000 02s) of gold at a cost of less than $10/gm.

Jan 1, 1984

By D. E. Wolfson, D. A. Reynolds, F. W. Smith

IN 1948 the U. S. Bureau of Mines began a three- phase program to evaluate the extent and quality of U. S. coking coal: 1) a factual appraisal of known recoverable reserves in beds of mineable thickness, 2) a study of preparation characteristics, and 3) a study of carbonization properties. A previous paper presented the methods used in assessing reserves.' Although this investigation is only partly completed, data on coking properties of the Pittsburgh district coals are now available. The results are presented in this article. When coals are selected for manufacture of metallurgical coke more factors must be considered than for any other major use, as no basic industry requires coal of such high quality and uniformity. This is particularly true in the Pittsburgh district, where blast furnace practice is based on use of cokes from high quality coals. Although it is true that inferior coals are carbonized in other industrial areas, both here and abroad, the Pittsburgh coals are the best economically obtainable in the required tonnages, even though they are not the most desirable for metallurgical use.

Jan 3, 1957

By Robert F. Winkle

A detailed breakdown of mining costs, available to management on monthly and year-to-date bases, is mandatory for a controlled and efficient mining operation. A simple lump sum reporting of costs may indicate a profit or loss differential, but it does not allow an effective search for areas of possible cost reduction. Moreover, functional reporting is necessary on a timely basis so as to note trends of increasing costs In specific areas, which in turn allow possible preventive action by management. Definitive cost information helps to eliminate the tendency to overlook areas where cost Improvements can be made. A good cost control system points out salient operational weaknesses by: ( 1 ) allowing comparison of functional costs with similar costs of other mines and (2) pinpointing sudden increases over unit empirical costs within the organization. In general, the cost accounting structure is relatively uniform within large open pit mines, but surprisingly some systems will overlook the need for detailed breakout in comparatively high cost areas. In some other systems, unrelated costs will be lumped together, preventing careful analysis of cost accrual.

Jan 1, 1979

By Joseph Kuti

ROOF SUPPORT DEVELOPMENTS IN LONGWALL (1) European longwall mining technology developed towards its modern form in relatively deep mines. With increasing depth the stability of openings driven for ventilation, travel or transport becomes paramount in mine design considerations. As a result the number of roadways and entries, as well as their width must be a minimum. (1) Another important aspect of European mining is the high density of mineable seams, as opposed to the wide lateral extension of a single seam in the U. S. A. Multi-seam mining requires strict planning and near 100% extraction, since with increasing depth, the effect of remnant pillars can be devastating. As a result the face layout of a modern European longwall panel is based on single panel entries of moderate width and great height. The mode of extraction is generally a mixture of the advance and retreat system which is called a 2-system. It is obvious, therefore, that the supports developed for the entries and for the intersection areas are more complex than those in the U. S. A.

Jan 1, 1981

By Harry C. Swanson

TRANSPORTING concrete from mixer to forms has always been a problem. Twenty-five years ago this task was generally accomplished by means of wheelbarrow or concrete buggy. On large dam jobs, as the number of these projects increased, the gantry crane or highline came into use. Today several methods of handling concrete are employed on smaller surface construction jobs, for example, transit-mix trucks or dumpcrete trucks, which have crawler cranes with buckets for placing concrete into forms. In 1944, during early stages of developing Mather mine A shaft, several large underground concrete jobs were necessary. At this time the Cleveland-Cliffs Iron Co. purchased the first pumpcrete machine, introduced by the Chain Belt Co. of Milwaukee. The machine was used to pour approximately 200 cu yd of concrete for a dam, or bulkhead, located 400 ft from the shaft. Concrete was mixed on surface, lowered down the shaft 1000 ft in a 2-cu yd bucket hung under one skip, spouted into the bowl of the pumpcrete machine from the bucket, and pumped directly into the forms.

Jan 4, 1954

By A. F. Baker, E. R. Palowitch, A. W. Deurbrouck

As air-pollution regulations become increasingly more stringent, increased significance is being placed on the amount of sulfur present in coals used for steam generation. These regulations are aimed at minimizing the pollution of the atmosphere with noxious gases such as the sulfur oxides that are formed and emitted when coal is burned. Two meet these future requirements, a definite need exists to reduce the sulfur content of some of the coals used for steam generation. Reducing pyritic sulfur involves liberating the pyrite from the coal and then removing it. The specific gravity of pyrite is high (5.0) compared to that of coal (about 1.2, mineral-free), and standard coal-washing devices, such as wet concentrating tables, will efficiently remove pyrite particles larger than about 100 mesh. Particles below this size will be entrained in the table water and will be carried into the clean coal product. Techniques such as froth flotation are of little benefit for pyrite reduction because the flotation characteristics of pyrite are similar to those of coal.

Jan 6, 1966

By Morris Muskat

THE method of R. W. Moore1 for determining subsurface interfacial depths by means of integrated curves of apparent resistivity has been analyzed theoretically. It is found that the only unique tangents that can be drawn to such curves are the asymptotes at infinite electrode spacing and the tangents through the origin at vanishing electrode spacing. Explicit expressions have been derived for the relationship between the electrode spacing at the points of intersection of these tangents and the thickness of the surface strata as a function of the conductivity parameters for the two-layer and three-layer earths. It is found that in all cases the electrode spacing at the points of intersection will exceed [3/2] of the thickness of the surface layer, and may even become indefinitely large as the resistivity of the deepest layers increases as compared with that of the surface layer. These results do not agree with the empirical findings of Moore that the intersection of the tangent lines fall at an electrode spacing very approximately equal to the thickness "of the surface layer.

Jan 1, 1944

By John C. McDonald

CONTROLLED cold work is used between solution heat treatment and precipitation heat treatment for producing certain tempers of the commercial aluminum base alloy 2219 (designation of the Aluminum Association, U.S.A.) which contains 6.3 pet Cu as the major ingredient responsible for the age hardening. The complete composition limits for this alloy are listed in Table I. The alloy has been described in detail,' and the control of the heat treatment has also been published.2 Beneficial effects of such cold work in other alloys have also been pointed out.3'4 NO data have been published on the effects of varying amounts of cold work under fixed aging conditions. In connection with an investigation of the possibility of providing the desired cold work by explosively generated shock waves, it became desirable to investigate the effect of variable cold work, and to compare the re -sults with those obtained from explosives. The general principles of explosive hardening are well-described in the literature.' All material used was guaranteed by the supplier

Jan 1, 1968

By A. Arrott, G. S. Ansell

A model is proposed to account for the observed strengthening behazlior of ferrous martensites. me model is based upon the inheritance of carbon-rich regions by the martensite which were present in the FERROUS martensite is formed by a nucleation and shear mechanism when austenite is cooled, at a rate which is fast enough to suppress the formation of pearlite, below a critical temperature (Ms ). Although the mechanism of the transformation process appears to be well understood,1,2 the mechanism re- austenite prior to transformation. These carbon-rich regions strengthen the martensite in a manner analogous to the strengthening effect due to a finely dispersed second phase. sponsible for the observed high strengths exhibited by ferrous martensites is uncertain. In this paper, a model is proposed to account for the strengthening of ferrous martensite. MODEL The maximum solubility of carbon in austenite is 1.98 wt pct as compared with a maximum solubility of 0.025 wt pct in ferrite. Prior to transformation, the carbon in the austenite is nonuniformly dis-

Jan 1, 1963

By Howard N. Hall

The compressibility of reservoir rock is a factor which is generally neglected in reservoir engineering calculations. This is due in part to the fact that there is little published information on rock compressibility values for limestones and sandstones. Omission of rock compressibility is undoubtedly justified in calculations for saturated reservoirs; however, in under-saturated reservoirs,* expansion of the rock accompanying decline in the reservoir pressure may be of such magnitude as to affect materially the prediction of reservoir performance. The effect of rock compressibility will be of most importance in: (1) calculation of oil in place by pressure decline data in undersaturated volumetric reservoirs when the limits of the field are unknown or indefinite, and (2) studies of natural water drive performance. To estimate its importance in such cases, a series of laboratory tests were made to obtain usable values for reservoir rock compressibility. The total, or effective, compressibility of any reservoir rock is a result of two separate factors, namely, expansion of the individual rock grains, as the surrounding fluid pressure de-

Jan 1, 1953

By Erwin Zodrow

An elaborate model for the magnetite distribution and genesis in the Smallwood mine, Labrador, based on factor analysis with orthogonal and oblique rotation of the factors, was proposed in an earlier paper. However, it is implicit in that model that variances of one variable shared with all others (communality) are estimated. To avoid the problem of communality estimation in the present investigation, a different type of factor analysis is used which (1) emphasizes the shared variances, and (2) attempts to eliminate, as much as possible, errors associated with the estimation of communality and sampling (unique variance). The samples for the present analysis are not the commonly employed oxide percentage variables, but counts of mineral species in specified areas of thin sections from drill core in the Smallwood mine: quartz, magnetite, calcite, and specular-hematite minerals. The counting procedure for mineral species is similar to modal analysis differing from it principally in the aspect of texture recognition. The constant area in which mineral species are counted is dependent primarily on

Jan 1, 1975

By S. E. Craig

UPON entering the Uranium Field it was a pleasant surprise to find almost absent two factors that have always been a problem to the lead-zinc miner: 1) milling cost per ton, and 2) transportation cost to the milling site. Another interesting condition was the fixed price for the product. Under such conditions it seems rather simple to calculate the economics of a mining venture when grade and tonnage of a uranium ore deposit is known. That is assuming, of course, there is a market for the ore. It has been quite generally assumed by operators that a guaranteed price carried with it a guaranteed market, a subject about which there has been a great deal of discussion in the past several months. The fixed price for uranium in crude ore, calculated to U3O8, varies only slightly in value per pound from rather low grade ore to rather high grade ore. It is by taking advantage of this slight variation in price per pound in certain ranges that miners and shippers may increase substantially the monthly returns from ore shipments.

Jan 7, 1958

By Strathmore R. B. Cooke, Iwao Iwasaki

RECENTLY spectrophotometry has been reported to provide a convenient technique for the rapid and reproducible determination of xanthate concentration in pulp solution 1,2 and for a kinetic study of xanthate decomposition in acid solutions." Since the application of this analytical technique is feasible for those compounds showing pronounced light absorption maxima in the near ultraviolet region, it was deemed advisable to investigate the absorption spectra of some of the organic compounds that are used in flotation. It is known empirically that certain groups of atoms in an organic compound cause characteristic light absorption in the ultraviolet and near ultraviolet range, and the wavelengths and intensities of the corresponding absorption maxima are relatively independent of the nature of the remainder of the compound. The characteristic values of such groups, which are known as chromophores, are given in the literature. 4,5 According to this information, many of the sulphydryl compounds are expected to show absorption maxima in the near or long wavelength ultraviolet region, whereas the saturated fatty acids and the saturated alkylamines do not.

Jan 11, 1957

By N. J. Grant, F. B. Cuff

DURING a recent investigation of high-purity aluminum,' evidence was found for grain-boundary sliding and migration at room temperature. The investigation was concerned primarily with an electron-microscopic study of a fine (approximately 1 micron) network that appeared on the surface of chemically polished aluminum. The nature of the network will not be discussed since it serves only as markers showing relative displacements in this instance. The pertinent observation, shown in Fig. 1, was made on a flat tensile specimen which had been strained about 8 pct at room temperature. As can be seen in this electron micrograph, a grain boundary has undergone a certain amount of sliding. The reason for the existence of the two differently appearing networks is given in the foregoing reference. For present purposes, however, the transition region can be disregarded. A close study of this picture reveals that in addi- tion to sliding there is a narrow band adjacent to and above the grain boundary. Fig. 2 is a schematic drawing showing the essential features of this band.

Jan 1, 1959

By Dean W. Lynch

Arizona: The San Xavier Indian Reservation mine is located approximately 2 ½ miles northwest of Asarco's Mission Mine southwest of Tucson. The company plans to produce oxide and copper-bearing siliceous ore at this operation, construction of which is scheduled for completion in 12 months. Asarco also plans a copper leaching and iron precipitation plant at its mine. The plant will leach 4000 tpd of oxide ore using sulfuric acid produced at the company's acid plant now under construction at Hayden. Copper precipitates will go to the smelter at Hayden. A drilling program at the Sacaton copper prospect in Pinal County, has disclosed two porphyry copper deposits. One deposit, mineable by surface mining, has approximately 17 million tons of material averaging 0.80% Cu. A deeper deposit suitable for under- ground mining has approximately 12 million tons averaging 1.5% Cu. Although Asarco intends to place this property in production, no startup date has been determined.

Jan 1, 1970

By D. E. Ranta, M. W. Ganster, A. D. Ward

An ore zoning technique developed by Climax geologists during the past forty years has been used to contour drill-hole assay values on cross-sections for fourteen porphyry molybdenum deposits in western North America, including the Climax and Henderson orebodies. Detailed geological studies of these large, complex deposits are essential in determining ore controls, which are the factors most critical to the zoning of MoS2 and to conceptualizing geologic model s. The technique provides a detailed representation of the size, shape, grade distribution, and geologic continuity of the individual deposits. It demands a disciplined approach and adheres to rigorous rules while maintaining flexibility for adaptation to widely varying geologic conditions. By defining the limits that guide and control manual, computer-assisted conventional, and geostatistical reserve estimates, it exerts a strong geologic influence on the estimation process. A combination of ore zoning and geostatistical analysis of molybdenum deposits produces a significantly more accurate, precise, and defendable geologic reserve estimate than other methods.

Jan 1, 1984

By P. R. Sperry

In an investigation of the decomposition of the solid solution in a cold worked high-purity aluminum alloy containing 7 pct Mg, aged at temperatures from 30o to 82°C, the nucleating sites at the earliest stages of precipitation were observed to be of two types. Nucleation occurred at the high angle grain boundaries both when the alloy was initially cold worked and when solution annealed. Nucleation also occurred at certain unique deformation markings which began to appear in abundance at approximately 30 pct reduction in thickness by cold rolling. These deformation markings were identified as deformation (kink) bands rather than as the usually assumed "slip planes." Zn material that was cold rolled 15 pct, only the grain boundary Fig. 2—A1-7 pct Mg alloy, cold worked 60 pct and heated at 230° C for 5 min. Etched with Perryman's reagent. X500. Reduced approximately 25 pct for reproduction. (a) Bright field illumination, precipitate deeply pitted. (b) Phase contrast, showing slip markings.

Jan 1, 1962

By Richard C. Timberlake

The disposal of phosphatic clays has presented a problem to the phosphate industry since the mining of phosphate rock first began in Polk County. As the flotation process was introduced in the late 1920's the problem of clay disposal was increased significantly since clay is present in proportionally greater quantities in reserves yielding flotation concentrates. Because of their physical character and the tremendous surface area per unit volume, these clays have the characteristic of retaining large volumes of water as they are slurried during processing. The disposal of clay and the recovery of a portion of the water require settling areas with a capacity ranging up to 2 cu ft for each cubic foot of phosphate matrix mined. According to a recent study by the Bureau of Mines, the average cost for disposal of these wastes is 24.5[c] per ton of product. This is a major cost of phosphate rock production.

Jan 12, 1969

By G. K. Dumbauld, B. E. Morgan

A satisfactory well-cementing composition must retain its fluidity long enough to be pumped into Place; then it must develop within a reasonable length of time sufficient strength and impermeability to anchor the casing in position and to form an effective seal between the casing and the formations. These properties may be evaluated by pumpability, strength (compressive or tensile), and permeability tests. Laboratory test procedures for the determination of pumpability time and strength development have been outlined previously and are readily available,1 but a satisfactory and convenient laboratory procedure for the measurement of the permeability of set cement has not been developed heretofore. some permeability data have been obtained previously by passing air through dried cement specimens.2 such a procedure is unsatisfactory because the drying of set cement alters it physical and chemical properties and subjects it to conditions dissimilar to well conditions. A more realistic method would be one wherein the cement remains water-saturated durin

Jan 1, 1952