Search Documents

By S. K. Kawatra

"A typical steelmaking facility produced 50,000 tons per year of slag in their hot-metal desulfurization process. This slag had a sufficiently high iron content that it could be beneficiated and recycled in a blast furnace, provided that the slag could be agglomerated into pellets suitable for use as blast furnace feed. In this work, beneficiated slag was agglomerated using both a conventional bentonite binder, and a fly-ash-based binder (FBB) that was formulated by the investigators. The FBB consisted of a combination of highcarbon fly ash with calcium hydroxide activator, allowing the FBB to exhibit binding properties when moistened. It was determined that beneficiated slag agglomerated with FBB had superior compressive strengths compared to slag agglomerated with conventional bentonite binder. The FBB is therefore a satisfactory method of binding the agglomerated slag. Since the fly-ash component of the FBB is commonly discarded as waste, this approach also provides a means for utilizing high-carbon fly-ashes that currently have very little commercial value.IntroductionIn 2006 approximately 72.4 million short tons of fly-ash were produce in the United States [1]. The majority of fly-ash which was used that year was consumed concrete, structural fills, and cement. It is also used in road base, aggregate, and other applications. However, 55.2% of the fly-ash produced in 2006 was not utilized and ended up being sent to a landfill. Essentially all of the land filled fly-ash could be a suitable binder for pelletizing desulfurization slag and other steel plant waste oxide materials. Fly-ash based binders (FBB) have been shown in laboratory studies to be suitable for producing iron ore concentrate pellets of equivalent strengths as those bonded with bentonite [2,3,4]. The utilization of highcarbon fly-ash within the market is important for reducing the volume of currently unmarketable and land filled fly-ashes. FBB would be a much cheaper alternative to the current bentonite binder or organic binders used for iron ore concentrate and would help to reduce pellet costs. Currently, transportation more than doubles the final cost of bentonite since it is produced hundreds of miles from the pelletizing plants, while fly-ash is produced from power plants located nearby pellet plants and steel mills. FBB’s also show promise for use in other high volume applications such as foundry sand mold binders."

Jan 1, 2008

By Takahiko Okura

"It is said that the energy and resources crisis will come before long because the lifetime of known deposits of crude oil and common metals such as Pb, Zn, Cu is estimated to be less than 50 years. Establishing the sustainable society by means of resources-recycling has become an absolute necessity.The non-ferrous metals industry in Japan has been involved in the resource- recycling business for many years, along with the introduction and enforcement of various legislations to preserve the environment and natural resources. Including process-linkage during various manufacturing activities, the non-ferrous metals industry, the iron-making and cement industries are treating considerable amounts of recycled materials and wastes, in an environmentally-sound and economic manner.The Mining and Materials Processing Institute of Japan has submitted “The present and issues in Japanese non-ferrous metals and recycling industries.”The topic of the paper is to highlight the actual conditions within the resources-recycling structures and the present issues.IntroductionGlobalization has been changing the world, introducing the spike of energy and metals price. In addition, the preservation of the environment has also been strongly facing the crisis and many people have been aggrieved by both shortage and the increment in the price of the meals.In the world of metals, even though their reserves are coming depleted, the production rates are increasing, and then the industry has to enhance their productivity under stricter environmental regulations. The Japanese industry experimented the same scenario some 40 years ago, facing big pollution problems, but concurred them and enhanced the technology to overcome the more severe regulations. It will be fruitful to present the current situation in the Japanese industry for the world. The present issues are also presented."

Jan 1, 2008

By Sharon L. Eyer

"FTIR spectroscopy is employed to define mineable ore deposits based on exploration samples. The RAMBO (Robotic Assessment of Mineable Bauxite Ore) technology is operating successfully at an alumina refinery in K winana, Australia, for assessment of a number of critical ore attributes including available alumina, extractable organic carbon and total iron. Classical methods of analyses for these properties require laboratory-scale digestion of alumina ore (bauxite) or XRF analyses.Multivariate calibration is used in the RAMBO system to generate robust mathematical models that are able to estimate classical data from FTIR spectral data. Furthermore the models can highlight regions of ore that are relatively unusual. Unusual ore may be investigated for potential impacts on refinery processes well in advance of mining.The components of the technology are described and some results for an example application (bauxite) are presented. Challenges and difficulties are discussed. The potential to apply the technique to process control is introduced."

Jan 1, 1999

By Y. H. Liu

Several foaming aluminum samples of different density were prepared in a semi-industrial scale experimental system. Their properties such as the energy absorption characteristics, mechanical properties, heat conductivity and acoustical properties were measured. The results showed that the foaming aluminum with a density of 0.5 to 0.6 g/cm3 has the best energy absorption and this makes it suitable as the ensuring bar of the automobiles and also as a cushion material for the engine. The foaming aluminum with a density of 0.25 to 0.4 g/cm3 has the best acoustical properties and heat conductivity resistance, which is suitable for the door filling material, the ceiling and the partition of the car engine.

Jan 1, 2003

By Yoshihiko Maeda

"Although Japanese mining industry once had been a polluter of toxic heavy metals and gasses, it has been struggling for improvement of environment at mining and smelting facilities under the strict Japanese regulations. Through these efforts, the industry has developed various environmental technologies to be applied in other industries and society.Recycling of metal scraps, for example, has been conducted at smelting facilities. Treatment of hazardous waste, cleanup of contaminated soil and management of landfill are other examples of application of mining and smelting technologies and facilities. In accordance with the worldwide environmental concerns, the industry has become one of the leading industries to promote ""Sustainable Development"", and it is expected further contribution in reducing various environmental burdens to earth by utilizing its mining and smelting technologies and facilities. Some of the examples of these applications are presented in this paper.IntroductionDowa Mining Co., Ltd., established in 1984, is known as one of the ~op Japanese producer of nonferrous metals. Base on its special expertise in the mining and smelting of complex ores, it has expanded its business areas to downstream activities ranging from highly purified metals and alloys, electronics materials, chemicals and related various businesses. Dowa Mining now is becoming more active in the field of waste treatment and recycling.Dowa Mining had operated some mines until 1980th, located at the western part and northern part of Honshuu Island in Japan; the former is pyrite mine while the later is ""Black Ore"" mine,· a complex sulfide ore composed of high grade of copper,· silver, lead and zinc. However, due to the strong yen began in1985; Dowa Mining closed its mining operation in 1994, and has sifted to mining operations in Mexico."

Jan 1, 2000

By Nicola Baldo, Marco Pasetto

"The paper presents the results of a laboratory study, conducted at the Experimental Road Laboratory of the University of Padova, in order to verify the possibility to use different types of electric arc furnace (EAF) steel slags – in substitution of the natural aggregates – in the composition of both dense graded and porous asphalt mixes for flexible road pavements. The research has been articulated in a preliminary study of the chemical, physical, and mechanical properties of the EAF steel slags, and in the following mix design and performance characterization of the bituminous concretes, through stiffness modulus tests at various temperatures and permanent deformation (creep) tests. All the mixtures with EAF slags have satisfied the requisites for acceptance standardized for the road sector, thus resulting as suitable for use in the construction of infrastructures, moreover presenting higher mechanical characteristics than those of the corresponding asphalts with full natural aggregate. IntroductionSteel is produced industrially employing two main technologies: the integral cycle, which starts from mineral iron, and the electric cycle, which uses scrap metal. A consistent amount of the steel produced in Italy (approx. 55%) comes from Electric Arc Furnaces (EAF), which every year, alongside the steel, produce approximately 2 million tons of slag. The recycling of this waste product to produce new high-quality raw materials would reduce both the exploitation of limited natural resources and the amounts of refuse. In the European Union, 60% of slag from EAF is still today disposed of in dumps. The extremely diverse origins of scrap metal (waste from mechanical manufacturing, industrial and civil demolition, car bodywork, etc.) means that the by-products generated by the smelting, slags and ashes, contain different elements, in varying composition, also depending on the type of steel to be produced and the consequent adding of binding and melting elements during the production process. For this reason, iron and steel industry electric furnace slag - unlike the blast furnace dross utilised in cement works, which has a more uniform composition as it comes from a more standardised cycle – has been viewed in the past with some diffidence and so, at least in Italy, the possibilities of its re-use have never been fully developed."

Jan 1, 2008

By Hiroyuki Matsuura

Treatment of electric arc furnace (EAF) dusts has become an important issue from the viewpoint of the environmental protection and recycling of variable resources because these dusts contain considerable amount of zinc and lead. A new recovery process of these metals has been proposed, in which the metals in the dusts react with waste polyvinyl chloride to form metal chlorides. Therefore, it is important to clarify the physicochemical properties and behaviors of zinc, lead and those chlorides and oxychlorides. In the present study, the kinetics of chlorination of ZnO, PbO and ZnFe2O4 mainly contained in the EAF dusts were investigated at 1023 K to 1273 K with Ar-O2-Cl2 gas. Based on these results, the selective chlorination and evaporation process of zinc and lead from the mixture of Fe2O3-ZnFe2O4-ZnO-PbO was examined and the high efficiency of selectivity has been demonstrated.

Jan 1, 2006

By Wayne Bell, Xiaodi Huang, Matthew Andriese, Jiann-Yang Hwang, Zhiwei Peng

"The equations for determining microwave field attenuation length and half-power depth in magnetic materials were derived from Maxwell’s equations. The microwave field attenuation length and the half-power depth for a magnetite concentrate were calculated and the temperature dependence of them was determined. It is demonstrated the microwave field attenuation length and the half-power depth highly depend on temperature and decrease with increasing temperature up to 900 °C. The variations of field attenuation length and the half-power depth with temperature indicate the microwave power attenuates much faster than the field strength in materials. The evaluations of field attenuation length and microwave half-power depth can be used to characterize the microwave dissipation behaviors in the sample and optimize the dimensions of the material in microwave heating.IntroductionMicrowave has been applied in materials processing for its distinguished advantages including rapid heat transfer, volumetric and selective heating [1,2]. However, most research work involving microwave heating are confined to non-magnetic materials (e.g. ceramics), with limited attention paid to the heating of mixed property materials (e.g. magnetite and other ferrites) under microwave irradiation [3-5]. Since many magnetic materials exhibit good and even better microwave absorption capability than non-magnetic counterparts, it is quite necessary and deserved to take advantage of this property and then improve the heating efficiency. To achieve this aim, further understanding on the microwave heating mechanism, especially the microwave propagation/dissipation behaviors in magnetic materials is required.The dissipation behavior of microwave in materials has been identified as one of the key factors that affect the efficiency of heating under microwave irradiation and this behavior can be characterized by several parameters. Apart from traditional penetration depth (TEM power penetration depth, Dp = 1/(2*a), where a is the TEM field attenuation factor), two other parameters, field attenuation length (Df) and half-power depth (Dh), are also applied to indicate the microwave dissipation in materials [6].The accurate determination of such parameters can help in optimizing the dimensions of the load in a microwave furnace, producing more uniform heating under microwave irradiation and avoiding thermal runaway."

Jan 1, 2011

By Dennis J. Kemp

Laterite projects are found in the tropical and sub-tropical regions of the world. As a result severe meteorological situations accompany such projects, often in regions of high seismic activity and political uncertainty. Frequently, socio-economic development supported by political interest is a major driver for development, while environmental protection imposes numerous stresses on the project. This paper will review and examine the many social, environmental, technical and financial issues that a mining and extraction process is subject to during development. The options that must be evaluated will be discussed in the context of sustainable development. Issues of project standards and cultural impact through to long-term issues such as greenhouse gasses and climate change will be assessed in redirecting project environmental norms. Although a rationale for sustainable project can be developed many long- term uncertainties around issues remain. Keywords: sustainable development, communities, social issues, standards, energy, waste management, consultation, agreements

Jan 1, 2004

By Yong Hwan, Wang Jian-Jun, Cai Jiu-Ju, Chen Chun-Xia

"The quantity of residual-heat and its recovery in some Chinese sinter plants are investigated. The main factors affecting energy consumption are analyzed using exergy analysis combining energy level analysis. It is indicated that the “gradation recovery and cascade utilize” of discharged gas and sinter residual heat in different temperature is the direction and the available approach to reduce energy consumption of the sinter process. Taking an iron& steel enterprise as an example, the three-ranked scheme of residual-heat recovery is put forward: ?Part of the sinter gas is used for warm-up and dryness; ?The high-temperature part of the cooler and exhaust-heat boiler are actualized as a closed-circuit, which can produce high-quality steam to generate electricity. ?The waste air in low-temperature part is introduced to sintering machine to support combustion. According to the CDQ which can recover the coal heat, the assumption of pot-recovery is put forward to replace the belt cooler. The two equipments of residual-heat recovery are analyzed in the aspect of energy consumption and CO2 reduction.1. IntroductionEnergy consumption in sintering is only inferior to iron-making in iron& steel enterprises, accounting for 10%~20% of the total energy consumption. A lot of residual heat is produced during sintering, and mostly from the sinter ore and waste gas. Sensible heat of hot sinter ore and discharged gas have accounted for 60%[1] (equals to 40 kgce/t-ore), which are the key point of sintering waste heat recovery. Discharge gas of sintering is mostly composed of flue gas deriving from sinter bed’s combustion, and the content distribution of H2O and O2 and the temperature of the gas along the length of belt-type sintering are shown in Figure1[2,3]. Currently, the sensible heat of hot sinter ore is mainly recovered by circular cooler and cooled by blasting air: the temperature of cooled discharge gas brings down from 350? to about 100? along with the decrease of sinter ore temperature. It is significant to recovery and reuse the waste heat as 4000~6000m3 discharge gas per ton of ore can be produced"

Jan 1, 2008

By Jr. Loper, M. H. Kim, H. H. Jo, C. S. Kang, T. S. Song

"An investigation has been conducted to describe the effect of grain refiner (e.g.,Ti) or modifier (e.g., Sr) on the microstructure of an Al-11.3wt%Si alloy produced by the Ohno horizontal continuous casting process using a heated mold so as to obtain directional solidification at high cooling rate of 300 to 2000°C/s. Experimental results demonstrated that the directionality of the primary a grain was promoted by the addition of0.2 to 0.4%Ti or by the addition of0.02%Sr, whereas the addition of0.6%Ti suppressed this directionality. Feathery a grains were promoted by the addition of 0.2%Ti, while these feathery a grains were suppressed when over 0.4%Ti (grain refinement) or when 0.02%Sr was added. The addition of Ti also resulted in increased coarsening of the eutectic Si in these Al-1 l.3wt%Si alloys.IntroductionThe mechanical properties of conventionally cast Al-Si alloys can be enhanced through judicious control of the casting parameters, by the addition of grain refiners (e.g., Ti) and by the addition of eutectic modifiers (e.g., Sr).[1-3] The Ohno continuous casting process[4-5] uses a heated mold (maintained at a temperature above the alloy liquidus temperature) to produce a casting with a mirror surface free of shrinkage defects. The process is especially suitable for the production of high quality and non-deformable rods of small diameter. This study was conducted at investigate the effects of Ti and Sr on the microstructure of Al-1 l .3wt%Si rods cast by the 01).no process."

Jan 1, 1998

By LeRoy C. Prichard

The scrap based steel producers in the United States generate an estimated 650,000 tons of electric arc furnace (EAF) dust annually which is classified as hazardous waste, K061. These scrap based producers commonly referred to as mini-mills represented 39% of the steel produced in 1994. Based upon the EAF plants being installed or planned today, it is a reasonable projection to anticipate 50% of the steel produced in the United States will be by EAF's. Using a straight line projection of percent of steel produced to tonnage of EAF dust generated, this will result in 833,000 tons of dust being generated upon the completion of these new EAF producing plants, presumably by the year 2000. Because the United States is a capitalistic economy, a steel producer is in business to make a profit therefore dust management becomes a very important variable in the cost of making steel. An EAF mini-mill dust management program must consider at least three components. First the handling of the dust must be in accordance with the law; i.e., the Environmental Protection Agency rules and state and local municipalities guidelines governing K061. Second, it must be an economical solution that allows a company to manage its dust processing costs, a component of its total steel production costs while producing steel at a profit. Third, the dust management program should be one that is environmentally responsible; viz., the program should reclaim or recycle the dust constituents, as feedstock materials or saleable products. The first component, obedience of the law seems to be a relatively straight forward, common sense objective; however, as nearly every mini-mill operation will testify it has been a area of changing laws with confusing variations when it comes to K061. Even more frustrating is the fact that obedience or compliance today does not mean that the company will be considered law abiding in the future.The liabilities associated with

Jan 1, 1995

By Tatiana Pereira Moreno, Priscilla Aki Mori de Hanashiro, Viviane Tavares de Moraes, Denise Crocce Romano Espinosa, Hugo Hashimoto

"Nowadays, End-of-Life (EoL) Liquid Crystal Displays (LCDs) are traditionally disposed in landfills. The increasing access to LCD technology over the last years by Brazilian consumers has intensified LCD' s disposal as an environmental and economic issue. This study aims to characterize used LCDs to identify the main components for recycling. Characterization was performed through scrap disassembly and its components were identified, separated, and weighted. LCDs were disassembled and the following divisions were applied: screen, metal frame, polymeric frame, polymeric sheets and electronic part. Some techniques were used to determine the concentration of Indium in the LCD, the glass/plastic ratio and the different kinds of polymers that compose the screen. The techniques used for characterization included inductively coupled plasma optical emission spectrometry (ICP-OES), Fourier transform infrared spectroscopy (FTIR) and thermogravimetric analysis (TGA). This method, when applied to a wide range of LCDs, can allow the development or improvement of an EoL management of LCD.IntroductionWaste Electrical Electronic Equipments (WEEEs) are waste from discarded equipment, such as computers, monitors and cellphones [1]. Over the past years, treatment of WEEE has been emphasized. It occurs due to the technology's advancement that leads to an even larger increase of WEEES [2].Among WEEEs, there are the liquid crystal displays (LCD). LCD technology is applied in cell phones, tablets, computers and monitors. Nowadays, it's the most well known technology when it refers to monitors, due to its advantages over the Cathode Ray Tube (CRT) technology. Some of them are energy saving, smaller size and no radiation emission [3].This feature in the LCD's global market along with the speed at which electronic equipment becomes obsolete affects society economically and ambiently.This issue becomes even more serious when considering the final destination of the liquid crystal displays. LCDs are lead to landfills as other WEEEs. Besides the different materials long degradation time, the environment is damaged by the disposal of the potentially reusable and hazardous materials [ 4]."

Jan 1, 2014

By Johan Sundström

Anhydrous DyC13 was prepared by dehydration of DyCl3?6H20 in a fluidized bed using both batch- wise and continuous feeding. A gas mixture with varied composition of argon and HCl was used. The productivity was high, reaching values of 0.25 mol H20/m2-st during the reaction step 6- 1 and 0.062 mol H2O/m2.s during the reaction step 1-0. The product was free from hydrolytic compounds, such as DyOCI, if control of inlet gas composition versus temperature was achieved. From the results of various experiments, some relations between HCI-concentration and temperature in order to avoid hydrolysis have been deduced. The fluidization process efficiency decreases drastically after the dehydration has proceeded down to about 10 mol% of remaining water. Therefore, in a final treatment the last traces of water were removed by slowly purging gas through a packed bed. The water content could thereby be reduced to less than 1 mol%.

Jan 1, 1997

By Bora Derin, Adnan Aydin, Onuralp Yucel, Hakan Morcali

"The steelmaking industry which uses electric arc furnaces (EAF) generates approximately 250.000 tons of EAF flue dusts annually in Turkey. These flue dusts contain valuable metals such as zinc, iron and lead. For example, if these flue dusts can be treated efficiently, disposal problems certainly decreases and annually almost 40.000-75.000 tons of zinc can be recovered. In this study, powder and pellet forms of EAF flue dusts taken from a steel mill were carbothermally treated in a temperature controlled pilot scale rotary furnace via carbothermal reduction in order to investigate the reduction behavior of Zn and Pb. Temperature (900-1000 and 1100 °C) and time (0-90 minutes) were selected as reaction parameters. The chemical analysis was performed for the sample residues.IntroductionTurkey’s steel production reached to 23.3 million tons in 2006. There are three integrated steel plants of which capacities vary from 0.7 to 3 million tons per year and seventeen EAF steel plants of which capacities vary from 0.06 to 2 million tons per year [1]. When it is considered that more than 74 % of the Turkish steel production is produced by EAF method and approximately 10 - 15 kg of dust is formed per ton of steel during this process, the amount of annual generated EAF dust may be estimated at approximately 0.25 million tons. EAF dust which contains valuable metals such as zinc, lead, iron, cadmium, and chromium, is considered as hazardous waste product in steelmaking industry. If these flue dusts can be treated efficiently, not only the disposal problems certainly decrease, but also annually almost 40.000-75.000 tons of zinc can be recovered. Many studies which exist on recovering of the valuable metals from EAF dust, propose and practice many hydro-metallurgical and pyro-metallurgical treatments [2- 7]. In this study a laboratory scale work were performed to investigate reduction behavior of zinc and lead in EAF dust by carbothermal process in a rotary furnace."

Jan 1, 2008

By Yang Tian-zu

The separation of precious metals from base metals containing in gold-antimony alloys by selective chlorination leaching under controlling potential was studied in this work. The effects of the consumption of hydrogen peroxide, the concentration of hydrochloric acid, the concentration of sulfuric acid, leaching temperature, leaching time and the liquid-solid ratio in hydrochloric acid system on the leaching efficiencies of the base metals have been investigated. The optimal leaching conditions of the gold-antimony alloys are as follows: hydrochloric acid concentration 4.0mol?L-1, sulfuric acid concentration 1.2mol?L-1, liquid-solid ratio L:S=7.5:1, the leaching temperature 80 0C, leaching time 2h, and the oxidation potential of the leaching system 400±20mV( vs SCE).The leaching efficiencies of copper, nickel and antimony are more than 99% and the gold leaching efficiency is about 0.042% under the above leaching conditions. The base metals containing in the gold-antimony alloy are separated from the precious metals thoroughly.

Jan 1, 2006

By Richard LeSar

Sustainability requires more from engineering than the development of technology. Engineering must also take into account the effects of that technology on the integrated social, economic, and environmental processes that constitute our society. Schumacher introduced the powerful concept of an appropriate technology, by which he meant a technology that is appropriate to the environmental, educational, cultural, and economic situation for which it is intended. While the principles of appropriate technology have been most commonly applied in the developing world, they are equally valid in the developed world as well. In this paper we will review appropriate technology and discuss its role in helping to define a way to think about this broad view of sustainable engineering. We will end by presenting one strategy for introducing the concepts and applications of appropriate technology in an engineering curriculum.

Jan 1, 2010

By Tianyou Huang, Yuan Lu, Haimin Long, Jinwu Kang, Gang Nie

"The distortion of metal parts during heat treatment process is one of the main obstacles in industry to ensure high-quality work and less or no machining allowance, especially for large but thin steel castings such as heavy turbine blades. In the paper, a method is proposed to control the distortion by adjusting heat transfer coefficient of metal parts during heat treatment process. Required heat transfer coefficients can be realized by getting the metal parts into contact with various media such as water spray, insulation felt or materials with different heat conductivity. The control method based on this idea is set up and achieved. By using insulation felt and water spray to change the heat transfer coefficient during the stages of heat treatment process, the results indicate that the proper control time and vary with materials.IntroductionThe distortion of metal parts during heat treatment process is one of the main obstacles in industry to ensure high-quality work and to realize less or no machining allowance [1]. For example, the Three Gorges turbine blade’s distortion is as large as 50mm during heat treatment process. The uneven heating and cooling during heat treatment process is the main reason for distortion [2]. By adjusting heat transfer coefficient of different areas of metal parts, the heat treatment process could be controlled. The temperature variation, direct cause for distortion, could be under control. Loeser Klaus used high pressure gas to achieve uniform heat transfer during gas quenching and proposed the possibility to use ""Dynamic Quenching"" processes where the quenching severity is varied during quenching by stepwise control of either gas velocity or gas pressure [3]. Li Zhichao also suggested minimizing distortion by marking a component into several areas and imposing different heat transfer coefficients on each area [4]. Heat transfer coefficient can be controlled by getting the metal parts into contact with different media such as water spray, insulation felt, air or different heat conduction materials. In addition, the exact time to adjust the heat transfer coefficient is another factor for distortion. A method is presented in this paper by actively adjusting heat transfer coefficient for different areas of metal parts and different stages of heat treatment process to control their distortion. The corresponding experiments have been made by using different metal materials."

Jan 1, 2012

By Andre Krzysik

"Fluidized bed technology has been used in the industry for almost 100 years. To fully understand the process hundreds if not thousands of researchers were and are involved in finding the way to predict the behavior of the solids when subjected to the flow of media through them and the conditions of the solids in the fluidized state. The difficulties in predicting the behavior of solids in the fluidized state stem from the complexity and abnormality of the parameters related to the solid particles. Theoretical calculations can in some degree account for some of them. Particle size distribution, their shape, density, moisture content and physical and chemical reaction that may exist in the fluidized bed reactor play an extremely important role and influence the behavior of the fluidized bed. This paper focuses on the practical examples of the fluid bed equipment and the use of different conditions to process various products.IntroductionEach process application has its own unique requirements and the designers of the equipment must take into consideration specific process requirements, specific properties of the material to be processed (both physical and chemical), and physical and chemical reactions/changes that are taking place in the reactor (heat and mass exchange, chemical reactions, isomorphic change etc.). Each individual piece of equipment must also satisfy specific requirements/ preferences of the client that will operate and maintain the equipment. Those often represent greater challenges than the process on its own, and are equally important to the satisfactory operation of the plant. That includes aspects like location of the equipment, environmental effects, and expected life of the equipment, process control, access, maintenance, and many others.Over the period of time a great deal of research, both theoretical and practical have been carried out and the results of that work are available for equipment designers. For the simple applications that information is usually sufficient and the selection of a suitable solution is relatively simple. In many instances, the available information is not sufficient, and often specialized test work needs to be conducted to obtain additional data. In many cases a pilot installation is built in which the required process is tested. Only then the commercial equipment is designed. The following deal with specific installations that were designed to satisfy specific requirements. In some instances, additional problems were discovered during the commissioning of the equipment that required on site modification. The continuous monitoring of the equipment that was supplied to the various clients allowed us to further develop and improve our designs."

Jan 1, 2014

By A. N. Aposhian

The electronics industry generates tin/lead bearing by-products that can be recycled for their metal value. This paper will cover the processes used to recycle these tin/lead bearing byproducts from the plating, circuit-board fabrication and assembly industries. Though these processes are well known to the companies who do the recycling, few outside the industry including the generators of the by-products, understand the processes or needs of the industry. This paper will give a broad overview of these processes, and describe the services provided by this industry. The paper will also touch upon the future of the recycling industry, including the legislative and environmental push for the elimination of lead from electronics.

Jan 1, 2000