Search Documents

By Joseph A. Norden, A. R. Willson

Much has been written concerning the hoisting equipment of various mines throughout the country, but most of the literature on the subject, if not all, describes equipment of extraordinary capacity and the small and medium-sized outfits have been neglected. The hoisting equipment here described is capable of handling about 1200 tons per day. It has not been worked to capacity, but 600 to 700 tons, together with men and materials, have been handled in two shifts without any great effort. Only one shaft extends from the surface to the lowest levels of the mine; see Fig. I. It is composed of three compartments, two of which are used for hoisting, and the third for water, air, and electrical lines, and for sinking purposes. In 1909, this shaft was raised from the 1000-ft. (304-m.) level to the 700-ft. There a station was cut and an air hoist installed. At this time all mining operations were confined to the upper levels of the mine; that is, above the 700-ft. The ore was dropped to this level through chutes from the 300-, 400-, 500-, and 600-ft. levels and then lowered in cars on cages to the 1000-ft., which is the main haulage adit, the mill and railroad bins being about 3000 ft. from the shaft. Orebodies were, in due time, developed on the 1000-ft. level and below. Therefore, in 1913,the shaft was sunk to the 1150-ft. level and thereafter sinking was continued at regular intervals until the 1500-ft. level was reached. But, hoisting from the 1300-ft. level was a difficult and slow process with the antiquated air hoist, so, in 1916, it was decided to raise the shaft to the surface and install a modern, electrically operated hoist. This was completed early in 1917 and the hoist was in operation in March of that year. The Hoist Figs. 2, 3, and 4 show various features of the hoist and electrical equipment. A Nordberg engine of the double-drum, geared type, designed for a 10-ton load, including rope, at a speed of 1500 ft. per min., is used. The drums are 7 ft. (2.1 m.) in diameter, with a 54-in. (137-em.)

Jan 1, 1922

By S. Razi

Injection luminescence of single crystals of rare-earth-activated CdS was investigated. Crystals of CdS:Nd, CdS:Er, and CdS:Yb, grown by the vapor transport technique, were suitably etched and hetero-junctions of Cu2S-CdS were fabricated on one side of the CdS substrate by chemical reaction. The device was then heated to 200°C in an inert atmosphere for 5 min. Static V-I measurements show that at low voltages (V < 1 v) the current is controlled by the junction, while at higher voltages the bulk Properties of the CdS substrate effectively control the current. Because of the large thicknesses no negative resistance was found. Reverse breakdown voltage varied from 5 v, for junctions that were not heat-treated, to 100 v, for diodes that received the proper heat treatment. The rectification ratio, measured in the range of 2 to 10 v, varied from 300 to 3000. Capacitance- voltage measurements indicate a weak dependence of the junction capacity on applied voltage. The capacity was found to increase appreciably with room light illumination. The variation of capacitance with frequency is indicative of a p+-i-n structure. An open-circuit voltage of 0.4 v was measured under an illumination of 100 mw per sq cm. Under forward bias, the bluish-green edge emission characteristic of CdS was observed. No sharp rare earth emission line was observed, which is in contrast to our results using ZnS:Tb, where, under high-voltage excitation, the rare earth emission was dominat over the lattice emission. The absence of rare earth emission implies that either the nature of the rare earth ion is different at the het-erojunction than in the bulk or the probability of energy transfer to the rare earth ion is small. RARE earth elements are playing an increasingly important role in the Synthesis of materials for a variety of purposes, e.g., solid-state lasers, color television screens, and so forth. Interesting systems result when wide-band-gap photoconducting lattices are activated with rare earths. A study of the lumines-

Jan 1, 1969

By E. M. Norris

In the summer of 1917 it was decided to fireproof the main Tramway hoisting shaft of the Anaconda Copper Mining Co. at Butte, Mont. The shaft has three hoisting compartments and one pump compartment; it is timbered with 12 by 12-in. (30.5 by 30.5-cm.) fir timber, and is 2475 ft. (754 m.) deep. Subsidence and displacement of the surrounding country rock had produced exceedingly heavy ground, and had carried the shaft out of line, in several places, by as much as 2 ft. (0.6 m.) displacement. Constant repairing and realigning of the timbers had been necessary in order to maintain clearance for the cages. The most feasible method of fireproofing, therefore, seemed to be to cover the timbers with a coat of concrete applied with the cement gun. The cement gun, which is operated by compressed air at ordinary mine pressures, feeds a mixture of sand and cement through a hose to a nozzle having a water connection. The mortar in fluid form is thus sprayed upon the prepared surface in thin layers, which can be built up to any desired thickness. The cement gun can be set up at any convenient point; satisfactory results have been obtained with the nozzle a distance of 500 ft. (152 m.) from the gun. The shaft was thoroughly overhauled and the timbers put in the best possible state of repair. Between the 1000 and the 1400 levels, much loose ground lay against the shaft timbers on the north side; this was breast-boarded back and a 30-in. (76-cm.) reinforced-concrete retaining wall was erected, leaving a space of 12 in. (30.5 cm.) outside the shaft timbers to allow for future movements of the ground. For convenience in handling men and materials, it was arranged to concrete the auxiliary hoisting-cage compartment and the pump compartment first, using the cages of the main hoist to serve the cementing crews. The auxiliary cage was then available while the remainder of the shaft was being concreted. A tight partition of 2-in. (5.08-cm.) plank was erected between the auxiliary and the adjoining hoisting compartments, for better protection of men riding on the cages. The application of concrete made this

Jan 1, 1920

By S. A. Hoenig

In an earlier publication, the application of exoelectron technology to the monitoring of dry grinding in a ball mill was reported. Recently, the author has investigated the ball mill problem in more detail with the system shown in [Fig.1]. Here, some of the current generated in the ore-ball-water mixture was picked up by the metal chains and served as a measure of the rate of grinding. While the mechanism of current generation has not been completely clarified, a parallel study of electrical effects associated with rock drilling indicated that the major driving force is the zeta potential*, while oxidation of the freshly fractured material provides the remainder of the current. Both of these effects are sensitive to the exposed surface area, and it might be expected that the observed currents would provide a measure of the grinding rate. This "surface area" effect allows the measurement system to be used in any type of rock or ore grinding. Some studies with sulfide copper ore indicate higher currents than those observed with silica sand, but the overall pattern of current versus grinding rate is essentially the same. Experimental Studies The experimental system was set up as shown in [Fig. 1]. The initial studies were done with silica sand because of its availability and for comparison with the data of reference 1. The sand was sized to an average of 425 /MI (40 mesh); a typical charge consisted of 2.5 kg (5.5 lb) of sand, 0.85 L (0.22 gal) of tap water and 2.5 kg (5.5 lb) of iron grinding balls 25.5 mm (1 in.) in diameter. For a typical "run," the mill was loaded with a fresh charge of ore and operated for periods ranging from 10-60 min. During this time, the current was measured with a Keithley 417 picoammeter and a chart recorder. At the end of the grinding period, the charge was removed and sieved to recover the 425, 300, and 212 µm (40, 50, and 70 mesh) fractions which were then drained and weighed. A fresh charge was used for each test and every attempt was made to keep the draining and weighing processes uniform.

Jan 1, 1985

By J. R. Eckel

It has long been known that mud properties affect drilling rate and that drilling with water is as much as six to .seven times faster than with mud. However, it is not known why drilling rates with mud are lower. Recent studies show what fluid properties govern microbit drilling rate and also provide a quantitative correlation of these fluid properties and hydraulics with microbit drilling rate. All the microbit tests reported in this paper were made with a low permeability (about 10 md) limestone. They were conducted at constant bit weight and rotary speed with varying fluid properties, flow rate Q and nozzle dinnteter d. The tests showed that (1) drilling rate in a given system with constant circulating rate and nozzle velocity is a function of the kinematic viscosity [viscosity /density, (cp)/ p (density)] of the drilling fluid measured at near bit nozzle shear rates; (2) the combined effect of fluid properties and hydraulics on microbit drilling rate is defined by a Reynolds number function (kQp/dp); (3) for the same kinematic viscosity, drilling rate is independent of solids content; and (4) for the same kinematic viscosity, drilling rate is independent of fluid loss. INTRODUCTION The fact that mudding up reduces rate of penetration is well known, but the reduction varies from well to well. The rate with mud may be 80 percent of the water rate or it may be as low as 15 percent. Since this reduction of up to seven-fold takes place under conditions of constant bit weight, rotary speed and mud circulating rate in a uniform formation, it can only be a result of the change in fluid properties. Previous work1-" both in field tests and in laboratory microbit tests) showed that drilling rate with mud is lower than with water (Figs. 1 and 2). Microbit tests also confirm, at least qualitatively, the field observation that drilling rate slows with increased pressure differential from borehole to formation (Fig. 3). The qualitative effect of drilling rate of bit weight, rotary speed and rate of mud circulation are also the same for the field and microbit rig. For these reasons, the industry generally accepts microbit results as being qualitatively meaningful in terms of field application.

Curiously enough, considering the relative accessibility of the two places, coal was reported at an earlier date in Saskatchewan than in British Columbia. Henry and Thompson were on the Saskatchewan River in February 1811, and on the 4th of that month recorded, while on Jack&apos;s Branch of North Brook, "I observed in one of the bends on the north side a bank of yellow clay, on which there appeared several horizontal veins of pure coal, of the best quality I have seen along this river." Later at Rocky Mountain House it was said: "a quantity of coal is tumbling into the water, as the current washes away the earth underneath. This coal abounds along the Saskatchewan, in some places forming solid beds several feet thick for several acres, which are washed by the river. In its pure state our smiths use it for the forge with equal proportions of charcoal made of birch or aspen, which answers every purpose for making and repairing our axles and other tools."1 It is needless to say that it was many years before this coal was used for any commercial purposes. Coal was first found on the northern end of Vancouver Island in British Columbia in 1835 at Beaver Harbor, where later Fort Rupert was established, where Indians had advised some of the Hudson Bay Company officials it would be found.2 The coal was used by smiths, and later on by the steamer plying along the coast.3 A report to the government in 1845 called attention to the coal reported in the neighborhood of Puget Sound and on the Cowlitz River, and that probably the samples used by the Hudson&apos;s Bay Company were obtained from the surface and. were not good. On September 7, 1846 a report on the coal situation was submitted by Ogden and Douglas, and a naval vessel was sent to investigate the report and was loaded with 62 tons dug out by the Indians, the seam outcropping along the shore.2 In 1847 some samples were sent to England by a returning war vessel. In 1849 the Hudson&apos;s Bay Company established a

Jan 1, 1942

By Geoffrey Purcell

For anyone contemplating flotation research with only a very limited amount of mineral available for testing, the choice of suitable experimental equipment is by no means obvious. Hallimond&apos;s original and delightfully simple cell1 has been modified by subsequent investigators2to give quantitative and reproducible results on small samples. However, the modifications have necessarily compromised its simplicity, and the services of a skilled glass blower are required to duplicate the cell. Vacuum flotation tests3 at best qualitative and may, under certain conditions4, be quite impracticable. A hundred years ago, Thoreau observed that "our life is frittered away by detail," and his advice was to "simplify, simplify," The success of the simple cell described below, which was developed by the author and differs somewhat from Hallimond&apos;s original, suggests that Thoreau&apos;s advice still has merit a century later. CELL CONSTRUCTION The cell [Fig. 1 (a) and 1 (b)] consists essentially of a 25-ml pipet from which has been cut the con- stricted top. The length cut off is not critical since this merely determines the final volume of the cell. Cell volume may be varied in this way from 20 to 50 cc. A pyrex extension tube, equal in diameter and approximately half the length of the cut pipet, is attached to the top of the pipet by means of 2 ½ in. of close-fitting tygon tubing. When assembled, the two pyrex tubes should be spaced about ½ in. apart. Another length of tygon tubing is added to the extension piece for sealing purposes. A ¾ -in. disc of porous material (teflon cloth is ideal), secured in place over the pipet tip with another piece of shaped tygon tubing, completes the cell assembly. Tygon tubing may be shaped by pushing it over the pipet tip or some similar form and heating carefully over a low flame. For flotation [Fig. 1 (c) 1, the pyrex extension tube is rotated approximately 70º from the vertical and held in position by a wire hook and eye. Floated material, after reaching the free surface, falls and rests on this inclined plane. The barrier formed by the bent tygon tubing ensures that floated material does not slide back and return to the vertical portion of the cell.

Jan 11, 1965

By Charles Baker

THE district of Catorce, San Luis Potosi, ranks among the first half-dozen silver-producing camps f Mexico. Mining has been more or less continuous there for 150 years. The large producing mines, Mapum, Mazapil, Palomas, Musquiz, Minas Virjas, now for the most part idle or abandoned, are grouped around the head of two valleys: one, which drains to the west, falls 2000 ft. (609.6 m.) in 4 1/2 mi. (7.2 km.) between the main Catorce and the western foot of the range and is characterized by steep canon walls; the other, east of the main town of Catorce from which it is separated by a high divide, heads in a number of steep tributaries above the basin in which lies the town of Potrero and flows nearly north for 10 mi. (16 km.) to the northern base of the range; below Potrero, it has for the most part gently sloping valley walls and a broad valley floor. The Sierra Catorce is the highest range of the region, the summits reaching altitudes of over 11,000 ft. With the exception of a few cliffs of the erosion escarpment of the lower limestone and the canon walls below the main town of Catorce, which is the highest town in Mexico, the gently rounded slopes are characteristic of a maturely eroded mountain range composed of folded sedimentary rocks. As is usual in desert regions, the heavy-bedded limestones are the most resistant to erosive forces. Folded into anticlines, they form the mountain ranges; and the intermontane valleys and basins, originally carved out of less resistant shales, clays, marls and sandstones, are covered by debris forming a mantle with surface gradually rising upwards toward the hills. In time, the debris buries, in deposits formed from their own ruins, all but the highest summits of the original mountains; some f this region has already nearly reached this stage. Most of the debris is firmly cemented by calcium carbonate (caliche). Solution f the limestone by meteoric waters afforded the supply of lime carbonate, which has been redeposited upon evaporation of the waters as a cement binding the boulders, pebbles, and finer detritus.

Jan 9, 1921

By G. L. Oldright

Nearly all of the present schemes for treating complex (i. e. lead-silver-zinc-copper) ores are based on the idea that lead holds, and will hold for some time, the strongest economic place from the viewpoint of supply and demand of all the non-ferrous metals. Copper, it is thought, will come back to its own when European affairs are stabilized, although at that time competition from Chile, Peru, and Katanga, in particular, will be more severe than in pre-war days. The future for silver and for zinc is uncertain. New uses are developing for zinc, and the market has remained better than many expected, but the stabilization of world markets will bring in foreign competition instead of relief. The cost of producing zinc from simple zinc ores, by the retort process, will, from the nature of the labor required and the increasing cost of fuel, increase steadily. As a result, the small producers of purely zinc ores around Joplin are shutting down their mines, even with a good market price for zinc; on the other hand, the producer of lead from complex ores, in the Rocky Mountain states, is confident of a profit from the sale of his lead, and is seeking means to make the zinc in his ore pay some part of the cost of treatment. However, the tonnage costs for mining and ore dressing are much higher in the Rocky Mountain states, as may be seen by comparing tax-return statements from the various states. Even before the recent drop in the price of silver, many mines were operating on a very slender margin of profit; labor and supplies cost more. Mining at greater depth has shown most orebodies to grow increasingly more complex, so that improvements in mining and ore-dressing practice have not been sufficient to compensate for the additional expense involved in beneficiating these ores. The smelters have bad to meet the same general economic situation, so they can only give

Jan 1, 1924

By F. D. Wright

Production of a coal preparation plant is governed by many restrictions, such as the tonnage of different products and blends that can be sold within a given period, capacities and output proportions of the cleaning and sizing units, blending proportions, quality specifications, and costs and prices for the various products. Determination of the tonnage of each product and blend that should be made in order to obtain the maximum profit can be difficult unless a systematic method such as linear programming is used. In this paper the basic method of linear programming is described briefly. The Old Ben No. 9 preparation plant is used as an example to illustrate in detail how eqwations can be written to form a linear programming model of a coal preparation plant. Three sample problems, each requiring 56 or more equations and 63 structural variables, were solved with an IBM 650 computer. Linear programming is one of several mathematical tools used for operations research. It has been applied to many fields and has been used by a number of industries either to maximize the profits of certain operations or to minimize costs. P. B. Nalle and L. W. weeks&apos; have described the use of the method by the Riverside Cement Co. to minimize the cost of blending raw materials to make portland cement. Their problem is to obtain at minimum cost a mix with certain specifications from a number of possible materials which have various costs and various amounts of CaO, SiO2, Fe2O3, and other constituents. In a paper on the use of linear programming by the National Coal Board in England, K. B. Williams and K. B. Halley2 describe how the transportation method, a variation of linear programming, is used to minimize the cost of sending 37 grades of coal from 28 mines to seven central washing plants which produce coal for furnace coke and foundry coke. The various coals have different percentages of volatile matter, moisture, sulfur, ash, and phosphorous, so there is considerable choice in how they can be blended to meet the specifications of the two products. The purpose of this paper is to show how linear programming can be used to maximize the profits of a coal washing plant which produces individual final products as well as blends. The Old Ben Corp. furnished assumed sample data from their Old Ben Mine No. 9 preparation plant for this investigation. However, the data that have been used are entirely the author&apos;s responsibility. METHOD OF LINEAR PROGRAMMING Numerous articles and books have been written on the theory and applications of linear programming.3-5 However, since the method has not been widely applied by the mining industry, a brief, nontheo-retical discussion of its basic method seems to be in order. Linear programming (Table I) is used to determine the best possible solution to a number of interdependent activities. It is essentially a method for making systematic selections from a number of possible solutions to determine positively the optimum solution. There may be other equally good solutions but no better ones. Each activity must have linear coefficients and there must be a criterion to judge how good the solution actually is. Linear programming is different from the solution

Jan 1, 1961

By R. D. Young, E. A. Harre

Nitrogen exists in two broad categories commonly designated as elemental nitrogen and fixed nitrogen. Elemental nitrogen is found in nature as a diatomic molecule and constitutes about 78%, by volume, of the earth&apos;s atmosphere. Fixed nitrogen is a common term used for nitrogen that is chemically bound to other elements. Although elemental nitrogen is very abundant, nonleguminous plants cannot utilize nitrogen unless it is in the chemically combined form. The content of this chapter is confined to fixed nitrogen since the uses and properties of elemental nitrogen and the fixed nitrogen compounds are different. Certain bacteria associated with legumes are able to fix atmospheric nitrogen, but not to the extent required by succeeding nonleguminous crops. The need to use fertilizers containing fixed nitrogen compounds to grow food crops has been recognized for hundreds of years, and from antiquity farmers have used organic wastes such as animal manures, vegetable wastes, sewage sludge, fish scraps, etc., containing these compounds for fertilizers. These organic materials have a low nitrogen content, however, and cannot support large-scale food production. Known commercial-size deposits of natural nitrates containing much higher nitrogen content exist only in Chile, and the possibility of the discovery of other significant deposits is remote. The Chilean deposits were the major source of nitrogenous fertilizers until the Haber-Bosch process for the production of synthetic ammonia was developed. In the Haber-Bosch process, nitrogen reacts with hydrogen at high temperatures and pressures and in the presence of a catalyst to form ammonia. Modern plants use air, water, and natural gas or other hydrogen sources to produce the ammonia that is now the key building block of the fixed nitrogen industry. Several major problems that developed in the 1970s continue with the nitrogen industry into the 1980s. These are (1) the continuing sharp escalation in the cost of feedstocks for ammonia production as well as all energy sources, and (2) the very steep increase in the investment cost of production facilities. More than 75% of the fixed nitrogen produced domestically is consumed as fertilizers. The types of materials used as fertilizers have changed significantly during the past years. There has been a trend from the use of low-analysis fertilizers to types which contain high percentages of plant nutrients. The average plant nutrient content (N + P2O5 + K2O) of fertilizers used in the United States has increased from 18% in 1930 to 32% in 1960 and today approaches an average of 44%. In the case of nitrogen fertilizers, the low analysis natural nitrates (16% N) gave way to ammonium sulfate (20% N) after about 1920. After World War II, ammonium nitrate (33.5% N) previously used in munitions, became established as the leading nitrogen fertilizer. Urea use as a fertilizer (46% N) began in the 1960s, and in the past 10 years has become the world&apos;s leading solid nitrogen fertilizer. Nitrogen Materials Anhydrous Ammonia-Anhydrous ammonia is a colorless gas at ambient temperatures and pressures and has a sharp pungent odor. Anhydrous ammonia is stored and transported as a liquid in high-pressure cylinders and tanks at ambient temperature, and in low-pressure tanks, barges, and ships at -28°F. Anhydrous ammonia is applied directly at 4 to 7-in. depths in the soil as a high-pressure liquid by special applicators, after which it expands to a gas that dissolves in the soil moisture or is absorbed on soil colloids. In other systems ammonia is metered into irrigation water and is thereby introduced into the soil.

Jan 1, 1983

By B. A. Shaw

Historically, microwave tubes have been fabricated from massive metal and ceramic components. The current trend is to lighten tibes for airborne applications. The reqciiremenls of light weight and also reduced cost have created a novel approach to tube structure in which thin-film technology plays a major role. Although the electrical requirements of thin-film circuits in microwave tubes differ from those required or se,niconductor integrated circuits. the technology is basically similar. The stringent requirements of the micvowave tube have created sophisticaled thin-film techniques thut are of interest to the integrated-circuit industry in general. This paper describes a nunzber of thin-jilm techniques recently developed and discusses in detail the application of the technology in microwave tubes. The particular areas of interest are: 1) ceramic mounted thin-film slow-wave structures; 2) thin-film secondary emitters; 3) suppression of tube environnental multipactor by semiconducting&apos; thin films; and 4) age-hardenable and dispersion-hardened thin metal films. SEVERAL thin-film techniques specifically applied to microwave power tubes are discussed in this report. There are two reasons for this work. One is the necessity of reducing weight and cost of microwave tubes and the other is related to overcoming problems in the tube operation by the use of applied thin-film technology. The major emphasis of this work has been on tube slow-wave structures. Other work in the area of secondary emission, either its suppression or its enhancement, is continuing; the most satisfactory results to date have been by utilization of thin-film technology. The requirements of high thermal and electrical conduction together with greater strength than normally obtained with elemental materials have led to the development of dispersion-hardened films. The paper will discuss: 1) ceramic-mounted delay-line microwave tubes; 2) multipactor and secondary emission; 3) hardened films. I) CERAMIC-MOUNTED THIN-FILM SLOW-WAVE STRUCTURES In a conventional crossed-field microwave tube, the slow-wave or delay-line structure is produced from two carefully machined components. One half of the structure is shown in Fig. 1. The other half is the mirror image of the first but is rotationally offset by a half a period. The combined structure now forms an interdigital type of slow-wave structure and is the anode of the tube as shown in Fig. 2. The period and finger length of an interdigital slow-wave structure are prescribed by the desired dispersion characteristics. The typical design is as shown in the first figure; it can be noticed that the finger width is several times greater than the finger thickness. Even assuming that it were mechanically possible to produce free-standing fingers of extremely small cross-sectional dimension, for example, 0.002 in. thick by 0.005 in. wide by 0.500 in. long, decreasing this finger width would increase the tube efficiency but would also decrease the thermal-conduction path, causing an increased temperature rise from intercepted rf current which in its extreme could easily cause finger melting. Hence, for free-standing lines of this type, the design is a compromise between mechanical capabilities, tube efficiency, and thermal dissipation. These structures are also expensive and tend to be heavier than purely electrical considerations would demand. In the present approach, we have transposed the three-dimensional structure previously shown into an essentially two-dimensional structure as shown in Fig. 3. The linear structure is used here for clarity of detail. The support member is a ceramic material and the line is deposited copper. The final tube design is shown in Fig. 4. Because of the backwall sup-

Jan 1, 1967

By L. T. Sanchez, W. T. Rogers

This paper presents the results of a production experiment evaluating the effect of the use of oxygen in the bessemer converter with respect to its relation to blowing time, amount of steel scrap or cold pig iron which can be melted and teeming temperatures of the molten steel. THE simplest and probably the most efficient and economical means for producing steel from molten pig iron is the bessemer converter. This process is essentially a mechanism for bringing oxygen into contact with the molten metal thereby oxidizing the elements silicon, manganese, and carbon. The source of oxygen is that contained in the air and is limited by that amount. In theory, there is an intermediate chemical reaction due to the mass action of iron and air which is represented by the equation: 2Fe + O2- = 2Fe0 The FeO then becomes the oxidizing agent and reacts with the silicon, manganese, and carbon to produce silicon dioxide (SiO,), manganese oxide (MnO), and carbon monoxide (CO), in the order mentioned. The balancing of the various chemical reactions shows that in the ordinary bessemer process more than sufficient oxygen is delivered to satisfy these reactions, which indicates that a further increase in the oxygen content of the air would serve no useful purpose. In spite of this reasoning, however, it will be demonstrated that when melting stelel scrap, commercially pure industrial oxygen introduced into the normal air blast will permit the melting of a larger proportion of steel scrap than is possible with air alone and also will increase the production rate by a substantial reduction in blowing time. It will also be shown that when melting cold pig iron, it is possible to melt up to twice as much pig iron with the use of oxygen as can be melted without added oxygen with a nominal increase in blowing time. At the plant where this study was made, oxygen is purchased from a nearby supplier and piped directly into the plant. It is supplied to the bessemer converter by being introduced directly into the blast line through an automatic control system which may be adjusted by the bessemer operator or "blower." Normally, iron is supplied by five blast furnaces to an open hearth shop containing twelve 165-ton capacity stationary furnaces and a bessemer converting shop having three 30-ton converters. The molten metal from the blast furnaces is allocated to one shop or the other in a manner to best provide for maximum production. At various times, it is desirable to direct the maximum amount of available blast furnace production to the open hearth shop. This has the effect of reducing the production of the bessemer shop. When this condition exists, it is desirable to supplement the reduced iron charge at the bessemer with steel scrap or cold pig iron to the maximum possible extent in order to maintain high total ingot production. This condition becomes aggravated when one of the blast furnaces is taken out of production for any repair job and particularly for extended periods such as when relining is necessary. The purpose of the investigation and experimentation with oxygen was to determine whether or not it would contribute to increased flexibility in the use of the raw materials, molten iron, steel scrap, and cold pig iron. In addition to the effect of oxygen on flexibility of operation, it was also necessary to determine the relation of its use to production rate or "blowing time," final finishing temperature of the steel or "teeming temperature," and steel quality.

Jan 1, 1953

By R. W. Olson, A. L. Benham

Viscous fingering was studied as it occurred in an open Hele-Shaw model (1 ft x 4 ft x 1/16 in.); it was also studied in the same model packed with 80-mesh glass beads during miscible displacements under unfavorable viscosity ratio conditions. It was determined that the lengths of 20 elements of the front were distributed normally around the average position of the combined elements under all conditions. Represented by the normal distribution, the length of the viscous fingers grew linearly with the distance traveled from the point of finger formation, increased with displacement velocity, and increased with increasing mobility ratio. Results obtained during the first few inches of displacement were of little or no use in predicting finger growth and/or finger length throughout the 4-ft model since the point of finger initiation cannot be predicted and would often occur several inches from the point of injection with either positive or apparent negative coordinates. The fingering occurring during a miscible slug displacement was much greater than would be predicted based upon the actual mobility ratios between in-place fluid and slug and between slug and following fluid, using the results described above for miscible displacement in the absence of a slug. Many of the experiments in the packed model showed that the rate of growth of the viscous fingers was diminishing toward the end of the displacement in the 4-ft long model, indicating that microscopic mixing, such as diffusion or dispersion, was decreasing the viscous fingering effect. INTRODUCTION Viscous fingering is a manifestation of a finger-shaped interface between displaced and displacing fluids occurring during typical miscible displacement projects for oil recovery. Its cause may be traced to the instability of a viscous fluid being displaced by a more mobile fluid. Viscous fingering takes on important significance in the miscible slug process 1.2 where it may be a dominant factor in determining minimum slug size. Experimental1-3 and theoretical4-7 studies of viscous fingering have been made by other investi- gators. However, an exhaustive study of the variables affecting viscous fingering had not been made. The present study was undertaken in an effort to determine the effects of some of the more obvious variables—such as mobility ratio, displacement velocity, distance displaced, and packing—upon viscous finger length and growth in a small laboratory model. It does not necessarily follow that conclusions reached by studying the results of this model study may be applied to the field. Future studies would have to evaluate the effect of model size on extension of these results. EQUIPMENT AND EXPERIMENTAL PROCEDURES A flow diagram for the equipment used in this study is shown in Fig. 1. Basically, it consisted of (1) a constant-rate pump for the injection of displacing fluid into (2) a model made up of two flat transparent plates spaced a small distance apart and (3) provisions for the production of fluid into a calibrated graduate. The displacing fluid contained a dye which allowed visual observation of finger spacing and length. The pump performed at rates from 2.5 cc/hr to 480 cc/hr, while pumping a light mineral oil into a bladder in a closed glass container holding the displacing fluid. The model was made up of two plates of 1-in. Plexiglass with dimensions 1-ft wide by 4-ft long. These were spaced 1/16 in. apart so that the internal model dimensions were 1-ft wide x 4-ft long x 1/16

S. Tandanand, Twin Cities Mining Research Center, U. S. Bureau of Mines As an addition to the fine reviews on drilling presented in the foregoing papers, we feel it would be appropriate to mention briefly some work in this area by the U. S. Bureau of Mines. The Bureau has had under way for several years at its Twin Cities Mining Research Center studies directed toward a better understanding of basic drilling mechanisms. The work includes drillability investigations with diamond rotary, and with percussive drilling systems, as well as fundamental studies of rock behavior under drill bit types of loading. Results of our work to date have contributed the following to the state of the art. MECHANISM OF ROCK FAILURE-Rock fragmentation through use of mechanical energy systems, including drilling systems, consists of two major components-machine and rock. The two components are related to each other by their functional behavior and their resultant motion which the components mutually influence. Forces in the systems are transmitted directly to the bit which in turn induces stresses in the rock. When the induced stresses exceed the strength of the rock, the rock fails resulting in penetration. Rock strength is a function of the forces applied to the rock. Stresses under a drill bit, regardless of bit configurations, are essentially compressive, resulting in a condition where the rock has the highest resistance to failure. The ratio of principal stresses induced under drill bits is an indication of the mode of failure in the rocks. Initially, compressive stresses under the drill bit cause rock to undergo inelastic deformation. The impression observed at the first stage of crater formation under the drill bit shows that rock is no longer elastic. Associated subsurface failure at this stage precedes total rupture which subsequently appears at the rock surface. Thus, explanation of crater formation, by applying theory of elasticity alone, is likely to be over-simplified. ENERGY VERSUS VOLUME OF ROCK REMOVED-Experimental results show that energy per unit volume of rock removed is constant for a particular rock and bit type. Rock offers a definite resistance to penetration, depending on the method of the energy application; this may be defined as the drilling strength of a rock. Energy consumption in a drilling system may be divided into two components: 1) Energy required to move the machine parts; and 2) energy consumption in breaking rock. Component 1 is dependent on the type of the machine. Component 2 is dependent on the strength properties of rock and the efficiency of the bit in rock cutting. The sum of the energy required in both components determines the total energy required in breaking rock. Our work in this area has included consideration of both diamond and percussive drilling systems. PENETRATION RATE-For a drilling rate expression to be useful in predicting field performance, it should include the operating characteristics of the drilling machine. Eq. 37, for example, is simply a statement of the fact that the drilling rate is determined by the power output of the machine (2pNT) and the power requirements to break the rock in the hole (AER). In order to predict the performance of a particular drill and the effect, for example, of the rotary speed, on the drilling rate, R, Eq. 37 must be modified to include the

Jan 1, 1967

By C. W. Phillips, D. N. Frey

A commercial Ti-Fe-Cr alloy, Ti-150, exhibits a martensitic transformation on cooling and two nucleation and growth reactions, one above and one below the Mg-Mf region, on isothermal holding below the single-phase ß temperature range. The reactions were followed by metallographic, X-ray diffraction, and microhardness methods. THE rapidly expanding engineering application of titanium and its alloys makes increasingly urgent an adequate knowledge of the effect of heat treatment on this material. The work herein reported is an attempt to determine certain aspects of the behavior of a commercially available alloy, Ti-150, during heat treatment. The alloy, with a nominal composition of 2.7 pct Cr, 1.3 pct Fe, 0.25 pct 0, 0.02 pct N, and 0.02 pct C, was received in the as-rolled condition as a 3/4 in. round. Slugs 0.11 to 0.12 in. thick were cut under a coolant using a silicon carbide wheel. Preliminary work established that the alloy consists of two phases, a (hexagonal close-packed) and /3 (body-centered cubic), at temperatures below 1750" to 1775"F, and of only /3 phase at higher temperatures. The slugs were heated for 1 hr in air at 1800°F to form a single-phase /3 matrix, then transferred to molten tin (1250° to 1650°F) or lead (1150°F and below) for isothermal holding. Holding temperatures ranged from 700° to 1650°F, times from 0.001 to 23 hr. The treated slugs were then sectioned, one part for metallographic examination and diamond pyramid hardness, the other, after deep etching to remove the high oxygen surface,&apos; for comparative lattice parameter determination and X-ray phase identification. Hardness measurements were taken on the lightly etched surfaces of the metallographic specimens; a 1000 g load on a 136° diamond pyramid was used. Five impressions on each sample were made and the average of the hardness calculated. The use of microhardness measurements to follow the course of an isothermal transformation reaction is undesirable because of the possibility of wide differences in microconstituent hardness.&apos; They were used in this case, however, because of the small amount of material available. At the higher transformation temperatures, where the above-mentioned objection was apparent, the readings were proportioned to correspond to the estimated ratio of transformed and untransformed constituents present. At lower temperatures, resulting in much finer microconstituents, the microhardness measurements were more uniform. The standard deviation of the mean of five impressions calculated from these latter values was 4.2 DPH. Employing 2a limits (probability 0.95) the experimental error of the hardness measurements averages was 8.4 DPH. The etchant used was composed of one part glyc-erol and one part 48 pct hydrofluoric acid." Of a number of etches tried, this one appeared most satisfactory. All micrographs were taken at 500X magnification and with oblique lighting to permit easier identification of the acicular structure resulting from rapid cooling. No advantage was gained by using polarized light for metallographic examination. Phase identification and lattice parameter measurements were made with a North American Philips high angle spectrometer in conjunction with a recording potentiometer. Considerable difficulty was encountered with some of the lattice parameter measurements because of the extreme broadness of the few diffraction lines obtained from samples consisting mainly of strained, untempered, quenched structures.

Jan 1, 1953

By F. G. Miller, T. D. Mueller, L. B. Davidson

A mathematical model of reservoir behavior during one cycle of the intermittent steam injection process is presented in this paper. A cycle of the process is considered to be composed of three stages: injection, condensation and production. The model concentrates on behavior during the production stage. The influence of several parameters on production improvement is described, using the results obtained with a numerical equivalent of the model. Reservoir system parameters considered are thickness, reservoir thermal conductivity, oil viscosity, solution gas-oil ratio and the change in oil effective permeability with temperature. Operating parameters investigated are heat injection rate, steam temperature and cumulative injection time. In the face of considerable uncertainty, the model appears to give a fair prediction of the behavior observed during an actual test. This makes the model a useful means of selecting projects. It is shown that the model may also be utilized to select an optimum set of operating conditions for a particular project. Results of this study show the extent to which production improvement depends on each of the parameters investigated and give an indication of the range of system conditions within which the process would be effective. INTRODUCTION In recent years the intermittent steam injection or steam soak process of oil recovery has become a popular method of improving recovery in reservoirs bearing high-viscosity hydrocarbons. Production improvement due to the process results from heating the reservoir near the wellbore. The process is applied on an individual well basis and is executed in a series of cycles, each consisting of three stages: injection, condensation (the soaking period) and production. During the injection stage, high-pressure steam is injected into the reservoir surrounding the well-bore. This study assumes that injection is carried out over the entire vertical section of the reservoir rock that can be exposed to fluid injection. The condition of steam entering the reservoir is considered to fall within the following limits: (1) steam pressures less than 1,000 psig, (2) steam temperatures between 300 and 700F and (3) steam quality less than 90 percent. The last restriction is due to equipment limitations. Normally, injection re maintained for less than 3 weeks. After termination of injection, the condensation stage begins. The well is shut in for several days, supposedly to make certain that the injected steam condenses. This condensation would insure the retention of injected heat. The production stage is initiated when the well is opened again. Reservoir response during this stage determines the effectiveness of the process (response is defined as the oil production rates, the water production rates and the wellbore temperatures observed during the entire production stage). The immediate response of the reservoir is sometimes quite good. Sets of case histories by Longl and by Owens and Suter2 give some typical figures for response. Duration of the production stage is equal to the time needed for the oil production rate to decline to some predetermined value. This usually requires 4 to 6 months. Termination of the production stage coincides with the start of the next cycle. The process is continued, cycle by cycle, until it becomes unprofitable to continue. One simple model2 and two more sophisticated models3,4 of the process have been presented. These are based on fundamentally different assumptions than those used in this investigation. Although the three models might be modified to fit the assumptions used in this study, it is felt that greater rigor would result by developing a

By M. Bevis, A. G. Crocker

A. G. Crocker and M. Bevis (Battersea College of Technology)— Richman and Richman and conard17 have recently published the very interesting results of their studies on the plastic deformation of Fe-Ni-C martensites and of an Fe-5 wt pct Be alloy. Other work on the range of Fe-Be alloys containing between 16 and 27 at. pct Be has also been reported by Richman." One of the fascinating features of this work is that the materials investigated deform primarily by means of twinning and that several twinning modes are operative in addition to the well-established (112 ) mode of bcc materials The composition planes of these unusual twins were determined using a single-surface analysis and reported as (0131, "{045)" or "{089)", and "{2,3,10)" or "(127)". (It is now thought1&apos; that the "{0,1,13)" habit reported for the Fe-Ni-C alloys&apos;&apos; is more likely to be near "{127)". Although the full twinning elements of these unusual twinning modes could not be determined directly from the experimental results, the authors attempt to deduce the elements by considering twin intersectionslQ and by using the projection technique of Jaswon and Dove.&apos; The basic assumption of their approach is that the (013) habits are truly rational planes but that the other habits are irrational and merely approximated to by the indices quoted above. They thus deduce that the twinning mode describing the (013) habit is either Type I or compound and that the modes describing the other habits are Type 11. This deduction must however be false as all twinning modes in cubic structures obeying the classical orientation relationships of deformation twinning must be compound. Type-I and Type-I1 modes can occur in all of the other crystal systems (indeed in the triclinic system compound modes are not allowed), but in the cubic system only compound modes can arise. This fact, which does not appear to be well-known, fol- lows immediately from the relations between the four twinning elements defining a twinning mode. Thus for a Type-I mode which is uniquely defined by the rational twinning elements K1 = hi and tj2 = vi (i = 1, 2, 3), the Kz qd 771 elements are given by: where the summation convention of the tensor calculus has been adopted. For cubic materials the metrics cij Iand cij reduce to the unit tensors 6ij and 6ij so that we have It is clear from these equations that both ki and ui must take on integral values; i.e., Kz, and ql must be rational, if hi and vi are integers, i.e., if K1 and 77~ are rational. Thus for cubic materials a Type-I mode must degenerate into a compound mode and the same result also arises for Type-II modes. The apparently irrational habits observed by the authors can thus not be explained in terms of Type-I1 twinning if the classical laws of deformation twinning are to be obeyed. An alternative explanation of the irrational habits is that they may arise from twinning modes with four irrational twinning elements. These modes, which do not obey the classical orientation relationships associated with deformation twinning, have been shown to arise as the result of double twinning processes in magnesium,22 but may also describe a simple shear on an irrational plane in an irrational direction. Indeed double twinning processes in bcc

Jan 1, 1963

By Henry P. Chandler

Tripoli is the general name for a number of fine-grained, lightweight, friable, minutely porous, forms of decomposed siliceous rock, probably derived from siliceous limestones or calcareous cherts. Tripoli is often confused, both in the trade and technical literature, with tripolite, a diatomaceous earth (diatomite), found in Tripoli, North Africa. A material found near Seneca, Mo., resembling tripolite was incorrectly termed "tripoli." This name has persisted and now has a definite physical and trade meaning. However, tripoli contains no diatoms, is of an entirely different origin, and has chemical and physical properties different from those of tripolite. There are two distinct types of tripoli in the United States; that from the Missouri-Oklahoma field and that from the Southern Illinois field. Commercially the term "tripoli" is applied to the material from the Missouri-Oklahoma field, while the material from the Southern Illinois area is often referred to as "amorphous" or "soft" silica. Material similar to the Missouri-Oklahoma tripoli, but finer grained, occurs in northwestern Arkansas. In its Minerals Yearbook the Federal Bureau of Mines groups statistically under "natural silica abrasives," tripoli from these producing areas and rottenstone from Pennsylvania. The justification for this grouping is the similarity of use. Composition and Physical Properties Commercial tripoli contains 97 to 99 pet SiO2. The remainder is mostly alumina, iron, lime, soda, and potash, some of which may impart desirable physical properties to the material. Variations in the chemical composition of tripoli are not as important as its physical characteristics. The color of tripoli varies from white to cream, brown, rose, and red, the variations from white being the result of iron deposited from percolating surface waters. The commercial varieties of tripoli mined in the Missouri-Oklahoma area are designated as cream and rose. Other physical properties of the tripoli from this area are: Free quartz, less than 0.5 pct; oil absorption, 50.71 to 53.14 pct; water absorption of the crude tripoli, about 38 pct, and of prepared material, about 52 pct; fracture, uneven to conchoidal; specific gravity, 2.15 to 2.62; weight per cubic foot crude, 35 lb, ground, 55 lb; fusion point, 3,225° to 3,300°F; and refractive index, 1.54. Tripoli occupies about 1 cu yd to the short ton in place and about 1.5 cu yd when broken. Packed for shipment, the powdered material occupies about 33 cu ft to the ton. Its value and usefulness depend primarily on a low content of crystalline silica, size of the natural particles, absorption, and color. Some beds in the Missouri-Oklahoma area are of sufficiently compact material that large, fairly strong blocks may be removed. These find a market as filter blocks and have been used for building material. In the Southern Illinois field the color of the material is the important physical property; pure white is preferred. The rottenstone mined in Pennsylvania is of higher density and lower in silica content than the various types of tripoli. Its composition approximates 60 pct silica, 18 pct alumina, 9 pct iron oxide, 8 pct alkalies, with small amounts of lime and magnesia. The material apparently is a ferruginous and siliceous shale, having properties rendering it suitable as an abrasive or as a filter for paint, rubber, and plastics.

Jan 1, 1960

By J. P. Martin, A. H. Geisler, J. H. Crede, E. Both

The investigation of a 50 pct Co alloy was undertaken to determine whether there was any direct correlation between the structure and properties of Co-Fe alloys which were given various magnetic heat treatments. The magnetic anisotropy and texture of the 0.002-in. cold-reduced 98 pct material tend to decrease and change in nature with increasing temperature of the recrystallization anneal. Annealing samples in a magnetic field had little effect on either the magnetic properties or texture. However, cooling them in a magnetic field greatly improved their magnetic properties. THE beneficial influence of a magnetic field applied during the heat treatment of certain soft magnetic materials has been known for a long time. Early work showed that the presence of a magnetic field of a few oersteds during the heat treatment of Fe-Ni alloys will cause a large increase in maximum permeability. A pronounced increase in the residual induction which is produced by the magnetic anneal causes the hysteresis loop to approach the shape of a rectangle. Such results are beneficial since the desired properties are high permeability, high induction at maximum permeability, high residual induction, and low coercive force. More recently Libsch and coworkers1 studied the effect of magnetic annealing on the hysteresis properties of a series of Co-Fe alloys prepared from powders. They observed good response for the 35 and 50 pct Co alloys but little response for the 42 pct Co alloy. They pointed out that this was somewhat surprising since the 42 pct alloy has a high linear magnetostriction and zero crystal anisotropy and similar conditions in Fe-Ni alloys give excellent response to magnetic annealing. They found optimum properties to be at the 50 pct composition with residual induction, Br = 19,000 gauss and coercive force, Hc = 0.68 oersteds after the magnetic anneal. Before the magnetic anneal these values were B, = 12,600 gauss and Hc = 1.15 oersteds. The optimum treatment consisted of cooling from above the y-a transformation temperature to 900°C in a field of 20 oersteds, holding 11/2 hr at 900°C, then cooling at a rate of 20° to 25°C per min in the field to below 230°C. Cooling rate mainly affected coercive force with the value decreasing from 1.09 to 0.88 oersteds as the rate was increased from 3° to 48°C per min. Cooling from 1020" to 900°C in a field followed by further cooling to 230°C without the field gave properties decidedly inferior to those for samples annealed with the field applied throughout the cooling. They concluded that to get the best properties the samples must be cooled in a field to a threshold temperature above which the alloy is plastic enough to be affected by magnetostriction. In this respect the holding temperature must be high enough so that the alloy exhibits good plasticity to permit the optimum orienting of magnetic domains by relaxation of magnetostriction. In contrast, the holding time was of less significance for there was little improvement when the time exceeded 1/2 hr. The improvement in properties effected by magnetic annealing has usually been attributed to the establishment of a domain texture caused by the "freezing in" of magnetic strains. On the other hand, Smoluchowski and Turner2,3 apparently found that a magnetic field applied during recrystallization could alter the crystal texture. If this effect is real, improved properties would also be expected when

Jan 1, 1954