Search Documents

By J. Litsenberger, T. E. Marshall, P. R. Coyle, L. J. Prosser, A. T. Iannacchione

For the first time in an underground stone mine, the relationship between roof movement and microseismic emissions was examined in conjunction with two distinct roof fall areas. As roof monitoring increases in acceptance and monitoring technology advances, the goal of providing reliable roof fall detection systems to enhance the safety of underground mine workers moves closer to reality. Instrumental to reaching that goal is the ability to interpret accurately and completely roof movement and microseismic emissions, which can serve as precursors to roof falls. This paper examines the capabilities of convergence and microseismic monitoring systems to better understand roof rock failure mechanics and to anticipate roof falls. An understanding of how these techniques are used and how they interact with each other is critical in developing the most effective ground control strategy for our nation’s mines.

Jan 1, 2004

By Wolfgang R. Wawersik, Charles M. Stone

INTRODUCTION Hydraulic fracturing was applied in horizontal drill- holes in the Salado salt formation near Carlsbad, New Mexico. Tests were performed approximately 650 m be- low surface to validate the design of a Waste Isolation Pilot Plant (WIPP) for the disposal of radioactive waste from defense activities of the United States. Hydraulic fracturing was performed primarily to determine whether the virgin in situ stress state at the WIPP site is isotropic and whether the magnitude of the virgin in situ stresses corresponds to the weight of the overburden. Beyond these limited objectives, however, measurements are now being reviewed to evaluate the usefulness of hydraulic fracturing in salt formations in general. Such measurements are desirable to determine stresses induced by mining and to monitor time-dependent stress changes around underground excavations in salt masses. Hydraulic fracturing was chosen because it is the only technique that can be readily applied in virgin ground far from existing mine openings. The method also appeared to yield directly the magnitude of the least compressive principal stress, regardless of the mechanical properties of the rock mass. A knowledge of the least principal compression was deemed sufficient to establish the isotropic character of the virgin in situ stress field under two conditions: (1) the Salado formation was mechanically isotropic, i.e., the fracture toughness did not vary normal and parallel to bedding so as to permit preferred fracture paths, and (2) pressure measurements were combined with determinations of the orientations of hydraulic fractures and, more generally, with observations of the characteristic hydraulic fracture patterns. The latter was possible by locating the drillholes for hydraulic fracturing along the axes of drifts that were mined several months later. The success of general stress measurements by hy- draulic fracturing of salt subjected to anisotropic stress conditions was and remains less certain. While the smallest in situ compressive stresses should still be equal to instantaneous shut-in pressures, there may not exist any unique relationships between the greatest and intermediate in situ principal stresses on one hand and the primary breakdown and fracture reopening pressures on the other. This problem would be a consequence of stress relaxation due to salt creep around any drillhole in which hydraulic fracturing tests are conducted. Moreover, lab- oratory measurements suggest that creep and stress relaxation could be so rapid that it might not be possible to interpret the measurements for anisotropic stress conditions even if hydraulic fracturing were performed as soon after drilling as possible. The primary objectives of the stress measurements in the WIPP were met by combining hydraulic fracturing tests with finite element analyses of the effects of salt creep, observations of hydraulically induced fracture pat- terns, and laboratory hydraulic fracturing tests on oriented core. In situ hydraulic fracturing tests in long drillholes were preceded by several trial tests to establish the best test methods and to demonstrate that salt could be fractured. The resolution of anisotropic stresses and special problems, e.g., in the identification of instantaneous shut-in pressures, are currently being addressed in hydraulic fracturing tests in a mine pillar, in tests following different delays between drilling and fracturing, and in tests with different frac fluids. This paper will review the main results of the analyses above and of one group of hydraulic fracturing tests at different distances from existing excavations. The paper will conclude with a brief description of the geometry of the hydraulically induced fracture patterns. Because of space limitations, it will be assumed that the reader is familiar with hydraulic fracturing or will first consult other sources (e.g., Cleary, 1980; Gronseth and Detournay, 1979; Zoback and Haimson, 1983; Nemat-Nasser et al., 1983; Kim et al., 1984)

Jan 1, 1986

By M. B. Mooiman

Cyanidation of gold and silver ores by conventional mining and milling techniques has been practiced for over a century. During the past decade, heap leaching has emerged as a viable process for treating certain gold and silver ores. (1) The rapid development of heap leaching for gold and silver ores is largely a result of lower capital and operating costs and faster start-up time than that offered by conventional mining and milling. In general, these features make heap leaching an ideal approach for exploiting either small or large low-grade disseminated deposits of gold and silver considered to be uneconomic by conventional methods. The development of heap leaching technology has evolved from the operations initiated in the western United States. The basic components of a typical heap leaching operation are depicted in Figure 1. Run-of-mine or crushed ore (usually 1 to 5 ppm gold) is delivered to specifically prepared impervious pads. Alkaline cyanide solution is applied to the surface of the heap and allowed to percolate through the heap (typically 10-30 ft high). Pregnant leach solution which drains from the heap is collected and stored in tanks of sufficient size or in collection reservoirs. Gold and silver are recovered from the pregnant solution and the barren solution is recirculated back to the heaps after reagent make-up.

Jan 1, 1983

By L. M. Gochioco

The Seismic Interactive Interpretation Workstation (S//W) provides a wide spectrum of utilities ranging from improving field acquisition techniques, data processing and interpretation of coal seismic data. The power of the workstation lies in the interpretation process where various sets of geophysical and geological data are integrated to form a network of information that is stored in a database. Computer models are generated from known borehole and geologic information and later cross-correlated with the processed seismic data. Structural and stratigraphic modeling techniques add another dimension to the interpretation process. Complex trace attributes highlight subtle features not easily observed in black and white sections. Using the computer workstation, the explorationist gains valuable insight and conducts more intelligent interpretation of seismic data through a more comprehensive network of data analysis.

Jan 1, 1992

By Joseph J. Garbarino

World demand for phosphate fertilizers has grown at an average annual rate of between 6 and 7 per cent over the past 10 years. In the next five years world demand is expected to at least continue to grow at that rate. Also, the continued need for improved fertilizer materials, coupled with improvements in fertilizer technology, have placed added importance on the use of phosphoric acid as a starting material for high analysis phosphate fertilizers. This demand for phosphates and phosphoric acid must be met by increased production. Increased phosphoric acid production also brings increased demand for chemical processing agents including foam control agents. We at Arizona Chemical Company have closely followed the phosphate fertilizer industries needs. Arizona Chemical Company has been an important supplier of flotation agents to the phosphate industry, primarily from its Panama City, Florida plant. We have also recognized the important role played by foam control agents in the wet-phosphoric acid manufacturing process. We feel it is the responsibility of the supplier of foam control agents to offer specifically designed products that are highly efficient and economically useful. The difficulties involved in evaluating foam control agents in the plant are recognized. Owing to the large number of variables present, and the difficulties in controlling these variables during the period of a plant trial, plant evaluation of a large number of foam control agents is impractical. We have attempted to develop a practical, reproducible, and yet rapid, laboratory evaluation test which correlates with plant performance.

Jan 1, 1966

By Barbara H. Carroll

In order to rapidly evaluate an area for its mineral potential, a reconnaissance exploration program generally includes the following: 1. Outlining an area of interest 2. Identifying known mineral deposits 3. Bibliographic search of the literature 4. Evaluation of geochemical and geophysical surveys 5. Compilation and review of geologic maps The information now available from various government agencies regarding the mineral deposits, geology, and geochemistry may be integrated and used as a tool to rapidly evaluate an area before the field season. The databases most commonly used in the United States are the USBM MAS/HILS system and the USGS MRDS system for their information on mineral deposits; GEOREF and GEOARCHIVE for bibliographic information; and NURE data for the geochemistry and geophysics. In conjunction with the project geologist, this information may be used to plot known deposits and their geochemical signature as well as any other areas of like signature for further examination.

Jan 1, 1985

By Greg Bold, Mahmood Khwaja, Yuannian (Jerry) Wan, Michael S. Schultz, William Simcoe

Beaver Creek Clean River Project will satisfy the consent decree requirements by capturing and treating combined sewage overflows. The project consists of, approximately, 2,700 feet of 30-inch trenchless pipe installation, a new screening/disinfecting facility, an expansion of an existing diversion structure, and a 72-inch internal diameter, 530-foot long mined tunnel. The tunnel portions are being progressed as early release packages. This paper presents the geotechnical exploration program and the subsurface conditions encountered; interpretation of the geotechnical conditions; and, approach to developing stand-alone packages for the tunnels to mitigate construction and schedule risks and continue to advance the project.

Jun 13, 2021

By J. W. Gunnett

Abstract. The Surface Mining Control and Reclamation Act of 1977 (PL-95-87), Section 522, establishes requirements for state regulatory authorities to designate lands unsuitable for all or certain types of surface coal mining. Any party having an interest in an area that may be affected can petition for it to be designated unsuitable for mining. Section 522 could present major obstacles to the mining industry by typing up an area in an endless round of petitions. The program under development for Kentucky is examined and analyzed as an example for determining the hidden impacts of Section 522.

Jan 1, 1980

By Richard D. Zigmond

In this paper, a computer program that has been developed for determining the capital and operating costs for coal preparation plants is described along with its applications. The logic of the computer program is based upon the results of a survey of existing preparation plants, operators, plant contractors, equipment manufacturers, and consulting firms. This survey provided information on plant performance, order-of-magnitude costs, and costing procedures. Additionally, an extensive cost data file for the major capital equipment in coal preparation plants has been developed. Using the washability data and the computer program outputs, the cleaning costs per million Btu can be calculated. Details about the program and its applications can be found in a report by the authors (Zigmond et al., 1979).

Jan 1, 1981

By Y. J. Wang

This paper describes a graphical technique by which the operating points for a two-fan ventilation system can be represented as the intersection of the modified fan curves. In constructing the diagram, the air quantities associated with the fans are considered to be independent variables and employed as the axes of a rectangular coordinate system. The diagram may include, in addition to the modified fan curves, contour lines for resistances, pressures, and air powers. Procedures for drawing the diagram are discussed and illustrated with an example of the ventilation system.

Jan 1, 1985

This paper presents a method for evaluating the economic feasibility of solution mining a hypothetical uranium roll-front deposit. It is assumed the wellfield will be operated in a prudent manner and that leaching tests were performed in depth in both lab and field (push-pull) prior to startup. Leach test results are reduced to two important parameters and used as the basis for solution mining a wellfield. This case study assumes a 10 mil- lion-lb uranium deposit with 40 possible small wellfields; four are kept in operation simultaneously until the deposit is depleted. The wellfields have different ore reserves and grades, lixiviant circulation rates, leach rates, and peak concentrations, and thus the daily uranium production will vary. Daily production is used to assess the profitability of a particular lixiviant and the mode of well- field operation in light of realistic market price estimates. The mathematical procedure is simple and straightforward, based on reasonable in-situ leaching relationships as well as accepted accounting practices.

Jan 1, 1985

By Norbert Patzelt, Johann Knecht, Wolfgang Baum

The principle of high-pressure interparticulate comminution has been used very successfully since the mid 1980's for grinding a wide range of different materials. A number of reports about operating experience have already been published. High-pressure grinding rolls (HPGRs) are currently making their debut in the mining industry. Experience is being gained with test machines, particularly for the comminution of hard rock. In the grinding of diamond-bearing ore, (Fig 1) interparticulate comminution has already become the standard for liberating the diamonds from the matrix. The advantages of interparticulate comminution are also recognized for the grinding of concentrates (chrome ore, iron ore). Numerous HPGRs are being used very successfully in this field. A testing plant for first-time industrial grinding of coarse, very hard and highly abrasive copper ore was built at Cyprus Amax's plant in Sieretta, Arizona (Fig. 2). The operating experience gained here showed that the grinding of very hard ores places particularly high mechanical demands on the mill. While the machine itself meets the high availability requirements, the wear-protection system proves to be the most sensitive point. Naturally, the properties of the ore to be ground exert a considerable influence on the lifetime of the grinding rolls. This paper describes the wear mechanisms and the wear­protection systems designed to combat these.

Jan 1, 1997

By K. E. Hjelmstad

Solution mining operations often encounter difficulty maintaining adequate leach solution flow into the ore formation because of loss of formation permeability near the injection well. Permeability loss caused by swelling and breakup of clays and fine particle migration can often be the cause of the problem.

Jan 1, 1989

By E. J. Sullivan

This study seeks to define the mechanism of oxyanion sorption onto surfactant-modified zeolites. Zeolites which have been treated with hexadecyltrimethylammonium bromide (HDTMA) surfactant to produce a hydrophobic surface are capable of sorbing both organic compounds as well as oxyanions such as chromate, selenate, and sulfate. Simple ion exchange and charge-balancing mechanisms do not fully explain this unusual phenomenon. The sorption of HDTMA surfactant appears to be partly ion exchange and partly sorption to non-ion-exchangeable sites. Sorption of chromate is a simple exchange mechanism with bromide, which co-adsorbs with HDTMA to form a surface precipitate. Information from this study will be used to design on-site and in situ treatment systems for contaminated water, such as filter beds and permeable barriers.

Jan 1, 1995

By B. J. Arnold

Utility coal specifications usually contain a requirement for a maximum moisture content in order to prevent coal handling problems and to minimize evaporative losses in the boiler. As most coal cleaning processes are water-based, dewatering and sometimes thermal drying steps are required to meet moisture specifications. Screens are often used for dewatering, with centrifuges and filters used to further reduce moisture in many cases. Algorithms to predict the performance of commercial dewatering devices were developed for the Coal Cleaning Simulator running under Aspen Plus? during a project sponsored by the U.S. Department of Energy and the Electric Power Research Institute. These algorithms include calculations for size degradation in the devices and fines loss to effluents, where appropriate, and a calculation for moisture content of the product based on particle size and specific gravity distribution. This paper discusses the algorithm for coarse and fine coal centrifuges and gives comparisons between predicted moisture and solids loss and published moisture and solids loss values for various particle size ranges.

Jan 1, 1996

By D. E. Ranta, William B. Ryan, Ronald W. May

The Lower Cretaceous McMurray Formation in northern Alberta contains bituminous sands interbedded with other sediments which form the reject encountered during mining operations. Grade prediction is based on a combination of geological interpretation, computer modelling and past mining experience. In addition to estimates for ore, an accurate estimate of "waste" or "reject," are required for Mine Planning. This study investigates the ability of point-kriging using geostatistics, to augment the existing data base of drill-holes in a study area on Syncrude's leases. This approach enables the assessment of potential "worst" case - "best" case scenarios within the context of Mine Planning.

Jan 1, 1992

The long-term goal of the Collaborative Research Centre 525 is the identification of options for the resource-sensitive supply and utilization of metallic raw materials. In order to address these issues, an integrated resource management system for metallic raw materials was developed and tested. Simulations were carried out, using the tools and methodical approaches developed in this system, in order to compare alternative operating scenarios for aluminium and copper. However, before these alternative operating scenarios could be formulated and assessed, it was necessary to develop a consistent set of indicators to monitor progress towards sustainable development in the processing and utilization of metallic raw materials. The primary objective of the centre is to develop a set of indicators, which adopt a holistic approach to resource management, thereby enabling the assessment of different operating scenarios within the broadest possible context. The target audience for this research consists of decision-makers in the realms of politics, business and industry, as well as NGO?s.

Jan 1, 2003

By T. J. McKeon

Gravity separators such as spirals are commonly used in multistage cleaning and scavenging circuits to improve the quality and recovery of concentrates produced in the industrial minerals industry. Unfortunately, field surveys suggest that many industrial operations are poorly configured in terms of equipment layout. This shortcoming can often be attributed to a failure by engineers to make use of fundamental process engineering tools for circuit design. One of the most important of these is linear circuit analysis. This powerful tool makes it possible to mathematically compare the relative efficiency of circuit configurations in advance of experimental testing. This article provides a basic review of the linear circuit analysis concept and discusses some of the key insights it provides for the layout of multistage circuits. An industrial case study is provided to show the tremendous impact that this process engineering tool can have on the design of multistage spiral circuits in a heavy mineral wet plant.

Feb 1, 2012

By Stephen Semeniuk

Discussion by Stephen Semeniuk Discussion As a valuator and SME member, I view Ross D. Lawrence's position as based on unproven and faulty assumptions made with regard to the pragmatic evidence presented in his paper. Moreover, his call for the inclusion of all mineral resources in discounted cash flow valuations is redundant, if not irrelevant, as there are procedures that already take all classes of mineralization into consideration for valuation purposes. In my experience as a valuator, I find that Canadian securities regulators are more than accommodating in allowing any valuations of mineral properties to be based on cash flow calculations. In other business areas, the same regulators usually reject discounted cash flow valuations of projects or businesses with no operating history. Instead, the regulators prefer valuations to be based on other transactions tested in the marketplace. Valuations based on actual market transactions are less subjective than discounted cash flow calculations and/or the capitalization of arbitrary, untested or undemonstrated earnings projections. In the mining and minerals sector, such projections may be made by persons not qualified to make such projections. In support of this statement, I direct readers to the article "Valuation of mineral properties which do not contain exploitable reserves" by Lionel C. Kilburn, which appeared in the August 1990 issue of the CIM Bulletin. To quote from the article: "Value of a mineral property depends basically upon metal prices, recoverable grades, mining and metallurgical practices, commodity supply and demand, and political-economic conditions, all of which vary with time. Five fields of expertise influence the value of a mineral property: •geological engineering, •commodity markets, •financial markets, •stock markets and •mineral property markets. The skills of geologists and engineers properly apply to the first field of expertise. Knowledge and consideration of the other four fields is important, but such advice is more properly sought from marketing experts, economists and stockbrokers." Securities regulators have created no hardship for valuators by excluding unsubstantiated resources in discounted cash flow valuations. In the field of engineering, best design practices apply. A margin of safety is built into the design criteria for any new equipment or structure that will exceed normally expected load levels and stresses, even though such considerations imply higher front end costs. In accounting, the comparable operating principle is conservatism. It explains why, for balancesheet presentation purposes, inventory is stated at cost or market, whichever is the lowest value. Similarly, when the engineering or geoscience-based valuator plays in the field of finance, the rules of accounting and applied economics apply. Regulators in their skepticism of income-based valuations are in tune with similar views already expressed in mining literature. To quote H. Van Tingley, in Mining Magazine, July 1996: "... the DCF method has inherent dangers when applied to undeveloped resources. Firstly, it presents an often-undeserved aura of accuracy. A DCF value is no more accurate than the least accurate of the assumptions incorporated into the calculation - and assumptions

Jan 1, 2003

Ravensthorpe Nickel Operation (RNO) is a major new mine and processing plant currently being constructed by BHP Billiton in a ?green field? site near the small town of Ravensthorpe, about 150 km west of Esperance and six hours drive from Perth in Western Australia. Ensuring that the project has a positive overall impact on the surrounding region and that this extends well beyond the life of the operation will be a major challenge for RNO, state and local government, and the local community. For the last two years, the Centre for Social Responsibility in Mining (CSRM) has been assisting RNO management and the RNO Community Liaison Committee to develop a community sustainability monitoring framework for the project. This paper reports on the process that was used to develop the framework, describes the main elements and briefly discusses key learnings from the exercise.

Jan 1, 2007