Search Documents

By Ted D. Johnson

INTRODUCTION The tailing dam is part of the SOHIO L-Bar Uranium Mine and Mill located about 70.8 kilometers (44 miles) west of Albuquerque in northwestern New Mexico. The dam location is shown on Figure 1. The tailing dam is one of the last upstream method dams permitted in the industry. Design and construction aspects of the project, as well as operation and maintenance considerations, are reviewed herein. Since initial construction, SOHIO Western Mining Company and Woodward-Clyde Consultants have developed several modifications and improvements in the dam's operating and monitoring procedures. This work has been done in coordination with the New Mexico State Engineer's Office and in accordance with recommendations in a report done for the Corps of Engineer's Phase I Dam Inspection Report. Modifications and improvements described should be of particular interest to owners and operators of other tailing dams utilizing the upstream method of deposition. The tailing facility was designed for a 10-year life to provide an ultimate storage capacity of 6 1/2 billion kilograms (7 1/2 million short tons) in an area of about 180 acres. A plan view of the tailing dam is shown on Figure 2. The tailing consists of approximately 75% sand size material and 25% fines (material passing the No. 200 sieve). The tailing dam includes a small earth starter dam with raises of the dam accomplished using tailing deposited by upstream method techniques. The starter dam is a homogeneous embankment about 610 meters (2000 feet) long, a maximum height of 12 meters (40 feet) and 2 1/2:1 (horizontal to vertical) upstream and downstream slopes. The starter dam contains an internal drainage system which includes a near vertical chimney drain connected to horizontal finger drains. A typical section through the maximum height of the starter dam is shown on Figure 3. A small confining dam, approximately 1.6 meters (5 feet) high, is constructed beyond the limits

Jan 1, 1980

By W. J. Stone

In response to concerns over the impact of mining on the hydrologic balance at the Navajo Mine in northwestern New Mexico, a recharge study was conducted using a chloride mass- balance approach. Impact of mining on annual recharge volume was assessed by comparing pre- and post-mining recharge values. The mean regional recharge rate for reclaimed ground (weighted by acreage) is 1.02 mm/a (0.04 in. per year) or twice that for undisturbed ground, 05 mm/a (0.02 in. per year). Comparison of regional recharge volumes for identical areas shows mining increases recharge 92%. The increase is only 80% if no closed depressions are constructed during reclamation. However, the increased rates are so low that there should be no detrimental impact on regional water resources. The chloride method proved useful at Navajo Mine and should succeed at others surface coal mines as well.

Jan 1, 1991

By C. Caceres

Fibre reinforced shotcrete in combination with other types of support systems is becoming the leading support method for underground excavations, especially those present in low quality rock masses. Sudden or rapid ground support failure can expose workers to safety hazards, damage to equipment and others resulting in production interruptions that will impact the cost of operation. Knowing the peak and post-peak strength characteristics of the support system over time are of major importance. Round Determinate Panel Testing of fiber reinforce shotcrete is the primary test used by the mining industry to determine strength characteristics; however, the tests are costly and significant manpower is required in a mine environment to build, store, handle and test the panels. For these reasons numerical modeling can result in an effective method to produce realistic results. This paper examines the strength characteristics Round Determinate Panel tests and its ultimate application in underground excavations, using Itasca?s three dimensional particle flow code (PFC3D).

Jan 1, 2010

By C. A. Hollingsworth

The Deep Leg Flotation Cell was developed to solve a problem which confronted the Smith-Douglass Company on moving from one mining area to another. Poor recovery and, to some extent, inferior concentrate grade were encountered in the silica flota¬tion circuit. This was believed due to the softness of the phosphate which caused it to form slime. In view of the urgency of the matter, the problem was attacked from two angles. The first involved the development of a flotation cell which would not create slime and the second, a new or improved reagent for floating silica from phosphate rock which would be less sensitive to slime than reagents currently in use.

Jan 1, 1964

By K. Tempel

In December of 1999, Newmont Mining Corporation’s Eastern Nevada Operations commissioned its commercial biooxidation facility. The commercial biooxidation facility is a refractory gold whole ore heap process that uses bacteria to assist with the oxidation of sulfide minerals thus liberating occluded gold for further processing by cyanide for gold extraction. Before the commercial biooxidation facility was started, a decade of research went in to developing this state-of-the-art process. During final design and construction of the commercial facility a decline in gold price necessitated cost saving and project scope changes. As a result, the biooxidation process experienced many challenges. Some of the more significant challenges include poor heap permeability due to haul truck stacking, unhealthy bacteria population due to a lack of solution aeration, and insufficient biooxidation time because of limited pad space and high carbonate content in the ore. This paper discusses the many challenges encountered and addressed during the first 2-3 years of commercial biooxidation operation.

Jan 1, 2003

By Abdullah Arik

In deposits with highly skewed grade distributions, such as precious metals deposits, proper handling of the outlier high grade data is very crucial to the ore reserve estimation. Although some recent geostatistical techniques are available to handle the estimation problems with these outlier data, ordinary kriging or conventional methods are still widely used to estimate the ore reserves for such deposits. One reason for this is the fact that the alternative methods offered are either too complex or too exhaustive for the mine engineers and geologist who often do not have the expertise or the time to apply these methods. This paper presents a new 2-step kriging algorithm "Outlier Restricted Kriging" (ORK) which can be a simple and a practical tool to use where the ordinary kriging will fail to handle the outlier high grade data properly in block grade estimation. The paper details the methodology and discusses the results of its application to a gold deposit.

Jan 1, 1992

By Richard B. Berg

California was a major talc-producing State until the late 1980s when production from the deposits in the Death Valley area ceased because of a number of factors which included pressure to discontinue mining in and around Death Valley National Monument, and health concerns affecting markets for tremolitic talc. The states of Montana and Texas now account for slightly more than half of U.S. talc production. Deposits in an area encompassing southern Death Valley and extending east into the Kingston Range were formed by contact metamorphism of carbonate beds in the Precambrian Crystal Spring Formation next to Precambrian diabase sills. These deposits contain ore ranging from high-purity, fine-grained talc to platy, tremolitic talc with high brightness. Deposits of tremolitic talc and talc schist in the Silver Lake District in San Bernardino County resulted from metamorphism of Precambrian carbonate beds intruded by granitic plutons. Northeast in Esmeralda County, Nevada hydrothermal alteration related to Late Jurassic plutons caused talc replacement of Precambrian to Early Cambrian dolomite. A hydrothermal origin is also indicated for talc deposits in the lnyo Range just north of the Death Valley District where bodies of unusually pure talc occur in Paleozoic lime- stone near Jurassic granitic plutons. Talc is now mined from a deposit in the foothills of the Sierra Nevada Range southeast of Sacramento where quartz-mica schist of the Permian Calaveras Formation has been hydrothermally altered to talc. Replacement of magnesite of the Precambrian Allamoore Formation produced talc deposits mined in the Allamoore District of west Texas. This dark-gray talc of low iron content with carbon- aceous material and dolomite is ideally suited for use in ceramics where it makes a white product when fired. Small bodies of platy light-pink to white talc suitable for use as an extender in paint are also mined in this district. In the Llano District of central Texas talc has replaced impure carbonate rocks and serpentinite. All Montana talc production is from deposits in the southwestern part of the State that formed by Precambrian hydrothermal alteration of dolomitic marble. This alteration produced material with high purity that ranges from very fine-grained, massive talc to coarser grained, foliated talc. Markets include pitch control in paper, paint, cosmetics, ceramics, rubber and plastics. In southwestern and northeastern Oregon, talc has replaced serpentinite in the vicinity of Mesozoic plutons. Soapstone for carving is mined from a southwestern Oregon deposit. Deposits of similar origin occur in central and northwestern Washington.

Jan 1, 1995

By Rustu S. Kalyoncu

Rainbow colors of roofing granules, adorning the roofs of buildings from single family units to largest office buildings, have their origin in the roofing shingles as burlap soaked with tar appearing as early as the 1700s. Dusting of talc and mica on the coated surfaces, to keep roofing from sticking to itself in storage, represents an early improvement to the original construction product. Sometimes, colored, natural mineral dusts were added as color pigments within the dusting material, for initial color. Prolonged exposure to sun caused the asphalt to become brittle, and it eventually cracked and leaked. Search for solutions to cracking and subsequent leaking problems eventually led to the use of crushed mineral granules on asphalt coated shingles. This provided the impetus for further growth in the asphalt roofing industry. Application of a layer of crushed mineral on the asphalt coating minimized the coating deterioration from exposure to ultraviolet light, thus significantly improving the shingle life. In the 1900s, screened waste from slate quarries was the most commonly used granule in asphalt roofing products. Records indicate the use of coarse slate screenings for asphalt roofing as early as 1906. As the asphalt roofing industry further developed, other naturally colored minerals, such as silica sand, quartz, mica, feldspar, talc, slag, granite, rhyolite, and oyster shells were used on roofing surfaces. Later on, a number of manufactured granular materials, such as crushed brick and tile, fire clay, and white porcelain were used. The first artificially colored roofing granule was produced in 1914 by running molten slag into a solution of alkaline metal silicate, which was absorbed by the porous slag. Various colors were obtained by adding pigments to the silicate coating and by subsequently heat treating the granules. In 1922, another technique was developed in which green slate granules were saturated with copper sulfate solution and heated to 760°C to form copper oxide. Since then, many other granule coloring processes have been patented, one of the most significant being the sodium silicate coatings introduced around 1975. Granules as used in construction (specifically roofing materials) are defined as natural or synthetic-mineral grains smaller than gravel and larger than sand in particle size. They are used primarily for protective and decorative purposes on the weather- exposed surface of asphalt composition roofing. Development of artificial coloring techniques has made it possible for the roofing industry to provide asphalt roofing shingles in a wide variety of colors complementing the color and style of buildings. Roofing granules, as we see today, are the products of long technological evolution.

Jan 1, 1994

By E. D. Thompson, Y. J. Zhang, K. F. Unrug

This paper presents the results of a recent study on the development of an in situ testing method for determining coal strength in mine pillars. The strength testing is performed in the horizontal holes drilled into the coal rib using a penetrometer, which is an hydraulically powered device that uses an indenter to press on the surface of the borehole until the load reaches the failure point of the coal. The pressure and the penetration of the loading pin are recorded by a data-acquisition unit. The results collected from several coal mines indicate that this testing method is ideally suited for the realistic coal strength measurements. The new testing system not only improves the accuracy of the pillar-strength determination, but it is more cost efficient than the conventional method.

Jan 1, 1997

Relatively few longwall mines in the U.S. operate under multiple seam conditions where the two seams are less than 200 ft apart. This paper describes the experience of six that do. These operations are located in PA, WV and UT, and include examples of both undermining and overmining. Some operate above or beneath their own workings, others are in historic mining districts and must contend with abandoned mines that are decades old. The lessons that these mines have learned cover a broad range of topics, including: • Whether to stack gateroads or place them under old gob areas; • How to size pillars and select artificial support to cross longwall stop lines; • How to use yield pillars to minimize multiple seam stresses and coal bump potential, and; • When to anticipate the creation of pathways for gas, water, or oxygen between current and abandoned gobs.

Jan 1, 2007

By George D. Lessner

I'm sure that everyone at this meeting is aware of the current problems facing the U.S. metals mining industry. Prices are depressed and expected to remain depressed for quite some time. On the other hand, industrial minerals, including talc, are doing quite well. The profitability of industrial minerals has sparked considerable interest on the part of many companies in expanding into industrial minerals. Our company is one of those actively seeking to expand its position in industrial minerals. It is appropriate that the A.I.M.E. asked me to speak to you regarding entry into the talc business. So how do you get into the talc business? Earlier speakers have explained how to locate, mine, process, and market talc, so you have the "how ton.

Jan 1, 1984

By Stanley Bunk

The fluidized bed was invented by Fritz Winkler of Germany in 1921. The first application in the U.S. was in the development of the fluidized bed catalytic cracking of petroleum in 1942. Today, fluid bed cracking reactors are an integral part of every oil refinery. When fluid bed technology was first considered for applications outside the petroleum industry it was recognized to have uniform temperature, close control of the gaseous atmosphere and excellent mixing between solids and gases. Roasting of sulfide ores and concentrates was an obvious match. The first application was a single stage roaster for gold refining in 1947. There have been over four hundred commercial fluid bed roasters built and operated successfully in the four decades since the fluid bed was invented. There are three general categories of roasting applications. The largest number of roasters fall into the dead roasting category which includes gold ore roasters. The other categories are sulfating roasters and partial roasters (Reference 1).

Jan 1, 1990

By V. A. Scovazzo

The analytical pillar design procedure employing the Wilson equation is based on the site-specific material strength of the floor, pillar, and roof rock. Stable pillars so designed will sometimes be larger than those designed using empirical methods thus providing more stability or at other times smaller than empirically designed pillars thus conserving natural resources. Presented here is a detailed procedure for the analytical design of soft rock pillars using the Wilson Equation. An example of this procedure is presented that uses data from a mine in the Owl Seam in Southern Appalachia. These Owl Seam pillars are now in use and are performing as expected. Also addressed is an assessment of the Dr. Scovazzo?s analytically designed pillars based on pillar performance data gathered by Dr. Mark in the Southern Appalachian Coal Field.

Jan 1, 2010

By Hasan Sevim

A computerized heuristic model for an efficient and economic design of belt haulage networks in underground coal mines is discussed. The model is versatile, easy to use, and is valid for all mining methods singly or in combination. It may be used to design new networks or to analyze existing networks. The input data required are 1. maximum production rates from a section, 2. probabilities of production rates, 3. equipment costs, and 4. data necessary for network coding to represent different cases. The objective function is the "expected minimum cost per ton of coal hauled" while meeting production requirements. The output includes belt width, motor horsepower, bin size etc. and also values of operating parameters for each belt such as belt speed, effective tension, power consumption etc. A detailed account of the cost involved is also provided for each unit as well as for the entire network. Description of the model and an example of the design of a belt network in a mine with two longwall and four development sections are presented.

Jan 1, 1986

By J. D. Miller, Z. S. Nickolov

Sum Frequency Spectroscopy (SFS) is a powerful nonlinear optical technique to study interfaces at the molecular level. SFS has one major advantage over conventional vibrational spectroscopic methods, such as infrared (IR) absorption and Raman scattering, in that the method is inherently interface specific. As a result, the spectroscopy of molecules residing in the interfacial region can be probed selectively without any contributions from the molecules present in the more pervasive bulk phases. Analysis of SF spectra can yield information on population, structure, and orientation of interfacial species with several nanometers in-depth resolution. The recently acquired SF spectrometer at the University of Utah opens new possibilities for investigation of interfacial phenomena of great importance for separation technology, materials research, nanotechnology, bioengineering. Its application to studies of liquid/gas, solid/liquid, and solid/gas interfaces will be discussed.

Jan 1, 2004

By D. Oyler

The National Institute for Occupational Safety and Health’s(NIOSH) Pittsburgh Research Laboratory (PRL), RAG Pennsylvania and Strata Control Technologies of Australia have collaborated to conduct an extensive study of roof bolt strata interaction at the Emerald mine in Southwestern Pennsylvania. The primary goal of the project was to obtain detailed data on the interaction between the mine roof and the support elements for use in modeling studies. The study site was a longwall tailgate subjected to high horizontal stress. Three arrays of instruments were installed at the site, one in the tail-gate entry and two in an adjacent crosscut. Pumpable concrete cribs were present in the tailgate array, and cable bolts were installed in one of the crosscut arrays. The instruments included mechanical and sonic extensometers for measuring roof movement, instrumented roof bolts, and three-dimensional roof stress cells. The study was ultimately successful in determining the magnitude of the horizontal stress concentration, the height of roof failure and the roof failure sequence, and the loading history of the primary roof supports.

Jan 1, 2004

By R. R. Smith

The meaning of the title, "Blank Piece of Paper," refers to the need for management to take a completely fresh viewpoint to the problems facing our industry. These problems are so severe and some so new that conventional thinking may not be adequate to resolve them. Innovation has to be a part of every company's approach to the solutions, our concept is to start with a "Blank Piece of Paper.' The objective of 'this paper is to outline steps which can be taken to improve the profitability of a mining business. This is not an examination of technical solutions to individual problems, but rather recommendations for overall change in management thinking. This philosophy is based on our actual, hands-on experience in major open pit operations worldwide over the past 25 years.

Jan 1, 1987

By N. R. Billette

In 1982 and 1983, a study was undertaken to analyse the applicability of Elbrond?s analytical model to suit the needs of Lake Asbestos of Quebec in their computerized open pit planning and scheduling strategy. The immediate goal was the assessment of the optimal allocation of trucks and the determination of the extra cost of in-pit blending. Data from 45 tonne trucks was used to estimate the mine capacity based on a fixed assignment policy. The tonnage yielded by the analytical model was compared with the results of a simulation program. Another point that the study high- lighted was the definition of efficiency parameters for the haulage system: shovels-trucks-crusher. The efficiency, both of the utilization of financial resources and of the operations, for the overall system reaches optimal values in very precise conditions for the number of pieces of equipment in operation. Such a parameter is proposed as a standard for the definition of an optimal number of trucks and shovels in operation. Deviations from this optimum do occur in a well-planned system for qualitative goals. These can then be quantified in terms of costs to the mining company.

Jan 1, 1986

By S. L. Bessinger

The need for improved safety and productivity brought about the introduction of longwall mining to the Appalachian coal fields. These same forces continue to drive developments in modern longwall equipment and mining practices. Current initiatives to improve productivity and safety are focused on automation and the effects of scale in equipment design. Longwall roof-supports, shearers and face-conveyors have changed significantly. Panel layouts have evolved to include larger total tonnages and provide for more rapid development of gate-entries. These advancements have improved longwall productivity and new production records are continually being set. Roof supports Reliability is implicit in the quest for automation. It is impossible to automate equipment if it is not reliable. To a large degree, this has been the problem with longwall shield automation efforts. The "electronic control" of shields depends on the proper functioning of electronic equipment, electrohydraulic valves and full-flow service valves onboard every support.

Jan 1, 1995

By T. Weimer

Gasification of carbonaceous energy carriers with simultaneousCO2 removal is a new and interesting alternative e.g. ZECA [1],HyPr-Ring [2], AER [3]. In the ZECA process lime supported Hydrogen generation from Methane is a basic process unit and the Hypr-RING process investigates Hydrogen generation from hard coal with addition of lime. Here the main objective is a further development of the AER process. High energetic efficiencies for gasification in the range of 90 % can be achieved if the humidity of the energy carrier is already sufficient for steam reforming reaction. The aim of the overall process is upgrading coals and biomass yielding into three valuable products: • A fuel gas ready for power generation • A CO2gas stream containing >95%, ready for transportation to disposal or chemical fixation • A pre-calcined feed for cement clinkering consisting ofCaO and coal ash Thus power generation and gasification are independent. A promising industrial application is the combination of gasification and cement production. Then only one additional reactor is required and the precalcination mass flows have to be increased.

Jan 1, 2004