Search Documents

By A. Patti, S. Reutzel, D. M. Herlach, L. Ratke, I. Egry

Cu-Co shows a metastable miscibility gap in the region of the undercooled melt. Undercooling of the melt below the binodal leads to separation of the melt into a Co-rich LI-phase and a Curich L2-phase. Experimentally, undercooling into the metastable miscibility gap is realised by means of electromagnetic levitation (EML), processing in drop tube (DT) and by melt flux embedding. As undercooling is large in these experiments, the velocity of the solidification front is high and the microstructure is frozen in instantaneously. Samples have been undercooled and solidified in the TEMPUS-facility (container less electromagnetic processing under weightlessness) during parabolic flight under reduced gravity conditions. Microstructures of solidified samples have been analysed and compared to those processed under gravitational conditions. The influence of convection on phase growth is much lower in reduced gravity. The microstructure shows spherical droplets of the minority phase, statistically dispersed in the majority phase.

Jan 1, 2004

By R. D. Irwin, W. M. Mullins, E. A. Medina

"Various stability criteria are introduced and thermo-kinetic models for metallurgical processes are used as concrete examples for evaluation. Kinetic criteria for the process of dynamic recrystallization are proposed. These criteria are compared to the non-equilibrium thermodynamic approaches discussed in the literature. The application of macroscopic stability criteria to materials processing is then discussed.IntroductionThe mechanical behavior of metals at elevated temperature is very well predicted by any of several empirical constitutive relations. Typical is the power-law (or Swift's) form,Equationwhere r-is the stress, y is the strain and m, n , t0, y0 and Q are material constants. This form has been used with some success in the metals processing area [1]. In general, though, all of the empirical constitutive equations are static, failing to account for any dynamical properties of the system they seek to describe.The physics of warm deformation is qualitatively well understood. An example is power-law creep, where the dominant mechanism is assumed to be lattice diffusion limited climb of dislocations, which allows the strain-rate to be determined by the applied stress through"

Jan 1, 1997

By QinGuo, Shenghui Guo, Lei Li, Jinhui Peng, Linqing Dai, Libo Zhang

The ferrous removal process after carbothermic reduction of chromite fines with microwave heating combined with leaching was investigated. Under the following conditions: Reaction temperature: 1150 , Reaction time : 40min, Semi coke ratio: 12% , the iron content of the reduction product : 13.05% . Metallization achieved was 52.7%. Reduced chromite was leached with 8% of H2SO4 and FeCl3 aqueous solution. The results show that: the recovery rate of chromium can reach 88.06%, the mass ratio of chromium to iron is 3.5:1 for leaching 30 minutes with 8% of H2SO4; the recovery rate of chromium can reach 88.91%, the mass ratio of chromium and iron is 2.56:1 for leaching 4h at room temperature with FeCl3 aqueous solution (100g/L). The leaching time of latter is longer but can realize the circulation effectively and reduce the waste liquid processing problem.1

Jan 1, 2016

By Michael B. Tessieri

With the increasing environmental demands and higher fuel efficiency standards on auto manufacturers, the use of aluminum in automotive applications is expected to show significant growth for the balance of this decade. Cast and wrought aluminum usage is reviewed by auto part, and alloy family for the year 2000 automobile. The analysis addresses the effect of this increased volume on the recycling infrastructure and identifies issues and opportunities, which will face the recycling industry.

Jan 1, 1995

By Young-Dae Kim, Dong-Sic Kim, Jong-Jin Pak, Kyung-Hyo Do

"Sulfur is one of the most harmful elements in stainless steel (SIS) products and the specification of sulfur content is getting more severe for high grade SIS. In order to accurately control the desulfurization reaction in high chromium containing SIS melts, it is important to know the thermodynamic interaction between chromium and sulfur in Fe-Cr melts over a wide range of chromium content. In this study, the equilibrium sulfur distribution, Ls, between a Ca0-Alz03 slag and Fe-Cr-C,.,-S melts were measured under CO atmosphere in the temperature range of 1823-1923 K. The specific effect of chromium on the activity coefficient of sulfur in the melts was determined with the consideration of carbon effect on sulfur. A separate experiment was carried to determine. Ls between a slag and FeCr- S melts (Cr: 0-30 mass%) at 1873K to check the validity of the thermodynamic parameter determined in the present study.IntroductionFerritic stainless steels containing chromium (Cr) up to 30 mass% have been developed for a good corrosion resistance and a high formability to replace austenitic SIS. Especially, Sulfur (S) causes a reduction of high-temperature strength and the hydrogen induced cracking (HlC) in stainless steel for line pipes. [l]Many studies on the desulfurization of hot metal and liquid steel have been carried out for several decades and they used HzS-H2 gas equilibrium technique for measuring the effects of many alloying elements on the activity coefficient of S in liquid iron. However, the study on desulfurization of Fe-Cr melts was very scarce.[2] In order to accurately control the desulfurization reaction of high Cr stainless steel, it is essential to know the thermodynamic relation between Cr and S in Fe-Cr melt over a wide range of Cr content and temperature.In the present study, the thermodynamic interaction between Cr and S in liquid iron was determined by measuring the equilibrium distribution ratios of S between Fe-Cr-C,.1-S melts containing a wide range of Cr up to 30 mass% and a 55 mass%Ca0-45 mass%Alz03 slag of which the sulfide capacity was pre-determined using Fe-C,a1-S melts in the temperature range of 1823-1923 K. The validity of thermodynamic parameter determined in the present study was checked by measuring the S distribution between a Ca0-Alz03-Mg0 slag of known sulfide capacity and liquid Fe-Cr-S alloy at 1873 K. Using Wagner's formalism, the results of experiment were thermodynamically considered to determine the effect of a specific concentration of Cr on the activity coefficient of S in liquid iron."

Jan 1, 2014

By Onuralp Yiicel, Ozlem Okur, Murat Alkan

"In this study, Co-Cr-Mo alloys were produced using a mixture of Co304, Cr203 and Mo03 powders with Al powders by a Self-propagating high temperature synthesis process. SHS is a process of material synthesis that has revealed a number of reactants combinations capable of much higher energy release than conventional explosives. Al203 is added to the mixture to decrease the adiabatic temperature of the system. The thermodynamic simulations and the calculations of adiabatic temperature were examined with FactSage 6.2. In the SHS experiments, different Co304/ Cr203/Mo03 ratios were examined, and their effects on the metal recovery and alloy compositions were carried out. The samples were characterized by using chemical analysis, XRD, XRF and SEM/EDS techniques.IntroductionSelf Propagating High Temperature Synthesis (SHS) has significant advantages compared to the high technology furnace applications, such as very short processing time, simple operation, low energy requirement and low cost [l, 2]. In a SHS process, the ignition starts the combustion and propagates throughout the reactant mixture yielding the desired product. However, the disadvantages of the process such as inhomogeneous or unreacted products due to undesirable reaction rates needs to be overcome by changing some parameters such as ignition temperature, particle size, additive, atmosphere etc. [3, 4]. This work aims to establish a scientific and engineering background in the production of some cast Co-Cr-Mo master alloys via SHS (Self Propagating High Temperature Synthesis) metallurgy which is attractive process technique regarding fast and low-cost production ability of cast alloys."

Jan 1, 2013

By Wenjun Duan, Zongliang Zuo, Qingbo Yu, Qin Qin, Junxiang Liu

Moving bed has been widely used in the field of heat and mass transfer and reaction between solid particles and gas. In order to enhance the heat exchange coefficient, there will be tube banks inserted in the moving bed. In the process of drying ammoniates particles or heat recovery from high-temperature particles with moving bed, the particles flow behavior around the tube banks is significant. In this paper, the particles flow behavior around the tube banks is investigated, and all the results can provide guidance for the design and operation of a moving bed.

Jan 1, 2016

By José R. de Tenorio

The aim of the present work was to investigate the reduction process of MnO~FeO-Si02 slags by carbon-saturated liquid iron. The effect of the initial Mn content in the bath was explored. The initial Mn content was in the range of 0 up to 40 wt. %. The MnO content in the slag was kept constant at 40 wt. %. Tests were performed in laboratory apparatus. Samples of slags and bath were taken. In the first 5 minutes, it was observed a very strong reduction of FeO. This first step promoted a MnO-Si02 enrichment of the slag and a formation of CO bubbles, which increases the slag level. The increase ofMn content decreases the MnO reduction rate.

Jan 1, 1996

By D. J. Droppert

This paper describes the precipitation-production of crystalline scorodite (FeAs04.2H20) from arsenic-rich sulphate-based metallurgical solutions at ambient pressure (95°C). Arsenic is precipitated by means of a controlled precipitation technique in which the supersaturation of the solution is carefully controlled. By controlling the supersaturation in the presence of seed material. the formation of amorphous ferric arsenate is prevented. Scorodite is known to be the most stable As(V) compound and is therefore preferred as host mineral for arsenic immobilization. The effect of the following parameters on the preCipitation behaviour and kinetics of scorodite are discussed: Type of base seed concentration initial [As]. sulphate concentration. neutralization rate. seed recycling and method of Fe(ll!) addition to Fe-deficient arsenic solutions.

Jan 1, 1996

By Amy Anderson

The Silica (SME) Technology has been utilized on three separate projects focusing upon the stabilization of mercury-contaminated materials: at the Mother Lode Mine in Oregon, the Sulfur Bank Mercury Mine in California and at a former chloralkali plant in British Columbia. Each of the projects relied primarily on the results collected via EPA Method 1311 TCLP, with additional tests such as SPLP, humidity cell tests and other supporting tests employed as well. Both technical and economic performance of the silica-based technology was evaluated as well as that of competing technologies in some cases. Results established that in each of the three projects an SME chemical dosage rate of 3% chemical by weight of soil/sludge was the optimal ratio required to achieve project treatment objectives, TCLP test results exhibited a reduction in the leachable mercury from the treated materials ranging between 75% and 99% as compared to untreated material, satisfying the technical objectives for each project, Project costs ranged from $l5.00 - $18.26 per metric ton.

Jan 1, 2003

By Guohui Zheng

The ever increasing quantities of solid wastes generated by various industries are at the source of the growing need for proper waste disposal methods. Thermal treatment of combustible wastes is a proven technology which permits the reduction of hazardous material having to be landfilled. However, this method is not universally applicable to waste disposal. For example, the transferal of heavy toxic metals into the thermal remediation products is a major issue of public concern. This paper focuses on the analysis of morphology changes from solid sludge to ash which is a product of the sludge combustion. The morphological parameters analyzed were particle size and external surface. They were determined using Jeol 840 Super Probe. The experiments were conducted in a computer-controlled high-temperature combustion system consisting of the thermogravimetric furnace coupled with Fourier transform infrared spectrometer (TGA-FTIR). Sludge particles were made of complex fibers trapped in the aluminosilicate matrix. At low temperatures, up to 680 K, the solid residue looked similar to the initial sludge. Between 680 K and 1180 K the sludge underwent intensive burning and steadily changed into powdered ash. At the temperature of 1050 K the ash was composed of separate, flat flakes with sizes ranging from 5 to 20 um. At 1470 K the flakes aggregated into large particles. The surface observed at 1670 K was a mixture of mullite crystals. Such structure could result from the solidification of the ash material after its melting. Morphological changes influenced the distribution of metals in the solid residue. For example, Cr was concentrated in small aggregates. Such distribution should allow for recovery of valuable metals from the solid waste residue.

Jan 1, 1996

By Hidenori Okamoto, Katuto Itoh

"Nippon Mining & Metals' Hitachi Refinery refines 40% of the anodes produced at its Saganoseki Smelter & Refinery. Its current annual production stands at 180,000tons.The refinery always endeavors to increase productivity. One of the outcomes of its efforts is an originally developed automatic short-circuit detector used to inspect short-circuits between anode and cathode. The detector is designed to inspect the 56 pairs of anode and cathode in a cell by fluxgate sensors at once. It inspects 564 cells, automatically and un-manned, and gathers data to be put into a computer. The development of the detector led to a reduction of man-power and achieved a detection accuracy superior to that of a hand-held gauss-meter. In addition, statistical and historical processing of the data enabled early detection and early recovery of the cells with poor efficiency.The new system also contributed to raising the refining capacity and reducing the unit steam consumption, because it is possible to inspect even the cells covered with thermal insulation sheets.IntroductionInspection of cells is an important component of the operation management of a tank-house. At the Hitachi Plant, it used to be carried out by two workers who walked on and checked all the cells of its tank-house once a day to find out any short-circuits in the cells, using hand-held gauss-meters. They inspected about 33 thousand pairs of cathodes and anodes a day and removed nodules by hammers. This method had following problems:it needed much manpower.the walk on the cells sometimes deranged electrodes positions.there was radiation-loss connected with the inspection due tothe fact that the workers were obliged to uncover thermal insulation sheets on the cells while inspecting."

Jan 1, 2000

By T. S. Bannos

Section 1417 of the Safe Drinking Water Act Amendments enacted by the O.S. Congress prohibits the use of lead containing solders for potable water systems in new construction or when making repairs. The legislature defines "lead-free" solder as containing less than 0.2% lead. In the development of a new solder it was recognized in addition to the lead free requirement, the alloy should perform as well as the popular 50/50 tin lead solder, both in application and properties. Another objective was to have only nontoxic elements. This led to the development of a 4.0% copper, 0.5% silver and 95.5% tin solder. Review of the merits of other alloy systems and the development of the physical properties along with test data are presented for the lead free tin. rich alloy.

Jan 1, 1990

By Hidefusa Takahara, Koichi Miyake, Dierk Raabe

"Mechanical properties of copper wires were examined. The copper wires containing 5-10 mass % chromium and 1-3 mass % silver were produced through heavily cold deformation. It was expected that the copper wire was easily fractured during cold deformation because of the existence of brittle chromium phase in the alloy. In fact, the copper wire was fractured due to large work hardening, when the true strain [n] exceeded 5. However, the copper wire annealed at 1273K for 6 ks ·in the middle of deformation process could be smoothly drawn to 11=8. After precipitation treatment for silver phase at 473k for 1.8 ks, the wire was able to further drawn to n=8.4. The final deformed wire showed tensile strength higher than 1200MPa.IntroductionDownsizing of electronic devices has led to the demand of finer and higher strength materials for cables. Conventional copper alloys have about 800MPa in ultimate tensile strength. These strength are mainly obtained by precipitation hardening. Nowadays, a process for higher strength wire has been developed, where dual phase copper alloy is used. When it is drawn heavily, the' second phase is elongated along drawing direction and the wire gets high strength due to fiber reinforcement (1). That alloy is so called in-situ formed fiber reinforced ·alloy. Cu-Ag(2), Cu-Nb(3) and Cu-Cr(4) systems are well known as such alloys. It is also well known that chromium is brittle material except single crystal and high purity of chromium. However, Mihara et al. C5l have achieved 1 GPa in ultimate tensile strength in the Cu-Cr-Zr and Cu-Cr-Ti alloys by appropriate thermo-mechanical processing.In this study, the Cu-Cr-Ag systems were investigated: The alloys contained 10 or 5% chromium and 3 or 1 % silver. It was demonstrated that silver precipitated in copper matrix contributed on further hardening."

Jan 1, 2000

By Baozhong Zhao

Laboratory experiments have been conducted on the removal of As, Sb and Bi from molten copper by SF 6 injection. The results showed that the impurities can be removed by SF6 injection in the? sequence of Sb >As >,Bi and the rate of Bi removal is affected significantly by the concentration levels of As and Sb in the copper melt. Analysis of the experimental data indicates that the impurity removal process is under chemical reaction control rather than by mass transfer of impurity through the molten copper phase. On the basis of experimental results, a kinetic model was developed and the order of chemical reaction and the volumetric chemical reaction rate coefficients of impurity removal were determined.

Jan 1, 1996

By Neale R. Neelameggham

"Most chemical process plants and metallurgical production facilities have some sort of cogeneration to minimize process energy costs. Use of Alternative Energy Production from sun and wind power with storage can become an integral part of a process plant utility. This will facilitate reduced fossil fuel usage and help minimize thermal emissions. This will be similar to Pollution Control equipment, which have become an essential part of process plants in the past four decades. Conceptual flow sheets of such Process Utility schemes are presented.IntroductionPower is supplied to industries, commercial and residential users. Over the past decade, Electric Utility companies have made major inroads, in introducing alternative energy resources in an attempt to somewhat reduce fossil fuel use in power generation. Now, on a much larger scale than in the early 1980s, residential users, motivated by government provided tax credits, have started installing alternative energy generators such as roof top wind mills or roof-top photovoltaic generators. This will minimize future energy costs, help control thermal emissions etc. This alternative power generation is typically connected to the existing power grid with two way power metering. However, the use of alternative energy generation has not been seen at large industrial sites yet.Paul Scherer Institute, Switzerland and the NREL laboratories in Colorado, are two of the several institutes which have been developing how solar thermal power can be used to supply the endothermic input energy in chemical and metallurgical processes. The theme of this present symposium addresses the above as well as the energy storage needs for such events to become continuous. This paper emphasizes the concept of how alternate energy can be used in the production of materials on a generic sense wherever there is a need for input energy – beyond endothermic process energy - while addressing how to reduce the thermal and carbon emissions.The alternative energy generation using wind or solar source is discontinuous due to the nature of the energy source. They are not only discontinuous but also variable. This necessitates storage of generated power for close to continuous use with variable loads. C Smith, et al pointed out in 2006, that 'the electric power industry has taken notice of the expansion of wind and its potential' in a summary article on integrating wind generation into utility systems.1 In 2009, the 1000 MW wind generation project in Texas had to be postponed to 2013 for lack of transmission.2 There are only a few large MW solar generation units in the US; the projects being slow mainly from lack of adequate storage and redistribution."

Jan 1, 2010

By Nicholas Zabaras, Deep Samanta

"Solidification of metal aluminum and aluminum alloys is modeled on uneven surfaces characterized by sinusoidal curves. Wavelengths and amplitudes of these sinusoidal surfaces are varied to study their effects on processes like solidification, macro-segregation and inverse segregation. Solidification and macro-segregation are modeled using a slightly modified form of a stabilized finite element method developed recently to model high Rayleigh number solidification and porous media flows. For pure metal solidification, the effect of varying amplitudes and wavelengths is observed in heat transfer, fluid-flow ~nd phase change processes. The relative importance of shrinkage driven flow and solutal convection on the redistribution of solute for an alloy solidifying in a rectangular cavity is compared. The analysis is then extended by modifying one of the surfaces to a sinusoid. In this case the effects of varying amplitudes and wavelengths are studied in heat transfer, fluid flow, phase change, macro-segregation and inverse segregation processes.1 IntroductionTransport phenomenon during solidification of alloys is a major cause ofcasting defects such as segregation, micro-voids, hot tears, porosity, internal and surface cracks. Heat flow across metal and mold surfaces directly affects the phase change process and plays an important role in determining freezing conditions within the metal. In alloys, natural convection and shrinkage play an important role in determining the final solute redistribution, macrosegregation and evolution of solid macromorphology. Surface unevenness plays an important role during the early stages of solidification. It influences the heat transfer rate and fluid flow in the melt, which in turn affect the morphology and shape of the solid-liquid interface. The effect of surface unevenness on solute redistribution is important during solidification of alloys, where solute driven flow in the mushy zone is prominent. Thevik and Mo in [7] and [8] used a one dimensional model for studying surface segregation and macrosegregation in alloys under the influence of exudation and solidification shrinkage. Air-gap formation in their model was expressed through a variable convective heat transfer coefficient at the boundary. Tsai et al. in [3] and [4] have modeled macrosegregation in an aluminum-copper alloy driven by shrinkage and solutal convection. They used a single domain model based on mixture theory and solved the transport equations using finite difference methods. Our aim is to model solidification of aluminum followed by macrosegregation and inverse segregation in aluminum-copper alloys on uneven surfaces by finite element methods. These surfaces are modeled as sinusoids characterized by amplitudes, ?s and wavelengths, As, By varying As and ?s, changes in heat transfer, fluid flow, phase-change and macrosegregation are studied."

Jan 1, 2004

By G. Belardi

The purpose of the study was to check on the level of environmental contamination and to design a project for cleaning up the Abetina Mine area at Piancastagnaio (Grosseto, Italy). Contamination of this area had occurred during the mining and treatment of cinnabar (HgS) over a prolonged period. The aim of the project is to remove the sources of contamination or render them harmless. Mining of the Piancastagnaio deposit started in 1840, mercury metal being extracted from the ore by thermal treatment. Together with Spain, Italy was the first country to produce this metal and was the world leader in this field between 1936 and 1943. Though mercury production in the Monte Amiata region of Tuscany ceased in 1974 the ensuing environmental impact is very evident, taking the form of rusty old mining and processing works, plus waste tips which still contain considerable amount of mercury even after the ore had been subject to thermal extraction treatment. The research which has been conducted included mapping the area to identify the main sources of mercury and arsenic pollution, as well as the level of environmental contamination. Mercury and arsenic values in excess of 16,000 and 150 ppm respectively are encountered in the most highly-contaminated places. The cleanup project has been drawn up on the basis of the field and laboratory investigations. This provides for a combination of remediation measures on the land concerned, as well as in situ inertization of contaminating elements by means of mixtures of chemical compounds such as cyclosiloxanes. Due account has been taken of Italian and EU environmental regulations when establishing the measures for rendering the various polluting element innocuous. 'The efficacy of the inertization techniques has been checked by yield tests in acetic acid and carbon dioxide, reducing the Hg and As contents of the material in the untreated and treated states from maximum values of 7 mgll to minima close to zero.

Jan 1, 1996

By Tuomas Hirsi

The world’s first large scale modular solvent extraction plants have been delivered by Outotec. The first of these is now in operation and has proven that the VSF®X technology can deliver the excellent performance of the Outotec VSF® solvent extraction process. Modular delivery allows site work to be minimized and the manufacturing done in a controlled environment, allowing for serial production manufacturing benefits. Container based delivery was found to be a highly efficient way of utilizing the standardized transportation methods on a global scale. Site work with modular units was found to be efficient and highly predictable. In this paper, we present the first successful Outotec VSF®X deliveries and discuss the benefits of the modular delivery and design compared to the standard solvent extraction installation’s delivery. The process performance of the VSF®X is also discussed with experiences from the first industrial reference presented.

By Mark William Kennedy

Modern metallurgical plants typically have complex flowsheets and operate on a continuous basis. Real time interactions within such processes can be complex and the impacts of streams such as recycles on process efficiency and stability can be highly unexpected prior to actual operation. Current desktop computing power, combined with state-of-the-art flowsheet simulation software like Metsim, allow for thorough analysis of designs to explore the interaction between operating rate, heat and mass balances and in particular the potential negative impact of recycles. Using plant information systems, it is possible to combine real plant data with simple steady state models, using dynamic data exchange links to allow for near real time de-bottlenecking of operations. Accurate analytical results can also be combined with detailed unit operations models to allow for feed-forward model-based-control. This paper will explore some examples of the application of Metsim to real world engineering and plant operational issues.

Jan 1, 2014