Search Documents

By Fumitaka Tsukihashi

Phase diagrams of the CaO-SiO2-FeOx-MgO, Al2O3 systems arc necessary for the analysis of copper smelting reactions and sintering process of iron ore. The effect of MgO and Al2O3 addition on the liquidus of the phase diagram of the CaO-SiO2-FeOx system at low oxygen partial pressure was observed. The liquid phase area changed bi the addition of MgO and Al2O3 with a changing oxygen partial pressure from 10-8 to 10-3 atm (10-3 to 10 2 Pal at 1573K. The effect of Fe3+ / Fe2+ ratio on the melting mechanism is discussed.

Jan 1, 2003

By D. Mukerjee, Ramen Datta, Sanak Mishra, R. Veeraraghavan, K. L. Rohira

"Recent efforts at Steel Authority of India Limited (SAIL) has led to the successful development of atmospheric and marine corrosion resistant high tensile Thermo Mechanically Treated (TMT) bars with minimum specified yield strength of 50 kg.mm-2. These rebars are increasingly being used for a wide range of end-applications, namely, concrete reinforcement structures, bridges, flyovers, dams etc. Welding is an important processing tool for each of the above applications. In view of the importance of welding, a comprehensive evaluation of the weldability properties has been carried for the two grades of steels using Submerged Metal Arc Welding (SMAW) process; the most popularly used technique of welding of reinforcement bars (re bars).Implant tests were conducted to assess the cold cracking susceptibility of the steels. The static fatigue limit (SFL) value, determined for the atmospheric corrosion resistant (Cu-TMT) rebars under no preheat and no rebalcing conditions was found to be 63.8 kg mm-2, which was significantly higher than the Minimum Specified Yield Strength (MSYS) (50 kg.mm-2). This indicates adequate resistance to hydrogen induced cracking (HIC). On the other hand, the SFL value obtained for the marine corrosion resistant rebars (Cu-Cr TMT) under no preheat, no rebaking conditions was found to be inconsistent. Repeat of the test with fully rebaked electrodes (350°C-2h) resulted in a high SFL value (60.3 kg mm-2)_The rigidity of the structure or restraint influences the susceptibility of the weld joint to cracking. The cracking tendency increases with restraint intensity (K) of an assembly. The critical restraint intensities determined for the two steels were found to be· in excess of 1680 kg/mm.mm, indicating good welding behaviour with the following welding conditions : for Cu-TMT rebars with no preheat and no rebaking and for Cu-Cr TMT rebars with no preheat and fully baked electrodes; that is under low hydrogen levels."

Jan 1, 1998

By Glenn Stevens

After 40 years of operation with the original design, Pan Pacific Copper determined it was necessary to rebuild the Saganoseki Flash Smelting Furnace to continue safe operation. The original design employed a rigid steel frame, which, through hearth growth, led to severe distortion of the frame. Contributing to the continued growth of the hearth were thermal cycles that occurred during the government mandated annual shutdowns. Hatch designed a unique sprung bound, pivoting binding frame to maximize crucible size within the existing furnace footprint, while integrating the PPC designed cooling jackets. The bound system maintains tight brick joints, while the new conductive hearth design with integrated bottom cooling produces a protective freeze layer to accommodate higher furnace throughput. Minimization of furnace downtime for the rebuild was achieved through effective construction planning, highly trained contractors, and through an efficient start-up and ramp-up to full production.

By James Vaughan

Australia is a major miner of ore that requires hydrometallurgical processing. According to the 2016 US Geological Survey Minerals Commodities Summaries, the country is 1st for aluminium (bauxite) and lithium, 2nd for gold, zinc and cobalt, 4th for nickel and silver, and 6th for copper mining, not to mention its wealth in coal and iron ore. In this paper, examples of recent Australian hydrometallurgical activities are summarised. Then, selected research projects from the University of Queensland hydrometallurgy research group are profiled. The projects profiled are related to fundamental aspects of processing bauxite with organics and reactive silica as well as the development of a synergistic hydro- and pyrometallurgical process for copper. The process context and motivation for the research is introduced, key results are highlighted with the associated relevant references.

By Y. Ono

In lightweight metal processing such as aluminum (AI) and magnesium (Mg), metal cleanliness is a crucial process parameter for refining, part manufacturing and recycling in order to obtain high quality parts and products. In this paper, techniques for cleanliness evaluation of molten AI and Mg using ultrasonic probes with clad steel buffer rods having high signal-to-noise ratio (SNR) are presented. Due to the high SNR of the ultrasonic probes used, backscattered ultrasonic signals from inclusions, which may be oxide films and/or particles, in molten Mg and those from silicon carbide particles, having an average size of 50f.Ull, added in molten AI are successfully detected with reflection configurations of pulse-echo and/or pitch-catch modes at an ultrasonic frequency of 10 MHz. In addition, relative cleanliness evaluation of molten Al and Mg is demonstrated. In order to establish the procedure and to investigate the optimum system configurations for cleanliness evaluation of molten metals, particle flow simulation system using water and polyvinyl chloride (PVC) particles has been constructed. Counting the number and measuring the size distribution of the PVC particles, having an average diameter of 128um, suspended in water with the PVC volume concentrations of 5ppm and 10ppm are performed with ultrasonic pitch-catch mode. The counted numbers of particles by the presented method and system have good agreement with the calculated results with a count error of less than 10% or two counts. Based on the results obtained with water simulation experiments, the prototype system for cleanliness evaluation of molten Mg by counting and sizing inclusions has been developed. Keywords: Ultrasound, Clad buffer rod, Molten metal, Aluminum, Magnesium, Inclusion detection, Cleanliness measurement, Counting, Sizing

Jan 1, 2003

By A. A. Bustos

A model was developed to simulate the blow-by-blow operation of the converting process. From the weights, compositions and temperatures of all converter feeds the model calculates the composition and tonnage of both converter matte and slag as well as bath temperature at the end of each blow. The development of the model and its application to the converter aisle operation are described. There is good agreement between model predictions and observed results. At the present time the model is being used to investigate different converting schemes and their effect on pay metal recoveries, slag chemistry and temperature of the bath. Future work involves the use of the simulation model as a process control tool for the converting operation.

Jan 1, 1988

By Robert C. Laudon

Spectral reflectance data for 335 minerals, including 228 minimum-maximum combinations for anisotropic minerals giving a total of 563 data sets, have been collected from the literature and combined into a single database. Quantitative color values for x, y, Y, Ad , and Pe referred to ICI standard i11uminant C have been calculated from the spectral reflectance data and are included in the database. The programs plot spectral reflectance curves together with all quantitative color data for each mineral in the database. The plots and data can be directed to a dot-matrix printer such that a databook of quantitative color and spectral reflectance having one mineral per page can be generated for the ore microscopy laboratory. In addition, by sorting the database and grouping the minerals, groups or individual minerals can be plotted on the chromaticity diagram, and this plot can also be sent to a dot-matrix printer. The programs are written in compiled BASICA for an IBM-PC with graphics capabilities and at least 128KB random access memory (RAM). The databases are accessible either through the BASIC programs or through any commercial database system capable of loading and writing to an ASCII format sequential file. The programs and database are available by sending a blank diskette and self addressed, stamped envelope to the authors.

Jan 1, 1987

By Hojat Naderi

In this research assisted leaching of chalcopyrite using sodium peroxodisulfate was studied. Electrochemical techniques such as Tafel analysis and electrochemical impedance spectroscopy (EIS) were used to investigate the surface reactions of a chalcopyrite electrode in the presence and absence of Na2S2O8. According to the results, addition of sodium peroxodisulfate increases the current exchange of the corrosion process and prevents the formation of a passive layer on the surface of the electrode. EIS tests show the trans-passive dissolution of the passive layer on the chalcopyrite electrode in presence of Na2S2O8. Equivalent electrochemical circuits were modeled for Na2S2O8-free and -containing solutions and the model parameters were compared to determine the effect of S2O8 2− on chalcopyrite dissolution. Copper dissolution from pure chalcopyrite mineral and chalcopyrite concentrate was carried out using 15 g/L sulfuric acid solution with and without Na2S2O8. Simultaneous presence of 10 g/L ferric ion and 40 g/L peroxodisulfate salt results in about 40 and 18% of Cu extraction from chalcopyrite concentrate and pure chalcopyrite mineral, after 96 h, respectively.

By A. Mezei

Samples of cobalt and bismuth concentrates produced from the NICO deposit in Northwest Territories were subjected to a comprehensive metallurgical testwork consisting of: pressure oxidation, ferric chloride leach and carbon in leach, to recover the cobalt, bismuth and gold, respectively. A specific testwork program was designed to allow for the optimization of process parameters under multiple restrictive criteria. The overall objective was to establish leaching sequences that could produce acceptable recoveries while generating environmentally disposable residues as well as solutions suitable for further processing. The recoveries for the leaching stage, under the optimum conditions, were 97% for cobalt and 95% for gold, in the case of the cobalt concentrate. The bismuth concentrate produced recoveries of 99% for bismuth, 99% for cobalt and 97% for gold, respectively

Jan 1, 1999

By I. Gaballah

The kinetics of oxychlorination of pure CI-2O3 with C12+02 gas mixtures is studied by ThermoGravimetric Analysis (TGA) in non and isothermal conditions up to 1000 °C. The reaction of Cr2O3 with C12+O2 chlorination gas mixtures starts at about 550 °C and the reaction product is CrO2Cl2. The oxychlorination rate of Cr2O3 is almost proportional to the chlorine partial pressure and to the fourth root of the oxygen partial pressure in the chlorinating gas mixtures. At 800 °C, the maximum chlorination rate is obtained using a gas mixture having a C12/O2 ratio equal to 4. The apparent activation energy of the oxychlorination reaction of Cr2O3 is 87 and 46 kJ/mol at temperatures lower and higher than 650 °C, respectively. By varying the chlorine and the oxygen partial pressures of the oxychlorinating gas mixtures at temperatures higher than 550 °C, it is possible to extract selectively the chromium chlorinated compounds from the chromium bearing materials. a. Laboratoire Environnemem et Minéralurgie, BP 40, 54501 Vandceuvre, France, b. École Nationale Supérieure de Géologie, Rue du Doyen Marcel Rouhault, 54501 Vandoeuvre Cedex, France, c. Centre National de la Recherche Scientifique, 3 rue Michel - Ange, 75794 Paris Cedex, France, d. Insritut National Polytechnigne do Lorraine, Rue de la Font de Haye. 54501 Vandceuvre Cedex, France.

Jan 1, 1997

By W. S. Kirk

World cobalt production in 1987 was estimated to be about 26,600 metric tons (MT) of which Market Economy Country (MEC) production was estimated to be about 22,000 MT. Zaire and Zambia produce about 80 percent of the primary cobalt produced among Market Economy Countries (MEC). Production cutbacks. lowering cobalt grades and mining curtailments in Finland and Zambia in 1987, resulted in lower production than that of 1986. The trend is expected to continue through 1988. Cobalt production from Canadian ores and from Botswana is expected to increase significantly in 1988 as a result of increased nickel production. MEC production in 1988 is estimated to be 22,100 MT, only slightly higher than that of 1987. There are currently no primary cobalt mines. Virtually all cobalt is recovered as a byproduct of copper and/or nickel mining. Zaire, which produces cobalt as a byproduct of copper, is the worlds largest cobalt producer, with over 50 percent of total estimated world cobalt production and nearly 65 percent of MEC production. Zambia follows with about 14 percent and 17 percent, respectively. Zambia's cobalt production also results from copper production.

Jan 1, 1988

By C. Kathryn Sole

The close proximity of cobalt and nickel on the Periodic Table and their frequent occurrence together in nature means that their separation in primary hydrometallurgical flowsheets is not only often necessary, but requires the use of innovative chemistry to achieve high selectivity. Today, increasingly stringent demands for the high-purity cobalt and nickel salts required for battery applications in consumer electronics, electric vehicles, and solar applications are again challenging the state of the art. The evolution of cobalt–nickel separations is traced from the basic precipitation technologies employed in 1960s, through commissioning of the first cobalt solvent-extraction plant in South Africa in 1974, to the commercialisation of organophosphinic-acid extractants (which provided a step-change improvement in selectivity) and their eventual widespread use in the 1980s and ’90s. This was followed later by their sulphur analogue, which enabled different possibilities for laterite processing in the new millennium. Separations in chloride media, which take advantage of the different speciation chemistries, and nickel extraction by oximes in ammoniacal systems are also discussed. More recently, chelating and solvent-impregnated resins have added further dimensions to the possibilities for flowsheet design and enabled higher purity products to be attained from both primary and secondary sources. Selected case studies and flowsheets are described.

By lonkion M. Font

Due to the known disadvantages of the use of iron silicate slag in the nickel converting stage, i.e., high metal losses, high magnetite content, and low fixation of impurities in the slag, the development of the new proposed "ferrous calcium silicate slag" for smelting and converting processes of nickel is very promising. Hence, considering the successful experimental results of using CaO base slag for the nickel smelting process, a study based on a detailed comparison for the phase equilibrium, and the minor elements distribution between the NilS2-FeS matte with either FeOx-CaO or FeOx-Si02 base slag was investigated. The main results are summarized as: no difference in the nickel losses between both slags was found at high nickel content in the matte, and the fractional distribution analysis for arsenic and antimony pointed out their preferential fixation in the calcium ferrite slag rather than in the iron silicate slag. Considering the energy and pollution issues, the technical feasibility of using calcium ferrite slag in a converting process of the Bessemer matte will have a prominent future for the nickel industry.

Jan 1, 2003

By Robert L. Stephens

"It can be argued that one of the most important property of any material is cost, since this property detennines the applications for which a material can be considered. Despite growing demand and production for commodity metals such as copper, nickel, zinc, lead, and tin, the cost of these metals has been steadily decreasing in real terms. The only way that metal miners and producers can remain financially viable in the long term is by continuing to lower their cost curve through the implementation of new metals production technologies. This paper reviews technological developments in the production of copper, nickel, zinc, lead, and tin that have or threaten to redefine the cost curves for these metals.DisclaimerThe opinions expressed in this paper the author's, and are not necessarily those held by the author's employer, Cominco Ltd.IntroductionThis meeting will discuss many novel technologies and processes for producing metals and materials with specific properties that will enhance the applications ranges for the material or will allow entirely new applications to be developed. However, in every real-world case, the cost of the new material or process is an important property that determines which applications the material or process can be used in. Other properties that are important depend on the applications.A recent press report (1) discussing the potential replacement of aluminum radiators with copper radiators in pickup trucks and sport utility vehicles provides an interesting example to reinforce the importance of cost in materials selection. In this case, the displacement of aluminum by copper is being considered because of the more favorable heat dissipation characteristics of copper. Heat dissipation has become more important due to the development of hotter-burning V-8 and V-6 engines. For this application, engineers also consider cost, weight, size, durability, and manufacturing process. The report stated that the development by the International Copper Association (ICA) of the ""CuproBraze"" manufacturing process for heat transfer products was an important development. This technology produces 845 radiators that weigh less, are more uniform in quality, and are potentially more compact. They are also expected to cost less in high production quantities than copper units produced in the past, last three to four times longer than soldered copper radiators, and the process also eliminates the use of lead solder from the manufacturing process."

Jan 1, 2000

By David B. George

Kennecott recently completed an $880 million modernization and expansion of its smelter and refinery to process all concentrates from the Bingham Canyon mine. This is the first application of Kennecott-Outokumpu Flash Converting. Molten material movement by overhead cranes is eliminated and high levels of oxygen enrichment result in very low process gas volumes and exceptionally control of sulfur oxide emissions. All existing in-plant hygiene, safety, and environmental regulations will be met and the smelter is positioned for anticipated more stringent future regulations. Sulfur capture is 99.9 percent resulting in sulfur dioxide emissions less than the 112 kg/hr Air Permit limit, making the smelter the cleanest in the world.

Jan 1, 1996

By Alan P. Prosser

The heap leaching of gold ores by cyanide solution was simulated by computer program. The program uses only basic m1neralogical and chemical data; no process testwork data, such as column leach results, are required. The simulation can be used to forecast the consequences of various changes before and during the testwork, design and operation stages of a particular ore-process system. Also, data about the state of different parts of the heap at various times help create an understanding of what is happening. The effects of mineralogical and process variables on the overall performance of the ?heap leaching process are illustrated. Comparisons are made to column leach tests and production data. The potential of the simulation strategy is discussed for making better use of operating experience and for suggesting specific research objectives. It has become clear that more attention should be paid to other metals that dissolve in the solution.

Jan 1, 1989

By Fumito Tanaka

The Mitsubishi process is the sole pyrometallurgical process for the continuous production of blister copper from copper concentrates and has been successfully operated around the world. The development of calcium ferrite slag (CaO-FeOx-Cu20), the so-called "C-slag", has enabled continuous converting from matte to blister copper in the commercial scale operations. Commercial interests in the slag led to many papers over the CaO-FeOx slag. However, CU2O- bearing slag has not been studied well due to experimental difficulties. The authors have quantified the thermodynamic properties ofthe CaO-FeOx-Cu2O system. The results have been utilized to analyze various issues related to the converting furnace, such as the magnetite precipitation from the slag or from blister copper and to develop better controlling criteria for the continuous converting operation.

Jan 1, 2003

By Rauno Peippo

Horizontal Waste Heat Boiler (WHB), today's proven and dominating technology for copper smelter gas cooling, has been utilized by the industry for over half a century. During this time development has taken place in geometry, flow characteristics, cleaning technology and design details. This development has been driven by improved understanding of the specific process requirements, gained both by wide experience and by utilizing new emerging design tools, like computer flow modeling. It had to wait till mid 90's to unite effective and proven Spring Hammer cleaning technology and the process benefits gained by gas guiding vanes or baffle wall in the copper smelter WHB design. The new design has demonstrated improvement in gas cooling efficiency and the process conditions down stream in form of less dust sticking problems in the boiler and precipitators. Reduced weak acid production has also been reported as a result of the design. The theoretical aspects, computer flow modeling results and actual benefits measured in old smelting line modernization are discussed. Experience £tom modernization projects such as Phelps Dodge, Atlantic Copper, Mexicana de Cobre, and Nippon Mining, Saganoseki, are discussed. In mechanical design there has been development resulting improved gas tightness with less corrosion and better control of dust sulfation. An essential improvement is the integration of the boiler hopper and dust removing conveyor. Having no steel plate casings in the hopper and conveyor section but using of boiler tube membrane instead eliminates thermal expansion differences. The dust conveyor will be effectively cooled against hot dust lumps falling down while the acid dew point corrosion is prevented in the cooler sections of the hopper. Conceptual features are presented of a new generation Copper Flash Smelter WHB presently under construction at Boliden Mineral, Skelleftehamn, Sweden, where the latest development and innovations are adopted.

Jan 1, 1999

By Roger L. Williams

The Zinc Corporation of America Monaca smelter continues to use the St. Joe-developed electrothermic process for producing zinc metal and zinc oxide. As we enter the 1990s, the electrothermic process flexibility permits treatment of larger quantities? and lower-grade zinc-bearing recycle materials. A new sinter plant having one large sinter machine will increase sinter feed production required to meet our capacity target of 150,000 tons per year.

Jan 1, 1990

By B. Mishra

The major waste product of the alkaline extraction of alumina from bauxite [Bayer Process] is known as red-mud. Approximately, a ton of red-mud is produced for every two tons of bauxite that is mined. The red-mud produced from Jamaican bauxite is rich in hematite, alumina and titanium oxide. It has been shown that over 90 wt. pct. alumina can be recovered from red-mud by soda-ash sintering and caustic leaching. Hematite can be carbothermically reduced with a degree of metallization of over 94 pct. At this stage, the product could be charged through the tuyeres in an iron blast furnace or smelted to produce pig iron. The mineralogical characteristics of the reduced product are not amenable to magnetic separation for iron recovery. The problems associated with the use of reduced red-mud as an alternative to direct-reduced iron [DRI] has also been discussed. Special attention has been paid to lower the alkali content of the reduced material. If smelted, the concentration of titanium oxide in the slag will be significantly high justifying its recovery by an acid-leach process. This paper describes the successful efforts of iron and alumina recovery.

Jan 1, 2000