Search Documents

By Glenn Boyce, Paul Gribbon, Gary Irwin, Greg Colzani, Jim McDonald

This paper discusses the process utilized by the City of Portland Oregon’s Bureau of Environmental Services (BES) to procure and compensate Impregilo-SA Healy (I/H)for the West Side Willamette River Combined Sewer Over?ow (CSO) Project. The contract method is a three-phase process consisting of qualifications based contractor procurement, pre-construction phase design assistance/construction planning, and facility construction where the contractor is compensated on a cost reimbursable-fixed fee basis. The paper focuses on pre-construction phase lessons learned from the development of the contract general conditions, establishment of a construction budget and cost control program, incorporation of contractor recommended design changes, and development of a subcontractor procurement program for construction.

Jan 1, 2003

By Robert W. Bartlett

Heap biooxidation of sulfidic refractory gold ore requires large amounts of oxygen, as shown in Figure 1. Bacteria, Thiobaci/lus ferrooxidans, are donnant at oxygen concentrations below about 3% in air (1 ppm in aqueous solution) because ofmonod kinet­ics. Hence, the maximum possible utilization is only about 75%, and it may be much less than that due to poor air sweep effi­ciency. At the maximum oxygen utilization, an ore containing two percent pyrite requires nearly 100 cubic meters of air per tonne (4,000 cubic feet per ton). The stoichiometric air require­ment to oxidize arsenopyrite is similar to that of pyrite. While the leaching solution percolating through the heap introduces some dissolved oxygen, the amount is insignificant because of the low solubility of oxygen in water, 7 to 8 ppm at atmospheric saturation. There are only three ways to provide oxygen to the heap: either air flow by natural convection, diffusion of oxygen from the surface (through stagnant air in the air-filled void space in the heap), or forced air ventilation of the heap. Each of these processes will be reviewed.

Jan 1, 1996

Powder River Basin (PRB) mines were originally built to serve power plants designed specifically for their coal. Sulfur was the major concern, with BTU and sodium limiting the market for some. The Clean Air Act has extended the PRB market into plants converting from other coals. These new customers are more sensitive to constituents affecting boiler and precipitator performance. At the same time, the prospect of deregulation is forcing power companies to control cost more stringently than ever. Jacobs Ranch Mine has responded to the changing marketplace with an expanded coal quality and customer service program.

Jan 1, 1998

By Robert S. Ondrey, Robert A. Haney, Kenneth G. Fields

As part of an MSHA program to assess the effectiveness of dust control parameters for longwall mining operations, respirable dust studies were conducted on six longwall sections. The purpose of these studies was to evaluate the influence of airflow and production on longwall dust control. The sections were sampled for 3 to 35 shifts. In addition to dust, ventilation and production measurements, other dust control and operational parameters were measured. The water spray system at each operation conformed with generally recommended practices. Therefore, improvements to the dust control system would be most appropriately achieved through improvements to ventilation along the face. Two methods of assessing the influence of ventilation and production were used. For two of the six mines where extensive sampling (22 and 35 shifts) was conducted, multiple linear regressions were used to relate the dust concentration versus airflow and production data. For these two mines, statistically significant correlations existed between concentration and both production and airflow. The multiple regressions fit to the data indicated that for every 0.47 m3/s (1,000 cfm) increase in airflow, there would be approximately 0.04 to 0.07 mg/m3 reduction in dust concentration; and, for every 1,000 ton increase in production, there would be approximately 0.15 to 0.50 mg/m3 increase in dust concentration. For the four mines with limited data (3 to 10 shifts), as well as for the two mines with extensive sampling, an average ratio of airflow per ton of coal mined was calculated by proportioning the airflow to production and the designated occupation personal respirable dust exposure to a 2.0 mg/m3 concentration. The airflow-to-tons ratio required to maintain a 2.0 mg/m3 dust concentration ranged from 0.0038 0.0071 m3/s per ton (8 to 15 cfm/ton). Both of these data treatments were used to calculate airflow requirements based on normal production rates. For the two mines where both the regression and airflow-to-tons ratio were calculated, results from the two methods agreed within 25 percent.

Jan 1, 1993

By D. R. Nagaraj

There are few organic ligands that can adsorb effectively on noble metals, especially gold, in aqueous media. Ligands containing sulfur and nitrogen donors are known to be the most effective. Dithiophosphorous acids, for example, are known to adsorb on gold under certain conditions and these, along with xanthates, are used traditionally to recover gold values by flotation from ores. These compounds, however, are not necessarily selective for gold since most of the associated sulfide minerals are also floated. Monothiophosphorous acids, on the other hand, were recently discovered to float gold values selectively from sulfide-containing ores in a mildly alkaline medium; thus the dicresyl monothiophosphate is now used commercially in a gold flotation operation in the U.S.

Jan 1, 1991

By M. G. Hester, G. S. Adisoma

To address the problem of grade estimation in a general three-dimensional shape and the uncertainty associated with the estimate, the technique of jackknifing/ block-kriging shortcut is proposed. A new estimator called jackknife kriging is introduced first. Through the jackknife variance, a confidence limit for the reserve-grade estimate can be calculated. Unlike the kriging variance, which is more a measure of data configuration and which is independent of data values, the jackknife variance reflects the true variability of the data. This approach provides a simple way to set a confidence level for global estimation of resources.

Jan 1, 1997

By N. L. Piret, R. J. Wesely, A. E. Melin, A. D. Zunkel

At the end of the sixties new iron precipitation techniques as jarosite, goethite or hematite brought about the new generation of electrolytic zinc plants, thereby terminating the multitude of existing neutral leach residue treatment schemes. Since the eighties, increasing environmental impact considerations urge the conversion of these contaminated waste generating precipitation processes to techniques which either produce environmentally acceptable residues or minimize their formation thereby generating iron-bearing byproducts. Technologies identified and economically assessed include the hematite process either suitably improved or with subsequent upgrading, the iron extraction process and the direct smelting of neutral leach residue to slag and fumed zinc oxide.

Jan 1, 1993

By Randhir Sehgal

Heavy media processes have been used for cleaning +28 mesh coals for a number of years, Two applications, i.e., the vessels and the cyclones are widely used in the U. S. for this purpose. The basic reason for the popularity of these systems is their extremely high efficiencies for particle sizes above 28 mesh, However, application of heavy media technology to fine coals below 28 mesh, has been limited due to the following reasons: o Inability to make size separations effectively at sizes below 28 mesh o Necessity of feeding large quantitites of magnetite to the separators o Difficulty of recovering magnetite in the presence of large quantities of coal o High levels of coal contamination in the recovered media, leading to high circulating loads and ineffective control of media gravity

Jan 1, 1981

By Tom Skodack

Mine and tunnel contractors face a complex environment-one in which economic risks are high, operating costs grow ever higher, ore grades are lower or recovery more difficult, and civil construction projects are intensely competitive on a world-wide scale. Within the context of this environment, the risks and rewards of proper machine selection for rock excavation have become proportionately large. Speed, depth and scope of analysis, and extensive supporting information are indispensable in the selection process. Equipment designs and their applications are also myriad and diverse. Several equipment alternatives and excavation techniques may have to be evaluated at once to choose the most cost-efficient approach. The following examples are typical of the current demand for more detailed equipment analysis: • An aggregate supplier starts a new quarry. He knows his targeted tonnage, blasting restrictions, and previous operating costs from other quarries. But he must improve on his old costs. What drill pattern, hole size, and bench height will give lowest cost per ton? How many crawler drills and what type will produce this tonnage most efficiently? • A mine is using a fleet of twin pneumatic ring drills for long hole drilling to initiate their cave. The mine is facing both air shortages and increasing operating costs with decreased efficiency in the ring drill fleet. If they invest in new hydraulic long hole drills, what impact will each drill unit have on production? Each twin drill unit? What configuration gives best operator efficiency and subsequent reduction in manpower? Which configuration gives the best return on investment? • A tunnel contractor is bidding a long straight water tunnel by conventional drill and blast methods. What is the optimum number of drill booms for the tunnel cross section and excavation schedule? How many rounds per day can he achieve? What are his total project drill, blast, and muck costs? In the past, such questions could be answered, but only approximately at best. One good prediction could involve many hours of laborious calculations that had to be repeated each time a new parameter was introduced or an existing parameter changed. In 1980, increasingly complex analysis, coupled with increasing need and quick response times demanded by industry, led Atlas Copco's project department to turn to the computer. New computer programs based on theoretical considerations and three decades of worksite performance data were developed for evaluating mine and tunnel contractors' equipment needs, productivity, and partial or total operating cost calculations for most conventional drill and blast excavation techniques-including shot rock loading and transportation. This Computerized Analysis of Rock Excavation-or CARE-program has since been available to the mining and construction industry. From each program specific results can be pre- dicted, including: • Productivity Calculations-Rock drill penetration rate for a given drill, hole size, and rock type, optimized for the best drill steel life; net machine productivity (drill-out time or drill meters-footage-per shift); total drill round time, including charging, blasting, loading, and haulage; suggested drill pattern, computer printed, including hole size for a given rock drill, rock type, and associated blasting restrictions for either drift rounds or benching applications; long-hole drill meters (ft) per drill shift; breasting down (upper drilling) drill meters (ft) per drill shift; and comparison between continuous loading machine capacity and LHD capacity. • Operating Cost Calculations-Operating costs expressed as cost per drill meter (ft), cost per cubic meter (cubic yard) of excavated rock, and cost per meter (ft) of tunnel advance. These costs may be calculated using as many cost centers as the mine, quarry, or tunneling contractor wishes. Specific operating costs may cover drill rig operating costs only, less capitalization; drill rig operating costs, including amortized equipment investment; drilling and blasting costs; drill, blast, load, and haulage operating costs; long-hole drilling operating costs per drill meter (ft) or per blasted cubic meter (cubic yard) of rock; and loading and transport operating costs. In all the above cases, any number of cost and capacity calculations may be run by simply changing important cost center variables to judge their net effect. Accuracy as a Function of Input Data and the Statistical Data Base Accuracy of a projection clearly depends heavily on the data base from which the projection is drawn.

Jan 11, 1982

International Technology for the Nonferrous Smelting Industry, by T. K. Corwin et al., Noyes Data Corp., Mill Road at Grand Ave., Park Ridge, NJ 07656, 413 pp., cloth, $36-Describes current and new production processes, and pollution control technology, in the primary nonferrous smelting industry in the US and abroad. The methods described are intended to reduce costs, increase production, and lower pollution levels. Techniques used in copper, lead, and zinc smelting are emphasized and, whenever possible, the authors describe pollution control practices.

Jan 7, 1982

By E. J. Berentsen, R. F. Nanna, D. Dell’ Elce, R. Lougheed

Apollo Gold’s Black Fox project is located 10 km (6.2 miles) east of Matheson, Ontario, Canada, on Hwy 101 East It is located within the prolific Destor Porcupine Fault Zone, which is also the host for the Dome and Hollmger mines to the west and the Holt and Holloway mines to the east. The local host rocks are intensely deformed and carbonized ultramafic volcanics, pillow basalts, syenitic felsic intrusives and argillaceous sediments. Gold occurs with pyrite and as spectacular specimens in native form. Past production accounted for a total of 195,337 oz (6,075,606 g) of gold. Apollo Gold Exploration, Inc. is conducting an intense drilling program aimed at expanding the reserve base.

Jan 1, 2004

By F. Bourgeois, J. A. Herbst, R. P. King

The ultrafast load cell (UFLC) has proved to be an exceptionally good device for the study of the fundamental processes associated with the impact fracture of particulate material. A new high- sensitivity UFLC has been commissioned at the Utah Comminution Center for the study of low-impact energy single-particle fracture. The force-time histories of individual fracture events have been measured. The force and energy absorbed at crack initiation have been measured at several particle sizes. The mass specific energy for fracture and the associated breakage function have been determined. The distributions of particle breakage energy and particle strength have been measured as a function of particle size.

Jan 1, 1992

By John B. Ackerman, John G. Mansanti

INTRODUCTION Placer Dome's Turquoise Ridge Joint Venture operation is located some 75 km northeast of Winnemucca, a community in north central Nevada. Formerly known as the Getchell Gold Corporation and First Miss Gold, the operation mines refractory ore from the Getchell and Turquoise Ridge gold deposits located on the east flank of the Osgood Mountain Range above the Kelly Creek Basin in the Potosi Mining District. Mining has been ongoing at Getchell since shortly after its discovery in 1934, and was the nation's second leading producer of gold after Homestake in the early 1940s. Over its history the Getchell property has been mined for gold, tungsten, molybdenum and arsenic; mining methods varied from open pit mining to underground mining; processing options included conventional milling, flotation, roasting, heap leaching, and most recently pressure oxidation followed by CIL (carbon-in-leach). As an historical note, the US Bureau of Mines developed the use of carbon for gold recovery at Getchell during the 1940s (Horton 1999). Placer Dome acquired the property in May 1999. The pressure oxidation plant was mothballed in July 1999 and the property was placed on care and maintenance in February 2002 pending further exploration results. The property is currently ramping up to full production status. A joint venture agreement (75% Placer Dome, 25% Newmont) was established with Newmont Mining in 2003 and ore is processed at their nearby Twin Creeks autoclave plant. Mine dewatering is a key element to success. Arsenic is a ubiquitous mineral in many of the mineralized areas of northern Nevada, necessitating treatment of water prior to re-infiltration.

Jan 1, 2005

By Gürkan Bacak

Study area is located on the NorthWestern of Yatagan-Yenikoy and placed in the units of the crystaline Menderes massif of Eagen, Turkey. Stratigraphically gneissic, migmatitic and metagranitic rocks are found at the base. Garnet schists, phyllitic rocks lie unconfirmitelly upon the basement rocks. Permian aged marbles can be observed as diferrent sized lenses within the schists. Triassic, Jurassic and Cretaceous aged gray colored dolomites and pure crystaline calcite bearing marbles lie upon the Permian aged schists. Neogen series, mainly composed of conglomerates, claystones, marl and limestones unconformly cover the other basement series, mentioned above. Pure calcite bearing marble occurances are found at 2 locations in the study area. These are known as Berber Quarry and Kavuk Quarry. Samples numbered as N7, N8, NA from the Berber Quarry, mineralogically composed of Calcite (97-99%)+iron oxide (1-3%) and chemically contain CaCO3 (97,98%), Fe2O3 (0.5-1%), SiO2 (0.025%) N9 and N10, sampled from the Kavuk Quarry-mineralogically composed of Calcite (94,95%)+iron oxide (2-3%)+albite-Quartz (1-2%) and chemically contain CaCO3 (92-93%), SiO2 1.49%, Fe2O3 0.42%. Especially in plastic and paint sector albite and quartz are unwilling minerals due to their hardness. Approximatelly 1/20 of the study area (87.500 km2) contains industrial calcite occurances. Moreover about 100 billion Tons geological, 1.86 billion tons runable (possible) calcite reserve calculated. It can be expected the calcite quality will be increased with depth. During the running stage of the quarries over burden removel and hand sorting processes will positive affect of the quality.

Jan 1, 2005

By Deborah Muggli

Minera Escondida is the world's largest copper mine. Its capacity is more than 800 kt/a (880,000 stpy) of copper. The Escondida open-pit mine operates at an elevation of 3,100 m (10,170 ft). It is located in the Atacama desert about 160 km (100 miles) southeast of the port of Antofagasta. At Coloso, 14 km (8 miles) south of Antofagasta, copper concentrate is dewatered by filtration for storage and shipment to overseas markets (Fig. 1). Concentrate filtrate water, after being treated to remove suspended solids, is discharged at 60 m (200 ft) depth into the Pacific Ocean. This effluent is free of particulates. However, it does contain metal levels above US Environmental Protection Agency (EPA) receiving water criterion. EPA standards are more strict than Chilean receiving water guidelines. However, a multiport diffuser provides rapid mixing of sea water with effluent to ensure metal levels in the receiving water remain below EPA receiving water guidelines. The Escondida Mine began operation in December 1990 at a rated mill capacity of 35 kt/d (38,500 stpd). Since then, the complex has since undergone three expansions. In 1996, it processed 115 kt/d (127,000 stpd) of ore. At Coloso in 1993, about 25% of the copper concentrate was fed to an ammonia leach plant for solvent extraction and electrowinng of cathode copper. This plant is designed to produce 80 kt/a (88,000 st/year) of cathode copper. In 1995, the ocean diffuser system's capacity was doubled to accommodate increased flows to a maximum 50 L/sec (793 gpm). This was achieved by extending the diffuser chamber by 32 m (105 ft) and adding 16 nozzles, which doubled the diffuser's capacity. In November 1996, Rescan Environmental Services began a field verification of the outfall/diffuser system's performance. The study's objective was to determine the performance of the outfall/diffuser system by measuring dilution factors using fluorescent Rhodamine dye and to determine if copper concentrations are below the US Environmental Protection Agency (EPA) water quality criterion of 2.9 µg/L total copper (EPA, 1986). Rhodamine dye was injected into the outfall/diffuser system. An oceanographic survey using an in situ fluorometer was conducted to measure dye concentrations in the effluent plume. Water column characteristics were also measured. These included current speed and direction.

Jan 1, 1997

By R. J. Beckman

This paper traces the history of mica mining in Alabama from 1870-1970. The decline of sheet mica production is noted and emphasis is placed on the more recent activity of scrap mica production and the development of the U. S. Gypsum Co. mica properties in Randolph County, Prospecting for weathered pegmatites of sufficient size to warrant development is a continuing challenge since most deposits are too small and all exhibit varying characteristics as to size, shape, and weathering. Quantity and quality of muscovite mica in the pegmatites is of utmost importance and its recovery during processing of the ore is described.

Jan 1, 1970

By L. A. Panek

A new pillar strength formula is presented. It incorporates a function [IF] of size and shape that takes into account the size-shape interaction effect as well as the enhanced strength exhibited by wide pillars. Existing pillar formulas, lacking these capabilities, are not suitable for extrapolating small-specimen test results to mine-pillar sizes and shapes. Interpreting compressive strength test results as function of [Y] reveals wide-pillar behavior in much old test data. Model relationships are discussed, along with their scaling implications.

Jan 1, 1995

By Anna Marabini

This paper provides a summary of the studies performed over a period of more than fifteen years by the Italian National Research Council's Mineral Processing Institute in Rome to develop applications for the use of chelating reagents in the flotation of metallic minerals. A description is given of the various phases through which the studied progressed, starting with the combined use of commercial chelating reagents and a neutral oil and then moving on to the synthesis of new long-chain chelate collectors for the flotation of sulphide and oxidized Pb, Zn and Cu minerals. After a series of preliminary tests which confirmed the possibility of floating various metallic minerals with commercial reagents containing chelating groups exerting specific action on given cations, the studies were addressed to the development of a theoretical method of choosing chelating groups that exert selective action on one metallic mineral rather than others. The theoretical approach was based on thermodynamic data concerning the chemical equilibria in solution. The validity of the method has been proved in numerous cases by flotation tests on pure minerals. Subsequently the research was directed towards the design and synthesis of reagents with a mixed aliphatic-aromatic structure containing chelating groups for Pb and Zn and an alcoxyl chain of various length, position and configuration. The flotation results obtained on oxidized and mixed Zn-Pb ores provided interesting pointers for designing the nonpolar portion. The structural criteria identified via these studies were interpreted on the basis of chemical and steric considerations. A description is given of a new synthetic chelate collector which is effective in the selective flotation of Cu minerals from complex sulphides. The fact that this reagents is more selective than xanthate is demonstrated by comparative flotation tests on actual ores.

Jan 1, 1994

By Julie Mitchell

The U.S. Bureau of Mines is conducting research on the application of expert sys tens technology to mining equipment diagnostics and predictive maintenance, to increase mining productivity and efficiency. One of the greatest hindrances to mining productivity is the breakdown of equipment, causing lengthy and costly delays. A diagnostic maintenance expert system (DIMES) is being developed for the hydraulic system of a continuous coal mining machine. Through the use of such a system, the frequency of equipment failures and repair time should be significantly reduced. This paper describes the application domain, the functional requirements, and the problem approach for DIMES, the design and implement at i on of the knowledge- based system, the sensor work involved with the project, and the future plans for the continued development of this and other expert systems.

Jan 1, 1989

By P. S. Parobeck, T. F. Tomb, R. S. Ondry

From October 1980 through August 1982, surveys were conducted on 19 longwall mining operations to obtain data relative to respirable dust levels associated with particular longwall operations and occupations, to make recommendations for enhancing dust control, and, where applicable, to evaluate the effectiveness of new technology implemented to control dust. The paper summarizes the data collected during these surveys and, where possible, draws conclusions and discusses actions that can be utilized to reduce exposures to respirable coal mine dust on longwall mining operations.

Jan 1, 1987