Search Documents

By In-Hyeok Choi

Currently, spent V2O5–WO3/TiO2 catalysts contribute significant amounts of solid waste following increasing levels of global demand. V2O5–WO3/ TiO2 catalysts usually consist of TiO2 anatase as a supporting oxide, vanadium as a catalytic agent, and other promoters such as tungsten, silicon, and calcium. Although vanadium is the main catalytic agent, a relatively high content of tungsten (WO3, 7–10 wt%) typically exists compared to vanadium (0.5–1.5 wt%). Considering the irreplaceable properties and industrial importance of tungsten, a feasible method for the recycling of spent V2O5–WO3/TiO2 catalyst should be established to utilize it as a secondary source. This paper presents a process to recover tungsten from spent V2O5–WO3/TiO2 catalyst. The processes proposed here involving roasting, decomposition using HCl, ammonia leaching, and crystallization. Within the process, ammonium paratungstate (71 wt% as WO3) is obtained as a final product. The total yield rate of tungsten from feedstock was found to be 96.3%.

By Courtney Young, Jerome Downey

"The various technologies developed for treating spent potlining (SPL) from primary aluminum smelters have been reviewed on several occasions. The technologies generally involve physical, chemical, and thermal processes, either individually or in combination, with the primary objective of total recycle, waste minimization, or complete disposal. In general, those technologies geared for recycling involve separations and are therefore subject to recovery inefficiencies that are attributed to several factors. However, the inefficiencies could be reduced or possibly eliminated if the pots were designed for recyclability. This concept is applied to SPLASH, a recently developed SPL management technology.IntroductionAluminum is produced by molten salt electrolysis via the Hall-Héroult process. The process is conducted in an electrolytic “pot,” which is comprised of a steel frame first lined with insulating refractory brick, and then conductive graphite blocks, which serves as the carbon cathode [1, 2]. These materials are collectively referred to as “potlining.” Anodes comprised of petroleum coke/pitch are suspended above the pot and extend down into the molten cryolite (Na3AlF6) electrolyte. The electrolyte temperature is maintained at approximately 980 °C by resistance heating as low voltage (4-5 volts) and high current (50,000-300,000 amps) are applied across the two electrodes.High purity alumina is added to the cryolite bath, where it dissolves and becomes amenable to aluminum reduction at the cathode:"

Jan 1, 2008

By Motoyasu Sato

Highly pure pig irons were produced in a multimode microwave reactor from powdered iron ores with carbon as a reducing agent in the nitrogen atmosphere. The grains in compacted powder absorb microwave energy selectively. Microwave-matter interaction creates thermal non-equilibrium state microscopically and enhances chemical reactions and the phase mixing at the grain boundaries very rapidly. The visible light spectroscopic techniques was used to monitor the progress of the reactions. Up to 650°C, the heated powders radiate the continuous spectrum of blackbody emission. The small non-equilibrium hot spots rise, move and finally burst in to brighter light emitting from all over the surface at 650°C. CN molecules and Fe (I) atoms were identified in the recorded spectrum. These bursts are similar to the ?ignition propagation? normally observed in chemical reactions. The line spectra originated from CO molecules have not been detected yet. The solid-solid reaction could be expected between the iron oxides and carbon to produce CO2 directly. A loss in the sample weight was accelerated during the excess-emission. These are the clear evidence that microwaves cause thermally non-equilibrium state and accelerate reduction process. The reduction of iron ore is completed at 1380°C and relatively very pure pig iron was produced. It should be noted that the impurity level of Mg, S, Si, P and Ti is only 5-10% of what is found in the pig irons produced by modern conventional blast furnaces in the steel industries. The necessary amount of carbon needed was 1/2 compared to conventional blast furnace to produce the unit weight of steel, if we applied renewable energy or nuclear power for the microwave excitations.

Jan 1, 2006

By G. R. Waters

NMR360 is developing a suite of chloride-based metals extraction processes, with the first commercial operation scheduled for commissioning late in 2018. It is critical, therefore, that with the introduction of any new technology, that the circuits do not suffer from mechanical failures which will compromise the operation. Although chloride leaching is at atmospheric pressure and relatively low temperature, the main challenge is preventing corrosion, since the high proton activity makes even a small amount of acid behaves as though it were concentrated. An additional challenge in concentrated chloride circuits is the potential for solids precipitation. In this context, therefore, correct valve selection is crucial, and NMR360 has partnered with CGIS to ensure that the Severe Service Valves (SSVs) needed will perform over and above the definitions of the Manufacturers Standardization Society (MSS) of the Valve and Fittings Industry. This paper outlines what the minimum requirements are for SSVs in chloride leaching applications, drawing on five decades of industry experience from one of Canada’s leading valve experts.

By Naiyi Li, Henry Hu, Alfred Yu

"In the past few years, various squeeze cast aluminum components have been developed and successfully implemented in various vehicles by the automotive industry because of their superior engineering performance. However, fundamental understanding of the formation of air gap during squeeze casting processes is still very limited despite of its significant influence on the extent of heat transfer between the casting and mould. In this paper, a mathematical model has been developed to simulate phenomena of air gap between the casting and mold' during squeeze casting of aluminum alloys. The model considers the effect of process parameters such as applied pressures and mold temperatures on the events of air gap formation. The predication indicates that the occurrence of highly enhanced heat transfer in squeeze casting of aluminum alloys primarily results from the presence of excess applied pressures.IntroductionA number of squeeze cast Al components has been developed and used in mass-produced vehicles in the past few years, such as steering knuckles, Road wheel, Engine Block etc. This is attributed to their superior engineering performance. In squeeze casting, the cooling rate can be increased by applying high pressure during solidification which results in the noted refinement in the micro structure scale leading to better casting properties. However, the excessive pressure increased interfacial heat transfer coefficient is affected during the solidification by air gap formation and die surface condition etc., which is believed to increase thermal resistance at the casting/die interface [l - 4]."

Jan 1, 2004

By Mingming Zhang

"Three samples received from the EAF shop have been characterized by chemical, X-ray diffraction (XRD), optical microscopy (OM) and scanning electron microscopy (SEM) methods. The objective of this characterization work is to investigate the occurrence of nickel, copper, zinc, sulfur and phosphorus in these samples and identity their origin and associations with iron minerals in the concentrate samples that are from mines.The samples were identified as Mineral, Pellet, and HRD. The latter is the DR! product. All three samples were received as fine powders. The results indicate that, in the mineral sample, magnetite is the major iron oxide mineral with hematite as a second phase based on the OM and XRD studies. Pyrite [FeS2], chalcopyrite [CuFeS2] and bravoite [(Fe,Ni)S2] are major sulfide minerals. Trace amounts of apatite [Ca5(P04)3(F,Cl,OH)], wardite [Na4CaA112(P04)8(OH)8 6H20], giniite [Fe5(P04)4(OH)3 2H20] and vivianite [Fe3(p04)2 8H20] were identified by SEM and XRD. Microscopic studies also indicated that most of the sulfide grains in the mineral sample are present either as liberated fine particles (about 10 microns) or as inclusions within the magnetite and hematite grains. XRD studies revealed magnetite as the major mineral with subordinate amounts of hematite and pyrite confirming the microscopic findings. Copper, nickel, and zinc are mainly present as chalcopyrite, bravoite, and franklinite [(Zn,Mn,Fe)(Fe,Mn)204] in trace amount in the mineral samples, respectively. Impurities carry over to the Pellet and HRD samples.Chemical analyses of the three iron-bearing samples indicate that sulfur and phosphorus in the Pellet sample exceeded the specification. Since liberated pyrite and chalcopyrite particles were observed both in mineral and pellet samples, magnetic and flotation processing routes for this ore should be effective for sulfide removal but at the cost of iron losses. The high phosphorus content of all three samples indicates that there are phosphates which are difficult to remove by the current concentrating process (magnetic separation and flotation)"

Jan 1, 2012

By Stéphane Bourg

The SCRREEN project gathers more than 50 European initiatives, associations, organisations or independent experts working on Critical Raw Materials (CRM) into a long-lasting network including stakeholders, public authorities, and civil society representatives. SCRREEN contributes to improve the CRM strategy in Europe by (i) mapping primary and secondary resources and substitutes of CRMs, (ii) estimating the expected demand of various CRMs in the future and identifying major trends, (iii) providing policy and technology recommendations for actions improving the production and the potential substitution of CRM, (iv) addressing specific waste electrical and electronic equipment (WEEE) and other End-of-Life (EoL) product issues related to their mapping and treatment standardization, and (vi) identifying the knowledge gathered over previous years and making the data accessible to those beyond the project. As a first step, SCRREEN worked at providing stakeholders with a comprehensive analysis of the current use of the CRM, the mapping of potential primary and secondary resources, and identification of the key technologies used in their production. Substitution profiles, analysis of European business and policy issues pertinent to CRMs, and an identification of the standards, policies, and regulatory frameworks concerning these CRM was also completed. In a second step, to be conducted between mid-2018 and mid-2019, SCRREEN will provide guidance for improving the CRM market in Europe by identifying opportunities from research, development, and innovation (R&D&I) that could reduce the supply and/or economic risks around the most relevant CRM for Europe.

By Wilson Pascheto

This paper presents results of investigations performed as part of a Root-Cause-Failure-Analysis (RCFA) of a DC smelting furnace that was brick lined with MgO-based refractories. An unusual continuous contraction of the furnace hearth was identified during operation. Cracks in the refractories were envisaged after a major shutdown of the furnace. To determine the mechanism and causes of the unusual contraction behaviour of the furnace hearth, refractory samples were taken from the furnace at different locations and subjected to different analysis including Scanning Electron Microscopy (SEM), Energy-dispersive X-ray spectroscopy (EDX), QEMSCAN and Electron Probe Micro Analysis (EPMA). Creep testing of refractories under different loads (ASTM C832) was also employed to evaluate the mechanical integrity of the used bricks in comparison with the new ones. Results of the various characterisation analyses revealed that there was an interaction between refractory bricks and molten material during furnace operation, which resulted in reduced creep resistance of the MgO-based refractories. This was verified by comparing creep performance of the used brick samples and new brick samples at different temperatures and applied stresses.

By Yurniko Nakamura

Hydriding properties and crystal structure of a Ti-V- Mn solid solution alloy have been studied by P-C isotherm measurements and neutron and X-ray powder diffraction. The absorption P-C isotherm at 298K shows two plateau regions at 0.01MPa and 1MPa. The X-ray diffraction data have demonstrated that three phases with a BCC, a pseudo-cubic FCC and an FCC structure form subsequently with increase of the hydrogen content. Crystal structure of the latter two phases has been determined by Rietveld refinement of the neutron diffraction data. The FCC phase is the di-hydride of CaF2 type with hydrogen occupation in the T sites. The pseudo-cubic FCC phase is the mono-hydride of NaCl-type with hydrogen occupation in the 0 sites, which has not been reported so far. The lattice constants of the mono-hydride (Ti1.0V1.1Mn0.9)H_2.7 are a'=0.407 nm for two axes and c'=0.390 nm for the third axis. The a'axis is shorter by 4% than the c'axis. This pseudo-cubic FCC lattice is formed by contraction of 5% of the a axis and expansion of about 30% of the c axis from the original BCC lattice.

Jan 1, 2002

By Björn Lindquist

Boliden has developed a number of specialised technologies for smelter gas handling and effluent treatment. These technologies will be described. Special attention will be given to the high-pressure venturi, Editube wet electrostatic precipitator, mercury removal processes, and two-stage effluent treatment.

Jan 1, 2002

By Takashi Araki

In this work, we have elucidated the two-step oxidative reaction mechanism of 2,4,5-trichlorophenol by adsorbing oxygen atom for oxidative decomposition reaction of 2,4,5-trichlorophenol on oxide catalyst surface using ab initio molecular orbital calculation. In the first oxidation, total energies of reaction products have been shown extremely stabilized at all oxidation positions. This reaction occurs due to charge transfer from benzene ring to adsorbing oxygen atom. As a result, 1£ bonding of benzene ring are weakened. However, the benzene ring of 2,4,5-trichlorophenol does not perform cleavage reaction. In the second oxidation, the benzene ring of2,4,5-trichlorophenol can perform cleavage reaction, since the second oxidation obtains larger stabilized energies than the first oxidation.

Jan 1, 2003

By James D. Navratil

Neutral bifunctional organophosphorus solvent extractants (such as carbamoylmethylphosphonates and carbamoylmethylphosphine oxides) strongly extract lanthanides and actinides and do not extract more than 40 other elements from mineral acids. Because of their excellent properties they have been found useful for F-element recovery and purification processes. A brief overview of the lanthanide and actinide extraction chemistry of these reagents will be given.

Jan 1, 1990

By J. H. Corrigan

A series of six papers describing the Falconbridge Dominicana Ferronickel project were presented at the International Laterite Symposium held as a joint project of TMS-AIME in February 1979 at New Orleans. A review of the ore mineralogy, as well as. the processing and environmental practices as they exist today at Falcondo with emphasis on modifications put into practice since 1979 are presented in two papers: Part I.- Mineralogy and Ore Dressing E.W. Lithgow - General Superintendent ? Mines Falconbridge Dominicana, C. por A. Bonao, Dominican Republic Commercial volumes of nickeliferous laterite ores overlie part of a 90 km long belt of peridotites in central Dominican Republic. Protores are serpentinized harzburgites and dunites, with lesser serpentinite. The ore mineralogy consists mostly of goethite, serpentine-group minerals, quartz and poorly crystallized, X- ray amorphous materials. Minor constituents are hematite, gibsite, olivine and enstatite. In the Ore Dressing plant, the mine feed is subjected initially to proper sizing and blending to produce a homogenized mix. Subsequent drying and upgrading, by selective crushing and screening of rock kagments through a Barmac circuit, complete preparation of the ore for pyrometallurgical processing. Part II.- Pyrometallurgy, Fuel and Power Generation J.H. Comgan - Manager ? Production Falconbridge Dominicana, C. por A. Bonao, Dominican Republic Falcondo's energy requirements are based on oil which is refined on site to provide distillate to carry out drying and selective reduction of the nickeliferous ore in the shaft furnaces, plus bunker oil to produce electrical power for process melting, refining and ancillary use. The dryer product at 1.68% Ni is briquetted and passed counter current to hot reducing gas in 12 vertical shaft furnaces. The hot calcine discharge is melted in two high power electric furnaces at very high secondary voltage. The crude ferronickel is ladle refined and cast as 15 kg ingots or 125 gm ferrocones.

Jan 1, 1993

By K. S. Kawatra

In recent years, there have been several efforts to develop binder mixtures for iron ore pelletization. Some efforts have been fruitful, while others have encountered failure. For example, adding corn starch to bentonite is effective, while adding fly ash to bentonite is not. When binders are made with fly ash, a pozzolanic reaction occurs, but no such reaction occurs when bentonite and corn starch are used together. The authors analyzed which binders can be mixed, and which binders will succeed. The authors confirmed this analysis with several laboratory and plant studies. This paper presents this critical analysis, along with various combinations of binders for making Iron Ore Pellets.

By W. G. Davenport

Chapters 7,8and 9 calculated three combinations of: blast composition (mass% O2, mass% N2) oil quantity per tonne of concentrate blast temperature that will steadily produce molten 65% Cu matte from pure chalcopyrite-concentrate. The combinations are:

Jan 1, 2001

By E. A. Thiers

The causes of structural changes in the markets for high technology alloying metals are discussed in terms of technological, economic, and financial trends. Recent market imbalances have affected producers in developed and developing countries differently. Possible response strategies for suppliers in the two types of countries are examined that may alleviate future market imbalances.

Jan 1, 1988

By Pengcheng Li, Wei-Tong Du, Yu Wang, Gang Wen

Carbon dioxide could be utilized as a weak oxidant and a kind of coolant to oxidize elements, meanwhile, helping control the temperature during the converter vanadium extraction process. However, the optimum content of CO2 and the cooling effect of CO2 at low content have not been reported. In this study, experimental research based on the influence of different CO2 contents from 0% to 25% injected to the vanadium-containing hot metal was carried out, as well as contrast experiments of O2-N2 mixed blowing. The results indicated that the optimum content of CO2 was 15%. Under the optimum condition, the oxidation of [C] was the lowest and the oxidation rate of [V] was 96.9%, while the temperature was also lower than the O2-N2 mixed blowing. This paper provide a potential property for utilizing CO2 during the converter vanadium extraction process.

Jan 1, 2016

By Kathryn A. Mrotek

The textural growth patterns of nodules from two areas in the North Pacific and the South Pacific are characterized by mottled, columnar and compact-type zones. Amorphous material (mainly iron and manganese hydrox-ides) is a botryoidal-forming phase in the mottled and columnar zones. Crystalline material (platy crystals of birnessite and crystallites of todo-rokite) is found primarily in the mottled zones on botryoidal structures or as long-protruding structures growing onto that portion of the nodule in contact with the underlying sediments. The long-protruding mottled zones contain little or no biogenic debris, suggesting that these zones grew un-interruptedly within the underlying sediments. The coalition of spheroidal knobs comprising some of the nodules also suggests a relatively long residing time within the sediments. It appears that crystalline material (the usual host to associated valuable metals) forms in a quiet environment and as a result of direct nodule association with the underlying sediments.

Jan 1, 1982

By J. R. Hartin

Traditionally, many of the advances in casting technology have been made by expensive and time consuming trial-and-error methodology. Modeling of the complex solidification process promises production of castings which are made "right the first time." Even though several models are available for simulation of conventional casting processes, none of them address this relatively new technology of investment cast titanium aluminides. In this paper, modification and application of a transient, three-dimensional, fully coupled fluid flow and heat transfer solidification modeling computer program to the analysis of centrifugally cast titanium aluminides is discussed. The predictive results of the program are compared to qualities of actual cast parts for validation.

Jan 1, 1992

By Takashi Araki

In this work, we have elucidated the two-step oxidative reaction mechanism of 2,4,5-trichlorophenol by adsorbing oxygen atom for oxidative decomposition reaction of 2,4,5-trichlorophenol on oxide catalyst surface using ab initio molecular orbital calculation. In the first oxidation, total energies of reaction products have been shown extremely stabilized at all oxidation positions. This reaction occurs due to charge transfer from benzene ring to adsorbing oxygen atom. As a result, ? bonding of benzene ring are weakened. However, the benzene ring of 2,4,5-trichlorophenol does not perform cleavage reaction. In the second oxidation, the benzene ring of 2,4,5-trichlorophenol can perform cleavage reaction, since the second oxidation obtains larger stabilized energies than the first oxidation.

Jan 1, 2003