Search Documents

By M. L. Holzworth, Joseph C. Kremer, Paul A. Beck, L. J. Demer

FOR alloys which are in practice heat treated to obtain increased strength, such as steels, duralumin, copper-beryllium, and others, the treatment usually involves heating to a relatively high temperature. At such temperatures the grain size of the product is largely determined by grain growth. Even in metals and alloys annealed merely to relieve work hardening, recrystallization is generally followed by a certain amount of grain growth. Thus, effective grain size control, which is often of great practical importance in manufacturing processes, depends on the grain growth behavior of the material used. Despite its importance, grain growth has been the subject of few investigations of a fundamental nature. The term "grain growth" has been used to designate a group of related, but distinctly different, phenomena. The two most important and best known of this group are illustrated by the following example. Curve a in Fig r shows the increase of the average grain size of a copper-beryllium alloy, containing 2 pct Be and 0.15 pct Co, with increasing annealing temperature. The time of annealing was 2 hrs. The grain size was quite uniform in all specimens. The results of a similar experiment with an alloy containing 2 pct Be and 0.31 pct Co are shown by curve b. It is seen that for any annealing temperature below T. the grain size was smaller than in the previous case. Grain growth became slower with the higher Co content. This "inhibiting" effect of the higher Co addition was associated with the appearance in the microstructure of fine, light blue particles of the CoBe phase. Up to temperature T. the structure of the inhibited alloy (curve b) was just as uniform as the structures represented by curve a. However, after annealing at T, or at higher temperatures, the inhibited alloy showed some extremely large grains (much larger than the grain sizes developed by the uninhibited alloy with low Co content) mixed with the small grains according to curve b. The presence of these mixed or "duplex" structures is indicated in Fig 11 by the vertical lines branching off curve b. The type of grain growth occurring in uninhibited Cu-Be alloys (curve a) has has been most frequently and best investigated in brass. This type has been designated as "normal grain growth," while the grain growth phenomena occurring in inhibited materials were, at times, referred to as "abnormal grain growth." However, since the latter term has been applied occasionally to the phenomenon of critical recrystallization, which also results in large grains although by an entirely different mechanism, in the present paper a different nomenclature has been adopted in order to avoid confusion. Typical of the grain growth in uninhibited metals and alloys is the continuous

Jan 1, 1947

By L. J. M. Smits

A theoretical equation is developed describing membrane potentials of shaly sands as a function of the cation-exchange capacity per unit pore volume of the rock and saturating water salinity. This equation is based on the same simple physical model as that employed earlier7 describing the electrical conductivity of shaly sands. Experiments conducted with NaCl solutions showed that the equation is obeyed, except in the case of saturated salt solutions where minor deviations were observed. A possible explanation is given for this discrepancy. As the clay content and the porosity of shales may vary appreciably, shale membrane potentials also vary. It was found that membrane potentials of shales can be calculated accurately with the aid of the same theory. Consequently, changes in membrane potentials can be accounted for by simple measurement of cation-exchange capacities per unit pore volume of both shales and shaly sands. Charts are given to facilitate interpretation of the electrochemical part of the SP in terms of cation-exchange capacities and the salinities of mud filtrate and formation water. INTRODUCTION A spontaneous potential (SP) log is a record of the way in which the electrical potential of a sonde varies as it passes down a borehole. Such variations frequently reflect rock texture, e.g., permeable beds intercalated in an impermeable series often are indicated by a sharp change in potential. Nowadays it is recognized that SP logs may be interpreted in terms of formation-water salinity and formation shaliness. The four sources of the SP are illustrated in Fig. 1. El and E4 represent streaming potentials generated by the flow of mud filtrate through mud cake opposite permeable formations and through shale, respectively. An extensive review of the literature on the evaluation of these streaming potentials is given by Lynchl and will not be discussed here. The remaining part of the SP generally is called the electrochemical potential, which is divided into two parts: a membrane potential across the shale (E3, Fig. 1) and a membrane potential in the permeable sand at the diffusion boundary between formation water and mud filtrate (E2, Fig. 1). It was found by wyllie2 that the membrane potential across the shale, E3, is the most important contribution to the electrochemical potential, the shale acting as a semi permeable membrane. When the sand is clean it does not influence the diffusion process, so E2 equals the value of the so-called liquid-liquid junction potential observed when the two solutions diffuse freely into each other. When the sand contains clay, however, this interferes with the diffusion process and affects the diffusion potential generated. The greater the proportion of clay, the stronger this effect will be. Wyllie,3 Doll4 and Poupon et al.5 took this effect into account theoretically, starting from a physical

Jan 1, 1969

By R. I. Jaffee, J. G. Dunleavy, H. R. Ogden, Webster Hodge

INTRODUCTION EARLY in 1946, at the instigation of the U. S. Army Signal Corps, the authors made an extensive survey of the available literature covering high-strength, high-conductivity alloys. For the purposes of the Signal Corps, the minimum tensile strength to be considered was 150,000 psi, together with at least 50 pct IACS conductivity. No single alloy was found to be in production, or mentioned in the literature, which had this combination of properties. The constitution diagram for the iron-copper alloys is not well established in the respect to the two-liquid region. Fig I, taken from the 1939 Ed. of the ASM Metals Handbook, shows a two-liquid system existing above the liquidus temperature, but disconnected from it. Although Ruer and Fick1 and Ruer and Goerens2 definitely established the fact that two liquid layers could occur in the system, Ruer3 was not convinced that the line off immiscibility was closed in the center. Maddocks and Claussen4 found no liquid immiscibility at temperatures up to 1570°C in alloys containing almost no carbon. Although the diagram would indicate age hardening of the copper-iron alloys is possible, Hanson and Fords found that little hardening effect could be obtained. However, Gordon and Cohen6 reported that the response is better if the quenching is very efficient. Although iron has a potent effect on the conductivity of copper, Hanson and Ford5 have shown that, when hot-rolled copper iron alloys are aged at 1200°F, the electrical conductivity decreases sharply with iron contents up to 0.2 pct Fe, and then levels off at conductivities between 60 to 70 pct IACS with compositions to 2.1 pct Fe. They also found that aging did not increase the tensile strength, although increasing iron content gave a moderate improvement in strength. High-strength copper-iron alloys, usually containing about 60 pct iron, had been reported by Smith and Palmer.7 They found that an alloy containing 56.4 pct copper, 0.21 pct magnesium, balance iron, would give a maximum tensile strength of 170,000 psi and an electrical conductivity of slightly over 35 pct IACS. The alloy could also be processed to have 150,000 psi tensile strength, and about 41 pct IACS conductivity. Decreasing the iron content increased the electrical conductivity, but the long mushy range during freezing of the alloy containing 10 to 20 pct iron made the production of good castings difficult, In spite of the difficulty encountered by Smith and Palmer with alloys of around 20 pct iron, it was decided to make a rather complete investigation 0f this type of alloy. As a result 0f this investigation, a method of alloying and fabricating copper alloys containing 10 to 15 pct iron was developed

Jan 1, 1948

By K. A. Gschneidner, O. D. McMasters

DgIel-ential thermal, nretallographic, and X-ray paramzetric methods were used to establish the Yb-Pb phase dingram. The terminal solid solubilities in the system are less than 0.2 at. pct. Lead additions lower the 792°C transformation tewzperature of pure ytterbiun~ at 787°C by means of an inverted peritectic veaction. Ytterbium additions raise the 327oC melting point of lead to 329°C by means of a perilectic reaction. Three intermetallic compounds Yb2Pb, YbPb, and YbPb, melt congruerttly at 1246", 1116o, and 740°C. respectively. YbsPb3 forms by a peritectic reacliorz at 1250°C. YbzPb crystallizes in the PbCh (C23) type structure and the orthorhombic latliceo constants are a, = 7.478. bo = 5.225, aud C0 = 9.549A. YbsPbs crystallizes in the hfnsSi3 (D8a) type structure. The hexa~nal lattice constants for this phase are a, = 9.325 and co = 6.92d. YbPbl crystallizes in the cubic AuCU3 (Ll2) type structure with a: = 4.8628 + 0.0008A. YbPb is diwrorphic with the structure change occurring al 507°C upon healing. The crystal structures of the two forttzs were not determined. Eulectic reactions occur at 5.1 at. pct Pb and 769oC, 41.5 at. pct Pb and 1086oC, and G8.0 at. pct Ph and 717°C: RELIABLE information concerning the alloying behavior of most of the rare-earth metals is scarce. A systematic study of the rare earth-lead alloy systems now in progress is an effort to supply such information. Determination of the phase diagram of the Yb-Pb alloys is the first step of this study. Variations in the valence of normally divalent ytterbium may be studied by comparing the characteristics of the Yb-Pb alloys to those of the trivalent rare earth-lead and of the divalent alkaline-earth-lead systems. Of particular interest are the melting temperatures of the intermetal-lic compounds since these are known to be high relative to the melting points of the constituent metals. Crys-tallographic and magnetic susceptibility data for the rare earth-lead alloys are to be included in the comparative study. Results from this and subsequent investigations should provide a better understanding of alloy formation. EXPERIMENTAL PROCEDURE Materials. The major impurities in the ytterbium and lead used in this investigation are listed in Table I. The lead was obtained from Cominco Products, Inc., and was specified to be 99.99 pct pure. The ytterbium was prepared in this laboratory by the lanthanum reduction of the oxide followed by a distillation of the ytterbium. Alloy Preparation. The alloys were prepared by

Jan 1, 1968

By I. J. Demer, M. L. Holzworth, J. C. Kremer, P. A. Beck

For alloys which are in practice heat treated to obtain increased strength, such as steels, duralumin, copper-beryllium, and others, the treatment usually involves heating to a relatively high temperature. At such temperatures the grain size of the product is largely determined by grain growth. Even in metals and alloys annealed merely to relieve work hardening, recrystal-lization is generally followed by a certain amount of grain growth. Thus, effective grain size control, which is often of great practical importance in manufacturing processes, depends on the grain growth behavior of the material used. Despite its importance, grain growth has been the subject of few investigations of a fundamental nature. The term "grain growth" has been used to designate a group of related, but distinctly different, phenomena. The two most important and best known of this group are illustrated by the following example. Curve a in Fig I shows the increase of the average grain size of a copper-beryllium alloy, containing 2 pct Be and 0.15 pct Co, with increasing annealing temperature. The time of annealing was 2 hr. The grain size was quite uniform in all specimens. The results of a similar experiment with an alloy containing 2 pct Be and 0.31 pct Co are shown by curve b It is seen that for any annealing temperature below T, the grain size was smaller than. in the previous case. Grain growth became slower with the higher Co content. This "inhibiting" effect of the higher Co addition was associated with the appearance in the microstructure of fine, light blue particles of the CoBe phase. Up to temperature T, the structure of the inhibited alloy (curve b) was just as uniform as the structures represented by curve a. However, after annealing at T or at higher temperatures, the inhibited alloy showed some extremely large grains (much larger than the grain sizes developed by the uninhibited alloy with low Co content) mixed with the small grains according to curve b. The presence of these mixed or "duplex" structures is indicated in Fig I by the vertical lines branching off curve b. The type of grain growth occurring in uninhibited Cu-Be alloys (curve a) has been most frequently and best investigated in brass. This type has been designated as "normal grain growth,'' while the grain growth phenomena occurring in inhibited materials were, at times, referred to as "abnormal grain growth." However, since the latter term has been applied occasionally to the phenomenon of critical recrystallization, which also results in large grains although by an entirely different mechanism, in the present paper a different nomenclature has been adopted in order to avoid confusion. Typical of the grain growth in uninhibited metals and alloys is the continuous

Jan 1, 1949

By E. J. Duggan

THE mine and mill of the Climax Molybdenum Co. are at Climax, Colorado. Climax is on Fremont pass directly on the Continental Divide, at an elevation of 11,400 feet. DESCRIPTION OF ORE The Climax ore-bearing rock is essentially an altered and highly silicified granite, fully half of the gangue being quartz. Molybdenite is the only mineral of economic consequence and most of it is intimately associated with quartz in the form of fine veinlets and stringers. Other minerals are molybdite, pyrite, and chalcopyrite. While the molybdite may be readily extracted by hydrometallurgical methods, its content is too low to make such operations profitable. The pyrite content ranges from 2 to 5 per cent and that of the chalcopyrite from 0.03 to 0.05 per cent. There is not enough copper to make its recovery attractive and one of the metallurgical problems is the elimination of it and the pyrite from the product. On account of the dose association of the molybdenite with the quartz and the necessity of eliminating the pyrite and chalcopyrite from the final product, fine grinding followed by flotation is the only feasible method of concentration. HISTORY Construction of the first milling unit was started in 1917 and it was operated during parts of 1918 and 1919. In the postwar years, there was almost no demand for the product and production was at a standstill until 1924. The Company's research campaign to develop the use of the metal began to show results in that year. From 1926 to 1932 production ranged from 500 to 1200 tons per day. In 1931 an additional mill section was built and production was gradually increased until in 1934 and' 1935 about 3000 to 4000 tons was milled per day. This tonnage overtaxed the milling facilities, and as the demand for molybdenum was growing constantly, additional milling equipment was needed. In 1936 and 1937 another crushing plant, six additional mill sections and the necessary auxiliary plants were constructed and brought into operation. This plant was designed to mill 10,000 tons per day, but it was not long before 12,500 tons was being treated during periods of peak demands. During the summer of 1941, to meet defense needs, the mill has been required to treat 15,500 tons per day. This has been accomplished with little plant expansion and at no loss in recovery, as will be described later. To increase capacity still further, one more primary section is now being built. This will bring capacity to 18,000 tons per day, which can be stretched to 20,000 tons at a small sacrifice in recovery. CRUSHING There are two crushing plants: No. I, of 5000 tons capacity (flowsheet in Fig. 1) and No. 2, of 15,000 tons capacity (Fig. 2).

Jan 1, 1942

By H. B. Aaron

DIFFRACTION micrography provides a useful tool for studying complex strain fields. Newkirk1 observed an X-ray diffraction effect due to strain interactions at the intersection of slip lines in LiF and attributed this effect to a reduction of primary extinction due to strain-gradients. It is the object of the current study to correlate the observations and rationalize the appearance of the strain fields around intersecting slip planes in x-ray extinction contrast studies by a semiempirical method. Fig. 1 shows typical strain patterns observed by Newkirk on (200) reflections in LiF using chromium radiation and a variation of the Berg-Barrett (B-B) technique. In other reflections (e.g., {220}) the strain patterns are absent. If one defines a vector 3 along the striations from the more to the less dense portion, and a vector v in the direction of the X-ray beam parallel to the reflecting plane, such that both 3 and v lie in the reflecting plane of the crystal, Fig. 1, then the positions of the striations on (200) reflections appear to be confined such that where is the angle between v and 3, Fig. 1. It will be seen later that 3 is the projection of Sb on the reflecting planes. In some instances the strain effects are observed only above the slip plane, Fig. l(C), in others only below, Fig. l(D). Where the strains appear to be both above and below the slip line, Fig. l(E), one sees that there are actually two slip lines present, Fig. 1(F) and (G). Furthermore, the strain patterns are observed in the vicinity of the intersection of emergent edge dislocations (diagonal lines on the micrograph) with emergent screw dislocations (horizontal lines on the micrograph), e.g., Fig. l(HJ) and (MN), but not in the vicinity of the intersection of two emergent edge dislocation arrays, Fig. l(HJ) and (KL). However, in the latter case the contrast of the dislocation array itself is reduced along (KL) and increased along (HJ). Line (AB) in Fig. 1 is the edge of the crystal, and the material to the left of (AB) is the side of the sample. Any empirical correlation will have to include most, if not all of the aforementioned observations. Lang2 and Newkirk1 determined that the condition for contrast is given by g-b#0 [2] where b is the Burgers' vector and g the diffraction vector (normal to the reflecting planes). If one assumes that the direction of the observed strain fields is given by the vector sum of the slip vectors (Sb1) of the intersecting slip planes, then Eq. [2] may be generalized to g-S#0 [3]

Jan 1, 1963

By Konrad Stern

The terms asphalt and bitumen have been applied interchangeably, although incorrectly on occasion, for centuries to various bituminous materials that were found in nature. Native bituminous materials of only the solid types, deposits of which are found on or near the surface of the ground, together with the principal asphaltic type petroleum bitumens will be considered in this chapter. The international dictionary compiled by the "Permanent International Association of Road Congresses" still gives the full name as "Asphaltic Bitumen" but of recent years the word "Bitumen" has been recognized as most appropriate and is defined by the American Society for Testing Materials as follows: "Mixtures of hydrocarbons of natural or pyrogenous origin, or combinations of both, frequently accompanied by their nonmetallic derivatives, which may be gaseous, liquid, semisolid or solid and which are completely soluble in carbon disulfide." Asphaltic pyrobitumens, as defined by Abraham,2 is a species of pyrobitumen, including dark-colored, comparatively hard and nonvolatile solids; composed of hydrocarbons, substantially free from oxygenated bodies; sometimes associated with mineral matter, the nonmineral constituents being infusible and largely insoluble in carbon disulfide. Deposits of native bituminous materials are found scattered over the entire world, but many are relatively unimportant as far as commerce is concerned. No attempt has been made to cover all of the known deposits. The principal bituminous materials of commercial interest are: 1. Native asphalts, solid or semisolid, associated with mineral matter such as Trinidad Lake asphalt, Rock asphalt and Selenitza, Boeton and Iraq asphalts. 2. Native Asphaltites, such as gilsonite, grahamite and glance pitch, conspicuous by their hardness, brittleness and comparatively high softening point. 3. Asphaltic bitumens obtained from nonasphaltic, semi-asphaltic and asphaltic crude petroleum by distillation, blowing with air and the cracking of residual oils. 4. Asphaltic pyrobitumens of which wurtzilite and elaterite are of chief interest industrially as they depolymerize upon heating, becoming fusible and soluble in contrast to their original properties in these respects.2 5. Mineral waxes, such as ozokerite, characterized by their high crystallizable paraffine content. Native Lake Asphalt At Brighton situated in the southwestern part of the Island of Trinidad is one of the largest deposits of native asphalt in the world.3 The lake is oval in shape, covering an area of 114 acres and having a depth of 285 ft at its center. The material forming this deposit is an emulsion of water and bitumen with a suspension of mineral matter consisting of impalpably fine clay dispersed by nature in the asphalt, and small quantities of silica and vegetable matter. The entire mass of asphalt is in slow but constant motion as evidenced by the migration of islands of vegetation from one place to an-

Jan 1, 1960

By Marston G. Fleming

CRITICAL pH has been defined by Wark1 as that pH value below which a mineral will float and above which it will not float in solutions containing a given concentration of collector but free from other depressants or activators. - The relationship between mineral, collector concentration, and pH is expressed in the form of a critical pH curve determined by the captive bubble method and is generally regarded as being fundamental to the system involved. The mechanism of alkali depression is currently in dispute, two general theories having received authoritative support. The view expressed in Taggart's chemical theory of flotation2 is that in the presence of a critical concentration of hydroxyl ions, all the metal ions available at the surface of the mineral are present as anions of the form [M (OH)x]-y. The formation of the necessary metal xanthate is thus precluded and, furthermore, any metal xanthate coating previously formed, at a lower pH, will be dissolved. Gaudin3,4 and the Melbourne school under Ware hold that alkali depression is caused by the preferential adsorption of hydroxyl ions by the mineral surfaces. This paper describes an investigation of the mechanism of alkali depression in each of the three systems: cerussite-aqueous carbonate-xanthate, cerussite-xanthate, and galena-xanthate. Alkali Depression of Cerussite by Control of Carbonate Ion Concentration Wark and Cox6 have shown that in the presence of Na2CO3 a higher concentration of xanthate is required to effect bubble contact with a cerussite surface than in carbonate-free solutions. To examine this depression of cerussite by sodium carbonate, a series of captive bubble tests was carried out on cerussite specimens in solutions containing 100 mg per liter of potassium ethyl xanthate and varying concentrations of sodium carbonate. The pH was adjusted by the addition of dilute hydrochloric acid. For purposes of comparison a standard critical pH curve was determined for cerussite with potassium ethyl xanthate in solutions containing no added carbonate. In the latter case pH adjustment was made with sodium hydroxide. The experimental method employed in both series was broadly similar to that described by Wark and Cox;7-9 a number of refinements suggested by Sutherland10 were adopted, and the procedure was further developed and modified to suit the particular requirements of the investigation. The relationship between pH and the concentration of potassium ethyl xanthate necessary to induce bubble contact at cerussite surfaces is shown in Fig. 1. The relationship between pH and the concentra- [ ] tion of sodium carbonate necessary to prevent bubble contact at cerussite surfaces in the presence of 100 mg per liter of potassium ethyl xanthate is shown in Fig. 2. Comparison of the. two curves shows that at a collector concentration of 100 mg

Jan 1, 1952

By J. B. Bassett, E. S. Rowland

The experimental work reported herein firas inspired by the publication of a paper by Grange and stewart, in which it was suggested that at low chromium contents the effect of this element on the Ma point was greater than at higher chromium contents, It was argued that, if a small increase of chromium in solution in austenite caused a sharp lowering of the M, point, it might lead to an explanation of occasional unsolved stress cracking of SAE 52100 during heat treatment. Commercial hardening is carried out at temperatures of incomplete solution, leaving carbides available to enrich the austenite during any inadvertent increase in temperature, such enrichment of the austenite in chromium content would lower the M, point nearer room temperature where cracking is more likely to occur. According, it was decided to investigate the effect of chromium, in quantities between o and 2 pet, on the M, point of commercial steels. Fig I summarizes the data available on chromium steels. For purposes of comparison, the M, temperature values were corrected by means of the Grange and Stewart formulas to (I) Hypoeutectoid compositions: 0.50 pct carbon and 0.80 pct manganese (z) Hsereutectoid compos-sition': 1." pet carbon and O.35 pct manganese. Only the steels having compositions reasonably close to these corrected values were included, because large adjustments inevitably introduce increased error such as are experienced in using the formula. The straight lines of Fig I were drawn by the authors. These data obviously do not settle the question Of the effect Of chromium On the Md Oint, particularly at low chromium contents. While it is fairly well established that chromium causes the M, to be lowered when present in quantities of I pet Or more, Grange and Stewart1 have suggested that in small amounts (less than 1 pet) it is more effective in lowering the Ma point, while Klier and Troiano2 have suggested that in small amounts it is less effective in lowering the Ma point. Payson and Savage3 concur with Klier and Troiano and further suggest that the effect is not linear at these concentrations. Rose and Fischer4 report that small amounts of chromium actually raise the Ma point of a 0.20 carbon steel. Material Two series of 35 Ib induction heats were melted for this work, the analyses of which are given in Table I. One series was aimed at 0.50 pct carbon and 0.80 pct manganese with chromium additions in 0,25 pet increments from o to 1.5 pct with a single heat at 2.0 pct Cr. This series was considered necessary because the commercial heat treatment of SAE 52100 does not generally introduce more than about 0.60 pct carbon in solution in the austenite. The high

Jan 1, 1949

By E. J. Duggan

THE mine and mill of the Climax Molybdenum Co. are at Climax, Colorado. Climax is on Fremont pass directly on the Continental Divide, at an elevation of 11,400 feet. DESCRIPTION OF ORE The Climax ore-bearing rock is essentially an altered and highly silicified granite, fully half of the gangue being quartz. Molybdenite is the only mineral of economic consequence and most of it is intimately associated with quartz in the form of fine veinlets and stringers. Other minerals are molybdite, pyrite, and chalcopyrite. While the molybdite may be readily extracted by hydrometallurgical methods, its content is too low to make such operations profitable. The pyrite content ranges from 2 to 5 per cent and that of the chalcopyrite from 0.03 to 0.05 per cent. There is not enough copper to make its recovery attractive and one of the metallurgical problems is the elimination of it and the pyrite from the product. On account of the close association of the molybdenite with the quartz and the necessity of eliminating the pyrite and chalcopyrite from the final product, fine grinding followed by flotation is the only feasible method of concentration. HISTORY Construction of the first milling unit was started in 1017 and it was operated during parts of 1918 and 1910. In the postwar years, there was almost no demand for the product and production was at a standstill until 1024. The Company's research campaign to develop the use of the metal began to show results in that year. From 1926 to 1932 production ranged from 500 to 1200 tons per day. In 1931 an additional mill section was built and production was gradually increased until in 1934 and 1935 about 3000 to 4000 tons was milled per day. This tonnage overtaxed the milling facilities, and as the demand for molybdenum was growing constantly, additional milling equipment was needed. In 1936 and 1937 another crushing plant, six additional mill sections and the necessary auxiliary plants were constructed and brought into operation. This plant was designed to mill I0,000 tons per day, but it was not long before 12,500 tons was being treated during periods of peak demands. During the summer of 1941, to meet defense needs, the mill has been required to treat 15,500 tons per day. This has been accomplished with little plant expansion and at no loss in recovery, as will be described later. To increase capacity still further, one more primary section is now being built. This will bring capacity to 18,000 tons per day, which can be stretched to 20,000 tons at a small sacrifice in recovery. CRUSHING There are two crushing plants: No. I, of 5000 tons capacity (flowsheet in Fig. I) and No. 2, of 15,000 tons capacity (Fig. 2).

Jan 1, 1942

By H. C. Fiedler

The solubility of sulfur in Si-Fe was determined by the metallographic examination of heat-treated and quenched samples. In the absence of manganese, the solubility in 3.1 pct Si-Fe was found to be about 0.010 pct at 1000o C, 0.015 pct at 11000C, and 0.020 pct at 1150°C, which is substatntially less than hitherto reported. Increasing the silicon content was found to decrease the solubility of sulfur, which is consistent with the increase in the activity coefficient of sulfur with increasing silicon content that has been reported for Fe-Si alloys. Manganese additions were studied in alloys containing 3.1 pct Si and between 0.013 and 0.015 pct S. At low manganese levels the solubility product of manganese sulfide was found to be lower than previously reported. THE solubility of sulfur in pure polycrystalline iron has been reported by Rosenquist and Dunicz1 and by Turkdogan et al.2 Samples were equilibrated in atmospheres containing different ratios of H2S/H2. Both groups of investigators found a solubility limit in y iron of 0.013 pct at 1000oC and 0.031 pct at 1200°C. In addition, Rosenquist and Dunicz1 found a solubility limit in a iron of 0.020 pct at 900°C. Ainslie, Hoffman, and seybolt3 found significantly higher sulfur contents in polycrystalline iron samples than in single-crystal samples after heating at 890°C in a sealed tube containing a mixture of powdered iron and FeS made with s35. Whereas the single crystals contained 0.013 and 0.016 pct S (± 0.005 pct), the polycrystalline samples contained between 0.016 and 0.026 pct S. Autoradiographs suggested that the excess sulfur in the polycrystalline samples was due to the segregation of sulfur in solution at grain boundaries. Ainslie and seybolt4 have reported on the solubility of sulfur in 3 pct Si-Fe. Their samples were sealed in capsules containing hydrogen and sufficient sulfur as cobalt sulfide to saturate the sample. After heat treating, the sulfur-rich phase on the surface was removed by abrading, and the sulfur content of the sample was taken as the equilibrium value for that temperature. Before the equilibrating heat treatment, the samples were heated to 1300°C to coarsen the grains. The resulting grain size, which was about 3/18 in. in diam, was considered sufficiently large to preclude a sensible increase in sulfur solubility due to grain boundary segregation. They reported the solubility to be 0.029 pct at 900oC, 0.063 pct at 1000oC, 0.076 pct at 1100°C, 0.122 pct at 1200°C, and 0.098 pct at 1300°C.

Jan 1, 1968

Smoky Valley Mining Company, Round Mountain, Nevada, was the pioneer operation designed for large scale heap leaching of crushed gold ores. It is located in the Big Smoky Valley which stretches 160 km (100 miles) through central Nevada west of the Toiyabe Mountain Range. Gold was first-discovered at Round Mountain, 88 km (55 miles) north of Tonopah, in 1905; and mining in the area included placer operations, which ran from 1946 to about 1960. Smoky Valley Mining Company is a partnership of Felmont Oil Co., Case-Pomeroy & Co., and Copper Range Co., with the latter being wholly owned by Louisiana Land and Exploration Co. In 1969, an option on the Round Mountain property was acquired by Copper Range, and during 1974 a decision was reached to proceed with mine development and plant construction. Ore reserves were reported at 10,537,000 mt (1 1,617,000 st) of 2.09 g per mt (0. 061 oz per ton) gold using a cut- off grade of 0.69 g (0.02 oz). Silver content was approximately 2.4 g per mt (0.07 oz per ton) and the waste to ore ratio was about 1: 1. By the end of 1976 heap leaching was in operation. The ore is a rhyolite tuff, sometimes described as a gold porphyry with highly abrasive qualities but which does not break down into slimes upon contact .with cyanide solutions. Gold is unevenly distributed through the ore but as a whole it is in a very finely divided state. Climatic conditions are extreme in central Nevada. Summers are hot and dry while winters are windy and cold with subfreezing temperatures. Elevation of the property is about 1,920 m (6,300 ft). Precipitation averages 203 mm (8 in.) per year. Until February of 1980, leaching was continued until the temperature reached minus 2ºC (28º F), and about 10 months leaching was the average. Water for the operation is drawn from the Toiyabe Mountains through a 13. 7 km (8. 5 mile) pipeline, originally installed in 1915, or from wells in the valley bottom. The plant requires make-up water at the rate of about 1,500 liters per min (400 gpm). On a schedule of three shifts, seven days per week, the daily output at Round Mountain amounts ,to 12, 700 mt (14, 000 st) consisting of 6,350 mt (7,000 st) each of ore and waste. Ore is hauled with a fleet of 45 mt (50 st) trucks and dumped into the 1,0.70 by 1,650 mm (42 by 65 in. ) gyratory primary crusher located near the pit. The primary

Jan 1, 1981

By Walter Crafts, C. M. Offenhauer

In a previous study of the carbide phase of chromium steels, it was shown that chromium carbide (Cr7C3) is 2 more stable carbide than cementite (Fe3C) at tempering temperatures above about 500°C. in quenched steels containing from about I to 7.5 per cent chromium. Below this temperature the carbide phase was found to consist of cementite in all of the steels examined. In the present investigation it was found that a similar change in the carbide phase takes place in molybdenum and in chromium-molybdenum steels at approximately the same tempering temperatures. The approximate ranges of occurrence of the alloy carbides Cr7C3, Cr4C, and Mo2C have been determined in steels containing up to 5 per cent chromium, I per cent molybdenum and 0.60 per cent carbon. The experimental steels were made in small high-frequency furnaces from Armco ingot iron, low-carbon ferrochromium and calcium molybdate and were poured into 2-in. ingots, which were forged to I-in. round bars. Sections of the bars were heated to the carbide-solution temperature and cooled rapidly to induce austenite transformation at relatively low temperatures. The steels were subject to some segregation, therefore comparatively high temperatures were necessary to dissolve all of the carbides. The microstructure of the quenched specimens was examined to verify the belief that the carbides had been dissolved, and also to determine the nature of the nonmartensitic structure of incompletely hardened steels. Ferrite and pseudo-martensite were present in some of the specimens, but all specimens were quenched at such a rate that pearlite was not formed, in order to ensure the formation of the carbides at temperatures lower than about 500°C. It had been found previously1 that in chromium steels the chromium carbide could be produced by transformation of austenite in the pearlite range above 500°C., and, in order to start the tempering treatment with the carbide present as cementite, the absence of pearlite was considered to be essential. The specimens were tempered for 64 hr. to permit the formation of the stable carbide. After tempering, the specimens were submitted to microscopic and X-ray examination. The carbides were separated either electrolytically in a 5 per cent HCl electrolyte or with an acidified copper-potassium chloride solution. The crystal structure of the carbide phases was determined by the Debye-Scherrer type of X-ray patterns. The X-ray patterns obtained from specimens near the boundaries between two types of carbides were generally weak and diffuse as compared with the other patterns. For this reason, and because the more soluble components may be masked, the boundaries between the phases could not be determined precisely. However, the X-ray analysis of electrolytically separated carbides has given consistently reproducible results

Jan 1, 1943

By Walter Crafts, C. M. Offenhauer

In a previous study of the carbide phase of chromium steels, it was shown that chromium carbide (Cr7C3) is 2 more stable carbide than cementite (Fe3C) at tempering temperatures above about 500°C. in quenched steels containing from about I to 7.5 per cent chromium. Below this temperature the carbide phase was found to consist of cementite in all of the steels examined. In the present investigation it was found that a similar change in the carbide phase takes place in molybdenum and in chromium-molybdenum steels at approximately the same tempering temperatures. The approximate ranges of occurrence of the alloy carbides Cr7C3, Cr4C, and Mo2C have been determined in steels containing up to 5 per cent chromium, I per cent molybdenum and 0.60 per cent carbon. The experimental steels were made in small high-frequency furnaces from Armco ingot iron, low-carbon ferrochromium and calcium molybdate and were poured into 2-in. ingots, which were forged to I-in. round bars. Sections of the bars were heated to the carbide-solution temperature and cooled rapidly to induce austenite transformation at relatively low temperatures. The steels were subject to some segregation, therefore comparatively high temperatures were necessary to dissolve all of the carbides. The microstructure of the quenched specimens was examined to verify the belief that the carbides had been dissolved, and also to determine the nature of the nonmartensitic structure of incompletely hardened steels. Ferrite and pseudo-martensite were present in some of the specimens, but all specimens were quenched at such a rate that pearlite was not formed, in order to ensure the formation of the carbides at temperatures lower than about 500°C. It had been found previously1 that in chromium steels the chromium carbide could be produced by transformation of austenite in the pearlite range above 500°C., and, in order to start the tempering treatment with the carbide present as cementite, the absence of pearlite was considered to be essential. The specimens were tempered for 64 hr. to permit the formation of the stable carbide. After tempering, the specimens were submitted to microscopic and X-ray examination. The carbides were separated either electrolytically in a 5 per cent HCl electrolyte or with an acidified copper-potassium chloride solution. The crystal structure of the carbide phases was determined by the Debye-Scherrer type of X-ray patterns. The X-ray patterns obtained from specimens near the boundaries between two types of carbides were generally weak and diffuse as compared with the other patterns. For this reason, and because the more soluble components may be masked, the boundaries between the phases could not be determined precisely. However, the X-ray analysis of electrolytically separated carbides has given consistently reproducible results

Jan 1, 1943

By R. C. Buehl, M. B. Royer

High manganese slags of low phosphorus and iron content are produced by air oxidation of high phosphorus spiegeleisen in a basic-lined converter. Control of phosphorus and iron within specification limits for ferromanganese ore feed is obtained by a unique cyclic operating procedure. Various types of slags, or synthetic manganese ore, can be made. AN affiliated paper' describes the production of high phosphorus spiegeleisen containing 14 to 23 pct Mn and up to 4 pct P in an experimental blast furnace from open-hearth slag or manganiferous iron ore. This phosphorus content is too high for use of the spiegel in normal steel-production operations. Consequently, a preferential separation must be effected whereby the manganese is concentrated in a product that is usable in industrial operations. The preferential separation methods being investigated for this phase of the work are confined to pyrometal-lurgical processes for ready incorporation into steel-plant operations. It is fortunate that manganese is more actively oxidizable than iron or phosphorus, and therein lies a preferential separation method for isolating manganese from these two elements. Silicon is more strongly oxidizable than manganese, and its oxidation precedes, or occurs simultaneously, with manganese. Therefore, manganese and silicon are separable into a high manganese oxide slag phase while the phosphorus and iron remain in the molten metallic state. Complete separation of these elements represents an ideal condition which is not generally attainable in actual operations. This pyro-metallurgical method for separating manganese from phosphorus and iron by preferential oxidation was investigated by blowing 500 lb of metal in a basic-lined vessel to obtain preliminary information on the effectiveness of the procedure. Certain conditions of attainment in the separation process are desirable in any method for removing manganese from high phosphorus spiegeleisen, such as: 1—High recovery of manganese in the oxidation product; 2—the product to be of equal or better quality than ferromanganese-grade ore—48 pct Mn minimum, less than 10 pct SiO2, and Mn-P ratio of 300:1; and 3—attainment of the enumerated objectives in a product amenable to industrial handling, such as a slag of high manganese content that will flow from the processing vessel and of sufficient fluidity for ready separation of metallic granules that may have become mixed with the manganese slag phase. Previous Work Recovery of manganese from low grade ores and industrial byproduct slags by smelting to spiegeleisen, with subsequent oxidation to synthetic ferro-manganese-feed ores, has been a subject for periodic investigation during the past four or five decades in the United States and Germany. Joseph' and associates of the Bureau of Mines North Central Experiment Station, Minneapolis, Minn., smelted manganiferous iron ores of the Cuyuna range, Minn., to spiegeleisen and subsequently tried air and ore oxidation procedures for concentrating the manganese into synthetic ferrograde manganese ore. Joseph's results on the operation of a side-blown basic-lined converter for air oxidation of manganese from molten spiegeleisen were so discouraging that the procedure was abandoned after 11 blowing tests. Much slag was thrown from the converter vessel; phosphorus content was four to five times the maximum allowable for ferro ore; and a manganese-iron ratio of only 2 or 3:1 was obtained in the slag instead of the required 8:1. Oxidation of manganese from spiegeleisen with about 0.5 pct P, by adding iron ore to molten spiegel in an experimental open-hearth furnace, proved moderately successful in Joseph's experiments. The main drawback to the operation was the necessity for over-oreing for effective oxidation of the manganese with consequent too high iron oxide residual in the slag. Furthermore, the phosphorus content was proportional to the iron concentration and therefore much too high, so that several hours of reduction by a carbonaceous material were required to adjust the iron and phosphorus to the desired content of high grade ferro feed. A troublesome feature of the slag product of the spiegel oxidation process was its lack of fluidity if the silica content was less than 10 pct, the concentration considered desirable for the synthetic ore. Approximately twice the desired concentration of silica was required to impart enough fluidity for transfer from the vessel by pouring. The acute shortage of manganese in Germany

Jan 1, 1953

By E. H. Dix, F. Keller

The use of magnesium as an alloying element in aluminum alloys has been limited, in general, to comparatively small quantities. In duralumin-type, strong aluminum alloys, magnesium is present to the extent of 35 to 3/4 per cent. and various grades of Magnalite and the "Y" alloy of the National Physical Laboratory of England contain up to 1 1/2 per cent. In this country small quantities of aluminum alloy sheet containing 4 per cent. magnesium are produced commercially. All commercial aluminum contains sufficient silicon to convert a portion of the magnesium added to the compound Mg2Si. It is well known that the solubility of both magnesium and magnesium-silicide decrease with decrease in temperature. It is, therefore, impossible to separate the age-hardening effect of the magnesium-silicide from that of magnesium, except by the use of aluminum of such high purity that the silicon content is negligible. The present paper is the fifth l, 2, 3, 4 of a series from the laboratories of the Aluminum Co. of America reporting the results of investigations of the equilibrium relations in aluminum-rich alloys made from the high-purity aluminum manufactured by this company. 5 Previous Investigations A number of investigations have been made of the constitution of the complete aluminum-magnesium system and several determinations made

Jan 1, 1929

By F. Keller, E. H. Dix

The use of magnesium as an alloying element in aluminum alloys has been limited, in general, to comparatively small quantities. In duralumin-type, strong aluminum alloys, magnesium is present to the extent of 35 to 3/4 per cent. and various grades of Magnalite and the "Y" alloy of the National Physical Laboratory of England contain up to 1 1/2 per cent. In this country small quantities of aluminum alloy sheet containing 4 per cent. magnesium are produced commercially. All commercial aluminum contains sufficient silicon to convert a portion of the magnesium added to the compound Mg2Si. It is well known that the solubility of both magnesium and magnesium-silicide decrease with decrease in temperature. It is, therefore, impossible to separate the age-hardening effect of the magnesium-silicide from that of magnesium, except by the use of aluminum of such high purity that the silicon content is negligible. The present paper is the fifth l, 2, 3, 4 of a series from the laboratories of the Aluminum Co. of America reporting the results of investigations of the equilibrium relations in aluminum-rich alloys made from the high-purity aluminum manufactured by this company. 5 Previous Investigations A number of investigations have been made of the constitution of the complete aluminum-magnesium system and several determinations made

Jan 1, 1929

By M. F. Goudge

Production of many industrial minerals reached all-time records in 1965. In keeping with the high level of industrial activity throughout the nation, producers of many industrial minerals operated at capacity or near capacity, notably the producers of phosphate, potash and sulfur. In the case of sulfur, the demand exceeded production and orders were filled, in part, from stocks accumulated in previous years. Industrial minerals as a group continued to increase both in value and quantity at a faster percentage rate than metallic minerals and fuels, The U.S. Bureau of Mines estimated that the value of industrial minerals produced in 1963 was $4318 million vs. $2006 million for metals. Preliminary estimates for 1965 indicate that current value of production was again more than 2% times that of metals, thus making apparent their importance to the industrial life of the nation.

Jan 2, 1966

The Empire IV expansion is on schedule for completion in January 1980; Hibbing Taconite's 2.7 million ltpy* expansion should be finished late in 1979; and Reserve Mining's tailing disposal project is on target for April 1980. Erie Mining Co., the first to bring 170-ton haulage trucks to the Mesabi Range, reports excellent operating results, and Inland Steel expects to produce 80% of its pellets in 1979 using coal rather than oil. One Michigan mine has so many inspectors that it has hired a school bus to transport them around the operation; and a contractor reports that mine construction projects of the future may require the training of 15,000 workers. All of this was covered at the 52nd Annual Minnesota Section AIME Meeting and the 40th University of Minnesota Mining Symposium, a joint event held each January in Duluth.

Jan 3, 1979