Search Documents

By Charles E. Locke

DEPRESSION in all lines of the mineral industry except gold, which began in 1930 and continued, even worse, through 1931, had its effect on ore concentration. Construction was limited to the completion of plants already begun. Every possible economy was adopted. Changes and improvements involving expense were postponed. Research was largely abandoned. Operations became highly efficient and costs were cut down, although this did not necessarily mean a lower cost per ton because of the greatly reduced capacity at which mills were run. Lower metal prices caused the operators to seek the optimum ratio of concentration and grade of concentrates looking toward maximum economic recovery; that is, net profit. In the crushing field no marked changes occurred. The Symons cone crusher for intermediate work is in use almost everywhere. Its manufacturers claim that 900 machines have been installed in 21 countries, replacing two previous steps of crushing and yielding a product sufficiently fine to form a satisfactory feed for rod mills and ball mills. A new Telsmith crusher has appeared which has curved jaws something like the Symons cone and consequently the same advantage as the latter.

Jan 1, 1932

By Michael D. Balen

During the years 1987 through 1989, the Bureau of Mines Alaska Field Operations Center (Bureau) in cooperation with the Western Field Operations Center and the Alaska Division of Geological and Geophysical Surveys (ADGGS), conducted mining, geological, and geochemical investigations in the 5.7 million-acre Valdez Creek Mining District (VCMD). This investigation was conducted as part of the Bureau's continuing Mineral Land Assessment (MLA) mining district studies program. The Bureau's MLA program is designed to provide reliable and comprehensive mineral resource information that supports mineral resource policy and land use decisions made by Congress and Federal land management agencies. The information also provides the basis for decisions that would expand the domestic supply of important mineral resources, primarily strategic and critical minerals. Much of the MLA work is done jointly with cooperating State or U.S. geological surveys.

Jan 1, 1992

By E. L. Singleton

This Bureau of Mines investigation was initiated to study and establish some of the chemical and physical characteristics of the condensed Mno-Si02 system. To prevent oxidation of the manganous ion, I atmosphere of purified helium was used in the furnaces. Solidus-liquidus curves and invariant points were established from melting-point determinations and were supplemented from data obtained by the static-quenching method. Experimental findings and data are for the intermediate compounds of tephroite and rhodonite with their respective eutectics represented at 25.5 and 37.2 weight-percent silica. Tephroite melts congruently at 1,347° C., and rhodonite melts incongruently at 1,286° 8.. A metastable transformation was determined to exist at the 1,347° C. isotherm, the congruent melting point of tephroite. A composite X-ray-diffraction pattern was formulated for synthetic rhodonite. This investigation contributes fundamental data leading toward a better understanding of the more complex slag systems.

Jan 1, 1962

By L. G. Stolarczyk, Y. Luo, S. S. Peng

Detection and assessment of severe geological anomalies ahead of a longwall face greatly benefits the mining operation. Electromagnetic-based Radio Imaging Method (RIM) is one of the most promising geophysical methods for this task. Based on two decades of development, the latest RIM instrumentation (RIM-IV) has expanded its operational range up to 1,800ft.A site demonstration of the RIM-IV technology was recently conducted within a longwall panel. An extensive ground truth study was performed to evaluate the accuracy of the RIM survey results. This study compared the generated RIM tomograms of attenuation rate with the mapped geological anomalies. Three different approaches have been employed to examine the accuracy of the RIM results and to correlate the measured signal attenuation rates with physical properties of the coal seam. The study shows that the RIM-IV technology is able to identify and delineate those geological features that would severely affect the longwall mining operation.

Jan 1, 2004

By Donald F. Reed

In the Coastal Plain sedimentaries of northeastern Mississippi, high-alumina clays and kaolins, which are bauxitized locally to varying degrees, are found in many places along the contact between the Midway (Paleocene) and the Wilcox (Eocene) series. The trace of the contact extends from Tippah County, on the Tennessee border, south to Winston County, thence southeast to Lauderdale County, and into Alabama. Its length within Mississippi, disregarding sinuosities, is 185 miles (fig. 1). Commercial production of bauxite from the region has amounted to about 400 tons, shipped from one outcrop in Komper County. In December 1941 and January 1942, the Bureau of Mines and the Federal Geological Survey made a reconnaissance survey of the contact zone and selected the most promising areas for further study. In 1942, four areas in Benton, Union, and Pontotoc Counties were investigated by auger and rotary core drilling, and in 194, core drilling was done on five areas in Kemper, Noxubee, and Winston Counties. The present report records the work done by the. Bureau of Mines and the factual data obtained from the investigations of the nine areas in the two projects.

Jan 1, 1952

By J. Y. Hascoet, M. Marya, S. Marya

Additive manufacturing (AM) brings disruptive changes over the ways parts and products are designed, tested, qualified, assembled, inspected and marketed. With these changes come real technical challenges, therefore, concerns that mainly stem from the maturity and diversity of today’s AM processes, the feedstock materials, and the interactions between the numerous process parameters. Additive manufacturing is somewhat similar to laser and electron-beam conduction-mode welding and involves a multitude of dynamic physical events between projected feedstock and moving heat source that influence process robustness, thus deposit properties. For this paper, a simple air vent, selected for its size, thin-wall, hollow geometry and materials (specifically 316L) was made using a laser-based powder blown technology (Construction Laser Additive Direct or CLAD) and systematically inspected by optical microscopy, microhardness indentations, and electron-back-scattering diffraction (EBSD). This exemplary part is first analyzed to broadly discuss metallurgical phenomena in additive manufacturing, particularly solidification and texture development. The paper then expands to other alloys and continues correlating metallurgical observations to process parameters and part properties, also borrowing from past experience with the same 3D printing CLAD system.

Jan 1, 2014

By Roger Payne, John R. Goode, Feng Gao, James Brown

The Eco Ridge deposit is located in the Elliot Lake mining camp in Northern Ontario, Canada. Between 1955 and 1996, the area produced more than 138,000 t (300 million pounds) of U3O8 and very significant amounts of thorium and heavy rare earths. Based on the NI 43-101 Preliminary Economic Assessment by Roscoe Postle Associates (RPA) dated June 2012, and the economic review by RPA as announced in Pele Mountains’ Press release dated September 12, 2013, the Eco Ridge Mine Project would extract and process 46 Mt of material to produce about 19,000 t (42 million pounds) of U3O8 and about 65,000 t of rare earth oxide (REO) over a 14-year life. This paper discusses process optimization studies including beneficiation and hydrometallurgical testwork. The proposed modified flowsheet includes the flotation and processing of 1) a pyrite concentrate, 2) a dominantly light rare earth elements (LREE) concentrate, 3) a concentrate containing most of the balance of the uranium and heavy rare earths (HREE), and 4) a relatively inert tailings.

Jan 1, 2014

By D. Harrington

We Americans fondly believe that ours is the greatest , most progressive and most civilized country in the world , but the cold statistical facts reveal that we apparently have little appreciation for the lives of those whose efforts of various kinds give us whatever greatness we have . The latest available statistics indicate that the annual death rate per 100,000 persons , from accidents is nearly 80 , or far higher than that of any other country in the world ; it is more than double the rate in Denmark , Belgium, Netherlands , France , Sweden , Italy , Ireland , Germany , Norway, and Austria; it is practically double the rate in England and Wales and in Japan , and is from 25 to 60 per cent higher than the corresponding rate in Scotland , New Zealand , Australia, Switzerland , and Canada . And added to this is the fact that of the main industries of the United States mining has by far the worst accident record , viewed from either the frequency or the severity basis . The National Safety Council's latest figures for 27 of the country's main industries give mining the highest or worst accident frequency rate, 74.43 in 1929 ; meat packing comes next with 55.94 , and construction third with 50.41 . In accident severity in 1929 mining also was the worst offender , with a rate of 9.99 ; quarrying is second with 6.11 , and construction third with 4.62 . Metal mining's frequency rate in 1929 was 52.16 , as against 69.25 for bituminous coal mining ,99.68 for anthracite mining, and 74.43 for the entire mining industry ; accident severity for metal mining in 1929 was 5.99 , as against 11.69 for bituminous coal mining , 10.87 for anthracite mining , and 9.99 for the mining industry as a whole . Although this figure indicated that metal mining is on a much safer plane than either bituminous or anthracite coal mining, the frequency rate of 52.16 for metal mining was higher in 1929 than the frequency rate of all but one of the other 26 industries about which data are available ; the metal mining severity rate of 5.99 , while much better

Mar 1, 1932

By Yves-Laurent Turcotte

Notre conférencier, Monsieur Yves L. Turcotte, Vice-président et Directeur général chez Promaintech Novaxa est diplômé en génie industriel de l?Université du Québec à Trois-Rivières et détient une maîtrise en gestion de projets de l?Université du Québec à Montréal. Il est une véritable sommité canadienne dans le domaine de l?amélioration de la performance des organisations. Provenant d'entreprises manufacturières et de services, il possède plus de 20 ans d?expérience en tant que développeur de technologies, conseiller et formateur auprès d?entreprises. Il a à son actif la réalisation de mandats dans plus de 400 entreprises. Il est reconnu pour sa grande capacité d?analyse et pour trouver des solutions novatrices et profitables aux problèmes des organisations les plus complexes. Aujourd'hui, il dirige Promaintech Novaxa, une division de DMR, qui a célébré son dixième anniversaire en 2006. Cette organisation ayant des places d?affaires dans la région de Montréal, Québec et Vancouver compte plus de 50 professionnels et a une carte de visite dans 16 pays. Les axes d?intervention sont le Management, la Productivité, la Fiabilité, l?Innovation et l?Amélioration Continue.

Feb 1, 2008

By Davorin Kolic, Harald Wagner

Conventional ground support in accordance with latest state-of-the-art considers proper preparation of geotechnical investigation, structural design, observation during construction and fair risk sharing documents. Depending on the ground, there are different means and methods, reflecting different experiences. The paper is presenting ground support concepts, as mostly used in Europe during the past three decades. It discusses the use of anchors as well as the use of steel arches respectively combinations. It also discusses different applications of plain shotcrete, respectively fibre reinforced shotcrete. As excavation sequence is a major input to create the ground arch, the paper discusses also criteria to create closed ring conditions. Finally deformation criteria will be presented with case histories in order to control stability of the structure.

Jan 1, 2001

By Derek Ettie

"In the Hydrometallurgical processes, the presence of the so-called "crud" is a constant challenge in solvent extraction. Crud is a stable emulsion which forms along the interface between the aqueous and organic phase. The spread is influenced by the following parameters: first, wind blows the dust and impurities into the open sedimentation tanks. Second, the undissolved solids such as sand transported in the PLS causing problems in conjunction with incorrect agitator design.The crud fraction can decisively impact the efficiency of the hydrometallurgical extraction because the phase interface can constitute a large fraction and the sedimentation tanks cannot react flexibly to it. In the downstream process of the series-connected sedimentation tanks, they are thus all contaminated with crud. At the same time, the necessary mass transport is significantly impeded at the phase boundary between organic phase and aqueous phase due to the crud formation.The transfer of the organic phase into the electrolysis cell can result in a "burnout" of the cathode. The carryover of this electrolyte into the extraction can cause problems with the pH regulation. The carry-over of the organic components into the raffinate also leads to contamination of the leaching circuit. The continuous treatment of the crud with a 3-phase decanter centrifuge is extremely effective in combating this problem. This technology splits all three phases from each other and they are consequently continuously separated. All subsequent process steps exhibit a stable, uniform effectiveness. The main advantage for the customer is that fluctuations in the process are eliminated and the organic phase can be recirculated back to the extraction. The recycling of the solvent alone justifies the investment in less than 6 months as examples from South Africa and Chile show.To operate solvent recovery in daily operation fully automated online at the optimum limit, the decanter centrifuge is equipped with a concentration-dependent pond adjustment called DControl® by this means, we can guarantee our customers the maximum possible solvent recovery and minimize the solvent costs in this process step. This system is presented in detail in this paper."

Jan 1, 2014

By H. C. Counsell, R. Webber

"The mill at Denison Mines' Elliot Lake Operations started up in 1957, with a capacity of 6,000 tons per day. Over the years various plant modifications expanded th.is to 7 500 tons per day. In 1976, management decided to carry out a major expansion of the milling capacity, and during 1980 the grinding capacity was increased to 15,000 tons per day.The original comminution system consisted of a conventional crushing plant feeding minus S/s-inch material to rod and pebble mills, in closed circuit with mechanical classifiers. The key decision that had to be made was whether the expansion should include conventional or autogenous grinding flow sheets.During 1977, extensive pilot plant studies at Lakefield Research showed that two-stage semi-autogenous grinding, with some steel media in the primary mill and with pebble media in the second stage, produced stable grinding conditions. This type of circuit was selected by Denison for the expansion, and went into production in 1980. Primary millThe flow sheet of the semi-autogenous grinding circuit is shown in Figure 1. The primary grinding mill is a Koppers 28 foot by 10 foot mill, driven by a 4,000 h.p. synchronous motor. It is fed with a minus 8-inch run-of-mine ore, and 4-inch grinding balls are added as supplementary grinding media. There are two Koppers 15.5 foot by 22 foot secondary pebble mills, driven with 1500 h.p. synchronous motors. Each grinding stage operates in closed circuit with cyclones, and the primary cyclone overflow is the feed to the secondary mills. The circulating load in the primary stage can be controlled by adjusting the cyclone apexes."

Jan 1, 1984

SOME notes on the works of the Electrolytic Refining and Smelting Company of Australia will no doubt be of interest to members of the Institute, more especially as much of the work is new to Australasia. As many of the members who may read this paper have not been in a position to visit works of this kind, and are consequently not thoroughly acquainted with all the operations carried on, the author has taken the liberty, in some cases, to enter into explanation which would otherwise be unnecessary. The works are situated at Port Kembla (New South Wales), about fifty miles south of Sydney, and are approachable both by rail and water. The Government has recently built a low-level jetty upwards of five hundred feet long, and intends installing at an early date an electrically operated portable crane to facilitate the handling of material to and from the boats. This will mean: a considerable reduction in the length of time that boats are laid up at the jetty. There are also under construction two breakwaters, which, when complete, will materially assist shipping operation...

Jan 1, 1910

THE flotation plant at Mount Lyell was erected, primarily, for the treatment of ore from the Lyell Comstock mine. These workings are situated over a mile in a direct line north of the North Mount Lyell mine, and are connected with the Reduction Work at Queenstown by a 2-ft. gauge steel tramway via the Queen River valley a distance of 7 miles. The property was purchased from the Mount Lyell Comstock Copper Co. After the disastrous fire in the North Mount Lyell mine in October, 1912, steps were immediately taken to make Lyell Comstock ore available for treatment, in order to relieve distress caused by any prolonged stoppage of work, and subsequently 13,032 tons of ore, averaging 3.38 %copper, 0.28 oz. silver, and 0.034 oz. gold; were smelted. When operations were resumed at the North Mount Lyell mine, it was evident that there was no economic advantage in smelting Lyell Comstock ore as compared with the higher value North Mount Lyell ore, which was also a better flux for the Mount Lyell pyrites, and that the future of the Lyell Comstock ore depended upon cheap mining and successful concentration of the ore. Therefore, extensive trenching and diamond-drilling was carried out, and a sufficiently large quantity of ore proved available for cheap extraction by open-cut methods. At the same time bulk tests by flotation were carried out at the Minerals Separation testing plant in Melbourne on different classes of ore from the Mount Lyell Comstock mine proper, followed by laboratory tests at Queenstown on all classes of ore available. All these tests demonstrated that the ore was amenable to the process, provided that it was ground finely enough. Plant erection was delayed by the general dislocation of business at the outbreak of war, but finally it became...

Jan 1, 1920

By Michael J. Jorgensen, Pranathi B. Aedla, N. K. Kittusamy

Risk factors associated with the development of muscu­loskeletal discomfort and disorders during the operation of heavy mobile equipment include whole-body vibration and awkward and sustained joint postures of the shoulders, neck, and trunk. Cab design may influence awkward postures of the joints, and task duration may influence duration of exposure to awkward and static postures and whole-body vibration. To reduce exposure to risk factors related to the interface between cab design and task, it may be necessary for manufacturers to address cab design. This study assessed the repeatability of a cab design checklist developed to evaluate various design characteristics that can influence exposure to risk factors for musculoskeletal discomfort. The ability of the cab design checklist to identify posture-related deficiencies of design was also assessed. The checklist was used by two administrators across 10 pieces of heavy construction equipment. Video analysis was performed to quantify postures of the neck, shoulder, and trunk; correlation analysis was used to determine whether specific questions from the checklist were associated with the identification of awkward postures. The repeatability assessment resulted in kappa coefficients ranging from 0.52 to 1.0 (good-to-excellent reproducibility) across each piece of equipment, and an overall kappa coefficient of 0.77 (excellent reproducibility) when considering all equipment together. Results from the correlation analysis showed that shoulder flexion posture was correlated with scores from the cab design checklist. However, results of the cab design checklist were not significantly correlated with shoulder abduction or awkward postures of the neck and trunk. Results suggest that the cab design checklist may be useful for identifying cab design characteristics that need further improvement and for identifying design characteristics that increase shoulder flexion. The strength of the repeatability assessment suggests that outcomes of the cab design checklist administered by different individuals may be consistent, independent of the type of equipment being assessed.

The 1963 Lignite Symposium was held on the University of North Dakota campus, Grand Forks, N. Dak., April 30-May 1, 1963, under the cosponsorship of the University of North Dakota and the Bureau of Mines. This symposium, the third in a series, had as a general objective the dissemination of information concerning advances in technology and utilization of solid fuels, with emphasis on lignitic coals. Approximately 150 representatives of industry, government, and educational institutions from 21 states and 3 Canadian provinces were present at the symposium. Those attending were welcomed by Marling J. Ankeny, Director of the Bureau of Mines, representing the Bureau, and Dean T. H. Clifford, Vice President of the University, representing the University.

Jan 1, 1964

The 1963 Lignite Symposium was held on the University of North Dakota campus, Grand Forks, N. Dak., April 30-May 1, 1963, under the cosponsorship of the University of North Dakota and the Bureau of Mines. This symposium, the third in a series, had as a general objective the dissemination of information concerning advances in technology and utilization of solid fuels, with emphasis on lignitic coals. Approximately 150 representatives of industry, government, and educational institutions from 21 states and 3 Canadian provinces were present at the symposium. Those attending were welcomed by Marling J. Ankeny, Director of the Bureau of Mines, representing the Bureau, and Dean T. H. Clifford, Vice President of the University, representing the University.

Jan 1, 1964

By Joan T. May

The Bureau of Mines conducted laboratory tests to evaluate the production of high-purity H3P04 by HCl digestion and solvent extraction. Both batch and bench-scale continuous tests were made. Western phosphate rock concentrates were acidulated with HCI, and the digestion liquors were processed by solvent extraction. Phosphoric acid was extracted with isoamyl alcohol and recovered from the organic extract by contact with an NH4F solution. This solution was fractionally distilled to yield high-purity H3P04. The raffinate from solvent extraction was treated with lime to precipitate CaF2, which was subjected to steam pyrolysis to generate HF. This method was successful in recovering 95 pet of the phosphate and 80 pct of the fluoride contained in the concentrates.

Jan 1, 1976

By D. M. Walters

To achieve safe and healthy working conditions in shaft sinking operations, ventilation, and where necessary cooling, must be provided. These requirements are considered for sinking vertical, sub-vertical and decline shafts. Regulatory requirements, determining air volumes and amount of cooling required, the various ventilation methods used such as force, exhaust, twin columns, air reversal using four gate systems and the equipment required to achieve this, are discussed. Consideration is also given to the sinking of single and twin declines using diesel equipment, calculating the air volumes required to dilute pollutants and the various methods for achieving this. Also discussed is the importance of having early ventilation design input to the overall design of the mine. In many cases ventilation can be the prime determinant for the size and configuration of the shafts or declines that have to be sunk.

Jan 1, 2009

By Joshua Hoffman, Braden Lusk, John Rathbun

A Flyrock Prevention Taskforce was established in Kentucky with the support of Kentucky's Department of Natural Resources, Kentucky's Explosives Industry, and the University of Kentucky. This paper presents the initial work of the Flyrock Prevention Taskforce towards its missions of identifying the root causes of flyrock incidents based on the analysis of previous events, and tracking the progress of flyrock elimination in the future. Work identifying root causes of flyrock events is presented through the development of a database which manages information about the blasts which caused flyrock. This data includes: blasting and seismograph records, drill logs, videos of the event when available, company notes/incident reports, and any additional information regarding probable cause. Work tracking the progression of flyrock elimination efforts is presented in this paper through the introduction of a flyrock index. Several metrics are proposed for this index, and are discussed for their appropriateness and shortcomings. In order for these indexes to be valid forms of tracking flyrock incident rates additional records must be kept and reported, such as the annual consumption of explosives by surface coal blasting. Suggestions for record keeping, flyrock investigation practices, and means of tracking flyrock incident rates are proposed in this paper.

Jan 1, 2013